This patch adds
-Loading the firmware
-The functions and definitions for communication with the firmware
v2: Fix formatting
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There can be some unsynchronized frames when entering/exiting
LFC. This may cause tearing or stuttering at such transitions.
[How]
Add a enter/exit margin to algorithm to smoothly transition into
and out of LFC without desynchronizing frames.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Detile buffer size affects dcc caps and therefore needs to be
corrected for each ip.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
tg_inst may be used uninitialized, so initialize it to 0.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When more than 2 displays are connected to the graphics card,
only the minimum memory clock is needed. However, when more
displays are connected, the minimum memory clock is not
sufficient enough to support the overwhelming bandwidth.
System will hang under this circumstance.
Also, the old code didn't address HBM cards, which has 2
pseudo channels. We need to add the HBM part here.
[How]
When graphics card connects to 2 or more displays,
switch to high memory clock. Also, choose memory
multiplier based on whether its regular DRAM or HBM.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
seamless boot didn't work for non edp's before
[how]
removed edp-specific code, made dp read uefi-set link settings. Also fixed
a hubbub code line to be consistent with usage of function.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously 8k30 worked with dsc and odm combine due to a workaround that ran
the formula a second time with dsc support enable should dsc validation fail.
This worked when clocks were low enough for formula to enable odm to lower
voltage, however now broke due to increased clocks.
This change updates the ODM combine policy within the formula to properly
reflect our current policy within DC, only enabling ODM when we have to, as
well as adding a check for viewport width when dsc is enabled.
As a side effect the redundant call to dml when odm is required is now
unnecessary.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Presently, there is no way for clocks to be lowered, only raised.
[HOW]
Compare clock status against previous known clock status, and optimize
if different.
This requires re-ordering the layout of the dc_clocks structure, as the
current ordering allows identical clock states to appear different.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some ODM-related register settings are inconsistently updated by VBIOS, causing
the state in DC to be invalid, which would then end up crashing in certain
use-cases (such as disable/enable device).
[how]
Check the enabled status of the second pipe when determining the number of
OPTC sources. If the second pipe is disabled, set the number of sources to 1
regardless of other settings (that may not be updated correctly).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A lot of the time, the backlight characteristic curve maps min backlight
to a non-zero value.
But there are cases where we want the curve to intersect at 0.
In this scenario even if OS never asks to set 0% backlight, the ABM
reduction can result in backlight being lowered close to 0.
This particularly can cause problems in some LED drivers, and in
general just looks like backlight is completely off.
[How]
Add default cap to disallow backlight from dropping below 1%
even after ABM reduction is applied.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This change was made because DTO programming was double-buffered, which
is itself an issue. After deactivating the DTO double buffer, this
change becomes unnecessary.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When changing DPP global ref clock, DTO adjustments must take effect
immediately, or else underflow may occur.
It appears the original decision to double-buffer DTO adjustments was made to
prevent underflows that occur when raising DPP ref clock (which is not
double-buffered), but that same decision causes similar issues when
lowering DPP global ref clock. The better solution is to order the
adjustments according to whether clocks are being raised or lowered.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Separating the hardware initialization from the creation of the
dc structures gives greater flexibility to the dm to override
options for debugging.
[How]
Move the hardware initialization call to a new function,
dc_hardware_init. No functional change is intended.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C write command always send mot = true will cause sink state incorrect.
[How]
1. Remove default i2c write mot = true.
2. Deciding mot flag by is_end_of_payload flag.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new implementation changed the behavior to allow process setMode
to DAL when DAL returns empty mode query for unplugged display.
This will trigger additional disable_link().
When unplug HDMI from MST dock, driver will update stream->signal to
"Virtual". disable_link() will call disable_output() if the signal type
is not DP and induce other displays on MST dock show black screen.
[How]
Don't need to process disable_output() if the signal type is virtual.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20_calculate_dlg_params was incorrectly indexing pipe src and
dst structs when extracting global sync params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Global sync update was missing vtg update resulting in underflow if
vstartup decreased a significant amount.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if YUV420 is available for video mode, YUV444 is still
automatically selected. This poses a problem for compliance tests.
