After updating to the latest Armada XP datasheet, we discovered that
there is a second SPI bus accessible from the MPP pins, called 'spi1'.
In order to be consistent with other SoCs having two SPI busses, this
commit renames the functions of the first SPI bus to 'spi0' instead of
just 'spi'.
This commit obviously breaks the DT backward compatibility for the
people using the "spi" function name in their Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Across all SoCs, even on Armada 370 for SPI0, the clock pin uses the
'sck' subname and not 'clk', so this commit adjusts the code and
documentation accordingly.
Since this commit only changes the subname, DT backward compatibility
is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For consistency with the datasheet, this commit renames the VDD
function of the MPP4 pin.
While this changes the DT compatibility, it is not considered to be a
problem since this pin is unlikely to be used for anything but
debugging purposes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was an off-by-one in the documentation of the ge1(txd[0-3])
pins, which is fixed by this commit. Since the driver was correct, and
the subnames are anyway not used in the DT binding itself, there is no
need to push this documentation fix for stable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the Ethernet txclkout pin to be
the same accross Marvell SoCs. It is worth mentioning that the DT
binding documentation of the Armada XP was wrong for MPP12: it said
the function was ge1(txd0), while it is in fact ge1(txclkout). It is
however not really a fix worth sending to stable since it does not
change the behavior, and the driver itself was correct.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit aligns the naming of the audio 'lrclk' pin accross Marvell
SoCs.
Since only the subname is changed, the DT backward compatibility is
not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of PCIe pins to use 'rstout' instead
of 'rstoutn' or 'rst-out'.
Since only the subnames are changed, DT compatibility is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the TDM pins accross the
different Marvell SoCs. Mainly it consists in:
* Removing the 'n' from signal names: 'intn' becomes 'int' and 'rstn'
becomes 'rst'
* Renaming the main name 'tdm2c' to 'tdm' on Armada 38x.
* Change the main name 'tdm-1' to 'tdm' for one of the pins of the
Armada XP
The last two changes affect DT compatibility, but since the TDM
interface is nowhere near being supported in mainline, it should not
be considered to be a serious problem at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All SoCs use "nand" to designate NAND pins, only Armada 39x is using
"nd", which is not consistent. This commit fixes that by renaming the
corresponding functions.
It also changes the subnames from rbn0/rbn1 to rb0/rb1, to respect the
convention used everywhere that we don't encode the 'n' part of signal
names.
While this commit changes the main name of function, therefore
potentially breaking the DT compatibility, this is not a problem since
Armada 39x is a brand new SoC which isn't used in production yet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit modifies the definition of the Device Bus interface pins
to be consistent accross SoCs. Especially, it removes the 'n'
indicators that we don't encode in the subnames of pins:
'dev(wen0)' becomes 'dev(we0)'
'dev(wen1)' becomes 'dev(we1)'
'dev(oen)' becomes 'dev(oe)'
etc.
In addition, it fixes the Armada 375 DT binding documentation, which
forgot to document the 'dev' function for MPP46, MPP57 and MPP63.
Since only the subnames are changed, this commit does not affect DT
compatibility.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to be consistent with the datasheet and some other SoCs, this
commit renames the SDIO pins of the Armada 39x from "sd" to "sd0".
While this changes the DT binding, this is not a problem since Armada
39x is a brand new SoC which isn't used in production yet (so now is
the right time to fix such things).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the naming of SATA related MPP functions consistent
accross SoCs by adjusting the Armada 39x definition to use "prsnt"
instead of "present".
Since only the subnames are changed, the DT binding is not modified at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the dram functions naming (both the name and
subname) consistent accross SoC, by using:
dram(vttctrl)
dram(deccerr)
in all Marvell SoCs.
Due to the change to the name, it changes the DT binding, but these
functions are not used by any in-tree Device Tree file, and are very
unlikely to be used by anyone.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The subnames are purely informative, but it's nicer when they match
accross SoCs. This commit adjusts the Armada 375, Armada 38x and
Armada 39x MPP definitions so that the subnames of the PTP pins match
the ones used on Armada XP and Kirkwood.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ce3ed59dcd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 5f597bb2be ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Combine the ChipIdea USB binding into a single document to reduce
duplication and fragmentation. This marks use of the old PHY bindings as
deprecated. Future compatible bindings should use generic PHY binding.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch was split out of Lubomir's original mailbox patch by Eric
Anholt, and the required properties documentation and examples have
been filled out more completely and updated for the driver being
changed to expose a single channel.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Craig McGeachie <slapdau@yahoo.com.au>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the LIS331DL sensor version. This is
a simple 8bit-only accelerometer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP: small set of misc. DT fixes; boot fix for THUMB2 kernel
- mediatek: PMIC fixes; DT fix for model name
- exynos: wakeup interupt fixes for 3250
- mvebu: revert mbus patch which broke DMA masters
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gSjy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add overview of tas2552's clock configuration and selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Saui
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Support configurable conversion mode through sysfs. So far, the
mode used was low-power, which is enabled by default now. Beside
that, the modes normal and high-speed are selectable as well.
Use the new device tree property which specifies the maximum ADC
conversion clock frequencies. Depending on the mode used, the
available resulting conversion frequency are calculated
dynamically.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids. All of the details
are in the shortlog and these patches have been in linux-next with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVzhIcACgkQMUfUDdst+ykY9ACg0HeMGzJAfsWSLiSsBRpDxFAr
ixAAnjOYj4Gv+XtAD4ZiOuMpaQaADntQ
=4uxU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
* clk-meson8b:
clk: meson8b: Add support for Meson8b clocks
clk: meson: Document bindings for Meson8b clock controller
clk: meson: Add support for Meson clock controller
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Using a fixed (by DTS) parent for clocks when turning on the power
domain may introduce issues in other drivers. For example when such
driver changes the parent during runtime and expects that he is the
only place of such change.
