Shutdown of firmware framebuffer has a bunch of problems. Because
of this the framebuffer region might still be reserved even after
drm_fb_helper_remove_conflicting_pci_framebuffers() returned.
Don't consider pci_request_region() failure for the framebuffer
region as fatal error to workaround this issue.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20200313084152.2734-1-kraxel@redhat.com
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can fix the baco reset failure seen on Navi10.
And this should be a low risk fix as the same sequence
is already used for system suspend/resume.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The offset into the array was specified in bytes but should
be in terms of 32-bit words. Also prevent large reads that
would also cause a buffer overread.
v2: Read from correct offset from internal storage buffer.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
In dcn20_funcs and dcn21_funcs struct, the member ".dsc_pg_control = NULL"
should be removed due to .dsc_pg_control be assigned to dcn20_dsc_pg_control.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes: None
Cross-subsystem Changes: None
Core Changes: Fixed regressions introduced by commit cd82d82cbc
("drm/dp_mst: Add branch bandwidth validation to MST atomic check"),
which would cause us to:
* Calculate the available bandwidth on an MST topology incorrectly, and
as a result reject most display configurations that would try to enable
more then one sink on a topology
* Occasionally expose MST connectors to userspace before finishing
probing their PBN capabilities, resulting in us rejecting display
configurations because we assumed briefly that no bandwidth was
available
Driver Changes: None
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bf16ee577567beed91c86b7d9cda3ec2e8c50a71.camel@redhat.com
amd-drm-fixes-5.6-2020-03-11:
amdgpu:
- Update the display watermark bounding box for navi14
- Fix fetching vbios directly from rom on vega20/arcturus
- Navi and renoir watermark fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312020924.4161-1-alexander.deucher@amd.com
amd-drm-next-5.7-2020-03-10:
amdgpu:
- SR-IOV fixes
- Fix up fallout from drm load/unload callback removal
- Navi, renoir power management watermark fixes
- Refactor smu parameter handling
- Display FEC fixes
- Display DCC fixes
- HDCP fixes
- Add support for USB-C PD firmware updates
- Pollock detection fix
- Rework compute ring priority handling
- RAS fixes
- Misc cleanups
amdkfd:
- Consolidate more gfx config details in amdgpu
- Consolidate bo alloc flags
- Improve code comments
- SDMA MQD fixes
- Misc cleanups
gpu scheduler:
- Add suport for modifying the sched list
uapi:
- Clarify comments about GEM_CREATE flags that are not used by userspace.
The kernel driver has always prevented userspace from using these.
They are only used internally in the kernel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310212748.4519-1-alexander.deucher@amd.com
Sigh, this is mostly my fault for not giving commit cd82d82cbc
("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
enough scrutiny during review. The way we're checking bandwidth
limitations here is mostly wrong:
For starters, drm_dp_mst_atomic_check_bw_limit() determines the
pbn_limit of a branch by simply scanning each port on the current branch
device, then uses the last non-zero full_pbn value that it finds. It
then counts the sum of the PBN used on each branch device for that
level, and compares against the full_pbn value it found before.
This is wrong because ports can and will have different PBN limitations
on many hubs, especially since a number of DisplayPort hubs out there
will be clever and only use the smallest link rate required for each
downstream sink - potentially giving every port a different full_pbn
value depending on what link rate it's trained at. This means with our
current code, which max PBN value we end up with is not well defined.
Additionally, we also need to remember when checking bandwidth
limitations that the top-most device in any MST topology is a branch
device, not a port. This means that the first level of a topology
doesn't technically have a full_pbn value that needs to be checked.
Instead, we should assume that so long as our VCPI allocations fit we're
within the bandwidth limitations of the primary MSTB.
We do however, want to check full_pbn on every port including those of
the primary MSTB. However, it's important to keep in mind that this
value represents the minimum link rate /between a port's sink or mstb,
and the mstb itself/. A quick diagram to explain:
MSTB #1
/ \
/ \
Port #1 Port #2
full_pbn for Port #1 → | | ← full_pbn for Port #2
Sink #1 MSTB #2
|
etc...
Note that in the above diagram, the combined PBN from all VCPI
allocations on said hub should not exceed the full_pbn value of port #2,
and the display configuration on sink #1 should not exceed the full_pbn
value of port #1. However, port #1 and port #2 can otherwise consume as
much bandwidth as they want so long as their VCPI allocations still fit.
And finally - our current bandwidth checking code also makes the mistake
of not checking whether something is an end device or not before trying
to traverse down it.
So, let's fix it by rewriting our bandwidth checking helpers. We split
the function into one part for handling branches which simply adds up
the total PBN on each branch and returns it, and one for checking each
port to ensure we're not going over its PBN limit. Phew.
This should fix regressions seen, where we erroneously reject display
configurations due to thinking they're going over our bandwidth limits
when they're not.
Changes since v1:
* Took an even closer look at how PBN limitations are supposed to be
handled, and did some experimenting with Sean Paul. Ended up rewriting
these helpers again, but this time they should actually be correct!
Changes since v2:
* Small indenting fix
* Fix pbn_used check in drm_dp_mst_atomic_check_port_bw_limit()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Sean Paul <seanpaul@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309210131.1497545-1-lyude@redhat.com
We used to punt off reprobing path resources to the link address probe
work, but now that we handle CSNs asynchronously from the driver's HPD
handling we can do whatever the heck we want from the CSN!
So, reprobe the path resources from drm_dp_mst_handle_conn_stat(). Also,
get rid of the path resource reprobing code in
drm_dp_check_and_send_link_address() since it's needlessly complicated
when we already reprobe path resources from
drm_dp_handle_link_address_port(). And finally, teach
drm_dp_send_enum_path_resources() to return 1 on PBN changes so we know
if we need to send another hotplug or not.
This fixes issues where we've indicated to userspace that a port has
just been connected, before we actually probed it's available PBN -
something that results in unexpected atomic check failures.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-4-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
DisplayPort specifications are fun. For a while, it's been really
unclear to us what available_pbn actually does. There's a somewhat vague
explanation in the DisplayPort spec (starting from 1.2) that partially
explains it:
The minimum payload bandwidth number supported by the path. Each node
updates this number with its available payload bandwidth number if its
payload bandwidth number is less than that in the Message Transaction
reply.
So, it sounds like available_pbn represents the smallest link rate in
use between the source and the branch device. Cool, so full_pbn is just
the highest possible PBN that the branch device supports right?
Well, we assumed that for quite a while until Sean Paul noticed that on
some MST hubs, available_pbn will actually get set to 0 whenever there's
any active payloads on the respective branch device. This caused quite a
bit of confusion since clearing the payload ID table would end up fixing
the available_pbn value.
So, we just went with that until commit cd82d82cbc ("drm/dp_mst: Add
branch bandwidth validation to MST atomic check") started breaking
people's setups due to us getting erroneous available_pbn values. So, we
did some more digging and got confused until we finally looked at the
definition for full_pbn:
The bandwidth of the link at the trained link rate and lane count
between the DP Source device and the DP Sink device with no time slots
allocated to VC Payloads, represented as a Payload Bandwidth Number. As
with the Available_Payload_Bandwidth_Number, this number is determined
by the link with the lowest lane count and link rate.
That's what we get for not reading specs closely enough, hehe. So, since
full_pbn is definitely what we want for doing bandwidth restriction
checks - let's start using that instead and ignore available_pbn
entirely.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
It's already prefixed by dp_mst, so we don't really need to repeat
ourselves here. One of the changes I should have picked up originally
when reviewing MST DSC support.
There should be no functional changes here
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <seanpaul@google.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-2-lyude@redhat.com
During driver unload, we have many asserts that we have released our
bookkeeping structs and are idle. In some cases, these struct are
protected by RCU and we do not release them until after an RCU grace
period.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 130a95e909 ("drm/i915/gem: Consolidate ctx->engines[] release")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312115307.16460-1-chris@chris-wilson.co.uk
Since the relocations are no longer performed under a global
struct_mutex, or any other lock, that is also held by pagefault handlers,
we can relax and allow our fast path to take a fault. As we no longer
need to abort the fast path for lock avoidance, we no longer need the
slow path handling at all.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311160310.26711-1-chris@chris-wilson.co.uk
I noticed that there is a prototype for vmw_fifo_ping_host_locked() but
no function. Then I looked further and noticed more functions which are
not used anymore or functions protoypes which remained after the
function was removed.
Remove unused function (prototypes).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
vmw_fifo_ping_host() disables preemption around a test and a register
write via vmw_write(). The write function acquires a spinlock_t typed
lock which is not allowed in a preempt_disable()ed section on
PREEMPT_RT. This has been reported in the bugzilla.
It has been explained by Thomas Hellstrom that this preempt_disable()ed
section is not required for correctness.
Remove the preempt_disable() section.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206591
Link: https://lkml.kernel.org/r/0b5e1c65d89951de993deab06d1d197b40fd67aa.camel@vmware.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Allow super long OpenCL workloads which cannot be preempted within
the default timeout to run out of the box.
v2:
* Make it stick out more and apply only to RCS. (Chris)
v3:
* Mention platform override in kconfig. (Joonas)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Mrozek <michal.mrozek@intel.com>
Cc: <stable@vger.kernel.org> # v5.6+
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michal Mrozek <Michal.mrozek@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312115748.29970-1-tvrtko.ursulin@linux.intel.com
TTM doesn't yet fully support mapping of DMA memory when SEV is active,
so in that case, refuse DMA operation. For guest-backed object operation
this means 3D acceleration will be disabled. For host-backed, VRAM will be
used for data transfer between the guest and the device.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
When we refuse DMA from system pages for whatever reason, we don't
handle that correctly when guest-backed objects was enabled.
Since guest-backed objects by definition require DMA to and from
system pages, disable all functionality that relies on them.
