"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200117230845.25190-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Depending on bcm2711's revision its emmc2 controller might have
different DMA constraints. Raspberry Pi 4's firmware will take care of
updating those, but only if a certain alias is found in the device tree.
So, move emmc2 into its own bus, so as not to pollute other devices with
dma-ranges changes and create the emmc2bus alias.
Based in Phil ELwell's downstream implementation.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200304132437.20164-1-nsaenzjulienne@suse.de
Commit a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A test with the command below gives these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-r89.dt.yaml: /: 'model'
is a required property
Fix this error by adding the missing model properties to
the involved dts files.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/root-node.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200304074051.8742-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The AM57xx family of SoCs contains two identical PRU-ICSS instances
that have a very unique SYSC register. The IPs do not have any
PRCM reset lines unlike those on AM33xx/AM437x SoCs. Add the PRUSS
interconnect target-module nodes with all the required properties.
Each of the PRUSS devices themselves shall be added as child nodes
to the corresponding interconnect node in the future. The PRU-ICSS
instances are only available on AM57xx family of SoCs and are not
supported on DRA7xx family of SoCs in general, so the target module
nodes are added in a separate dtsi file. This new dtsi file is
included in all the AM57xx SoC dtsi files, so the nodes are
automatically inherited and enabled on all AM57xx boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM437x family of SoCs contains two dissimilar PRU-ICSS instances,
but leverage a common reset line and SYSCFG from the larger PRU-ICSS1
instance. This SYSC register has also very unique bit-fields. Both
the IPs require the PRCM reset to be deasserted to be able to access
any registers. Add a common PRUSS interconnect target-module with all
the required properties.
The PRUSS devices themselves shall be added as child nodes to this
interconnect node in the future. The PRU-ICSS instances are not
supported on AM4372 SoC though in the AM437x family, so the target
module node should be disabled in any derivative board files that
use this SoC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on some AM33xx SoCs has a very unique SYSC
register. The IP also uses a hard-reset line, and requires this
PRCM reset to be deasserted to be able to access any registers.
Update the existing PRUSS interconnect target-module with all
the required properties.
The PRUSS device itself shall be added as a child node to this
interconnect node in the future. PRU-ICSS is not supported on
AM3351/AM3352/AM3354 SoCs though in the AM33xx family, so the
target module node should be disabled in derivative board files
that use any of these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Note that we also fix a harmless typo for the node name, it's
dispc@400, not dispc@4000.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.
To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Note that we must disable smart idle modes for HDMI audio like we've
done with the legacy platform data. And HDMI needs both hdmi clock
and dss clock to operate.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
The display subsystem (DSS) is in a 16MB interconnect target module
mapped to l4 and l3 buses. We are only using the l3 port as recommended
by the TRM. So there is no need to configure l4 ranges like we've done
for l4 ABE instance for example.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Let's also add add a note about using only the l3 access without l4
as noted in the TRM.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IB2 syscon should not have any funny names, just call
it syscon@ as per the convention so the schema will apply
properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'dma-ranges' at the top level doesn't make sense. 'dma-ranges' implies
there is a parent bus node with '#address-cells' and '#size-cells' which
is impossible here.
Likely this translation needs to be moved down to sub-nodes that need
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for RGMII mode")
caused a regression for dm814x boards where NFSroot would no longer work.
Let's fix the issue by configuring "rgmii-id" mode as internal delays are
needed that is no longer the case with "rgmii" mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add vcc50_hdmi regulator for Vyasa RK3288 board.
VCC50_HDMI is the real name used for this regulator as
per the schematics.
This regulator used for HDMI connector by detecting the
cable via HDMI_EN gpio and input rails are sourced from
VSUS_5V regulator.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200123134641.30720-3-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to hardware schematics of Vyasa RK3288 the
actual name used for vcc10_lcd is vdd10_lcd.
regulator suspend voltage can rail upto 1.0V not 1.8V.
Fix the name and suspend voltage for vcc10_lcd regulator.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200123134641.30720-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
'rockchip-pmu-sram.txt' inherit properties from 'sram.yaml'.
Fix this error by adding 'sram' to the bus_intmem nodename
in 'rk3288.dtsi'. But 'sram' is also a node name already in use.