Do not rely on DTS providing the fixed parent for such clocks. Instead
before switching domain off, grab a current parent of a clock with
clk_get_parent().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds documentation for the devicetree bindings used by the
DT files of Hisilicon hi6220 SoC mobile platform.
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds two boolean properties to FMan Port.
FMan has 3 types of ports:
- 1G ports
By default, all ports support 1G rate
- 10G Ports
Port which use 10G hardware, and configured as 10G
- 10G Best effort ports
Ports which use 1G hardware, configured as 10G, in this case,
the rate is not guaranteed.
The new properties help to distinguish the different type of ports.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds the devicetree documentation for the ZTE
zx296702 I2S audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the devicetree documentation for the ZTE
zx296702 SPDIF audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A33 PIO has 7 ports which starts from PB and has two interrupt ports.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds documentation of device tree bindings for the
thermal sensor controller of hi6220 SoC.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This part just add necessary change to boot imx7d.
Update clock, pinctrl and gpt for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patchset include the huge update of extcon core and add the new one extcon
driver and fix minor isseu of extcon drivers.
Detailed description for patchset:
1. Update the extcon core.
- Modify the extcon device name on sysfs from device name name to 'extcon[X]'
as following because if same extcon device are included in H/W development board,
the one of the two device driver might be failed on the probe().
: /sys/class/extcon/[device name] -> /sys/class/extcon/extcon[X]
- Use the unique id for external connectors instead of legacy string name.
Previously, extcon used the string name to identify the type of external
connectors. This way have the many potential issues. So, extcon core define the
unique id for each external connectors as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
...
};
- Update tye prototype of extcon_register_notifier() by using the unique id
(enum extcon) of external connectors.
- Add extcon_get_edev_name() API to get the name of extcon device on extcon
client driver because the name is included in 'struct extcon_dev' and 'struct
extcon_dev' should be handled in only drivers/extcon directory. So. if extcon
client need the name of extcon device, they could use this function.
- Unify the jig/dock and MHL-TA cable name on extcon driver.
: JIG-{USB-ON|USB-OFF|UART-ON|UART-OFF} -> JIG
: Dock-{Smart|Desk|Audio|Card} -> DOCK
: MHL-TA -> TA
- Use the capital letter for the name of all external connectors.
- Remove the optional print_name() function pointer from struct extcon_dev to
maintain the consistent name of extcon device.
2. Add the new extcon-axp288.c extcon driver.
- The extcon-axp288.c driver support for AXP288 PMIC which has the BC1.2
charger detection capability. So this extcon driver can detect the
EXTCON_SLOW_CHARGER, EXTCON_CHARGE_DOWNSTREAM and EXTCON_FAST_CHARGER.
3. Update the extcon-arizona.c driver.
- Add support for selective detection mode when headphone detection.
- Apply HP clamps for WM8280
4. Clean-up the extcon core and drivers.
- Add manufactor information of each extcon device.
- Fix checkpatch warning and minor coding style on extcon.c.c
- Fix build break if GPIOLIB is not enabled on extcon-usb-gpiio.c.
- Set the direction of gpio when calling devm_gpiod_get() on extcon-usb-gpio.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Pc8L
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for v4.2
This patchset include the huge update of extcon core and add the new one extcon
driver and fix minor isseu of extcon drivers.
Detailed description for patchset:
1. Update the extcon core.
- Modify the extcon device name on sysfs from device name name to 'extcon[X]'
as following because if same extcon device are included in H/W development board,
the one of the two device driver might be failed on the probe().
: /sys/class/extcon/[device name] -> /sys/class/extcon/extcon[X]
- Use the unique id for external connectors instead of legacy string name.
Previously, extcon used the string name to identify the type of external
connectors. This way have the many potential issues. So, extcon core define the
unique id for each external connectors as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
...
};
- Update tye prototype of extcon_register_notifier() by using the unique id
(enum extcon) of external connectors.
- Add extcon_get_edev_name() API to get the name of extcon device on extcon
client driver because the name is included in 'struct extcon_dev' and 'struct
extcon_dev' should be handled in only drivers/extcon directory. So. if extcon
client need the name of extcon device, they could use this function.
- Unify the jig/dock and MHL-TA cable name on extcon driver.
: JIG-{USB-ON|USB-OFF|UART-ON|UART-OFF} -> JIG
: Dock-{Smart|Desk|Audio|Card} -> DOCK
: MHL-TA -> TA
- Use the capital letter for the name of all external connectors.
- Remove the optional print_name() function pointer from struct extcon_dev to
maintain the consistent name of extcon device.
2. Add the new extcon-axp288.c extcon driver.
- The extcon-axp288.c driver support for AXP288 PMIC which has the BC1.2
charger detection capability. So this extcon driver can detect the
EXTCON_SLOW_CHARGER, EXTCON_CHARGE_DOWNSTREAM and EXTCON_FAST_CHARGER.
3. Update the extcon-arizona.c driver.
- Add support for selective detection mode when headphone detection.
- Apply HP clamps for WM8280
4. Clean-up the extcon core and drivers.
- Add manufactor information of each extcon device.
