Add nodes for USB and related PHYs.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds a reference to the dts of the Raspberry Pi 3 A+,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Add the fsl,magic-packet property in the fec node.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Populate the fec1 node with the missing MDIO and PHY entries.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It enables USB3 host device support for imx8mq-evk board.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the am654x-evm, sdhci0 node is connected to an eMMC. Add node and
pinmux for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add support for the Secure Digital Host Controller Interface (SDHCI)
present on TI's AM654 SOCs. It is compatible with eMMC5.1 Host
Specifications.
Enable only upto HS200 speed mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The GPCv2 sits between most of the peripherals and the GIC and
functions as a wakeup controller for the CPU cores.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Flash mt35xu512aba connected to FlexSPI controller supports
1-1-8/1-8-8 protocol.
Added flag spi-rx-bus-width and spi-tx-bus-width with values as
8 and 8 respectively for both flashes connected at CS0 and CS1.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The boot from eMMC is currently broken on the NXP i.MX8MQ EVK board.
When trying to boot from eMMC it fails with:
...
[ 1.271938] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.287429] print_req_error: I/O error, dev mmcblk1, sector 1 flags 0
[ 1.306833] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.322325] print_req_error: I/O error, dev mmcblk1, sector 2 flags 0
[ 1.329559] Buffer I/O error on dev mmcblk1, logical block 0, async page read
[ 1.336714] mmcblk1: unable to read partition table
...
The problem is the result of a partial misconfiguration of the pins and
the missing assigned clock rate.
Fixes: 9079aca4aa ("arm64: add support for i.MX8M EVK board")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree support for Oxalis SoM board from EBS-SYSTART. This
board is one of the 96Boards Enterprise Edition platform. Below are some
of the key features of this board:
* SoC: NXP Layerscape LS1012A
* RAM: 1GB DDR3L
* PMU: NXP VR5100
* Storage: 64MByte SPI Flash for bootloader and RCW, MicroSD Card, SATA
* Connectivity: 2x Ethernet
* USB: 2x USB3.0
More information about this board can be found in 96Boards product
page: https://www.96boards.org/product/oxalis/
Ethernet and SPI flash are not supported yet!
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fspi node property for LX2160A SoC for FlexSPI driver.
Property added for the FlexSPI controller and for the connected
slave device for the LX2160ARDB target.
This is having two SPI-NOR flash device, mt35xu512aba, connected
at CS0 and CS1.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDcard detection of hikey960 is active low so cd-inverted is wrong.
Instead of adding cd-inverted, we should better set correctly cd-gpios
to use GPIO_ACTIVE_LOW.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Support for Fixed Virtual Platforms(FVP) Base RevC model to enable
development of software around the new features available
2. Addition of dynamic-power-coefficient information for CPUs on Juno
3. Miscellaneous changes like re-ordering device nodes, using existing
macros for GIC flags in interrupt-maps and using list instead of
tuple(which is wrong but works as number of interrupt cells is 1)
for mmci interrupts
-----BEGIN PGP SIGNATURE-----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=UqJG
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/fast models updates for v5.1
1. Support for Fixed Virtual Platforms(FVP) Base RevC model to enable
development of software around the new features available
2. Addition of dynamic-power-coefficient information for CPUs on Juno
3. Miscellaneous changes like re-ordering device nodes, using existing
macros for GIC flags in interrupt-maps and using list instead of
tuple(which is wrong but works as number of interrupt cells is 1)
for mmci interrupts
* tag 'juno-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add cpu dynamic-power-coefficient information
arm64: dts: fast models: Add DTS fo Base RevC FVP
arm64: dts: juno/fast models: sort couple of device nodes
arm64: dts: models: use list instead of tuple for mmci interrupts
arm64: dts: juno/fast models: using GIC macros instead of hardcoded values
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
-----BEGIN PGP SIGNATURE-----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=kZwf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT64 changes for 5.1
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
* tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable A64 timer workaround
arm64: dts: allwinner: a64: Fix a typo
arm64: dts: allwinner: a64: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
-----BEGIN PGP SIGNATURE-----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=4km1
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 Fixes for 5.0-rc3
* Fix irq controller compatible for the MSM8996 platforms
* tag 'qcom-fixes-for-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: add msm8996 compatible to gicv3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Second Round of Renesas ARM Based SoC Fixes for v5.0
Enable DMA for SCIF2 on R-Car M3-W (r8a7796) and M3-n (r8a77965), and
(RZ/G2M) r8a774a1 SoCs.
