At some point during rebases these were shuffled around. Put them in the
right order again (sorted by unit-address).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653 ("arm64: zynqmp: Add support for Xilinx zcu100-revC")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add regulators to the Tegra210 Darcy DTS file including support for
the MAX77620 PMIC.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add initial device-tree support for NVIDIA Shield TV (a.k.a. Darcy)
based upon Tegra210 SoC with 3 GiB of LPDDR4 RAM.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of hardcoding the value (0), reuse the symbolic name from
dt-bindings/interrupt-controller/arm-gic.h.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix IRQ type of PMIC which should be configured as high-level trigger.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the register range of apbmisc, that originally inherited from
Tegra124.
Reported-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
gpio-keys,name is not a valid property supported by gpio-keys
driver so remove it from DTS.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Define all six QUP controllers, both as SPI and I2C, allowing boards to
enable these as needed. Associated pinmux states are also defined, to
require only pinconf states to be specified by the boards, as they are
enabled.
Note that SPI has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the BLSP2 BAM and add the remaining four UARTs found on the QCS404
platform.
Note that these has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
BLSP1 UART2 is used as debug uart on the EVB development board, define
pinmux state for the UART in the platform dtsi and pinconf state for it
in the board dts.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fix up the lpasscc address and size, missed during the conversion to
address- and size-cells of 2.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the duplicate inclusion of qcom,gcc-sdm845.h
mistakenly introduced by commit 6e17f81405 ("arm64:
dts: sdm845: add prng-ee node").
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
[bjorn: Also fix sort order of lpasscc include, while we're there]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add reserve-memory nodes for mpss and mba required for
remoteproc mss pil.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the gpio-ranges property to the TLMM node so that GPIO hogs work.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
For devices attached to an IOMMU, translation between IOVA and physical
addresses is no longer 1:1 and dma-ranges should be specified to
describe the available IOVA address space.
On SDM845 the busses are implemented with 36 address bits, so dma-ranges
must be defined to reduce the size of the IOVA address space from the 48
bits supported by the SMMU. Without this DMA allocations may end up with
IOVAs outside the valid range, that gets truncated by the bus between
the device and its translation unit.
Also extend ranges to describe the available address space.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The busses on SDM845 provides 36 address bits, extend the address and
size cells to make it possible to describe this in "ranges" and
"dma-ranges".
While touching all reg properties, addresses are padded to 8 digits.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on SDM845 soc.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the node to support PDC Global reset driver on
SDM845 SoCs
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Correct address for pcs_misc register region of USB3 QMP UNI PHY.
These registers are used during runtime-suspend/resume routines
of phy.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: ca4db2b538 ("arm64: dts: qcom: sdm845: Add USB-related nodes")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the low pass audio clock controller node to sdm845 based on
the example in the bindings.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[bjorn: Disabled lpasscc node, as it's normally protected]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the video clock controller node to sdm845 based on the examples
in the bindings.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the GPU clock controller nodes as per the example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Quad SPI controller to the main sdm845 device tree file.
Boards will be expected to assign the proper pinctrl depending on how
many chip selects they have hooked up and how many data lines.
This depends on commit 48735597f7 ("clk: qcom: Add qspi (Quad SPI)
clock defines for sdm845 to header") to add the needed defines. It
also shouldn't land until the patch ("dt-bindings: spi: Qualcomm Quad
SPI(QSPI) documentation") [1] lands.
[1] https://lkml.kernel.org/r/20181002214709.162330-1-ryandcase@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
msm8998 has a dozen i2c controllers which can be used to connect to board
specific peripherals. Enumerate the controllers so that boards can wire
up as needed.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[bjorn: Renumbered labels on BLSP2 nodes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
l21 is used as sdcard vmmc, and needs the load increased to prevent
voltage drop issues with some sdcards. This addresses -84 errors seen
during sdcard init with SDR104 cards.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DPU is short for the Display Processing Unit. It is the display
controller on Qualcomm SDM845 chips.
This change adds MDSS and DSI nodes to enable display on the
target device.
Changes in v2:
- Beefed up commit message
- Use SoC specific compatibles for mdss and dpu (Rob H)
- Use assigned-clocks to set initial clock frequency(Rob H)
Changes in v3:
- added IOMMU node
- Fix device naming (remove _phys)
- Use correct IRQ_TYPE in interrupt specifiers
Changes in v4:
- move mdss node to preserve the unit address sort order
- remove _clk suffix from dsi clocks
(both the comments are from Doug Anderson)
Changes in v5:
- Keep the device status "disabled" by default (Bjorn Andersson)
- Use MDSS_GDSC macro (Jordan)
- Fix phy-names (Jordan)
- List reg ranges in numerical order (Jordan)
Changes in v6:
- Separating this patch out of the series
- fix phy-names
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As instability in the architectural timer has been observed on multiple
devices using this SoC, inluding the Pine64 and the Orange Pi Win,
enable the workaround in the SoC's device tree.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch adds ethernet support to the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pincontrol support to scif2.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Si-Linux board based on RZ/G2E:
- Memory,
- Main crystal,
- Serial console
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS400 of SDHI3 using the corresponding DT property.
No further changes are required.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
SCIF2 on R-Car E3 can be used with both DMAC1 and DMAC2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on RZ/G2E can be used with both DMAC1 and DMAC2.
Fixes: 1b24f9e8ea3ff95f ("arm64: dts: renesas: r8a774c0: Add SCIF and HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There are two regulator1 nodes in the Ebisu DTS right now, one 3.3V for
the eMMC and one 12V for the backlight. This causes one to be overwritten
by the other, ultimatelly resulting in inoperable eMMC, which depends on
the former. Fix this by renumbering the backlight regulator to regulator2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 9d16c4a10e ("arm64: dts: renesas: r8a77990: ebisu: Add backlight")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the V3M Starter Kit board's device tree, now
that we have the GPIO support (previously phylib had to resort to polling).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Ebisu board is using simple-scu-audio-card
which is used for Sampling Rate Convert, or MIXer, etc.
But, Ebisu is not using such feature.
