In mlx5e_configure_flower() flow pointer is protected by rcu read lock.
However, after cited commit the pointer is being used outside of rcu read
block. Extend the block to protect all pointer accesses.
Fixes: 553f932838 ("net/mlx5e: Support tc block sharing for representors")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix eeprom SFP query support by setting i2c_addr, offset and page number
correctly. Unlike QSFP modules, SFP eeprom params are as follow:
- i2c_addr is 0x50 for offset 0 - 255 and 0x51 for offset 256 - 511.
- Page number is always zero.
- Page offset is always relative to zero.
As part of eeprom query, query the module ID (SFP / QSFP*) via helper
function to set the params accordingly.
In addition, change mlx5_qsfp_eeprom_page() input type to be u16 to avoid
unnecessary casting.
Fixes: a708fb7b1f ("net/mlx5e: ethtool, Add support for EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
NVM config file address will be modified when the MBI image is upgraded.
Driver would return stale config values if user reads the nvm-config
(via ethtool -d) in this state. The fix is to re-populate nvm attribute
info while reading the nvm config values/partition.
Changes from previous version:
-------------------------------
v3: Corrected the formatting in 'Fixes' tag.
v2: Added 'Fixes' tag.
Fixes: 1ac4329a1c ("qed: Add configuration information to register dump and debug data")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all-mask IP address to Big Endian, instead, for comparison.
Fixes: f286dd8eaa ("cxgb4: use correct type for all-mask IP address comparison")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes ip dst and ipv6 address filters.
There were 2 mistakes in the code, which led to the issue:
* invalid register was used for ipv4 dst address;
* incorrect write order of dwords for ipv6 addresses.
Fixes: 23e7a718a4 ("net: aquantia: add rx-flow filter definitions")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The queue reset pattern is used in a couple different places,
only slightly different from each other, and could cause
issues if one gets changed and the other didn't. This puts
them together so that only one version is needed, yet each
can have slighty different effects by passing in a pointer
to a work function to do whatever configuration twiddling is
needed in the middle of the reset.
This specifically addresses issues seen where under loops
of changing ring size or queue count parameters we could
occasionally bump into the netdev watchdog.
v2: added more commit message commentary
Fixes: 4d03e00a21 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating debug dump, driver firstly collects all data in binary
form, and then performs per-feature formatting to human-readable if it
is supported.
For ethtool -d, this is roughly incorrect for two reasons. First of all,
drivers should always provide only original raw dumps to Ethtool without
any changes.
The second, and more critical, is that Ethtool's output buffer size is
strictly determined by ethtool_ops::get_regs_len(), and all data *must*
fit in it. The current version of driver always returns the size of raw
data, but the size of the formatted buffer exceeds it in most cases.
This leads to out-of-bound writes and memory corruption.
Address both issues by adding an option to return original, non-formatted
debug data, and using it for Ethtool case.
v2:
- Expand commit message to make it more clear;
- No functional changes.
Fixes: c965db4446 ("qed: Add support for debug data collection")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rwlock.h should not be included directly. Instead linux/splinlock.h
should be included. Including it directly will break the RT build.
Fixes: 549c243e4e ("net/mlx5e: Extract neigh-specific code from en_rep.c to rep/neigh.c")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ISR, we poll the event register for the queues in need of
service and then enter polled mode. After this point, the event
register will never be read again until we exit polled mode.
In a scenario where a UDP flow is routed back out through the same
interface, i.e. "router-on-a-stick" we'll typically only see an rx
queue event initially. Once we start to process the incoming flow
we'll be locked polled mode, but we'll never clean the tx rings since
that event is never caught.
Eventually the netdev watchdog will trip, causing all buffers to be
dropped and then the process starts over again.
Rework the NAPI poll to keep trying to consome the entire budget as
long as new events are coming in, making sure to service all rx/tx
queues, in priority order, on each pass.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analysis flags this garbage return
drivers/net/ethernet/marvell/sky2.c:208:2: warning: Undefined or garbage value returned to caller [core.uninitialized.UndefReturn]
return v;
^~~~~~~~
static inline u16 gm_phy_read( ...
{
u16 v;
__gm_phy_read(hw, port, reg, &v);
return v;
}
__gm_phy_read can return without setting v.
So handle similar to skge.c's gm_phy_read, initialize v.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include "ipa_gsi.h" in "ipa_gsi.c", so the public functions are
defined before they are used in "ipa_gsi.c". This addresses some
warnings that are reported with a "W=1" build.