This is was omitted from patches enabling DMA for other SCIF devices on the
same SoCs due to missing documentation. However, it is regarded as a fix
as arguably those patches claim to add this feature.
Per-SoC patches are provided to ease backporting of this fix as the kernel
version to be fixed is different for each SoC.
* tag 'renesas-fixes2-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A CPUfreq driver, like the scpi driver used on Juno boards, which
provide the Energy Model with power cost information via the PM_OPP
of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Since DVFS is broken on Juno r1, no dynamic-power-coefficient
information has been added to its dts file.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixed Virtual Platforms(FVP) Base RevC model is an emulated Arm platform
with GICv3, PCIe, SMMUv3 and various other features. These are available
free of charge on the Arm Community website at Arm Development
Platforms[1].
It resembles the Foundation Platform, which is a simple FVP that
includes an Armv8‑A AEM processor model but this has two cluster of four
cores, a CCI-550 interconnect, an SMMU and two PCI devices.
In order to enable development of software, let's add a description of
the Revison C version of Base platform.
The documentation for this FVP model is available @[2] for reference.
[1] https://community.arm.com/dev-platforms/
[2] https://static.docs.arm.com/100966/1104/fast_models_fvp_rg_100966_1104_00_en.pdf
Cc: Vincent Stehlé <vincent.stehle@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
[sudeep.holla: aligned interrupt-map with other DTS, added SPE, changed
PMU to use GIC PPI, moved to PSCI v0.2, commit log rewording]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Sort the couple device nodes with unit addresses which are out of order.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
RTSM/FVP vexpress motherboard model MMCI requires dedicated interrupts
for CMD and PIO, which obviously should be expressed as a list. Current
form uses tuple and it works fine since interrupt-cells equal to 1.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
There are macros that exist to indicate the GIC specific flags and
custom cell values as per the GIC DT bindings. It's used in most of the
places in these DTS files but not all. To maintain consistency, lets
use the macros at all the places.
Since DTC doesn't even warn is any cells are missing, it's very hard to
debug if that's the case. Changing to use macros avoids missing cells/
columns.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a node for H6 SRAM C1 section.
Manual calls it VE SRAM, but for consistency with older SoCs, SRAM C1
name is used.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add dts node details for Allwinner A64 CSI controller.
A64 CSI has similar features as like in H3, but the CSI_SCLK
need to update it to 300MHz than default clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GIC device node was placed out of order in the initial device tree
submission. Move it so the nodes are correctly sorted by base address
again.
Fixes: e54be32d02 ("arm64: allwinner: h6: add the basical Allwinner H6 DTSI file")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After commit ef05bcb60c, boot from USB drives is broken.
Fix this problem by enabling usb-host regulators during boot time.
Fixes: ef05bcb60c ("arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Voytik <voytikd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Ports are described by child 'port' nodes contained in the device node.
'ports' is optional and is used to group all 'port' nodes which is not
the case here.
This patch fixes the following warnings:
arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts:25.9-29.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts:46.9-50.5: Warningi (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts:94.9-98.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
At some point during rebases these were shuffled around. Put them in the
right order again (sorted by unit-address).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653 ("arm64: zynqmp: Add support for Xilinx zcu100-revC")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add regulators to the Tegra210 Darcy DTS file including support for
the MAX77620 PMIC.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add initial device-tree support for NVIDIA Shield TV (a.k.a. Darcy)
based upon Tegra210 SoC with 3 GiB of LPDDR4 RAM.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of hardcoding the value (0), reuse the symbolic name from
dt-bindings/interrupt-controller/arm-gic.h.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix IRQ type of PMIC which should be configured as high-level trigger.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the register range of apbmisc, that originally inherited from
Tegra124.
Reported-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
gpio-keys,name is not a valid property supported by gpio-keys
driver so remove it from DTS.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Define all six QUP controllers, both as SPI and I2C, allowing boards to
enable these as needed. Associated pinmux states are also defined, to
require only pinconf states to be specified by the boards, as they are
enabled.
Note that SPI has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the BLSP2 BAM and add the remaining four UARTs found on the QCS404
platform.