- Fix checkpatch warning and minor coding style on extcon.c.c
- Fix build break if GPIOLIB is not enabled on extcon-usb-gpiio.c.
- Set the direction of gpio when calling devm_gpiod_get() on extcon-usb-gpio.c
It turns out that existing U-Boots will dereference NULL pointers
if the device tree does not have cell-index in the portal nodes.
No patch has yet been merged adding device tree nodes for this binding
(except a dtsi that has not yet been referenced), nor has any driver
yet been merged making use of the binding, so it's not too late to
change the binding in order to keep compatibility with existing
U-Boots.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Add Hardkernel Co., Ltd. to the list of device tree vendor prefixes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This adds documentation of device tree bindings for the
STM32 timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds documentation of device tree bindings for the
ARM System timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add DT bindings documentation for lpc3220-timer. This timer is
used as clocksource on many NXP platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing r8a7778-specific compatible value, which is already in
use since v4.1-rc1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVbEwwAAoJEEEQszewGV1zw5IQAMgEalCaSArXm/a12eogltuE
rGzJtP6MRwqLA4dGe+rOnUEsw2+jX1uBpUsBt7akBRbl2prRUpm89SJxZg8E5YpG
u2c+ODrh1lp4sRpAtKiMrLVx+hIjR4YFEa2cW0/OAJKG+4h1RXeQlXW3bw9q0qov
dO+M+NlcmWHyaJU9bNHYPZNYtG+9rVYY8kEK/LFe1xiY/VYC8KIe+gikR/R9WHI1
PZgAi1rARLeKAC7eThUDA+XnhzpxwYyqsxHsLV92l0l/cfly6DKCmZ1Zn9jk7v4b
L24jZ8OpHhJX5s//vsBmLxSobisuL8aLJDHCkrBmIb+geRsphOYmYTwmKdRJ2YkB
CyuxmvjdpKNiBIb8SGEKplrRaAexRfjXxX1GdNZNzdvIDo7T1hrM3/Fzo5TXxP61
Tgtu3I2Cwa3luDxFKaGlgldihvhUVPcAoBQUXyF57teWIh4iwTcrGZ3Li9kxTY32
ZvunTP/z8XjWRKFHv5KFCnnpxoQLDB/aHuv36H94hol5Nf95MC0EjGvBRM582z+u
1znExgtfSUt0BfqaxFgTieIu8RrQK0bxGcwBK6Okmv+j2BjTnE10ZuoqZSCaurOQ
QEkO336JNyYSwSu9Bxcwcx5x/qB+X5yuZLvmzhOp8Ld0omUngOqSpBtxdQQNQBK5
9qwI0QJ0Unc3rSgkJ6Ho
=IRmr
-----END PGP SIGNATURE-----
Merge tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500 and ARM SOC" from Linus Walleij:
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
* tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: define the backupram in the device tree
ARM: ux500: add board documentation
ARM: scu: document Snoop Control Unit DT bindings
The Allwinner SoCs have a handful of SRAM that can be either mapped to be
accessible by devices or the CPU.
That mapping is controlled by an SRAM controller, and that mapping might
not be set by the bootloader, for example if the device wasn't used at all,
or if we're using solutions like the U-Boot's Falcon Boot.
We could also imagine changing this at runtime for example to change the
mapping of these SRAMs to use them for suspend/resume or runtime memory
rate change, if that ever happens.
These use cases require some API in the kernel to control that mapping,
exported through a drivers/soc driver.
This driver also implement a debugfs file that shows the SRAM found in the
system, the current mapping and the SRAM that have been claimed by some
drivers in the kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The generic RZ CPG compatible value is mandatory, as the driver uses
only this value for matching. Document that this is a fallback that
must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic R-Car Gen2 CPG compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic MSTP gate clocks compatible value is mandatory, as the
driver uses only this value for matching. Document that this is a
fallback that must be present.
Also fix a typo (missing plural "s") in the compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic CPG DIV6 clock compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Using specific compatible string in binding doc to make the binding
more clear.
It's also used to avoid checkpatch warning in the future like follows:
WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented --
check ./Documentation/devicetree/bindings/
+ { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
total: 0 errors, 1 warnings, 18 lines checked
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the quirks and compatible string in sdhci-of-arasan.c
to support sdhci-arasan4.9a version of controller.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device tree binding documentation for nxp,lpc1850-uart.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
[added default values to optional properties]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix dts to match what the Linux kernel expects. This works around
touchscreen problems in 4.1 linux on Nokia n900.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "Documentation: bindings: Add DT bindings for ARM Juno boards" from Liviu Dudau:
* 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld:
Documentation: bindings: Add DT bindings for ARM Juno boards.
arm64: Add DT support for Juno r1 board.
arm64: Juno: Add GICv2m support in device tree.
arm64: Juno: Add memory mapped timer node
arm64: Juno: Split juno.dts into juno-base.dtsi and juno.dts.
arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.
CCI-500 provides 8 event counters which can count any of the
supported events independently. The PMU event id is a 9-bit
value made of two parts.
bits [8:5] - Source port
0x0-0x6 Slave Ports
0x8-0xD Master Ports
0xf Global Events to CCI
0x7,0xe Reserved
bits [0:4] - Event code (specific to each type of port)
The generic CCI-500 controlling interface remains the same with CCI-400.
However there are some differences in the PMU event counters.