Then, simple-audio-card is very enough.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Before, BUSIF which is needed for DMA transfer was automatically handled
via SSI, but it cared BUSIF0 only.
Now, rsnd driver can handle BUSIF0-7 (= for Gen3) BUSIF0-3 (= for Gen2)
via SSIU, and it is keeping compatibility.
Thus, BUSIF0 settings via SSI had been kept to avoid git merge timing
issue / git bisect issue, but it is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Before, BUSIF which is needed for DMA transfer was automatically handled
via SSI, but it cared BUSIF0 only.
Now, rsnd driver can handle BUSIF0-7 (= for Gen3) BUSIF0-3 (= for Gen2)
via SSIU, and it is keeping compatibility.
Thus, BUSIF0 settings via SSI had been kept to avoid git merge timing
issue / git bisect issue, but it is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
KingFisher has pcm3168 sound codec. This patch enables it.
Because pcm3168 can't handle symmetric channel on playback/
capture, we need to handle it as different DAI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing ULCB HDMI sound support.
To use sound card, HDMI video is mandatory.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ULCB can use daughter board which is called as KingFisher.
It has extra sound interface, thus we want to use it.
But, basically, ALSA SoC can't use Multiple sound card with single
CPU sound interface (= SSI). Thus we need to use Single Sound Card
with multiple DAI interface.
To be easy to expand ULCB sound card on KingFisher, it is better to
use multi-dai-link style sound card on ULCB sound DT.
Now, "simple-audio-card" / "audio-graph-card" both can support
multi-dai-link style, but HDMI sound support (which is not yet supported
on ULCB) needs "audio-graph-card".
Using audio-graph-card is better selection.
This patch exchange current sound card to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 6d2ca85279 ("dt-bindings: display: renesas: Deprecate
LVDS support in the DU bindings"), the internal LVDS encoder has DT
bindings separate from the DU. The device trees for all R-Car H3 and
M3-W development boards were ported over to the new model, but
Salvator-XS boards equipped with an R-Car M3-W SoC were forgotten.
Fixes: 58e8ed2ee9 ("arm64: dts: renesas: Convert to new LVDS DT bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the i2c nodes so that sub-nodes of the soc node are sorted by bus
address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the pciec0 node so that sub-nodes of the soc node are
sorted by bus address.
This change has no run-time affect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for VIN4, VIN5 and CSI40 to RZ/G2E (a.k.a. R8A774C0)
SoC specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PCI express channel 0 device tree node to the
RZ/G2E (a.k.a. R8A774C0) SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the RZ/G2E Audio-DMAC device to IPMMU-MP as stated by the
RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the RZ/G2E AVB device to IPMMU-DS0 as stated by the
RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1, and SYS-DMAC2 to IPMMU-DS0 and
IPMMU-DS1, according to what reported by the RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb3.0 host and function device nodes to the RZ/G2E SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/G2E (a.k.a. R8A774C0) has one RGB output and two LVDS
outputs connected to DU.
This patch add support for DU, LVDS encoders, VSP and FCP.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add PWM support to the RZ/G2E (a.k.a. R8A774C0) SoC specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G2E SoC (a.k.a. R8A774C0).
This work is based on similar work done on the R8A77990 SoC
by Yoshihiro Kaneko <ykaneko0929@gmail.com>.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers on RZ/G2E SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the thermal device node and the thermal-zones
node to the SoC specific dtsi for the RZ/G2E.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for both RZ/G2E CAN channels.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-7] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774c0 device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a774c0 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
RZ/G2E (a.k.a r8a774c0) SoC, and adjust the interrupt delivery masks
for the ARM Generic Interrupt Controller and Architectured Timer.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog support to the RZ/G2E (a.k.a. R8A774C0) SoC
specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO device nodes to the DT of the r8a774c0 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add PFC support to the RZ/G2E (a.k.a. r8a774c0) SoC specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2E.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2E SCIF and HSCIF serial ports,
including clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G2E SoC (a.k.a. r8a774c0).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode doesn't support
on R-Car E3. This patch fixes EthernetAVB phy mode to rgmii.
This is achieved by simply dropping the phy-mode property from
r8a77990-ebisu.dts as the default property for this for r8a77990,
as set in r8a77990.dtsi, is "rgmii".
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Limiting the HS200 rate on the s400 was just a way to mask that the
tuning setting were not correct. This seems to have been fixed with
the recent MMC driver update. We can now use HS200 at full speed.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The bcm wifi/bt device on SDIO support SDR104 and it seems to work
well following the recent mmc driver update, so enable this
ultra high speed mode
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SimpleFB allows transferring a framebuffer from the firmware/bootloader
to the kernel, while making sure the related clocks and power supplies
stay enabled.
Add nodes for CVBS and HDMI Simple Framebuffers.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Allows the vpu driver to optionally use a canvas provider node.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For whatever reason, the sdmmc_dectn function isn't working properly
as-is, and microSD insertion and removal goes unnoticed. Using the pin
as a GPIO interrupt instead is rather noisy without any debouncing, but
is good enough to make it useful until someone feels inclined to figure
out how the vendor kernel/firmware gets the dedicated function to work
with no obvious difference in the pinmux/GRF configuration. Let's also
take the opportunity to tweak the node name so that all related pins
end up grouped together in the compiled DTB.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In common with most Rockchip reference designs, NanoPC-T4 has a passive
IR receiver connected to PWM3. In lieu of a specialised driver for
PWM-based IR pulse measurement, running the pin as a GPIO with the basic
driver works perfectly well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The nanopi4 boards differ primarily in their power trees, with the main
5V and 3.3V rails having very different topologies on the smaller USB-C
powered boards vs. the 12V-powered T4, as well as minor variation in
other regulators related to various external connectors.
Additionally, the recovery key is only present on the T4 - ADC_IN1 is
simply pulled high and not exposed on the other boards - and the lowest
common denominator for MMC speed is actually HS200 according to the
vendor DTs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are a number of subtle differences between the nanopi4 variants,
and where they disagree, the common DTSI currently follows the details
of NanoPi M4. In order to improve matters even more, let's add a
separate DTS for the M4 to which we can start splitting things out
appropriately. The third variant, NanoPi NEO4, is a lot closer to the M4
than either is to the larger T4, so arguably could get away with just
sharing the M4 DT for now (plus I have neither of the smaller boards to
actually test with).