That basically amounts to 3D acceleration and screen targets.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Runtime PM and RGB output need to be released when host1x client
registration fails. The releasing is missed in the code, let's correct it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The devm_platform_ioremap_resource() helper replaces few lines of a
boilerplate code with a single line, making code to look cleaner a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When applying the context-barrier, we only care about the current
engines, as the next set of engines will be naturally after the barrier.
So we can skip holding the ctx->engines_mutex while constructing the
request by taking a sneaky reference to the i915_gem_engines instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311221739.30375-2-chris@chris-wilson.co.uk
If the cacheline may still be busy, atomically mark it for future
release, and only if we can determine that it will never be used again,
immediately free it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392
Fixes: ebece75392 ("drm/i915: Keep timeline HWSP allocated until idle across the system")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk
(cherry picked from commit 2d4bd971f5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If we stop filling the ELSP due to an incompatible virtual engine
request, check if we should enable the timeslice on behalf of the queue.
This fixes the case where we are inspecting the last->next element when
we know that the last element is the last request in the execution queue,
and so decided we did not need to enable timeslicing despite the intent
to do so!
Fixes: 8ee36e048c ("drm/i915/execlists: Minimalistic timeslicing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk
(cherry picked from commit 3df2deed41)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The alignment is u64, and yet is_power_of_2() assumes unsigned long,
which might give different results between 32b and 64b kernel.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit 2920516b2f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
added the support on CFL. The vgpu emulation hotplug support on CFL was
supposed to be included in that patch. Without the vgpu emulation
hotplug support, the dma-buf based display gives us a blur face.
So fix this issue by adding the vgpu emulation hotplug support on CFL.
Fixes: c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200227010041.32248-1-tina.zhang@intel.com
(cherry picked from commit 135dde8853)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Requests within a timeline are ordered by that timeline, so awaiting for
the start of a request within the timeline is a no-op. This used to work
by falling out of the mutex_trylock() as the signaler and waiter had the
same timeline and not returning an error.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305134822.2750496-1-chris@chris-wilson.co.uk
(cherry picked from commit ab7a69020f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the inverted test to emit the wait on the end of the previous
request if we /haven't/ already.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305104210.2619967-1-chris@chris-wilson.co.uk
(cherry picked from commit 07e9c59d63)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm_dp_mst_topology_mgr_cbs.destroy_connector callbacks are identical
amongst every driver and don't do anything other than cleaning up the
connector((drm_connector_unregister()/drm_connector_put())) except for
amdgpu_dm driver where some amdgpu_dm specific code in there.
This connector cleaning up is now being handled in the drm core so
driver destroy_connector callbacks are not needed (except for
amdgpu_dm) hence remove them.
Removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .destroy_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-6-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_topology_mgr_cbs.destroy_connector callbacks are identical
amongst every driver and don't do anything other than cleaning up the
connector (drm_connector_unregister()/drm_connector_put()) except for
amdgpu_dm driver where some amdgpu_dm specific code in there which I
an not sure if it should stay or not.
Create and use a helper which calls driver's destroy_connector hook if
available otherwise does cleanup internally.
This is the step towards removing identical hooks from every driver.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-5-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_port_add_connector() directly calls the
drm_connector_register() now and
drm_dp_mst_topology_mgr_cbs.register_connector callback is not getting
called anymore.
Hence remove all drm_dp_mst_topology_mgr_cbs.register_connector
callbacks.
This is the preparatory step for removing the
drm_dp_mst_topology_mgr_cbs.register_connector callback hook.
The removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .register_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-3-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_topology_mgr_cbs.register_connector callbacks are literally
identical amongst every driver and don't do anything other than
calling drm_connector_register(). Hence call drm_connector_register()
directly instead of a callback.
This is the preparatory step for removing the
drm_dp_mst_topology_mgr_cbs.register_connector callback hook.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-2-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Adaptive Sync is a VESA feature so add a DRM core helper to parse
the EDID's detailed descritors to obtain the adaptive sync monitor range.
Store this info as part fo drm_display_info so it can be used
across all drivers.
This part of the code is stripped out of amdgpu's function
amdgpu_dm_update_freesync_caps() to make it generic and be used
across all DRM drivers
v6:
* Call it monitor_range (Ville)
v5:
* Use the renamed flags
v4:
* Use is_display_descriptor() (Ville)
* Name the monitor range flags (Ville)
v3:
* Remove the edid parsing restriction for just DP (Nicholas)
* Use drm_for_each_detailed_block (Ville)
* Make the drm_get_adaptive_sync_range function static (Harry, Jani)
v2:
* Change vmin and vmax to use u8 (Ville)
* Dont store pixel clock since that is just a max dotclock
and not related to VRR mode (Manasi)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310231651.13841-2-manasi.d.navare@intel.com
Gen12 hardware supports HDMI audio pixel clocks of 296.7/297Mhz
and 593.4/594Mhz. Add the missing rates and add logic to ignore
them if running on older hardware.
Bspec: 49333
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310162338.9387-1-kai.vehmanen@linux.intel.com
The currently listed dotclock disagrees with the currently
listed vrefresh rate. Change the dotclock to match the vrefresh.
Someone tell me which (if either) of the dotclock or vreresh is
correct?
Cc: Adam Ford <aford173@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302203452.17977-22-ville.syrjala@linux.intel.com
Reviewed-by: Adam Ford <aford173@gmail.com>
The currently listed dotclocks disagree with the currently
listed vrefresh rates. Change the dotclocks to match the vrefresh.
Someone tell me which (if either) of the dotclock or vreresh is
correct?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302203452.17977-9-ville.syrjala@linux.intel.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The currently listed dotclock disagrees with the currently
listed vrefresh rate. Change the dotclock to match the vrefresh.
Someone tell me which (if either) of the dotclock or vreresh is
correct?
Cc: Heiko Schocher <hs@denx.de>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302203452.17977-7-ville.syrjala@linux.intel.com
Reviewed-by: Heiko Schocher <hs@denx.de>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311073540.7108-1-tiwai@suse.de
Record the initial active element we use when building the next ELSP
submission, so that we can compare against it latter to see if there's
no change.
Fixes: 44d0a9c05b ("drm/i915/execlists: Skip redundant resubmission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311092624.10012-2-chris@chris-wilson.co.uk
Avoid angering kcsan by serialising the read of the pm_events with the
write in rps_disable_interrupts.
[ 6268.713419] BUG: KCSAN: data-race in intel_rps_park [i915] / rps_work [i915]
[ 6268.713437]
[ 6268.713449] write to 0xffff8881eda8efac of 4 bytes by task 1127 on cpu 3:
[ 6268.713680] intel_rps_park+0x136/0x260 [i915]
[ 6268.713905] __gt_park+0x61/0xa0 [i915]
[ 6268.714128] ____intel_wakeref_put_last+0x42/0x90 [i915]
[ 6268.714352] __intel_wakeref_put_work+0xd3/0xf0 [i915]
[ 6268.714369] process_one_work+0x3b1/0x690
[ 6268.714384] worker_thread+0x80/0x670
[ 6268.714398] kthread+0x19a/0x1e0
[ 6268.714412] ret_from_fork+0x1f/0x30
[ 6268.714423]
[ 6268.714435] read to 0xffff8881eda8efac of 4 bytes by task 950 on cpu 2:
[ 6268.714664] rps_work+0xc2/0x680 [i915]
[ 6268.714679] process_one_work+0x3b1/0x690
[ 6268.714693] worker_thread+0x80/0x670
[ 6268.714707] kthread+0x19a/0x1e0
[ 6268.714720] ret_from_fork+0x1f/0x30
v2: Mark all reads and writes of rpm->pm_events.
The flow of enabling/disabling rps is stronly ordered, so the writes and
interrupt generation are also strongly ordered -- just this may not be
visible to the compiler, so provide annotations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311092624.10012-1-chris@chris-wilson.co.uk
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/357174/
Signed-off-by: Christian König <christian.koenig@amd.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311073256.6535-1-tiwai@suse.de
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hotplug.c.
In some cases, this involves extracting the drm_i915_private pointer from
the drm_device struct to be used in the logging macros.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3dfda89ab4a234f299ada77abd14163cef3f8bd4.1583766715.git.jani.nikula@intel.com
The assert sometimes incorrectly triggers when pinned BOs are destroyed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Link: https://patchwork.freedesktop.org/patch/356737/
The two files have been duplicated under the gt/ subdir and since there
are not apparent users looking for them at the old location lets simply
remove them and duplicated code.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310164733.26487-1-tvrtko.ursulin@linux.intel.com
rockchip_drm_endpoint_is_subdriver() may also return error codes.
For example if the target-node is in the disabled state, so no
platform-device is getting created for it.
In that case current code would count that as external rgb device,
which in turn would make probing the rockchip-drm device fail.
So only count the target as rgb device if the function actually
returns 0.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121224828.4070067-1-heiko@sntech.de
As a virtual engine may change the rq->engine to point to the active
request in flight, we need to warn the compiler that an active request's
engine is volatile.
[ 95.017686] write (marked) to 0xffff8881e8386b10 of 8 bytes by interrupt on cpu 2:
[ 95.018123] execlists_dequeue+0x762/0x2150 [i915]
[ 95.018539] __execlists_submission_tasklet+0x48/0x60 [i915]
[ 95.018955] execlists_submission_tasklet+0xd3/0x170 [i915]
[ 95.018986] tasklet_action_common.isra.0+0x42/0xa0
[ 95.019016] __do_softirq+0xd7/0x2cd
[ 95.019043] irq_exit+0xbe/0xe0
[ 95.019068] irq_work_interrupt+0xf/0x20
[ 95.019491] i915_request_retire+0x2c5/0x670 [i915]
[ 95.019937] retire_requests+0xa1/0xf0 [i915]
[ 95.020348] engine_retire+0xa1/0xe0 [i915]
[ 95.020376] process_one_work+0x3b1/0x690
[ 95.020403] worker_thread+0x80/0x670
[ 95.020429] kthread+0x19a/0x1e0
[ 95.020454] ret_from_fork+0x1f/0x30
[ 95.020476]
[ 95.020498] read to 0xffff8881e8386b10 of 8 bytes by task 8909 on cpu 3:
[ 95.020918] __i915_request_commit+0x177/0x220 [i915]
[ 95.021329] i915_gem_do_execbuffer+0x38c4/0x4e50 [i915]
[ 95.021750] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[ 95.021784] drm_ioctl_kernel+0xe4/0x120
[ 95.021809] drm_ioctl+0x297/0x4c7
[ 95.021832] ksys_ioctl+0x89/0xb0
[ 95.021865] __x64_sys_ioctl+0x42/0x60
[ 95.021901] do_syscall_64+0x6e/0x2c0
[ 95.021927] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310142403.5953-1-chris@chris-wilson.co.uk
When being used across multiple real engines inside a virtual engine,
the intel_context.inflight is updated atomically, and so we must
annotate the racy read from outside the owning context.
