The patch is to fix typo of the Layerscape SCFG MSI dts compatible
strings. "1" is replaced by "l".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds the device tree binding documentation for the mediatek thermal
controller found on Mediatek MT2712.
Signed-off-by: Louis Yu <louis.yu@mediatek.com>
Reviewed-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In aic3x class of devices Output Common-Mode Voltage can be configured for
better analog performance.
The OCMV value depends on the Analog and digital domain power supply
voltage configuration.
The default OCMV of 1.35V gives best performance when AVDD is around 2.7V
and DVDD is 1.525V, but for higher AVDD/DVDD higher OCMV setting is
recommended.
The patch gives an automatic way of guessing the best OCMV which can be
overwritten by a DT parameter if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the binding documentation for Spreadtrum SC9860 pin
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some scenarios, we should set some pins as input/output/pullup/pulldown
when the specified system goes into deep sleep mode, then when the system
goes into deep sleep mode, these pins will be set automatically by hardware.
That means some pins are not controlled by any specific driver in the OS, but
need to be controlled when entering sleep mode. Thus we introduce one sleep
state config into pinconf-generic for users to configure.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HSDK board manages its clocks using various PLLs. These PLL have same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on HSDK board consists of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
HSDK arc cpus, system, ddr, AXI tunnel and hdmi.
By this patch we add support for several plls (arc cpus pll and others),
so we had to use two different init types: CLK_OF_DECLARE for arc cpus pll
and regular probing for others plls.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Implement vas_init() and vas_exit() functions for a new VAS module.
This VAS module is essentially a library for other device drivers
and kernel users of the NX coprocessors like NX-842 and NX-GZIP.
In the future this will be extended to add support for user space
to access the NX coprocessors.
VAS is currently only supported with 64K page size.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Marvell Armada 7K/8K SoCs contains an hardware block called COMPHY
that provides a number of shared PHYs used by various interfaces in the
SoC: network, SATA, PCIe, etc. This Device Tree binding allows to
describe this COMPHY hardware block.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add internal PCI bridge support for r8a7743/5 SoC. The Renesas RZ/G1[ME]
(R8A7743/5) internal PCI bridge is identical to the R-Car Gen2 family.
This doesn't change the driver, so it does nothing by itself. But it does
mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7743" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
[bhelgaas: add explanatory note]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Document STM32 VREFBUF (voltage reference buffer) which can be used as
voltage reference for ADCs, DACs and external components.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Nodes without reg properties must not have unit addresses:
Warning (unit_address_vs_reg): Node .../rcar_sound,dvc/dvc@0 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add controller support for MT2712/MT7622 and update related properties.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
To accommodate other SoC generations, regroup specific properties by SoC,
and remove redundant descriptions.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split into a rename patch and a cleanup patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
To accommodate other SoC generations, rename mediatek,mt7623-pcie.txt to
mediatek-pcie.txt.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split rename to separate patch so updates are obvious]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5) SDHI
is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The third MMC controller (MMC2) on the Allwinner A83T SoC is slightly
different. It supports a wider 8-bit bus, has a dedicated controllable
reset pin for eMMC, and a "new timing mode" which is supposed to deliver
better signals and thus better performance.
Add a compatible for this one to use the new timing mode not found in the
other controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Add description for a new family SoC from Marvell: Armada-8KP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmeipsACgkQCwYYjhRyO9UnEACcDuFAUJNT2eth5lYMHoHcvMLf
x7QAnjqghjBpm7nYOutsYPY5gwz/YYC6
=+kES
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 3)
Add description for a new family SoC from Marvell: Armada-8KP.
* tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Device Tree files for Armada-8KP
Signed-off-by: Olof Johansson <olof@lixom.net>
The ls2088a PCIe controller's register addresses are different from
ls2080a, so add a match entry to identify ls2088a PCIe.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Update description for newly added optional audio codecs.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Baseboard Management Controller (BMC) systems it's sometimes
necessary for a LED to retain its state across a BMC reset (which is
independent of the host system state). Add a devicetree property to
describe this behaviour. The property would typically be used in
conjunction with 'default-state = "keep"'.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This adds the devicetree bindings for the PCA955x I2C LED blinkers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Deprecate the legacy Rockchip PCIe PHY and encourage users to use per-lane
PHY mode by setting #phy-cells to 1.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Deprecate legacy PHY model and encourage per-lane PHY model.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Commit b053dc5a72 (powerpc: Refactor device tree binding) split the
Ethernet PHY binding documentation out of the big booting-without-of.txt
file, leaving a dangling reference to "section 2" in the 'interrupts'
property description. Drop that reference, and make the description look
more like the rest.
While at it, make the example interrupt-parent phandle look more like a
real world phandle, and use an IRQ_TYPE_ macro for the 'interrupts'
type.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Add DT bindings for the onboard SATA controller present on the MediaTek
SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the binding documentation for Spreadtrum I2C
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The deprecated DT properties are part of the GIT history,
no need to keep them around any longer.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove the 32-bit CMT compat strings to reduce maintenance burden.
It should be fine to break DT compatibility because the 32-bit
CMT DT binding was never part of any upstream DTS file.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add documentation for new separate CMT0 and CMT1 DT compatible strings
for R-Car Gen2. These compat strings allow us to enable CMT1-specific
features in the driver. The old compat strings will be deprecated in
the not so distant future.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove the sh7372 CMT compat string to reduce maintenance burden.
It should be fine to break DT compatibility because:
1) The sh7372 SoC support has been removed from upstream
2) The sh7372 CMT DT binding was never part of upstream DTS
3) The CMT driver never matches on the sh7372 binding
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Document the devicetree bindings in 8250.txt for MediaTek BTIF
controller which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document support for the (H)SCIF serial ports in the Renesas R-Car D3
(r8a77995) SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver provides PS/2 serio bus support by implementing bit banging
with the GPIO API. The GPIO pins, data and clock, can be configured with
a node in the device tree or by generic device properties (GDP).
Writing to a device is supported as well, though it is possible timings
can not be halt as they are tough and difficult to reach with bit banging.
Therefore it can be configured (also in DT and GDP) whether the serio
write function should be available for clients.
This driver is for development purposes and not recommended for productive
use. However, this driver can be useful e.g. when no USB port is available
or using old peripherals is desired as PS/2 controller chips getting rare.
