There are some duplicated codes in ipvlan_add_addr6/4 and
ipvlan_del_addr6/4. Now define two common functions ipvlan_add_addr
and ipvlan_del_addr to decrease the duplicated codes.
It could be helful to maintain the codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes: 4bfcbd7abc ("stmmac: Move the mdio_register/_unregister in probe/remove")
Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit beb0babfb7 ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb7 ("korina: disable napi on close and restart")
Reported-by: Alexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The user prio field is wrong (and overflows) in the XDP forward
flow.
This is a result of a bad value for num_tx_rings_p_up, which should
account all XDP TX rings, as they operate for the same user prio.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an IPvlan setup when master is set in loopback mode e.g.
ethtool -K eth0 set loopback on
where eth0 is master device for IPvlan setup.
The failure is caused by the faulty logic that determines if the
packet is from TX-path vs. RX-path by just looking at the mac-
addresses on the packet while processing multicast packets.
In the loopback-mode where this crash was happening, the packets
that are sent out are reflected by the NIC and are processed on
the RX path, but mac-address check tricks into thinking this
packet is from TX path and falsely uses dev_forward_skb() to pass
packets to the slave (virtual) devices.
This patch records the path while queueing packets and eliminates
logic of looking at mac-addresses for the same decision.
------------[ cut here ]------------
kernel BUG at include/linux/skbuff.h:1737!
Call Trace:
[<ffffffff921fbbc2>] dev_forward_skb+0x92/0xd0
[<ffffffffc031ac65>] ipvlan_process_multicast+0x395/0x4c0 [ipvlan]
[<ffffffffc031a9a7>] ? ipvlan_process_multicast+0xd7/0x4c0 [ipvlan]
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91cdff09>] process_one_work+0x1a9/0x660
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91ce086d>] worker_thread+0x11d/0x360
[<ffffffff91ce0750>] ? rescuer_thread+0x350/0x350
[<ffffffff91ce960b>] kthread+0xdb/0xe0
[<ffffffff91c05c70>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
[<ffffffff92348b7a>] ret_from_fork+0x9a/0xd0
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
Fixes: ba35f8588f ("ipvlan: Defer multicast / broadcast processing to a work-queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) netif_rx() / dev_forward_skb() should not be called from process
context.
2) ipvlan_count_rx() should be called with preemption disabled.
3) We should check if ipvlan->dev is up before feeding packets
to netif_rx()
4) We need to prevent device from disappearing if some packets
are in the multicast backlog.
5) One kfree_skb() should be a consume_skb() eventually
Fixes: ba35f8588f ("ipvlan: Defer multicast / broadcast processing to
a work-queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) We have to be careful to not try and place a checksum after the end
of a rawv6 packet, fix from Dave Jones with help from Hannes
Frederic Sowa.
2) Missing memory barriers in tcp_tasklet_func() lead to crashes, from
Eric Dumazet.
3) Several bug fixes for the new XDP support in virtio_net, from Jason
Wang.
4) Increase headroom in RX skbs in be2net driver to accomodate
encapsulations such as geneve. From Kalesh A P.
5) Fix SKB frag unmapping on TX in mvpp2, from Thomas Petazzoni.
6) Pre-pulling UDP headers created a regression in RECVORIGDSTADDR
socket option support, from Willem de Bruijn.
7) UID based routing added a potential OOPS in ip_do_redirect() when we
see an SKB without a socket attached. We just need it for the
network namespace which we can get from skb->dev instead. Fix from
Lorenzo Colitti.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
sctp: fix recovering from 0 win with small data chunks
sctp: do not loose window information if in rwnd_over
virtio-net: XDP support for small buffers
virtio-net: remove big packet XDP codes
virtio-net: forbid XDP when VIRTIO_NET_F_GUEST_UFO is support
virtio-net: make rx buf size estimation works for XDP
virtio-net: unbreak csumed packets for XDP_PASS
virtio-net: correctly handle XDP_PASS for linearized packets
virtio-net: fix page miscount during XDP linearizing
virtio-net: correctly xmit linearized page on XDP_TX
virtio-net: remove the warning before XDP linearizing
mlxsw: spectrum_router: Correctly remove nexthop groups
mlxsw: spectrum_router: Don't reflect dead neighs
neigh: Send netevent after marking neigh as dead
ipv6: handle -EFAULT from skb_copy_bits
inet: fix IP(V6)_RECVORIGDSTADDR for udp sockets
net/sched: cls_flower: Mandate mask when matching on flags
net/sched: act_tunnel_key: Fix setting UDP dst port in metadata under IPv6
stmmac: CSR clock configuration fix
net: ipv4: Don't crash if passing a null sk to ip_do_redirect.
...
Commit f600b69050 ("virtio_net: Add XDP support") leaves the case of
small receive buffer untouched. This will confuse the user who want to
set XDP but use small buffers. Other than forbid XDP in small buffer
mode, let's make it work. XDP then can only work at skb->data since
virtio-net create skbs during refill, this is sub optimal which could
be optimized in the future.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we in fact don't allow XDP for big packets, remove its codes.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VIRTIO_NET_F_GUEST_UFO is negotiated, host could still send UFO
packet that exceeds a single page which could not be handled
correctly by XDP. So this patch forbids setting XDP when GUEST_UFO is
supported. While at it, forbid XDP for ECN (which comes only from GRO)
too to prevent user from misconfiguration.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't update ewma rx buf size in the case of XDP. This will lead
underestimation of rx buf size which causes host to produce more than
one buffers. This will greatly increase the possibility of XDP page
linearization.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We drop csumed packet when do XDP for packets. This breaks
XDP_PASS when GUEST_CSUM is supported. Fix this by allowing csum flag
to be set. With this patch, simple TCP works for XDP_PASS.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XDP_PASS were determined for linearized packets, we try to get
new buffers in the virtqueue and build skbs from them. This is wrong,
we should create skbs based on existed buffers instead. Fixing them by
creating skb based on xdp_page.
With this patch "ping 192.168.100.4 -s 3900 -M do" works for XDP_PASS.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't put page during linearizing, the would cause leaking when
xmit through XDP_TX or the packet exceeds PAGE_SIZE. Fix them by
put page accordingly. Also decrease the number of buffers during
linearizing to make sure caller can free buffers correctly when packet
exceeds PAGE_SIZE. With this patch, we won't get OOM after linearize
huge number of packets.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we linearize page, we should xmit this page instead of the page
of first buffer which may lead unexpected result. With this patch, we
can see correct packet during XDP_TX.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use EWMA to estimate the size of rx buffer. When rx buffer
size is underestimated, it's usual to have a packet with more than one
buffers. Consider this is not a bug, remove the warning and correct
the comment before XDP linearizing.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly stuff which missed the initial pull. There's a new
driver: qedi, some ufs, ibmvscsis and ncr5380 updates plus some
assorted driver fixes and also a fix for the bug where if a device
goes into a blocked state between configuration and sysfs device add
(which can be a long time under async probing) it would become
permanently blocked.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zofc
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull late SCSI updates from James Bottomley:
"This is mostly stuff which missed the initial pull.