[11142.482846] BUG: KCSAN: data-race in __execlists_submission_tasklet [i915] / __execlists_submission_tasklet [i915]
[11142.482867]
[11142.482878] write (marked) to 0xffff8881f257b5e0 of 8 bytes by interrupt on cpu 2:
[11142.483107] __execlists_submission_tasklet+0x1d33/0x2120 [i915]
[11142.483336] execlists_submission_tasklet+0xd3/0x170 [i915]
[11142.483355] tasklet_action_common.isra.0+0x42/0xa0
[11142.483371] __do_softirq+0xd7/0x2cd
[11142.483384] irq_exit+0xbe/0xe0
[11142.483401] do_IRQ+0x51/0x100
[11142.483424] ret_from_intr+0x0/0x1c
[11142.483446] do_idle+0x133/0x1f0
[11142.483465] cpu_startup_entry+0x14/0x16
[11142.483483] start_secondary+0x120/0x180
[11142.483498] secondary_startup_64+0xa4/0xb0
[11142.483512]
[11142.483528] read to 0xffff8881f257b5e0 of 8 bytes by interrupt on cpu 1:
[11142.483755] __execlists_submission_tasklet+0x14e/0x2120 [i915]
[11142.483981] execlists_submission_tasklet+0xd3/0x170 [i915]
[11142.483999] tasklet_action_common.isra.0+0x42/0xa0
[11142.484014] __do_softirq+0xd7/0x2cd
[11142.484028] do_softirq_own_stack+0x2a/0x40
[11142.484046] do_softirq.part.0+0x26/0x30
[11142.484071] __local_bh_enable_ip+0x46/0x50
[11142.484299] i915_gem_do_execbuffer+0x39c1/0x4e50 [i915]
[11142.484528] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[11142.484546] drm_ioctl_kernel+0xe4/0x120
[11142.484559] drm_ioctl+0x297/0x4c7
[11142.484572] ksys_ioctl+0x89/0xb0
[11142.484586] __x64_sys_ioctl+0x42/0x60
[11142.484610] do_syscall_64+0x6e/0x2c0
[11142.484627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310141320.24149-1-chris@chris-wilson.co.uk
dc to pplib interface is changed for navi1x, renoir.
display_config_changed is not called by dc anymore.
smu_write_watermarks_table is not executed for navi1x, renoir
during boot up.
solution: call smu_write_watermarks_table just after dc pass
watermark clock settings to pplib
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platforms without fences don't have FBC host tracking and those
registers are marked as reserved in those platforms.
v2: checking num_fences to write to FBC fence registers (Ville)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306185833.53984-2-jose.souza@intel.com
i915 can enable aux device nodes for DP MST by calling
drm_dp_mst_connector_late_register()/
drm_dp_mst_connector_early_unregister(),
so let's hook that up.
Changes since v1:
* Call intel_connector_register/unregister() from
intel_dp_mst_connector_late_register/unregister() so we don't lose
error injection - Ville Syrjälä
Changes since v2:
* Don't forget to clean up if intel_connector_register() fails - Ville
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310195122.1590925-1-lyude@redhat.com
Some framework test will fail if enable runpm on Vega10.
Disable it untill issue fixed.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Tested-by: Kyle Chen <Kyle.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
and remove each ras IP's own debugfs creation
this is required to fix ras when the driver does not use the drm load
and unload callbacks due to ordering issues with the drm device node.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
centralize all debugfs creation in one place for ras
this is required to fix ras when the driver does not use the drm load
and unload callbacks due to ordering issues with the drm device node.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There will be a coverity warning because min and max are both unsigned.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only kernel bo has kfd eviction fence.
This warning is to give a notice that kfd only remove eviction fence on
individual bos.
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ALLOC_MEM_FLAGS_* used are the same as the KFD_IOC_ALLOC_MEM_FLAGS_*,
but they are interweavedly used in kernel driver, resulting in bad
readability. For example, KFD_IOC_ALLOC_MEM_FLAGS_COHERENT is not
referenced in kernel, and it functions implicitly in kernel through
ALLOC_MEM_FLAGS_COHERENT, causing unnecessary confusion.
Replace all occurrences of ALLOC_MEM_FLAGS_* with
KFD_IOC_ALLOC_MEM_FLAGS_* to solve the problem.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
People are inclined to think of the previous pr_warn message as an
error, so use pre_debug instead.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there are no high priority compute queues available then set normal
priority sched array to compute_prio_sched[AMDGPU_GFX_PIPE_PRIO_HIGH]
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We actually expect this to return a 0 on success, or negative error code
on failure. In order to do that, we check whether or not we managed to
write the whole GUID and then return 0 if so, otherwise return a
negative error code. Also, let's add an error message here so it's a
little more obvious when this fails in the middle of a link address
probe.
This should fix issues with certain MST hubs seemingly stopping for no
reason in the middle of the link address probe process.
Fixes: cb897542c6 ("drm/dp_mst: Fix W=1 warnings")
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Noticed this while having some problems with hubs sometimes not being
detected on the first plug. Every single dpcd read or write function
returns the number of bytes transferred on success or a negative error
code, except apparently for drm_dp_mst_dpcd_write() - which returns 0 on
success.
There's not really any good reason for this difference that I can tell,
and having the two functions give differing behavior means that
drm_dp_dpcd_write() will end up returning 0 on success for MST devices,
but the number of bytes transferred for everything else.
So, fix that and update the kernel doc.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 2f221a5efe ("drm/dp_mst: Add MST support to DP DPCD R/W functions")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-2-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The currently listed dotclock disagrees with the currently
listed vrefresh rate. Change the dotclock to match the vrefresh.
There are two variants of the COM37H3M panel.
The older one's COM37H3M05DTC data sheet specifies:
MIN TYP MAX
CLK frequency fCLK -- 22.4 26.3 MHz (in VGA mode)
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv -- 650 -- H
HSYNC frequency fHSYNC -- 39.3 -- kHz
HSYNC cycle time th -- 570 -- CLK
The newer one's COM37H3M99DTC data sheet says:
MIN TYP MAX
CLK frequency fCLK 18 19.8 27 MHz
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv 646 650 700 H
HSYNC frequency fHSYNC -- 39.0 50.0 kHz
HSYNC cycle time th 504 508 630 CLK
So we choose a parameter set that lies within the specs
of both variants. We start at .vrefresh = 60,
choose .htotal = 570 and .vtotal = 650 and end up
in a clock of 22.230 MHz.
Reported-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e63a0533ad5b5142373437ef758aedbdb716152d.1583826198.git.hns@goldelico.com
Always wait on the start of the signaler request to reduce the problem
of dequeueing the bonded pair too early -- we want both payloads to
start at the same time, with no latency, and yet still allow others to
make full use of the slack in the system. This reduce the amount of time
we spend waiting on the semaphore used to synchronise the start of the
bonded payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-3-chris@chris-wilson.co.uk
In Pete Goodliffe words, "You can improve a system by adding new code. You
can also improve a system by removing code" - In this case, commit
"202b52b7fbf70" added new code to initialize end of the node. So, there
is no need for duplicated initialization, and this patch simply removes it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309151156.25040-1-akeem.g.abodunrin@intel.com
This patch adds support for the YUV420 output from the Amlogic Meson SoCs
Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch enables the bridge bus format negociation, and handles
the YUV420 case if selected by the negociation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-12-narmstrong@baylibre.com
This patch adds clocking support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch adds the TMDS PHY clock value in all the video clock setup
in order to better support these specific uses cases and switch
to the Common Clock framework for clocks handling in the future.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-11-narmstrong@baylibre.com
This patch adds encoding support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
In addition if pixel stream down-sampling, the Y Cb Cr components must
also be mapped differently to align with the HDMI2.0 specifications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-10-narmstrong@baylibre.com
To allow using formats from negotiation, stop enforcing input_bus_format
in the private dw-plat-data struct.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-9-narmstrong@baylibre.com
Switch the dw-hdmi driver to drm_bridge_funcs by implementing a new local
bridge, connecting it to the dw-hdmi bridge, then implement the
atomic_get_input_bus_fmts/atomic_get_output_bus_fmts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-8-narmstrong@baylibre.com
Before switching to bridge funcs, make sure drm_display_mode is passed
as const to the venc functions.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-7-narmstrong@baylibre.com
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
The ROMC_INDEX/DATA offset was changed to e4/e5 since
from smuio_v11 (vega20/arcturus).
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Tested-by: Candice Li <Candice.Li@amd.com>
Reviewed-by: Candice Li <Candice.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gmbus/aux may be clocked by cdclk, thus we should make sure no
transfers are ongoing while the cdclk frequency is being changed.
We do that by simply grabbing all the gmbus/aux mutexes. No one
else should be holding any more than one of those at a time so
the lock ordering here shouldn't matter.
v2: Use mutex_lock_nest_lock() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302174442.5803-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The low level read_lut() functions don't need the entire crtc state
as they know exactly what they're reading. Just need to pass in the
crtc to get at the pipe. This now neatly mirrors the load_lut()
direction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-10-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
PIPEGCMAX is a 11.6 (or 1.16 if you will) value. Ie. it can
represent a value of 1.0 when the maximum we can store in the
software LUT is 0.ffff. Clamp the value so that it gets
saturated to the max the uapi supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-9-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
A variable called 'i' having an unsigned type is just looking for
trouble, and using a sized type generally makes no sense either.