This driver was tested on bcm2825 and on Kirin 960 and it worked well
together with the atkbd and psmouse driver.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
Document in the Device Tree binding document that this manufacturer should
be used as the generic fallback. Also document the deprecated vendors.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the below warning
--> Use #include <linux/io.h> instead of <asm/io.h>
--> Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
--> please, no space before tabs
--> Block comments use a trailing */ on a separate line
--> Possible unnecessary 'out of memory' message
--> Block comments use * on subsequent lines
--> Block comments use a trailing */ on a separate line
--> braces {} are not necessary for any arm of this statement
--> DT compatible string "xlnx,opb-hwicap-1.00.b"
appears un-documented
--> DT compatible string "xlnx,xps-hwicap-1.00.a"
appears un-documented
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZn3XJAAoJEJzN3yze689Tat0P/jnTEqEleNCDBYx4SW/c7ilO
KCNXEEfgtD0sIon3KPt6Zbc0Na+QmD7DSrdlPsc0864k7Vrb/M+bshETtrxC/fQi
WW8SaRHNLePCH0UnayUoukYtlui1zWbfdJ8HLQqfQILQy2LVIaA7famL8wuHHXJR
4zl69EQPTODBKt9akHjQ2pLuucN/6KAl4QcBje4eY/c+mMpyjo6Ivi6vRCFpL66T
J+rBobTvRoMUwTaIlmquwoVgdMpk2DA9NXOypGT3slIeIqfyUf+7TUtBGbVrCmvj
o+zVap5pcZhf6KXfi4OZUbDdgXpIn2V1p5ztAq0JlW2LcyguZ1bZs3EJAsyRS0aS
3ykru6e5KqH4vcMwcxkgatPKhSSPyC93ETdvx55IF7uP6qH8ym1hgtDKr7FrPW0+
Md/gO8YPgFMZRUG2rAbCJO/zFbS4aNh0X6eOOCmsraxy0IQBE/p41zw8Tp7Jgupv
oxV1beXyB2DLBCGkj12baGUzePZent/vse3dPbl8YHiubQCgAa4u4NO70EU/T9W+
3PeJEK4o3vw9aDBGTMINRUSMKQGCAkf4VL+wyBn8k/LTYWPP1YsA1+beX1E184vB
vS0nnjhJP8VphfAAx5+eYnep6HPTUPwlyi9CR/vbSG8HmPkfIDslQ8700VsmsEkn
6mMDK+pd9FGjs6nwwO5d
=oQMu
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.14
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This binding still doesn't please everyone, and we're getting far too
close from the release to allow it to reach a stable version.
Let's remove it until the discussion settles down.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add MT7622 i2c binding to binding file. Compare to MT8173 i2c
controller, MT7622 limits message numbers to 255, and does not
support 4GB DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use common name MediaTek and modify the compatible information
formats of all SoCs to the same.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Document DT bindings for Analog Devices as3645a flash LED controller which
also supports an indicator LED.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Dongwoon DW9714 is a voice coil lens driver.
Also add a vendor prefix for Dongwoon for one did not exist previously.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This adds the necessary data for handling io voltage domains on the RV1108.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support to the keystone remoteproc driver for managing the
DSP present in the Keystone 2 66AK2G SoC. The 66AK2G SoC has
a Power Management Micro Controller (PMMC) that manages the
individual device's power, clock and reset functionalities.
The keystone remoteproc driver already uses standard frameworks
for reset and clock control, so it doesn't require any significant
modifications other than a new compatible suitable for 66AK2G DSP.
The binding document is also updated to reflect the modified
property values used by the 66AK2G DSP node as compared to the
values used by existing Keystone 2 DSPs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the device tree bindings document for the DSP processor
subsystem devices on TI Davinci DA8xx/OMAP-L13x SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the IPQ8074 PCIe controller. IPQ8074 supports Gen 1/2, one
lane, two PCIe root complex with support for MSI and legacy interrupts, and
it conforms to PCI Express Base 2.1 specification.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdnagQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSpBB/9v6flM/QtBVeXhR1tfrXIt3veUaiwiTwhg
PIj6J7EJZCgA9TiHr4zcQzjCx581a9v1rUEpnhZyi7d/zrNurpJRYtBNcqfDS28Z
kyL30gwf/y4nVAzgIODGMNRWe3+IETNCIRZ236cV7jr9HgKmHvA0qc2aMzjHPMCF
XS9wPXgEW1kYIgKqzq1drAWY3iVB0W37KMX9HKVQfAlPcGu5jobk0lruQBZV0InH
8NR3NB9a7eknzPejmBO2ga0idS0oAc/eFQ8h2bHrxWVm1JO+2QDc7epxWCTmxBcP
DLy+7tuQiXEFc25AM3QpW97pJuqDT+zeZXd/F5BK5uGnpH63SNbi
=D65g
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "second round of Rockchip dts64 changes for 4.14" from Heiko Stübner:
3 new boards, the rk3328-based Rock64 from the Pine64-makers, the
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
* tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
arm64: dts: rockchip: add rk3328-rock64 board
arm64: dts: rockchip: add rk3328 pdm node
arm64: dts: rockchip: add more rk3399 iommu nodes
arm64: dts: rockchip: add rk3368 iommu nodes
arm64: dts: rockchip: add rk3328 iommu nodes
arm64: dts: rockchip: Add basic cpu frequencies for RK3368
arm64: dts: rockchip: add rk805 node for rk3328-evb
arm64: dts: rockchip: Assign mic irq to correct device for Gru
arm64: dts: rockchip: init rk3399 vop clock rates
arm64: dts: rockchip: Add pwm nodes for rk3328
arm64: dts: rockchip: Fix wrong rt5514 dmic delay property for Gru
arm64: dts: rockchip: disable tx ipgap linecheck for rk3399 dwc3
arm64: dts: rockchip: remove num-slots property from rk3399-sapphire
arm64: dts: rockchip: Enable tsadc module on RK3328 eavluation board
arm64: dts: rockchip: add thermal nodes for rk3328 SoC
arm64: dts: rockchip: add tsadc node for rk3328 SoC
arm64: dts: rockchip: add rk3328 i2s nodes
...
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdoA4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeBtB/9oM4MmVRJ0YX7hk4NuU9c4HHdvCW0f1rJe
Q6rE6dP7fW3J27d6PuySVWzvIBmD+3xVA2t0dDm85DIP8f1DFz3vyNhkEsu1VG89
MULTektihczugCy+sh3iHILs4fLXJ8QUjCKJWOcWmZHOaXNXXjJIVjC97m5F4ZAj
KVOYXNnCKdaHYIeP0lkjStL8Z9Ua7svkjfgsSPTGTSJQQ+bGcd/8JnmlkzjfHWLw
qNz6M7FPoJ1rAffskr1At27oRs7UAVSKNAejl8DWKvLXml6NQPRRRu99sLLanxII
3b6LsC6Vwea4a1Rjwx0LZWdDUtB1W34/ZIEw4JceK/i6HfV5K2Oi
=di6U
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "second round of Rockchip dts32 changes for 4.14" from Heiko Stübner:
A lot of attention for the rv1108 soc targetted at media-processing
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
* tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: rockchip: add cpu power supply for rv1108 evb
ARM: dts: rockchip: add cpu opp table for rv1108
ARM: dts: rockchip: add rk322x iommu nodes
ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evb
ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evb
ARM: dts: rockchip: add pwm backlight for rv1108 evb
ARM: dts: rockchip: add pwm dt nodes for rv1108
ARM: dts: rockchip: add spi dt node for rv1108
ARM: dts: rockchip: add saradc support for rv1108
ARM: dts: rockchip: add watchdog dt node for rv1108
ARM: dts: rockchip: add i2c dt nodes for rv1108
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
ARM: dts: rockchip: add more iommu nodes on rk3288
ARM: dts: rockchip: convert rk3288 device tree files to 64 bits
ARM: dts: rockchip: add spi node and spi pinctrl on rk3228/rk3229
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner A10 is now driven by sunxi-ng CCU driver.
