The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the GPIOs on the AXP209, we can control the LCD
backlight with them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 tablets follow the A23/A33 tablet reference design, and normally
use a "generic" 800x480 LCD panel. The actual panel may vary between
production runs, and there are no visible markings denoting its model.
This patch uses a panel that has the same dimensions and timings that
are close to what was provided in the vendor fex files.
Since there are also A33 Q8 tablets with 1024x600 panels, this patch
only sets the compatible string for A23 Q8 tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 design for A23/A33 tablets have an 18-bit RGB LCD panel connected
to the LCD interface on the SoC, the DC1SW output on the PMIC providing
power for the LCD, and PH7 toggling the reset pin for the panel.
This patch adds a device node for the panel, describing the above, and
enables the display pipeline.
The actual model or compatible string for the panel should be added in
the tablet device tree file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the compatible strings for the display pipeline on the A23 have
been added to the bindings, add the corresponding compatibles to the
device nodes already in the A23/A33 shared dtsi.
While the A23 has the TCON ch1 clock defined in the CCU, and the channel
1 registers are available, it does not have any means to use channel 1
due to a lack of downstream encoders, and the enable bit for channel 1 is
hard-wired to 0 (off). Hence the ch1 clock is left out.
As the MIPI DSI output device is not officially documented, and there
are no reference devices to test it, it is not covered by this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13 ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds nodes for the Video Engine and the associated reserved memory
for the A10. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A10 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, the board's
fixed 3.3V power regulator provides overall power via VBAT and I/O power
via VDDIO. The RTC clock output from the SoC provides the LPO low power
clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
CLK_OUT_A, an external clock output function driven from the clock
control unit, on the R40 is sometimes used to provide a low rate low
power clock to a WiFi or Bluetooth controller.
This patch adds a pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
UART3 on the PG pingroup on the R40 SoC is commonly used to connect the
bluetooth controller in a WiFi+Bluetooth combo chip, with the WiFi bits
also on the PG pingroup.
This patch adds two device nodes for UART3 on PG pingroup, one for the
RX/TX pins, and one for the RTS/CTS pins. Consumers can reference either
just the RX/TX pinmux setting or both, depending on the application.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The bananapi has all its bank regulators tied to the 3v3 static regulator.
Make sure it's properly represented.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on cubieboard with 'perf stat echo foo'.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 9c2af1c737 ("kbuild: add .DELETE_ON_ERROR special
target"), the target file is automatically deleted on failure.
The boilerplate code
... || { rm -f $@; false; }
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Pull vfs mount API prep from Al Viro:
"Mount API prereqs.
Mostly that's LSM mount options cleanups. There are several minor
fixes in there, but nothing earth-shattering (leaks on failure exits,
mostly)"
* 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (27 commits)
mount_fs: suppress MAC on MS_SUBMOUNT as well as MS_KERNMOUNT
smack: rewrite smack_sb_eat_lsm_opts()
smack: get rid of match_token()
smack: take the guts of smack_parse_opts_str() into a new helper
LSM: new method: ->sb_add_mnt_opt()
selinux: rewrite selinux_sb_eat_lsm_opts()
selinux: regularize Opt_... names a bit
selinux: switch away from match_token()
selinux: new helper - selinux_add_opt()
LSM: bury struct security_mnt_opts
smack: switch to private smack_mnt_opts
selinux: switch to private struct selinux_mnt_opts
LSM: hide struct security_mnt_opts from any generic code
selinux: kill selinux_sb_get_mnt_opts()
LSM: turn sb_eat_lsm_opts() into a method
nfs_remount(): don't leak, don't ignore LSM options quietly
btrfs: sanitize security_mnt_opts use
selinux; don't open-code a loop in sb_finish_set_opts()
LSM: split ->sb_set_mnt_opts() out of ->sb_kern_mount()
new helper: security_sb_eat_lsm_opts()
...
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
- Florian Fainelli noticed that userspace segfaults caused by the lack
of kernel-userspace helpers was hard to diagnose; we now issue a
warning when userspace tries to use the helpers but the kernel has
them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with DT
systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in 4.20
(which had the effect that data that can be placed into the init
sections was incorrectly always placed in the rodata section.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Yl96
-----END PGP SIGNATURE-----
Merge tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Included in this update:
- Florian Fainelli noticed that userspace segfaults caused by the
lack of kernel-userspace helpers was hard to diagnose; we now issue
a warning when userspace tries to use the helpers but the kernel
has them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with
DT systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in
4.20 (which had the effect that data that can be placed into the
init sections was incorrectly always placed in the rodata section)"
* tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm: (25 commits)
ARM: omap2: remove unnecessary boot_lock
ARM: versatile: rename and comment SMP implementation
ARM: versatile: convert boot_lock to raw
ARM: vexpress/realview: consolidate immitation CPU hotplug
ARM: fix the cockup in the previous patch
ARM: sa1100/cerf: switch to using gpio_led_register_device()
ARM: sa1100/assabet: switch to using gpio leds
ARM: sa1100/assabet: add gpio keys support for right-hand two buttons
ARM: sa1111: remove legacy GPIO interfaces
pcmcia: sa1100*: remove redundant bvd1/bvd2 setting
ARM: pxa/lubbock: switch PCMCIA to MAX1600 library
ARM: pxa/mainstone: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/neponset: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/jornada720: switch PCMCIA to gpiod APIs
pcmcia: add MAX1600 library
ARM: sa1100: explicitly register sa11x0-pcmcia devices
ARM: 8813/1: Make aligned 2-byte getuser()/putuser() atomic on ARMv6+
ARM: 8812/1: Optimise copy_{from/to}_user for !CPU_USE_DOMAINS
ARM: 8811/1: always list both ldrd/strd registers explicitly
ARM: 8808/1: kexec:offline panic_smp_self_stop CPU
...