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SCIF2 on R-Car M3-N can be used with both DMAC1 and DMAC2.
Fixes: 0ea5b2fd38 ("arm64: dts: renesas: r8a77965: Add SCIF device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on R-Car M3-W can be used with both DMAC1 and DMAC2.
Fixes: dbcae5ea4b ("arm64: dts: r8a7796: Enable SCIF DMA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on RZ/G2M can be used with both DMAC1 and DMAC2.
Fixes: 3a3933a4fa ("arm64: dts: renesas: r8a774a1: Add SCIF and HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds support for the power domain controller found on the
i.MX8MQ SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We can reuse the pwm from fsl,imx27-pwm as with other imx SOCs.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This typo inverted the meaning of the comment, but the rest of the
comment and the code reveal that the regulator in question needs to be
on at all times.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
gpiio5 is missspelt in msm8996-pins.dtsi, fix that.
Signed-off-by: Jakob Wuhrer <jakobwuhrer@airmail.cc>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In the same way as for msm8974-hammerhead, l11 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Tested on Dragonboard-410c and DART-SD410 boards.
Fixes: 4c7d53d16d (arm64: dts: apq8016-sbc: add regulators support)
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The PMS405 PMIC has an ADC that exposes the on-die temperature that we
wire up to spmi-temp-alarm thermal driver. This allows the PMIC
temperature to be exposed to Linux through the thermal framework.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on qcs404 soc.
Optional clock and regulator controls are not yet available in
upstream, hence add them once available.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The controller can support EXT_CSD_CARD_TYPE_HS400_1_8V cards.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This change adds the cpufreq node as per the bindings example for SDM845.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the second lane registers for the USB PHY, now that the
QMP phy bindings have been updated. This way the driver can stop
reaching beyond its register region to get at the second lane.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the UFS host controller and PHY on sdm845-mtp.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the UFS controller and PHY to SDM845.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add iommu context for the host controller]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for arm,mmu-500 available on sdm845.
This MMU-500 with single TCU and multiple TBU architecture
is shared among all the peripherals except gpu.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable support for one of the micro SD slots on the MTP.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add one of the two SD controllers to SDM845.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
ROCK Pi 4 is RK3399 based SBC from radxa.com. board has a 1G/2G/4G lpddr4, CSI,
DSI, HDMI, OTG, USB 2.0, USB 3.0, 10/100/1000 RGMII Ethernet Phy, es8316 codec,
POE, WIFI (for Model B only), PCIE M.2 support on board.
This patch enables
- HDMI Display
- Console
- MMC, EMMC
- USB 2.0, USB-3.0
- Ethernet
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Pragnesh Patel <Pragnesh_Patel@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add this property to all layerscape platforms to improve USB read write performance.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the UARTs by defaultto avoid registering unused UARTs. This
effectively change the number of registered UARTS for the RDB and QDS from
4 to 2 but this seems the right thing to do.
It is especially useful when connecting other 8250 uart on PCIe for example
as the default maximum number of 8250 UARTs that can be registered is 4.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set the Integrated Flash Controller status to disabled so each board has
the option to enable it. All the existing users have status = "okay" so
there is no functional change.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a generic node name for the m25p80 flashes on ls1043 and ls1046 boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch also adds the iommu-map property in fsl-mc node, so
that fsl-mc can use iommu.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add num-viewport property for PCIe DT nodes to specify how many
viewports are implemented.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The were added at the end of the AIPS1 address space, while they
are in fact in the middle.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable spdif input device on the S400 and add it to the card
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SPDIF capture codec to the axg s400 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SPDIF input device of the axg audio subsystem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds a device tree for the NanoPC-T4 SBC, which is based on the
Rockchip RK3399 SoC and marketed by FriendlyELEC.
Known working:
- Serial
- Ethernet
- HDMI
- USB 2.0
All of the interesting stuff is in a .dtsi because there are at least
two other boards that share most of it: NanoPi M4 and NanoPi NEO4.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[rm: various further cleanup]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MPP52 signal is on the seconds GPIO instance of CP0, which
corresponds to the &cp0_gpio2 handle.
Rename the property name to the standard '-gpios' suffix while at it.
Fixes: b83e1669ad ("arm64: dts: marvell: mcbin: add support for PCIe")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from Linux leads to an immediate crash.
So let's make the same memory reservation as the vendor kernel.
[gregory: added as comment that this region matches the mainline U-boot]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f91 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pinmux support for UART1 on MediatekX20 Development board based
on Mediatek MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Now there are device tree clocks for the ARM64 SMMU,
add SMMU support to the Stratix10 Device Tree which
includes adding the SMMU node and adding IOMMU stream
ids to the SMMU peripherals.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The backlight levels provided in the Draak DT produce a perceived
brightness very biased towards high brightness. Use better brightness
levels based on the CIE 1931 formula.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the backlight device for the LVDS1 output, in preparation for panel
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When introducing the video-codec node for the video engine, the
compatible for the H5 was used instead of the compatible for the
A64. Use the right compatible instead.
Fixes: d60ce24740 ("arm64: dts: allwinner: a64: Add Video Engine node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on Teres I Laptop.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Rock64 boards has analog audio jack on it. RK3328 can output
analog audio signal using I2S1 and ACODEC core.
