Add QSPI node in dtsi(ls1088a), and dts(ls1088ardb, ls1088aqds) boards.
Both ls1088ardb and ls1088aqds has two 64MB flash from SPANSION(s25fs512s).
QUAD I/O is tested in case of read and single I/O is tested in case of
write.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since device properties are different, so remove fsl, ls1021a-qspi.
ls1021a-qspi is to be used only for Big-endian verion of QSPI controller
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the compatibles to use jedec,spi-nor.
Also update the max-frequency to 50MHz and spi-tx-bus-width to 1.
Align the QSPI node with other similar boards like(ls1088ardb,
ls1046afrwy) as per bindings.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board has a single 64MB mt25qu512a flash.
QUAD I/O read and single I/O write is tested.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fspi node property for LS1028A SoC for FlexSPI driver.
Property added for FlexSPI controller and for the connected
slave device for the LS1028ARDB and LS1028AQDS target.
RDB and QDS are having one SPI-NOR flash device, mt35xu02g
connected at CS0.
This flash device "mt35xu02g" is tested for octal read
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently only SAI2 is present in the DT. Add all the other SAI
instances present on the SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change ZII Ultra board names to be more in line with other ZII RDU platforms.
Signed-off-by: Ruslan Sushko <Ruslan.Sushko@zii.aero>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NOC clock defaults to 400 MHz. Increase it to 800 MHz for improved
memory performance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is used by the imx-ddrc devfreq driver to implement dynamic
frequency scaling of DRAM.
Support for proactive scaling via interconnect will come later. The
high-performance bus masters which need that (display, vpu, gpu) are
mostly not yet enabled in upstream anyway.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove "simple-bus" compatible for device anatop,
since no child nodes exist under it and it is not
a populated bus.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove "simple-bus" compatible for device anatop,
since no child nodes exist under it and it is not
a populated bus.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
gic is appointed as default interrupt parent for devices, so no need
to specify it again in device nodes which use it as interrupt parent.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of these at803x properties are documented anywhere, so just
remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO handle is referencing the wrong GPIO, so the voltage did not
actually change as intended. The pinmux is already correct, so just
correct the GPIO number.
Fixes: 4a13b3bec3 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device tree to support Toradex Colibri iMX8X a
computer on module which can be used on different carrier boards.
The module consists of an NXP i.MX 8X family SoC (either i.MX 8DualX or
8QuadXPlus), a PF8100 PMIC, a FastEthernet PHY, 1 or 2 GB of LPDDR4
RAM, some level shifters, a Micron eMMC, a USB hub, an AD7879 resistive
touch controller, an SGTL5000 audio codec and on-module CSI as well as
DSI-LVDS FFC receptacles plus an optional Bluetooth/Wi-Fi module.
Anything that is not self-contained on the module is disabled by
default.
The device tree for the Colibri Evaluation Board includes the module's
device tree and enables the supported peripherals of the carrier board
(the Colibri Evaluation Board supports almost all of them).
So far there is no display or USB functionality supported at all but
basic console UART, eMMC and Ethernet functionality work fine.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi:531.20-581.5: Warning (simple_bus_reg): /soc/tmu@1f00000: simple-bus unit address format error, expected "1f80000"
Fix it by adjusting the tmu unit address to match its reg entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move thermal-zone node from the soc node to the root node.
thermal-zone node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi:583.17-612.5: Warning (simple_bus_reg): /soc/thermal-zones: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts:196.10-208.4: Warning (avoid_unnecessary_addr_size): /soc/i2c@2000000/fpga@66: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Fix it by removing the unnecessary #address-cells/#size-cells.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Machine compatible string normally is located in board DT, remove
the duplicated one from SoC dtsi.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Machine compatible string normally is located in board DT, remove
the duplicated one from SoC dtsi.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add remote control to i.MX8M EVK device tree.
The rc protocol must be selected by writing to:
/sys/devices/platform/ir-receiver/rc/rc0/protocols
On my tests, I used "nec" rc protocol:
echo nec > protocols
Tested using evetest:
evtest /dev/input/event0
Output log for each key pressed:
Event:
time 1568122608.267845, -------------- SYN_REPORT ------------
Event:
time 1568122610.503835, type 4 (EV_MSC), code 4 (MSC_SCAN), value 440
Signed-off-by: Rogerio Pimentel da Silva <rpimentel.silva@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN LPDDR4 EVK board shares most of the device as DDR4 EVK board,
the ONLY difference are the DDR type and PMIC, add support for it
and make it default i.MX8MN EVK board as usual.