[How]
Add a per-connector debugfs entry "force_yuv420_output" to force
selection of YUV420 mode.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Surface dchub/dpp update would not trigger if a stream update was the
only cause. This change now allows stream flags to trigger this update.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
A function to adjust DPP clocks with DTO already exists; function code
is identical to the code replaced here
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The issue is specific for linux, as on timings such as 8K@60
or 4K@144 DSC should be working in combination with ODM Combine
in order to ensure that we can run those timings. The validation
for those timings was passing, but when pipe split was happening
second pipe wasn't being programmed.
[how]
Rebuild mapped resources if we split stream for ODM.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current configuration 0 is just a placeholder, and final parameters needed.
Also, configuration 1 is expected to emulate ABM 2.1 but is too aggressive.
[How]
Redefine configuration 0 with the finalized parameters, and increase the
contrast gain of configuration 1 so that it properly emulates ABM 2.1.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Secondary viewport dimension/position registers are not programmed,
which can cause issues in some stereo configurations.
[How]
Add register definitions and register programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The placement is something TTM/BO internal and the RAS code should
avoid touching that directly.
Add a helper to create a BO at a fixed location and use that instead.
v2: squash in fixes (Alex)
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use debugfs_remove_recursive to remove the whole debugfs
directory instead of removing the node one by one.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is usfull for debugging.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Already done in the CPU based backend code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No functional change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit a213c2c7e2.
The changes to fix this should have landed in 5.1.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Zhou, David(ChunMing) <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With changes in PSP and HV, SRIOV VF will handle
vram gtt location just like bare metal. There is
no need to differentiate it anymore.
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These is no LBPW on Renoir. So removing program of lbpw for renoir.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ttmp[4:5] hold information useful to the debugger. Use ttmp[14:15]
instead, aligning implementation with gfx9 trap handler.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Reviewed-by: shaoyun liu <Shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
debugfs_remove and kfree has taken the null check in account.
hence it is unnecessary to check it. Just remove the condition.
No functional change.
This issue was detected by using the Coccinelle software.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is fine for displays without audio functionality to not provide
any SAD block in their EDID. Do not log an error in that case,
just return quietly.
Inspired by a similar fix to the amdgpu driver in the context of bug
fdo#107825:
https://bugs.freedesktop.org/show_bug.cgi?id=107825
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is fine for displays without audio functionality to not provide
any SAD block in their EDID. Do not log an error in that case,
just return quietly.
This fixes half of bug fdo#107825:
https://bugs.freedesktop.org/show_bug.cgi?id=107825
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not try to allocate any amount of memory requested by the user.
Instead limit it to 128 registers. Actually the longest series of
consecutive allowed registers are 48, mmGB_TILE_MODE0-31 and
mmGB_MACROTILE_MODE0-15 (0x2644-0x2673).
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111273
Signed-off-by: Trek <trek00@inbox.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bail from the pci_driver probe function instead of from the drm_driver
load function.
This avoid /dev/dri/card0 temporarily getting registered and then
unregistered again, sending unwanted add / remove udev events to
userspace.
Specifically this avoids triggering the (userspace) bug fixed by this
plymouth merge-request:
https://gitlab.freedesktop.org/plymouth/plymouth/merge_requests/59
Note that despite that being an userspace bug, not sending unnecessary
udev events is a good idea in general.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1490490
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in the variable name eanble,
rename it to enable.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit e01f2d4189.
VG20 did not require this workaround, as the fix is in the VBIOS.
Leave VG10/12 workaround as some older shipped cards do not have the
VBIOS fix in place, and the kernel workaround is required in those
situations
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Next step towards HMM support. For now just silence the retry fault and
optionally redirect the request to the dummy page.
v2: make sure the VM is not destroyed while we handle the fault.
v3: fix VM destroy check, cleanup comments
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Free the pasid only while the root PD is reserved. This prevents use after
free in the page fault handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While handling a page fault we can't wait for other ongoing GPU
operations or we can potentially run into deadlocks.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For handling PD/PT clears directly in the fault handler.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For handling PTE updates directly in the fault handler.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For handling PDE updates directly in the fault handler.
v2: fix typo in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows us to update page tables directly while in a page fault.
v2: use direct/delayed entities and still wait for moves
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For page fault handling we need to use a direct update which can't be
blocked by ongoing user CS.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting the no_gpu_wait flag means that the allocate BO must be available
immediately and we can't wait for any GPU operation to finish.
v2: squash in mem leak fix, rebase
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to make sure that we actually dropping the right fence.