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Merge in a few missing patches from the pull request (my copy of the
branch was behind the staged version in linux-next).
* next/drivers:
memory: pl353: Add driver for arm pl353 static memory controller
dt-bindings: memory: Add pl353 smc controller devicetree binding information
firmware: qcom: scm: fix compilation error when disabled
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the UniPhier MIO DMAC driver. This is used as the DMA engine
for accelerating the SD/eMMC controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mostly clean ups although whilst Doug's was chasing down a odd
lockdep warning he also did some work to improved debugger resilience
when some CPUs fail to respond to the round up request.
The main changes are:
* Fixing a lockdep warning on architectures that cannot use an NMI for
the round up plus related changes to make CPU round up and all CPU
backtrace more resilient.
* Constify the arch ops tables
* A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope
(and directly related to kgdb). Didn't get comprehensive acks but
all impacted maintainers were Cc:ed in good time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=Aqlc
-----END PGP SIGNATURE-----
Merge tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Mostly clean ups although while Doug's was chasing down a odd lockdep
warning he also did some work to improved debugger resilience when
some CPUs fail to respond to the round up request.
The main changes are:
- Fixing a lockdep warning on architectures that cannot use an NMI
for the round up plus related changes to make CPU round up and all
CPU backtrace more resilient.
- Constify the arch ops tables
- A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope (and
directly related to kgdb). Didn't get comprehensive acks but all
impacted maintainers were Cc:ed in good time"
* tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kgdb/treewide: constify struct kgdb_arch arch_kgdb_ops
mips/kgdb: prepare arch_kgdb_ops for constness
kdb: use bool for binary state indicators
kdb: Don't back trace on a cpu that didn't round up
kgdb: Don't round up a CPU that failed rounding up before
kgdb: Fix kgdb_roundup_cpus() for arches who used smp_call_function()
kgdb: Remove irq flags from roundup
Most changes here are to enable new drivers and platforms in the various
configs that affect them. Most of these have been covered and described
in the other branches, we mostly keep defconfig separate to avoid
conflicts between SoC/dt/driver updates that they otherwise would be
grouped with.
One thing worth mentioning here is that OMAP changes from using their
own UART driver, to 8250, for the multi_v7_defconfig shared config on
32-bit. This means that the console is now named ttyS* instead of ttyO*.
This change was already done for omap2_defconfig a while back, so most
users of these configs have either already updated, or can easily follow
the same patterns as they did at that time. This makes platform support
slightly easier for distros, since they no longer need to keep track of
a separate console prefix for these platforms.
-----BEGIN PGP SIGNATURE-----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=65qL
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Most changes here are to enable new drivers and platforms in the
various configs that affect them. Most of these have been covered and
described in the other branches, we mostly keep defconfig separate to
avoid conflicts between SoC/dt/driver updates that they otherwise
would be grouped with.
One thing worth mentioning here is that OMAP changes from using their
own UART driver, to 8250, for the multi_v7_defconfig shared config on
32-bit. This means that the console is now named ttyS* instead of
ttyO*. This change was already done for omap2_defconfig a while back,
so most users of these configs have either already updated, or can
easily follow the same patterns as they did at that time. This makes
platform support slightly easier for distros, since they no longer
need to keep track of a separate console prefix for these platforms"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
Revert "arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO"
arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO
arm64: defconfig: Replace PINCTRL_MT7622 with PINCTRL_MTK_MOORE
arm64: defconfig: Regenerate for v4.20
ARM: multi_v7_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: multi_v7_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: exynos_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add MAX8998 RTC and charger drivers
ARM: imx_v6_v7_defconfig: add imx7ulp support
ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
ARM: multi_v7_defconfig: enable STM32 analog & timer drivers
arm64: defconfig: Enable GCC and PINCTRL for MSM8998
arm64: defconfig: Enable core Qualcomm SDM845 options
ARM: defconfig: Enable the PL111 DRM driver on vexpress
ARM: defconfig: Update the vexpress defconfig
arm64: defconfig: Enable some qcom remoteproc configs
arm64: defconfig: Enable QCS404 configs
ARM: imx_v6_v7_defconfig: Enable USB_ANNOUNCE_NEW_DEVICES
ARM: imx_v6_v7_defconfig: Enable BT_BNEP
...
