We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma.
Fixes: d95adfd458 ("ARM: dts: am437x: Move l4 child devices to
probe them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the SPI NOR device used to boot up the system
to the iWave RZ/G1N Qseven System On Module DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The iWave RZ/G1N board is almost identical to RZ/G1M. cmt and rwdt modules
are SoC specific and should be part of board dts rather than SoM dtsi. By
moving these nodes to the common dtsi it allows cmt and rwdt to be enabled
on both of these boards with less lines of code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The current oversampling rate of 512 means that for 48 kHz 16 bit
stereo, the MCLK is running at the same rate as the module clock,
so there is no head room to support higher sampling rates. The codec
however supports up to 192 kHz for playback.
This patch drops the oversampling rate from 512 to 128, so that 192 kHz
audio can be played back directly without downsampling. Ideally we
should be using different oversampling rates for different sampling
rates, but that's not possible without a platform-specific machine
driver.
Fixes: 870f1bd1f5 ("ARM: dts: sun8i: Add audio codec, dai and card for A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like on the A33, the video engine on the H3 can map any address in
memory, so there is no particular need to have reserved memory at a fixed
address.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While we believed that the memory for the video engine had to be kept
in the first 256 MiBs of DRAM, this is no longer true starting with the
A33 and any address can be mapped.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike in previous generations, the system-control register range is not
limited to a size of 0x30 on the H3. In particular, the EMAC clock
configuration register (accessed through syscon) is at offset 0x30 in
that range.
Extend the register size to its full range (0x1000) as a result.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c7 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The values are taken from Amlogic's 3.10 kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The values are taken from Amlogic's 3.10 kernel sources. Their sources
have a "meson8m2_n200_2G.dtd" which defines a different voltage table:
- 0.86V for 96MHz
- (values in between omitted)
- 1.14V for 1.992GHz
The reason for this is simply the hardware design because the voltage
regulator on this board is has a minimum output of 0.86V and a maximum
output of 1.14V. The recommended settings are added with this patch
instead of using the values that are only valid for one board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8b SoC is using four Cortex-A5 cores. These come with an ARM
global timer.
This adds the Cortex-A5 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8B SoC is using four ARM Cortex-A5 cores which come with a
"TWD" (Timer-Watchdog) based timer. This adds support for the ARM TWD
Timer on this SoC.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoCs are using four Cortex-A9 cores. These come
with an ARM global timer.
This adds the Cortex-A9 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoC are using four ARM Cortex-A9 cores which
come with a "TWD" (Timer-Watchdog) based timer. This adds support for
the ARM TWD Timer on these two SoCs.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The public Meson8b (S805) datasheet describes a memory region called "A9
Periph base" which starts at 0xC4300000 and ends at 0xC430FFFF. Add a
simple-bus node and move all peripherals that are part of this memory
region.
This makes the .dts a bit easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Select CONFIG_TOUCHSCREEN_GOODIX so that we can have functional touch
screen by default on Digi International's AUO/Goodix LCD accessory kit used
with the ConnectCore 6UL SBC Pro (ccimx6ulsbcpro) board.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of passing GPIO numbers directly to the PalmLD
ATA driver, pass GPIO descriptors from the board file and
handle these in the driver.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While trying to use the dma_mmap_*() interface, it was noticed that this
interface returns strange values when passed an incorrect length.
If neither of the if() statements fire then the return value is
uninitialized. In the worst case it returns 0 which means the caller
will think the function succeeded.
Fixes: 1655cf8829 ("ARM: dma-mapping: Remove traces of NOMMU code")
Signed-off-by: Nathan Jones <nathanj439@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Chris has discovered and reported that v7_dma_inv_range() may corrupt
memory if address range is not aligned to cache line size.
Since the whole cache-v7m.S was lifted form cache-v7.S the same
observation applies to v7m_dma_inv_range(). So the fix just mirrors
what has been done for v7 with a little specific of M-class.
Cc: Chris Cole <chris@sageembedded.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch addresses possible memory corruption when
v7_dma_inv_range(start_address, end_address) address parameters are not
aligned to whole cache lines. This function issues "invalidate" cache
management operations to all cache lines from start_address (inclusive)
to end_address (exclusive). When start_address and/or end_address are
not aligned, the start and/or end cache lines are first issued "clean &
invalidate" operation. The assumption is this is done to ensure that any
dirty data addresses outside the address range (but part of the first or
last cache lines) are cleaned/flushed so that data is not lost, which
could happen if just an invalidate is issued.
The problem is that these first/last partial cache lines are issued
"clean & invalidate" and then "invalidate". This second "invalidate" is
not required and worse can cause "lost" writes to addresses outside the
address range but part of the cache line. If another component writes to
its part of the cache line between the "clean & invalidate" and
"invalidate" operations, the write can get lost. This fix is to remove
the extra "invalidate" operation when unaligned addressed are used.
A kernel module is available that has a stress test to reproduce the
issue and a unit test of the updated v7_dma_inv_range(). It can be
downloaded from
http://ftp.sageembedded.com/outgoing/linux/cache-test-20181107.tgz.
v7_dma_inv_range() is call by dmac_[un]map_area(addr, len, direction)
when the direction is DMA_FROM_DEVICE. One can (I believe) successfully
argue that DMA from a device to main memory should use buffers aligned
to cache line size, because the "clean & invalidate" might overwrite
data that the device just wrote using DMA. But if a driver does use
unaligned buffers, at least this fix will prevent memory corruption
outside the buffer.
Signed-off-by: Chris Cole <chris@sageembedded.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Switch over to using gpio leds now that we have the gpio driver for
the assabet board register in place.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add gpio keys support for the right-hand two buttons on the Assabet,
which can be used to wake up the CPU after PM.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Now that we have migrated all users of the legacy private SA1111 gpio
interfaces, we can remove these redundant GPIO interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As Lubbock now provides GPIOs via gpiolib for controlling the socket
power, we can use the MAX1600 driver. Switch Lubbock to use this
driver, which simplifies the code.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert mainstone to use the MAX1600 library and gpiod APIs for socket
status and control signals.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert Neponset to use the gpiod API to specify which GPIOs are used
for PCMCIA, and use the MAX1600 power switch library for Neponset,
simplifying the neponset pcmcia driver as a result.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert the low level PCMCIA driver to gpiod APIs for controlling
the socket power.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Simplify the code by getting rid of the conditional automatic
registration of the sa11x0 PCMCIA interfaces in sa1100_init(), and
require all platforms to explicitly call sa11x0_register_pcmcia().
Only one platform (iPAQ) is affected by this change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add a device node for the PCIe controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the xhci controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT node for the QSPI interface to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for the camera daughter board which is
connected to iWave's RZ/G1N Qseven carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add TPU support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for pwm[0123456] to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7744 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN[012] support to SoC dt.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CMT[01] support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch instantiates the thermal sensor module with thermal-zone
support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the r8a7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for can0 and can1 to the r8a7744 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G1N SoC (a.k.a. R8A7744).
This work is based on similar work done on the R8A7743 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb dmac and hsusb device nodes on RZ/G1N SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe internal PCI bridge devices, USB phy device and
link PCI USB devices to USB phy.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the SDHI0 controller on iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add eMMC support for iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add MMC node to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-5] and IIC[0,1,3] devices nodes to the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT node for the Advanced Power Management Unit (APMU), add the
second CPU core, and use "renesas,apmu" as "enable-method".
Also add cpu1 phandle node to the PMU interrupt-affinity property.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ethernet AVB support for R8A7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe GPIO blocks in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G1N (R8A7744) SoC. Added placeholders
to avoid compilation error with the common platform code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The thermal hardware description for the RZ/G1M SoC was added to its DTS
after the introduction of support for thermal zones, and included a
thermal-zones node from the beginning.
Hence there is no need to claim compatibility with
"renesas,rcar-thermal", which would be needed only for backwards
compatibility with kernels predating thermal zone support.