Fixes: c3f398b141 ("soc: qcom: ipa: IPA interface to GSI")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers to two struct types are used in "ipa_gsi.h", without those
struct types being forward-declared. Add these declarations.
Fixes: c3f398b141 ("soc: qcom: ipa: IPA interface to GSI")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with "W=1" did exactly what it was supposed to do, namely
point out some suspicious-looking code to be verified not to contain
bugs.
Some QMI message structures defined in "ipa_qmi_msg.c" contained
some bad field names (duplicating the "elem_size" field instead of
defining the "offset" field), almost certainly due to copy/paste
errors that weren't obvious in a scan of the code. Fix these bugs.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable promisc mode of PF, set VF link state to enable, and
run iperf of the VF, then do self test of the PF. The self test
will fail with a low frequency, and may cause a use-after-free
problem.
[ 87.142126] selftest:000004a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 87.159722] ==================================================================
[ 87.174187] BUG: KASAN: use-after-free in hex_dump_to_buffer+0x140/0x608
[ 87.187600] Read of size 1 at addr ffff003b22828000 by task ethtool/1186
[ 87.201012]
[ 87.203978] CPU: 7 PID: 1186 Comm: ethtool Not tainted 5.5.0-rc4-gfd51c473-dirty #4
[ 87.219306] Hardware name: Huawei TaiShan 2280 V2/BC82AMDA, BIOS TA BIOS 2280-A CS V2.B160.01 01/15/2020
[ 87.238292] Call trace:
[ 87.243173] dump_backtrace+0x0/0x280
[ 87.250491] show_stack+0x24/0x30
[ 87.257114] dump_stack+0xe8/0x140
[ 87.263911] print_address_description.isra.8+0x70/0x380
[ 87.274538] __kasan_report+0x12c/0x230
[ 87.282203] kasan_report+0xc/0x18
[ 87.288999] __asan_load1+0x60/0x68
[ 87.295969] hex_dump_to_buffer+0x140/0x608
[ 87.304332] print_hex_dump+0x140/0x1e0
[ 87.312000] hns3_lb_check_skb_data+0x168/0x170
[ 87.321060] hns3_clean_rx_ring+0xa94/0xfe0
[ 87.329422] hns3_self_test+0x708/0x8c0
The length of packet sent by the selftest process is only
128 + 14 bytes, and the min buffer size of a BD is 256 bytes,
and the receive process will make sure the packet sent by
the selftest process is in the linear part, so only check
the linear part in hns3_lb_check_skb_data().
So fix this use-after-free by using skb_headlen() to dump
skb->data instead of skb->len.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading driver, if flag HNS3_NIC_STATE_INITED has been
already cleared, the debugfs will not be uninitialized, so fix it.
Fixes: b2292360bb ("net: hns3: Add debugfs framework registration")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asserts VF reset fail, flag HCLGEVF_STATE_CMD_DISABLE
and handshake status should not set, otherwise the retry will
fail. So adds a check for asserting VF reset and returns
directly when fails.
Fixes: ef5f8e507e ("net: hns3: stop handling command queue while resetting VF")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a PF reset pending before FLR prepare, FLR's
preparatory work will not fail, but the FLR rebuild procedure
will fail for this pending. So this PF reset pending should
be handled in the FLR preparatory.
Fixes: 8627bdedc4 ("net: hns3: refactor the precedure of PF FLR")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes,
then this driver will prepend a length field of 2 bytes,
then the underlying Ethernet device will prepend its own header.
So, the header length required should be:
-1 + 3 + 2 + "the header length needed by the underlying device".
This patch fixes kernel panic when this driver is used with AF_PACKET
SOCK_DGRAM sockets.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet can have only two bridge interface.
One of them is a link interface and another one is added by
the master operation.
rmnet interface shouldn't allow adding additional
bridge interfaces by mater operation.
But, there is no code to deny additional interfaces.
So, interface leak occurs.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set dummy1 master rmnet0
ip link set dummy2 master rmnet0
ip link del rmnet0
In the above test command, the dummy0 was attached to rmnet as VND mode.
Then, dummy1 was attached to rmnet0 as BRIDGE mode.
At this point, dummy0 mode is switched from VND to BRIDGE automatically.
Then, dummy2 is attached to rmnet as BRIDGE mode.
At this point, rmnet0 should deny this operation.
But, rmnet0 doesn't deny this.
So that below splat occurs when the rmnet0 interface is deleted.