There's a new driver: qedi, and some ufs, ibmvscsis and ncr5380
updates plus some assorted driver fixes and also a fix for the bug
where if a device goes into a blocked state between configuration and
sysfs device add (which can be a long time under async probing) it
would become permanently blocked"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: avoid a permanent stop of the scsi device's request queue
scsi: mpt3sas: Recognize and act on iopriority info
scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.
scsi: qla2xxx: Add Block Multi Queue functionality.
scsi: qla2xxx: Add multiple queue pair functionality.
scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.
scsi: qla2xxx: Only allow operational MBX to proceed during RESET.
scsi: hpsa: remove memory allocate failure message
scsi: Update 3ware driver email addresses
scsi: zfcp: fix rport unblock race with LUN recovery
scsi: zfcp: do not trace pure benign residual HBA responses at default level
scsi: zfcp: fix use-after-"free" in FC ingress path after TMF
scsi: libcxgbi: return error if interface is not up
scsi: cxgb4i: libcxgbi: add missing module_put()
scsi: cxgb4i: libcxgbi: cxgb4: add T6 iSCSI completion feature
scsi: cxgb4i: libcxgbi: add active open cmd for T6 adapters
scsi: cxgb4i: use cxgb4_tp_smt_idx() to get smt_idx
scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.
scsi: aacraid: remove wildcard for series 9 controllers
scsi: ibmvscsi: add write memory barrier to CRQ processing
...
At the end of the nexthop initialization process we determine whether
the nexthop should be offloaded or not based on the NUD state of the
neighbour representing it. After all the nexthops were initialized we
refresh the nexthop group and potentially offload it to the device, in
case some of the nexthops were resolved.
Make the destruction of a nexthop group symmetric with its creation by
marking all nexthops as invalid and then refresh the nexthop group to
make sure it was removed from the device's tables.
Fixes: b2157149b0 ("mlxsw: spectrum_router: Add the nexthop neigh activity update")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a neighbour is considered to be dead, we should remove it from the
device's table regardless of its NUD state.
Without this patch, after setting a port to be administratively down we
get the following errors when we periodically try to update the kernel
about neighbours activity:
[ 461.947268] mlxsw_spectrum 0000:03:00.0 sw1p3: Failed to find
matching neighbour for IP=192.168.100.2
Fixes: a6bf9e933d ("mlxsw: spectrum_router: Offload neighbours based on NUD state change")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing stmmac with my QoS reference design I checked a problem in the
CSR clock configuration that was impossibilitating the phy discovery, since
every read operation returned 0x0000ffff. This patch fixes the issue.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All small fixes this time, especially important are the regression
fixes for rtlwifi and ath9k.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYW+jGAAoJEG4XJFUm622bFIUH/isc9kpL63eJOwKr6P0Uow92
XF+OcrnhRxlVqAsMx0yvrNsVAIZkLfAjJhLZv91h5Vpv0UCnLP4LpH1IqwiHih1u
oxZVbcV7qAOZopgvWDU8R2Nh6Z4FPWYmDttvg86rQKLh82DuNCvl+btl/cCFaVDS
5T1xpY+BP2CbIUyTJ3Sg1t4yZI06dZODaLuiFzxM1MjEhQ0p785VJBASekLzo6YE
6YMzDIP6iir/WKod9HXtJJIgv+gBiZMCTmw7QH+G2o/i3WIjclqsSSwCepDCpmlI
AuicYeeObWPOQFpCpD4KgrshdLM/zytLuRvaU8lVofr81I98Hs8rHBbYJTwZsGE=
=kA4D
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
All small fixes this time, especially important are the regression
fixes for rtlwifi and ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix: Addresses should be printed using the %p format specifier
rather than using %x.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 71ce391dfb ("net: mvpp2: enable proper per-CPU TX
buffers unmapping"), we are not correctly DMA unmapping TX buffers for
fragments.
Indeed, the mvpp2_txq_inc_put() function only stores in the
txq_cpu->tx_buffs[] array the physical address of the buffer to be
DMA-unmapped when skb != NULL. In addition, when DMA-unmapping, we use
skb_headlen(skb) to get the size to be unmapped. Both of this works fine
for TX descriptors that are associated directly to a SKB, but not the
ones that are used for fragments, with a NULL pointer as skb:
- We have a NULL physical address when calling DMA unmap
- skb_headlen(skb) crashes because skb is NULL
This causes random crashes when fragments are used.
To solve this problem, we need to:
- Store the physical address of the buffer to be unmapped
unconditionally, regardless of whether it is tied to a SKB or not.
- Store the length of the buffer to be unmapped, which requires a new
field.
Instead of adding a third array to store the length of the buffer to be
unmapped, and as suggested by David Miller, this commit refactors the
tx_buffs[] and tx_skb[] arrays of 'struct mvpp2_txq_pcpu' into a
separate structure 'mvpp2_txq_pcpu_buf', to which a 'size' field is
added. Therefore, instead of having three arrays to allocate/free, we
have a single one, which also improve data locality, reducing the
impact on the CPU cache.
Fixes: 71ce391dfb ("net: mvpp2: enable proper per-CPU TX buffers unmapping")
Reported-by: Raphael G <raphael.glon@corp.ovh.com>
Cc: Raphael G <raphael.glon@corp.ovh.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the dwmac-rk tries to set up the GRF-specific speed and link
options before enabling clocks, phys etc and on previous socs this works
because the GRF is supplied on the whole by one clock.
On the rk3399 however the GRF (General Register Files) clock-supply
has been split into multiple clocks and while there is no specific
grf-gmac clock like for other sub-blocks, it seems the mac-specific
portions are actually supplied by the general mac clock.
This results in hangs on rk3399 boards if the driver is build as module.
When built in te problem of course doesn't surface, as the clocks
are of course still on at the stage before clock_disable_unused.
To solve this, simply move the clock enablement to the first position
in the powerup callback. This is also a good idea in general to
enable clocks before everything else.
Tested on rk3288, rk3368 and rk3399 the dwmac still works on all of them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently allocates 128 bytes of skb headroom.
This was found to be insufficient with some configurations
like Geneve tunnels, which resulted in skb head reallocations.
Increase the headroom to 256 bytes to fix this.
Signed-off-by: Kalesh A P <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit e496561473 {"rtlwifi: Use dev_kfree_skb_irq instead of
kfree_skb"), the method used to free an skb was changed because the
kfree_skb() was inside a spinlock. What was forgotten is that kfree_skb()
guards against a NULL value for the argument. Routine dev_kfree_skb_irq()
does not, and a test is needed to prevent kernel panics.
Fixes: e496561473 ("rtlwifi: Use dev_kfree_skb_irq instead of kfree_skb")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.9+
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
there are two drivers for Solarflare devices, but both still show up
directly beneath "Ethernet driver support" in the Kconfig. Follow the
pattern of other vendors and group them beneath an own vendor Kconfig
entry for Solarflare.
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change its compatible string.
So we should name all the compatible string with the suffix "-gmac".
Creating a new name suffix "-gemac" is unnecessary.
We also add another SoC compatible string in dt binding documentation
and describe which generic version the SoC belongs to.
Fixes: d0fb6ba75d ("net: hix5hd2_gmac: add generic compatible string")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing 10gbe host port tx priority map
configurations.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool ops, it needs to retrieve the corresponding
ethss module (gbe or xgbe) from the net_device structure.