Add devicetree binding for it.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A20 is now driven by sunxi-ng CCU driver.
Add devicetree binding for it.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- Add more module clocks for R-Car V2H and M3-W,
- Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
- Add support for the new R-Car D3 SoC,
- Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=77l6
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
* Add more module clocks for R-Car V2H and M3-W,
* Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
* Add support for the new R-Car D3 SoC,
* Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
* Small fixes and cleanups.
* tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add USB3.0 clock
clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY
clk: renesas: cpg-mssr: Add R8A77995 support
clk: renesas: rcar-gen3: Add support for SCCG/Clean peripheral clocks
clk: renesas: rcar-gen3: Add divider support for PLL1 and PLL3
clk: renesas: Add r8a77995 CPG Core Clock Definitions
clk: renesas: rcar-gen3-cpg: Refactor checks for accessing the div table
clk: renesas: rcar-gen3-cpg: Drop superfluous variable
clk: renesas: Allow compile-testing of all (sub)drivers
clk: renesas: r8a7792: Add IMR-LX3/LSX3 clocks
clk: renesas: div6: Document fields used for parent selection
Rockchip socs experience with the default approximation. For that we
introduce the ability to override it with a clock-specific approximation
and use that to create the needed rate settings as described in the
Rockchip soc manuals (same for all Rockchip socs).
Apart from that we have support for the rk3126 clock controller
which is similar to the rk3128 with some minimal differences
and a lot of improvements and fixes for the rv1108 clock controller
(missing clocks, some clock-ids, naming fixes, register fixes).
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmcl8sQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeiBB/wIf5LHDu09HuOb1bjtYASMc//ve2ymhpd7
QsccJ0nteJTWnYQlrJUPYN8YhRVqPNrz7Fq8PkMMkzm89fQQ6lr5DxOy6olKTPM4
sGf+242eE3XttHjJxcshNPS98A56zBa9OgNC9sUsTex8r7NaJn+Gvlf0sXEgQRQi
5FprJf49/4rlHZypVMg1j+aMEWM8ZAmXLP3F77Qch+rfxE74POV9/HI7EEoSQ9MX
TxwEewmM8IGXY9aVTvtADPmX31CgdOD3qm4giwGkBf2F8SajP8R63wi+BYpNfUTX
+TrexLXEfeKEVtU+xPXsNYmEnAOW6sRvfyUnq4oA1hVSnFoexFA1
=Upwy
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk driver updates from Heiko Stuebner:
The biggest change is fixing the jitter on the fractional clock-type
Rockchip socs experience with the default approximation. For that we
introduce the ability to override it with a clock-specific approximation
and use that to create the needed rate settings as described in the
Rockchip soc manuals (same for all Rockchip socs).
Apart from that we have support for the rk3126 clock controller
which is similar to the rk3128 with some minimal differences
and a lot of improvements and fixes for the rv1108 clock controller
(missing clocks, some clock-ids, naming fixes, register fixes).
* tag 'v4.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix the rv1108 clk_mac sel register description
clk: rockchip: rename rv1108 macphy clock to mac
clk: rockchip: add rv1108 ACLK_GMAC and PCLK_GMAC clocks
clk: rockchip: add rk3228 SCLK_SDIO_SRC clk id
clk: rockchip: add rv1108 ACLK_GAMC and PCLK_GMAC ID
clk: rockchip: add rk3228 sclk_sdio_src ID
clk: rockchip: add special approximation to fix up fractional clk's jitter
clk: fractional-divider: allow overriding of approximation
clk: rockchip: modify rk3128 clk driver to also support rk3126
dt-bindings: add documentation for rk3126 clock
clk: rockchip: add some critical clocks for rv1108 SoC
clk: rockchip: rename some of clks for rv1108 SoC
clk: rockchip: fix up some clks describe error for rv1108 SoC
clk: rockchip: support more clks for rv1108
clk: rockchip: fix up the pll clks error for rv1108 SoC
clk: rockchip: support more rates for rv1108 cpuclk
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
Usual improvements:
- Added support for fixed post-divider on divider and NKM-style clocks
- Added driver for R40 CCU
Non critical fixes (from round 1):
- Fix sunxi-ng/ccu-sunxi-r.h header file guard macro typo
- Make fractional clock modes really used and correctly configured
- Make H3 cpu clock rate change correctly to be used with cpufreq
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEE2nN1m/hhnkhOWjtHOJpUIZwPJDAFAlmaR6AOHHdlbnNAY3Np
ZS5vcmcACgkQOJpUIZwPJDC8YA//aLULoosISnyHs+wKowVHuDb7/mQ82O1gOAxC
oE/vscd/WCRm7A5tfy+xHfajX/YRf32Qc09wB7fxUF4R0lgkO9QjUO0yX74a6bPh
HCh/+bcmeNl9TZAYpTs72Q4nfc1x63OZwxMqTRnBmh3cevyIBJiFvqPjoMeD+Ari
n32QEBgGE+A8bWshVFpNFyId6iyfMfozSYninIkVkwMGr7QgBgJRK1/5sftyZMR+
NQ2IGkaUfICnXofF//pNKsH7TN770gyDtFVWjrKZMrEKoP+gp3mawzMpfePKH/O6
4ihcm5LOo1Kdg5UzRTpQ2B/9fNUn2EvFYT6RuIBfddQcaflT1AzWtNK52j2L/crD
tFyamcCSsNY5LzeySbVW+pQMRfrq6UCYtssiL7HYEcwMzvv61PfyDtKq5dxtJd0Q
W8S6wPE/foj0i0JQWs0K70AacGU6XdEanUAtc5r3AsniCwwOtlwnaQqOlE5CiwAo
HOSItOxX4Y/9QglnntsDyhNUaKpaSiG21XdE3ho3xq1/CS9ED3p5Ljbshem5fnPi
mPisF6Ca6NVvCZ+sjH2RVvmGyh3d+BPfQLWC/sTamC4rnpDalrMq6IsCOivzbxqQ
ltkYwUO1nmz5NMloeWYCUWWmLUOECCQu7Mppf2UQxpidrEEY0mbBYFdOlehrlHZT
bWt2NdQ=
=DKSp
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next
Pull Allwinner clock changes from Chen-Yu Tsai:
* Added support for fixed post-divider on divider and NKM-style clocks
* Added driver for R40 CCU
* Fix sunxi-ng/ccu-sunxi-r.h header file guard macro typo
* Make fractional clock modes really used and correctly configured
* Make H3 cpu clock rate change correctly to be used with cpufreq
* tag 'sunxi-clk-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: support R40 SoC
dt-bindings: add compatible string for Allwinner R40 CCU
clk: sunxi-ng: nkm: add support for fixed post-divider
clk: sunxi-ng: div: Add support for fixed post-divider
dt-bindings: clock: sunxi-ccu: Add compatibles for sun5i CCU driver
clk: sunxi-ng: allow set parent clock (PLL_CPUX) for CPUX clock on H3
clk: sunxi-ng: h3: gate then ungate PLL CPU clk after rate change
clk: sunxi-ng: Wait for lock when using fractional mode
clk: sunxi-ng: Make fractional helper less chatty
clk: sunxi-ng: multiplier: Fix fractional mode
clk: sunxi-ng: Fix fractional mode for N-M clocks
clk: sunxi-ng: Fix header guard of ccu-sun8i-r.h
1. Qualcom IPQ4019 SoC uses QPIC NAND controller version 1.4.0
which uses BAM DMA Engine while IPQ806x uses EBI2 NAND
which uses ADM DMA Engine.