Fixes: 6c76b4f7d8 ("ARM: dts: r8a7743: Add thermal device to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lichee Pi Nano is a F1C100s board by Lichee Pi.
Add initial device tree for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
F1C100s is one product with the suniv die, which has a 32MiB co-packaged
DDR1 DRAM chip. As we have the support for suniv pin controller and CCU now, add a
initial DTSI for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds a set of DTS files that support all PXA3xx based Raumfeld
audio hardware devices.
Common nodes are factored out into 'common' and 'tuneable-clock' include
files to keep the top-level DTS files smaller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
[Robert: Reordered Makefile in alphabetical order]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
-----BEGIN PGP SIGNATURE-----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=zL87
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux into next/soc
This pull request contains Broadcom ARM-based SoCs machine files updates
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
* tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux:
ARM: mach-bcm: Switch bcm2835 and platsmp to SPDX identifier
ARM: BCM63XX: Enable reset controller support
ARM: brcmstb: Add entry for 7255
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
-----BEGIN PGP SIGNATURE-----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=iFMZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables drivers for STM32 timer, low power timer and analog hardware
that can be used on STM32MP1 SoC:
- Timer & LP Timer MFD core, PWM, trigger & encoder drivers
- IIO ADC/DAC/DFSDM
- vrefbuf regu driver (voltage reference buffer).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
There are more boards that can work with mmp2-dt than just Brownstone.
The OLPC XO-1.75 device tree root is compatible with "mrvl,mmp2" only.
The "mrvl,mmp2-brownstone" string is safe to remove: the Brownstone
device tree contains the "mrvl,mmp2" compatible string too.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.21, please pull the following:
- Rafal relicenses a bunch of DTS files he wrote under the GPL 2.0+/MIT
license and adds proper SPDX license tags in the process
- Rene adds support for the Linksys EA6500 v2 Wi-Fi router based on
BCM4708 plus two BCM4360 and BCM4331 radios
- Phil documents and updates the vchiq mailbox compatible string in
order to establish a correct agreement between the Raspberry Pi
firmware and the ARM CPU's view of what an ARM CPU cache line size is,
he also fixes the mailbox "reg" property to be correctly expressed in
bytes
- Stefan updates the Raspberry Pi Zero DTS files to use SPDX tags
- Florian enables the SATA PHY and AHCI controller on the BCM63138 SoCs,
he also does a bit of refactoring of aliases for the Northstar Plus
DTS files
-----BEGIN PGP SIGNATURE-----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=kE/p
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.21, please pull the following:
- Rafal relicenses a bunch of DTS files he wrote under the GPL 2.0+/MIT
license and adds proper SPDX license tags in the process
- Rene adds support for the Linksys EA6500 v2 Wi-Fi router based on
BCM4708 plus two BCM4360 and BCM4331 radios
- Phil documents and updates the vchiq mailbox compatible string in
order to establish a correct agreement between the Raspberry Pi
firmware and the ARM CPU's view of what an ARM CPU cache line size is,
he also fixes the mailbox "reg" property to be correctly expressed in
bytes
- Stefan updates the Raspberry Pi Zero DTS files to use SPDX tags
- Florian enables the SATA PHY and AHCI controller on the BCM63138 SoCs,
he also does a bit of refactoring of aliases for the Northstar Plus
DTS files
* tag 'arm-soc/for-4.21/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Describe Northstar pins mux controller
ARM: dts: BCM5301X: Add basic DT for Linksys EA6500 V2
ARM: dts: bcm2835-rpi-zero: Switch to SPDX identifier
ARM: dts: bcm283x: Correct mailbox register sizes
ARM: dts: bcm283x: Correct vchiq compatible string
dt-bindings: soc: Document "brcm,bcm2836-vchiq"
ARM: dts: NSP: Move aliases to bcm-nsp.dtsi
ARM: dts: BCM53573: Relicense SoC file to the GPL 2.0+ / MIT
ARM: dts: BCM63xx: Enable SATA AHCI and PHY for BCM963138DVT
ARM: dts: BCM63xx: enable SATA PHY and AHCI controller
ARM: dts: BCM53573: Relicense Tenda AC9 file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense BCM47094 file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense BCM47081/BCM4709 files to the GPL 2.0+ / MIT
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
cpu_is_mmp2() was equivalent to cpu_is_pj4(), wouldn't be correct for
multiplatform kernels. Fix it by also considering mmp_chip_id, as is
done for cpu_is_pxa168() and cpu_is_pxa910() above.
Moreover, it is only available with CONFIG_CPU_MMP2 and thus doesn't work
on DT-based MMP2 machines. Enable it on CONFIG_MACH_MMP2_DT too.
Note: CONFIG_CPU_MMP2 is only used for machines that use board files
instead of DT. It should perhaps be renamed. I'm not doing it now, because
I don't have a better idea.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.
Fixes: b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Mark as opp-suspend required devfreq Operating Performance Points to
fix resuming issues on Exynos 4 boards.
The patch is based on earlier work by Tobias Jakobi.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add option for Allwinner ARMv5 SoCs and SoC F1C100s (which has a die
used for many new F-series products, including F1C100A, F1C100s, F1C200s,
F1C500, F1C600).
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner also has some ARMv5 SoCs.
In order to add support for them, check ARM_MULTI_V7 before enabling
ARMv7 SoC's. Add help text for ARCH_SUNXI menuconfig.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial version of device tree file for Facebook Backpack CMM
(Chasis Management Module) ast2500 BMC.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 32MB mtd device.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The BMC can read the RTC battery voltage via ADC
channel 12.
Signed-off-by: Matt Spinler <spinler@linux.vnet.ibm.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add iio-hwmon-battery using adc channel 12 and enable adc to make
adc running. This channel is used to read RTC battery voltage.
Note with Romulus hardware design, it requires GPIOR3 to be pulled
high to read the voltage, otherwise the reading is 0.
When GPIOR3 is high, it consumes battery and impacts the battery life.
So it is left for user space to toggle the GPIO when trying to read the
voltage.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This allows userspace to switch away from bitbanging to use kernel
FSI with the coprocessor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This replaces the FSI compatible with the ColdFire FSI compatible.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored once
they figure out the underlying issue.
-----BEGIN PGP SIGNATURE-----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=m41T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored
once they figure out the underlying issue"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
MAINTAINERS: Remove unused Qualcomm SoC mailing list
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
ARM: dts: at91: sama5d2: use the divided clock for SMC
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
ARM: dts: rockchip: Remove @0 from the veyron memory node
arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
arm64: dts: sdm845-mtp: Reserve reserved gpios
arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
...
PXA25xx SoCs don't have a USB controller, so drop the node from the
common pxa2xx.dtsi base file. Both pxa27x and pxa3xx have a dedicated
node already anyway.
While at it, unify the names for the nodes across all pxa platforms.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Sergey Yanovich <ynvich@gmail.com>
Link: https://patchwork.kernel.org/patch/8375421/
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The clock controller node does not need a unit slave designator as it does
not have a reg property. Also, remove the underscore from the name.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
These are devices on the PXA bus, so make the device tree structure
reflect that.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The memory range for the hwuart is at 0x41600000, not 0x41100000.
This also solves a conflict with the MMC controller node.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The pinctrl node does not have any children, so the #address-cells and #size-cells
properties are not needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
PXA is single-core only, so this node will not have enumerable children.
Drop the #address-cells and #size-cells properties to squelch a dtc warning.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add a device node for hardware graphic acceleration.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
In commit 54a702f705 ("kbuild: mark $(targets) as .SECONDARY and
remove .PRECIOUS markers"), I missed one important feature of the
.SECONDARY target:
.SECONDARY with no prerequisites causes all targets to be
treated as secondary.
... which agrees with the policy of Kbuild.
Let's move it to scripts/Kbuild.include, with no prerequisites.
Note:
If an intermediate file is generated by $(call if_changed,...), you
still need to add it to "targets" so its .*.cmd file is included.