The PMIC driver is NOT ready, so cpu-freq needs to be disabled as
it depends on regulator provided by PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN has different EVK boards to support different DDR types,
the ONLY differences are DDR chips and PMIC, so most of the devices
can be shared between these EVK boards, create a EVK dtsi file for
common use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial version of device tree for S32V234-EVB, including nodes for the
4 Cortex-A53 cores, AIPS bus with UART modules, ARM architected timer and
Generic Interrupt Controller (GIC).
Keep SoC level separate from board level to let future boards with this SoC
share common properties, while the dts files will keep board-dependent
properties.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Dan Nica <dan.nica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Phu Luu An <phu.luuan@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign clocks and clock-rates for audio plls, that audio
drivers can utilize them.
Add dai-tdm-slot-num and dai-tdm-slot-width for sound-wm8524,
that sai driver can generate correct bit clock.
Fixes: 13f3b9fdef ("arm64: dts: imx8mm-evk: Enable audio codec wm8524")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Regulator-vsd-3v3 is supplied via GEN_3V3 rail which is an output of
an "always on" load switch supplied by 3V3_MAIN. GEN_3V3 is also used
as vin-supply by a number of peripherals, so adding it also allows us
to follow the schematic more closely.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the property #clock-cells = <1> to #clock-cells = <0> of the
dpclk, since the Display output pixel clock driver provides single
clock output.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA in i.MX8MN should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA in i.MX8MM should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The I2C multiplexer used on ls1028aqds is PCA9547, not PCA9847.
If the wrong compatible was used, this chip will not be able to
be probed correctly and hence fail to work.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MQ EVK board, VDD_ARM is from a DC-DC converter which
is always ON, the GPIO1_IO13 is ONLY to switch VDD_ARM's voltage
between 0.9V and 1V for CPU DVFS, so VDD_ARM's GPIO regulator
should be always ON to avoid below confusion after kernel boot
up:
imx8mqevk login:
[ 31.776619] vdd_arm: disabling
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add scu key node for i.MX8QXP, disabled by default as it
depends on board design.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All nodes are better to follow alphabetical sort except iomuxc
which has huge pinctrl data, better to put it at the end of
file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adjust some nodes to make them follow alphabetical sort except
iomuxc node which is put at the end of file because of its huge
pinctrl data.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
layerscape otg function should be supported HNP SRP and ADP protocol
accroing to rm doc, but dwc3 code not realize it and use id pin to
detect who is host or device(0 is host 1 is device) this patch is to
enable OTG mode on ls1028ardb ls1088ardb and ls1046ardb in dts
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to maximise performance of the LCD Controller's 64-bit AXI
bus, for any give speed bin of the device, the AXI master interface
clock(ACLK) clock can be up to CPU_frequency/2, which is already
capable of optimal performance. In general, ACLK is always expected
to be equal to CPU_frequency/2. APB slave interface clock(PCLK) and
Main processing clock(PCLK) both are tied to the same clock as ACLK.
This change followed the LS1028A Architecture Specification Manual.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Fixes: 00c5ce8ac0 ("arm64: dts: lx2160a: add cpu idle support")
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LX2160A esdhc controllers are setup by the driver to be DMA
coherent, but without marking them as such in DT, Linux thinks they
are not. This can lead to random sporadic DMA errors, even to the
extent of preventing boot, such as:
mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00002202
mmc0: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000001
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present: 0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power: 0x00000003 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x000040d8
mmc0: sdhci: Timeout: 0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab: 0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps: 0x35fa0000 | Caps_1: 0x0000af00
mmc0: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x001d8a33
mmc0: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err: 0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card
These are caused by the device's descriptor fetch hitting speculatively
loaded CPU cache lines that the CPU does not see through the normal,
non-cacheable DMA coherent mapping that it uses for non-coherent
devices.