2. QPIC NAND will 3 BAM channels: command, data tx and data rx
while EBI2 NAND uses only single ADM channel.
3. CRCI is only required for ADM DMA and its not required for
BAM DMA.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Correct the compatible string for IPQ806x
2. Change the NAND controller and NAND chip nodes name
for more clarity.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.
Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
RK3399-Q7 is a Qseven compatible system-on-module by Theobroma Systems.
This adds the module and the EVK baseboard "Haikou"
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the compatible of GRF and USBGRF for RV1108 SoCs.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
TI AMC6821 fan controller and Intersil ISL1208 are trivial
devices, so add them to the binding list.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Theobroma Systems is a design house specialized in embedded systems
and a manufacturer of system-on-modules.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch documents the new marvell,system-controller property used by
the Marvell ppv2 network driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SckR
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.14
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It only supports rmii interface. Add constants and callback functions
for the dwmac on rv1108 socs. As can be seen, the base structure is
the same, only registers and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas RZ/G1E (R8A7745) SoC GPIO blocks are identical to the R-Car Gen2
family. Add support for its GPIO controllers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xgLM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.14
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
Document the device tree bindings for the ARTPEC crypto accelerator on
ARTPEC-6 and ARTPEC-7 SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds support usb2-phy for rv1108 SoCs and amend phy Documentation.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add otg-mux property to support multiplexed interrupt in otg-port
on some Rockchip SoC (e.g RV1108).
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add rockchip,usbgrf property to support the registers of usb-phy
that are distributed in grf and usbgrf on some special Rockchip
SoCs (e.g RV1108).
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The A83T has 3 USB PHYs, 1 for OTG, 1 for standard USB, 1 for USB HSIC.
Add a compatible string for it, and describe the needed properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Allwinner H3 SoC has 4 USB PHYs, so it needs four sets of pmu
regions, clocks, resets, and optional vbus properties. These were
not described when the H3 compatible string was added.
Fixes: 626a630e00 ("phy-sun4i-usb: Add support for the host usb-phys
found on the H3 SoC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MBHC (MultiButton Headset Control) support is available in pm8921 in two
blocks, one to detect mechanical headset insertion and removal and other
block to support headset type detection and 5 button detection and othe
features like impedance calculation.
This patch adds support to:
1> Support to NC and NO type of headset Jacks.
2> Mechanical insertion and detection of headset jack.
3> Detect a 3 pole Headphone and a 4 pole Headset.
4> Detect 5 buttons.
Tested it on DB410c with Audio Mezz board with 4 pole and 3 pole
headset/headphones.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bindings in DT to provide required micbias voltage which
could be specific to board. With this new binding, now the mic bias
voltage is left at hardware default value if the device tree does not
specify any mic bias voltage value. Correct micbias value is required
for mbhc buttons to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sun8i-h3 introduces a lot of changes to the i2s block such
as different register locations, extended clock division and
more operational modes. As we have to consider the earlier
implementation then these changes need to be isolated.
None of the new functionality has been implemented yet, the
driver has just been expanded to allow it work on the H3 SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
pdm sdi0~3 pins are optional, for example, if 4ch required,
only sdi0~1 need to be enabled.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enhance the MediaTek PWM binding with details about the IP found in the
MT2712 and MT7622 SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add device tree bindings documentation for Rockchip's RK805 PMIC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usual driver changes:
- SUNXI_RSB bus driver enabled by default for ARM64
- Support for SRAM controller and SRAM C block on the A64 added
-----BEGIN PGP SIGNATURE-----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=i+D6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/drivers
Pull "Allwinner driver changes for 4.14" from Chen-Yu Tsai:
Usual driver changes:
- SUNXI_RSB bus driver enabled by default for ARM64
- Support for SRAM controller and SRAM C block on the A64 added
* tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
Add a new compatible string "ti,k2g-ecap" to support PWM ECAP IP of
TI 66AK2G SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It adds bindings document for ZTE ZX PWM controller. The device has two
clocks: PCLK and WCLK. The PCLK is for register access, and WCLK is the
reference clock for calculating period and duty cycles. Also, the device
supports polarity configuration, so #pwm-cells should be 3.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
We need to increase the pwm-cells for the optional flags parameter,
before we can implement support for polarity setting via DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A few changes, but most notably improving the HDMI support merged in 4.13,
by reporting the DDC adapter as an i2c bus, and by adding CEC support
through the CEC framework.
-----BEGIN PGP SIGNATURE-----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=6GJs
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drm-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
Allwinner DRM changes for 4.14
A few changes, but most notably improving the HDMI support merged in 4.13,
by reporting the DDC adapter as an i2c bus, and by adding CEC support
through the CEC framework.
* tag 'sunxi-drm-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
sun4i_hdmi: add CEC support
dt-bindings: display: sunxi: Improve endpoint ID scheme readability
drm/sun4i: tcon: remove unused function
drm/sun4i: Remove useless atomic_check
drm/sun4i: Add if statement instead of depends on
drm/sun4i: hdmi: Implement I2C adapter for A10s DDC bus
drm/sun4i: constify drm_plane_helper_funcs
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
It adds the dt-bindings document for ZTE ZX IRDEC remote control
block.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document the device tree bindings for the GPIO IR Bit Banging
Transmitter.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document the device tree bindings for the PWM IR Transmitter.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document the devicetree bindings for CIR on MediaTek MT7622
SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a binding for the USB phy on Mediatek/Ralink SoCs.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
add support for PCIe and SATA, also add some new compatibles.
due to phy-mt65xx-usb.txt holds the bindings for all mediatek SoCs
with T-PHY controller, change the name to phy-mtk-tphy.txt to
reflect that.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
IPQ8074 uses QMP PHY controller that provides support to PCIe and
USB. Adding DT binding information for the same.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The PHY outputs a clock that will act as the parent for
the PHY's pipe clock. Add the name of this clock to the
lane's DT node.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner R40 has a clock controlling unit like the ones on other
Allwinner SoCs after sun6i, and can also use a CCU-based driver.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
- constify zx2967 reset_ops
- add a convenience API to manage an array of resets
- let deassert report success and let assert report success for shared resets
if the reset controller driver does not implement (de)assert.