The arm/arm64 crypto files are generated by $(call cmd,shipped),
so they do not need to be added to "targets", but need to be added
to "clean-files" so "make clean" can properly clean them away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The dma remap code only makes sense for not cache coherent architectures
(or possibly the corner case of highmem CMA allocations) and currently
is only used by arm, arm64, csky and xtensa. Split it out into a
separate file with a separate Kconfig symbol, which gets the right
copyright notice given that this code was written by Laura Abbott
working for Code Aurora at that point.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Add node for s5p-jpeg codec, which is present in S5PV210 SoC.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We're finally changing omaps to use 8250_OMAP instead of SERIAL_OMAP
for multi_v7_defconfig. This will make things much easier for distros,
and the kernel already warns about the kernel console getting
redirected with CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP defaulting to y.
People using /etc/inittab still need to s/ttyO/ttyS/ if using the
out-of-box multi_v7_defconfig, and that did not seem to be an issue
when we moved omap2plus_defconfig to use 8250_OMAP earlier.
The other change is to enable CONFIG_SND_SOC_TLV320AIC23_I2C as a
loadable module that I forgot to send a pull request for earlier.
-----BEGIN PGP SIGNATURE-----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=rfKY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Defconfig changes for omaps for v4.21 merge window
We're finally changing omaps to use 8250_OMAP instead of SERIAL_OMAP
for multi_v7_defconfig. This will make things much easier for distros,
and the kernel already warns about the kernel console getting
redirected with CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP defaulting to y.
People using /etc/inittab still need to s/ttyO/ttyS/ if using the
out-of-box multi_v7_defconfig, and that did not seem to be an issue
when we moved omap2plus_defconfig to use 8250_OMAP earlier.
The other change is to enable CONFIG_SND_SOC_TLV320AIC23_I2C as a
loadable module that I forgot to send a pull request for earlier.
* tag 'omap-for-v4.21/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: multi_v7_defconfig: Enable 8250-omap serial driver and use it by default
ARM: omap2plus_defconfig: Add tlv320aic23 as module
Signed-off-by: Olof Johansson <olof@lixom.net>
Few more non-critical section annotation fixes for Clang and
remove obsolete timer header inclusion.
-----BEGIN PGP SIGNATURE-----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=rtgC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.21 merge window
Few more non-critical section annotation fixes for Clang and
remove obsolete timer header inclusion.
* tag 'omap-for-v4.21/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: timer: Remove obsolete inclusion of <asm/smp_twd.h>
ARM: OMAP2+: prm44xx: Fix section annotation on omap44xx_prm_enable_io_wakeup
ARM: OMAP2+: hwmod: Fix some section annotations
Signed-off-by: Olof Johansson <olof@lixom.net>
This activates the new PL11x DRM driver with the
Versatile Express family of reference designs.
-----BEGIN PGP SIGNATURE-----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=3sxh
-----END PGP SIGNATURE-----
Merge tag 'vexpress-defconfig-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/defconfig
Versatile Express defconfig updates:
This activates the new PL11x DRM driver with the
Versatile Express family of reference designs.
* tag 'vexpress-defconfig-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: defconfig: Enable the PL111 DRM driver on vexpress
ARM: defconfig: Update the vexpress defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
This is to replace the USB PHY initialization code (pxa_usb_phy_init(),
pxa_usb_phy_deinit()) with a proper PHY driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
The device-tree booted MMP2 needs to enable the timer clock, otherwise
it would stop ticking when the boot finishes.
It can also use the clock rate from the clk, the non-DT boards need to
keep using the hardcoded rates.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
The timer shall enable its clock.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Split Kconfig options for debug UART on Cyclone5
- Remove unused functions from socfpga platform code
- Turn on ARM and PL310 errata for SOCFPGA ARMv7 platform
-----BEGIN PGP SIGNATURE-----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=0ypv
-----END PGP SIGNATURE-----
Merge tag 'socfpga_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/soc
SoCFPGA updates for v5.0
- Split Kconfig options for debug UART on Cyclone5
- Remove unused functions from socfpga platform code
- Turn on ARM and PL310 errata for SOCFPGA ARMv7 platform
* tag 'socfpga_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: Turn on ARM errata for L2 cache
ARM: socfpga: Clean unused functions
ARM: debug: enable UART1 for socfpga Cyclone5
Signed-off-by: Olof Johansson <olof@lixom.net>
The base aspeed-g5.dtsi already defines a '/memory@80000000' node, so
'/memory' in the board files create a duplicate node. We're probably
getting lucky that the bootloader fixes up the memory node that the
kernel ends up using. Add the unit-address so it's merged with the base
node.
Found with DT json-schema checks.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- support more timers on meson8
- add the stdout-path property on several boards
-----BEGIN PGP SIGNATURE-----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=9yK+
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT updates for v4.21
- support more timers on meson8
- add the stdout-path property on several boards
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: add the clock inputs for the Meson timer
ARM: dts: meson: add the TIMER B/C/D interrupts
ARM: dts: meson: consistently disable pin bias
ARM: dts: meson8b: mxq: add the /chosen/stdout-path property
ARM: dts: meson8: minix-neo-x8: add the /chosen/stdout-path property
ARM: dts: meson6: atv1200: add the /chosen/stdout-path property
dt-bindings: timer: meson6_timer: document the clock inputs
dt-bindings: timer: meson6_timer: document all interrupts
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes mostly configure pinctrl for am437x-gp-evm. There is
also non-critical fix for a comment for Clang, and we enable earlycon
for am3517-evm.
-----BEGIN PGP SIGNATURE-----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=/+sU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.21 merge window
These changes mostly configure pinctrl for am437x-gp-evm. There is
also non-critical fix for a comment for Clang, and we enable earlycon
for am3517-evm.
* tag 'omap-for-v4.21/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-gp-evm: Add sleep state for beeper pins
ARM: dts: am437x-gp-evm: Add pinmux for gpio0 wake
ARM: dts: am437x-gp-evm: Add uart0 pinctrl default and sleep states
ARM: dts: am437x-gp-evm: Add pinctrl for debugss pins
ARM: dts: am437x-gp-evm: Add pinctrl for unused_pins
ARM: dts: am437x-gp-evm: Add state for ddr3 vtt toggle pin
ARM: dts: am3517-evm: Enable earlycon stdout path
ARM: dts: omap3-gta04: Fix comment block
Signed-off-by: Olof Johansson <olof@lixom.net>
This updates the Versatile Express family DTS files to
contain the correct and detailed information required
for the PL11x DRM driver to work properly.
-----BEGIN PGP SIGNATURE-----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=4oHX
-----END PGP SIGNATURE-----
Merge tag 'vexpress-drm-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Versatile Express DTS update for DRM:
This updates the Versatile Express family DTS files to
contain the correct and detailed information required
for the PL11x DRM driver to work properly.
* tag 'vexpress-drm-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Modernize the Vexpress PL111 integration
Signed-off-by: Olof Johansson <olof@lixom.net>
Despite Marvel keeps their base addresses secret there's a good chance
they're actually correct.
SSP1 and SSP3 bases were taken from OLPC 1.75: OpenFirmware and kernel
respectively. SSP2 and SSP4 addresses are from James Cameron who actually
has a copy of the data sheet.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
The USB OTG PHY chip. To be used by the OTG controller.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
I've gotten the base addresses, clocks and interrupts from an rusty and old
out-of-tree driver. I haven't actually checked against the datasheet, since
that one is reserved for the Marvell inner circle.
Tested with an accelerometer on TWSI6 on an OLPC XO 1.75 machine.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's apparently four of them on a MMP2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
The timer needs the timer clock to be enabled, otherwise it stops
ticking.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will be useful for boards that actually use GPIO pins.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
gpio-pxa uses two cell to encode the interrupt source: the pin number
and the trigger type. Adjust the device node accordingly.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Use SPDX license identifier for all SoCFPGA DTS files.