Splat looks like:
[ 186.684787][ C2] WARNING: CPU: 2 PID: 1009 at net/core/dev.c:8992 rollback_registered_many+0x986/0xcf0
[ 186.684788][ C2] Modules linked in: rmnet dummy openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_x
[ 186.684805][ C2] CPU: 2 PID: 1009 Comm: ip Not tainted 5.8.0-rc1+ #621
[ 186.684807][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 186.684808][ C2] RIP: 0010:rollback_registered_many+0x986/0xcf0
[ 186.684811][ C2] Code: 41 8b 4e cc 45 31 c0 31 d2 4c 89 ee 48 89 df e8 e0 47 ff ff 85 c0 0f 84 cd fc ff ff 5
[ 186.684812][ C2] RSP: 0018:ffff8880cd9472e0 EFLAGS: 00010287
[ 186.684815][ C2] RAX: ffff8880cc56da58 RBX: ffff8880ab21c000 RCX: ffffffff9329d323
[ 186.684816][ C2] RDX: 1ffffffff2be6410 RSI: 0000000000000008 RDI: ffffffff95f32080
[ 186.684818][ C2] RBP: dffffc0000000000 R08: fffffbfff2be6411 R09: fffffbfff2be6411
[ 186.684819][ C2] R10: ffffffff95f32087 R11: 0000000000000001 R12: ffff8880cd947480
[ 186.684820][ C2] R13: ffff8880ab21c0b8 R14: ffff8880cd947400 R15: ffff8880cdf10640
[ 186.684822][ C2] FS: 00007f00843890c0(0000) GS:ffff8880d4e00000(0000) knlGS:0000000000000000
[ 186.684823][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 186.684825][ C2] CR2: 000055b8ab1077b8 CR3: 00000000ab612006 CR4: 00000000000606e0
[ 186.684826][ C2] Call Trace:
[ 186.684827][ C2] ? lockdep_hardirqs_on_prepare+0x379/0x540
[ 186.684829][ C2] ? netif_set_real_num_tx_queues+0x780/0x780
[ 186.684830][ C2] ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[ 186.684831][ C2] ? __kasan_slab_free+0x126/0x150
[ 186.684832][ C2] ? kfree+0xdc/0x320
[ 186.684834][ C2] ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[ 186.684835][ C2] unregister_netdevice_many.part.135+0x13/0x1b0
[ 186.684836][ C2] rtnl_delete_link+0xbc/0x100
[ ... ]
[ 238.440071][ T1009] unregister_netdevice: waiting for rmnet0 to become free. Usage count = 1
Fixes: 037f9cdf72 ("net: rmnet: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending mailbox in the work of aeq event, another aeq event
will be triggered. because the last aeq work is not exited and only
one work can be excuted simultaneously in the same workqueue, mailbox
sending function will return failure of timeout. We create and use
another workqueue to fix this.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9893 3-Port Gigabit Ethernet Switch can be controlled via SPI,
I²C or MDIO (very limited and not supported by this driver). While there
is already a compatible entry for the SPI bus, it was missing for I²C.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_dev_cap and set_resources_state functions may return a positive
value because of hardware failure, and the positive return value
can not be passed to ERR_PTR directly.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_prep_fw goto bye tag with positive return value when something
bad happened and which can not free resource in adap_init0.
so fix it to return negative value.
Fixes: 16e47624e7 ("cxgb4: Add new scheme to update T4/T5 firmware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new function ipa_cmd_tag_process() that simply allocates a
transaction, adds a tag process command to it to clear the hardware
pipeline, and commits the transaction.
Call it in from ipa_endpoint_suspend(), after suspending the modem
endpoints but before suspending the AP command TX and AP LAN RX
endpoints (which are used by the tag sequence).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AP LAN RX endpoint should not have download checksum offload
enabled.
The receive handler does properly accommodate the trailer that's
added by the hardware, but we ignore it.
Fixes: 1ed7d0c0fd ("soc: qcom: ipa: configuration data")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gsi_channel_stop(), there's a check to see if the channel might
have entered STOPPED state since a previous call, which might have
timed out before stopping completed.
That check actually belongs in gsi_channel_stop_command(), which is
called repeatedly by gsi_channel_stop() for RX channels.
Fixes: 650d160382 ("soc: qcom: ipa: the generic software interface")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for short preambles was added, it incorrectly keyed its
decision off state->speed instead of state->interface. state->speed
is not guaranteed to be correct for in-band modes, which can lead to
short preambles being unexpectedly disabled.
