Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When transitioning from SST to MST, the HDCP repeater in some MST
displays will enter a bad state. The HDCP repeater is recovered after
failing and performing authentication again.
[How]
Add monitor patch to trigger HDCP authentication failure after
encryption is enabled and re-authenticate.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Typo in amdgpu_dm error message:
"Failed to found connector for link!"
[How]
1. Replace with:
"Failed to find connector for link!"
2. Fix indentation checkpatch warnings.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reset connection is called before remove display in mod_hdcp. When
remove display is called, the display structure has been zeroed from
reset connection. Since no displays can be found, remove display does
not properly reset the hardware. This causes validation errors when
another display is plugged into a different port afterwards.
[How]
Moved displays structure out of connections structure. Displays
structure is now directly within mod_hdcp. Displays is no longer zeroed
when reset connection is called.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ported from Vega10. SDMA stress tests sometimes see IRQ lost.
Signed-off-by: Samir Dhume <samir.dhume@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
scratch_reg0 is used by RLCG for register access usage
in SRIOV case.
both CP firmware and driver can invoke RLCG to do
certain register access (through scratch_reg0/1/2/3)
but rlcg now dosen't have race concern so if two
clients are in parallel doing the RLCG reg access
then we are colliding,
GFX IB test is a runtime work, so it is forbidden
to use scrach_reg0/1/2/3 during IB test period
note:
Although we can only have this change for SRIOV, but
looks it doesn't worth the effort to differentiate
bare-metal with SRIOV on the GFX ib test
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1)for gfx IB test we shouldn't insert DE meta data
2)we should make sure IB test finished before we
send event 3 to hypervisor otherwise the IDLE from
event 3 will preempt IB test, which is not designed
as a compatible structure for MCBP
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
CP firmware decide to skip setting the state for 3D pipe 1 for Navi1x as there
is no use case.
[how]
Disable 3D pipe 1 on Navi1x.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add debugfs interface amdgpu_force_sclk
to set arbitrary sclk for navi14
v2: Add lock
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a statement that is indented with spaces instead of a tab.
Replace spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change programs CP_ME_CNTL and RLC_CSIB_* through RLC
Signed-off-by: Rohit Khaire <Rohit.Khaire@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds a message lock to the smu_send_smc_msg* implementations to
protect against concurrent access to the mmu registers used to
communicate with the SMU
v2: Implement for smu_v12_0 as well
v3: Add mutex_init for message_lock
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new interface reads the argument in the call to send the message, so
this is no longer needed, and shouldn't be used for concurrency safety
reasons.
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the responsibility for reading argument registers into the
smu_send_smc_msg* implementations, so that adding a message-sending lock
to protect the SMU registers will result in the lock still being held
when the argument is read.
v2: transition smu_v12_0, it's asics, and vega20
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc to pplib interface is changed for navi1x, renoir.
display_config_changed is not called by dc anymore.
smu_write_watermarks_table is not executed for navi1x, renoir
during boot up.
solution: call smu_write_watermarks_table just after dc pass
watermark clock settings to pplib
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SPM_VMID is a global resource, SPM access the video memory according to
SPM_VMID. The initial valude of SPM_VMID is 0 which is used by kernel.
That means UMD can overwrite the memory of VMID0 by enabling SPM, that
is really dangerous.
Initialize SPM_VMID with 0xf, it messes up other user mode process at
most.
v2: squash in indentation fix
Signed-off-by: Jacob He <jacob.he@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For vega10 sriov, the register is blocked, use
copy data command to fix the issue.
v2: Rename amdgpu_kiq_read_clock to gfx_v9_0_kiq_read_clock.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SDMA MQD memory type is NC that causes MQD data overwritten
accidentally by an old stable cache line. Changing it to UC
default for GART will fix the issue.
The mqd_gfx9 parameter is meant for control stacks that are
allocated together with user mode queue MQDs. Setting
mqd_gfx9 to true maps the control stack pages as NC.