Change all of them to just plain old int. And do the same for some
'lut_size' variables which generally provide the loop end codition
for 'i'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-7-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Only load the CGM CSC based on the cgm_mode bit like we
do with the gamma/degamma LUTs. And make the function
naming and arguments consistent as well.
TODO: the code to convert the coefficients look totally
bogus. IIRC CHV uses two's complement format but the code
certainly doesn't generate that, so probably negative
coefficients are totally busted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-2-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During i915_request_retire() we decouple the i915_request.hwsp_seqno
from the intel_timeline so that it may be freed before the request is
released. However, we need to warn the compiler that the pointer may
update under its nose.
[ 171.438899] BUG: KCSAN: data-race in i915_request_await_dma_fence [i915] / i915_request_retire [i915]
[ 171.438920]
[ 171.438932] write to 0xffff8881e7e28ce0 of 8 bytes by task 148 on cpu 2:
[ 171.439174] i915_request_retire+0x1ea/0x660 [i915]
[ 171.439408] retire_requests+0x7a/0xd0 [i915]
[ 171.439640] engine_retire+0xa1/0xe0 [i915]
[ 171.439657] process_one_work+0x3b1/0x690
[ 171.439671] worker_thread+0x80/0x670
[ 171.439685] kthread+0x19a/0x1e0
[ 171.439701] ret_from_fork+0x1f/0x30
[ 171.439721]
[ 171.439739] read to 0xffff8881e7e28ce0 of 8 bytes by task 696 on cpu 1:
[ 171.439990] i915_request_await_dma_fence+0x162/0x520 [i915]
[ 171.440230] i915_request_await_object+0x2fe/0x470 [i915]
[ 171.440467] i915_gem_do_execbuffer+0x45dc/0x4c20 [i915]
[ 171.440704] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[ 171.440722] drm_ioctl_kernel+0xe4/0x120
[ 171.440736] drm_ioctl+0x297/0x4c7
[ 171.440750] ksys_ioctl+0x89/0xb0
[ 171.440766] __x64_sys_ioctl+0x42/0x60
[ 171.440788] do_syscall_64+0x6e/0x2c0
[ 171.440802] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309110934.868-1-chris@chris-wilson.co.uk
AMDGPU statically sets priority for compute queues
at initialization so remove all the functions
responsible for changing compute queue priority dynamically.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Switch to appropriate sched list for an entity on priority override.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement drm_sched_entity_modify_sched() which modifies existing
sched_list with a different one. This is going to be helpful when
userspace changes priority of a ctx/entity then the driver can switch
to the corresponding HW scheduler list for that priority.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were changing compute ring priority while rings were being used
before every job submission which is not recommended. This patch
sets compute queue priority at mqd initialization for gfx8, gfx9 and
gfx10.
Policy: make queue 0 of each pipe as high priority compute queue
High/normal priority compute sched lists are generated from set of high/normal
priority compute queues. At context creation, entity of compute queue
get a sched list from high or normal priority depending on ctx->priority
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem Description:
Currently we are checking internal fused rev id with pci rev id. However, fused
internal rev id is the same on all raven2 parts (in which Dali and Pollock were
based on too), thus Pollock detection fails
Fix:
use the pci rev to preform the detection for bandwidth calculations.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the pci revision id rather than the asic silicon revision id.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CRTC in DPMS state off calls for low power state entry.
Support both atomic mode setting and pre-atomic mode setting.
v2: move comment
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dpp2_get_optimal_number_of_taps function is never used. Removing
just for code cleaning up.
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FEC capability query should not be affected by debugging decision on
whether to disable FEC. We should not determine if display supports FEC
by checking debug option.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In HDCP Uninitialzed State, a CPIRQ event would cause log output
internal policy error because the CPIRQ event is not recognized as
unexpected event.
[how]
CPIRQ is issued in HDCP uninitialized state is unexpected. We should
set unexpected event flag in event ctx.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some RX doesn't like us to read rx id list upto max rx id list size. As
discussed, we decided to read rx id list based on device count.
[how]
According to HDCP specs the actual size of rx id list is calculated as
rx id list size = 2+3+16+5*device_count. We will read 16 bytes at a
time until it reached or exceeded rx id list size.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
Need debug options to control lightl/deep sleep
[How]
Add registry for memory power control
Signed-off-by: Braden Bakker <Braden.Bakker@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is possible even if sink signal is MST but driver enables SST stream.
We should not determine if we should do MST authentication based on
sink's capability.
Instead we should determine whether to do MST authentication based on
what we have enabled in stream.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
So the values of stay count and bstatus can be easily viewed during
debugging.
[How]
Add stay count and bstatus values to be outputted in HDCP log
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The UNSLICE_UNIT_LEVEL_CLKGATE and UNSLICE_UNIT_LEVEL_CLKGATE2 registers
that we update in a few engine workarounds are not masked registers
(i.e., we don't have to write a mask bit in the top 16 bits when
updating one of the lower 16 bits). As such, these workarounds should
be applied via wa_write_or() rather than wa_masked_en()
v2:
- Rebase
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
References: https://github.com/ClangBuiltLinux/linux/issues/918
Fixes: 50148a25f8 ("drm/i915/tgl: Move and restrict Wa_1408615072")
Fixes: 3551ff9287 ("drm/i915/gen11: Moving WAs to rcs_engine_wa_init()")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306171139.1414649-1-matthew.d.roper@intel.com
Fix the following kerneldoc warning and while at it also the doc for the
corresponding vfunc hook.
$ make htmldocs 2>&1 > /dev/null | grep i915
./drivers/gpu/drm/i915/display/intel_dpll_mgr.h:285: warning: Function parameter or member 'get_freq' not described in 'intel_shared_dpll_funcs'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304150918.25473-1-imre.deak@intel.com
A resource will be a shmem based resource or a (planned)
vram based resource, so it makes sense to factor out common fields
(resource handle, dumb).
v2: move mapped field to shmem object
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20200305013212.130640-1-gurchetansingh@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Pull the drm_pci_agp_init() underneath the legacy ifdeffry alongside its
only caller.
The diff chooses it to so it by moving drm_pci_agp_destroy earlier, but
the important bit is moving the #ifdef earlier before drm_pci_agp_init.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307093702.2269-1-chris@chris-wilson.co.uk
This reverts commit 0f9cdd743f.
The interface of the panel is LVDS, not parallel.
The color depth is RGB888, not RGB565.
The panel has additional features, making it not so simple.
The only user (upstream) of this panel is appropriately using panel-lvds.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305130536.26011-1-peda@axentia.se
Be sure to wait for the vma to be in place before we tell the GPU to
execute from the wa batch. Since initialisation is mostly synchronous
(or rather at some point during start up we will need to sync anyway),
we can affort to do an explicit i915_vma_sync() during wa batch
construction rather than check for a required await on every context
switch. (We don't expect to change the wa bb at run time so paying the
cost once up front seems preferrable.)
Fixes: ee2413eeed ("drm/i915: Add mechanism to submit a context WA on ring submission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307122425.29114-1-chris@chris-wilson.co.uk
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305105558.GA19124@embeddedor
If the cacheline may still be busy, atomically mark it for future
release, and only if we can determine that it will never be used again,
immediately free it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392
Fixes: ebece75392 ("drm/i915: Keep timeline HWSP allocated until idle across the system")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk
If we stop filling the ELSP due to an incompatible virtual engine
request, check if we should enable the timeslice on behalf of the queue.
This fixes the case where we are inspecting the last->next element when
we know that the last element is the last request in the execution queue,
and so decided we did not need to enable timeslicing despite the intent
to do so!
Fixes: 8ee36e048c ("drm/i915/execlists: Minimalistic timeslicing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk
Due to the ordering of cmpxchg()/dma_fence_signal() inside node_retire(),
we must also use the xchg() as our primary memory barrier to flush the
outstanding callbacks after expected completion of the i915_active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-1-chris@chris-wilson.co.uk
This workaround is to disable FF DOP Clock gating. The fix
in B0 was backed out due to timing reasons and decided to
be made permanent.
Bspec: 52890
Signed-off-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305181204.28856-1-swathi.dhanavanthri@intel.com
On some platforms such as Elkhart Lake, although we may use DDI D
to drive a connector, we have to use PHY A (Combo Phy PORT A) to
detect the hotplug interrupts as per the spec because there is no
one-to-one mapping between DDIs and PHYs. Therefore, use the
function intel_port_to_phy() which contains the logic for such
mapping(s) to find the correct hpd_pin.