DT and the device must agree wrt whether the device is DMA coherent or
not.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Temperature and hysteresis were picked after the CPU.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use "fsl,imx8mm-ocotp" as i.MX8MN ocotp's fallback compatible instead
of "fsl,imx7d-ocotp" to support SoC UID read, as i.MX8MN reuses
i.MX8MM's SoC ID driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Compared to i.MX7D, i.MX8MM has different ocotp layout, so it should
NOT use "fsl,imx7d-ocotp" as ocotp's fallback compatible, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN DDR4 EVK board has a GPIO LED to indicate status,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
Fixes: 4a13b3bec3 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYqNmAAoJEFBXWFqHsHzOXFoH/2x5pFXOcHkGcfjWAjguYu4C
gd+fgY/KIBR/t9Fk0Etvi6TRxB6qU061zOrjQSRIB8NCv7zy9P4LuJnyHQsJB8fw
XRYExzxtnsH2NAwpLQN1CX4AFqe9hGEGM3xspck6DQAA5S1fQUBSaak88WqEgfQp
kpf+PnoLMtrG6aUYHQbZXP1WSweH9w6zZwJUlN9YxTeJO91cHCbXdKPZ7NkLasxM
5hLeE8LCFaPGXeAPcgCXyweu2Lv9ncp5R+hx6tb4psfOd18RVz6mTWPYerAW7P/U
EBP/0hTm+7Lk4G4sZJ8a06Of1wBpDD1QprMa0fslzFRt7QzgbOYEvPINlVXRTAk=
=1mGW
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Anson Huang to add i.MX8MN SoC and DDR4 EVK board
device tree support.
- Add DSP device tree support for i.MX8QXP SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYom7AAoJEFBXWFqHsHzOVG8H/RTfCTmRCBaClVZ031GWl/Q2
2NP+AY1l8UE0NKsvEuoMf/VY1atvFNgDvbm4gV1PW5KOBbgZmB3M32lHvXfqbLOu
vACCc8b7JY/8scWUgQBNbE5xAiZjPkLPuIYNJTLmrgVrYkYhtkB/4pwAk9YjVlYt
eHF3SWizKmam8vV3yp6KUNKvEYPBiMBfjSHDUvgT0GHUB4SHpPm/ERruTdKxP0Zm
c730yvV320XiKvxuErdvNfsw6FWs8Bhp8xCIhvF4Wbm0w4c5ucuqHKSV1v63lbbj
GVfdi0cH/eKlugNhfhIH7RsYL5TYjCDwzEyBSnqGCaBW+gnTpRnFkEricgvB+yY=
=3nO3
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-clkdep-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update with new clocks:
- A series from Anson Huang to add i.MX8MN SoC and DDR4 EVK board
device tree support.
- Add DSP device tree support for i.MX8QXP SoC.
* tag 'imx-dt-clkdep-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qxp: Add DSP DT node
arm64: dts: imx8mn: Add cpu-freq support
arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support
arm64: dts: imx8mn-ddr4-evk: Add i2c1 support
arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support
arm64: dts: imx8mn: Add gpio-ranges property
arm64: dts: freescale: Add i.MX8MN dtsi support
clk: imx8: Add DSP related clocks
clk: imx: Add support for i.MX8MN clock driver
clk: imx: Add API for clk unregister when driver probe fail
clk: imx8mm: Make 1416X/1443X PLL macro definitions common for usage
dt-bindings: imx: Add clock binding doc for i.MX8MN
Link: https://lore.kernel.org/r/20190825153237.28829-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SolidRun Hummingboard Pulse carrier board carries the SolidRun
i.MX8MQ based SOM.
Notably missing is PCIe support that depends on analog PLLOUT clock.
Current imx clk driver does not support this clock.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the spi-flash nodes under the DSPI controller for
ls1088a-qds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the DSPI controller node for ls1088a boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the num-lanes property to avoid the driver setting the
link width.
On FSL Layerscape SoCs, the number of lanes assigned to PCIe
controller is not fixed, it is determined by the selected SerDes
protocol in the RCW (Reset Configuration Word).
The PCIe link training is completed automatically through the selected
SerDes protocol - the link width set-up is updated by hardware after
power on reset, so the num-lanes property is not needed for Layerscape
PCIe.
The current num-lanes property was added erroneously, which actually
indicates the maximum lanes the PCIe controller can support up to,
instead of the lanes assigned to the PCIe controller. The link width set
by SerDes protocol will be overridden by the num-lanes property, hence
the subsequent re-training will fail when the assigned lanes do not
match the value in the num-lanes property.
Remove the property to fix the issue
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has a clock domain PXLCLK0 used for the Display output
interface in the display core, independent of the system bus frequency,
for flexible clock design. This display core has its own pixel clock.
This patch enable the pixel clock provider on the LS1028A.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lx2160a platform, the i2c input clock is actually platform pll CLK / 16
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1028a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the nodes to include little-endian
property to be consistent with the hardware.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since fsl-ls1088a Soc GPIO registers are used as little endian,
the patch adds the little-endian attribute to each gpio node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the console device tree node for the following
DPAA2 based platforms: LS1088A, LS2080A, LS2088A and LX2160A.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch use the optional property node "arm,malidp-arqos-value" to
can be dynamic configure QoS signaling.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.