- Remove dma-mask property as it has been deprecated.
- Use tabs in DTS files.
- Use the specific "altr,stratix10-rst-mgr" property for the Stratix10
reset manager.
-----BEGIN PGP SIGNATURE-----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=IDQS
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v5.0
- Use SPDX license identifier for all SoCFPGA DTS files.
- Remove dma-mask property as it has been deprecated.
- Use tabs in DTS files.
- Use the specific "altr,stratix10-rst-mgr" property for the Stratix10
reset manager.
* tag 'socfpga_dts_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: use "altr,stratix10-rst-mgr" binding
ARM: dts: socfpga: use tabs for indentation
arm: dts: socfpga: remove dma-mask property
arm: dts: socfpga*.dts*: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
regulator name and referencing all cpus in the cooling maps instead
of only cpu0.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlv2mkYQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf2ZCACoJZ1G4trbzqhdH1DXlLac7hsk+Hu/1jTW
WrP6mXVyOJLdo3XRAoYEKI8WFx88pyXUDuXnxH4vO2SaoEDyIDYGuYxiiDZsrMiv
oX0uyx9JKpY3cSBiDsPkfaxdcyGmVP2x10gxJvcoF4mP3FlMh5Ovtoyq83djxm7B
/kw0NniMU9qKn8ilPAy+kiNADQkC3swupq0uLpt4wgvIPKkiGWEEaJjG30boc21q
qpFlB9PowM52ZIqttTjvzh/wnb0eB6sEcI9tuuUa4S8y0PHzRpiIco0pqUsuq6I4
UbAbqshORINRkJTZwhfw4HWmrKLF5s6vXGKFbx9M3TgVHKWGYHTw
=zDNA
-----END PGP SIGNATURE-----
Merge tag 'v4.21-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Powerdomain and QoS nodes for rk3066 and rk3188. A fix for a rock2
regulator name and referencing all cpus in the cooling maps instead
of only cpu0.
* tag 'v4.21-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add all CPUs in cooling maps
ARM: dts: rockchip: Fix rk3288-rock2 vcc_flash name
ARM: dts: rockchip: add rk3066/rk3188 power-domains
ARM: dts: rockchip: add qos nodes found on rk3066 and rk3188
dt-bindings: add power-domain header for RK3066 SoCs
dt-bindings: add power-domain header for RK3188 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
- Reomve non-existing EEPROM device from imx51-zii-rdu1 board.
It was added by mistake.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcAVNxAAoJEFBXWFqHsHzO0SYH/06mGVqrvAdCYYMamrcLPkom
7aVizSIcK6O+9ddxhA5pDSHMIKu0Wjn6d1acySeql6AWg0d9pECydoI7Rgfj/fDC
mw/aXlv9TJv+4R6/2MI/CEO2Xfi0c2d0nCzTAmsL3CKp92hIVqPTxc7mW5K9J8bx
W2wbj1wueCn/cLiynDV25krxq4BRbsU8g0Ke+HiuO89W9Qb87qgPyJjWeecyH/dl
/llXuiFzZqHYpmzdYacnKvKResVCCc8Ev4VgEF89M1M9tgOojQOakFfMBfTDEIHG
iooQLc6WLdYjsqDhmnUEbonZ+pHBbNPUvV0iHmR/9y0SyVZdrGgNWjVRSkKuT6I=
=OlmI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.20, round 2:
- Reomve non-existing EEPROM device from imx51-zii-rdu1 board.
It was added by mistake.
* tag 'imx-fixes-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of fixes contains minor regression fixes for LogicPD dts files
for MMC pinctrl and interrupts. There is also one section annotation fix
that shows up with Clang, and a fix for an unitialized field for omap1.
-----BEGIN PGP SIGNATURE-----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=EaEX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few minor fixes for omaps for v4.20-rc cycle
This set of fixes contains minor regression fixes for LogicPD dts files
for MMC pinctrl and interrupts. There is also one section annotation fix
that shows up with Clang, and a fix for an unitialized field for omap1.
* tag 'omap-for-v4.20/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: ams-delta: Fix possible use of uninitialized field
ARM: dts: am3517-som: Fix WL127x Wifi interrupt
ARM: dts: logicpd-somlv: Fix interrupt on mmc3_dat1
ARM: dts: LogicPD Torpedo: Fix mmc3_dat1 interrupt
ARM: dts: am3517: Fix pinmuxing for CD on MMC1
ARM: OMAP2+: prm44xx: Fix section annotation on omap44xx_prm_enable_io_wakeup
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of changes is needed to fix the broken GPIO support
for DaVinci boards in legacy mode after certain changes made to the
GPIO driver in 4.19, namely: commits 587f7a694f ("gpio: davinci: Use
dev name for label and automatic base selection") and eb3744a2dd
("gpio: davinci: Do not assume continuous IRQ numbering").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tCLo
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
DaVinci: fix GPIO breakage after v4.19
This set of changes is needed to fix the broken GPIO support
for DaVinci boards in legacy mode after certain changes made to the
GPIO driver in 4.19, namely: commits 587f7a694f ("gpio: davinci: Use
dev name for label and automatic base selection") and eb3744a2dd
("gpio: davinci: Do not assume continuous IRQ numbering").
* tag 'davinci-fixes-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
Signed-off-by: Olof Johansson <olof@lixom.net>
firmware on these devices as issues identifying the formally correct
node.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlv2krMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgenqB/4z/gAlUZ8xo9au7cHLXOKmg7WkhqRkWHsr
F1rib1I8wv2d6X+PkQv6QiejaJcp+Tj4unx6IGx904PADlCRj38uo+7jEgirf3h+
MGUcZM9+A1V1IvN31eaSTax9KO/XUaABxCBiDSH91YM6JZHRTh1oskjC1lt2pmfF
yygoVfX0jA6GC9+S1YpKAmMyY37ZFIyiZFak5qVPzDDIHKqRLgFDDc2gGTlsqTca
glxbHapRHXg624wUcuGgnRmhhrzNPFzrQ89/LAZX9MBAwC8p2SekhzE7VR2nAvvZ
9Asl7SU2lOjYTpWP/b8jONpPIPvDSXKnfYxQSYDD+Eud+kUk+rqU
=wPsf
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Moving the veyron memory node from memory@0 back to memory, as the
firmware on these devices as issues identifying the formally correct
node.
* tag 'v4.20-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Remove @0 from the veyron memory node
Signed-off-by: Olof Johansson <olof@lixom.net>
Single patch to use updated coresight graph bindings thereby removing
loads of dtc warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8TMG
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress updates for v4.20
Single patch to use updated coresight graph bindings thereby removing
loads of dtc warnings
* tag 'vexpress-updates-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress/TC2: Update entries to match latest coresight bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
This describes hardware & will allow referencing pin functions. The
first usage is UART1 which allows supporting devices using it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It is wireless home router based on BCM4708A0 with BCM4360 + BCM4331
wireless chipsets. The BCM4331 5GHz chip currently isn't supported only
due to missing compatible firmware.
Signed-off-by: Rene Kjellerup <rk.katana.steel@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The pm-rmobile driver is really a driver for the System Controller
(SYSC) found in R-Mobile SoCs. An equivalent driver for R-Car SoCs is
already located under drivers/soc/renesas/.
Hence move the pm-rmobile driver from arch/arm/mach-shmobile/ to
drivers/soc/renesas/, and rename it to rmobile-sysc.
Enable compile-testing on non-ARM and non-R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 59b89af1d5 ("ARM: shmobile: sh7372: Remove Legacy C
SoC code") removed the last user of the rmobile_pm_domain.resume()
callback.
Commit 44d88c754e ("ARM: shmobile: Remove legacy SoC code
for R-Mobile A1") removed the last user of the rmobile_pm_domain.no_debug
flag and of the "pm-rmobile.h" header file (outside the actual driver).