Could be done with RCU as well, but to complicated for a fix.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In SRIOV case, the autoload sequence is the same
as bare metal, except VF won't load TOC.
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In SRIOV case, SMU and powerplay are handled in HV.
VF shouldn't have control over SMU and powerplay.
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The sdma_v4 should be ungated when the IP resume back,
otherwise it will hang up and resume time out error.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mailbox functions and interrupts are only for Navi12 VF.
Register functions and irqs during initialization.
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
psp v11 code missed ring stop in ring create function(VMR)
while psp v3.1 code had the code. This will cause VM destroy1
fail and psp ring create fail.
For SIOV-VF, ring_stop should not be deleted in ring_create
function.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is especially needed for non-psp loading way.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set mp1 state properly for SW SMU suspend/reset routine.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawaii needs to flush caches explicitly, submitting an IB in a user
VMID from kernel mode. There is no s_fence in this case.
Fixes: eb3961a574 ("drm/amdgpu: remove fence context from the job")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
amdgpu_ras_reserve_bad_pages was moved to amdgpu_ras_reset_gpu
because writing to EEPROM during ASIC reset was unstable.
But for ERREVENT_ATHUB_INTERRUPT amdgpu_ras_reset_gpu is called
directly from ISR context and so locking is not allowed. Also it's
irrelevant for this partilcular interrupt as this is generic RAS
interrupt and not memory errors specific.
Fix:
Avoid calling amdgpu_ras_reserve_bad_pages if not in task context.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mimic the ones for Vega10, add mailbox backend for Navi1x
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These registers will be accessed for querying ras errors.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add and_mask since the programming logic of golden setting changed
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
we only want the lowest voltage to be available for dali.
[How]
Use the get_highest_allowed_voltage_level function
to return 0 for dali
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dali is a new asic revision based on raven2
Add the ID and ASICREV_IS_DALI define
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The table grows quickly during debug/development effort when
multiple RAS errors are injected. Allow to avoid this by setting
table header back to empty if needed.
v2: Switch to debugfs entry instead of load time parameter.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow to reset the table on the fly.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
this interface is related to specific version of umc, distinguish it
from ras_late_init
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
move umc ras init from ras module to umc block, generic ras module
should pay less attention to specific ras block.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
umc late init is umc specific, it's more suitable to be put in umc block
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
define sched_policy in case CONFIG_HSA_AMD is not
enabled, with this there is no need to check for CONFIG_HSA_AMD
else where in driver code.
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If CONFIG_HSA_AMD is not set, build fails:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.o: In function `amdgpu_device_ip_early_init':
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1626: undefined reference to `sched_policy'
Use CONFIG_HSA_AMD to guard this.
Fixes: 1abb680ad371 ("drm/amdgpu: disable gfxoff while use no H/W scheduling policy")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also bump the SMU11_DRIVER_IF_VERSION_ARCT.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to perform DC-BTC for arcturus on bootup.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the ASIC specific code into a new callback function.
v2: mask the flags for SI and CIK instead of a BUG_ON().
v3: remove last missed BUG_ON().
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unify how we map the UAPI flags to the PTE hardware flags for a mapping.
Only the MTYPE is actually ASIC dependent, all other flags should be
copied over 1 to 1 and ASIC differences are handled later on.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to add asic flag to enable device probe during kfd init.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While gfxoff is enabled, the mmVM_XXX registers will be 0xfffffff while the GFX
is in "off" state. KFD queue creattion doesn't use ring based method, so it will
trigger a VM fault.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds renoir kfd topology which is the same with Raven.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir is the same with Raven, will enable iommu event in future.
v2: fix the checking (Thong)
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch inits renoir kfd device info, so we treat renoir as "dgpu"
(bypass iommu v2). Will enable needs_iommu_device till renoir iommu is ready.
v2: rebase and align the drm-next
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir's cache info should be the same with raven and carrizo's.
v2: fix missed "break"
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initial support of Navi14 in KFD. The device IDs will be added later.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no point retrying page faults in VMID0. Those faults are
always fatal.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-and-Tested-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As more and more new asics start to reuse the old device IDs before
launch, there is a need to quickly override the existing asic type
corresponding to the reused device ID through a kernel parameter. With
this, engineers no longer need to rely on local hack patches,
facilitating cooperation across teams.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to check if the nbios funcs exist before
checking the individual pointers.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
[Why]
DP1.2 LL CTS test failure.