- add HSDKv1 reset driver
- remove Gemini reset controller, the driver is made obsolete
by a combined clock/reset driver in drivers/clk
- fix the total number of reset lines in the sunxi driver
- various uniphier updates and fixes:
- remove sLD3 SoC support
- simplify system reset register and bit definitions
- add audio systems, video input subsystem, and analog amplifiers reset
controls
-----BEGIN PGP SIGNATURE-----
iQJMBAABCAA2FiEEBsBxhV1FaKwXuCOBUMKIHHCeYOsFAlmWg5MYHHBoaWxpcHAu
emFiZWxAZ21haWwuY29tAAoJEFDCiBxwnmDrEqoQAKSQDhwA5ZyBd216PoUSaLqf
tTGrJc/atfs+cDiqSyQDQ5vN0dTMnPV+YjGmwITg55ZGQTJRTq5nVhwM6y0CaASN
PE7U/9Ma/8GWOjtC+6hun6tAHeuX3fMq2cYK8BSL+D7MQr+zkIgEQx3YsbR/0Np7
qmawpZSKAvIxrpVkQiVrsxmVvxi23GdncGUPDHtKhAW4N1T3ywogpW/7t6AcDZZl
XIa09fIRxfB9VECIXPfe/CDkTHPcKgrxP80/AQJksRmWKBtFU3dRktYVscqUplz7
gS3EelAJ3NYscqWQevCXSvGsSpiNJfePKNLRrDSTKX+eKbAignHvcRhJ6YuP4QrY
t7ZGm7VZf+HSY/XYXbcXEO8zcaf3LFT1lO3KAQ3/nmFie/CuVCC+Dpl74OPsBvcD
+3uhQHqvm8AwnxBmTRtMNH3AtaDFPxT9hbebhsoJKujSb5+5aC4ygDAnY0E6QWfJ
wYG/qKz6+dtrFVIOZG3TFjz2/kgjXRd8zegYtxn20KH1Qk/i+JqaIofbwPvPWAKS
A5vi6sLt6AruRUh213E9+Pi+EWQs1Qhexqjk1rtna9RUkMmu2Qbx50hKkgdgE4Q7
EWcQSB43bpGRo5xt4zhy7fnBPj3zxjJK9gAzeGNrbN16z5gulHarpLWb9X5ujli4
9zv7wk00SQIaSqlVFKBM
=YW4N
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.14' of git://git.pengutronix.de/git/pza/linux into next/drivers
Pull "Reset controller changes for v4.14" from Philipp Zabel:
- constify zx2967 reset_ops
- add a convenience API to manage an array of resets
- let deassert report success and let assert report success for shared resets
if the reset controller driver does not implement (de)assert.
- add HSDKv1 reset driver
- remove Gemini reset controller, the driver is made obsolete
by a combined clock/reset driver in drivers/clk
- fix the total number of reset lines in the sunxi driver
- various uniphier updates and fixes:
- remove sLD3 SoC support
- simplify system reset register and bit definitions
- add audio systems, video input subsystem, and analog amplifiers reset
controls
* tag 'reset-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
reset: uniphier: add audio systems reset control
reset: sunxi: fix number of reset lines
reset: uniphier: do not use per-SoC macro for system reset block
reset: uniphier: remove sLD3 SoC support
Revert "reset: Add a Gemini reset controller"
ARC: reset: introduce HSDKv1 reset driver
reset: make (de)assert report success for self-deasserting reset drivers
reset: Add APIs to manage array of resets
reset: zx2967: constify zx2967_reset_ops.
* Add RZ/G1M (r8a7743) binding to apmu driver
This allows SMP to be supported on the RZ/G1M SoC
* Add bindings for iW-RainboW-G22D-SODIMM RZ/G1E SODIMM development kit
This is in preparation for adding DTS to support this hardware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZlWDoAAoJENfPZGlqN0++u+IP/097qIrO8k05/G4pulox3N+H
bRa8FF6UNQq5XIKy3I/jz19zNDo0FxnqF23kVaDzakrgS0A/B9cTL3k9XNEsPaty
1D5BOj4Dv53rpMJjXrVpaM54wRmdvVCk8VVHPwoduJgn9TTv6vOFa8TxN4L7aI6T
pu/RjKOVN4V31b+0dENs0Uz4u/AEcpTfrjuzrVseO2zBfLnJHSRUnxXhnuCUC6qd
db7xDVVvwhd6B0GuAzu2c0EBhXKO/C6epF5aqiGN0auZgeNcjT6EEOUpmhmQxFOm
9iURVNUtwUQPcqzHvJ4bJdLN0OltSIxiBySvd59YTu62v4gvBxfPS4HE1lx9B/F2
PWbQWX4s+38vB5qmZSznFDavVRYEUPdvjuk9OdkzhNyYyRVie010+qcqcdALB5rj
ehB/3V0J+yr+7RfwNECiWSqZZWACZHtCsMXz1VK/AE8P9Ltr7IinvgJ/+6aRGONa
BGOn5NTuTKh7fFrwJ64Pt8vcSjOHBXX4dMbQkENYQloYPjFY9ClkhMHsacG8kxdZ
27EXAZcFgSTLfWdbL6nzjRf5Np6JNn6CSSr7z/8Iw8KEPgj5D0MKSyVjHZPNyvbI
U+SDDnXt99nDcZSifWzf/U4Vfhoe+cybfc2umz4OkjOTI6Ep8jRdrsEEf+xy+wmN
40ipe1aPB1oyqKR1AG44
=uw/C
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Add RZ/G1M (r8a7743) binding to apmu driver
This allows SMP to be supported on the RZ/G1M SoC
* Add bindings for iW-RainboW-G22D-SODIMM RZ/G1E SODIMM development kit
This is in preparation for adding DTS to support this hardware
* tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: apmu: Document r8a7743 support
ARM: shmobile: document iW-RainboW-G22D SODIMM SOM Development Platform
ARM: shmobile: document iW-RainboW-G22M-SM SODIMM System on Module
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZloV7AAoJEFBXWFqHsHzOeIAH/ieM8fZEeUHO9waD4aoQJulp
kQHbJFKlEaQrB/y9LVUmNae0w/dpOaf5k/NVtfLQAZQhMqN6Y9XFQA0fnUAgiNbs
fknQpL6VnrO7nGUDEbIUommrRDPEVN9SEiiPpLpD938QjUDxTAibb8++QQOHC/S6
NLQbYMvubDTaUXkOiRodLQU6U/RQ5Byzmu+ytuKjlB1la0OzMegebD/OMXZtgysx
hcEDVBIEZmQO1TPrl5p6IZjjdHs1ua4gfRLQWq1RPXECakHJuyCPKILibyRID15j
w0C+sTxP1uIN950VYzufrbLIdyheWHSrx0FZSWa7tnus8W+h8kBAUd6NxyHLiyU=
=0Cwx
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.14" from Shawn Guo:
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
* tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-bx50v3: Enable i2c recovery mechanism
ARM: dts: imx6q-apalis-eval: add support for Apalis Evaluation Board
ARM: dts: imx6: add support for Toradex Ixora V1.1 carrier board
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: use i2c from dwc hdmi
ARM: dts: imx6q-apalis-ixora: add camera i2c bus definition
ARM: dts: imx6q-apalis-ixora: get rid of obsolete fusion comment
ARM: dts: imx6qdl-apalis: reword cam i2c comment
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: get rid of tegra legacy gen1_i2c comment
ARM: dts: imx6q-apalis-ixora: combine aliases
ARM: dts: imx6qdl-apalis: split usdhc1 pinctrl to support 4- and 8-bit
ARM: dts: imx6q-apalis-ixora: fix usdhc2 pinctrl property
ARM: dts: imx6ul-liteboard: Support poweroff
ARM: dts: imx: add CX9020 Embedded PC device tree
ARM: dts: imx53: add alternative UART2 configuration
ARM: dts: imx53: add srtc node
dt-bindings: arm: Add entry for Beckhoff CX9020
ARM: dts: i.MX25: add RNGB node to dtsi
ARM: dts: imx6ul-14x14-evk: Remove unrelated pin from ENET group
ARM: dts: imx7d-sdb: Add flexcan support
ARM: dts: imx7-colibri: add NAND support
...
