Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the rWTM BIU mailbox node for communication with the secure
processor. The driver already exists in
drivers/mailbox/armada-37xx-rwtm-mailbox.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
RPM clock controller has parent as xo, so specify that in DT node for
rpmhcc
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SolidRun Hummingboard Pulse carrier board carries the SolidRun
i.MX8MQ based SOM.
Notably missing is PCIe support that depends on analog PLLOUT clock.
Current imx clk driver does not support this clock.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the spi-flash nodes under the DSPI controller for
ls1088a-qds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the DSPI controller node for ls1088a boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: 174953de1e
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Remove the num-lanes property to avoid the driver setting the
link width.
On FSL Layerscape SoCs, the number of lanes assigned to PCIe
controller is not fixed, it is determined by the selected SerDes
protocol in the RCW (Reset Configuration Word).
The PCIe link training is completed automatically through the selected
SerDes protocol - the link width set-up is updated by hardware after
power on reset, so the num-lanes property is not needed for Layerscape
PCIe.
The current num-lanes property was added erroneously, which actually
indicates the maximum lanes the PCIe controller can support up to,
instead of the lanes assigned to the PCIe controller. The link width set
by SerDes protocol will be overridden by the num-lanes property, hence
the subsequent re-training will fail when the assigned lanes do not
match the value in the num-lanes property.
Remove the property to fix the issue
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The correct gic number of pwrap is 185 instead of 209. This patch fixes
it to avoid triggering error interrupt.
Fixes: e526c9bc11 ("arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile")
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the regulators found in the mtp platform. This platform consists of
pmic PM8150, PM8150L and PM8009.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file for sm8150-mtp and enables boot to console, adds
tlmm reserved range, resin node, volume down key and also includes pmic
file.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l
with power-on, adc and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with power-on, adc, and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file with cpu, psci, firmware, clock node tlmm and
spmi and enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add fastrpc compute context bank nodes to both cdsp and adsp.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since the R8A774C0 SoC uses DU{0,1} only, the register block length
should be 0x40000.
Based on commit 06585ed38b ("arm64: dts: renesas: r8a77990: Fix
register range of display node") for R-Car E3.
Fixes: 8ed3a6b223 ("arm64: dts: renesas: r8a774c0: Add display output support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add dynamic power coefficients for the Silver and Gold CPU cores of
the Qualcomm SDM845.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the reserved-memory map to version 3, to adjust to changes in the
remoteprocs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
According to rock64 schemetic V2 and V3, the VCC_HOST_5V output is
controlled by USB_20_HOST_DRV, which is the same as VCC_HOST1_5V.
V1 hardware was never sold and only V2/V3 is with customers,
so there is no need to keep a seaprate v1 version around.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has a clock domain PXLCLK0 used for the Display output
interface in the display core, independent of the system bus frequency,
for flexible clock design. This display core has its own pixel clock.
This patch enable the pixel clock provider on the LS1028A.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lx2160a platform, the i2c input clock is actually platform pll CLK / 16
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1028a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the nodes to include little-endian
property to be consistent with the hardware.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the base address of the IPMMU-VC0 block on R-Car V3H is
0xfe990000.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
P710 is a RK3399 based SBC, designed by Leez [0].
Specification
- Rockchip RK3399
- 4/2GB LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
[0]https://leez.lenovo.com
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rockpro64 contains a nor-flash chip connected to spi1.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
[a number of cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- a few small DT fixes for g12a/g12b platforms
-----BEGIN PGP SIGNATURE-----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=bMaE
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
arm64: dts: Amlogic fixes for v5.3-rc
- a few small DT fixes for g12a/g12b platforms
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
-----BEGIN PGP SIGNATURE-----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=nrQp
-----END PGP SIGNATURE-----
Merge tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/FVP update for v5.4
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
* tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fast models: Remove clcd's max-memory-bandwidth
Link: https://lore.kernel.org/r/20190814172408.25995-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply
for each cores of each CPU clusters.
The first cluster uses the "VDDCPU_B" power supply, and the second
cluster uses the "VDDCPU_A" power supply.
Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM
outputs clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of each cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the
Amlogic G12B SoC family, on a board with the same form factor as the
VIM/VIM2 models. It ships in two variants; basic and
pro which differ in RAM and eMMC size:
- 2GB (basic) or 4GB (pro) LPDDR4 RAM
- 16GB (basic) or 32GB (pro) eMMC 5.1 storage
- 16MB SPI flash
- 10/100/1000 Base-T Ethernet
- AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 1x USB 2.0 + 1x USB 3.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 3x LED's (1x red, 1x blue, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- M2 socket with PCIe, USB, ADC & I2C
- 40pin GPIO Header
- 1x micro SD card slot
A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and
A311D SoCs supported by two variants of the board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently there are two nodes named "regulator1" in the Draak DTS: a
3.3V regulator for the eMMC and the LVDS decoder, and a 12V regulator
for the backlight. This causes the former to be overwritten by the
latter.