[How]
The failure is caused by not verify stream link is equal
to link, only check stream and link is not null.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Underflow occurs on some display setups(repro'd on 3x4K HDR) on boot,
mode set, and hot-plugs with. Underflow occurs because mem clk
is not set high after disabling pstate switching. This behaviour occurs
because some calculations assumed displays were synchronized.
[How] Add a condition to check if timing sync is disabled so that
synchronized vblank can be set to false.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.
[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened
Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to add missing surface address register definitions.
- RGBE+A does not work in a stereo configuration because
surface addresses are no programmed correctly.
[How]
Added the register definitions and surface address programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's sometimes useful to have this option when debugging
[how]
Add a config flag. If the flag is not set, use driver default policy.
If the flag is set, use the value from the flag as the starting DSC slice
height.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The requirement has been clarified and only DSC 4:2:2 Native has to
be disabled.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should not allocate payloads if the link is lost until the link is retrained.
Some displays require this.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Driver defaults to 1-tap subsample mode for 4:2:2.
DCE11.2 added 3-tap. The policy is:
DCE8-DCE11 - change to 2-tap, it's better than 1-tap.
DCE11.2+ - use 3-tap
Note that 4:2:0 was added in DCE11.2 and already uses 3-tap always.
Note 2 is that DCE not covered on Linux, only DCN+
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.
1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.
[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML diags tests are failing because the struct contents get
clobbered by a memcpy.
[How]
Remove the memcpy call.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The issue was accidentally introduced recently.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras recovery_init should be called after ttm init,
bad page reserve should be put in front of gpu reset since i2c
may be unstable during gpu reset.
add cleanup for recovery_init and recovery_fini
v2: add more comment and print.
remove cancel_work_sync in recovery_init.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
save umc error records to ras bad page array
v2: add bad pages before gpu reset
v3: add NULL check for adev->umc.funcs
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
support eeprom records load and save for ras,
move EEPROM records storing to bad page reserving
v2: remove redundant check for con->eh_data
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
change bps type from retired page to eeprom table record, prepare for
saving umc error records to eeprom
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix typo which messed up the calculation.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-and-tested-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Restoring clock gating break SMU opeartion afterwards, avoid
this until this further invistigated with SMU.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-and-tested-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier patch "Hook up calls to do stereo mux and dig programming..."
doesn't include update for dcn21.
[How]
Align dcn21 gpio settings with updated stereo control interface.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This optimizes out the pci device id usage in KFD and makes the code
more maintainable.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These wptrs must be pinned and GPU accessible when this is called
from hqd_load functions. So they should never fault. This resolves
a circular lock dependency issue involving four locks including the
DQM lock and mmap_sem.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates MP1_BASE in renoir_ip_offset.h
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With the common interface print_clk_levels can get the following dpm clock:
-pp_dpm_dcefclk
-pp_dpm_fclk
-pp_dpm_mclk
-pp_dpm_sclk
-pp_dpm_socclk
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for loading XGMI/RAS FW
Signed-off-by: John Clements <john.clements@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
change r type from bool to int, suitable for both bool and int return
value
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix bellow patch issue:
drm/amd/powerplay: introduce smu table id type to handle the smu table
for each asic
----
"This patch introduces new smu table type, it's to handle the
different smu table
defines for each asic with the same smu ip."
before:
use smu->table_count to represent the actual table count in smc firmware
use actual table count to check smu function parameter about smu table
after:
use logic table count "SMU_TABLE_COUNT" to check function parameter
because table id already mapped in smu driver,
and smu function will use logic table id not actual table id to check func parameter.
v2: squash in warning fix
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add sw_fini interface of df_funcs.
This interface will remove sysfs file of df_cntr_avail
function.
The old behavior only create sysfs of df_cntr_avail
in sw_init, but never remove it for lack of sw_fini
interface. With this,driver will report create
sysfs fail when it's loaded for the second time.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Jonathan Kim <Jonathan.Kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_nbio_ras_late_init is used to init nbio specfic
ras debugfs/sysfs node and nbio specific interrupt handler.