This patch adds sound node for analog audio for Rock64.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3328 i2s and spdif controllers only ever have one output
connection, so as with all implementations of the rk3066 i2s
controllers we can keep the #sound-dai-cells in the main dtsi
instead of having it repeated in each board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds audio codec (ACODEC) node that converts to analog
audio signal from I2S for rk3328.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlwqdD8PHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3NQQP+gNhDCR01wy8EqmCuUn1nmoatnF9ViYER9yw
tlWysax29ba5DGuSKkBCRooTDUNlVIMPdb7vE74CWoDVubexab67qFVJz+uRsXC5
Gt/10STcU/i/Ga4bpkJxz47PfLHpVw1IwKUV1eoFWtLF7QQwfxiH8mr7vZj7XQo2
3K95Adf13E6iIfbHcfBgEF0CjImUiZVq2E0DWMsE0Yti0ygVkNZeRXGHAUfQm/kD
bBYOaHuuuiCXKp7dF9vzAC+iAqerudWYvxuHKPY0pU8T8hpj5P+UjGgCSeRdsLJz
30MRr3t9WhPKvUYDVdIwsE5o1y1S2ZzO1FrTeRiJ8pem8PTliljXE3bIeTvu7uct
n9lNquwvcjVutX7uYOesUmfGLGKQlCwwgg0l997OLe7/o9hzAdnptVvTciCVoanI
r0ACjazbgIHGdb5rFLb5/Kkb+IqOc0d57CHiQacri1MN5zSQ9wLCZpXH8YEdibcI
zY0DBlH2ga7Qh7rtlPi4I0gLNUG8jYclUwRbQYUKGlh0Bsv/J4abR49UC4byn2Vj
kdEO1ASaNIwMJgBgSNAIoop/JhEnO+/ECJoB/pYCvNts6W/LckbMtPVhAofTIVTz
B0pAexDPT4HW//vQ7iOmXraIeUi/HDTaT/64gWsoMnF6LntgcF79NDx4KJDXNRId
Jra+EkHq
=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
- It contains the initial device tree support for i.MX8MQ - the first
ARM64 i.MX processor. It features a quad Cortex-A53 core that
operates at speeds of up to 1.3 GHz, a Cortex-M4 core for
low-power processing, a DRAM controller that supports 32-bit/16-bit
LPDDR4/DDR4/DDR3L memory, and hardware acceleration for 4K video
playback.
- A couple of patches from Baruch that add watchdog device for i.MX8MQ
enable it for imx8mq-evk board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcFjGjAAoJEFBXWFqHsHzOqtcIAJqypaN00zz50FHWeZG3Z6qK
lcaseee6AMTxBZRpQdU1sZoONQ3Q4azlV4KJk/XZqCso6pqYkCc3yLrTb4y1YlBu
usH9Ap66KkqUXjT6239bysxOAxL73wV8ekn+al52PAcjEuYAWzmKoIbnRWijyZaE
BaLXpEInQxh8GhM7CddCZV6xbNem+d9zOm0YE46YltgZdfJGgxrTxdnWyC/8uGrX
FK+mnjaxjWa6gsnYf4PpYXZowpzsq1MOY1Hwk8snfSJPTA3wxus9VRIyEL2KalS+
mQ5pWwL1naRloQAa3/VLmp69+7B4MXnh0ws7WZmh/BB1JxZIes4RSE1jp1hWMJI=
=OAS0
-----END PGP SIGNATURE-----
Merge tag 'imx8mq-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/late
i.MX8MQ device tree support for 4.21:
- It contains the initial device tree support for i.MX8MQ - the first
ARM64 i.MX processor. It features a quad Cortex-A53 core that
operates at speeds of up to 1.3 GHz, a Cortex-M4 core for
low-power processing, a DRAM controller that supports 32-bit/16-bit
LPDDR4/DDR4/DDR3L memory, and hardware acceleration for 4K video
playback.
- A couple of patches from Baruch that add watchdog device for i.MX8MQ
enable it for imx8mq-evk board.
* tag 'imx8mq-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
arm64: add basic Kconfig symbols for i.MX8
arm64: dts: ls1046a: add qdma device tree nodes
arm64: dts: ls1043a: add qdma device tree nodes
arm64: dts: ls1088a: Add missing dma-ranges property
arm64: dts: ls1088a: Move fsl-mc node
arm64: dts: fsl: Add all CPUs in cooling maps
arm64: dts: Add support for NXP LS1028A SoC
arm64: dts: layerscape: removed compatible string "snps,dw-pcie"
arm64: dts: fsl: Add the status property disable PCIe
arm64: dts: ls1012a: Add FRWY-LS1012A board support
dt-bindings: Add binding for i.MX8MQ CCM
arm64: dts: add LX2160AQDS board support
arm64: dts: add LX2160ARDB board support
arm64: dts: add QorIQ LX2160A SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
-----BEGIN PGP SIGNATURE-----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=BNeo
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC Fixes for v4.20
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
* tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: draak: Fix CVBS input
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
-----BEGIN PGP SIGNATURE-----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=Ks3Q
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21 - round 2
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcFg+pAAoJEFBXWFqHsHzOC3UH/RsA0ysBXsaUF9aNpfmwFpKP
bApnoyo+MhLZSvFqD8eU1K0BhXFOkOmMXMbTle0b3uF7qaknnXEoWTCNz+hJGDsz
fFeOqz7xjyG8Q4U8PT4ImG0OPuFNNGBs1byJKZygxJp/xBlAGMKDp/rRKbM4c8+8
WzoKcWcLqFe+Vau0vuesjcT7J/B3nWvzOWsWX5MHOp10rEWyv9Y4Ct3cAzSMVhAM
1eLQpYegOvUckX0if7BZpj7vSIhDNp/urx6U7D5KGAf9iHK50euMX55LhveiSM8w
CdnnZn2MUXEt2A81Aqb97IOhMsEra47Ffomr1nIV2OGbmDY27HrlUrNSEKNER28=
=I3dR
-----END PGP SIGNATURE-----
Merge tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
* tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO2 provides
overall power via VBAT, and DLDO4 provides I/O power via VDDIO. The RTC
clock output provides the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for Bluetooth,
but this is not covered here.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
TM2(e) boards have a Broadcom Bluetooth chip connected to 3rd UART port.
Add a device tree node describing it and its resources (control GPIO lines
and clock).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The external nWDOG signal connects to the EVK board reset circuit.
Tested on the i.MX8MQ EVK rev B3.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the evaluation kit board for the i.MX8M. The current level of
support yields a working console and is able to boot userspace from
SD card or Network.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> (v1)
Reviewed-by: Rob Herring <robh@kernel.org> (v3)
Tested-by: Tested-by: Baruch Siach <baruch@tkos.co.il> (v1)
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the basic DTS for the i.MX8MQ.