To prevent confusion rename it to 'pmu_sram'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rk3036-evb.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rk3036-kylin.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
Fix this error by adding sram to the bus_intmem nodename
in rk3036.dtsi.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rv1108-evb.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
Fix this error by adding sram to the bus_intmem nodename
in rv1108.dtsi.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml: usb@30180000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@30180000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3228-evb.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3229-evb.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3229-xms6.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
'g-use-dma' is not a valid option in dwc2.yaml, so remove it
from all Rockchip dtsi files.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
g-use-dma was deprecated in november 2016, see
https://patchwork.kernel.org/patch/9420553/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228113922.20266-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
5.6, please pull the following:
- Stefan adds missing Device Tree properties for the Raspberry Pi 3B and
4 LEDs to have proper default configuration
- Nicolas adds an alias for the PCIe root complex node that is looked up
by the Raspberry Pi firmware for patching in specific properties
-----BEGIN PGP SIGNATURE-----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=On3Q
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.6/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.6, please pull the following:
- Stefan adds missing Device Tree properties for the Raspberry Pi 3B and
4 LEDs to have proper default configuration
- Nicolas adds an alias for the PCIe root complex node that is looked up
by the Raspberry Pi firmware for patching in specific properties
* tag 'arm-soc/for-5.6/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
Link: https://lore.kernel.org/r/20200228181144.15148-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
-----BEGIN PGP SIGNATURE-----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=UHKz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few fixes for omaps for v5.6-rc cycle
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
* tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: dra7-l4: mark timer13-16 as pwm capable
ARM: dts: dra7xx-clocks: Fixup IPU1 mux clock parent source
ARM: dts: am437x-idk-evm: Fix incorrect OPP node names
ARM: dts: dra7-evm: Rename evm_3v3 regulator to vsys_3v3
Link: https://lore.kernel.org/r/pull-1582903541-589933@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
G3D power domain in Exynos5420 SoC is supplied from PVDD_G3DS_1V0 and
PVDD_G3D_1V0. Besides the main GPU MALI module it also contains the power
domain control logic and clocks. Turning the power supplies off causes
the power domain to fail to operate properly if GPU drivers are loaded as
modules. GPU should use PVDD_G3D_1V0 supply mainly to control the DVFS.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
G3D power domain in Exynos5422 SoC is supplied from VDD_G3D. Besides the
main GPU MALI module it also contains the power domain control logic and
clocks. Turning the VDD_G3D power supply off causes the power domain to
fail to operate properly and breaks for example system suspend/resume.
GPU should use VDD_G3D supply mainly to control the DVFS.
Fixes: 1a5a85c564 ("ARM: dts: exynos: Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 73f9de0c7f ("ARM: dts: uniphier: Add generic compatible string
for I2C EEPROM") did not touch this node.
Add the compatible string prefixed "atmel," so that this matches to the
OF table.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern
"^(cache-controller|cpu)(@[0-9a-f,]+)*$" defined in
schemas/cache-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
l2-cache@500c0000: $nodename:0: 'l2-cache@500c0000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^nand-controller(@.*)?" defined
in Documentation/devicetree/bindings/mtd/nand-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
nand@68000000: $nodename:0: 'nand@68000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^interrupt-controller(@[0-9a-f,]+)*$"
defined in schemas/interrupt-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
make ARCH=arm dtbs_check' will show warnings like this:
aidet@5fc20000: $nodename:0: 'aidet@5fc20000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^mmc(@.*)?$" defined in
Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
sdhc@5a000000: $nodename:0: 'sdhc@5a000000' does not match '^mmc(@.*)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some bcm2711 revisions have different DMA constraints on the their PCIE
bus. The lower common denominator, being able to access the lower 3GB of
memory, is the default setting for now. Newer SoC revisions are able to
access the whole memory space.
Raspberry Pi 4's firmware is aware of this limitation and will correct
the PCIE's dma-ranges property if a pcie0 alias is available. So add
it.
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the missing properties to the PWR LED for the RPi 3 & 4 boards,
which are already set for the other boards. Without them we will lose
the LED state after suspend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXlY78AAKCRCKwlD9ZEnx
cAR9APdKGcY7roK82m1uLIsCohHOdwikY4qvR+cVniRKgwspAP9Q3NNCXhelEEed
S2JMLficspDnR+BuWR3gyg173Z74CQ==
=P/qq
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas Fixes for v5.6
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
* tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
arm64: defconfig: Replace ARCH_R8A7796 by ARCH_R8A77960
Link: https://lore.kernel.org/r/20200226105236.18368-1-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
The OMAP4 DSP hwmod is used in DT, but the DT node is not
probing any real driver. The DSP device-tree node shall be
updated as per the new OMAP remoteproc bindings with the
underneath MMU device relying on the ti-sysc infrastructure.