Note that these has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
BLSP1 UART2 is used as debug uart on the EVB development board, define
pinmux state for the UART in the platform dtsi and pinconf state for it
in the board dts.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fix up the lpasscc address and size, missed during the conversion to
address- and size-cells of 2.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the duplicate inclusion of qcom,gcc-sdm845.h
mistakenly introduced by commit 6e17f81405 ("arm64:
dts: sdm845: add prng-ee node").
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
[bjorn: Also fix sort order of lpasscc include, while we're there]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add reserve-memory nodes for mpss and mba required for
remoteproc mss pil.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the gpio-ranges property to the TLMM node so that GPIO hogs work.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
For devices attached to an IOMMU, translation between IOVA and physical
addresses is no longer 1:1 and dma-ranges should be specified to
describe the available IOVA address space.
On SDM845 the busses are implemented with 36 address bits, so dma-ranges
must be defined to reduce the size of the IOVA address space from the 48
bits supported by the SMMU. Without this DMA allocations may end up with
IOVAs outside the valid range, that gets truncated by the bus between
the device and its translation unit.
Also extend ranges to describe the available address space.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The busses on SDM845 provides 36 address bits, extend the address and
size cells to make it possible to describe this in "ranges" and
"dma-ranges".
While touching all reg properties, addresses are padded to 8 digits.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on SDM845 soc.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the node to support PDC Global reset driver on
SDM845 SoCs
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Correct address for pcs_misc register region of USB3 QMP UNI PHY.
These registers are used during runtime-suspend/resume routines
of phy.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: ca4db2b538 ("arm64: dts: qcom: sdm845: Add USB-related nodes")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the low pass audio clock controller node to sdm845 based on
the example in the bindings.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[bjorn: Disabled lpasscc node, as it's normally protected]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the video clock controller node to sdm845 based on the examples
in the bindings.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the GPU clock controller nodes as per the example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Quad SPI controller to the main sdm845 device tree file.
Boards will be expected to assign the proper pinctrl depending on how
many chip selects they have hooked up and how many data lines.
This depends on commit 48735597f7 ("clk: qcom: Add qspi (Quad SPI)
clock defines for sdm845 to header") to add the needed defines. It
also shouldn't land until the patch ("dt-bindings: spi: Qualcomm Quad
SPI(QSPI) documentation") [1] lands.
[1] https://lkml.kernel.org/r/20181002214709.162330-1-ryandcase@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
msm8998 has a dozen i2c controllers which can be used to connect to board
specific peripherals. Enumerate the controllers so that boards can wire
up as needed.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[bjorn: Renumbered labels on BLSP2 nodes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
l21 is used as sdcard vmmc, and needs the load increased to prevent
voltage drop issues with some sdcards. This addresses -84 errors seen
during sdcard init with SDR104 cards.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DPU is short for the Display Processing Unit. It is the display
controller on Qualcomm SDM845 chips.
This change adds MDSS and DSI nodes to enable display on the
target device.
Changes in v2:
- Beefed up commit message
- Use SoC specific compatibles for mdss and dpu (Rob H)
- Use assigned-clocks to set initial clock frequency(Rob H)
Changes in v3:
- added IOMMU node
- Fix device naming (remove _phys)
- Use correct IRQ_TYPE in interrupt specifiers
Changes in v4:
- move mdss node to preserve the unit address sort order
- remove _clk suffix from dsi clocks
(both the comments are from Doug Anderson)
Changes in v5:
- Keep the device status "disabled" by default (Bjorn Andersson)
- Use MDSS_GDSC macro (Jordan)
- Fix phy-names (Jordan)
- List reg ranges in numerical order (Jordan)
Changes in v6:
- Separating this patch out of the series
- fix phy-names
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As instability in the architectural timer has been observed on multiple
devices using this SoC, inluding the Pine64 and the Orange Pi Win,
enable the workaround in the SoC's device tree.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch adds ethernet support to the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pincontrol support to scif2.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Si-Linux board based on RZ/G2E:
- Memory,
- Main crystal,
- Serial console
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS400 of SDHI3 using the corresponding DT property.
No further changes are required.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
SCIF2 on R-Car E3 can be used with both DMAC1 and DMAC2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on RZ/G2E can be used with both DMAC1 and DMAC2.