For now only the following peripherals are supported:
- IOMUXC (pin controller)
- CCM (clock controller)
- GPIO
- UART
- uSDHC (SD/eMMC controller)
- FEC (ethernet controller)
- i2c
This is enough to get a very basic board support up and running.
One known limitation is that the driver for the GPC interrupt
controller is still missing, rendering the CPU sleep states unusable
as there is nothing waking them up anymore.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The properties 'num-cs' and 'bus-num' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable McSPI0 of main domain and add DT node for the SPI NOR flash
connected to CS0.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 3 instances of McSPI in MCU domain and 4 instances in Main domain.
Add DT nodes for all McSPI instances present on AM654 SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Populate power-domain property for UART nodes, this is required for
Linux to enable UART clocks via PM calls. Without this UART instances
not initialized by bootloader (like main_uart1) fails to work in Linux.
Also, drop current-speed property from main_uart1 and main_uart2 nodes
as these UARTs are not initialized before Linux boots up and current
speed is unknown.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add pinmux for main uart0 that is serves as console on AM654 EVM
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add pinctrl regions for the main and wkup mmr.
The range for main pinctrl region contains a gap
at offset 0x2e4, and because of this, the pinctrl
range is split into two sections.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqJJwAKCRDj7w1vZxhR
xTq4AP9SxrPeKDTBD4mKV+PVuJ2qq919M6o+mcxDkCecEMfbagD+JLkt2uGzdpb8
eC6CuieHvJq1y/akfDpRBf0ZZD0/bw0=
=yRd0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
hdmi output for rockpro64, vpu node on rk3399 and adding the
always on 32kHz clock on rk3399-Gru to get a more complete clock
tree.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlwQxHMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTbOCACON4DSK2x1MpKOOcUMniqPW6Q7KP3o5MJ6
vTgBHdnjTK4LQLrq/B0LBwe4czJSj0uKxdf4bPddZgZSvM1bSdjQ7YHoZNRB5UTx
pO4qiiGdLw4CAAMEhaOivN51KBxri+qyUNq/Pyh5lhhyrqjPswDzyA4ou22SaXzY
2BqT8tzHDUmCzXM+0mD+81VMCQax5rezjDFeod6MRT5oSqa4xht7fd4M2Wc5Vqkr
B0YfdWvH9ey06vF8bLm2828yA6Gr3uCEHbkVD15PNBGixN0aRSSH6BEThFih+PHq
nMkN51wZepnkW3q8wIU6O46UERWE7ySmyZD8ph45IuPtEBXy+aOG
=s5pB
-----END PGP SIGNATURE-----
Merge tag 'v4.21-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Support for the onboard LEDs of the 2 96boards (ficus, rock960),
hdmi output for rockpro64, vpu node on rk3399 and adding the
always on 32kHz clock on rk3399-Gru to get a more complete clock
tree.
* tag 'v4.21-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add on-board LED support on rk3399-rock960
arm64: dts: rockchip: Add on-board LED support on rk3399-ficus
arm64: dts: rockchip: enable hdmi output on rk3399-rockpro64
arm64: dts: rockchip: add VPU device node for RK3399
arm64: dts: rockchip: Add 32k clk on rk3399-gru
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add device tree for LS1028A SoC and NXP FRWY & QDS boards support
based on this SoC.
- Add device tree for LX2160A SoC and NXP QDS & RDB boards support
based on this SoC.
- Add qdma devices for LS1043A and LS1046A SoC.
- Disable PCIe device by default in SoC device tree and let board level
device tree to enable as needed.
- Drop compatible string "snps,dw-pcie" from LayerScape PCIe devices to
avoid incorrect matching.
- Move fsl-mc device as a child node of soc node, and add missing
dma-ranges property for LS1088A SoC.
- Update LayerScape SoCs' cooling maps to include all devices affected
by individual trip points.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDgwJAAoJEFBXWFqHsHzObhIH/0knVFbw3ubCvjxdYh3wKkKp
B7D39BTQZUwJXNc9To79TKsnFbCW9QucofRKeZN6Ln/qIkvPrlmyQ7bafaz6Lah4
i++bNIyDtHUQ0ZBB/37vl5n+KRbX7CnRsGwEiZnOCBXdKJcsaMYBXKh7q3o4vFRy
PgacoiipkfYVSosQmxoC/b4PUeYCWa8Mkh0p6X+1aadI1PT58SZo374/NDAiu4aG
ao2FJgWCyYOCXRVPaDS2XDOUU3cogMJSk3M9c3xtEDI2yfzlKQ1TkoyYYG3WwcH7
5aEqGd5Iky27G2S8p16zoqyhHiC4Vq8fsWRRAnF/mVorNtpJC7BdI86VIzvKQlQ=
=sarB
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale arm64 device tree update for 4.21:
- Add device tree for LS1028A SoC and NXP FRWY & QDS boards support
based on this SoC.
- Add device tree for LX2160A SoC and NXP QDS & RDB boards support
based on this SoC.
- Add qdma devices for LS1043A and LS1046A SoC.
- Disable PCIe device by default in SoC device tree and let board level
device tree to enable as needed.
- Drop compatible string "snps,dw-pcie" from LayerScape PCIe devices to
avoid incorrect matching.
- Move fsl-mc device as a child node of soc node, and add missing
dma-ranges property for LS1088A SoC.
- Update LayerScape SoCs' cooling maps to include all devices affected
by individual trip points.
* tag 'imx-dt64-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls1046a: add qdma device tree nodes
arm64: dts: ls1043a: add qdma device tree nodes
arm64: dts: ls1088a: Add missing dma-ranges property
arm64: dts: ls1088a: Move fsl-mc node
arm64: dts: fsl: Add all CPUs in cooling maps
arm64: dts: Add support for NXP LS1028A SoC
arm64: dts: layerscape: removed compatible string "snps,dw-pcie"
arm64: dts: fsl: Add the status property disable PCIe
arm64: dts: ls1012a: Add FRWY-LS1012A board support
arm64: dts: add LX2160AQDS board support
arm64: dts: add LX2160ARDB board support
arm64: dts: add QorIQ LX2160A SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Update DWC3 hardware modules to Exynos5433 specific variant.