Drop the legacy hwmod data for the DSP device along with the
custom ti,hwmods property. They have to be dropped together
since the early platform data init code is based on the custom
ti,hwmods property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add idle_states table for CPU on am437x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add idle_states table for CPU on am335x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a second PWM unit available in the PL I/O block.
Add a node and pinmux definition for it.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The last 8MB of physical memory on Artik520 family boards is reserved for
secure firmware. Adjust the total amount of the memory defined in
exynos3250-artik5.dtsi to match the memory available for the Linux kernel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5 ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables passive cooling by down-regulating CPU voltage
and frequency.
For the trip points, I used values from the BSP code directly.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This enables passive cooling by down-regulating CPU voltage
and frequency.
For trip points, I used a slightly lowered values from the BSP
code. The critical temperature of 110°C from BSP code seemed
like a lot, so I rounded it off to 100°C.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the gpio-ranges property to almost all of
the Qualcomm ARM platforms that utilize the pinctrl-msm
framework.
The gpio-ranges property is part of the gpiolib subsystem.
As a result, the binding text is available in section
"2.1 gpio- and pin-controller interaction" of
Documentation/devicetree/bindings/gpio/gpio.txt
For more information please see the patch titled:
"pinctrl: msm: fix gpio-hog related boot issues" from
this series.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr> [ipq4019]
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200108125455.308969-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5TuEMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4a+Qf9Enb2G47LTMeYH5JYhm2anDQ4lz+8
Og1bcGPYKilDhc4YzpAIhRnOTLa9TietZSS0tyNFk37GDfKRjn9gxXDRbI+4lrJc
UOSLpWCB4BnzKc+FoCHC37jkdkMD3V2E5MmFHtYkGYmH0DAi8cLmGebmgGujd0GJ
lx2/5EbxKoJxeA2i79H5OAPBhglJsEnPTSulZ+jUdLzJfBlRBIQBc3oPcwnRIibr
VUbLc4Gkb2kTe6NwdQTjqI+4BTHv7/4m+twOojO5Z8QBH4X+3bkLnLiylhuqHBeR
cDXGL7sHkekZhDQ3OwIMiT/5cc8SxplqAl6QMm8+/9gq7KfAucy8Psokow==
=dg69
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.
This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.
The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.
After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.
The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.
For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.
-----BEGIN PGP SIGNATURE-----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=Pox9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix LCD backlight issue for droid4
There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.
This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.
The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.
After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.
The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.
For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.
* tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: droid4: Configure LED backlight for lm3532
backlight: add led-backlight driver
Link: https://lore.kernel.org/r/pull-1582303901-96693@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We are missing AESS for omap5. Looks like it's similar to what we have
for omap4, and this gets ti-sysc interconnect target module driver to
detect it properly.
Note that we currently have no child device driver available for it.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "renesas,rcar-sata" compatible value was deprecated by
"renesas,sata-r8a7779" many years ago, in commit e67adb4e66
("sata_rcar: Add R-Car Gen2 SATA PHY support"). Drop it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200219153929.11073-1-geert+renesas@glider.be
Add reset control properties to the devices node for the Display Units
on all supported RZ/G1 SoCs. Note that on these SoCs, there is only a
single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-3-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen2 SoCs. Note that on these SoCs, there is
only a single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-2-geert+renesas@glider.be
The DU DT bindings have been updated to drop the reg-names property.
Update the r8a7745 device tree accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218132217.21454-1-geert+renesas@glider.be
USB-ID signal has a pullup on the schematic, but in reality it's not
pulled up, so add a GPIO pullup. And we also need a usb0_vbus_power-supply
for VBUS detection.
This fixes OTG mode detection and charging issues on TBS A711 tablet.
The issues came from ID pin reading 0, causing host mode to be enabled,
when it should not be, leading to DRVVBUS being enabled, which disabled
the charger.