It can be shared among nbio generations
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_mmhub_ras_late_init is used to init mmhub specfic
ras debugfs/sysfs node and mmhub specific interrupt handler.
It can be shared among mmhub generations
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_sdma_ras_late_init is used to init sdma specfic
ras debugfs/sysfs node and sdma specific interrupt handler.
It can be shared among sdma generations
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_gfx_ras_late_init is used to init gfx specfic
ras debugfs/sysfs node and gfx specific interrupt handler.
It can be shared among gfx generations
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_gmc_ras_late_init is used to init gmc specfic
ras debugfs/sysfs node and gmc specific interrupt handler.
It can be shared among gmc generations.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to prevent access to dangling pointers
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of RAS error allow user configure auto system
reboot through ras_ctrl.
This is also part of the temproray work around for the RAS
hang problem.
v4: Use latest kernel API for disk sync.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
Under certain conditions, when some IP bocks take a RAS error,
we can get into a situation where a GPU reset is not possible
due to issues in RAS in SMU/PSP.
Temporary fix until proper solution in PSP/SMU is ready:
When uncorrectable error happens the DF will unconditionally
broadcast error event packets to all its clients/slave upon
receiving fatal error event and freeze all its outbound queues,
err_event_athub interrupt will be triggered.
In such case and we use this interrupt
to issue GPU reset. THe GPU reset code is modified for such case to avoid HW
reset, only stops schedulers, deatches all in progress and not yet scheduled
job's fences, set error code on them and signals.
Also reject any new incoming job submissions from user space.
All this is done to notify the applications of the problem.
v2:
Extract amdgpu_amdkfd_pre/post_reset from amdgpu_device_lock/unlock_adev
Move amdgpu_job_stop_all_jobs_on_sched to amdgpu_job.c
Remove print param from amdgpu_ras_query_error_count
v3:
Update based on prevoius bug fixing patch to properly call amdgpu_amdkfd_pre_reset
for other XGMI hive memebers.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue 1:
In XGMI case amdgpu_device_lock_adev for other devices in hive
was called to late, after access to their repsective schedulers.
So relocate the lock to the begining of accessing the other devs.
Issue 2:
Using amdgpu_device_ip_need_full_reset to switch the device list from
all devices in hive to the single 'master' device who owns this reset
call is wrong because when stopping schedulers we iterate all the devices
in hive but when restarting we will only reactivate the 'master' device.
Also, in case amdgpu_device_pre_asic_reset conlcudes that full reset IS
needed we then have to stop schedulers for all devices in hive and not
only the 'master' but with amdgpu_device_ip_need_full_reset we
already missed the opprotunity do to so. So just remove this logic and
always stop and start all schedulers for all devices in hive.
Also minor cleanup and print fix.
v4: Minor coding style fix.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trying to evict things from the current working set doesn't work that
well anymore because of per VM BOs.
Rely on reserving VRAM for page tables to avoid contention.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This hopefully helps reduce the contention for page tables.
v2: adjust maximum reported VRAM size as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make VM updates depend on the moving fence instead of the exclusive one.
Makes it less likely to actually have a dependency.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are needed for smu_reset support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to update in cache feature enablement status after pp_feature
settings. Another fix for the commit below:
drm/amd/powerplay: implment sysfs feature status function in smu
V2: update smu_feature_update_enable_state() and relates
V3: use bitmap_or and bitmap_andnot
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Force clock level is for dpm manual mode only.
Reported-by: Candice Li <candice.li@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gds clearing workaround should only be applied on asics that support gfx ras
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
free ras_if if ras is not supported
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mmhub callback functions are not initialized for all the ASICs
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This workaround is better handled in user mode in a way that doesn't
require allocating extra memory and breaking userptr BOs.
The TLB bug is a performance bug, not a functional or security bug.
Hence it is safe to remove this kernel part of the workaround to
allow a better workaround using only virtual address alignments in
user mode.
v2: Removed VI_BO_SIZE_ALIGN definition
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For compute VRAM allocations on Arturus use the new RW mtype
for non-coherent local memory, CC mtype for coherent local
memory and PTE_SNOOPED bit for invalidating non-dirty cache
lines on remote XGMI mappings.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The same BO can be mapped with different PTE flags by different GPUs.