Prior to this patch, the retrieving procedure only
checks for the gbe module. This patch fixes the issue
by checking the xgbe module if the net_device structure
does not correspond to the gbe module.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl/fman drivers will use of_platform_populate() on all
supported platforms. Call of_platform_populate() to probe the
FMan sub-nodes.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
QSGMII ports were not advertising 1G speed.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In genphy_config_eee_advert, the return value of phy_read_mmd_indirect is
checked to know if the register could be accessed but the result is
assigned to a 'u32'.
Changing to 'int' to correctly get errors from phy_read_mmd_indirect.
Fixes: d853d145ea ("net: phy: add an option to disable EEE advertisement")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scheduled scan ssid configuration in firmware has a flags field that
was not initialized resulting in unexpected behaviour.
Fixes: e3bdb7cc0300 ("brcmfmac: fix handling ssids in .sched_scan_start() callback")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_cfg80211_attach() there was one error path not properly
handled as it leaked memory allocated in brcmf_btcoex_attach().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix up memory barriers in stmmac driver. They are meant to protect
against DMA engine, so smp_ variants are certainly wrong, and dma_
variants are preferable.
Signed-off-by: Pavel Machek <pavel@denx.de>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, If devm_ioremap will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
The build of sparc allmodconfig fails with the error:
"of_irq_to_resource" [drivers/net/ethernet/marvell/mv643xx_eth.ko]
undefined!
of_irq_to_resource() is defined when CONFIG_OF_IRQ is defined. And also
CONFIG_OF_IRQ can only be defined if CONFIG_IRQ is defined. So we can
safely use #if defined(CONFIG_OF_IRQ) in the code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is split we should mark it as such, as otherwise the split
ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit
operation fails:
$ devlink port split sw1p3 count 4
$ devlink port unsplit eth0
devlink answers: Invalid argument
[ 598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split
Fixes: 67963a33b4 ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Reviewed-by: Elad Raz <eladr@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added file causes a harmless warning, with "make W=1":
drivers/net/ethernet/qlogic/qed/qed_iscsi.c: In function 'qed_get_iscsi_ops':
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:1268:29: warning: old-style function definition [-Wold-style-definition]
This makes it a proper prototype.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 99d8d2159d ("irda: w83977af_ir: Neaten logging"), we
accidentally added an extra tab to these lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating a GTPv1 header in gtp1_push_header(), initialize the
'reserved' bit to zero. All 3GPP specifications for GTPv1 from Release
99 through Release 13 agree that a transmitter shall set this bit to
zero, see e.g. Note 0 of Figure 2 in Section 6 of 3GPP TS 29.060 v13.5.0
Release 13, available from
http://www.etsi.org/deliver/etsi_ts/129000_129099/129060/13.05.00_60/ts_129060v130500p.pdf
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gtp_check_src_ms_ipv4() did not find the PDP context matching with the
UE IP address because the memory location is not right, but the result
is inverted by the Boolean "not" operator. So whatever is the PDP
context, any call to this function is successful.
Signed-off-by: Lionel Gauthier <Lionel.Gauthier@eurecom.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net XDP support expects receive buffers to be contiguous.
If this is not the case we enable a slowpath to allow connectivity
to continue but at a significan performance overhead associated with
linearizing data. To make it painfully aware to users that XDP is
running in a degraded mode we throw an xdp buffer error.
To linearize packets we allocate a page and copy the segments of
the data, including the header, into it. After this the page can be
handled by XDP code flow as normal.
Then depending on the return code the page is either freed or sent
to the XDP xmit path. There is no attempt to optimize this path.
This case is being handled simple as a precaution in case some
unknown backend were to generate packets in this form. To test this
I had to hack qemu and force it to generate these packets. I do not
expect this case to be generated by "real" backends.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the XDP_TX action to virtio_net. When an XDP
program is run and returns the XDP_TX action the virtio_net XDP
implementation will transmit the packet on a TX queue that aligns
with the current CPU that the XDP packet was processed on.
Before sending the packet the header is zeroed. Also XDP is expected
to handle checksum correctly so no checksum offload support is
provided.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP requires using isolated transmit queues to avoid interference
with normal networking stack (BQL, NETDEV_TX_BUSY, etc). This patch
adds a XDP queue per cpu when a XDP program is loaded and does not
expose the queues to the OS via the normal API call to
netif_set_real_num_tx_queues(). This way the stack will never push
an skb to these queues.
However virtio/vhost/qemu implementation only allows for creating
TX/RX queue pairs at this time so creating only TX queues was not
possible. And because the associated RX queues are being created I
went ahead and exposed these to the stack and let the backend use
them. This creates more RX queues visible to the network stack than
TX queues which is worth mentioning but does not cause any issues as
far as I can tell.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds XDP support to virtio_net. Some requirements must be
met for XDP to be enabled depending on the mode. First it will
only be supported with LRO disabled so that data is not pushed
across multiple buffers. Second the MTU must be less than a page
size to avoid having to handle XDP across multiple pages.
If mergeable receive is enabled this patch only supports the case
where header and data are in the same buf which we can check when
a packet is received by looking at num_buf. If the num_buf is
greater than 1 and a XDP program is loaded the packet is dropped
and a warning is thrown. When any_header_sg is set this does not
happen and both header and data is put in a single buffer as expected
so we check this when XDP programs are loaded. Subsequent patches
will process the packet in a degraded mode to ensure connectivity
and correctness is not lost even if backend pushes packets into
multiple buffers.
If big packets mode is enabled and MTU/LRO conditions above are
met then XDP is allowed.
This patch was tested with qemu with vhost=on and vhost=off where
mergeable and big_packet modes were forced via hard coding feature
negotiation. Multiple buffers per packet was forced via a small
test patch to vhost.c in the vhost=on qemu mode.
Suggested-by: Shrijeet Mukherjee <shrijeet@gmail.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure correct access to the big endian QMan HW through proper
accessors.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,
$ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE
$ ping -I red -c1 11.1.1.3
ping: Warning: source address might be selected on device other than red.
PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
ping: sendmsg: Operation not permitted
Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).
Call nf_reset to drop the conntrack info following the pass through the
VRF device. The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.
Fixes: 8f58336d3f ("net: Add ethernet header for pass through VRF device")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connection tracking with VRF is broken because the pass through the VRF
device drops the connection tracking info. Removing the call to nf_reset
allows DNAT and MASQUERADE to work across interfaces within a VRF.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are hardware PCI implementations of Cadence GEM network
controller. This patch will allow to use such hardware with reuse of
existing Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ACPI systems, clocks are not available to drivers directly. They are
handled exclusively by ACPI and/or firmware, so there is no clock driver.
Calls to clk_get() always fail, so we should not even attempt to claim
any clocks on ACPI systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before, encx24j600_rx_packets did not update encx24j600_priv's next_packet
member when an error occurred during packet handling (either because the
packet's RSV header indicates an error or because the encx24j600_receive_packet
method can't allocate an sk_buff).