This change should not affect other platforms as there is always
a one-to-one mapping between DDIs and PHYs.
v2:
- Convert the case statements to use PHYs instead of PORTs (Jani)
v3:
- Refactor the function to reduce the number of return statements by
lumping all the case statements together except PHY_F which needs
special handling (Jose)
v4:
- Add a comment describing how the HPD pin value associated with any
port can be retrieved using port or phy enum value. (Jani)
v5:
- Use case ranges instead of individual labels and also normalize the
return statement by adding -PHY_A to the expression (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304234240.12062-1-vivek.kasireddy@intel.com
Otherwise BOs may wait for the fence indefinitely and never be destroyed.
v2: Signal the fence right after destroying queues to avoid unnecessary
delaye-delete in kfd_process_wq_release
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: xinhui pan <xinhui.pan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
and disable MC resum in VCN2.0 as well
those are not concerned by VF driver
Singed-off-by: darlington Opara <darlington.opara@amd.com>
Signed-off-by: Jinage Zhao <jiange.zhao@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
support IB test on dec/enc ring
disable ring test on dec/enc ring (MMSCH limitation)
v2: squash in unused variable warning fix
Singed-off-by: darlington Opara <darlington.opara@amd.com>
Signed-off-by: Jinage Zhao <jiange.zhao@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
something need to do for VCN2.0 enablement on SRIOV:
1)use one dec ring and one enc ring
2)allocate MM table for MMSCH usage
3)implement SRIOV version vcn_start which orgnize vcn programing
with patcket format and implement start mmsch for to run those
packet
4)doorbell is changed for SRIOV
Singed-off-by: darlington Opara <darlington.opara@amd.com>
Signed-off-by: Jinage Zhao <jiange.zhao@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MMSCH doesn't support jpeg ring on SRIOV
Signed-off-by: Jinage Zhao <jiange.zhao@amd.com>
Singed-off-by: darlington Opara <darlington.opara@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Because too many things are involved in this workaround, we need more
comments to avoid pitfalls.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add "CP" to AMDGPU_GEM_CREATE_MQD_GFX9 to indicate it is only for CP MQD
buffer.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
During GU reset PSP's sysfs was being wrongly reinitilized
during call to amdgpu_device_ip_late_init which was failing
with duplicate error.
Fix:
Move psp_sysfs_init to psp_sw_init to avoid this. Add guards
in sysfs file's read and write hook agains premature call
if PSP is not finished initialization.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SPM access the video memory according to SPM_VMID. It should be updated
with the job's vmid right before the job is scheduled. SPM_VMID is a
global resource
Signed-off-by: Jacob He <jacob.he@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
check UMC status and exit prior to making and erroneus register access
this resolved unexpected behaviour with UMC indexing mode broadcasting writes
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On arcturus, DF-Cstate needs to be toggled off/on
before and after accessing UMC error counter and
error address registers, otherwise, clearing such
registers may fail.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: John Clements <John.Clements@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mitigates race condition on BACO reset between GPU bootcode and driver reload
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add arcturus xgmi/wafl pcs err status group to support
PCS error detection and report on arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now driver will report XGMI/WAFL PCS error through
sysfs xgmi_wafl_err_count node on Vega20
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since from vega20, hardware supports run-time detect
and report XGMI/WAFL PCS ras error. Add helper functions
to walkthrough every type of ras error and report it if
any.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only user left is the shadow attach for legacy drivers.
v2: Shift the #ifdef CONFIG_DRM_LEGACY to now also include
drm_get_pci_dev() (Thomas)
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225165835.2394442-1-daniel.vetter@ffwll.ch
Depending on RNG we might try to fill an 8G region for every possible
order, using the smallest possible chunk size of 4K, which seems to be
very slow. Try to remedy the situation by adding an overall timeout for
the test, while also selecting each order level in a random fashion.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1310
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305204711.217783-2-matthew.auld@intel.com
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
drm_fb_helper_{add,remove}_one_connector() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-5-pankaj.laxminarayan.bharadiya@intel.com
drm_fb_helper_{add,remove}_one_connector() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-4-pankaj.laxminarayan.bharadiya@intel.com
drm_fb_helper_{add,remove}_one_connector() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-3-pankaj.laxminarayan.bharadiya@intel.com
The max connector argument for drm_fb_helper_init() isn't used anymore
hence remove it.
All the drm_fb_helper_init() calls are modified with below sementic
patch.
@@
expression E1, E2, E3;
@@
- drm_fb_helper_init(E1,E2, E3)
+ drm_fb_helper_init(E1,E2)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-2-pankaj.laxminarayan.bharadiya@intel.com
Check the edge case where batch_start_offset sits exactly on the batch
size.
v2: add new range_overflows variant to capture the special case where
the size is permitted to be zero, like with batch_len.
v3: other way around. the common case is the exclusive one which should
just be >=, with that we then just need to convert the three odd ball
cases that don't apply to use the new inclusive _end version.
Testcase: igt/gem_exec_params/invalid-batch-start-offset
Fixes: 0b5372727b ("drm/i915/cmdparser: Use cached vmappings")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306094735.258285-1-matthew.auld@intel.com
Unbreak the DRM menu. This Kconfig symbol does not depend on DRM,
so the menu is broken at that point.
Move the symbol to a location in the Kconfig file so that it does
not break the dependency continuity.
Fixes: 6349120ddc ("drm: Move EXPORT_SYMBOL_FOR_TESTS_ONLY under a separate Kconfig")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/04221997-79ba-f8a2-4f2d-3c3d9f5219bc@infradead.org
We try hard to select a suitable hole in the drm_mm first time. But if
that is unsuccessful, we then have to look at neighbouring nodes, and
this requires traversing the rbtree. Walking the rbtree can be slow
(much slower than a linear list for deep trees), and if the drm_mm has
been purposefully fragmented our search can be trapped for a long, long
time. For non-preemptible kernels, we need to break up long CPU bound
sections by manually checking for cond_resched(); similarly we should
also bail out if we have been told to terminate. (In an ideal world, we
would break for any signal, but we need to trade off having to perform
the search again after ERESTARTSYS, which again may form a trap of
making no forward progress.)
Reported-by: Zbigniew Kempczyński <zbigniew.kempczynski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zbigniew Kempczyński <zbigniew.kempczynski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207151720.2812125-1-chris@chris-wilson.co.uk
We only need to serialise the multiple pinning during the eb_reserve
phase. Ideally this would be using the vm->mutex as an outer lock, or
using a composite global mutex (ww_mutex), but at the moment we are
using struct_mutex for the group.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1381
Fixes: 003d8b9143 ("drm/i915/gem: Only call eb_lookup_vma once during execbuf ioctl")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306071614.2846708-3-chris@chris-wilson.co.uk
We only call i915_schedule() when we know we have changed the priority
on a request and so require to propagate any change in priority to its
signalers (for PI). By unconditionally checking all of our signalers, we
avoid skipping changes made prior to construction of the request (as the
request may be waited upon before submission when used in parallel).
References: https://gitlab.freedesktop.org/drm/intel/issues/1318
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306071614.2846708-2-chris@chris-wilson.co.uk
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305105707.GA19261@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305105306.GA18788@embeddedor
The alignment is u64, and yet is_power_of_2() assumes unsigned long,
which might give different results between 32b and 64b kernel.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
The release method will undo what we did at creation, and so we
shouldn't care if we have pages or not. Fixes a small leak in the
mock_phys selftest.
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305204258.216302-1-matthew.auld@intel.com
On gen7 and gen7.5 devices, there could be leftover data residuals in
EU/L3 from the retiring context. This patch introduces workaround to clear
that residual contexts, by submitting a batch buffer with dedicated HW
context to the GPU with ring allocation for each context switching.
This security mitigation changes does not triggers any performance
regression. Performance is on par with current drm-tips.
v2: Add igt generated header file for CB kernel assembled with Mesa tool
and addressed use of Kernel macro for ptr_align comment.
v3: Resolve Sparse warnings with newly generated, and imported CB
kernel.
v4: Include new igt generated CB kernel for gen7 and gen7.5. Also
add code formatting and compiler warnings changes (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Acked-by: Chris Wilson <chris@chris-wilso.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306000957.2836150-2-chris@chris-wilson.co.uk
This patch adds framework to submit an arbitrary batchbuffer on each
context switch to clear residual state for render engine on Gen7/7.5
devices.
The idea of always emitting the context and vm setup around each request
is primary to make reset recovery easy, and not require rewriting the
ringbuffer. As each request would set up its own context, leaving it to
the HW to notice and elide no-op context switches, we could restart the
ring at any point, and reorder the requests freely.
However, to avoid emitting clear_residuals() between consecutive requests
in the ringbuffer of the same context, we do want to track the current
context in the ring. In doing so, we need to be careful to only record a
context switch when we are sure the next request will be emitted.
This security mitigation change does not trigger any performance
regression. Performance is on par with current mainline/drm-tip.
v2: Update vm_alias params to point to correct address space "vm" due to
changes made in the patch "f21613797bae98773"
v3-v4: none
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306000957.2836150-1-chris@chris-wilson.co.uk
Per-CRTC VBLANK information used to be addressed by device and pipe
index. A call drm_crtc_vblank_helper_get_vblank_timestamp_internal()
receives a pointer to the CRTC instead. Fix the documentation.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: f1e2b6371c ("drm: Add get_scanout_position() to struct drm_crtc_helper_funcs")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200303073135.10605-1-tzimmermann@suse.de
Brings the documentation of drm_simple_encoder_init() in sync with the
function's signature. Also add a paragraph clarifying the management of
the encoder's memory.
v2:
* document memory management
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 63170ac6f2 ("drm/simple-kms: Add drm_simple_encoder_{init,create}()")
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200304145312.26458-1-tzimmermann@suse.de
Without this, we get a couple of warnings when CONFIG_PM
is disabled:
drivers/gpu/drm/arm/display/komeda/komeda_drv.c:156:12: error: 'komeda_rt_pm_resume' defined but not used [-Werror=unused-function]
static int komeda_rt_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/arm/display/komeda/komeda_drv.c:149:12: error: 'komeda_rt_pm_suspend' defined but not used [-Werror=unused-function]
static int komeda_rt_pm_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
Fixes: efb4650885 ("drm/komeda: Add runtime_pm support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: james qian wang (Arm Technology China) <james.qian.wang@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107215327.1579195-1-arnd@arndb.de
Teach gvt to use intel_gt directly as it currently assumes direct HW
access.
[Zhenyu: rebase, fix compiling]
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-3-zhenyuw@linux.intel.com
Stop trying to escape out of the gvt layer to find the engine that we
initially setup for use with gvt. Record the engines during initialisation
and use them henceforth.
add/remove: 1/4 grow/shrink: 22/28 up/down: 341/-1410 (-1069)
[Zhenyu: rebase, fix nonpriv register check fault, fix gvt engine
thread run failure.]
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-2-zhenyuw@linux.intel.com
Remove extra chatty message for debugfs scan_nonprivbb which is used
to enable scan for non privileged batch on specific engine. Just write
target i915 engine mask instead.