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
+ misc cleanups across several platforms
-----BEGIN PGP SIGNATURE-----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=yEX2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
-----------
- Following pen_release and boot_lock cleanup initiated by
Russell King, .smp_prepare_cpus and .smp_boot_secondary STi callbacks
must be reworked to keep secondary CPU's bringup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcG50AAAoJEMrHeC97M/+m1CMP+wYY5OagpvTabaJ5AJZA68Jn
vLqGrrfch5XxaGe9OL5bxk0ndv3mmyD4ydAD9EwJBzwSbjM7QKH0E+8pTZcLVc2z
i3R54Wdd49m2vX7NFPEZF/dMS+AZ+C7cmWiGYrNyJxktXPaTzhO5XwXoRr2yUyBV
MBw4qOyhwqRPWGuEud0FTqXpQ46zoVFIwXDcMHwdvM1CyPiNCzYqFzyyy28RXqhX
pr3VWHw9nRA7+1XqUVrU81Uu/Fyk/pidpmngM7xsG1NzdmZu6s//LlWoGRuH9u7k
a6jiZ94HC5tmGoA3Fx32b95hS2eWvjewIDzj48t6kuzJjCDzwQOXGoOLunQUuY/8
jcg0BF+0d5Efq9GKXVJaZ4XHt15XomwG+CDsjhDyU3HDBN1muB8rF7/2oXzAc4NL
D+OGebnrCZlWlFM8YpWcYc/2tZBoT2DhtpuiKFHe6ExLIw/dqk2KilFzghisyHt/
lZh21JJtqVTEcd2GaQVALbQlcJZj8VaRVVGjdniuysqdMBoMCfT4hAzIVzXjybzK
qUrmR7wRAiidI0URCXPaMhhRGmvZbssQiPA8aI6LCauAkxuPDOFPfkDn+eX5KsXn
SqPlfDNOEfEPz4gJOAclVRV/1kBBLmAe/iIE39Z5Gy8A9cNMdqn1KxrrEjSUJcwU
GXzUvpyajj04OGCM2InI
=QbVn
-----END PGP SIGNATURE-----
Merge tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/late
Highlights:
-----------
- Following pen_release and boot_lock cleanup initiated by
Russell King, .smp_prepare_cpus and .smp_boot_secondary STi callbacks
must be reworked to keep secondary CPU's bringup.
* tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: sti: remove pen_release and boot_lock
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAlwZT90QHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD1+TxD/9eHjeon87f2f61FlO+u9+gN+kSwn1hwSj+
bsz6GG0CuG5WWX5Lr8K5Uu+wtxEOfN4d1VoMH7rFiznkGxE5YpZc0hiK1qwsKtos
E8IAAFjC+C4DpH8q1mojF9pSnLVpn+BFXsfR1JI4hgxrfwTKWJ8BJaNFdWOfFsyG
1UduKVXgftnSF+iSVeX5vTRsQpBKPlm/5/ULhPyvJ+la9LzE6ZJ0E8hW3EgLtzQx
T5BPyZlrd48EJHinO5imBy+h5z5Ca7Hg23twtBJC4ei0Zbc7KHXY6xxpKab7qLcs
Zzs29R3PyNuOg1RTzZsIA+RxiytbRNjHhuPaP8XQa0i9WxkMgRRG7ITn2L4hLYvb
ufME4mnQ4K8hCooV96gJvfzy9T5NYrNnmcKKnNLeAkcWHV/nXEyPVGXUYVMwTdev
Zs9FWfn1E2fjCGu0sHp+PMQZXarEI0uC7tOnGROOHHKIxaH2Pf2OltVfJhGg29yu
4+JCVJju/G328RfYgjb/GDoU1WHl+5mhs0NQxjxdG6cV83K7sNeUMMv+2se5NlRD
xZYEAovzGogcOrOc1NlNzOQBwZlXdtFVz45em6qRFPomURgtLQuMZWSpPscRvajH
Pn0FPK2ah80n8rSeHWx3nNuuUZcGT1g1muM3zxshNy+jOHwHzyM8Gp5fjrNQzZ4Q
93jGdUPmMw==
=dIrg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge in fixes here, since the last batch didn't make it in before the
release of 4.20, and we might as well group them with this set of
patches.
* fixes: (822 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: realview: Fix some more duplicate regulator nodes
MAINTAINERS: update entry for MMP platform
ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dt
MAINTAINERS: mediatek: Update SoC entry
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
+ Linux 4.20-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
checkpatch.pl reports the following:
WARNING: struct kgdb_arch should normally be const
#28: FILE: arch/mips/kernel/kgdb.c:397:
+struct kgdb_arch arch_kgdb_ops = {
This report makes sense, as all other ops struct, this
one should also be const. This patch does the change.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: x86@kernel.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