2. Update cooling maps to include all CPU devices in multiple DTS files.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAlwM920QHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD14IfD/4iMXDbb3VKcQyKFjepxhxtXsQ/cgOuDepG
enamjIVBkXFocbldVtEiKb2KM0j278It+8Q/vT5gvHESc/UL4nOJsmLUcaaIG6Jf
yqk3QDM3IzvKimT/UQFK871D6yMOYkLilaX9QL8RwdEtaBIEQNpT7OJORVjcxwbK
MXDyfO+B6qjcT4puulPv37/RWQEajN8qtTEwAlshvRoD8VPqIwU0sLKuMbKrU0wL
J4SZU6jPejwsB1xHJRE+Qq8aJVFCSdSd1vKYRObYfb1q0pBKg6npcEzEURl/G1OB
wcRfbT1Sg9u38a+qTSVMaEAgqfISB/mfeZbjJ/wJ/QaokAXoAxHhTX6M9BtWBAv2
iSRa9RR9I2dN7ZLeuq7SFxLsrglpnxundGUCg9ahmGLcnc+mUfM+ghNYYAIjsgLb
hUE8purXZMUJssvkOp6KjN9D5HW7nLvghNZ5ivQ99qIrPAwFZsZLIbcyrFKN8zCK
oa9gtSbDSOxOB43Uqh/93c7/1sCgJSuQgQnvDbV00ttQrApgHBFRBssaU9ByZz12
lBr7cAfEHAUrN+qvioOCWGp8jGBDbIoLeHm0KAV298TkLzVj1fnewrbcZjjew/+K
c398nGabl8AToLi6AHepCw6KPz8QWVX/mphw8hiUIWHMQfclSWMPLqEbdjdGHKqU
8LXDEUQZaQ==
=vgas
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM64 changes for v4.21
1. Update DWC3 hardware modules to Exynos5433 specific variant.
2. Update cooling maps to include all CPU devices in multiple DTS files.
* tag 'samsung-dt64-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add all CPUs in cooling maps
arm64: dts: exynos: Update DWC3 modules on Exynos5433 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
- complete the description of the clearfog-gt-8k board (Armada 8040
based board)
- declare eMMC on espressobin (Armada 3720 based board) which still
need to be enable by the bootloader as it is not present on all the
board.
- add a new version of the Macchiatobin (Armada 8040 based board): the
Single Shot (without the 10G 3310 PHYs).
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXAuF0wAKCRALBhiOFHI7
1Z0ZAJ41K0DWU/kNuQ8ZKTWhUFIVNNVxagCgnumdAUE7jxpgXu+WaVMNMXSJi+A=
=9Qkr
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.21-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.21 (part 1)
- complete the description of the clearfog-gt-8k board (Armada 8040
based board)
- declare eMMC on espressobin (Armada 3720 based board) which still
need to be enable by the bootloader as it is not present on all the
board.
- add a new version of the Macchiatobin (Armada 8040 based board): the
Single Shot (without the 10G 3310 PHYs).
* tag 'mvebu-dt64-4.21-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: describe mini-PCIe CON2 USB
arm64: dts: add support for Macchiatobin Single Shot board
arm64: dts: marvell: armada-37xx: Enable emmc on espressobin
arm64: dts: marvell: armada37xx: Add emmc/sdio pinctrl definition
arm64: dts: clearfog-gt-8k: enable mini-PCIe CON2 USB
arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal
arm64: dts: clearfog-gt-8k: fix USB regulator gpio polarity
Signed-off-by: Olof Johansson <olof@lixom.net>
* Switch to use dwc3-qcom glue driver on MSM8996
* Fix issue with xo clk name on MSM8998
* Add cooling maps on MSM8916
* Add UART nodes on SDM845
* Add camera subsystem support on MSM8996 and MSM8916
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EMri
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm ARM64 Updates for v4.21 Part 2
* Switch to use dwc3-qcom glue driver on MSM8996
* Fix issue with xo clk name on MSM8998
* Add cooling maps on MSM8916
* Add UART nodes on SDM845
* Add camera subsystem support on MSM8996 and MSM8916
* tag 'qcom-arm64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: msm8996: Use dwc3-qcom glue driver for USB
arm64: dts: qcom: msm8998: Fixup clock to use xo_board
arm64: dts: qcom: sdm845: Add UART nodes
arm64: dts: qcom: msm8996: Add CAMSS support
arm64: dts: qcom: msm8996: Add VFE SMMU node
arm64: dts: qcom: Add pinctrls for camera sensors
arm64: dts: qcom: Add Camera Control Interface pinctrls
arm64: dts: qcom: msm8916: Add CAMSS support
arm64: dts: qcom: msm8916: Add IOMMU sub-node for VFE context bank
arm64: dts: msm8916: Add all CPUs in cooling maps
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqGvQAKCRDj7w1vZxhR
xeObAQDZGMVjFjiWlC0jYjBQoCHMf1dlu6iPd4qe8h3GS1XUVQD/c8SJaMj5oLX1
HKjtqQD+sJRUQdcWlwAsqEEKyKUhfQs=
=aAr3
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
* tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a64: Fix up RTC device node and clock references
arm64: dts: allwinner: a64: Add Video Engine node
arm64: dts: allwinner: a64: Add support for the SRAM C1 section
arm64: dts: allwinner: a64: pinebook: enable power supplies
arm64: dts: allwinner: a64: sopine-baseboard: enable power supplies
arm64: dts: allwinner: axp803: add AC and battery power supplies
arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec
arm64: dts: allwinner: a64: enable sound on Pinebook
arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine
arm64: dts: allwinner: a64: add nodes necessary for analog sound support
arm64: dts: allwinner: h6: orangepi: Add device nodes for LEDs
arm64: dts: allwinner: h6: orangepi: Enable USB 2.0 host and OTG ports
arm64: dts: allwinner: h6: orangepi: Add board-wide 5V regulator
arm64: dts: allwinner: h6: fix EMAC compatible string sequence
arm64: dts: allwinner: a64: Add device node for Mali-400 GPU