Fixes: 1b24f9e8ea3ff95f ("arm64: dts: renesas: r8a774c0: Add SCIF and HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There are two regulator1 nodes in the Ebisu DTS right now, one 3.3V for
the eMMC and one 12V for the backlight. This causes one to be overwritten
by the other, ultimatelly resulting in inoperable eMMC, which depends on
the former. Fix this by renumbering the backlight regulator to regulator2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 9d16c4a10e ("arm64: dts: renesas: r8a77990: ebisu: Add backlight")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the V3M Starter Kit board's device tree, now
that we have the GPIO support (previously phylib had to resort to polling).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Ebisu board is using simple-scu-audio-card
which is used for Sampling Rate Convert, or MIXer, etc.
But, Ebisu is not using such feature.
Then, simple-audio-card is very enough.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Before, BUSIF which is needed for DMA transfer was automatically handled
via SSI, but it cared BUSIF0 only.
Now, rsnd driver can handle BUSIF0-7 (= for Gen3) BUSIF0-3 (= for Gen2)
via SSIU, and it is keeping compatibility.
Thus, BUSIF0 settings via SSI had been kept to avoid git merge timing
issue / git bisect issue, but it is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Before, BUSIF which is needed for DMA transfer was automatically handled
via SSI, but it cared BUSIF0 only.
Now, rsnd driver can handle BUSIF0-7 (= for Gen3) BUSIF0-3 (= for Gen2)
via SSIU, and it is keeping compatibility.
Thus, BUSIF0 settings via SSI had been kept to avoid git merge timing
issue / git bisect issue, but it is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
KingFisher has pcm3168 sound codec. This patch enables it.
Because pcm3168 can't handle symmetric channel on playback/
capture, we need to handle it as different DAI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing ULCB HDMI sound support.
To use sound card, HDMI video is mandatory.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ULCB can use daughter board which is called as KingFisher.
It has extra sound interface, thus we want to use it.
But, basically, ALSA SoC can't use Multiple sound card with single
CPU sound interface (= SSI). Thus we need to use Single Sound Card
with multiple DAI interface.
To be easy to expand ULCB sound card on KingFisher, it is better to
use multi-dai-link style sound card on ULCB sound DT.
Now, "simple-audio-card" / "audio-graph-card" both can support
multi-dai-link style, but HDMI sound support (which is not yet supported
on ULCB) needs "audio-graph-card".
Using audio-graph-card is better selection.
This patch exchange current sound card to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 6d2ca85279 ("dt-bindings: display: renesas: Deprecate
LVDS support in the DU bindings"), the internal LVDS encoder has DT
bindings separate from the DU. The device trees for all R-Car H3 and
M3-W development boards were ported over to the new model, but
Salvator-XS boards equipped with an R-Car M3-W SoC were forgotten.
Fixes: 58e8ed2ee9 ("arm64: dts: renesas: Convert to new LVDS DT bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the i2c nodes so that sub-nodes of the soc node are sorted by bus
address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the pciec0 node so that sub-nodes of the soc node are
sorted by bus address.
This change has no run-time affect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for VIN4, VIN5 and CSI40 to RZ/G2E (a.k.a. R8A774C0)
SoC specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PCI express channel 0 device tree node to the
RZ/G2E (a.k.a. R8A774C0) SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the RZ/G2E Audio-DMAC device to IPMMU-MP as stated by the
RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the RZ/G2E AVB device to IPMMU-DS0 as stated by the
RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1, and SYS-DMAC2 to IPMMU-DS0 and
IPMMU-DS1, according to what reported by the RZ/G2 User's manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb3.0 host and function device nodes to the RZ/G2E SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The RZ/G2E (a.k.a. R8A774C0) has one RGB output and two LVDS
outputs connected to DU.
This patch add support for DU, LVDS encoders, VSP and FCP.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add PWM support to the RZ/G2E (a.k.a. R8A774C0) SoC specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G2E SoC (a.k.a. R8A774C0).