Fixes: f2f221c781 ("ARM: dts: sun8i: a711: Enable USB OTG")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Property dr_mode = "otg" is the default in sun8i-a83t.dtsi
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
What works:
- Serial console
- mmc0, mmc2 (both microSD card slots on the board)
- All buttons (gpio and lradc based)
- Power LED
- PMIC
- RTC
- USB OTG/gadgets mode
- Realtek USB WiFi
- Display backlight
- eInk display SPI NOR flash memory
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Node name should be generic, use "ocotp-ctrl" instead of "ocotp"
for all i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "watchdog" instead of "wdog" for
wdog nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fixed regulators defined for Arndale5250 boards have no control lines,
so mark them as 'always-on' to better describe the hardware and also kill
the strange messages like 'MAIN_DC: disabling' after boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to the schematic, both eMMC and SDMMC use dedicated fixed
regulators connected directly to the DC5V and MAIN_DC rails. Remove the
GPX1-1 line assigned to the MMC regulator, because such control
connection doesn't exist. Also change its name to VDD_MMC to avoid
conflict with LDO18 output of S5M8767 PMIC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
To use Energy Aware Scheduler (EAS) the Energy Model (EM) should be
registered for CPUs. Add dynamic-power-coefficient into CPU nodes which
let CPUFreq subsystem register the EM structures. This will increase
energy efficiency of big.LITTLE platforms.
The 'dynamic-power-coefficient' values have been obtained experimenting
with different workloads. The power measurements taken from big CPU
Cluster and LITTLE CPU Cluster has been compared with official documents
and synthetic workloads estimations. The effective power ratio between
Cortex-A7 and Cortex-A15 CPUs (~3x) is also aligned with documentation.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DMTimers 13 - 16 are PWM capable and also can be used for CPTS input
signals generation. Hence, mark them as "ti,timer-pwm".
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU1 functional clock is the output of a mux clock (represented
by ipu1_gfclk_mux previously) and the clock source for this has been
updated to be sourced from dpll_core_h22x2_ck in commit 39879c7d96
("ARM: dts: dra7xx-clocks: Source IPU1 functional clock from CORE DPLL").
ipu1_gfclk_mux is an obsolete clock now with the clkctrl conversion,
and this clock source parenting is lost during the new clkctrl layout
conversion.
Remove this stale clock and fix up the clock source for this mux
clock using the latest equivalent clkctrl clock. This restores the
previous logic and ensures that the IPU1 continues to run at the
same frequency of IPU2 and independent of the ABE DPLL.
Fixes: b5f8ffbb6f ("ARM: dts: dra7: convert to use new clkctrl layout")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable
OPP50 for MPU") adjusts couple of OPP nodes defined in the
common am4372.dtsi file, but used outdated node names. This
results in these getting treated as new OPP nodes with missing
properties.
Fix this properly by using the correct node names as updated in
commit b9cb2ba718 ("ARM: dts: Use - instead of @ for DT OPP
entries for TI SoCs").
Reported-by: Roger Quadros <rogerq@ti.com>
Fixes: 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable OPP50 for MPU")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the new schematics it is renamed and the same name is used on other
dra7 boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define pins for LVDS channels 0 and 1, configure reset line for tcon0 and
provide sample LVDS panel, connected to tcon0.
Signed-off-by: Andrey Lebedev <andrey@lebedev.lt>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The display DRC nodes have an assigned clocks property, while the driver
also enforces it.
Since assigned-clocks is pretty fragile anyway, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The display backend nodes have an assigned clocks property, while the driver
also enforces it.
Since assigned-clocks is pretty fragile anyway, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With the LED backlight changes merged, we still need the dts configured
to have backlight working for droid4. Based on an earlier patch from
Pavel Machek <pavel@ucw.cz>, let's configure the backlight but update
the value range to be more usable.
We have a range of 256 register values split into 8 steps, so we can
generate the brightness levels backwards with:
$ for i in 0 1 2 3 4 5 6 7; do echo "255 - ${i} * (256 / 8)" | bc; done
To avoid more confusion why the LCD backlight is still not on, let's
also enable LED backlight as a loadable module for omap2plus_defconfig.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DCE/DTE to UART pins macro defines to distinguish the
DCE and DTE functions, keep old defines at the end of file
for some time to make it backward compatible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The nodes with name scpsys actually implement a power-controller.