Hence remove no longer used rmobile_pm_domain members, and absorb the
header file into the driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure omap1_spi100k only on OMAP7xx. This allows running multiboard
kernels on non-OMAP7xx HW with CONFIG_SPI_OMAP_100K enabled.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently we get extra newlines on OMAP1/2 when the SoC name is printed:
[ 0.000000] OMAP1510
[ 0.000000] revision 2 handled as 15xx id: bc058c9b93111a16
[ 0.000000] OMAP2420
[ 0.000000]
Fix by using pr_cont.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
That symbol is not used outside the board file, there is no need to
keep it in the board header.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Those bitmap symbols defining pins of latch2 register, used with
read()/write() calls before the latch was converted to a GPIO device,
have been obsoleted by integer symbols defined inside the board file.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As all users of the board specific GPIO pins have been converted from
legacy integer-based to descriptor-based interface, there is no longer
a need to maintain statically assigned GPIO pin numbers. Drop support
for that.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Global GPIO numbers no longer have to be passed to leds-gpio driver,
replace their assignment with a lookup table.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now as the board header file is no longer included by drivers, move it
to the root directory of mach-omap1.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hwmod parses the DT hierarchically from root to search for matching
ti,hwmod property. With the introduction of L4 data, we have two nodes
with the ti,hwmod = "gmac" declaration, and the hwmod core only matches
the first one found, which is the target-module one. This node incorrectly
dropped the ti,no-idle flag, which causes number of problems, like ignoring
errata i877, and also causing an intermittent boot failure on certain dra7
boards.
Fix the issue by moving the ti,no-idle flag to the proper node.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this McASP FIFO would constantly underflow. EDMA
test via dmatest works though.
Let's revert the change for now until we know the root cause.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Video Image Compositor can be used to perform a variety of image
operations. Add a device tree node for it, so that it can be exposed
as a host1x channel to userspace.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This updates the Versatile defconfig to use the new P111 DRM
driver that is merged in the DRM subsystem.
We deactivate the old CLCD driver and activate the Pl111 DRM
driver and the SiI9022 HDMI bridge.
We activate DMA memory allocation using CMA so that the special
graphics memory for the on-board CLCD can be used.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the Versatile Express defconfig to match the
Kconfig changes in the kernel.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile Express was submitted with the actual display
bridges unconnected (but defined in the device tree) and
mock "panels" encoded in the device tree node of the PL111
controller.
This doesn't even remotely describe the actual Versatile
Express hardware. Exploit the SiI9022 bridge by connecting
the PL111 pads to it, making it use EDID or fallback values
to drive the monitor.
The also has to use the reserved memory through the
CMA pool rather than by open coding a memory region and
remapping it explicitly in the driver. To achieve this,
a reserved-memory node must exist in the root of the
device tree, so we need to pull that out of the
motherboard .dtsi include files, and push it into each
top-level device tree instead.
We do the same manouver for all the Versatile Express
boards, taking into account the different location of the
video RAM depending on which chip select is used on
each platform.
This plays nicely with the new PL111 DRM driver and
follows the standard ways of assigning bridges and
memory pools for graphics.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Meson Timer IP block has two clock inputs:
- clk81 for using the system clock as timebase
- xtal for a timebase with 1us, 10us, 100us and 1ms resolution
The clocksource driver does not use these yet, but it's still a good
idea to add them as this describes how the hardware actually works
internally.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The timer on Meson6/Meson8/Meson8b SoCs has four internal timer events.
For each of these a separate interrupt exists.
Pass these interrupts to allow using the timers other than TIMER A.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch removes support for the APQ8064 based Arrow SD600 eval
board. This board was never sold publicly and had very limited
distribution. As such, we are removing this board and no longer
going to support it.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
As per upstream discussion [1], we should have an SoC-specific
compatible string for Qualcomm's SDHCI nodes. Let's add it.
[1] https://lkml.kernel.org/r/20181105203657.GA32282@bogus
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch correctly sets the gpios property for the ak8963
magnetometer's DRDY pin so that interrupts work properly.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In two of the gen5 socfpga devicetree files, there are some lines
indented using spaces instead of tabs.
Fix this by correctly indenting them with tabs.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Follow the recent trend for the license description.
This is also in an effort to fully sync the devicetrees with U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Turn on these ARM and PL310 errata for SoCFPGA:
ARM_ERRATA_754322
ARM_ERRATA_764369
ARM_ERRATA_775420
PL310_ERRATA_588369
PL310_ERRATA_727915
PL310_ERRATA_753970
PL310_ERRATA_769419
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
These functions are unused externally, removed them and declare
the one used locally as static.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Cyclone5 and Arria10 doesn't have the same memory map for UART1.
Split the SOCFPGA_UART1 into 2 options to allow debugging on UART1 for Cyclone5.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The MMC0 controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The i2c nodes were pre-populated to ease the use of overlays. However, now
that we provide default muxing options for those nodes, the one in the DTS
don't provide any content at all.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Now that all the SoCs using the tablet reference design DTSI are using the
same pinctrl naming scheme, we can move back the pinctrl phandles to the
main DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pin groups are supposed to be in alphabetical order, and they aren't.
Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
DTC will emit a warning on our OPPs nodes for the common DTSI between the
A23 and A33 since those nodes use the frequency as unit addresses, but
don't have a matching reg property.
Fix this by moving the frequency to the node name instead.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The SOM204-EVB doesn't use the CTS pin, and thus was defining its own
pinctrl node for the UART3 muxing. Since we split away the TX and RX pin,
we can use the global node now, and only have the RTS pin in our local
node.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some UART nodes on the A20 DTSI do not share the same pattern that we use
everywhere else, with the RTS and CTS pins split away from the TX and RX
pins. Make those pin groups consistent with the rest of our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some gpio-keys definitions in our DTs were having buttons defined with a
unit-address and that would generate a DTC warning.
Change the buttons node names to remove the warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our I2C GPIO bus node name has a unit address, but no reg property, which
generates a warning in DTC. Change the name to remove that unit address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C's, MMC0 and MMC1 controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
There's no phandle pointing to the CMA pool, so it's label is unnecessary.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CMA node has a unit address, but no reg property which generates a
warning in DTC. Change the node name to reflect its usage and drop the unit
address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Harmless mistake, but it's incorrect. The DT spec provides recommendations
for the node names:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model. If appropriate, the
name should be one of the following choices:
...
interrupt-controller"
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit adds QSPI flash support to the iwg23s board specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add QSPI[01] support to the RZ/G1C SoC specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables cmt0 support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CMT[01] support to r8a77470 SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB DMAC nodes.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables watchdog support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds watchdog support to the r8a77470 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
[simon: moved node to preserve sort order]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the R-Mobile A1 (r8a7740), Emma Mobile EV2 (emev2) and
SH-Mobile AG5 (sh72a0) DTSI to include product name.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[simon: squashed similar patches]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LVDS0 encoder on Koelsh and Porter, and the LVDS1 encoder on Lager,
are enabled in DT but have no device connected to their output. This
result in spurious messages being printed to the kernel log such as
rcar-du feb00000.display: no connector for encoder /soc/lvds@feb90000, skipping
Fix it by disabling the encoders.
Fixes: 15a1ff30d8 ("ARM: dts: r8a7790: Convert to new LVDS DT bindings")
Fixes: e5c3f4707f ("ARM: dts: r8a7791: Convert to new LVDS DT bindings")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add uSD card and eMMC support to the iwg23s single board
computer powered by the RZ/G1C SoC (a.k.a. r8a77470).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Althought interface SDHI1 found on the RZ/G1C SoC (a.k.a.
r8a77470) is compatible with the R-Car Gen3 ones, its OF
compatibility is restricted to the SoC specific compatible
string to avoid confusion, as from a more generic perspective
the RZ/G1C is sharing the most similarities with the R-Car
Gen2 family of SoCs, and there is a combination of R-Car
Gen2 compatible SDHI IPs and R-Car Gen3 compatible SDHI IP
on this specific chip.