The initial support includes following peripherals which are tested and
known to be working:
1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet
More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All these at803x properties are not documented anywhere, so
just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the charge controller node. With the controller driver loaded
the VBUS of the user USB socket is controlled exclusively via i2c
with the GPIO controls ignored, so vbus-supply for the user USB
port must be linked to the charge controller.
Hog the previously used GPIO control to unconditionally enable
VBUS until the driver is loaded.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf
Fixes: 12629c5c37 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.
https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
Fixes: f403a26c86 (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.
Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since IMX8MM_CLK_USB_CORE_REF is not used at all, so remove the setting
for it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MM pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather than using clock
consumer API in a clock provider driver.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1028a has one Ethernet management interface. On the QDS board, the
MDIO signals are multiplexed to either on-board AR8035 PHY device or
to 4 PCIe slots allowing for SGMII cards.
To enable the Ethernet ENETC Port 1, which can only be connected to a
RGMII PHY, the multiplexer needs to be configured to route the MDIO to
the AR8035 PHY. The MDIO/MDC routing is controlled by bits 7:4 of FPGA
board config register 0x54, and value 0 selects the on-board RGMII PHY.
The FPGA board config registers are accessible on the i2c bus, at address
0x66.
The PF3 MDIO PCIe integrated endpoint device allows for centralized access
to the MDIO bus. Add the corresponding devicetree node and set it to be
the MDIO bus parent.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8M SAI block is not compatible with the i.MX6SX one, as the
register layout has changed due to two version registers being added
at the beginning of the address map. Remove the bogus compatible.
Fixes: 8c61538dc9 ("arm64: dts: imx8mq: Add SAI2 node")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to i.MX8MM reference manual Rev.1, 03/2019:
SAI3_RXC pin's mux option #1 should be GPT1_CLK, NOT GPT1_CAPTURE2;
SAI3_TXFS pin's mux option #1 should be GPT1_CAPTURE2, NOT GPT1_CLK.
Fixes: c1c9d41319 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yUswPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3BrEP/2Hrqr9MHWSZ65iLmRkrMIMQ0nxxngN5//Jt
AlrmyBixwnV3l1eP5lpZT9VlXQL8lo7fkx+03fHPUaKxBihl6DN8LGsSnsT7Wnzu
aGA8SiJmdZhk8f1C30gGNssBBvOdJeTmc0vQzeKXJA6g4ra3+bmwn+T6OLEEGZlO
g0pl7BXST9lNLFlSBEG6DcjNL7m1mqCWpaRmWe70zjbFT86KKb/5YISY61fC7Qkf
AHccunoSXFBM6ttoIubxCInTkhfhKalJyZ2cUPZ6MRxhoE0+ABVOk2lw1oMmF3er
OOz8Qs9AcZcsC6k+WAxJgMjT8snTc8wRh273Df8drGfTzSgGkuXj0Uimmgmaqsts
3xPKu+6+UY+HxDt52NOQ4p/eo8yPMgVutfG7ciGynHZSgsklscLXMvUL7EGH67hR
AfJQFWJ3K+Jk/KeyyGgi1pa2C4BoJ1VmPw1P9oLHRMuuCLrY1B2XzG7nySX81uNG
2uTbLL236o2oUX3E/yaLN1k2tkreddG1G48HVw/srcIImAxD5Dl1sysRzMQRUWBw
tN5ZecSuz/JMQj5HaieZ8zL/v9dXzq6Gielee8SAJaO38nbnmxv3DfTHLLEoy3nv
mS/1OtySzbzI9obMZIsw+bpxDokvb525k89gthxBfWybm6KCRGJO119zc5nZ9r8G
PX5wvaPi
=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add i.MX8MQ based Librem5 devkit support.
- Add SNVS power key support for i.MX8MQ and i.MX8MM.
- Add GPIO alias for imx8mq and i.MX8QXP.
- A series from Daniel Baluta to add SAI devices and enable audio
support for imx8mm-evk board.
- Add DDR performance monitor unit support for i.MX8QXP.
- Add irqsteer interrupt controller device for i.MX8MQ SoC.
- Add CPU speed grading and all OPPs for i.MX8MM and i.MX8MQ.
- Add OCOTP device node for i.MX8QXP.
- Various device addition for LS1028A: SATA, qDMA, USB, Mali DP500 and
temperature sensor.