Rename the nodes to match the bindings description.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Node name should be generic, use "clock-controller" instead of
"ccm" for clks node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "keypad" instead of "kpp" for kpp node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "timer" instead of "gpt" for gpt node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per devicetree specification, generic names
are recommended to be used, such as bus.
i.MX AIPS is a AHB - IP bridge bus, so
we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/vf*.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sram-node compatible properties have mistakingly combined the
model-specific string with the generic "mtd-ram" string.
Note that neither "cy7c1019dv33-10zsxi, mtd-ram" or
"cy7c1019dv33-10zsxi" are used by any in-kernel driver and they are
not present in any binding.
The physmap driver will however bind to platform devices that specify
"mtd-ram".
Fixes: fc48e76489 ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds defines for another cspi3 configuration.
The defines have been tested on an out-of-tree board.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Increase boot partition size to 32MB to support bigger size kernel image
and FPGA bitstream.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The Testbox board is an open hardware enhancement for the Lamobo R1 router
board. The Testbox board is used in the CI-RT project to manage devices
under test (https://ci-rt.linutronix.de).
The hardware project is located at https://github.com/ci-rt/testbox-shield
The Testbox v2 expands the Lamobo R1 router board with
- a power supply,
- a CAN bus PHY,
- a power control,
- a relay,
- an I2C EEPROM,
- a secure key storage (ATECC608a) and
- two RS232 compliant serial ports.
Co-developed-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Bastian Germann <bage@linutronix.de>
[Maxime: Removed unused pinctrl node]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure that the priority of the RTCs is defined.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The max voltage of SW1A is 3.3V on PF3000 as per
http://cache.freescale.com/files/analog/doc/data_sheet/PF3000.pdf?fsrch=1&sr=1&pageNum=1
While at it, remove the unnecessary leading zero from
the i2c address.
Signed-off-by: André Draszik <git@andred.net>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri SODIMM numbers as GPIO line names on module level. The GPIO
lines with a name are all available on the SODIMM edge connector of the
Colibri iMX7 module and therefore a customer might use it as a GPIO. The
Toradex Evaluation Board has the SODIMM numbers printed on the silk-
screen. This allows a customer to quickly control a GPIO on a pin-header
by using the name printed next to it.
Putting the GPIO line name on module level makes sure that a customer
gets a reasonable default. If more meaningful names are available on a
custom carrier board, the user can overwrite the line names in a carrier
board level device tree.
The eMMC based modules share all GPIO names except two GPIOs on bank 6
which are not available on the raw NAND devices. Hence overwrite GPIO
line names of bank 6 in the eMMC specific device tree file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
Background discussion:
https://www.spinics.net/lists/stable/msg361156.html
Fixes: c7861adbe3 ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At imx7ulp evk, all USBOTG1 OC (Over Current) function pins are
used by others, and the USB driver doesn't support OC function
through the GPIO, so we disable the OC function for this board
as well as delete the pinctrl for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i.MX7D Document Number: IMX7DCEC Rev. 6, 03/2019,
there are only consumer/industrial parts, and 1.2GHz
is only support in consumer parts.
So exclude automotive from 792/996MHz/1.2GHz and exclude
industrial from 1.2GHz.
Fixes: d7bfba7296 ("ARM: dts: imx7d: Update cpufreq OPP table")
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After reset the oc protection polarity is set to active high on imx6.
If the polarity is not specified in device tree it is not changed.
The imx6dl-yapp4 platform uses an active-low oc signal so explicitly
configure that in the device tree.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the USB host port on the APx4 development board.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Documentation/devicetree/bindings/display/mxsfb.txt states that
the current display bindings format used in this dts is deprecated.