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-1-zhenyuw@linux.intel.com
Commit c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
added the support on CFL. The vgpu emulation hotplug support on CFL was
supposed to be included in that patch. Without the vgpu emulation
hotplug support, the dma-buf based display gives us a blur face.
So fix this issue by adding the vgpu emulation hotplug support on CFL.
Fixes: c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200227010041.32248-1-tina.zhang@intel.com
The emulated vbt doesn't tell its size correctly. According to the
intel_vbt_defs.h, vbt_header.vbt_size should the size of VBT (VBT Header,
BDB Header and data blocks), and bdb_header.bdb_size should be the size
of BDB (BDB Header and data blocks).
This patch fixes the issue and lets vbt provided by GVT-g pass the guest
i915's sanity test.
v2: refine the commit message. (Zhenyu)
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200305131600.29640-1-tina.zhang@intel.com
Panel driver for the KD35T133 display from Elida, used for example
in the rk3326-based Odroid Go Advance handheld.
changes in v3:
- add missing return value assignment (Francesco)
- re-sort header includes (Sam)
changes in v2:
- rename dsi_generic_write_seq macro to dsi_dcs_write_seq to honor
the underlying mipi_dsi_dcs_write (Robin)
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200229151506.750242-3-heiko@sntech.de
- Break up long lists of object reclaim with cond_resched()
- PSR probe fix
- TGL workarounds
- Selftest return value fix
- Drop timeline mutex while waiting for retirement
- Wait for OA configuration completion before writes to OA buffer
-----BEGIN PGP SIGNATURE-----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=kXvj
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2020-03-05' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.6-rc5:
- Break up long lists of object reclaim with cond_resched()
- PSR probe fix
- TGL workarounds
- Selftest return value fix
- Drop timeline mutex while waiting for retirement
- Wait for OA configuration completion before writes to OA buffer
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87eeu7nl6z.fsf@intel.com
Requests within a timeline are ordered by that timeline, so awaiting for
the start of a request within the timeline is a no-op. This used to work
by falling out of the mutex_trylock() as the signaler and waiter had the
same timeline and not returning an error.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305134822.2750496-1-chris@chris-wilson.co.uk
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When hit COMBINATIONAL_BYPASS the mclk will be bypass and can export
fclk frequency to user usage.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This fix will handle some MP1 FW issue like as mclk dpm table in renoir has a reverse
dpm clock layout and a zero frequency dpm level as following case.
cat pp_dpm_mclk
0: 1200Mhz
1: 1200Mhz
2: 800Mhz
3: 0Mhz
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
CP firmware decide to skip setting the state for 3D pipe 1 for Navi1x as there
is no use case.
[how]
Disable 3D pipe 1 on Navi1x.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix the inverted test to emit the wait on the end of the previous
request if we /haven't/ already.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305104210.2619967-1-chris@chris-wilson.co.uk
Converting error to debug print if sink fails to configure scrambling or
TMDS bit clock ratio. In this case, we are timing out while disabling
the scrambling and setting the SCDC ratio, as there is no response
to the I2C SCDC write from the sink device. Error isn't due to something
wrong done from driver side.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302213807.6488-1-swati2.sharma@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
We are mistakenly skipping transition watermarks on glk. Fix
up the condition for glk, and toss in the w/a name from
the database.
v2: Reorder the ipc enabled vs. platform check to be more sensible
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-3-ville.syrjala@linux.intel.com
Currently we're comparing the watermarks between the old and new states
before we've fully computed the new watermarks. In particular
skl_build_pipe_wm() will not account for the amount of ddb space we'll
have. That information is only available during skl_compute_ddb()
which will proceed to zero out any watermark level exceeding the
ddb allocation. If we're short on ddb space this will end up
adding the plane to the state due erronously determining that the
watermarks have changed. Fix the problem by deferring
skl_wm_add_affected_planes() until we have the final watermarks
computed.
Noticed this when trying enable transition watermarks on glk.
We now computed the trans_wm as 28, but we only had 14 blocks
of ddb, and thus skl_compute_ddb() ended up disabling the cursor
trans_wm every time. Thus we ended up adding the cursor to every
commit that didn't actually affect the cursor at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The hardware never sees the uv_wm values (apart from
uv_wm.min_ddb_alloc affecting the ddb allocation). Thus there
is no point in comparing uv_wm to determine if we need to
reprogram the watermark registers. So let's check only the
rgb/y watermark in skl_plane_wm_equals(). But let's leave
a comment behind so that the next person reading this doesn't
get as confused as I did when I added this check.
If the ddb allocation ends up changing due to uv_wm
skl_ddb_add_affected_planes() takes care of adding the plane
to the state.
TODO: we should perhaps just eliminate uv_wm from the state
and simply track the min_ddb_alloc for uv instead.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Enable FtrPerCtxtPreemptionGranularityControl bit and select thread-
group as the default preemption level.
v2:
* Remove register whitelisting (Rafael, Tony).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: piotr.zdunowski@intel.com
Cc: michal.mrozek@intel.com
Cc: Tony Ye <tony.ye@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Acked-by: Rafael Antognolli <rafael.antognolli@intel.com>
Acked-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tony Ye <tony.ye@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304153144.10675-1-tvrtko.ursulin@linux.intel.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
The wait_for macro's for Broadcom V3D driver used msleep, which is
inappropriate due to its inaccuracy at low values (minimum wait time
is about 30ms on the Raspberry Pi). This sleep was triggering in
v3d_clean_caches(), causing us to only be able to dispatch ~33 compute
jobs per second.
This patch replaces the macro with the one from the Intel i915 version
which uses usleep_range to provide more accurate waits.
v2: Split from the vc4 patch so that we can confidently apply to
stable (by anholt)
Signed-off-by: James Hughes <james.hughes@raspberrypi.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200217153145.13780-1-james.hughes@raspberrypi.com
Link: https://github.com/raspberrypi/linux/issues/3460
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
The wait_for macro's for Broadcom VC4 driver used msleep, which is
inappropriate due to its inaccuracy at low values (minimum wait time
is about 30ms on the Raspberry Pi). This sleep was triggering in
v3d_clean_caches(), causing us to only be able to dispatch ~33 compute
jobs per second.
This patch replaces the macro with the one from the Intel i915 version
which uses usleep_range to provide more accurate waits.
v2: Split from the v3d patch in case this tickles modesetting bugs (by
anholt)
Signed-off-by: James Hughes <james.hughes@raspberrypi.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200217153145.13780-1-james.hughes@raspberrypi.com
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid compile errors on other platforms.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starts USBC PD FW download and reads back the latest FW version.
v2:
Move sysfs file creation to late init
Add locking around PSP calls to avoid concurrent access to PSP's C2P registers
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Used to load power Delivery FW to PSP.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ROMC_INDEX/DATA offset was changed to e4/e5 since
from smuio_v11 (vega20/arcturus).
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Tested-by: Candice Li <Candice.Li@amd.com>
Reviewed-by: Candice Li <Candice.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HDP ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MMHUB ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SDMA ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Navi12 VK CTS subtest timestamp.calibrated.dev_domain_test failed
because mmRLC_CAPTURE_GPU_CLOCK_COUNT register cannot be
written in VF due to security policy.
Solution: use a VF-accessible timestamp register pair
mmGOLDEN_TSC_COUNT_LOWER/UPPER for SRIOV case.
v2: according to Deucher Alexander's advice, switch to
mmGOLDEN_TSC_COUNT_LOWER/UPPER for both bare metal and SRIOV.
Signed-off-by: jianzh <Jiange.Zhao@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When hit COMBINATIONAL_BYPASS the mclk will be bypass and can export
fclk frequency to user usage.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fix will handle some MP1 FW issue like as mclk dpm table in renoir has a reverse
dpm clock layout and a zero frequency dpm level as following case.
cat pp_dpm_mclk
0: 1200Mhz
1: 1200Mhz
2: 800Mhz
3: 0Mhz
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With new L1 policy, some regs are blocked at guest and they are
programed at host side. So skip programing the regs under sriov.
the regs are:
GCMC_VM_FB_LOCATION_TOP
GCMC_VM_FB_LOCATION_BASE
MMMC_VM_FB_LOCATION_TOP
MMMC_VM_FB_LOCATION_BASE
GCMC_VM_SYSTEM_APERTURE_HIGH_ADDR
GCMC_VM_SYSTEM_APERTURE_LOW_ADDR
MMMC_VM_SYSTEM_APERTURE_HIGH_ADDR
MMMC_VM_SYSTEM_APERTURE_LOW_ADDR
HDP_NONSURFACE_BASE
HDP_NONSURFACE_BASE_HI
GCMC_VM_AGP_TOP
GCMC_VM_AGP_BOT
GCMC_VM_AGP_BASE
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some lttpr devices do not work properly when lttpr mode is configured
after link settings.
[How]
Move lttpr configuration before lane settings.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logger mask was updated to uint64_t, however default mask definition was
not updated for unsigned long long
[How]
Update DC_DEFAULT_LOG_MASK to support uint64_t type
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When transitioning from SST to MST, the HDCP repeater in some MST
displays will enter a bad state. The HDCP repeater is recovered after
failing and performing authentication again.
[How]
Add monitor patch to trigger HDCP authentication failure after
encryption is enabled and re-authenticate.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Typo in amdgpu_dm error message:
"Failed to found connector for link!"
[How]
1. Replace with:
"Failed to find connector for link!"
2. Fix indentation checkpatch warnings.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reset connection is called before remove display in mod_hdcp. When
remove display is called, the display structure has been zeroed from
reset connection. Since no displays can be found, remove display does
not properly reset the hardware. This causes validation errors when
another display is plugged into a different port afterwards.
[How]
Moved displays structure out of connections structure. Displays
structure is now directly within mod_hdcp. Displays is no longer zeroed
when reset connection is called.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ported from Vega10. SDMA stress tests sometimes see IRQ lost.