- No cycle counter
- Upto 8 counters(4 in CCI-400)
- Each counter area is 64K(4K in CCI400)
- The counter0 starts at offset 0x10000 from the base of CCI
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlVmuqQACgkQykllyylKDCEKxgCgl/50lxDs3V9bRw5JUiN0ClM/
lCoAn2OfNpK5w/HmOw57erYuIA0rPQc8
=ulOE
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "arm: Xilinx Zynq dt patches for v4.2" from Michal Simek:
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
* tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: Use the zynq binding with macb
of: Add vendor prefix for Ceva
PCI: xilinx: Trivial fix in DT example
devicetree: cadence_ttc: Document binding for timer width
ARM: dts: zynq: Fix stdout-path and bootargs
ARM: dts: zynq: Add missing alias node for zybo and parallella
This patch adds device-tree bindings for ARM SMMUv3 IOMMU devices.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Toby Churchill Ltd is a global provider of assistive technology.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modern TTC implementations can extend the timer width to 32 bit. This
feature is not self identifying so the driver needs to be made aware
via device tree.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The commit df59fa7f4b "spi: orion: support armada extended baud
rates" made the assumptions that all the Armada SoCs supported the
same maximum frequency. However, according the hardware datasheet, the
maximum frequency supported by the Armada 370 SoC is tclk/4, for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
This patch introduces new compatible strings to handle all these
case. In order to be future proof a compatible was created for each
SoC even if currently some SoCs seem using the same IP.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for an external compontised DRM encoder. The external
encoder can be connected to tilcdc trough device tree graph binding.
The binding document for tilcdc has been updated. The current
implementation supports only tda998x encoder.
To be able to filter out the unsupported video modes the tilcdc driver
needs to hijack the external connectors helper functions. The tilcdc
installes new helper functions that are otherwise identical to
orignals, but the mode_valid() call-back check the mode first localy,
before calling the original call-back. The tilcdc dirver restores the
original helper functions before it is unbound from the external
device.
I got the idea and some lines of code from Jean-Francois Moine's
"drm/tilcdc: Change the interface with the tda998x driver"-patch.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove tilcdc slave support for tda998x driver. The tilcdc slave
support would conflicts with componentized use of tda998x.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the SSD1305 OLED controller.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 130X controllers are very similar from the configuration point of view.
The configuration registers for the SSD1305/6/7 are bit identical (except the
the VHCOM register and the the default values for clock setup register). This
patch unifies the init code of the controller and adds hardware specific
properties to DT that are needed to correctly initialize the device.
The SSD130X can be wired to the OLED panel in various ways. Even for the
same controller this wiring can differ from one display module to another
and can not be probed by software. The added DT properties reflect these
hardware decisions of the display module manufacturer.
The 'com-sequential', 'com-lrremap' and 'com-invdir' values define different
possibilities for the COM signals pin configuration and readout direction
of the video memory. The 'segment-no-remap' allows the inversion of the
memory-to-pin mapping ultimately inverting the order of the controllers
output pins. The 'prechargepX' values need to be adapted according to the
capacitance of the OLEDs pixel cells.
So far these hardware specific bits are hard coded in the init code, making
the driver usable only for one certain wiring of the controller. This patch
makes the driver usable with all possible hardware setups, given a valid hw
description in DT. If these values are not set in DT the default values,
as they are set in the ssd1307 init code right now, are used. This implies
that without the corresponding DT property "segment-no-remap" the segment
remap of the ssd130X controller gets activated. Even though this is not the
default behaviour according to the datasheet it maintains backward
compatibility with older DTBs.
Note that the SSD1306 does not seem to be using the configuration written to
the registers at all. Therefore this patch does not try to maintain these
values without changes in DT. For reference an example is added to the DT
bindings documentation that reproduces the configuration that is set in the
current init code.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Tested-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds the solomon prefix for Solomon Systech Limited.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A few late important fixes which have been pending
on mailing list due to my vacations.
The important fixes are a fix for DEPCMD and DGCMD
status bitfields on DWC3, a couple fixes for Renesas
USB Controller, one of which prevents a broken DT
binding from reaching v4.1-final, and an old fix for
s3c2410-udc where pullup logic was reversed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gNa5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.1-rc5
A few late important fixes which have been pending
on mailing list due to my vacations.
The important fixes are a fix for DEPCMD and DGCMD
status bitfields on DWC3, a couple fixes for Renesas
USB Controller, one of which prevents a broken DT
binding from reaching v4.1-final, and an old fix for
s3c2410-udc where pullup logic was reversed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
twl4030_charger currently finds the associated phy
using usb_get_phy() which will return the first USB2 phy.
If your platform has multiple such phys (as mine does),
this is not reliable (and reliably fails on the GTA04).
Change to use devm_usb_get_phy_by_node(), having found the
node by looking for an appropriately named sibling in
device-tree.
This makes usb-charging dependent on correct device-tree
configuration.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a compatible string to support for R-Car E2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>" in patch 2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds device tree binding documentation for the Broadcom BCM6358 LED controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds the device tree bindings for ktd2692 flash LEDs.
Add Optional properties of child node for Flash LED
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The ARM Server Base System Architecture[1] document describes a
generic UART which is a subset of the PL011 UART.
It lacks DMA support, baud rate control and modem status line
control, among other things.
The idea is to move the UART initialization and setup into the
firmware (which does this job today already) and let the kernel just
use the UART for sending and receiving characters.
We use the recent refactoring to build a new struct uart_ops
variable which points to some new functions avoiding access to the
missing registers. We reuse as much existing PL011 code as possible.