Convert it to the preferred DRM bindings instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the bluetooth found on the Nexus 5 phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: formatting cleanups; remove sleep clock; patch
extracted from much larger out of tree patch.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20200129232031.34538-4-masneyb@onstation.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add blsp2_uart10 node in order to support bluetooth on the Nexus 5
phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: use constants in interrupts property; patch
extracted from much larger out of tree patch.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20200129232031.34538-3-masneyb@onstation.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This exact node has been included in Amami DTS
ever since 2017, turns out it works perfectly
fine with Honami, as tested with postmarketOS.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200118165518.36036-1-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove "snps,phy-bus-name", "snps,phy-bus-id" and "snps,phy-addr"
properties which are deprecated.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add trip points and cooling maps for GPU thermal zone for Odroid
XU3/XU4/HC1 boards. Trip points are based on the CPU thermal zone for the
those boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bootloader on Odroid U2/X2/U3 boards configures main ARM clock to
1GHz. During the system shutdown procedure Linux kernel selects so called
'suspend-opp' for the CPU cores, what means that ARM clock is set to
800MHz and the CPU supply voltage is adjusted to that value. PMIC
configuration is preserved during the board reboot. Later when the
bootloader tries to enter the 1GHz mode, the voltage value configured by
the kernel might be not high enough for the CPU to operate stable. This
depends on the individual physical properties of each SoC (usually it is
related to the production series) and varies between the boards.
Typically most of the Odroid U3 boards work fine, while most of the U2
and X2 hangs during the reboot.
This commit switches suspend-opp to 1GHz for the Odroid U2/X2/U3 boards,
what finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change stmfx node name to fit with yaml requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Change stmfx node name to fit with yaml requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
resets property is well-managed in DMA drivers. In previous products,
there were no reset lines, that's why they are missing here in dma1, dma2,
dmamux and mdma nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Now that st,stm32mp15-hsotg is used, dual role is supported. ID pin is
managed to detect the current role.
On stm32mp157c-ev1, Host mode requires a vbus-supply property. Charge pump
for vbus is provided by PMIC VBUS_OTG.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinctrl definition for USB High-Speed OTG ID pin and USB Full-Speed OTG
DP and DM lines that can be used on stm32mp15.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Using the st,stm32mp15-hsotg compatible allows to use USB OTG with Dual Role
mode support.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Theses 3 properties are not coded in driver so remove them from the DTS.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP157C and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add missing 'eth-ck' clock to the ethernet node on stm32mp1. These
clock are used to generate external clock signal for the PHY in case
'st,eth_ref_clk_sel' is specified.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Christophe ROULLIER <christophe.roullier@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinmux entry for SAI2A with alternative pin configuration.
This is useful in combination with sai2b_pins_b e.g. for codecs
like SGTL5000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These nodes should be named dsi-controller@* so fix it up.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add clocks for SPIBSC blocks.
Also modify the flash node for the GR-PEACH board at the same time
because now that the SPIBSC clock is identified, if it is not used
by any driver, it will be turned off at the end of kernel boot.
That would not work out so well for an XIP system such as GR-PEACH.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20200210123153.8257-1-chris.brandt@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To improve human readability and enable automatic validation, the tuples
in the "operating-points" properties of CPU nodes should be grouped.
Fix this by grouping the tuples of these properties using angle brackets
in the DTS files for all Renesas SoCs that don't already do so.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191231141642.31609-1-geert+renesas@glider.be
The ethernet PHY reset GPIO was missing and the kernel was depending
solely on the bootloader to bring the PHY out of reset. Fix this to
get rid of the dependency on bootloader.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200115051225.7346-1-marek.vasut@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When the raw numbers used for clk and reset indices in the EMAC device
node were converted to the new macros, the order of the clk and reset
properties was overlooked, and thus the incorrect macros were used.
This results in the EMAC being non-responsive, as well as an oops due
to incorrect usage of the reset control.
Correct the macro types, and also reorder the clk and reset properties
to match all the other device nodes.