Signed-off-by: Samir Dhume <samir.dhume@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
scratch_reg0 is used by RLCG for register access usage
in SRIOV case.
both CP firmware and driver can invoke RLCG to do
certain register access (through scratch_reg0/1/2/3)
but rlcg now dosen't have race concern so if two
clients are in parallel doing the RLCG reg access
then we are colliding,
GFX IB test is a runtime work, so it is forbidden
to use scrach_reg0/1/2/3 during IB test period
note:
Although we can only have this change for SRIOV, but
looks it doesn't worth the effort to differentiate
bare-metal with SRIOV on the GFX ib test
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1)for gfx IB test we shouldn't insert DE meta data
2)we should make sure IB test finished before we
send event 3 to hypervisor otherwise the IDLE from
event 3 will preempt IB test, which is not designed
as a compatible structure for MCBP
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
CP firmware decide to skip setting the state for 3D pipe 1 for Navi1x as there
is no use case.
[how]
Disable 3D pipe 1 on Navi1x.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add debugfs interface amdgpu_force_sclk
to set arbitrary sclk for navi14
v2: Add lock
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a statement that is indented with spaces instead of a tab.
Replace spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change programs CP_ME_CNTL and RLC_CSIB_* through RLC
Signed-off-by: Rohit Khaire <Rohit.Khaire@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Thundersoft TST178 tablet uses a DSI panel with an external PWM
controller (as all DSI panels do). But unlike other DSI panels a duty-cycle
of 100% turns the backlight off and 0% sets it to maximum brightness.
I've checked the VBT and there is a BDB_LVDS_BACKLIGHT section, but
it does not set the active_low_pwm flag. This tablet re-uses the main
PCI vendor and product ids for the subsystem ids, so I see no other option
then to add a DMI based quirk to fix this.
Note that the PWM backlight code in intel_panel.c currently does not honor
the vbt.active_low_pwm flag, but that does not matter in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-2-hdegoede@redhat.com
Use intel_panel_compute_brightness() from pwm_setup_backlight() so that
we correctly take i915_modparams.invert_brightness and/or
QUIRK_INVERT_BRIGHTNESS into account when setting + getting the initial
brightness value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-1-hdegoede@redhat.com
Trying to use i915_request_skip() prior to i915_request_add() causes us
to try and fill the ring upto request->postfix, which has not yet been
set, and so may cause us to memset() past the end of the ring.
Instead of skipping the request immediately, just flag the error on the
request (only accepting the first fatal error we see) and then clear the
request upon submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304121849.2448028-1-chris@chris-wilson.co.uk
intel_ddi_clock_get() tests the DPLL ID against DPLL_ID_ICL_TBTPLL (2)
to determine whether to try to descend into a TBT-specific handler.
However this test will also be true when DPLL4 on EHL is used since that
shares the same DPLL ID (2).
Add an extra check to ensure the PHY is actually a Type-C PHY before
descending into the TBT handling. This should ensure EHL still takes
the correct code path and somewhat future-proof the code as well.
v2: Drop the gen+ check since only gen11+ platforms can have Type-C
outputs. (Imre)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1369
Fixes: 45e4728b87 ("drm/i915: Move DPLL frequency calculation to intel_dpll_mgr.c")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303195043.959913-1-matthew.d.roper@intel.com
This reverts commit ff57c65138.
With the commit ff57c65138 ("drm: kirin: Fix for hikey620
display offset problem") we added support for handling LDI
overflows by resetting the hardware.
However, its been observed that when we do hit the LDI overflow
condition, the irq seems to be screaming, and we do nothing but
stream:
[drm:ade_irq_handler [kirin_drm]] *ERROR* LDI underflow!
over and over to the screen
I've tried a few appraoches to avoid this, but none has yet
been successful and the cure here is worse then the original
disease, so revert this for now.
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Fixes: ff57c65138 ("drm: kirin: Fix for hikey620 display offset problem")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303163228.52741-1-john.stultz@linaro.org
As we have pinned the timeline (using tl->active_count), we can safely
drop the tl->mutex as we wait for what we believe to be the final
request on that timeline. This is useful for ensuring that we do not
block the engine heartbeat by hogging the kernel_context's timeline on a
dead GPU.
References: https://gitlab.freedesktop.org/drm/intel/issues/1364
Fixes: 058179e72e ("drm/i915/gt: Replace hangcheck by heartbeats")
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303140009.1494819-1-chris@chris-wilson.co.uk
(cherry picked from commit 82126e596d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We still need to wait for the initial OA configuration to happen
before we enable OA report writes to the OA buffer.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 15d0ace1f8 ("drm/i915/perf: execute OA configuration from command stream")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1356
Testcase: igt/perf/stream-open-close
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302085812.4172450-7-chris@chris-wilson.co.uk
(cherry picked from commit 4b4e973d5e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drivers/gpu/drm/i915/gvt/gvt.c:264:6: error: no previous prototype for ‘intel_gvt_clean_device’ [-Werror=missing-prototypes]
drivers/gpu/drm/i915/gvt/gvt.c:301:5: error: no previous prototype for ‘intel_gvt_init_device’ [-Werror=missing-prototypes]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304002331.2126072-1-chris@chris-wilson.co.uk
According to Dell, trying to match their panels via OUI is not reliable
enough and we've been told that we should check against the EDID
instead. As well, Dell seems to have some panels that are actually
intended to switch between using PWM for backlight controls and DPCD for
backlight controls depending on whether or not the panel is in HDR or
SDR mode. Yikes.
Regardless, we need to add quirks for these so that DPCD backlight
controls get enabled by default, since without additional driver support
that's the only form of brightness control that will work. Hopefully in
the future we can remove these quirks once we have a better way of
probing for this.
Changes since v1:
* Add one more EDID per Dell's request
* Remove model number (which is possibly wrong) and replace with Dell
CML 2020 systems
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-4-lyude@redhat.com
Reviewed-by: Adam Jackson <ajax@redhat.com>
The X1 Extreme is one of the systems that lies about which backlight
interface that it uses in its VBIOS as PWM backlight controls don't work
at all on this machine. It's possible that this panel could be one of
the infamous ones that can switch between PWM mode and DPCD backlight
control mode, but we haven't gotten any more details on this from Lenovo
just yet. For the time being though, making sure the backlight 'just
works' is a bit more important.
So, add a quirk to force DPCD backlight controls on for these systems
based on EDID (since this panel doesn't appear to fill in the device ID).
Hopefully in the future we'll figure out a better way of probing this.
Changes since v2:
* The bugzilla URL is deprecated, bug reporting happens on gitlab now.
Update the messages we print to reflect this
* Also, take the opportunity to move FDO_BUG_URL out of i915_utils.c and
into i915_utils.h so that other places which print things that aren't
traditional errors but are worth filing bugs about, can actually use
it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303215320.93491-1-lyude@redhat.com
The whole point of using OUIs is so that we can recognize certain
devices and potentially apply quirks for them. Normally this should work
quite well, but there appears to be quite a number of laptop panels out
there that will fill the OUI but not the device ID. As such, for devices
like this I can't imagine it's a very good idea to try relying on OUIs
for applying quirks. As well, some laptop vendors have confirmed to us
that their panels have this exact issue.
So, let's introduce the ability to apply DP quirks based on EDID
identification. We reuse the same quirk bits for OUI-based quirks, so
that callers can simply check all possible quirks using
drm_dp_has_quirk().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-2-lyude@redhat.com
DP shim's config_stream_type considered to be succeeded when
return value of intel_dp_hdcp2_write_msg() equals to size of
message to be written, it makes config_stream_type to return
a zero success value in order to succeed the HDCP auth.
v2:
- config_stream_type() returns 0 on success. [Ram]
CC: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303073838.25871-1-anshuman.gupta@intel.com
HDCP Repeater initializes seq_num_V to 0 at the beginning of
hdcp Session i.e. after AKE_init received, refer
HDCP 2.2 Spec HDMI PAGE 19, DP PAGE 20.
HDCP 2.2 Comp specs 1B-06 test verifies that whether DUT
considers failure of authentication if the repeater provides a
non-zero value in seq_num_V in the first,
RepeaterAuth_Send_ReceiverID_List message.
Make sure that HDCP repeater initializes seq_num_V to zero at
beginning of session i.e. after AKE_Init, fail the Auth if
there is non zero seq_num_V.
v2:
- Used existing hdcp2_encrypted flag instead of
declaring new flag. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200220123217.23635-2-anshuman.gupta@intel.com
As we are not using the sysfs infrastructure anymore, link to it is
removed. And global srm data and mutex to protect it are removed,
with required handling at revocation check function.
v2:
srm_data is dropped and few more comments are addressed.
v3:
ptr passing around is fixed with functional testing.
v4:
fix htmldoc [lkp]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Suggested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212102942.26568-2-ramalingam.c@intel.com
This change adds the below gpu memory tracepoint:
gpu_mem/gpu_mem_total: track global or proc gpu memory total usages
Per process tracking of total gpu memory usage in the gem layer is not
appropriate and hard to implement with trivial overhead. So for the gfx
device driver layer to track total gpu memory usage both globally and
per process in an easy and uniform way is to integrate the tracepoint in
this patch to the underlying varied implementations of gpu memory
tracking system from vendors.
Putting this tracepoint in the common trace events can not only help
wean the gfx drivers off of debugfs but also greatly help the downstream
Android gpu vendors because debugfs is to be deprecated in the upcoming
Android release. Then the gpu memory tracking of both Android kernel and
the upstream linux kernel can stay closely, which can benefit the whole
kernel eco-system in the long term.
Link: http://lkml.kernel.org/r/20200302235044.59163-1-zzyiwei@google.com
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Yiwei Zhang <zzyiwei@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As we no longer stash anything inside i915_vma under the exclusive
protection of struct_mutex, we do not need to revoke the i915_vma
stashes before dropping struct_mutex to handle pagefaults. Knowing that
we must drop the struct_mutex while keeping the eb->vma around, means
that we are required to hold onto to the object reference until we have
marked the vma as active.