In contrast to the PL011 the SBSA UART does not define any AMBA or
PrimeCell relations, so we go with a pretty generic probe function
which only uses platform device functions.
A DT binding is provided with this patch, ACPI support is added in a
separate one.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uX2k
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
This driver manages Qualcomm CoreSight Replicator device, which
resides on the AMBA bus. Replicator has been made programmable to
allow software to turn of the replicator branch to sink that is not
being used. This avoids trace traffic to the unused/non-current sink
from causing back pressure that results in overflows at the source.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put in a blurb in the device tree bindings indicating that
coresight blocks may have an optional ATCLK.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some EHCI controllers have a Transaction Translator built into
the root hub. Support this feature in device tree when using
the ehci-platform driver by adding a feature flag for it.
This is needed to get USB working on NXP LPC18xx/43xx platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the datasheet found here:
http://www.ti.com/lit/ds/symlink/bq24257.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Following the addition of a Berlin ADC driver, this patch adds the
corresponding bindings documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge "Documentation: bindings: Add DT bindings for ARM Juno boards" from Liviu Dudau:
* 'for-upstream/juno-dts' of git://linux-arm.org/linux-ld:
Documentation: bindings: Add DT bindings for ARM Juno boards.
arm64: Add DT support for Juno r1 board.
arm64: Juno: Add GICv2m support in device tree.
arm64: Juno: Add memory mapped timer node
arm64: Juno: Split juno.dts into juno-base.dtsi and juno.dts.
arm64: Juno: Fix the GIC node address label and the frequency of FAXI clock.
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXvpAAAoJEAf03oE53VmQxx0IAMegPIH5rS0NIC+XmwpFnmre
L0bP0dRdKHS5uRxsZfD7F0WF61JiOuLzgX/rIIclnllvvKMPVW+CEs1KnfWVP33u
9FfFIErkGnYeJjs7Lj1j1lb9ESkJfqapMwTfl74mod8QFOT3cgXOiUu8pgHIp2cF
OTR6W5vkv1KoR8E0B4nGv9wZmRBeujtxW+2nIZZVcAglxfOHkJfqlfQ5wCQtdsnU
7K45r4WTbM632hIW5XA3OlzCuuIWs2Hr591aW8PY4KLMPB39HcCV/eTxJMGRbg1Q
4baSQ0xN+DhPfJary0Nc6Y2QXxZWb9y2ElGrqVMlbanCV7xaUGUGYrZ14heRvRs=
=ubIG
-----END PGP SIGNATURE-----
Merge tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Third batch of DT changes for 4.2" from Nicolas Ferre:
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: remove useless usb clock
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
USB: atmel: update DT bindings documentation
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iSye
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/cleanup
Merge "First batch of cleanup for 4.2" from Alexandre Belloni:
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
* tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
This adds support for the LG LB070WV8 7" 800x480 panel to the DRM simple
panel driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some platform specific parameter required to configure
the device like enable external control, DVS gpio etc.
Add DT parsing of such properties to make platform specific data.
Update DT binding doc accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates lpass bindings with apq8016 specific bindings.
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for the missing clocks, clock-names, reg and interrupts
properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT nodes should use the more specific adi,adxl345 and adi,adxl346
compatible values instead. As the ADXL346 is backward-compatible with
the ADXL345, ADXL346 nodes must list both adi,adxl346 and adi,adxl345,
in that order.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
exception of a single locking fix in the core code. All driver fixes are
for code that was merged recently. The Samsung stuff is mostly fixes
around suspend/resume, the Qualcomm fixes are for invalid hardware
configuration data and the Silicon Labs patches are fixes following
their move away from platform_data to Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yjsw
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
This patch adds a compatible string to support for R-Car E2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
the hardware node includes both clock and reset support, so it
is named as "car".
this patch implements Flexible clocks(mux, divider, gate), Selectable
clock(mux, divider, gate), root clock(gate),leaf clock(gate), others.
it also implements the reset controller functionality.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch allows to build the Kernel for Vybrid (VF6xx) SoC
when ARMv7-M CPU is selected. The resulting image runs on the
secondary Cortex-M4 core. This core has equally access to all
peripherals as the main Cortex-A5 core. However, there is no
resource control mechanism, hence when both cores are used
simultaneously, orthogonal device tree's are required.
The boot CPU is dependent on the SoC variant. The available
boards use mostly variants where the Cortex-A5 is the primary
and hence the boot CPU. Booting the secondary Cortex-M4 CPU
needs SoC specific registers written. There is no in kernel
support for this right now, a external userspace utility
called "m4boot" can be used to boot the kernel:
m4boot xipImage initramfs.cpio.lzo vf610m4-colibri.dtb
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C6Wl
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "Berlin DT changes for v4.2" from Sebastian Hesselbarth:
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
* tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin:
Documentation: bindings: update the berlin chip and system ctrl doc
Documentation: bindings: move the Berlin clock documentation
Documentation: bindings: move the Berlin pinctrl documentation
Documentation: bindings: move the Berlin reset documentation
Documentation: bindings: update the Berlin controllers documentation
Documentation: bindings: berlin: consider our dt bindings as unstable
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
USP is a general purpose serial port in SiRFSoC, which can work as SPI.
the most data flow of USP and pure SPI is same with main differences
in registers layout.
this patch moves registers layout to private data, and use flags to
differentiate other minor differences between prima2-spi, prima2-usp
and atlas7-usp for hardware configuration.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The at91rm9200 memory controller is not simply an SDRAM controller. It also
controls the EBI (External Bus Interface), the SMC (Static Memory Controller)and
the Burst Flash Controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.