This patch adds the SoC specific part of SDHI1 support, and
since SDHI1 comes with internal DMA, its DT node looks fairly
different from SDHI0 and SDHI2.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
RZ/G1C comes with two different types of IP for the SDHI
interfaces, SDHI0 and SDHI2 share the same IP type, and
such an IP is also compatible with the one found in R-Car
Gen2. SDHI1 IP on the other hand is compatible with R-Car
Gen3 with internal DMA.
This patch completes the SDHI support of the R-Car Gen2
compatible IPs, including fixing the max-frequency
definition of SDHI2, as it turns out there is a bug in
Section 1.3.9 of the RZ/G1C Hardware User's Manual (Rev.
1.00 Oct. 2017).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree nodes for the I2C[0123] controllers. Also, add
the aliases node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This provides a pinctrl driver for the Renesas R9A06G032 SoC
Based on a patch originally written by Michel Pollet at Renesas.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The interrupt-parent property is set in sun5i.dtsi, so there's no need to
repeat it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our HDMI output endpoint on the A10 DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Fix the 'unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property' DTC warning for the gpio-keys DT node on A10 boards.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This is very helpful debugging USB issues.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andreas Müller <schnitzeltony@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is necessary to support network over bluetooth:
| Sep 11 15:36:33 imx6qdl-variscite-som bluetoothd[281]: kernel lacks bnep-protocol support
| Sep 11 15:36:33 imx6qdl-variscite-som bluetoothd[281]: System does not support network plugin
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andreas Müller <schnitzeltony@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CONFIG_ARM_UNWIND is removed when running 'savedefconfig', but
selected by ARM EABI (AEBI) support. This is done in preparation to making
further changes to this defconfig cleaner.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All recent emtrion modules based on i.mx6 make use of the DA9063.
Therefore enable it with the following defaults:
- CONFIG_MFD_DA9063=y
- CONFIG_REGULATOR_DA9063=y
- CONFIG_DA9063_WATCHDOG=m
MFD and REGULATOR are built-in to have it at Kernel boot-time.
The WATCHDOG is optional and could be loaded from userspace.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function_graph_enter() function does the work of calling the function
graph hook function and the management of the shadow stack, simplifying the
work done in the architecture dependent prepare_ftrace_return().
Have ARM use the new code, and remove the shadow stack management as well as
having to set up the trace structure.
This is needed to prepare for a fix of a design bug on how the curr_ret_stack
is used.
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@kernel.org
Fixes: 03274a3ffb ("tracing/fgraph: Adjust fgraph depth before calling trace return callback")
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
firmware and VCHI driver to coordinate on using the correct cache line
size for the platform.
-----BEGIN PGP SIGNATURE-----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=BEZr
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zY4r
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2018-11-27' into devicetree/next
This pull request adds a compatible string to the DT necessary for the
firmware and VCHI driver to coordinate on using the correct cache line
size for the platform.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The H3 and H5 features the same CSI controller that was initially found on
the A31.
Add a DT node for it.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
cpu0-supply in cpu0 is deprecated, instead each cpu-core is supposed to
list its supply separately. With the added cpu core phandles, update
existing rk3188 boards accordingly.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The fact that OPPs specified only on cpu0 work is Linux specific and
normally cpu frequencies should be specified for each cpu core.
To facilitate this without needing to duplicate the frequency table
each time, convert to opp-v2 before adding references to all cores.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The Rockchip i2s always just requires a sound-dail-cells value of 0,
so add them to the core soc dtsi for convenience.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The lradc's analog reference voltage is set to 3.0 volt in the
hardware. This is more or less set in copper for at least lradc0. Set the
property in the dts to ensure the lradc is referenced properly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the GPIO support on DaVinci boards
in legacy mode by allowing gpiolib to set the GPIO base automatically.
DaVinci board files use the legacy GPIO API with hard-coded GPIO line
numbers. Use the new fields in struct davinci_gpio_platform_data to
manually set the GPIO base to 0.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the GPIO support on DaVinci boards
in legacy mode by allowing gpiolib to set the GPIO base automatically.
DaVinci board files use the legacy GPIO API with hard-coded GPIO line
numbers. Use the new fields in struct davinci_gpio_platform_data to
manually set the GPIO base to 0.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the GPIO support on DaVinci boards
in legacy mode by allowing gpiolib to set the GPIO base automatically.
DaVinci board files use the legacy GPIO API with hard-coded GPIO line
numbers. Use the new fields in struct davinci_gpio_platform_data to
manually set the GPIO base to 0.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Pass the 'dmas' property to the UART ports so that DMA can
be supported.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It is not correct to assign the 24MHz clock oscillator to the GPIO
ports.
Fix it by assigning the proper GPIO clocks instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the Rockchip vendor tree the PMU interrupt number is
76, so fix it accordingly.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ARC, ARM, ARM64 and Unicore32 are all capable of parsing the "initrd="
command line parameter to allow specifying the physical address and size
of an initrd. Move that parsing into init/do_mounts_initrd.c such that
we no longer duplicate that logic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that we have central and global variables holding the physical
address and size of the initrd, we can have
early_init_dt_check_for_initrd() populate
phys_initrd_start/phys_initrd_size for us.
This allows us to remove a chunk of code from arch/arm/mm/init.c
introduced with commit 65939301ac ("arm: set initrd_start/initrd_end
for fdt scan").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Make phys_initrd_start and phys_initrd_size global variables declared in
init/do_mounts_initrd.c such that we can later have generic code in
drivers/of/fdt.c populate those variables for us.
This requires both the ARM and unicore32 implementations to be properly
guarded against CONFIG_BLK_DEV_INITRD, and also initialize the variables
to the expected default values (unicore32).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the GPIO support on DaVinci boards
in legacy mode by allowing gpiolib to set the GPIO base automatically.
DaVinci board files use the legacy GPIO API with hard-coded GPIO line
numbers. Use the new fields in struct davinci_gpio_platform_data to
manually set the GPIO base to 0.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the GPIO support on DaVinci boards
in legacy mode by allowing gpiolib to set the GPIO base automatically.
DaVinci board files use the legacy GPIO API with hard-coded GPIO line
numbers. Use the new fields in struct davinci_gpio_platform_data to
manually set the GPIO base to 0.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the network support in legacy boot
mode for da850-evm since we can no longer request the MDIO clock GPIO.
We now have the option to specify the GPIO base manually for davinci,
so add the relevant fields to platform data.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit eb3744a2dd ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit eb3744a2dd ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit eb3744a2dd ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit eb3744a2dd ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit eb3744a2dd ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since firmware does not initialize any of the generic timer CPU
registers pass the 'arm,cpu-registers-not-fw-configured' property as
suggested in Documentation/devicetree/bindings/timer/arm,arch_timer.txt.
This also aligns with other Rockchip SoC dtsi files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Like it is done on cpu nodes of other Rockchip SoCs, pass the
'clock-latency' property to the CPU node, so that cpufreq driver
can take the latency into account when switching frequencies.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the pin settings for the emmc pins so they can be used across multiple
boards.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let architectures opt into EISA support by selecting HAVE_EISA and
handle everything else in drivers/eisa.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is nothing architecture specific in the PCMCIA core, so allow
building it everywhere. The actual host controllers will depend on ISA,
PCI or a specific SOC.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Let architectures select the syscall support instead of duplicating the
kconfig entry.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the definitions to drivers/pci and let the architectures select
them. Two small differences to before: PCI_DOMAINS_GENERIC now selects
PCI_DOMAINS, cutting down the churn for modern architectures. As the
only architectured arm did previously also offer PCI_DOMAINS as a user
visible choice in addition to selecting it from the relevant configs,
this is gone now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
DWC2 hardware module integrated in Samsung SoCs requires some quirks to
operate properly, so use Samsung SoC specific compatible to notify driver
to apply respective fixes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The T3/R40/V40 using the same sdk and config file in allwinner
sdk, it seem they are the same SOC just with different name, so
compatible with R40.