If the next_packet member is not updated, the ERXTAIL register will be set to
the same value it had before, which means the bad packet remains in the
component's memory and its RSV header will be read again when a new packet
arrives. If the RSV header indicates a bad packet or if sk_buff allocation
continues to fail, new packets will be stored in the component's memory until
that memory is full, after which packets will be dropped.
The SETPKTDEC command is always executed though, so the encx24j600 hardware has
an incorrect count of the packets in its memory.
To prevent this, the next_packet member should always be updated, allowing the
packet to be skipped (either because it's bad, as indicated in its RSV header,
or because allocating an sk_buff failed). In the allocation failure case, this
does mean dropping a valid packet, but dropping the oldest packet to keep as
much memory as possible available for new packets seems preferable to keeping
old (but valid) packets around while dropping new ones.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hip04 driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hisi_femac driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer handling in this driver is broken in several ways:
- corkscrew_open() initializes and arms a timer before requesting the
device interrupt. If the request fails the timer stays armed.
A second call to corkscrew_open will unconditionally reinitialize the
quued timer and arm it again. Also a immediate device removal will leave
the timer queued because close() is not called (open() failed) and
therefore nothing issues del_timer().
The reinitialization corrupts the link chain in the timer wheel hash
bucket and causes a NULL pointer dereference when the timer wheel tries
to operate on that hash bucket. Immediate device removal lets the link
chain poke into freed and possibly reused memory.
Solution: Arm the timer after the successful irq request.
- corkscrew_close() uses del_timer()
On close the timer is disarmed with del_timer() which lets the following
code race against a concurrent timer expiry function.
Solution: Use del_timer_sync() instead
- corkscrew_close() calls del_timer() unconditionally
del_timer() is invoked even if the timer was never initialized. This
works by chance because the struct containing the timer is zeroed at
allocation time.
Solution: Move the setup of the timer into corkscrew_setup().
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
This includes the new virtio crypto device, and fixes all over the
place. In particular enabling endian-ness checks for sparse builds
found some bugs which this fixes. And it appears that everyone is in
agreement that disabling endian-ness sparse checks shouldn't be
necessary any longer.
So this enables them for everyone, and drops __CHECK_ENDIAN__
and __bitwise__ APIs.
IRQ handling in virtio has been refactored somewhat, the
larger switch to IRQ_SHARED will have to wait as
it proved too aggressive.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYUxYEAAoJECgfDbjSjVRp5lgH/22HKRyb3+M+z3oH6R9rJmz5
T4y3XI4yDOTlh93VzxlrHjHNBnoWRvzV5hn6BKH6bTbSZ87TabNhfws11FKGvhER
G1ipl/DvwytvvWgZ5dFdcC4x/0wpWawt2jgpEpPP33VDVkGJFEEAGj6GX10ClX99
ggrNfzUCHOAFaIWzC29i7gYMnYHIJDUqK6ycDxZebzsE/c12SNRGASxei2D+6eYC
YkdVg0c/d7Wsk+ZO1ugiA6omO4UdvPAVvxUkvd4YphRikwEWH7gGuz558wiSo4VN
iEMZvyYXSEjx4B2Hg8+mH63zWROEpCmaToUix9+4AF7YhkaeX5fICNdkAPdtxc8=
=urXH
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio, vhost: new device, fixes, speedups
This includes the new virtio crypto device, and fixes all over the
place. In particular enabling endian-ness checks for sparse builds
found some bugs which this fixes. And it appears that everyone is in
agreement that disabling endian-ness sparse checks shouldn't be
necessary any longer.
So this enables them for everyone, and drops the __CHECK_ENDIAN__ and
__bitwise__ APIs.
IRQ handling in virtio has been refactored somewhat, the larger switch
to IRQ_SHARED will have to wait as it proved too aggressive"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits)
Makefile: drop -D__CHECK_ENDIAN__ from cflags
fs/logfs: drop __CHECK_ENDIAN__
Documentation/sparse: drop __CHECK_ENDIAN__
linux: drop __bitwise__ everywhere
checkpatch: replace __bitwise__ with __bitwise
Documentation/sparse: drop __bitwise__
tools: enable endian checks for all sparse builds
linux/types.h: enable endian checks for all sparse builds
virtio_mmio: Set dev.release() to avoid warning
vhost: remove unused feature bit
virtio_ring: fix description of virtqueue_get_buf
vhost/scsi: Remove unused but set variable
tools/virtio: use {READ,WRITE}_ONCE() in uaccess.h
vringh: kill off ACCESS_ONCE()
tools/virtio: fix READ_ONCE()
crypto: add virtio-crypto driver
vhost: cache used event for better performance
vsock: lookup and setup guest_cid inside vhost_vsock_lock
virtio_pci: split vp_try_to_find_vqs into INTx and MSI-X variants
virtio_pci: merge vp_free_vectors into vp_del_vqs
...
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
__bitwise__ used to mean "yes, please enable sparse checks
unconditionally", but now that we dropped __CHECK_ENDIAN__
__bitwise is exactly the same.
There aren't many users, replace it by __bitwise everywhere.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Akced-by: Lee Duncan <lduncan@suse.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
- Shared mlx5 updates with net stack (will drop out on merge if Dave's
tree has already been merged)
- Driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- Debug cleanups
- New connection rejection helpers
- SRP updates
- Various misc fixes
- New paravirt driver from vmware
-----BEGIN PGP SIGNATURE-----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=QeGy
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.
Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled
page:f6d09a00 count:0 mapcount:-127 mapping: (null)
index:0x0
flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:445!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP is at put_page_testzero.part.88+0xd/0xf
Call Trace:
[<c118a2cc>] __free_pages+0x3c/0x40
[<c118a30e>] free_pages+0x3e/0x50
[<c10222b4>] dma_generic_free_coherent+0x24/0x30
[<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140
[<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0
[<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
[<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
[<c13ed7a8>] pci_device_remove+0x38/0xb0
[<c14d3492>] __device_release_driver+0x72/0x100
[<c14d36b7>] driver_detach+0x97/0xa0
[<c14d29c0>] bus_remove_driver+0x40/0x80
[<c14d427a>] driver_unregister+0x2a/0x60
[<c13ec768>] pci_unregister_driver+0x18/0x70
[<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
[<c1101e78>] SyS_delete_module+0x158/0x210
[<c11b34f1>] ? __might_fault+0x41/0xa0
[<c11b353b>] ? __might_fault+0x8b/0xa0
[<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
[<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These are one-line functions that just call spin_lock/unlock_bh(); turn
them into static inlines to avoid the function call overhead.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reworks the ath9k driver to schedule transmissions to connected
stations in a way that enforces airtime fairness between them. It
accomplishes this by measuring the time spent transmitting to or
receiving from a station at TX and RX completion, and accounting this to
a per-station, per-QoS level airtime deficit. Then, an FQ-CoDel based
deficit scheduler is employed at packet dequeue time, to control which
station gets the next transmission opportunity.
Airtime fairness can significantly improve the efficiency of the network
when station rates vary. The following throughput values are from a
simple three-station test scenario, where two stations operate at the
highest HT20 rate, and one station at the lowest, and the scheduler is
employed at the access point:
Before / After
Fast station 1: 19.17 / 25.09 Mbps
Fast station 2: 19.83 / 25.21 Mbps
Slow station: 2.58 / 1.77 Mbps
Total: 41.58 / 52.07 Mbps
The benefit of airtime fairness goes up the more stations are present.