Here it was accidentally applied to SDMA MQDs,
which are allocated together with the HIQ MQD. Setting
the mqd_gfx9 to false avoids that.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Given we can query all the asic specific information from amdgpu_gfx_config,
we can make get_tile_config() generic.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two members will be used by KFD later.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead use the pin() callback to detect dynamic DMA-buf handling.
Since amdgpu is now migrated it doesn't make much sense to keep
the extra flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/353997/?series=73646&rev=1
Implement the importer side of unpinned DMA-buf handling.
v2: update page tables immediately
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/353998/?series=73646&rev=1
This implements the exporter side of unpinned DMA-buf handling.
v2: fix minor coding style issues
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/353999/?series=73646&rev=1
Avoid that we ping/pong the buffers when we stop to pin DMA-buf
exports by using the allowed domains for exported buffers.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/353996/?series=73646&rev=1
On the exporter side we add optional explicit pinning callbacks. Which are
called when the importer doesn't implement dynamic handling, move notification
or need the DMA-buf locked in place for its use case.
On the importer side we add an optional move_notify callback. This callback is
used by the exporter to inform the importers that their mappings should be
destroyed as soon as possible.
This allows the exporter to provide the mappings without the need to pin
the backing store.
v2: don't try to invalidate mappings when the callback is NULL,
lock the reservation obj while using the attachments,
add helper to set the callback
v3: move flag for invalidation support into the DMA-buf,
use new attach_info structure to set the callback
v4: use importer_priv field instead of mangling exporter priv.
v5: drop invalidation_supported flag
v6: squash together with pin/unpin changes
v7: pin/unpin takes an attachment now
v8: nuke dma_buf_attachment_(map|unmap)_locked,
everything is now handled backward compatible
v9: always cache when export/importer don't agree on dynamic handling
v10: minimal style cleanup
v11: drop automatically re-entry avoidance
v12: rename callback to move_notify
v13: add might_lock in appropriate places
v14: rebase on separated locking change
v15: add EXPERIMENTAL flag, some more code comments
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/353993/?series=73646&rev=1
We've moved the debugfs handling into a centralized place
so we can remove the legacy load an unload callbacks.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nothing else calls it. Not sure it's necessary.
v2: remove unused port variable.
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split into init and register functions to avoid a segfault
in some configs when the load/unload callbacks are removed.
v2:
- add back accidently dropped has_aux setting
- set dev in late_register
v3:
- fix dp cec ordering
v4:
- squash in kdev reference fix
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To handle debugfs setup on non DP MST connectors.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Into the function that creates the debugfs files rather
than setting them explicitly in the callers.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for display.
v2: add config guard for DC
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The core does this for us now.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for rings.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for firmware.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for register access files.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for gem.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for fence handling.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for SA (sub allocator).
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for pm.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for ttm.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to amdgpu_debugfs_fini. It will be used for other things in
the future.
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since emulators are slower, sometime some operations like flushing tlb
through FM need more than twice the regular timout of 100ms, so increase
the timeout to 1s on emulators.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is the callback function that is going to be invoked
when amdgpu_dpm_set_df_cstate is called to toggle DFCstate
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
two new smc messages added for arcturus with pmfw 54.15.0
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67 ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The previous way of using SDMA queue count to infer whether we should unmap
SDMA engines has bugs. The reason it did not cause issues is because MEC
firmware unmaps all queues (CP + SDMA) when a unmap package for compute
engine is received. Becasue of that, only one unmap queue package
is needed, instead of one unmap queue package for CP and each SDMA engine,
which results in much simpler driver code.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Those printings are duplicated or useless.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the queue creation failed, some resources were not freed. Fix it.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The previous code of calculating active CP queues is problematic if
some SDMA queues are inactive. Fix that by counting CP queues directly.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The queues represented in queue_bitmap are only CP queues.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The name is easier to understand the code.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Devices from Arcturus onwards will have their UUID exposed to Thunk.