- Random minor coding style improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEcFcAAoJEFBXWFqHsHzOcNYIAICVsBiJX/gU0t+jT7i1KL83
jDe/DDNg8j9PgR0ElLPejskJgnNYLS0DTWYCY/yPgzK8bwLuqxseVyjXBhyptZ1o
Oecgp9c/79RGsJi9+tFlPKCB/jL4gvagbNn0kPAAoCv3dV5n5FikuSXfsN1v0DJi
JpBXO0IHpkqRTJKk7Ran5MzxxaHbWkjMn0u80ewsAioZv/XhPg5xVSsONleQdh2V
YtZkjcAuA7M9ZOLTKcEFmGyZW/ZTLcW7+xaj9ETJGtMJEi60igPyeFcmd1YIKfIh
g1RwqgDilwEbh2rNulyZbRkRJKQDjTeHUNRqyGEM54lxAB52VQo5hHYa56K2m9Q=
=SIR/
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.3:
- Add i.MX8MQ based Librem5 devkit support.
- Add SNVS power key support for i.MX8MQ and i.MX8MM.
- Add GPIO alias for imx8mq and i.MX8QXP.
- A series from Daniel Baluta to add SAI devices and enable audio
support for imx8mm-evk board.
- Add DDR performance monitor unit support for i.MX8QXP.
- Add irqsteer interrupt controller device for i.MX8MQ SoC.
- Add CPU speed grading and all OPPs for i.MX8MM and i.MX8MQ.
- Add OCOTP device node for i.MX8QXP.
- Various device addition for LS1028A: SATA, qDMA, USB, Mali DP500 and
temperature sensor.
- Random minor coding style improvements.
* tag 'imx-dt64-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
arm64: dts: librem5: enable the SNVS power key
arm64: dts: librem5: Limit the USB to 5V
arm64: dts: imx8qxp: added ddr performance monitor nodes
arm64: dts: imx8qxp: sort LSIO subsystem devices
arm64: dts: imx8qxp: sort alias alphabetically
arm64: dts: imx8qxp: Add lsio_mu13 node
arm64: dts: imx8mm-evk: Enable audio codec wm8524
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
arm64: dts: fsl: ls1028a: Add qDMA node
arm64: dts: imx8mm: Enable SNVS power key according to board design
arm64: dts: imx8mq-evk: Enable SNVS power key
arm64: dts: ls1028a: add crypto node
arm64: dts: ls1028a: Add temperature sensor node
arm64: dts: imx8mm: Move gic node into soc node
arm64: dts: imx8mm: Move usbphy out of soc node
arm64: dts: imx8mm: Pass the 'ranges' property
arm64: dts: imx8mm: Pass a unit name for the 'soc' node
arm64: dts: fsl: imx8mq: add the snvs power key node
arm64: dts: ls1028a: fix watchdog device node
arm64: dts: ls1028a: Enable sata.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The charge controller can handle 14V but the PTC on the devkit can only
handle 6V so limit the negotiated voltage to 5V.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We prefer to sort device nodes under simple bus in order of unit
address. Let's sort the devices under lsio_subsys properly.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has one wm8524 audio codec connected with
SAI3 digital audio interface.
This patch uses simple-card machine driver in order
to enable wm8524 codec.
We need to set:
* SAI3 pinctrl configuration
* codec reset gpio pinctrl configuration
* clock hierarchy
* codec node
* simple-card configuration
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch is to add ptp timer device tree node for dpaa2
platforms(ls1088a/ls208xa/lx2160a).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSCI spec define 1st parameter's bit 16 of function CPU_SUSPEND to
indicate CPU State Type: 0 for standby, 1 for power down. In this
case, we want to select standby for CPU idle feature. But current
setting wrongly select power down and cause CPU SUSPEND fail every
time. Need this fix.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usbphy nodes do not have any register properties and thus
shouldn't be placed inside the bus.
Move usbphy nodes from soc node to root node in order to fix
the following build warnings with W=1:
arch/arm64/boot/dts/freescale/imx8mm.dtsi:681.27-687.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop1: missing or empty reg/ranges property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:710.27-716.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop2: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the 'ranges' property for each one of the AIPS bus in order
to fix the following build warnings:
arch/arm64/boot/dts/freescale/imx8mm.dtsi:209.23-388.5: Warning (unit_address_vs_reg): /soc/bus@30000000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:390.23-439.5: Warning (unit_address_vs_reg): /soc/bus@30400000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:441.23-658.5: Warning (unit_address_vs_reg): /soc/bus@30800000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:660.23-724.5: Warning (unit_address_vs_reg): /soc/bus@32c00000: node has a unit name, but
no reg property
This also aligns with imx8mq.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