Fixes: 155ab8836c ("drm/i915: Move object close under its own lock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-3-chris@chris-wilson.co.uk
For our convenience, and to avoid frequent allocations, we placed some
lists we use for execbuf inside the common i915_vma struct. As we look
to parallelise execbuf, such fields guarded by the struct_mutex BKL must
be pulled under local control. Instead of using the i915_vma as our
primary means of tracking the user's list of objects and their virtual
mappings, we use a local eb_vma with the same lists as before (just now
local not global).
This should allow us to only perform the lookup of vma used for
execution once during the execbuf ioctl, as currently we need to remove
our secrets from inside i915_vma everytime we drop the struct_mutex as
another execbuf may use the shared locations.
Once potential user visible consequence is that we can remove the
requirement that the execobj[] be unique, and only require that they do
not conflict (i.e. you cannot softpin the same object into two locations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-2-chris@chris-wilson.co.uk
With the goal of removing the serialisation from around execbuf, we will
no longer have the privilege of there being a single execbuf in flight
at any time and so will only be able to inspect the user's flags within
the carefully controlled execbuf context. i915_gem_evict_for_node() is
the only user outside of execbuf that currently peeks at the flag to
convert an overlapping softpinned request from ENOSPC to EINVAL. Retract
this nicety and only report ENOSPC if the location is in current use,
either due to this execbuf or another.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-1-chris@chris-wilson.co.uk
DE3 VI layers support alpha blending, but DE2 VI layers do not.
Additionally, DE3 VI layers support 10-bit RGB and YUV formats.
Make a separate list for DE3.
Fixes: c50519e6db ("drm/sun4i: Add basic support for DE3")
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224173901.174016-3-jernej.skrabec@siol.net
Following the changes in the previous patch
"drm/i915/gen11: Moving WAs to rcs_engine_wa_init()" also moving TGL
Wa_1408615072 to rcs_engine_wa_init() this way after a engine
reset it will be reapplied also restricting it to A0 as it is fixed in
B0 stepping.
BSpec: 52890
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302231421.224322-2-jose.souza@intel.com
This are register of render engine, so after a render reset those
would return to the default value and init_clock_gating() is not
called for single engine reset.
So here moving it rcs_engine_wa_init() that will guarantee that this
WAs will not be lost.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302231421.224322-1-jose.souza@intel.com
Static code analysis tool identified struct lrc_timestamp data as being
uninitialized and then data.ce[] is being checked for NULL/negative
value in the error path. Initializing data variable fixes the issue.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303142347.15696-1-aditya.swarup@intel.com
As we have pinned the timeline (using tl->active_count), we can safely
drop the tl->mutex as we wait for what we believe to be the final
request on that timeline. This is useful for ensuring that we do not
block the engine heartbeat by hogging the kernel_context's timeline on a
dead GPU.
References: https://gitlab.freedesktop.org/drm/intel/issues/1364
Fixes: 058179e72e ("drm/i915/gt: Replace hangcheck by heartbeats")
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303140009.1494819-1-chris@chris-wilson.co.uk
The is-closed flag may be added after we have acquired the vma under the
ctx->mutex, but will not take effect until after we release the
vm->mutex. i.e. the flag may be set on the vma as attempt to bind it and
that will cause the vma to be unbound later after we unpin it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303093157.1153887-1-chris@chris-wilson.co.uk
As setup takes a long time, the user may close the context during the
construction of the execbuf. In order to make sure we correctly track
all outstanding work with non-persistent contexts, we need to serialise
the submission with the context closure and mop up any leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303080546.1140508-3-chris@chris-wilson.co.uk
It irks me to use crtc_state_is_legacy_gamma() inside the guts
of the CHV color management code. Let's get rid of it and instead
just consult cgm_mode to figure out if we want to enable the pipe
gamma or the CGM gamma.
Also CHV display engine is based on i965/g4x so we should fall back
to the i965 path when the CGM gamma is not used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107151725.10507-3-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Add intel_vgpu_register() abstraction, rename i915_detect_vgpu() to
intel_vgpu_detect() to match other function naming, un-inline
intel_vgpu_active(), intel_vgpu_has_full_ppgtt() and
intel_vgpu_has_huge_gtt() to reduce header interdependencies.
The i915_vgpu.[ch] filename and intel_vgpu_ prefix discrepancy remains.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227144408.24345-1-jani.nikula@intel.com
has_transcoder() was unused because function which was using it,
intel_display_capture_error_state() defined under
CONFIG_DRM_I915_CAPTURE_ERROR.
Moving has_transcoder() to under CONFIG_DRM_I915_CAPTURE_ERROR.
No functional change.
Fixes: d54c1a513c ("drm/i915: Fix broken transcoder err state")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227175147.11362-1-anshuman.gupta@intel.com
Converts remaining instances of the printk based logging macros in
i915/display/intel_hdcp.c with the struct drm_device based macros
manually.
This is continuation of commit 65833c4638 ("drm/i915/hdcp: conversion
to struct drm_device based logging macros.")
v2:
i915_dev_priv is used instead of drm_device for reusability [JaniN]
v3:
Made it independent from the series.
once instance of dev_priv naming is changed to i915 [Jani N]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212123007.6659-1-ramalingam.c@intel.com
If the GPU isn't idle after signalling pm_runtime_mark_last_busy() plus
waiting for the autosuspend delay there's likely something wrong with
the way we check idleness so warn about that.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Without that runtime suspend is often blocked due to
etnaviv_gpu_rpm_suspend() returning -EBUSY since the FE seems to trigger
the MC in its idle loop.
Ignoring the MC bit makes the GPU suspend as expected. This was tested
on GC7000.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
We were missing out on some bits the vendor kernel driver knows about.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Update the state HI and common header from rnndb commit
commit 19280a95a (rnndb: Update idle bits)
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Use 'is' instead of 'it' so it becomes a valid sentence and
spell 'resetting' correctly.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Report the correct perfmon domains and signals depending
on the supported feature flags.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9e2c2e2730 ("drm/etnaviv: add infrastructure to query perf counter")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
From commit f25a49ab8a ("drm/i915/gvt: Use vgpu_lock to protect per
vgpu access") the vgpu idr destroy is moved later than vgpu resource
destroy, then it would fail to stop timer for schedule policy clean
which to check vgpu idr for any left vGPU. So this trys to destroy
vgpu idr earlier.
Cc: Colin Xu <colin.xu@intel.com>
Fixes: f25a49ab8a ("drm/i915/gvt: Use vgpu_lock to protect per vgpu access")
Acked-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200229055445.31481-1-zhenyuw@linux.intel.com
Update to the latest available TGL HuC, which includes changes required
by the media team.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tony Ye <tony.ye@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Tony Ye <tony.ye@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200229012042.27487-1-daniele.ceraolospurio@intel.com
We still need to wait for the initial OA configuration to happen
before we enable OA report writes to the OA buffer.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 15d0ace1f8 ("drm/i915/perf: execute OA configuration from command stream")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1356
Testcase: igt/perf/stream-open-close
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302085812.4172450-7-chris@chris-wilson.co.uk
Different issues with the same fix, so justing adding
Wa_1409142259, Wa_1409252684, Wa_1409217633, Wa_1409207793,
Wa_1409178076 and 1408979724 to the comment so other devs can check if
this Was were implemetend with a simple grep.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-8-jose.souza@intel.com
According to BSpec. Wa_1606931601 applies for all TGL steppings.
This patch moves the WA implementation out of A0 only block of
rcs_engine_wa_init().
The WA is has also been referred to by an alternate name
Wa_1607090982.
Bspec: 46045, 52890
Fixes: 3873fd1a43 ("drm/i915: Use engine wa list for Wa_1607090982")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-4-jose.souza@intel.com
Disable Push Constant buffer addition for TGL.
v2: typos, add additional Wa reference
v3: use REG_BIT macro, move to rcs_engine_wa_init, clean up commit
message.
Bspec: 52890
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-3-jose.souza@intel.com
This will whitelist the HIZ_CHICKEN register so mesa can disable the
optimizations and avoid hang when using D16_UNORM.
v2: moved to the right place and used the right function() (Chris)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-2-jose.souza@intel.com
This workaround the CS not done issue on PIPE_CONTROL.
v2:
- replaced BIT() by REG_BIT() in all GEN7_ROW_CHICKEN2() bits
- shortened the name of the new bit
BSpec: 52890
BSpec: 46218
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-1-jose.souza@intel.com
All platforms using the shared DPLL framework use 3 reference clocks for
their DPLLs: SSC, non-SSC and DSI. For a more unified way across
platforms store the frequency of these ref clocks as part of the DPLL
global state. This also allows us to keep the HW access reading out the
ref clock value separate from the DPLL frequency calculation that
depends on the ref clock.
For now add only the SSC and non-SSC ref clocks, as the pre-ICL DSI code
has its own logic for calculating DPLL parameters instead of the shared
DPLL framework.
v2:
- Apply the ICL combo PHY PLL ref_clock/2 adjustment during the
frequency->PLL param conversion direction as well. (CI shards)
- s/kHZ/kHz/ (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228153328.17842-1-imre.deak@intel.com
The types of PLLs used for HDMI/DP on HSW are WRPLL/LCPLL accordingly,
so use these names to align better with the rest of WRPLL/LCPLL function
names elsewhere.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-9-imre.deak@intel.com
For clarity keep the SKL DPLL ref clock in a variable instead of
open-coding it. Store the value in kHZ units as done on other platforms.
This allows us in a later patch to keep track of the DPLL ref clock in a
more unified way across all platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-8-imre.deak@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
For clarity add a new DPLL specific struct to the i915 device struct and
move all DPLL fields into it. Accordingly remove the dpll_ prefixes, as
the new struct already provides the required namespacing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-4-imre.deak@intel.com