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=WUr3
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-08-18
Here's one more bluetooth-next pull request for the 4.14 kernel:
- Multiple fixes for Broadcom controllers
- Fixes to the bluecard HCI driver
- New USB ID for Realtek RTL8723BE controller
- Fix static analyzer warning with kfree
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree bindings document for PWM on Rockchip rv1108 SoC.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
New PWM module provides two individual clocks for APB clock and function
clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Remove support for the SH7372 (SH-Mobile AP4) from the renesas-tpu
driver.
Commit edf4100906 ("ARM: shmobile: sh7372 dtsi: Remove Legacy
file") removed this SoC from the kernel in v4.1.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add interrupt-names property in DT - if future revisions of the IP
have different sets of interrupts the binding can adapt gracefully.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
CC: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The display engine on Allwinner A64 wants to claim the SRAM C section.
Add a SRAM controller compatible for A64, and a SRAM section compatible
for its SRAM C.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
add trivial device tree binding "devantech,srf02" and "devantech,srf10"
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Add binding document for serial bluetooth chips using
Broadcom protocol.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
there may use enable pin to control dmic start and stop,
so add this property in dt-bindings.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds dt-binding documentation for Mediatek MT2712.
Only include very basic items: cpu, gic and uart.
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update various properties to properly indicate their requirement depending
on the SoC.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Document APMU and SMP enable method for RZ/G1M
(also known as r8a7743) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document the iW-RainboW-G22D device tree bindings.
It is just a placeholder for the time being, the actual
implementation is not available yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document the iW-RainboW-G22M-SM SODIMM System on Module device tree
bindings. It is just a placeholder for the time being, the actual
implementation is not available yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car USB 2.0 controller can change the clock source from an oscillator
to an external clock via a register. So, this patch adds support
the clock source selector as a clock driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmET9EQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZbjCACKFO9Hp8Xwwg2nEM8DL3i+MlGaqxjIrcsb
WskuVOJjkAA4hMnrd7XvbpzJJusAquGqMd042ZCWtrNa1AwzCy0ZkYjDFNL27rXH
DqrHmJZowSoTHxlo8QKaevXH3ZZnp8TDz4IqaD0+UZx7DgZSOjR1a+feseh1Jn/V
9WBUJhNAFtKMiJBkTIpaDUk0E6OxIspdvlJurYmwUvDbfZKlpZrXHYKXSuUhFS9s
JX4Dqi5eF96Mctpi8GhaHGf7awPQf4oQBZfsXxhhS/efzX/v0HWqUPt40o2THi0F
ZbFFE3xAFaWisA+cbg8xnzJc8ZAwz2UmS6FgQ9lrqKyGN74buwgP
=spNi
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.14" from Heiko Stübner:
64bit Rockchip devicetree changes containing fixes for pinctrl typos
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
* tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: update dynamic-power-coefficient for rk3399
arm64: dts: rockchip: add rk3328 spdif node
arm64: dts: rockchip: add rk3368 spdif node
arm64: dts: rockchip: enable sdmmc controller on rk3399-firefly
arm64: dts: rockchip: Add rk3328 io-domain node
arm64: dts: rockchip: kill pcie_clkreqn and pcie_clkreqnb for rk3399
arm64: dts: rockchip: change clkreq mode for rk3399-firefly
arm64: dts: rockchip: enable the GPU for RK3399-GRU
arm64: dts: rockchip: add ARM Mali GPU node for RK3399 SoCs
dt-bindings: gpu: add the RK3399 mali for rockchip specifics
arm64: dts: rockchip: remove abused keep-power-in-suspend
arm64: dts: rockchip: remove num-slots from all platforms
arm64: dts: rockchip: change clkreq mode for rk3399-evb
arm64: dts: rockchip: add SdioAudio pd control for rk3399
arm64: dts: rockchip: enable usb2 for RK3328 evaluation board
arm64: dts: rockchip: add usb2 nodes for RK3328 SoCs
arm64: dts: rockchip: set rk3399 dynamic CPU power coefficients
arm64: dts: rockchip: Use vctrl regulators for dynamic CPU voltages on Gru/Kevin
arm64: dts: rockchip: Update CPU regulator voltage ranges for Gru
arm64: dts: rockchip: fix typo in mmc pinctrl
UAPI Changes:
- vc4: Allow userspace to dictate rendering order in submit_cl ioctl (Eric)
Cross-subsystem Changes:
- vboxvideo: One of Cihangir's patches applies to vboxvideo which is maintained
in staging
Core Changes:
- atomic_legacy_backoff is officially killed (Daniel)
- Extract drm_device.h (Daniel)
- Unregister drm device on unplug (Daniel)
- Rename deprecated drm_*_(un)?reference functions to drm_*_{get|put} (Cihangir)
Driver Changes:
- vc4: Error/destroy path cleanups, log level demotion, edid leak (Eric)
- various: Make various drm_*_funcs structs const (Bhumika)
- tinydrm: add support for LEGO MINDSTORMS EV3 LCD (David)
- various: Second half of .dumb_{map_offset|destroy} defaults set (Noralf)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Cihangir Akturk <cakturk@gmail.com>
Cc: David Lechner <david@lechnology.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
* tag 'drm-misc-next-2017-08-16' of git://anongit.freedesktop.org/git/drm-misc: (50 commits)
drm/gem-cma-helper: Remove drm_gem_cma_dumb_map_offset()
drm/virtio: Use the drm_driver.dumb_destroy default
drm/bochs: Use the drm_driver.dumb_destroy default
drm/mgag200: Use the drm_driver.dumb_destroy default
drm/exynos: Use .dumb_map_offset and .dumb_destroy defaults
drm/msm: Use the drm_driver.dumb_destroy default
drm/ast: Use the drm_driver.dumb_destroy default
drm/qxl: Use the drm_driver.dumb_destroy default
drm/udl: Use the drm_driver.dumb_destroy default
drm/cirrus: Use the drm_driver.dumb_destroy default
drm/tegra: Use .dumb_map_offset and .dumb_destroy defaults
drm/gma500: Use .dumb_map_offset and .dumb_destroy defaults
drm/mxsfb: Use .dumb_map_offset and .dumb_destroy defaults
drm/meson: Use .dumb_map_offset and .dumb_destroy defaults
drm/kirin: Use .dumb_map_offset and .dumb_destroy defaults
drm/vc4: Continue the switch to drm_*_put() helpers
drm/vc4: Fix leak of HDMI EDID
dma-buf: fix reservation_object_wait_timeout_rcu to wait correctly v2
dma-buf: add reservation_object_copy_fences (v2)
drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD
...