This work is based on similar work done on the R8A77990 SoC
by Yoshihiro Kaneko <ykaneko0929@gmail.com>.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers on RZ/G2E SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the thermal device node and the thermal-zones
node to the SoC specific dtsi for the RZ/G2E.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for both RZ/G2E CAN channels.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-7] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774c0 device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a774c0 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
RZ/G2E (a.k.a r8a774c0) SoC, and adjust the interrupt delivery masks
for the ARM Generic Interrupt Controller and Architectured Timer.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog support to the RZ/G2E (a.k.a. R8A774C0) SoC
specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO device nodes to the DT of the r8a774c0 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add PFC support to the RZ/G2E (a.k.a. r8a774c0) SoC specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2E.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2E SCIF and HSCIF serial ports,
including clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G2E SoC (a.k.a. r8a774c0).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode doesn't support
on R-Car E3. This patch fixes EthernetAVB phy mode to rgmii.
This is achieved by simply dropping the phy-mode property from
r8a77990-ebisu.dts as the default property for this for r8a77990,
as set in r8a77990.dtsi, is "rgmii".
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Limiting the HS200 rate on the s400 was just a way to mask that the
tuning setting were not correct. This seems to have been fixed with
the recent MMC driver update. We can now use HS200 at full speed.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The bcm wifi/bt device on SDIO support SDR104 and it seems to work
well following the recent mmc driver update, so enable this
ultra high speed mode
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SimpleFB allows transferring a framebuffer from the firmware/bootloader
to the kernel, while making sure the related clocks and power supplies
stay enabled.
Add nodes for CVBS and HDMI Simple Framebuffers.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Allows the vpu driver to optionally use a canvas provider node.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For whatever reason, the sdmmc_dectn function isn't working properly
as-is, and microSD insertion and removal goes unnoticed. Using the pin
as a GPIO interrupt instead is rather noisy without any debouncing, but
is good enough to make it useful until someone feels inclined to figure
out how the vendor kernel/firmware gets the dedicated function to work
with no obvious difference in the pinmux/GRF configuration. Let's also
take the opportunity to tweak the node name so that all related pins
end up grouped together in the compiled DTB.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In common with most Rockchip reference designs, NanoPC-T4 has a passive
IR receiver connected to PWM3. In lieu of a specialised driver for
PWM-based IR pulse measurement, running the pin as a GPIO with the basic
driver works perfectly well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The nanopi4 boards differ primarily in their power trees, with the main
5V and 3.3V rails having very different topologies on the smaller USB-C
powered boards vs. the 12V-powered T4, as well as minor variation in
other regulators related to various external connectors.
Additionally, the recovery key is only present on the T4 - ADC_IN1 is
simply pulled high and not exposed on the other boards - and the lowest
common denominator for MMC speed is actually HS200 according to the
vendor DTs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are a number of subtle differences between the nanopi4 variants,
and where they disagree, the common DTSI currently follows the details
of NanoPi M4. In order to improve matters even more, let's add a
separate DTS for the M4 to which we can start splitting things out
appropriately. The third variant, NanoPi NEO4, is a lot closer to the M4
than either is to the larger T4, so arguably could get away with just
sharing the M4 DT for now (plus I have neither of the smaller boards to
actually test with).
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SCIF2 on R-Car M3-N can be used with both DMAC1 and DMAC2.
Fixes: 0ea5b2fd38 ("arm64: dts: renesas: r8a77965: Add SCIF device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on R-Car M3-W can be used with both DMAC1 and DMAC2.
Fixes: dbcae5ea4b ("arm64: dts: r8a7796: Enable SCIF DMA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIF2 on RZ/G2M can be used with both DMAC1 and DMAC2.
Fixes: 3a3933a4fa ("arm64: dts: renesas: r8a774a1: Add SCIF and HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds support for the power domain controller found on the
i.MX8MQ SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We can reuse the pwm from fsl,imx27-pwm as with other imx SOCs.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This typo inverted the meaning of the comment, but the rest of the
comment and the code reveal that the regulator in question needs to be
on at all times.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
gpiio5 is missspelt in msm8996-pins.dtsi, fix that.
Signed-off-by: Jakob Wuhrer <jakobwuhrer@airmail.cc>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In the same way as for msm8974-hammerhead, l11 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Tested on Dragonboard-410c and DART-SD410 boards.
Fixes: 4c7d53d16d (arm64: dts: apq8016-sbc: add regulators support)
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The PMS405 PMIC has an ADC that exposes the on-die temperature that we
wire up to spmi-temp-alarm thermal driver. This allows the PMIC
temperature to be exposed to Linux through the thermal framework.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on qcs404 soc.