Fixes: 765866edb1 ("ARM: dts: sunxi: Use macros for references to CCU clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, sensor0 for CPU, sensor1 for GPU.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lnYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3wZAP/3wtT+fr/obB/62XkEsVMXl4PZolG/EpJM7j
RlPCFSr9C5ik9PyvoKqbJHkyrTlzF8Op8Qbv7oVisPbAJ+/qpGF+xFI6ieJD1HGF
TAz1prNo57ZJ6BXm/oTWmQggjxuQVdo/mqeQC3812qRNH7lo3495S3EivuRbzs3u
Cs7d29uQHUmpeGrK8R1+co0yV38oMWtUgNRF+UxZH0YdegtITDfg2Af4wqWkvM+8
eqsvQS5V9OaC4t8efP1PzqtUYkOmzua2wzFeubZY513Gpxzl1iKIGLjI+MbfzMp4
RiYftHXj9Jvx00Zg9qGm0Zpw8RwRsY7DyvDFctg3PLvVVgnpjZbPpgD5ttn2YouS
AgsZBtp4h6ydZTxWeZxZOOrn/9n7TGr2SK0I4ijPJIIAPYTQgn6S8P8ELHtNRGj7
tOMP217ozzHi9uQUmyRCNFCqO4pT7sFJJsET0KzDqH9tTSaEZjVx0y2yNn1p70HO
Pv1WqBuniaqVjgn40LcEVbCStgJXDrxejOG9OF92FbqVcrJp9dHsXrIKtkO0WHuF
PtEIKcmwyJ3asns/+HeOIBwJHb5KJ+D2BR+T9K/hZnm8hPcHaZuKGuO/OcucILDk
q3TYKc/nPRBdimKJWyzKlQqtZkbXbCOiApP17iNtLuEtZjf40HOgnBj3LqVH9Jqc
J34LGMlR
=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
the AVS monitor and a subnode for the thermal part.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-4-git-send-email-stefan.wahren@i2se.com
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
-----BEGIN PGP SIGNATURE-----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=u4PK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Late omap dts changes for v5.6 merge window
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
* tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: dts: Add omap3-echo
ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
-----BEGIN PGP SIGNATURE-----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=XXZc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few minor fixes for omaps
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
ARM: dts: am335x-boneblack-common: fix memory size
Link: https://lore.kernel.org/r/pull-1579895109-287828@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With "[PATCHv3] w1: omap-hdq: Simplify driver with PM runtime autosuspend"
we can read the droid4 battery information over 1-wire with this patch
with something like:
# modprobe omap_hdq
# hd /sys/bus/w1/devices/89-*/89-*/nvmem
...
Unfortunately the format of the battery data seems to be Motorola specific
and is currently unusable for battery charger unless somebody figures out
what it means.
Note that currently keeping omap_hdq module loaded will cause extra power
consumption as it seems to scan devices periodically.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We added coulomb counter calibration support With commit 0cb90f071f
("power: supply: cpcap-battery: Add basic coulomb counter calibrate
support"), but we also need to configure the related interrupt.
Without the interrupt calibration happens based on a timeout after two
seconds, with the interrupt the calibration just gets done a bit faster.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be similar to what we have for am335x. The following can be
tested via sysfs with the to ensure the SGX module gets enabled and disabled
properly:
# echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5600fe00 # revision register
0x5600fe00 = 0x40000000
# echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5000fe00
Bus error
Note that this patch depends on the PRM rstctrl driver that has
been recently posted. If the child device driver(s) need to prevent
rstctrl reset on PM runtime suspend, the drivers need to increase
the usecount for the shared rstctrl reset that can be mapped also
for the child device(s) or accessed via dev->parent.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested that the interconnect target module enables and idles
just fine when probed with ti-sysc with PM runtime control via sys:
# echo on > $(find /sys -name control | grep \/5600)
# rwmem 0x5600fe00 # OCP Revision
0x5600fe00 = 0x40000000
# echo auto > $(find /sys -name control | grep \/5600)
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following can be tested via sysfs with the following to ensure the SGX
module gets enabled and disabled properly:
# echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5600fe00 # revision register
0x5600fe00 = 0x40000000
# echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5000fe00
Bus error
Note that this patch depends on the PRM rstctrl driver that has
been recently posted. If the child device driver(s) need to prevent
rstctrl reset on PM runtime suspend, the drivers need to increase
the usecount for the shared rstctrl reset that can be mapped also
for the child device(s) or accessed via dev->parent.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPE node as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for VPE module.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "vpe-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPFE device nodes entries.
Add OmniVision OV2659 sensor device nodes and linkage.
Since Rev1.2a on this board the sensor source clock (xvclk) has a
dedicated 12Mhz oscillator instead of using clkout1.
Add 'audio_mstrclk' fixed clock object to represent it.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPFE device nodes entries.
Add OmniVision OV2659 sensor device nodes and linkage.
The sensor clock (xvclk) is sourced from clkout1.
Add clock entries to properly select clkout1 and set its parent
clock to sys_clkin_ck.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
commit 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Fixes: 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required dtsi node to support the Camera
Adaptation Layer (CAL) for the DRA76 family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the required dtsi node to support the Camera
Adaptation Layer (CAL) for the DRA72 family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CAM nodes as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for CAM domain.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "cam-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