Therefore determine the PTE flags separately for each mapping instead
of storing them in the KFD buffer object.
Add a helper function to determine the PTE flags to be extended with
ASIC and memory-type-specific logic in subsequent commits.
v2: Split Arcturus-specific MTYPE changes into separate commit
v3: Fix return type of get_pte_flags to uint64_t
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Arcturus repurposed mtype WC to RW. Modify gmc functions
to support the new mtype
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call helper function in late init phase to handle ras init
for nbio ip block
v2: init local var r to 0 in case the function return failure
on asics that don't have ras_late_init implementation
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras_late_init callback function will be used to do common ras
init in late init phase.
v2: call ras_late_fini to do cleanup when fails to enable interrupt
v3: rename sysfs/debugfs node name to pcie_bif_xxx
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function will be called in late init phase to do mmhub
ras init
v2: check ras_late_init function pointer before invoking the
function
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call helper function in late init phase to handle ras init
for gmc ip block
v2: call ras_late_fini to do clean up when fail to enable interrupt
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call helper function in late init phase to handle ras init
for sdma ip block
v2: call ras_late_fini to do clean up when fail to enable interrupt
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call helper function in late init phase to handle ras init
for gfx ip block
v2: call ras_late_fini to do clean up when fail to enable interrupt
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In late_init for ras, the helper function will be used to
1). disable ras feature if the IP block is masked as disabled
2). send enable feature command if the ip block was masked as enabled
3). create debugfs/sysfs node per IP block
4). register interrupt handler
v2: check ih_info.cb to decide add interrupt handler or not
v3: add ras_late_fini for cleanup all the ras fs node and remove
interrupt handler
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the hardware that can not enable BIF ring for IH cookies for both
ras_controller_irq and err_event_athub_irq, the driver has to poll the
status register in irq handling and ack the hardware properly when there
is interrupt triggered
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ras controller interrupt and Ras err event athub interrupt are two dedicated
interrupts for RAS support.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add mmBIF_INTR_CNTL and its shift mask.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras_controller_interrupt and err_event_interrupt are ras specific interrupts.
add functions to check their status and ack them if they are generated. both
funcitons should only be invoked in ISR when BIF ring is disabled or even not
initialized.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
no functional change, just switch to new structures
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
More nbio funcitonalities will be added and nbio could
be treated as an ip block like gfx/sdma.etc
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.4-2019-08-30:
amdgpu:
- Add DC support for Renoir
- Add some GPUVM hw bug workarounds
- add support for the smu11 i2c controller
- GPU reset vram lost bug fixes
- Navi1x powergating fixes
- Navi12 power fixes
- Renoir power fixes
- Misc bug fixes and cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830212650.5055-1-alexander.deucher@amd.com
Add the missing unlock before return from function etnaviv_iommuv1_context_alloc()
in the error handling case.
Fixes: 27b67278e0 ("drm/etnaviv: rework MMU handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
There was a few uses of drmP that was missed in the last
patch removing this header from exynos.
Remove the final uses of this header.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Null pointer dereference check should have been checked,
ahead of below routine.
struct amdgpu_device *adev = hwmgr->adev;
With this commit, it could avoid potential NULL dereference.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is missing "if defined" CONFIG_DRM_AMD_DC block for non DC
configurations. This will cause link error. The patch is fixing that.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=110979
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In renoir's vega10_ih model, there's a security change in mmIH_CHICKEN
register, that limits IH to use physical address (FBPA, GPA) directly.
Those chicken bits need to be programmed first.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In Renoir's emulator, those chicken bits need to be programmed.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For apu, SMU_MSG_OverridePcieParameters is unsupport.
So return directly in smu_override_pcie_parameters function.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be checked at all places job is accessed.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DC support for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up the DML changes for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for renoir first.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a kconfig option to enable renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the building of dcn21 support.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing parameters, to make dcn21 compile
without errors
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the rev id for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call update_bw_bounding_box in DC construct
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up renoir support to KMS.
v2: squash in "Fixes for Renoir in amdgpu_dm"
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add Renoir DCN version in DC and handle it
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rename VM_CONTEXT0 to MMVM_CONTEXT0 as that is the name defined in
the register files
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML provides the display configuration validation as provided
by the hw teams.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