Optional clock and regulator controls are not yet available in
upstream, hence add them once available.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The controller can support EXT_CSD_CARD_TYPE_HS400_1_8V cards.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This change adds the cpufreq node as per the bindings example for SDM845.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the second lane registers for the USB PHY, now that the
QMP phy bindings have been updated. This way the driver can stop
reaching beyond its register region to get at the second lane.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the UFS host controller and PHY on sdm845-mtp.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the UFS controller and PHY to SDM845.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add iommu context for the host controller]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for arm,mmu-500 available on sdm845.
This MMU-500 with single TCU and multiple TBU architecture
is shared among all the peripherals except gpu.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable support for one of the micro SD slots on the MTP.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add one of the two SD controllers to SDM845.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
ROCK Pi 4 is RK3399 based SBC from radxa.com. board has a 1G/2G/4G lpddr4, CSI,
DSI, HDMI, OTG, USB 2.0, USB 3.0, 10/100/1000 RGMII Ethernet Phy, es8316 codec,
POE, WIFI (for Model B only), PCIE M.2 support on board.
This patch enables
- HDMI Display
- Console
- MMC, EMMC
- USB 2.0, USB-3.0
- Ethernet
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Pragnesh Patel <Pragnesh_Patel@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add this property to all layerscape platforms to improve USB read write performance.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the UARTs by defaultto avoid registering unused UARTs. This
effectively change the number of registered UARTS for the RDB and QDS from
4 to 2 but this seems the right thing to do.
It is especially useful when connecting other 8250 uart on PCIe for example
as the default maximum number of 8250 UARTs that can be registered is 4.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set the Integrated Flash Controller status to disabled so each board has
the option to enable it. All the existing users have status = "okay" so
there is no functional change.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a generic node name for the m25p80 flashes on ls1043 and ls1046 boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch also adds the iommu-map property in fsl-mc node, so
that fsl-mc can use iommu.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add num-viewport property for PCIe DT nodes to specify how many
viewports are implemented.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The were added at the end of the AIPS1 address space, while they
are in fact in the middle.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable spdif input device on the S400 and add it to the card
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SPDIF capture codec to the axg s400 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SPDIF input device of the axg audio subsystem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds a device tree for the NanoPC-T4 SBC, which is based on the
Rockchip RK3399 SoC and marketed by FriendlyELEC.
Known working:
- Serial
- Ethernet
- HDMI
- USB 2.0
All of the interesting stuff is in a .dtsi because there are at least
two other boards that share most of it: NanoPi M4 and NanoPi NEO4.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[rm: various further cleanup]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MPP52 signal is on the seconds GPIO instance of CP0, which
corresponds to the &cp0_gpio2 handle.
Rename the property name to the standard '-gpios' suffix while at it.
Fixes: b83e1669ad ("arm64: dts: marvell: mcbin: add support for PCIe")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from Linux leads to an immediate crash.
So let's make the same memory reservation as the vendor kernel.
[gregory: added as comment that this region matches the mainline U-boot]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f91 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pinmux support for UART1 on MediatekX20 Development board based
on Mediatek MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Now there are device tree clocks for the ARM64 SMMU,
add SMMU support to the Stratix10 Device Tree which
includes adding the SMMU node and adding IOMMU stream
ids to the SMMU peripherals.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The backlight levels provided in the Draak DT produce a perceived
brightness very biased towards high brightness. Use better brightness
levels based on the CIE 1931 formula.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the backlight device for the LVDS1 output, in preparation for panel
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When introducing the video-codec node for the video engine, the
compatible for the H5 was used instead of the compatible for the
A64. Use the right compatible instead.
Fixes: d60ce24740 ("arm64: dts: allwinner: a64: Add Video Engine node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on Teres I Laptop.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Rock64 boards has analog audio jack on it. RK3328 can output
analog audio signal using I2S1 and ACODEC core.
This patch adds sound node for analog audio for Rock64.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3328 i2s and spdif controllers only ever have one output
connection, so as with all implementations of the rk3066 i2s
controllers we can keep the #sound-dai-cells in the main dtsi
instead of having it repeated in each board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds audio codec (ACODEC) node that converts to analog
audio signal from I2S for rk3328.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