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlmTJfQRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXNA1A/+MLAg3q4K9IKWGTXbus9yBoKk8w2WFbSs
Yz/tzzOaNNhXdv3JdXh3f8O8wpID8LnxSblM001olks7Q9KSHMSyd0MUm4SgEQk2
hyFnEZU3e1eAe86LEDMTJNnKLLdCx3+RZHLvaRy3iHVIWBVZQmwD4l5daCt6iA0N
Yoy77MHkgJ0hnFrvcXr3e5+UzZR4g0JvS0T63sEQ5FbX6Uf4NTp67ubTYN3d/Zb9
E+GhPiNsOPeecVzDZR/C1eT7xasBf7qEl9qfJlglVPV8cVsZ6FUzsQb/aYixKaO2
fw1spQ3dpG9Scoi1AlU8AjapZXq8ocwS57L4kXRzlkm8ce6fj8a0aChX3jGKJMNx
RPdfjRRUOjvQt5Jg1VCh1J3Rr6xtQv05fkcowHfyVrhVxIa/mlnFv2qIb6N4u+Ra
nXIYTiBxxwHeiy/nwz+mjcvbOe12Jj9E7DAidrxxr/cpNeRbZMz9w5vI2rJ3sUbK
+DYWTVMhE0+TYZIFNPRM8tEyem/3omrpIQyM2K4IYk/E2b0aMF6UXlJP+i8dvL8o
01Ad2Gzr/Z9seD0YrhYJVM+LmR/qOn/10gKmtznOKM2trGxb4suq3mdSx/RMmneC
gGl0ltudVh0s1jWts/51H+BDYZ2J3DbJRDJAahIAkVEBfQCl6LRjyO4goi+SCaLq
z8out2VsHA0=
=zikX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omaps for v4.14 merge window" from Tony Lindgren:
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
* tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: nokia n900: update dts with camera support
ARM: dts: Add support for dra76-evm
ARM: dts: Add support for dra76x family of devices
ARM: dts: DRA7: Add pcie1 dt node for EP mode
ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
ARM: dts: dra7xx: Enable NAND dma prefetch by default
ARM: dts: am437xx: Enable NAND dma prefetch by default
ARM: dts: am335x-evm: Enable NAND dma prefetch by default
ARM: dts: omap4-droid4: Add vibrator
ARM: dts: motorola-cpcap-mapphone: set initial mode for vaudio
ARM: dts: omap3: Remove needless interrupt-parent property
ARM: dts: Disable HDMI CEC internal pull-ups
ARM: dts: am437x-gp-evm: Add support for buzzer
ARM: dts: Add dra7 iodelay configuration
ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"
ARM: dts: am572x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: am571x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
...
Add arm_global_timer node on Armada 38x
Fix PCI bus dtc warnings on mvebu 32 bits device tree files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmNhZUACgkQCwYYjhRyO9VwCACgpK2SLzw3pfmFMpaRZqPf7yqQ
eVoAmwf/qVDF+pPs8GIzyxyBJP7C27SR
=9oc8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.14 (part 1)" from Gregory CLEMENT:
Add arm_global_timer node on Armada 38x
Fix PCI bus dtc warnings on mvebu 32 bits device tree files
* tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: Add arm_global_timer node
ARM: dts: marvell: fix PCI bus dtc warnings
* Document R-Car D3 (r8a77995) SoC and Draak board
* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs
Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
piece of SRAM for the jump stub +for secondary CPU bringup and CPU
hotplug. +This memory is reserved by adding a child node to a
"mmio-sram" node..."
* Add a VSP channel index to DU vsps
Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
bindings don't support specifying that kind of SoC integration scheme.
Extend them with a VSP channel index."
* Add R-Car M3-W (r8a7796) HDMI TX DT bindings
This is compatible with existing R-Car H3 (r8a7795) support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnO5
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Document R-Car D3 (r8a77995) SoC and Draak board
* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs
Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
piece of SRAM for the jump stub +for secondary CPU bringup and CPU
hotplug. +This memory is reserved by adding a child node to a
"mmio-sram" node..."
* Add a VSP channel index to DU vsps
Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
bindings don't support specifying that kind of SoC integration scheme.
Extend them with a VSP channel index."
* Add R-Car M3-W (r8a7796) HDMI TX DT bindings
This is compatible with existing R-Car H3 (r8a7795) support
* tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Document Renesas Draak board DT bindings
ARM: shmobile: Document R-Car D3 SoC DT bindings
dt-bindings: display: rcar-du: Add a VSP channel index to the vsps DT property
dt-bindings: sram: Document renesas,smp-sram
dt-bindings: display: renesas: Add R-Car M3-W HDMI TX DT bindings
support for new dra762 SoC. The other changes are are for legacy
DMA code removal, and MMC quirk and iodelay config for dra7.
-----BEGIN PGP SIGNATURE-----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=FBGl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "soc changes for omaps for v4.14" from Tony Lindgren:
SoC updates for omaps for v4.14. Most of the chages are to add
support for new dra762 SoC. The other changes are are for legacy
DMA code removal, and MMC quirk and iodelay config for dra7.
* tag 'omap-for-v4.14/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: dra7: powerdomain data: Register SoC specific powerdomains
ARM: dra762: Enable SMP for dra762
ARM: dra7: hwmod: Register dra76x specific hwmod
ARM: dra762: Add support for device identification
ARM: OMAP2+: board-generic: add support for dra762 family
ARM: OMAP2+: Select PINCTRL_TI_IODELAY for SOC_DRA7XX
ARM: OMAP2+: Add pdata-quirks for MMC/SD on DRA74x EVM
ARM: OMAP2+: Remove unused legacy code for DMA
Add R-Car D3 (r8a77995) support to the Renesas-specific SoC drivers
- SoC identification
- System controller
- Reset controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AO//
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Pull "Renesas ARM Based SoC Drivers Updates for v4.14" from Simon Horman:
Add R-Car D3 (r8a77995) support to the Renesas-specific SoC drivers
- SoC identification
- System controller
- Reset controller
* tag 'renesas-drivers-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-rst: Add support for R-Car D3
soc: renesas: rcar-sysc: Add support for R-Car D3 power areas
soc: renesas: Add r8a77995 SYSC PM Domain Binding Definitions
soc: renesas: Identify R-Car D3
jtag/sdmmc switching for rk3328.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmEP/AQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf/lCACcJnVGr9PB9ibmTo7LASmljN+OP2G+9o3i
sOlxlkh5eM5sh9Tbg0NPVBziPmTYhBoPrFQjGEvt01m62gAOf7wugPRStKAivL7h
/pAUhkL1f4yIR0AnplLgy4+9wNJ7zK5DCj4dDCwd0+vX+aZbgDACPLdqn0afwuu2
g8pA3C5fRvThVjNpXzwHQSicUOmsvHPWpOWzx1YiKnXxXGKO0Xev+jDseWGqTMXR
8BXtb62G0QMHGgnrEu2TFex+SzdTumv9r4NpxP3+uytSQogbWUwCUAWpLxxxvgEJ
dAX9VcTaaJU3CMUwKot1mqmec0wElbwogx961An9bi4EoE+ru4Lt
=YgWd
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-drivers-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Pull "Rockchip driver changes for 4.14" from Heiko Stübner:
Powerdomain support for rk3366 and disabling of the automatic
jtag/sdmmc switching for rk3328.