The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors,
leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1/2 GB DDR3 DRAM
- 8 GB eMMC
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- 2 LVDS connectors
- 24 bit RGB LCD connector
- HDMI output
- DVP camera interface (support 500w cmos camera)
- GPIO connectors
- 5 TTL uarts and 2 RS232 uarts
- 1 RS485 connector
- support i2c capacitive tp and usb infrared tp
- boot control, reset and user buttons
- 3.5mm headphone and 3.5mm mic jack
- 100M RJ45
- micro SD card slot
- DC power jack
- RCT power slot
- 1 CVBS TVIN
- 1 CVBS TVOUT
- 2 customer leds
- 1 buzzer
- 1 minipcie
- I2C output
- SPI output
- PCM output
- wifi and bt connector reserved.
Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manual
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pwm-backlight driver initializes BLON (the enable gpio) to
output-high if the gpio is input on probe. Initializing the gpio
to output-low before the driver probes prevents this action by
the pwm-backlight driver and gets rid of a nasty blink of full
backlight with an uninitialized panel.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SAMA5D2 is different from SAMA5D3 and SAMA5D4, as there are two
different clocks for the peripherals in the SoC. The Static Memory
controller is connected to the divided master clock.
Unfortunately, the device tree does not correctly show this and uses the
master clock directly. This clock is then used by the code for the NAND
controller to calculate the timings for the controller, and we end up with
slow NAND Flash access.
Fix the device tree, and the performance of Flash access is improved.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add an ARM NEON implementation of NHPoly1305, an ε-almost-∆-universal
hash function used in the Adiantum encryption mode. For now, only the
NH portion is actually NEON-accelerated; the Poly1305 part is less
performance-critical so is just implemented in C.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the 32-bit ARM NEON implementation of ChaCha20 and XChaCha20
has been refactored to support varying the number of rounds, add support
for XChaCha12. This is identical to XChaCha20 except for the number of
rounds, which is 12 instead of 20.
XChaCha12 is faster than XChaCha20 but has a lower security margin,
though still greater than AES-256's since the best known attacks make it
through only 7 rounds. See the patch "crypto: chacha - add XChaCha12
support" for more details about why we need XChaCha12 support.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for adding XChaCha12 support, rename/refactor the NEON
implementation of ChaCha20 to support different numbers of rounds.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add an XChaCha20 implementation that is hooked up to the ARM NEON
implementation of ChaCha20. This is needed for use in the Adiantum
encryption mode; see the generic code patch,
"crypto: chacha20-generic - add XChaCha20 support", for more details.
We also update the NEON code to support HChaCha20 on one block, so we
can use that in XChaCha20 rather than calling the generic HChaCha20.
This required factoring the permutation out into its own macro.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To improve responsivesess, disable preemption for each step of the walk
(which is at most PAGE_SIZE) rather than for the entire
encryption/decryption operation.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for adding XChaCha12 support, rename/refactor
chacha20-generic to support different numbers of rounds. The
justification for needing XChaCha12 support is explained in more detail
in the patch "crypto: chacha - add XChaCha12 support".
The only difference between ChaCha{8,12,20} are the number of rounds
itself; all other parts of the algorithm are the same. Therefore,
remove the "20" from all definitions, structures, functions, files, etc.
that will be shared by all ChaCha versions.
Also make ->setkey() store the round count in the chacha_ctx (previously
chacha20_ctx). The generic code then passes the round count through to
chacha_block(). There will be a ->setkey() function for each explicitly
allowed round count; the encrypt/decrypt functions will be the same. I
decided not to do it the opposite way (same ->setkey() function for all
round counts, with different encrypt/decrypt functions) because that
would have required more boilerplate code in architecture-specific
implementations of ChaCha and XChaCha.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add sleep state for beeper pins. Without this there was a power
increase during the suspend and standby states on V3_3D domain.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl settings so that gpio0 wake from suspend will be supported
using buttons SW4 and SW7. Also, add pinctrl configuration for 0x954,
spi0_d0, which is an unused pin brought out to a header on the board
that in it's default state also connects to the gpio used for wakeup,
gpio0_3, which affects the state of the pin and prevents a working
wakeup unless we set the mux to a different state.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently uart0 uses pinctrl config set by bootloader so
create default state that can be restored after a suspend
event.
Also, modify uart0 pinctrl to include RTS and CTS pins as by
default these are not in a mode for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pins used by debugss are not configued by default, place pulldowns
on the pins for maximum power savings during sleep.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several pins on this EVM that are not in use but they can
still draw power if misconfigured. Create a pinctrl entry for these pins
and configure each one for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl data for ddr_vtt_toggle pin so that it is configured
for proper state during DeepSleep0. The pin should enter DS0 off mode
and hold the line low so VTT regulator is kept off while suspended.
It is also important for the PULLUP to be set on this pin so that
on removal of isolation, the VTT line is pulled high as a requirement
for bringing the DDR3 out of self-refresh.
This toggling is dependent on the IO isolation controlled by the
wkup_m3. Without placing the IOs into isolation the DS0 states set for
the pin will not be latched into effect during suspend.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As of commit d1dabab284 ("ARM: OMAP2+: Clean up
omap4_local_timer_init"), this header file is no longer used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x38b3c): Section mismatch in reference from
the function omap44xx_prm_late_init() to the function
.init.text:omap44xx_prm_enable_io_wakeup()
The function omap44xx_prm_late_init() references
the function __init omap44xx_prm_enable_io_wakeup().
This is often because omap44xx_prm_late_init lacks a __init
annotation or the annotation of omap44xx_prm_enable_io_wakeup is wrong.
Remove the __init annotation from omap44xx_prm_enable_io_wakeup so there
is no more mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When building the kernel with Clang, the following section mismatch
warnings appears:
WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.
WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.
WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.
_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EEPROM under I2C2 was put by mistake in the dts.
Remove it as it is not really present on the real hardware.
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Coreboot version on veyron ChromeOS devices seems to ignore
memory@0 nodes when updating the available memory and instead
inserts another memory node without the address.
This leads to 4GB systems only ever be using 2GB as the memory@0
node takes precedence. So remove the @0 for veyron devices.
Fixes: 0b639b815f ("ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards")
Cc: stable@vger.kernel.org
Reported-by: Heikki Lindholm <holin@iki.fi>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull ARM spectre updates from Russell King:
"These are the currently known final bits that resolve the Spectre
issues. big.Little systems used to be sufficiently identical in that
there were no differences between individual CPUs in the system that
mattered to the kernel. With the advent of the Spectre problem, the
CPUs now have differences in how the workaround is applied.
As a result of previous Spectre patches, these systems ended up
reporting quite a lot of:
"CPUx: Spectre v2: incorrect context switching function, system vulnerable"
messages due to the action of the big.Little switcher causing the CPUs
to be re-initialised regularly. This series resolves that issue by
making the CPU vtable unique to each CPU.
However, since this is used very early, before per-cpu is setup,
per-cpu can't be used. We also have a problem that two of the methods
are not called from preempt-safe paths, but thankfully these remain
identical between all CPUs in the system. To make sure, we validate
that these are identical during boot"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: spectre-v2: per-CPU vtables to work around big.Little systems
ARM: add PROC_VTABLE and PROC_TABLE macros
ARM: clean up per-processor check_bugs method call
ARM: split out processor lookup
ARM: make lookup_processor_type() non-__init
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We are taking care of setting secondary cpu boot address in
exynos_boot_secondary just before sending ipi to secondary CPUs,
so we can safely remove this setting from smp_prepare_cpus.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"Samsung PM Suspend debug" feature (controlled by SAMSUNG_PM_DEBUG
config option) is not working properly (debug messages are not
displayed after resume) on Exynos platforms because GPIOs restore
code is not implemented.
Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_DEBUG config option to hide it on Exynos platforms.