In a 30-station test with one station artificially limited to 1 Mbps,
we have seen aggregate throughput go from 2.14 to 17.76 Mbps.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ar9300_eeprom logic is already using only 8-bit (endian neutral),
__le16 and __le32 fields to state explicitly how the values should be
interpreted.
All other EEPROM implementations (4k, 9287 and def) were using u16 and
u32 fields with additional logic to swap the values (read from the
original EEPROM) so they match the current CPUs endianness.
The EEPROM format defaults to "all values are Little Endian", indicated
by the absence of the AR5416_EEPMISC_BIG_ENDIAN in the u8 EEPMISC
register. If we detect that the EEPROM indicates Big Endian mode
(AR5416_EEPMISC_BIG_ENDIAN is set in the EEPMISC register) then we'll
swap the values to convert them into Little Endian. This is done by
activating the EEPMISC based logic in ath9k_hw_nvram_swap_data even if
AH_NO_EEP_SWAP is set (this makes ath9k behave like the FreeBSD driver,
which also does not have a flag to enable swapping based on the
AR5416_EEPMISC_BIG_ENDIAN bit). Before this logic was only used to
enable swapping when "current CPU endianness != EEPROM endianness".
After changing all relevant fields to __le16 and __le32 sparse was used
to check that all code which reads any of these fields uses
le{16,32}_to_cpu.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are two ways of swapping the EEPROM data in the ath9k driver:
1) swab16 based on the first two EEPROM "magic" bytes (same for all
EEPROM formats)
2) field and EEPROM format specific swab16/swab32 (different for
eeprom_def, eeprom_4k and eeprom_9287)
The result of the first check was used to also enable the second swap.
This behavior seems incorrect, since the data may only be byte-swapped
(afterwards the data could be in the correct endianness).
Thus we introduce a separate check based on the "eepmisc" register
(which is part of the EEPROM data). When bit 0 is set, then the EEPROM
format specific values are in "big endian". This is also done by the
FreeBSD kernel, see [0] for example.
This allows us to parse EEPROMs with the "correct" magic bytes but
swapped EEPROM format specific values. These EEPROMs (mostly found in
lantiq and broadcom based big endian MIPS based devices) only worked
due to platform specific "hacks" which swapped the EEPROM so the
magic was inverted, which also enabled the format specific swapping.
With this patch the old behavior is still supported, but neither
recommended nor needed anymore.
[0]
50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The AR5416_VER_MASK macro does the same as get_eeprom_rev, except that
one has to know the actual EEPROM type (and providing a reference to
that in a variable named "eep"). Additionally the eeprom_*.c
implementations used the same shifting logic multiple times to get the
eeprom revision which was also unnecessary duplication of
get_eeprom_rev.
Also use the AR5416_EEP_VER_MINOR_MASK macro where needed and introduce
a similar macro (AR5416_EEP_VER_MAJOR_MASK) for the major version.
Finally drop AR9287_EEP_VER_MINOR_MASK since it simply duplicates the
already defined AR5416_EEP_VER_MINOR_MASK.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
get_eeprom(ah, EEP_MINOR_REV) and get_eeprom_rev(ah) are both doing the
same thing: returning the EEPROM revision (12 lowest bits). Make the
code consistent by using get_eeprom_rev(ah) everywhere.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows deciding if we have to swap the EEPROM data (so it matches
the system's native endianness) even if no byte-swapping (swab16, based on
the first two bytes in the EEPROM) is needed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The eepMisc field was not set explicitly. The default value of 0 means
that the values in the EEPROM (template) should be interpreted as little
endian. However, this is not clear until comparing the AR9003 code with
the other EEPROM formats.
To make the code easier to understand we explicitly state that the values
are little endian - there are no functional changes with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This replaces a magic number with a named #define. Additionally it
removes two "eeprom format" specific #defines for the "big endianness"
bit which are the same on all eeprom formats.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge more updates from Andrew Morton:
- a few misc things
- kexec updates
- DMA-mapping updates to better support networking DMA operations
- IPC updates
- various MM changes to improve DAX fault handling
- lots of radix-tree changes, mainly to the test suite. All leading up
to reimplementing the IDA/IDR code to be a wrapper layer over the
radix-tree. However the final trigger-pulling patch is held off for
4.11.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
radix tree test suite: delete unused rcupdate.c
radix tree test suite: add new tag check
radix-tree: ensure counts are initialised
radix tree test suite: cache recently freed objects
radix tree test suite: add some more functionality
idr: reduce the number of bits per level from 8 to 6
rxrpc: abstract away knowledge of IDR internals
tpm: use idr_find(), not idr_find_slowpath()
idr: add ida_is_empty
radix tree test suite: check multiorder iteration
radix-tree: fix replacement for multiorder entries
radix-tree: add radix_tree_split_preload()
radix-tree: add radix_tree_split
radix-tree: add radix_tree_join
radix-tree: delete radix_tree_range_tag_if_tagged()
radix-tree: delete radix_tree_locate_item()
radix-tree: improve multiorder iterators
btrfs: fix race in btrfs_free_dummy_fs_info()
radix-tree: improve dump output
radix-tree: make radix_tree_find_next_bit more useful
...
This cast is no longer needed.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
Link: http://lkml.kernel.org/r/20161110113616.76501.17072.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ARM architecture provides a mechanism for deferring cache line
invalidation in the case of map/unmap. This patch makes use of this
mechanism to avoid unnecessary synchronization.
A secondary effect of this change is that the portion of the page that
has been synchronized for use by the CPU should be writable and could be
passed up the stack (at least on ARM).
The last bit that occurred to me is that on architectures where the
sync_for_cpu call invalidates cache lines we were prefetching and then
invalidating the first 128 bytes of the packet. To avoid that I have
moved the sync up to before we perform the prefetch and allocate the
skbuff so that we can actually make use of it.
Link: http://lkml.kernel.org/r/20161110113611.76501.98897.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
T6 adapters reduce number of completions to host by generating single
completion for all the directly placed(DDP) iSCSI pdus in a sequence.
This patch adds new structure for completion hw cmd (struct
cpl_rx_iscsi_cmp) and implements T6 completion feature.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The recent introduction of qedr driver support in qede causes a GPF when probing the driver in a server without a RoCE enabled QLogic NIC. This fix avoids using an uninitialized pointer in such a case. Caught by the kernel test robot.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86:
ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’:
ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem here is that gcc won't track the state of the variable
across a spin_unlock. Moving the assignment out of the lock is
safe here and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver was
removed (got a "clean" driver for the same hardware through the netdev
tree), and some iio drivers were also dropped, but I think we ended up
adding a few thousand lines to the source tree in the end. Other than
that it's a lot of minor fixes all over the place, nothing major stands
out at all.
All of these have been in linux-next for a while. There will be a merge
conflict with Al's vfs tree in the lustre code, but the resolution for
that should be pretty simple, that too has been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAk1Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymikACg05b0h/iVTTH18474PXXnzw6jk9IAn0gI2fx9
cqp2MglTvphhrXzddL7V
=MeTw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver
was removed (got a "clean" driver for the same hardware through the
netdev tree), and some iio drivers were also dropped, but I think we
ended up adding a few thousand lines to the source tree in the end.