* tag 'v4.14-rockchip-drivers-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: power-domain: add power domain support for rk3366
dt-bindings: add binding for rk3366 power domains
dt-bindings: power: add RK3366 SoCs header for power-domain
soc: rockchip: disable jtag switching for RK3328 Soc
The PCIe connector provide a optional 12V power supply for high power
downstream components, so we add this as an optional one if we need to
control it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.
Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Add a new compatible string for the RZ/G1E (R8A7745) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Integrate with the newly added USB charger interface to limit the current
we draw from the USB input based on the input device configuration
identified by the USB stack, allowing us to charge more quickly from high
current inputs without drawing more current than specified from others.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
add dt-binding document for MediaTek MT6380 PMIC
Signed-off-by: Chenglin Xu <chenglin.xu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Device Tree binding document for Broadcom USB Device
Controller (BDC).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
HPLL is in fact not the clock we need. Remove prescription of which clock to
avoid further error. Please refer to your datasheet and double check like I
should have.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add property "qcom,dtest-buffer" to specify which dtest rail to feed
when the pin is configured as a digital input.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZkNpUAAoJEHm+PkMAQRiGr68H/2nr8kxpoUhZ7eA5C71waCjh
gnJSevkzJAp+fCb0KfQFAp1qvpmLLle4e6tAxYgTQZg4Z3W5cJJNfxu9TzY5sGuL
o9QUr43XzABepW4e4jhRtZv6dj3K6XruNeDQKXDZTDcc/S8zoiS/Pltq7VgPcAuM
kX+3qsNdUyknngD6b0z9NtJkb0mHKY6J8MpraWRO34egDwsaN/tuhRj0DRQpCoyQ
x/k+hMbc9MB9Dn8cfACo6Omb+r5Rfd7dTBUAju/TnIIgs//9voHba307N7XvLJZg
kWc8MqMQQZXfRZHB0atpDMHyZS/XQRlNPXj76j0+Ud/byODKTFkkazmgTpALvj8=
=CxeU
-----END PGP SIGNATURE-----
Backmerge tag 'v4.13-rc5' into drm-next
Linux 4.13-rc5
There's a really nasty nouveau collision, hopefully someone can take a look
once I pushed this out.
dra76-evm is a board based on TI's dra76 processor targeting
for infotainment systems. Adding support for this platform.
dra76-evm and dra7-evm has a similar layout except with few differences.
So create a dra7-evm-common.dtsi with similarities on dra76-evm and
dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for Moxa UC-8100-ME-T open platform
The UC-8100-ME-T computing platform is designed
for embedded data acquisition industrial applications
The features of UC-8100-ME-T series are:
* eMMC
* SPI flash
* SD slot
* 2x LAN
* 2 RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with USB signal
* USB host
* EEPROM
* TPM
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fix unit adress as suggested by Rob]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a compatible string "brcm,bcm2836-smp" for Broadcom's
BCM2836 and BCM2837 to the 32 bit ARM CPU device tree binding.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
The spi on rv1108 is the same as other rockchip based
socs, add compatible string for it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
74HC595 has an /OE (output enable) pin that can be controlled by a GPIO.
Introduce an optional property called 'enable-gpios' that allows
controlling the /OE pin.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch adds keystone-k2g compatible, specific properties and
an example. The patch also adds the details of supported SoCs
for each compatible.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rapid General-Purpose Input and Output with 2 Ports (RGPIO2P)
on MX7ULP is similar to GPIO on Vibrid, except it has an extra
Port Data Direction Register (PDDR) used to configure the individual
port pins for input or output.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add fallback compatibility string for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Also deprecate renesas,gpio-rcar as its name is more generic than its
implementation.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cortina Gemini pin controller uses the standard pin control
bindings for muxing functions with groups so these bindings
should be entirely uncontroversial.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 3 IP blocks pin routes need to be switched, that are
emmc-cmd, spi, i2s. And there are some pins need to be recalced,
which are gpio2c4~gpio2c7 and gpio2d0.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed AST2500 SoC contains a number of USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller (x2)
* USB 2.0 Virtual Hub
* USB 2.0 Device Controller
* USB 1.1 HID Controller
The controllers are exposed via two USB ports with functionality muxed
as required. The following table illustrates the relationships between
the ports and the controllers via the mux function names:
Port | USB Version | USB Mode | Mux Function
------|--------------|--------------|-------------
A | 2.0 | Virtual Hub | USB2AD
A | 2.0 | Host | USB2AH
B | 1.1 | HID | USB11BHID
B | 2.0 | Device | USB2BD
B | 2.0 | Host | USB2BH
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2400 contains several USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller
* USB 2.0 Virtual Hub
* USB 1.1 HID Controller
Pins for three ports are routed to the three controllers such that:
* Port 1 is a dedicated USB 1.1 host port
* Port 2 is shared between the USB 1.1 host and HID controllers
* Port 3 is shared between the USB 2.0 host and Hub controllers
As the pins for port 1 are fixed function there is no associated mux
function or group described in the bindings. Ports 2 and 3 are muxed as
above, and the table below describes the mapping between pinmux function
names and ports:
Port | USB Version | USB Mode | Mux Function
------|--------------|-----------|-------------
1 | 1.1 | Host | -
2 | 1.1 | Host | USB11H2
2 | 1.1 | HID | USB11D1
3 | 2.0 | Host | USB2H1
3 | 2.0 | Device | USB2D1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i.MX 7ULP has three IOMUXC instances: IOMUXC0 for M4 ports,
IOMUXC1 for A7 ports and IOMUXC DDR for DDR interface.
This patch adds the IOMUXC1 support for A7.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the remaining pin functions and mux groups.
All unknown and debug functions are omitted. Existing functions
for qpic, sdio, rgmii, rmii, wifi/d are squashed together as
much as possible. And only in case of a clash, the individually
named functions have been kept. The exceptions are:
led0-11
i2s_rx, i2s_tx, i2s_td, i2s_spdif_in, i2s_spdif_out,
smart0-3
Cc: Varadarajan Narayanan <varada@codeaurora.org>
Cc: Ram Chandra Jangir <rjangir@codeaurora.org>
Cc: John Crispin <john@phrozen.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a reset line for analog signal amplifier core (ADAMV) on
UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