Adding neccessary functions to the kernel to propagate the uuid.
Signed-off-by: Divya Shikre <DivyaUday.Shikre@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pp_funcs may not exist, while dpm may be enabled. This change ensures
that KFD topology will report the same as pp_dpm_sclk, as the conditions
for reporting them will be the same.
Otherwise, we may see the issue where KFD reports "100MHz" in topology
as the max speed, while DPM is working correctly.
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change disables programming of GCVM_L2_CNTL* regs on VF.
Signed-off-by: Rohit Khaire <Rohit.Khaire@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This doesn't do anything except auto-init drm_agp support when you
call drm_get_pci_dev(). Which amdgpu stopped doing with
commit b58c11314a
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Fri Jun 2 17:16:31 2017 -0400
drm/amdgpu: drop deprecated drm_get_pci_dev and drm_put_dev
No idea whether this was intentional or accidental breakage, but I
guess anyone who manages to boot a this modern gpu behind an agp
bridge deserves a price. A price I never expect anyone to ever collect
:-)
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Xiaojie Yuan <xiaojie.yuan@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Cc: "Tianci.Yin" <tianci.yin@amd.com>
Cc: "Marek Olšák" <marek.olsak@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This silences the following coccinelle warning:
"WARNING: sum of probable bitmasks, consider |"
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Write a 32-bit value of zero to disable GFXOFF and write a 32-bit
value of non-zero to enable GFXOFF.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_ring_test_helper already handles ring->sched.ready correctly
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add update fences to the root PD while mapping BOs.
Otherwise PDs freed during the mapping won't wait for
updates to finish and can cause corruptions.
v2: rebased on drm-misc-next
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 90b69cdc5f drm/amdgpu: stop adding VM updates fences to the resv obj
Reviewed-by: xinhui pan <xinhui.pan@amd.com>
Tested-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
cleanup amdgpu_ring_fini to check the prerequisites before changing ring->sched.ready
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check Arcturus SKU type to select I2C address of page retirement EEPROM
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
driver needs to take DF out Cstate before any DF register
access. otherwise, the DF register may not be accessible.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
centralize all the xgmi related function to amdgpu_xgmi.c
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The helper function hides software smu and legacy powerplay
implementation for DF Cstate control.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For those ASICs with DF Cstate management centralized to PMFW,
TMR setup should be performed between pmfw loading and other
non-psp firmwares loading.
V2: skip possible SMU firmware reloading
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to trigger eviction as the memory mapping will not be used
anymore.
All pt/pd bos share same resv, hence the same shared eviction fence.
Everytime page table is freed, the fence will be signled and that cuases
kfd unexcepted evictions.
v2: squash in 32 bit fix
CC: Christian König <christian.koenig@amd.com>
CC: Felix Kuehling <felix.kuehling@amd.com>
CC: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This doesn't do anything except auto-init drm_agp support when you
call drm_get_pci_dev(). Which amdgpu stopped doing with
commit b58c11314a
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Fri Jun 2 17:16:31 2017 -0400
drm/amdgpu: drop deprecated drm_get_pci_dev and drm_put_dev
No idea whether this was intentional or accidental breakage, but I
guess anyone who manages to boot a this modern gpu behind an agp
bridge deserves a price. A price I never expect anyone to ever collect
:-)
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Xiaojie Yuan <xiaojie.yuan@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Cc: "Tianci.Yin" <tianci.yin@amd.com>
Cc: "Marek Olšák" <marek.olsak@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.
[How]
Access patches directly from stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.
[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.
[How]
- change old link flag to dc level
- new bit in dc->work_arounds set by DM
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Firmware state helps to debug sequence issues and hangs for DMCUB
commands and we don't have an easy mechanism to dump it from the driver.