Then convert Exynos code to not require <plat/pm-common.h>
header (use pr_debug() directly instead of S3C_PMDBG() macro and
remove redundant s3c_pm_*() calls).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JYkZ
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Live from Vancouver, SoC maintainer talk, this weeks drm fixes pull
for rc3:
omapdrm:
- regression fixes for the reordering bridge stuff that went into rc1
i915:
- incorrect EU count fix
- HPD storm fix
- MST fix
- relocation fix for gen4/5
amdgpu:
- huge page handling fix
- IH ring setup
- XGMI aperture setup
- watermark setup fix
misc:
- docs and MST fix"
* tag 'drm-fixes-2018-11-16' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/i915: Account for scale factor when calculating initial phase
drm/i915: Clean up skl_program_scaler()
drm/i915: Move programming plane scaler to its own function.
drm/i915/icl: Drop spurious register read from icl_dbuf_slices_update
drm/i915: fix broadwell EU computation
drm/amdgpu: fix huge page handling on Vega10
drm/amd/pp: Fix truncated clock value when set watermark
drm/amdgpu: fix bug with IH ring setup
drm/meson: venc: dmt mode must use encp
drm/amdgpu: set system aperture to cover whole FB region
drm/i915: Fix hpd handling for pins with two encoders
drm/i915/execlists: Force write serialisation into context image vs execution
drm/i915/icl: Fix power well 2 wrt. DC-off toggling order
drm/i915: Fix NULL deref when re-enabling HPD IRQs on systems with MST
drm/i915: Fix possible race in intel_dp_add_mst_connector()
drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5
drm/omap: dsi: Fix missing of_platform_depopulate()
drm/omap: Move DISPC runtime PM handling to omapdrm
drm/omap: dsi: Ensure the device is active during probe
drm/omap: hdmi4: Ensure the device is active during bind
...
There are two common DTSI files for Exynos5422 Odroid XU3 family of
boards. One is shared between all of them (XU3, XU3-Lite, XU4 and HC1)
and the second skips HC1. Document this in the files.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
For consistency with arm64, where vendors have a single Kconfig symbol
in arch/arm64/Kconfig.platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Unlike all other family-specific Kconfig symbols for Renesas ARM SoCs,
ARCH_RZN1 is user-visible. As this symbol is already selected by the
SoC-specific ARCH_R9A06G032 symbol, there is no need for that.
Hide ARCH_RZN1 from the user, and move it up, where all other
family-specific Kconfig symbols live. Drop the select of CPU_V7, as
this is already implied by the dependency of ARCH_RENESAS on
ARCH_MULTI_V7.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a9863987b ("ARM: shmobile: Remove legacy SoC code
for SH-Mobile AG5"), this header file is no longer used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently support for the ARM Timer and Watchdog Unit is included
unconditionally, while only some Renesas multicore Cortex-A9 SoCs have
a TWD.
This decreases kernel image size by ca. 2 KiB on SoCs without a TWD.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently support for the ARM Cortex-A9 Snoop Control Unit is included
unconditionally, while only Renesas multicore Cortex-A9 SoCs have this
kind of SCU.
This decreases kernel image size by ca. 300 bytes on SoCs without such
an SCU.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove asm/hwcap.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Pixel Pipeline (PXP) block is present on several i.MX SoCs
such as imx6dl, imx6sl, imx6ul, imx6sx, imx6ull and imx7d.
Select the PXP driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows a board to specify a custom thermal zone configuration
involving the SoC internal sensor, CPU and GPU nodes without having
to change those nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the correct compatible for the new protocol used by the firmware
on the touch controller, the GPIO wakeup isn't used in that case.
Also eGalax touch needs axis swapping, just as with the RMI4 touch.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch corrects indentation problems in the gpmigrp and i2c1grp nodes.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wireless variants of the ConnecCore 6UL SOM include a Qualcomm
QCA6564 wireless chip with dual WiFi and Bluetooth.
Both the ConnectCore 6UL SBC Express and Pro boards fit a wireless SOM.
The Wifi is connected through the SDIO interface on usdhc1 and the
Bluetooth is connected via uart1.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the status property disable the PCIe, the property will be enable
by bootloader.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leave b{4,6}50v3 GPIO expander pca953x pins P05,P10,P11 unconfigured as
they are now used to implement an additional watchdog mechanism in user
space. P10,P11 pins remain unused (and therefore hogged) on b850v3.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for this board is currently very limited. To debug any potential
issues on this board the "earlycon" kernel parameter can be used (without
any arguments). However, this requires the board to define a
/chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Support for this board is currently very limited. To debug any potential
issues on this board the "earlycon" kernel parameter can be used (without
any arguments). However, this requires the board to define a
/chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Cc: patches@opensource.cirrus.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for Meson6 SoCs is currently very limited. It's often unclear
why such a device does not boot. To debug this the "earlycon" kernel
parameter can be used (without any arguments). However, this requires
the board to define a /chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- omap: Instantiate dss children in omapdss instead of mach (Laurent)
Other:
- htmldocs build warning (Sean)
- MST NULL deref fix (Stanislav)
- omap: Various runtime ref gets on probe/bind (Laurent)
- omap: Fix to the above dss children patch (Tony)
Cc: Sean Paul <sean@poorly.run>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlvsiL8ACgkQlvcN/ahK
Bwr1AQgAirnD41L7FDT2Y0sEBw2FH7MDlj8jw5Bb3qssaKCF/rqEKSG7Sx89n6os
idnPGonkRw8NOM10RMcSxJsG5PZK3lYzxU4QNrXOx+pqOsO/MUXvzMwSfLOK547s
BJTwIzgwh+ogR5yxH797IVZv1H5+DIavp7DPBc6J7e6ARLwJi5ZNBLVKCskPv8yX
Wvoo+pQFvtj7RCMHowtiiCmd6ryscsupEh3cYlHWxzcxCl0uIPOui9sxpet/60VI
4LgLCjAVd7VdzzQuMBbxkx2vFw9Z542ouBR9hk7WTYgzYt1gK2Xuc6h2fdX1g4Vk
jyhdGCvmhUZtxP96ahAunKxrb6/IjQ==
=f89R
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-11-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Cross-subsystem:
- omap: Instantiate dss children in omapdss instead of mach (Laurent)
Other:
- htmldocs build warning (Sean)
- MST NULL deref fix (Stanislav)
- omap: Various runtime ref gets on probe/bind (Laurent)
- omap: Fix to the above dss children patch (Tony)
Cc: Sean Paul <sean@poorly.run>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114204542.GA52569@art_vandelay
There is no functional change from this, but it is confusing to find two
copies of vcc_sys and no vcc_flash when looking in
/sys/class/regulator/*/name.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Simon Arlott <simon@arlott.org>
Cc: Kapil Hali <kapilh@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Pull ARM fix from Russell King:
"It was noticed that one of Julien's patches contained an error, this
fixes that up"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8810/1: vfp: Fix wrong assignement to ufp_exc
This new property allows the number of sensors to be configured from DT
instead of being hardcoded in platform data. Use it.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We've earlier added support to split the register address space into TM
and SROT regions. Split up the regmap address space into two for msm8974
that has a similar register layout.
Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT). This is OK since the
code doesn't really use the SROT functionality yet.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since commit d7c5f68635 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Fixes: d7c5f68635 ("ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813
regulator nodes")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[wens@csie.org: Reworked commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The i.MX25 contains two EPIT (Enhanced Periodic Interrupt Timer)
function blocks. Add their ipg and per clocks to the device tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set the eMMC max-frequency to 200MHz for optimal performance on Odroid
XU3/XU4 family of boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set the SD max-frequency to 200MHz for optimal performance on Odroid
XU3/XU4/HC1 family of boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
From Odroid XU3/XU4/HC1 schematics the LDO13 regulator for SD2, can be
set on 1.8V or 2.8V so the minimal value should be fixed to 1.8V. This
is necessary to support UHS-I tuning (otherwise card won't be detected
during boot).
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