dt-bindings: gpu: mali-utgard: Add compatible for A64 Mali
arm64: dts: allwinner: h6: enable USB2 on Pine H64
arm64: dts: allwinner: h6: add USB Vbus regulator for Pine H64
arm64: dts: allwinner: h6: add USB2-related device nodes
arm64: dts: allwinner: h6: Enable HDMI output on Pine H64 board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqFhwAKCRDj7w1vZxhR
xcQzAQDJu0dPrs3SQlWdDhOa0iFVp/7gmN4iRMxMScIIjrRUgAEAzmhUjQNNTNLc
OPF9XzMdT12rs2SAbk2XXtWH1hN8KQA=
=vSCG
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
* tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (84 commits)
ARM: dts: sunxi: Fix PMU compatible strings
ARM: dts: sun8i: r40: Add RTC device node
ARM: dts: sunxi: h3/h5: Fix up RTC device node and clock references
ARM: dts: sun8i: a23/a33: Fix up RTC device node
ARM: dts: sun8i: r40: Add clock accuracy for external oscillators
ARM: dts: sunxi: h3/h5: Add clock accuracy for external oscillators
ARM: dts: sun8i: a33: Drop audio codec oversampling rate to 128 fs
ARM: dts: sun8i: h3: Remove unnecessary reserved memory node
ARM: dts: sun8i: a33: Remove unnecessary reserved memory node
ARM: dts: suniv: Add device tree for Lichee Pi Nano
ARM: dts: suniv: add initial DTSI file for F1C100s
ARM: dts: axp81x: add AC power supply subnode
ARM: dts: sun8i: v3s: Remove skeleton and memory to avoid warnings
ARM: dts: sun8i: v3s: Provide default muxing for relevant controllers
ARM: dts: sun8i: v3s: Change pinctrl nodes to avoid warning
ARM: dts: sun8i: v3s: Change LRADC node names to avoid warnings
ARM: dts: sun8i: h3: Remove leading zeros from unit-addresses
ARM: dts: sun8i: BPI-M2M: Remove i2c nodes
ARM: dts: sun8i: a23/a33: Provide default muxing for relevant controllers
ARM: dts: sunxi: reference: Move the muxing back to the common DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add on-board LED support for Rock960 board based on the following
standard used by rest of the 96Boards:
green:user1 default-trigger: heartbeat
green:user2 default-trigger: mmc0/disk-activity(onboard-storage)
green:user3 default-trigger: mmc1 (SD-card)
green:user4 default-trigger: none, panic-indicator
yellow:wlan default-trigger: phy0tx
blue:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add on-board LED support for Ficus board based on the following
standard used by other 96Boards:
red:user1 default-trigger: heartbeat
red:user2 default-trigger: mmc0/disk-activity (onboard-storage)
red:user3 default-trigger: mmc1 (SD-card)
red:user4 default-trigger: none, panic-indicator
red:wlan default-trigger: phy0tx
red:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These changes add a bunch of features for Tegra194 and Tegra186, such as
wake events, on-die RTC, temperature sensors, HDA for audio over HDMI
and fan support on Jetson Xavier to allow cooling of the device.
-----BEGIN PGP SIGNATURE-----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=CDXO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
arm64: tegra: Device tree change for v4.21-rc1
These changes add a bunch of features for Tegra194 and Tegra186, such as
wake events, on-die RTC, temperature sensors, HDA for audio over HDMI
and fan support on Jetson Xavier to allow cooling of the device.
* tag 'tegra-for-4.21-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (29 commits)
arm64: tegra: Set reg property for display-hub on Tegra194
arm64: tegra: Set reg property for display-hub on Tegra186
arm64: dts: tegra186: Enable IOMMU for SDHCI
arm64: tegra: Enable HDA controller on Jetson TX1
arm64: tegra: Add CEC controller on Tegra194
arm64: tegra: Enable HDA on Jetson Xavier
arm64: tegra: Add HDA controller on Tegra194
arm64: tegra: Add CEC controller on Tegra186
arm64: tegra: Enable HDA on Jetson TX2
arm64: tegra: Add HDA controller on Tegra186
arm64: tegra: Add temperature sensor on P2888
arm64: tegra: Add gpio-keys on Jetson Xavier
arm64: tegra: Add AON GPIO controller on Tegra194
arm64: tegra: p2888: Enable on-die RTC
arm64: tegra: Add RTC support on Tegra194
arm64: tegra: Enable PMC wake events on Tegra194
arm64: tegra: p3310: Enable on-die RTC
arm64: tegra: Add RTC support on Tegra186
arm64: tegra: Enable PMC wake events on Tegra186
arm64: tegra: Fix power key interrupt type on Jetson TX2
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The usual batch; most of them are DT tweaks to fix misdescribed
hardware. Beyond that:
- A bugfix for MMP2 CPU detection, it's been there quite a while but
makes sense to fix now anyway.
- Some power management tweaks;
+ disabling of CPU idle power state on Marvell Armada 7K/8K (Macchiatobin et al)
+ Increase of minimum voltage on BananaPi M3
+ Tweak of power ramp time for DVFS on NXP/Freescale i.MX7SX
- A couple of MAINTAINER updates; MMP has a new volunteer to look after
it, and Mediatek adds a few keywords, IRC channel and wiki URL.
-----BEGIN PGP SIGNATURE-----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=gJxg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The usual batch; most of them are DT tweaks to fix misdescribed
hardware. Beyond that:
- A bugfix for MMP2 CPU detection, it's been there quite a while but
makes sense to fix now anyway.