Other than that it's a lot of minor fixes all over the place, nothing
major stands out at all.
All of these have been in linux-next for a while. There will be a
merge conflict with Al's vfs tree in the lustre code, but the
resolution for that should be pretty simple, that too has been in
linux-next"
* tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits)
staging: comedi: comedidev.h: Document usage of 'detach' handler
staging: fsl-mc: remove unnecessary info prints from bus driver
staging: fsl-mc: add sysfs ABI doc
staging/lustre/o2iblnd: Fix misspelled attemps->attempts
staging/lustre/o2iblnd: Fix misspelling intialized->intialized
staging/lustre: Convert all bare unsigned to unsigned int
staging/lustre/socklnd: Fix whitespace problem
staging/lustre/o2iblnd: Add missing space
staging/lustre/lnetselftest: Fix potential integer overflow
staging: greybus: audio_module: remove redundant OOM message
staging: dgnc: Fix lines longer than 80 characters
staging: dgnc: fix blank line after '{' warnings.
staging/android: remove Sync Framework tasks from TODO
staging/lustre/osc: Revert erroneous list_for_each_entry_safe use
staging: slicoss: remove the staging driver
staging: lustre: libcfs: remove lnet upcall code
staging: lustre: remove set but unused variables
staging: lustre: osc: set lock data for readahead lock
staging: lustre: import: don't reconnect during connect interpret
staging: lustre: clio: remove mtime check in vvp_io_fault_start()
...
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer).
- Support for ARM Integrator/AP and Integrator/CP in the generic
DT cpufreq driver and elimination of the old Integrator cpufreq
driver (Linus Walleij).
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik).
- cpufreq core fix to eliminate races that may lead to using
inactive policy objects and related cleanups (Rafael Wysocki).
- cpufreq schedutil governor update to make it use SCHED_FIFO
kernel threads (instead of regular workqueues) for doing delayed
work (to reduce the response latency in some cases) and related
cleanups (Viresh Kumar).
- New cpufreq sysfs attribute for resetting statistics (Markus
Mayer).
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar).
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki).
- Support for per-logical-CPU P-state limits and the EPP/EPB
(Energy Performance Preference/Energy Performance Bias) knobs
in the intel_pstate driver (Srinivas Pandruvada).
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc).
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile
in the ACPI tables set to "mobile" (Srinivas Pandruvada).
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada).
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov).
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior).
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash).
- Idle injection rework (to make it use the regular idle path
instead of a home-grown custom one) and related powerclamp
thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek,
Sebastian Andrzej Siewior).
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc).
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior).
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla).
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki).
- Preliminary support for power domains including CPUs in the
generic power domains (genpd) framework and related DT bindings
(Lina Iyer).
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven).
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd).
- System sleep state selection interface rework to make it easier
to support suspend-to-idle as the default system suspend method
(Rafael Wysocki).
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren).
- Latency tolerance PM QoS framework imorovements (Andrew
Lutomirski).
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc).
- Intel RAPL power capping driver fixes, cleanups and switch over
to using the new CPU offline/online state machine (Jacob Pan,
Thomas Gleixner, Sebastian Andrzej Siewior).
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh
Kumar).
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf).
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu).
- Wakeup sources debugging enhancement (Xing Wei).
- rockchip-io AVS driver cleanup (Shawn Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vhxI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, cpufreq gets more changes than the other parts this time (one
new driver, one old driver less, a bunch of enhancements of the
existing code, new CPU IDs, fixes, cleanups)
There also are some changes in cpuidle (idle injection rework, a
couple of new CPU IDs, online/offline rework in intel_idle, fixes and
cleanups), in the generic power domains framework (mostly related to
supporting power domains containing CPUs), and in the Operating
Performance Points (OPP) library (mostly related to supporting devices
with multiple voltage regulators)
In addition to that, the system sleep state selection interface is
modified to make it easier for distributions with unchanged user space
to support suspend-to-idle as the default system suspend method, some
issues are fixed in the PM core, the latency tolerance PM QoS
framework is improved a bit, the Intel RAPL power capping driver is
cleaned up and there are some fixes and cleanups in the devfreq
subsystem
Specifics:
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer)
- Support for ARM Integrator/AP and Integrator/CP in the generic DT
cpufreq driver and elimination of the old Integrator cpufreq driver
(Linus Walleij)
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik)
- cpufreq core fix to eliminate races that may lead to using inactive
policy objects and related cleanups (Rafael Wysocki)
- cpufreq schedutil governor update to make it use SCHED_FIFO kernel
threads (instead of regular workqueues) for doing delayed work (to
reduce the response latency in some cases) and related cleanups
(Viresh Kumar)
- New cpufreq sysfs attribute for resetting statistics (Markus Mayer)
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar)
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki)
- Support for per-logical-CPU P-state limits and the EPP/EPB (Energy
Performance Preference/Energy Performance Bias) knobs in the
intel_pstate driver (Srinivas Pandruvada)
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc)
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile in
the ACPI tables set to "mobile" (Srinivas Pandruvada)
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada)
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov)
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior)
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash)
- Idle injection rework (to make it use the regular idle path instead
of a home-grown custom one) and related powerclamp thermal driver
updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej
Siewior)
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc)
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior)
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla)
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki)
- Preliminary support for power domains including CPUs in the generic
power domains (genpd) framework and related DT bindings (Lina Iyer)
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven)
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd)
- System sleep state selection interface rework to make it easier to
support suspend-to-idle as the default system suspend method
(Rafael Wysocki)
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren)
- Latency tolerance PM QoS framework imorovements (Andrew Lutomirski)
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc)
- Intel RAPL power capping driver fixes, cleanups and switch over to
using the new CPU offline/online state machine (Jacob Pan, Thomas
Gleixner, Sebastian Andrzej Siewior)
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar)
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf)
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu)
- Wakeup sources debugging enhancement (Xing Wei)
- rockchip-io AVS driver cleanup (Shawn Lin)"
* tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits)
devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks
devfreq: rk3399_dmc: Remove dangling rcu_read_unlock()
devfreq: exynos: Don't use OPP structures outside of RCU locks
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
PM / sleep: Print active wakeup sources when blocking on wakeup_count reads
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Domains: Fix compatible for domain idle state
PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators()
PM / OPP: Allow platform specific custom set_opp() callbacks
PM / OPP: Separate out _generic_set_opp()
PM / OPP: Add infrastructure to manage multiple regulators
PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage()
PM / OPP: Manage supply's voltage/current in a separate structure
PM / OPP: Don't use OPP structure outside of rcu protected section
PM / OPP: Reword binding supporting multiple regulators per device
PM / OPP: Fix incorrect cpu-supply property in binding
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
..
Commit 4490001029 ("virtio-net: enable
multiqueue by default") blindly set the affinity instead of queues
during probe which can cause a mismatch of #queues between guest and
host. This patch fixes it by setting queues.