Fix this by renaming all regulators with numerical suffixes to use named
suffixes, which are less likely to conflict.
Fixes: 4fbd4158fe ("arm64: dts: renesas: r8a77995: draak: Add backlight")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Arm per-CPU architected timers stop ticking in suspend, when the
SCP powers down the CPUs. Flag that in the DT.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson g12b ships with a low-speed (S922X) and high-speed (A311D) variant
so remove cpu_opp_table nodes in meson-g12b.dtsi and create two new dtsi
that can be included in device-specific dts files. Opp points were taken
from the vendor BSP kernel.
Also make meson-g12b-odroid-n2.dts include the new meson-g12b-s922x.dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the base video decoder node compatible with the meson vdec driver,
for GX* chips.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheets in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the OPP table taken from the HardKernel Odroid-N2 DTS.
The Amlogic G12B SoC seems to available in 2 types :
- low-speed: Cortex-A73 Cluster up to 1,704GHz
- high-speed: Cortex-A73 Cluster up to 2.208GHz
The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types.
The Vendor Amlogic A311D OPP table are slighly different, with lower
voltages than the HardKernel S922X tables but seems to be high-speed type.
This adds the conservative OPP table with the S922X higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an HardKernel Odroid-N2 board
running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations for both clusters and checking the final frequency
using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the OPP table taken from the vendor u200 and u211 DTS.
The Amlogic G12A SoC seems to available in 3 types :
- low-speed: up to 1,8GHz
- mid-speed: up to 1,908GHz
- high-speed: up to 2.1GHz
And the S905X2 opp voltages are slightly higher than the S905D2
OPP voltages for the low-speed table.
This adds the conservative OPP table with the S905X2 higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an Amlogic U200 Reference Board,
SeiRobotics SEI510 and X96 Max Set-Top-Boxes running the arm64 cpuburn
at [1] and cycling between all the possible cpufreq translations and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To simplify the representation of differences betweem the G12A and G12B
SoCs, move the common nodes into a meson-g12-common.dtsi file and
express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi.
This separation will help for DVFS and future Amlogic SM1 Family support.
The sd_emmc_a quirk is added in the g12a/g12b since since it's already
known the sd_emmc_a controller is fixed in the next SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Longcheer L8150 is a smartphone based on MSM8916 which is
used in several rebrands like the Snapdragon 410
Android One devices or the Wileyfox Swift.
Add a device tree for L8150 with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
Co-developed-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.
Add a device tree for A3U and A5U with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- Regulators
The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.
The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds Qualcomm Venus video codec DT node for the video
codec hardware found in MSM8996 platforms.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
AOSS hosts resources that can be used to warm up the SoC.
Add nodes for these resources.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on msm8996.
This also adds coresight cpu debug nodes.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on MSM8998.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DT nodes should be ordered by address, then node name, and finally label.
The msm8998 dtsi does not follow this, so clean it up by reordering the
nodes. While we are at it, extend the addresses to be fully 32-bits wide
so that ordering is easy to determine when adding new nodes. Also, two
or so nodes had the wrong address value in their node name (did not match
the reg property), so fix those up as well.
Hopefully going forward, things can be maintained so that a cleanup like
this is not needed.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them
arch/arm64/boot/dts/qcom/qcs404.dtsi:1080.31-1084.7: Warning (unit_address_vs_reg): /thermal-zones/aoss-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1095.33-1099.7: Warning (unit_address_vs_reg): /thermal-zones/q6-hvx-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1110.32-1114.7: Warning (unit_address_vs_reg): /thermal-zones/lpass-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1125.31-1129.7: Warning (unit_address_vs_reg): /thermal-zones/wlan-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1140.34-1144.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1145.34-1149.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1174.31-1178.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1179.31-1183.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1208.31-1212.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1213.31-1217.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1242.31-1246.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1247.31-1251.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1276.31-1280.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1281.31-1285.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1310.30-1314.7: Warning (unit_address_vs_reg): /thermal-zones/gpu-thermal/trips/trip-point@0: node has a unit name, but no reg property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pms405@1 nodes specified unnecessary #address-cells/#size-cells but the
subnodes dont have "ranges" or "reg" so remove it
arch/arm64/boot/dts/qcom/pms405.dtsi:141.21-150.4: Warning (avoid_unnecessary_addr_size): /soc@0/spmi@200f000/pms405@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The adc nodes have reg property but were missing the unit name, so add
that to fix these warnings:
arch/arm64/boot/dts/qcom/pms405.dtsi:91.12-94.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/ref_gnd: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:96.14-99.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vref_1p25: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:101.19-104.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vph_pwr: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:106.13-109.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/die_temp: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:111.27-116.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor1: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:118.27-123.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor3: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:125.22-130.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/xo_temp: node has a reg or ranges property, but no unit name
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Last level cache (aka. system cache) controller provides control
over the last level cache present on SDM845. This cache lies after
the memory noc, right before the DDR.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Node names shouldn't include a vendor prefix and should whenever
possible use a generic identifier. Resolve this by renaming the smmu
nodes "iommu".