[How]
Add a debugfs entry to dump the current firmware state.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dmub_fw_state
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when the rxstatus split was done the index was incorrect. This
lead to HDMI repeater authentication failure for HDCP2.X So fix it
Fixes: 3021690037 ("drm/amd/display: split rxstatus for hdmi and dp")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When calculating nominal refresh rates, don't round.
Only the VSIF needs to be rounded.
[How]
Revert rounding change for nominal and just round when forming the
FreeSync VSIF.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unused VMIDs were not evicted correctly
[How]
1. evict_vmids() logic was fixed;
2. Added boundary check for add_ptb_to_table() and
clear_entry_from_vmid_table() to avoid crash caused by array out of
boundary;
3. For mod_vmid_get_for_ptb(), vimd is changed from unsigned to signed
due to vimd is signed.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DMCU for features like PSR and ABM.
[How]
Add path to dmcu firmware binary and load it for Navi12.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're doing backdoor load then do it entirely ourselves without
invoking any of the frontdoor path to avoid potential issues with
outdated tOS.
[How]
Check the load type and don't pass it to base if we don't want it
loaded.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we execute the first command for ASIC_INIT for command table
offloading we can hit a timing scenario such that the interrupts
for the inbox wptr haven't been enabled yet and the first command
is ignored until the second command is sent.
[How]
This happens when either the SCRATCH0 is already the correct status
code or autoload check is unsupported.
Clear SCRATCH0 during reset.
Also ensure that we don't accidentally reset the ASIC again in case
of a hang by clearing GPINT while we're at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bugs occur when TX interrupt comes in when no USB-C on board.
[How]
Check PHY for USB-C before enabling TX interrupt in DMCU FW.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the i2c payload allocation can fail need to check return codes
[How]
Clean up i2c payload allocations and check for errors
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using a heavy-weight TLB flush once is not sufficient. Concurrent
memory accesses in the same TLB cache line can re-populate TLB entries
from stale texture cache (TC) entries while the heavy-weight TLB
flush is in progress. To fix this race condition, perform another TLB
flush after the heavy-weight one, when TC is known to be clean.
Move the workaround into the low-level TLB flushing functions. This way
they apply to amdgpu as well, and KIQ-based TLB flush only needs to
synchronize once.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for bare-metal we alawys need to load sys/sos/kdb
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
what:
some os preemption path is messed up with world switch preemption
fix:
cleanup those logics so os preemption not mixed with world switch
this patch is a general fix for issues comes from SRIOV MCBP, but
there is still UMD side issues not resovlved yet, so this patch
cannot fix all world switch bug.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1)
we shouldn't load PSP kdb and sys/sos for VF, they are
supposed to be handled by hypervisor
2)
ih reroute doesn't work on VF thus we should avoid calling
it, besides VF should not use those PSP register sets for PF
3)
shouldn't load SMU ucode under SRIOV, otherwise PSP would report
error
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67 ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the firmware versions of arcturus are different from other gfx9
ASICs. And the warning("CP firmware version too old, please update!")
caused by this check can be eliminated.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rlc version of raven_kicer_rlc is different from the legacy rlc
version of raven_rlc. So it needs to add a judgement function for
raven_kicer_rlc and avoid disable GFXOFF when loading raven_kicer_rlc.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When NBIO's RAS error happens, before trigging GPU reset, it's needed
to record error counter information, which can correct the error counter
value missed issue when reading from debugfs.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Once sync flood interrupt is triggered by RAS error, before
actual GPU recovery job, it's necessary to log on and print
non-zero error counter, this will help user knows where the
RAS error source is from quickly.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:980:36:
warning: address of 'sink->edid_caps.panel_patch.skip_scdc_overwrite'
will always evaluate to 'true' [-Wpointer-bool-conversion]
if (&sink->edid_caps.panel_patch.skip_scdc_overwrite)
~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
1 warning generated.
This is probably not what was intended so remove the address of
operator, which matches how skip_scdc_overwrite is handled in the rest
of the driver.