The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.
So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".
The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.
There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.
For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.
The Device Tree can be written as following:
gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;
gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";
bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since 6397 is no need to support interrupt controller,
moving interrupt controller relate property to optional list.
Also adding mt8173 and mt8127 to bindings.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add device tree bindings for the pdata needed to configure
the Accessory Detect Mode select when Headphone detection.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
* readtest: the signal-handling code was clobbering the error codes we should
be handling/reporting in this test, rendering it useless. Noticed by Coverity.
* the common SPI NOR flash DT binding (merged for 4.1-rc1) is being revised,
so let's change that before 4.1 is minted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=13mb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes for 4.1:
- readtest: the signal-handling code was clobbering the error codes
we should be handling/reporting in this test, rendering it useless.
Noticed by Coverity.
- the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
revised, so let's change that before 4.1 is minted"
* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
mtd: readtest: don't clobber error reports
This documents the device tree bindings on the top level of
the Ux500 boards.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree bindings for the ARM Cortex-A5 and
Cortex-A9 Snoop Control Units.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mark "samsung,exynos3250-rtc" compatible as deprecated because it
duplicates the "samsung,s3c6410-rtc". Use "samsung,s3c6410-rtc" on
Exynos3250 and Exynos4415 boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Now that the rework to have one sub-node per device in the chip and
system controllers is done, their dedicated compatible can be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin clock documentation was part of the Marvell Berlin SoC
documentation because the Berlin clock configuration was inside the
chip controller. With the recent rework of the chip and system
controller handling (now all sub-devices of the soc and system
controller nodes are registred with simple-mfd, and each device has its
own sub-node), the documentation of the Berlin clock driver can be moved
to the generic clock documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin pinctrl documentation was part of the Marvell Berlin SoC
documentation because the Berlin pinctrl configuration was inside the
chip and the system controllers. With the recent rework of the chip and
system controller handling (now an MFD driver registers all sub-devices
of the two soc and system controller nodes and each device has its own
sub-node), the documentation of the Berlin pinctrl driver can be moved
to the generic pinctrl documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin reset documentation was part of the Marvell Berlin SoC
documentation because the Berlin reset configuration was inside the chip
controller. With the recent rework of the chip and system controller
handling (now an MFD driver registers all sub-devices of the two soc and
system controller nodes and each device has its own sub-node), the
documentation of the Berlin reset driver can be moved to the generic
reset documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
We're moving from a single node for multiple devices to a node with one
sub-node per sub-device, registered by simple-mfd. Update the
documentation to reflect the changes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Because the support of Marvell Berlin SoCs is still a work in progress,
add a statement to explicitly consider our device tree files and
bindings as unstable.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.
More information can be found on:
http://www.hitex.com/index.php?id=3212
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.
More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add notes to describe how some SoCs integrate this NAND core a little
differently, and so we define extra compatibility strings and register
resources/names.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
In commit 8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding"), we added a generic "nor-jedec" binding to catch all
mostly-compatible SPI NOR flash which can be detected via the READ ID
opcode (0x9F). This was discussed and reviewed at the time, however
objections have come up since then as part of this discussion:
http://lkml.kernel.org/g/20150511224646.GJ32500@ld-irv-0074
It seems the parties involved agree that "jedec,spi-nor" does a better
job of capturing the fact that this is SPI-specific, not just any NOR
flash.
This binding was only merged for v4.1-rc1, so it's still OK to change
the naming.
At the same time, let's move the documentation to a better name.
Next up: stop referring to code (drivers/mtd/devices/m25p80.c) from the
documentation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
This adds the clock binding documentation for the Marvell PXA1928 SOC.
The PXA1928 has 3 clock control blocks for different subsystems of the
chip.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Simplify the device tree support of the amd-xgbe driver by defining
the PHY-related resources within the ethernet device node. The support
provides backwards compatibility with the original way.