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When powering off the Odroid N2, the tflash_vdd regulator is
automatically turned off by the kernel. This is a problem
when issuing the "reboot" command while using an SD card.
The boot ROM does not power this regulator back on, blocking
the reboot process at the boot ROM stage, preventing the
SD card from being detected.
Adding the "regulator-always-on" property fixes the problem.
Signed-off-by: Xavier Ruppen <xruppen@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: c35f6dc5c3 ("arm64: dts: meson: Add minimal support for Odroid-N2")
[khilman: minor subject change: s/meson/amlogic/]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the IR receiver controller on the SEI510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The G12A USB2 OTG capable PHY uses a 8bit large UTMI bus, and the OTG
controller gets the PHY but width by probing the associated phy.
By default it will use 16bit wide settings if a phy is not specified,
in our case we specified the phy, but not the phy-names.
The dwc2 bindings specifies that if phys is present, phy-names shall be
"usb2-phy".
Adding phy-names = "usb2-phy" solves the OTG PHY bus configuration.
Fixes: 9baf7d6be7 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Power rail "D12.0V" comes straight from the power barrel connector,
and it's used in both main board and sub board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Based on similar work from Laurent Pinchart for the r8a7799[05].
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Sort sound child nodes]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is unclear why max-memory-bandwidth should be set for CLCD on the
fast model. Removing that property allows allocating and using 32bpp
buffers, which may be desirable on certain platforms such as
Android.
Reported-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Earlier, the PWM registers were included as part of the pinctrl memory
map, but this turned to be useless as the muxing is being handled by the
SoC pin controller itself. Hence, this commit removes the pwm register
mapping from the pinctrl node to make it more clean.
Fixes: af2ff87de413 ("arm64: dts: bitmain: Add pinctrl support for BM1880 SoC")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add reset controller support for Bitmain BM1880 SoC. This commit also
adds reset support to UART peripherals.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since fsl-ls1088a Soc GPIO registers are used as little endian,
the patch adds the little-endian attribute to each gpio node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the console device tree node for the following
DPAA2 based platforms: LS1088A, LS2080A, LS2088A and LX2160A.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch use the optional property node "arm,malidp-arqos-value" to
can be dynamic configure QoS signaling.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.
The initial support includes following peripherals which are tested and
known to be working:
1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet
More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All these at803x properties are not documented anywhere, so
just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the charge controller node. With the controller driver loaded
the VBUS of the user USB socket is controlled exclusively via i2c
with the GPIO controls ignored, so vbus-supply for the user USB
port must be linked to the charge controller.
Hog the previously used GPIO control to unconditionally enable
VBUS until the driver is loaded.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf
Fixes: 12629c5c37 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.
https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
Fixes: f403a26c86 (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.
Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since IMX8MM_CLK_USB_CORE_REF is not used at all, so remove the setting
for it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MM pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather than using clock
consumer API in a clock provider driver.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1028a has one Ethernet management interface. On the QDS board, the
MDIO signals are multiplexed to either on-board AR8035 PHY device or
to 4 PCIe slots allowing for SGMII cards.
To enable the Ethernet ENETC Port 1, which can only be connected to a
RGMII PHY, the multiplexer needs to be configured to route the MDIO to
the AR8035 PHY. The MDIO/MDC routing is controlled by bits 7:4 of FPGA
board config register 0x54, and value 0 selects the on-board RGMII PHY.
The FPGA board config registers are accessible on the i2c bus, at address
0x66.
The PF3 MDIO PCIe integrated endpoint device allows for centralized access
to the MDIO bus. Add the corresponding devicetree node and set it to be
the MDIO bus parent.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[geert: Sort i2c slave nodes]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[geert: Sort i2c slave nodes]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