Fix this by keying off the interface mode, which is the only way that
mvneta can operate at 2.5Gbps.
Fixes: da58a931f2 ("net: mvneta: Add support for 2500Mbps SGMII")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tun driver passes up skb->protocol to userspace in the form of PI headers.
For AF_PACKET injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and the tun driver
then gives userspace bogus values that it can't deal with.
Note that this isn't the case with tap, because tap already benefits
from the shared infrastructure for ethernet headers. But with tun,
there's nothing.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
Reported-by: Hans Wippel <ndev@hwipl.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lockdep_set_class_and_subclass() is meant to reduce
the _nested() annotations by assigning a default subclass.
For addr_list_lock, we have to compute the subclass at
run-time as the netdevice topology changes after creation.
So, we should just get rid of these
lockdep_set_class_and_subclass() and stick with our _nested()
annotations.
Fixes: 845e0ebb44 ("net: change addr_list_lock back to static key")
Suggested-by: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rings bitmap of an interrupt vector encodes
which of the device's rings were assigned to that
interrupt vector.
Hence the iteration range of the tx rings bitmap
(for_each_set_bit()) should be the total number of
Tx rings of that netdevice instead of the number of
rings assigned to the interrupt vector.
Since there are 2 cores, and one interrupt vector for
each core, the number of rings asigned to an interrupt
vector is half the number of available rings.
The impact of this error is that the upper half of the
tx rings could still generate interrupts during napi
polling.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the network stack know the real number of queues that
we are using.
v2: added error checking
Fixes: 49d3b49367 ("ionic: disable the queues on link down")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically no drivers care about the return value here, and there's no
__must_check that would make casting to void sensible, so remove it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes last saved fdb index in fdb dump handler when
handling fdb's with nhid.
Fixes: 1274e1cc42 ("vxlan: ecmp support for mac fdb entries")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_gating_cfg_time_to_interval function does this, as per the
comments:
/* The gate entries contain absolute times in their e->interval field. Convert
* that to proper intervals (i.e. "0, 5, 10, 15" to "5, 5, 5, 5").
*/
To perform that task, it iterates over gating_cfg->entries, at each step
updating the interval of the _previous_ entry. So one interval remains
to be updated at the end of the loop: the last one (since it isn't
"prev" for anyone else).
But there was an erroneous check, that the last element's interval
should not be updated if it's also the only element. I'm not quite sure
why that check was there, but it's clearly incorrect, as a tc-gate
schedule with a single element would get an e->interval of zero,
regardless of the duration requested by the user. The switch wouldn't
even consider this configuration as valid: it will just drop all traffic
that matches the rule.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tas_data->enabled would remain true even after deleting all
tc-gate rules from the switch ports, which would cause the
sja1105_tas_state_machine to get unnecessarily scheduled.
Also, if there were any errors which would prevent the hardware from
enabling the gating schedule, the sja1105_tas_state_machine would
continuously detect and print that, spamming the kernel log, even if the
rules were subsequently deleted.
The rules themselves are _not_ active, because sja1105_init_scheduling
does enough of a job to not install the gating schedule in the static
config. But the virtual link rules themselves are still present.
So call the functions that remove the tc-gate configuration from
priv->tas_data.gating_cfg, so that tas_data->enabled can be set to
false, and sja1105_tas_state_machine will stop from being scheduled.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sja1105_compose_gating_subschedule is not prepared to be
called for the case where we want to recompute the global tc-gate
configuration after we've deleted those actions on a port.
After deleting the tc-gate actions on the last port, max_cycle_time
would become zero, and that would incorrectly prevent
sja1105_free_gating_config from getting called.
So move the freeing function above the check for the need to apply a new
configuration.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that sja1105_compose_gating_subschedule must also be called
from sja1105_vl_delete, to recalculate the overall tc-gate
configuration. Currently this is not possible without introducing a
forward declaration. So move the function at the top of the file, along
with its dependencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA buffers were not freed on failure path of at91ether_open().
Along with changes for freeing the DMA buffers the enable/disable
interrupt instructions were moved to at91ether_start()/at91ether_stop()
functions and the operations on at91ether_stop() were done in
their reverse order (compared with how is done in at91ether_start()):
before this patch the operation order on interface open path
was as follows:
1/ alloc DMA buffers
2/ enable tx, rx
3/ enable interrupts
and the order on interface close path was as follows:
1/ disable tx, rx
2/ disable interrupts
3/ free dma buffers.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