Update the driver version to 1.0.2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for nxp,lpc1850-dwmac.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KpAt
-----END PGP SIGNATURE-----
Merge tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi into next/dt
Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:
* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
ARM: bcm2835: dt: Add the mailbox to the device tree
ARM: bcm2835: dt: Fix i2c0 node name
ARM: bcm2835: dt: Use pinctrl header
ARM: bcm2835: dt: Add header file for pinctrl constants
ARM: bcm2835: dt: Add root properties for Raspberry Pi
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OdRc
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
Merge "Device Tree changes" from Florian Fainelli:
New devices:
- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
WZR-1750DHP
- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U
New peripheral support:
- Brian adds Device Tree nodes for the Broadcom NAND controller found on
BCM7xxx, BCM63138 and Cygnus SoCs
- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
BCM7xxx
- I add the Device Tree nodes and bindings documents for bringing-up secondary
CPUs and timer/syscon-reboot on BCM63138
* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC56U
ARM: BCM5301X: Add DT for Asus RT-AC68U
ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
ARM: dts: brcmstb: add nodes for SATA controller and PHY
ARM: dts: cygnus: Enable NAND support for Cygnus
ARM: bcm63138: add NAND DT support
ARM: bcm7445: add NAND to DTS
ARM: BCM5301X: Add DT for SmartRG SR400ac
ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
ARM: dts: BCM63xx: Add SMP nodes and required properties
Documentation: DT: Document SMP DT nodes and properties for BCM63138
ARM: dts: BCM63xx: Add PMB busses nodes
Documentation: DT: Add Broadcom BCM63138 PMB binding
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds root compatible properties for the following boards:
- Raspberry Pi Model A
- Raspberry Pi Model A+
- Raspberry Pi Model B
- Raspberry Pi Model B (no P5)
- Raspberry Pi Model B rev2
- Raspberry Pi Model B+
- Raspberry Pi Compute Module
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the prefix is already in use, we need to add it in the
vendor list.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The binding uses assigned-clock-parents when it should use
assigned-clock-rates. Furthermore, the part that describes how
they relate to the assigned-clocks property is not clear about
what is related. Correct and clarify this part of the binding.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
A timer node and a syscon-reboot node are required for software reboot
to work on BCM63138, document these two nodes in the platform binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add optional DT properties to set open delay, sample delay and number
of averages per sample for each adc step. Open delay, sample delay
and averaging are some of the parameters that affect the sampling rate
and accuracy of the sample. Making these parameters configurable via
DT will help in balancing speed vs accuracy.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add binding documentation for the additional nodes and properties
required to get the secondary CPU online on the BCM63138 SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a Device Tree binding for the Broadcom BCM63138 Processor Monitor
Bus, which is an internal bus used to access different power and reset
signals within a BCM63138 System-on-a-Chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The RAM code is used by the memory and external memory controllers to
determine which set of timings to use for memory frequency scaling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yv05
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-ramcode' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "ARM: tegra: RAM code access for v4.2-rc1" from Thierry Reding:
The RAM code is used by the memory and external memory controllers to
determine which set of timings to use for memory frequency scaling.
* tag 'tegra-for-4.2-ramcode' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Add RAM code reader helper
of: Document long-ram-code property in nvidia,tegra20-apbmisc
Just a couple of trivial cleanups such as a typofix and conversion of
hexadecimal numbers to all lower-case in DTS files for consistency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OrUc
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
Merge "ARM: tegra: Cleanup patches for v4.2-rc1" from Thierry Reding:
Just a couple of trivial cleanups such as a typofix and conversion of
hexadecimal numbers to all lower-case in DTS files for consistency.
* tag 'tegra-for-4.2-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Fix typo (reset -> rest) in comment
ARM: tegra: Use lower-case hexadecimal digits
Add the list of regulators for AXP22x to the DT bindings.
This includes the names and supply names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add AXP221 to the list of supported devices.
Also replace any mention of AXP20x in the document with a
generic "PMIC".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WM8741 DAC supports several differential output modes (stereo,
stereo reversed, mono left, mono right). Add platform data and DT
bindings to configure it.
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This property contains a phandle to the EMC driver that is needed by the
EMC clock to request the EMC driver to do its part of the clock change
sequence.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock needs some extra information for changing its rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This pull request contains only the changes needed to support the SMP on
the Allwinner A23.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RNcV
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Merge "Allwinner core additions for 4.2" from Maxime Ripard:
This pull request contains only the changes needed to support the SMP on
the Allwinner A23.
* tag 'sunxi-core-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: Add SMP support for the Allwinner A23
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6TQo
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT additions for 4.1, take 1" from Maxime Ripard:
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
* tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (84 commits)
ARM: sunxi: dt: Split the SPI pinctrl groups
ARM: sunxi: dt: Fix whitespace errors
ARM: sunxi: DT: Fix lines over 80 characters
ARM: sunxi: dt: Remove the FSF address
ARM: sunxi: dts: split IR pins for A10 and A20
ARM: sun7i: dt: Add new MK808C device
ARM: dts: sun6i: Set PLL6 as parent to AHB1 clock in AHB1 clock node
ARM: dts: sunxi: Update ahb clocks for sun5i and sun7i
ARM: dts: sun7i: Add dts file for the Jesurun Q5 top set box
ARM: dts: sun5i: Enable touchscreen on Utoo P66
ARM: dts: sun7i: Add dts file for the Orangepi mini SBC
ARM: dts: sun7i: Add dts file for the Orangepi SBC
ARM: dts: sun7i: Add A20 SRAM and SRAM controller
ARM: dts: sun5i: Add A13 and A10s SRAM and SRAM controller
ARM: dts: sun4i: Add A10 SRAM and SRAM controller
ARM: dts: sun5i: Add broken-hpi property for Utoo-P66 eMMC
ARM: sun8i: dt: Enable A23 SMP support
ARM: dts: sun6i: Add cpu thermal zones to dtsi
ARM: dts: sun6i: Add cpu clock reference and operating points to dtsi
ARM: sunxi: DT: Add stdout-path property
...
Since commit 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.
Fix the binding documentation so the property is properly specified.
Fixes: 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVT9fTAAoJEHm+PkMAQRiGrbYH/276n6aKSORO0B6DrEnebu8Y
oxfJeacg90/N5aLx/B5GEplO24uTENaAfB342WkexziXdY+7P02J0Y36eSh5WiL2
qcL+gkiZVaApZIjVeO/y2ByL7nLprPeIsxl5gGLhI+qYYMaQ8gtzxC7sDLnNqjPS
w8WYQB7LdWeGFqcuvySEX2C6Q62aHpZWoSsV3LYdrfoDJz2lv1DJrOpRhqXPagl7
oX1c1CWQ4yWdFf9xm8vaiZw7EskxEnObQm7n7vWlZ0xAhXZ/3a7bPdc+fj2V+nve
xjZV/EhEL0u3ME86bVtcqbO3lgMjivyWHjQglCwG6keS+iIHkL0xMlQabkrFJhw=
=LGDf
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc3' into patchwork
Linux 4.1-rc3
* tag 'v4.1-rc3': (381 commits)
Linux 4.1-rc3
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
m32r: make flush_cpumask non-volatile.
mnt: Fix fs_fully_visible to verify the root directory is visible
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
...