Reported-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Fixes: 49000102901 ("virtio-net: enable multiqueue by default")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
* pm-core:
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Runtime: Defer resuming of the device in pm_runtime_force_resume()
PM / Runtime: Don't allow to suspend a device with an active child
net: smsc911x: Synchronize the runtime PM status during system suspend
PM / Runtime: Convert pm_runtime_set_suspended() to return an int
PM / Runtime: Clarify comment in rpm_resume() when resuming the parent
PM / Runtime: Remove the exported function pm_children_suspended()
* pm-qos:
PM / QoS: Export dev_pm_qos_update_user_latency_tolerance
PM / QoS: Fix writing 'auto' to pm_qos_latency_tolerance_us
PM / QoS: Improve sysfs pm_qos_latency_tolerance validation
* pm-avs:
PM / AVS: rockchip-io: make the log more consistent
In commit 02cea39586 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.
This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes: e3978673f5 ("drivers: net: xgene: Fix MSS programming")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The array for initializing the cle is set up on the stack with
almost entirely constant data and then passed to a function that
converts it into HW specific bit patterns. With the latest
addition, the size of this array has grown to the point that
we get a warning about potential stack overflow in allmodconfig
builds:
xgene_enet_cle.c: In function ‘xgene_enet_cle_init’:
xgene_enet_cle.c:836:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Looking a bit deeper at the usage, I noticed that the only modification
of the data is in dead code, as we don't even use the cle module
for phy_mode other than PHY_INTERFACE_MODE_XGMII. This means we
can simply mark the structure constant and access it directly rather
than passing the pointer down through another structure, making
the code more efficient at the same time as avoiding the
warning.
Fixes: a809701fed ("drivers: net: xgene: fix: RSS for non-TCP/UDP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit ARM with 64-bit dma_addr_t I get this warning about an
incorrect format string:
In file included from /git/arm-soc/drivers/net/ethernet/mellanox/mlx5/core/alloc.c:42:0:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c: In function ‘mlx5_frag_buf_alloc_node’:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c:134:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
We have the special %pad format for printing dma_addr_t, so use that
to print the correct address and avoid the warning.
Fixes: 1c1b522808 ("net/mlx5e: Implement Fragmented Work Queue (WQ)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhJeqETHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklam/vB/wNjAgeQO6HUAQrC1558EMHbJyBPtCG
yLJDyZcOQUmTBP0v9D0Fkg8LCjmEQaap9xGDoDVzhJp+qGVXkYu9IkLDDkulEkHN
UbKu/qcjSjccmjxD2J65CXphfFQxIIOEuahPuXN6wiK3s8zjaJkrPS9jcdKkgmQ2
3/NvLJtmgNJ6X8UhQ29aQtLvs635yQ7VxMj2LbYFIZ7BmtwDOBcFfk1crekKsfXW
oNpNWn8VWjOfPdvYGjfqAewmGCHt2zUIYV/GNKEd8cg4jTkhZAvKqi+QE0+tkta8
neNjn/hhi0nYOWz5iRLSYQMauVWzhMUlBrZ7R10926VKUWAzQGvBzZur
=HP5G
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-08
this is a pull request for one patch.
Jiho Chu found and fixed a use-after-free error in the cleanup path in
the peak pcan USB CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF error handling.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF timestamp.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF ethtool stats
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF vlan features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-08
I didn't miss your "net-next is closed" email, but it did come as a bit
of a surprise, and due to time-zone differences I didn't have a chance
to react to it until now. We would have had a couple of patches in
bluetooth-next that we'd still have wanted to get to 4.10.
Out of these the most critical one is the H7/CT2 patch for Bluetooth
Security Manager Protocol, something that couldn't be published before
the Bluetooth 5.0 specification went public (yesterday). If these really
can't go to net-next we'll likely be sending at least this patch through
bluetooth.git to net.git for rc1 inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LAN7801 MAC only support with phy fixup functions.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF receive data control path.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for freeing VF xmit buffers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for transmit functionality in VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF scatter gather lists.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for configuring mtu, multicast and mac address.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF link status related changes.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF link initialization and offload features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove first zero for add, and use full attribute name in comments.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9.
The issue commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use module_pci_driver() to get rid of some boilerplate code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two statements were not indented correctly so it's sort of
confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never set "slots" in this function.
Fixes: a9380b0f7b ("drivers: net: xgene: Add support for Jumbo frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.
This makes a slub problem, and it raise kernel oops with slub debugger
config.
Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
From firmware version 0.3 onwards we use the TX_ARET mode allowing for automatic
frame retransmissions. To actually make use of this feature we need to implement
the callback for setting the frame retries.
If the firmware version is to old print a warning and return with invalid value.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With version 0.3 the atusb firmware offers an interface to read a permanent
EUI64 address from the devices EEPROM. This patch checks if the firmware is
new enough and tries to read out and use the address. If this does not work
we fall back to the original randomly generated address.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The firmware versions will be used to enable selective features based on the
available firmware on the device. Make sure we do not need to fetch it for
every check but store it after the initial retrieval.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This file is shared between the atusb firmware and the kernel driver. In this
update it brings the new interfaces from version 0.3 of the firmware.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-07
This series contains updates to i40e and i40evf only.
Filip modifies the i40e to log link speed change and when the link is
brought up and down.
Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code. Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.
Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+. Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions. Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it. Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters. Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.
Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.
Henry fixes the "ethtool -p" function for 1G BaseT PHYs.
Carolyn adds support for 25G devices for i40e and i40evf.
Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.
v2: dropped last patch from previous series, since changes are needed based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 61e84623ac ("net: centralize net_device min/max MTU checking"),
the mtu range for dummy device becomes [68, 1500].
This patch extends it to [0, 65535].
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 61e84623ac ("net: centralize net_device min/max MTU checking"),
mtu range is checked at dev_set_mtu().
This patch adds min_mtu for nlmon device and remove unnecessary
ndo_change_mtu() function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e3aaf6494 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf6494 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When free macvlan_port in macvlan_port_destroy, it is safe to free
directly because netdev_rx_handler_unregister could enforce one
grace period.
So it is unnecessary to use kfree_rcu for macvlan_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.
So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.
phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.
[ 13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[ 13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[ 13.742115] Hardware name: Axis ARTPEC-6 Platform
[ 13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[ 13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[ 13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[ 13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[ 13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[ 13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[ 13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[ 13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[ 13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[ 13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[ 13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[ 13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[ 13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().
So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.
Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.
Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.
1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success. After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.
2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.
3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device(). A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.
4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.
5. 1 stats context is reserved when the RDMA driver registers. MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.
6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.
v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver register function with firmware consists of passing version
information and registering for async events. To support the RDMA driver,
the async events that we need to register may change. Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible. However, the
user can still increase network rings to the max if he wants. The actual
RDMA resources won't be reserved until the RDMA driver registers.
v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened. So we cannot do
function reset in bnxt_open() which will clear all the resources.
The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one(). This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.
Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode(). bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX. The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By refactoring existing code into this new function. The new function
will be used in subsequent patches.
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.
The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.
Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.
Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.
The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.
Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.
Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.
Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.
Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.
Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.
Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.
This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.
The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.
Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous code refactors have accidentally caused issues with the
counting of active_filters. Avoid similar issues in the future by simply
re-counting the active filters every time after we handle add and delete
of all the filters. Additionally this allows us to simplify the check
for when we exit promiscuous mode since we can combine the check for
failed filters at the same time.