- Some power management tweaks:
+ disabling of CPU idle power state on Marvell Armada 7K/8K
(Macchiatobin et al)
+ Increase of minimum voltage on BananaPi M3
+ Tweak of power ramp time for DVFS on NXP/Freescale i.MX7SX
- A couple of MAINTAINER updates:
+ MMP has a new volunteer to look after it
+ Mediatek adds a few keywords, IRC channel and wiki URL"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: realview: Fix some more duplicate regulator nodes
MAINTAINERS: update entry for MMP platform
ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dt
MAINTAINERS: mediatek: Update SoC entry
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
arm64: dts: mt7622: Drop the general purpose timer node
arm64: dts: mt7622: fix no more console output on BPI-R64 board
arm64: dts: mt7622: fix no more console output on rfb1
ARM: dts: sun8i: a83t: bananapi-m3: increase vcc-pd voltage to 3.3V
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adding CPU Idle state in the device tree for Armada 8040 seems to
breaks boot on some board, so let's revert it waiting for a better
solution.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXAuDHQAKCRALBhiOFHI7
1c27AJ0ddbDv84YeIAMDGt7ne2W0sjfaTACeIMt0Gk3yNonkTHSnfISzZ9p1Cu4=
=vrYg
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.20-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.20
Adding CPU Idle state in the device tree for Armada 8040 seems to
breaks boot on some board, so let's revert it waiting for a better
solution.
* tag 'mvebu-fixes-4.20-1' of git://git.infradead.org/linux-mvebu:
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
Signed-off-by: Olof Johansson <olof@lixom.net>
- Introduce protected-clock DT binding to fix breakage on qcom sdm845-mtp
boards where the qspi clks introduced this merge window cause the
firmware on those boards to take down the system if we try to read
the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data
-----BEGIN PGP SIGNATURE-----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=t1kp
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
Enable the USB3 peripheral that is wired to CON2 on the Clearfog GT-8K
board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add DT support for the Macchiatobin Single Shot board from SolidRun,
which is similar to the Double Shot board, but does not have the
10G 3310 PHYs - the two ethernet ports are instead connected directly
to the SFP+ cages.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The ESPRESSObin board has a emmc interface available on U11: declare it
and let the bootloader enable it if the emmc is present.
[gregory.clement@bootlin.com: disable the emmc by default]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
add the qDMA device tree nodes for LS1046A devices.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
add the qDMA device tree nodes for LS1043A devices.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1088A has a 48-bit address size so make sure that the
dma-ranges property reflects this.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fsl-mc node should sit under the soc node, so move it to
its proper location.
Fixes: ac7c9ff741 ("arm64: dts: ls1088a: add fsl-mc hardware resource manager node")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1028A contains two ARM v8 CortexA72 processor cores
with 32 KB L1-D cache and 48 KB L1-I cache
Features summary
Two 32-bit / 64-bit ARM v8 Cortex-A72 CPUs
- Arranged as single clusters of two cores sharing a 1 MB L2 cache
- Speed Up to 1.3 GHz
- Support for cluster power-gating.
Cache coherent interconnect (CCI-400)
- Hardware-managed data coherency
- Up to 400 MHz
32-bit DDR4 SDRAM memory controller with ECC
Two PCIe 3.0 controllers
One serial ATA (SATA 3.0) controller
Two high-speed USB 3.0 controllers with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1028A
SoC family:
- fsl-ls1028a.dtsi:
DTS-Include file for NXP LS1028A SoC.
- fsl-ls1028a-qds.dts:
DTS file for NXP LS1028A QDS board.
- fsl-ls1028a-rdb.dts:
DTS file for NXP LS1028A RDB board
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Removed the wrong compatible string "snps,dw-pcie", in case
match incorrect driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the status property disable the PCIe, the property will be enable
by bootloader.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1012A-FRWY is an ls1012a based SoC board.
Key features of this board are Micro SD, USB 3.0,
upto 1GB DDR, UART
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: feb3cbea09 ("ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage")
Fixes: 6d28d57751 ("ARM64: dts: meson-axg: fix ethernet stability issue")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the GPIO interrupt controller for the AXG SoCs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that the GPIO controller has been enabled also on AXG we can hook up
the GPIO interrupt for the PHY.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move from dwc3-of-simple to dwc3-qcom glue driver to
support peripheral mode which requires qscratch wrapper
programming on VBUS event.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch sets the msm8998 xo clock name back to xo_board. Recent
clock tree changes fixed the clock tree and the change to the xo name
is causing issues where msm8998 boards do not boot properly. Let's
change it back and leave the xo label on it.
Fixes: 634da3307b (arm64: dts: qcom: msm8998: correct xo clock name)
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The RTC module on the A64 was claimed to be the same as on the A31, when
in fact it is not. It is actually compatible to the H3's RTC. The A64's
RTC has some extra crypto-related registers which the H3's does not, but
the exact function of these is not clear.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The CEC controller found on Tegra194 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDA controller found on Tegra194 can be used for audio playback over
HDMI.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CEC controller found on Tegra186 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The rockpro64 does have hdmi support, so add the necessary
devicetree node to enable it.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockpro64 is not able boot if GPIO1_C1 pin is pulled high
before loading linux kernel.
In rockpro64 GPIO1_C1 pin is connected vdd_cpu_b regulator
VSEL pin. Pin should be pulled down in normal operation and
pulled high in suspend.
PMIC LDO_REG2 is connected to touch panel connector.
Rename regulator and set it to correct voltage.
PCIe power is controller by GPIO1_D0.
Schematics can be downloaded from:
http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Acked-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the Video Processing Unit node for the RK3399 SoC.
Also, fix the VPU IOMMU node, which was disabled and lacking
its power domain property.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the backlight device for the LVDS1 output, in preparation for panel
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds nodes for all possible UARTs to sdm845.dtsi. By default
only configure the RX/TX lines with pinctrl. Boards that use UARTs
with flow control can overwrite the configuration in the
<board>.dtsi.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the Video Engine node for the A64. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the description for the SRAM C1 section to the A64 device-tree.
Since there is no entry for this section in the A64 manual, the base
address and size were only verified to be consistent empirically.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds the Video Engine node for the H5. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the H5-specific system control node description to its device-tree
with support for the SRAM C1 section, that will be used by the video
codec node later on.
The CPU-side SRAM address was obtained empirically while the size was
taken from the documentation. They may not be entirely accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This reverts commit 8ed4636877.
This commit breaks boot on Armada 8K based systems. Reverting it makes
affected systems boot again.
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