While we're here, drop an extra newline after this if block.
Fixes: a760fc1bff ("drm/amd/display: add monitor patch to disable SCDC read/write")
Link: https://github.com/ClangBuiltLinux/linux/issues/879
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rlc version of raven_kicer_rlc is different from the legacy rlc
version of raven_rlc. So it needs to add a judgement function for
raven_kicer_rlc and avoid disable GFXOFF when loading raven_kicer_rlc.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5JsVQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHZEH+wddtJO4dZk5TZdF
KZB2w2ldsCvrBZAmas1TVvm8ncvUf+ATUZcSIzvZ3YbLmxsuLF2Cz3kD+n+36Mvy
ejwq8Scl7jwnouYps/Gfd6rRj/uCafqST4qp15GMGeiy2ST4A8dJrv5IAgZhD8/N
SN1bSr1AXpZ2JlEzzLDQ/NdVoNMS6IzCOsaINZcc60/XQoQZFRBWamMJFqu+CmXD
SBJOybQNFJhziy45cGZSAl+67sSCcoPftwTs0Stu4CJsvFWRb3MsbNTDS51Hjcc4
3tdgGOhoNXzyzZr96MEAHmiaW4VLQv0PGgUfOajE35viMz48OrwCTru8Kbuae3XM
YHV4qJk=
=yiem
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkpecgAKCRDj7w1vZxhR
xU4CAQD/8ZzfYroiiEI7FHEgvnuldGYZqA9kbNAO2Vueeac0OgD+Jojewdxy+pJ9
dxfA/POdtzx3hOdN+U1YgaDC0hbXwww=
=XgKq
-----END PGP SIGNATURE-----
Merge v5.6-rc2 into drm-misc-next
Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Otherwise we readback all ones. Fixes rlc counter
readback while gfxoff is active.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise we readback all ones. Fixes rlc counter
readback while gfxoff is active.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It's 25 Mhz (refclk / 4). This fixes the interpretation
of the rlc clock counter.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise, the cached dpm features status may be inconsistent under some
case(e.g. baco reset of Navi asic).
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there was a type in the terminate command.
We should be calling psp_dtm_unload() instead of psp_hdcp_unload()
Fixes: 143f230533 ("drm/amdgpu: psp DTM init")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since 'smu_feature_is_enabled(smu, SMU_FEATURE_BACO_BIT)' will always return
false considering the 'smu_system_features_control(smu, false)' disabled
all SMU features.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBLANK callbacks in struct drm_driver are deprecated in favor of
their equivalents in struct drm_crtc_funcs. Convert amdgpu over.
v2:
* don't wrap existing functions; change signature instead
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-6-tzimmermann@suse.de
The callback struct drm_driver.get_scanout_position() is deprecated in
favor of struct drm_crtc_helper_funcs.get_scanout_position(). Convert
amdgpu over.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-5-tzimmermann@suse.de
The copy_to_user() function returns the number of bytes remaining to be
copied, but we want to return a negative error code to the user.
Fixes: 030d5b97a5 ("drm/amdgpu: use amdgpu_device_vram_access in amdgpu_ttm_vram_read")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we readback all ones. Fixes rlc counter
readback while gfxoff is active.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we readback all ones. Fixes rlc counter
readback while gfxoff is active.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's 25 Mhz (refclk / 4). This fixes the interpretation
of the rlc clock counter.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to cover dcn2.x related headers.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In certain situations the message could be reported dozens-to-hundreds of
times, based on how often the function is called.
E.g. If MCLK DPM, any calls to get/set MCLK will result in a failure
message, potentially flooding dmesg. Ratelimit the warnings to avoid
this flood.
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise, the cached dpm features status may be inconsistent under some
case(e.g. baco reset of Navi asic).
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there was a type in the terminate command.
We should be calling psp_dtm_unload() instead of psp_hdcp_unload()
Fixes: 143f230533 ("drm/amdgpu: psp DTM init")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-msg_in is not needed for enabling encryption.