Additionally since we recount filters at the end we need to set
vsi->promisc_threshold as well.
The resulting code takes a bit longer since we do have to loop over
filters again. However, the result is more readable and less likely to
become incorrect due to failed accounting of filters in the future.
Finally, this ensures that it is not possible for vsi->active_filters to
ever underflow since we never decrement it.
Change-ID: Ib4f3a377e60eb1fa6c91ea86cc02238c08edd102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The service task lock was being set in the scheduling function, not the
actual service task. This would potentially leave the bit set for a long
time before the task actually ran. Furthermore, if the service task
takes too long, it calls the schedule function to reschedule itself -
which would fail to take the lock and do nothing.
Instead, set and clear the lock bit in the service task itself. In the
process, get rid of the i40e_service_event_complete() function, which is
really just two lines of code that can be put right in the service task
itself.
Change-ID: I83155e682b686121e2897f4429eb7d3f7c669168
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on external PHY type, register access method should be
different. Clause22 or Clause45 can be chosen for different PHYs.
Implemented functions apply correct access method for used device.
Change-ID: If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds adminq support for Forward Error
Correction ("FEC")for 25g products.
Change-ID: Iaff4910737c239d2c730e5c22a313ce9c37d3964
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for 25G devices - defines and data structures.
One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.
This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.
Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the %d specifier used for printing vsi->active_filters and
vsi->promisc_threshold with an unsigned %u format specifier. While it is
unlikely in practice that these values will ever reach such a large
number they are unsigned values and thus should not be interpreted as
negative numbers.
Change-ID: Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before this patch "ethtool -p" was not blinking the LEDs on boards
with 1G BaseT PHYs.
This commit identifies 1G BaseT boards as having the LEDs connected
to the MAC. Also, renamed the flag to be more descriptive of usage.
The flag is now I40E_FLAG_PHY_CONTROLS_LEDS.
Change-ID: I4eb741da9780da7849ddf2dc4c0cb27ffa42a801
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netdev->dev_addr MAC filter already exists in the
MAC/VLAN hash table, as it is added when we configure
the netdev in i40e_configure_netdev. Because we already
know that this address will be updated in the
hash_for_each loops, we do not need to handle it
specially. This removes duplicate code and simplifies
the i40e_vsi_add_vlan and i40e_vsi_kill_vlan functions.
Because we know these filters must be part of the
MAC/VLAN hash table, this should not have any functional
impact on what filters are included and is merely a code
simplification.
Change-ID: I5e648302dbdd7cc29efc6d203b7019c11f0b5705
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function i40e_napi-poll() returns 0 when it clean completely
the Rx rings, but this foul budget accounting in core code.
Fix this by returning the actual work done, capped to budget - 1, since
the core doesn't allow to return the full budget when the driver modifies
the NAPI status
This is based on a similar change that was made for the ixgbe driver by
Paolo Abeni.
Change-ID: Ic3d93ad2fa2fc8ce3164bc461e69367da0f9173b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit 53cb6e9e89 ("i40e: Removal of workaround for simple
MAC address filter deletion") removed a workaround for some
firmware versions which was reported to not be necessary in production
NICs. Unfortunately this workaround is necessary in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+ (8086:1583).
Without this patch, the mentioned NICs with current firmware exhibit
issues when adding VLANs, as outlined by the following reproduction:
$modprobe i40e
$ip link set <device> up
$ip link add link <device> vlan100 type vlan id 100
$dmesg | tail
<snip>
kernel: i40e 0000:82:00.0: Error I40E_AQ_RC_EINVAL adding RX
filters on PF, promiscuous mode forced on
This results in filters being marked as FAILED and setting the device in
promiscuous mode.
The root cause of receiving the -EINVAL error response appears to be due
to a conflict with the default MAC filter which still exists on the
default firmware for this device. Attempting to add a new VLAN filter on
the default MAC address conflicts with the IGNORE_VLAN setting on the
default rule.
Change-ID: I4d8f6d48ac5f60cfe981b3baad30eb4d7c170d61
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_txd_use_count function was fast but confusing. In the comments,
it even admits that it's ugly. So replace it with a new function that is
(very) slightly faster and has extensive commenting to help the thicker
among us (including the author, who will forget in a week) understand
how it works.
Change-ID: Ifb533f13786a0bf39cb29f77969a5be2c83d9a87
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes the driver log link speed change. Before applying the
patch link messages were printed only on state change. Now message is
printed when link is brought up or down and when speed changes.
Change-ID: Ifbee14b4b16c24967450b3cecac6e8351dcc8f74
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes tun.c to call netif_receive_skb instead of netif_rx
when a packet is received (if CONFIG_4KSTACKS is not enabled to avoid
stack exhaustion). The difference between the two is that netif_rx queues
the packet into the backlog, and netif_receive_skb proccesses the packet
in the current context.
This patch is required for syzkaller [1] to collect coverage from packet
receive paths, when a packet being received through tun (syzkaller collects
coverage per process in the process context).
As mentioned by Eric this change also speeds up tun/tap. As measured by
Peter it speeds up his closed-loop single-stream tap/OVS benchmark by
about 23%, from 700k packets/second to 867k packets/second.
A similar patch was introduced back in 2010 [2, 3], but the author found
out that the patch doesn't help with the task he had in mind (for cgroups
to shape network traffic based on the original process) and decided not to
go further with it. The main concern back then was about possible stack
exhaustion with 4K stacks.
[1] https://github.com/google/syzkaller
[2] https://www.spinics.net/lists/netdev/thrd440.html#130570
[3] https://www.spinics.net/lists/netdev/msg130570.html
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more common logging style, standardize function output logging use.
Miscellanea:
o Add and use pr_fmt
o Convert printks to pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten function declaration and definition arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add braces where appropriate and remove an unnecessary else.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spaces around operators.
git diff -w shows no differences.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove leading and trailing whitespace.
git diff -w shows no differences.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the RX checksum function to check the
status of the hardware calculated checksum and its error and
appropriately convey status to the upper stack in skb->ip_summed
field.
In hardware, we only support checksum for the following
protocols:
1) IPv4,
2) TCP(over IPv4 or IPv6),
3) UDP(over IPv4 or IPv6),
4) SCTP(over IPv4 or IPv6)
but we support many L3(IPv4, IPv6, MPLS, PPPoE etc) and
L4(TCP, UDP, GRE, SCTP, IGMP, ICMP etc.) protocols.
Hardware limitation:
Our present hardware RX Descriptor lacks L3/L4 checksum
"Status & Error" bit (which usually can be used to indicate whether
checksum was calculated by the hardware and if there was any error
encountered during checksum calculation).
Software workaround:
We do get info within the RX descriptor about the kind of
L3/L4 protocol coming in the packet and the error status. These
errors might not just be checksum errors but could be related to
version, length of IPv4, UDP, TCP etc.
Because there is no-way of knowing if it is a L3/L4 error due
to bad checksum or any other L3/L4 error, we will not (cannot)
convey hardware checksum status(CHECKSUM_UNNECESSARY) for such
cases to upper stack and will not maintain the RX L3/L4 checksum
counters as well.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