This defines a new compatible option for MFD devices "simple-mfd" that will
make the OF core spawn child devices for all subnodes of that MFD device.
It is optional but handy for things like syscon and possibly other
simpler MFD devices.
Since there was no file to put the documentation in, I took this opportunity
to make a small writeup on MFD devices and add the compatible definition
there.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Devicetree <devicetree@vger.kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A few patches have come up since the merge window. The largest one is a
rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1
is now listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lVQn
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few patches have come up since the merge window. The largest one is
a rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1 is now
listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
...
Add "cdns,zynqmp-gem" to be used for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wyz7
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for the 4.2 cycle
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
The DRA7x has more peripherals with DMA requests than the sDMA can handle:
205 vs 127. All DMA requests are routed through the DMA crossbar, which can
be configured to route selected incoming DMA requests to specific request
line of the DMA controller.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA routers are transparent devices used to mux DMA requests from
peripherals to DMA controllers. They are used when the SoC integrates more
devices with DMA requests then their controller can handle.
DRA7x is one example of such SoC, where the sDMA can hanlde 128 DMA request
lines, but in SoC level it has 205 DMA requests.
The of_dma_router will be registered as of_dma_controller with special
xlate function and additional parameters. The driver for the router is
responsible to craft the dma_spec (in the of_dma_route_allocate callback)
which can be used to requests a DMA channel from the real DMA controller.
This way the router can be transparent for the system while remaining generic
enough to be used in different environments.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add the TI drv2665 piezo haptic driver. This haptics IC requires the data
to be streamed to the FIFO for continuous output.
Datasheet can be found at:
http://www.ti.com/product/drv2665
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the introduction of clk-si5351 the way we should deal with DT provided
clocks has changed from indexed to named clock phandles. Amend the binding
documentation to reflect named clock phandles by clock-names property.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add small documentation for GTM601 UMTS modem audio interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Open firmware is already using the serial-number property for passing the
device's serial number from the bootloader to the kernel. In addition, lshw
already has support for scanning this property.
The serial number is a string that somewhat represents the device's serial
number. It might come from some form of storage (e.g. an eeprom) and be
programmed at factory-time by the manufacturer or come from identification
bits available in e.g. the SoC (note that the soc_id property in the SoC bus
should hold a full account of those bits).
The serial number is taken as-is from the bootloader, so it is up to the
bootloader to define where the serial number comes from and what length it
should be. Some use cases for the serial number require it to have a maximum
length (e.g. for USB serial number) and some other cases imply more restrictions
on what the serial number should look like (e.g. in Android, the ro.serialno
property is usually a 16-bytes (plus one null byte) representation of a 64 bit
number).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use 'clock-controller' and 'power-controller' as node names in the
examples rather than the specific names of the units.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There is a subtle typo phys-names should be phy-names. Using the
current example means you don't have working usb (as you fail to
obtain the phys). Also update the example to use the generic phy
type constants which are now used for miphy28.
Additionally also remove the unnecessary new line in the example.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uart -> serial
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
The LSM303DLH accelerometer/magnetometer has a different
device identification method than using register 0x0f, instead
three registers contain a magic value. We rely on WhoAmI
to be zero for this variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mtk 8250 needs two clocks, one for providing the baudrate and
one that needs to be enabled for register accesses. The latter has
not been supported, this patch adds support for it. It is optional
for now since not all SoCs provide a bus clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 52bec4ed4e("serial: sirf: add a new uart type
support").
we misunderstood the clock dependency in atlas7. Actually involved
several clocks are in a tree structure. we still only need to take
the leaf clock node for BT uarts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since SCLK, MISO and MOSI are the only mandatory signals at Zynq's SPI
interfaces, SS0, SS1 and SS2 have to be configured separately as they may
be used as simple GPIO lines.
This, of course, has to be considered in the devicetree, so pin controller
configuration for e.g. an SPI0 using SS0 and SS1 only might look like the
following snippet (derived from the example of chapter "17.5.3
MIO/EMIO" Routing of Zynq-7000 TRM UG585). So MIO20 can now be used
as GPIO instead of being occupied by SPI0 SS2 function. Note the separate
pinmux function for the slave select signals:
pinctrl_spi0_default: spi0-default {
mux_spi {
function = "spi0";
groups = "spi0_0_grp";
};
mux_ss {
function = "spi0_ss";
groups = "spi0_0_ss0_grp", "spi0_0_ss1_grp";
}
conf-output {
pins = "MIO16", "MIO21";
slew-rate = <0>;
bias-disable;
low-power-disable;
io-standard = <1>;
};
conf-input {
pins = "MIO17";
slew-rate = <0>;
bias-high-impedance;
low-power-disable;
io-standard = <1>;
};
conf-select {
pins = "MIO18", "MIO19";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
pinctrl_gpio0_default {
mux {
function = "gpio0";
groups = "gpio0_20_grp"
};
conf {
pins = "MIO20";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the binding documentation for the apmixedsys, perisys and
infracfg controllers found on Mediatek SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Document the bindings for abracon,abx80x and related compatibles.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MC driver needs some timing-specific information to program the EMEM
during a rate change of the EMC clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