-Use hdcp2_set_encryption instead of hdcp1_enable_encryption for hdcp2.2
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP DTM needs to be aware of the upto date display topology
information in order to validate hardware consistency.
[how]
update HDCP DTM on update_stream_config call.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
According to the specs when bksv or ksv list fails SRM check,
HDCP TX should abort hdcp immediately.
However with the current code HDCP will be reattampt upto 4 times.
[how]
Add the logic that stop HDCP retry if bksv or ksv list
is revoked.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP added a new return code for revoked receivers (SRM). We need to
handle that so we don't retry hdcp
This is already being handled on windows
[How]
Add the enums to psp interface header and handle them.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Seems to work reliably on VI+ except for a few so enable runpm barring
those where baco for runtime power management is not supported.
[rajneesh] Picked https://patchwork.freedesktop.org/patch/335402/ to
enable runtime pm with baco for kfd. Also fixed a checkpatch warning and
added extra checks for VEGA20 and ARCTURUS.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So far the kfd driver implemented same routines for runtime and system
wide suspend and resume (s2idle or mem). During system wide suspend the
kfd aquires an atomic lock that prevents any more user processes to
create queues and interact with kfd driver and amd gpu. This mechanism
created problem when amdgpu device is runtime suspended with BACO
enabled. Any application that relies on kfd driver fails to load because
the driver reports a locked kfd device since gpu is runtime suspended.
However, in an ideal case, when gpu is runtime suspended the kfd driver
should be able to:
- auto resume amdgpu driver whenever a client requests compute service
- prevent runtime suspend for amdgpu while kfd is in use
This change refactors the amdgpu and amdkfd drivers to support BACO and
runtime power management.
Reviewed-by: Oak Zeng <oak.zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During system suspend the kfd driver aquires a lock that prohibits
further kfd actions unless the gpu is resumed. This adds some info which
can be useful while debugging.
Reviewed-by: Oak Zeng <oak.zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_device_suspend might return an error code since it can be called
from both runtime and system suspend flows. Add the missing return code
in case of a failure.
Reviewed-by: Oak Zeng <oak.zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than the FEATURE_ID flags. Avoids a possible reading past
the end of the array.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reported-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x
Update to the latest changes.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x
Former comment looks to be one intended behavior in code,
actually it's not. So correct it.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix warning during switching to dpg pause mode for
VCN firmware Version ENC: 1.1 DEC: 1 VEP: 0 Revision: 16
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GDS clear workaround will cause gfx failure in suspend/resume case.
[ 98.679559] [drm:amdgpu_device_ip_late_init [amdgpu]] *ERROR* late_init of IP block <gfx_v9_0> failed -110
[ 98.679561] PM: dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -110
[ 98.679562] PM: Device 0000:03:00.0 failed to resume async: error -110
As this workaround is specific to the HW bug of GDS's ECC error
existing in cold boot up, so bypass this workaround in suspend/
resume case after booting up.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
hwc->conf was designated specifically for AMD APU IOMMU purposes. This
could cause problems in performance and/or function since APU IOMMU
implementation is elsewhere. Also hwc->conf and hwc->config are
different members of an anonymous union so hwc->conf aliases as
hw->last_tag.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support pause_state for multiple instance, and it will fix vcn2.5 DPG mode
power off issue on instance 1.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to handle the runpm case as well as GPU reset.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need some special handling when using baco vs. other
things.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So we know whether we in are in runtime suspend or
system suspend.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than the FEATURE_ID flags. Avoids a possible reading past
the end of the array.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reported-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As root PD has no parent, we just need move its status to idle.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
CC: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Former comment looks to be one intended behavior in code,
actually it's not. So correct it.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU12 not support WORKLOAD_DEFAULT_BIT and WORKLOAD_PPLIB_POWER_SAVING_BIT.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To pair the latest SMU firmwares.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
