In order to migrate the bcm_sf2 driver over to the b53 driver for most
VLAN/FDB/bridge operations, we need to add support for the "join all
VLANs" register and behavior which allows us to make a given port join
all VLANs and avoid setting specific VLAN entries when it is leaving the
bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout
and introduce a helper function: is58xx() which checks for both of these
IDs for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a device entry for the Broadcom BCM7445 integrated switch
currently backed by bcm_sf2.c. Since this is the latest generation, it
has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow drivers to override specific dsa_switch_driver
callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids
having to expose this structure to glue drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without it, a mv88e6131 switch will not forward incoming unicast
packets to the CPU port.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPU method of accessing PHYs makes use of a timer. Make sure this
timer is deleted before unloading the driver.
Reported-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging on the CPU port. New devices
support both DSA and EDSA. The driver needs to tell the core the tag
protocol to use, and configure the switch for what is available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces every MDIO direct or indirect access with the new
generic mv88e6xxx_phy_* routines.
This allows us to get rid of the mv88e6xxx_mdio_{read,write}_{,in}direct
and {_,}mv88e6xxx_mdio_page_{read,write} functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mv88e6xxx_phy_page_{read,write} routines and use them to access the
SerDes PHY device registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old chips use a direct access to the PHY devices registers. Next chips
have a PHY Polling Unit (PPU) which needs to be disabled before
accessing PHY registers. Newer chips have an indirect access to the PHY
devices so that disabling the PPU is not necessary.
Introduce a new phy_ops structure in the chip to describe the required
PHY access routines.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the presence of the Global2 SMI PHY registers, used to
indirectly access the internal SMI devices registers on some chips.
Also temporarily forward declare mv88e6xxx_g2_smi_phy_{read,write} to
use them in mv88e6xxx_mdio_{read,write}_indirect, before getting rid of
the later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of SMI Command and Data registers
used to indirectly access internal SMI devices registers when the switch
SMI address is not zero.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no locked version of the wait routine anymore, rename
the _ prefixed version and make it use the new read API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner and .bus fields since module_spi_driver() is used
which set them automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57d3231057 ("net: dsa: mv88e6xxx: fix style issues")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53_io_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For pdata == null the code leaves with an error.
There is no need to check the condition again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we cannot complete bcm_sf2_sw_setup() for any reason, and we
go to the out_unmap label, but the MDIO bus has not been registered yet,
we will hit the BUG condition in drivers/net/phy/mdio_bus.c about the
bus not being registered. Fix this by dedicating a specific lable for
when we fail after the MDIO bus has been successfully registered.
Fixes: 461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last usage of the locked mv88e6xxx_reg_read function with
a new mv88e6xxx_port_read helper, useful later for chips with different
port registers base address.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family of switches and compatibles provide a 8-bit address and
16-bit data access to an optional EEPROM.
Newer chip such as the 6390 family slightly changed the access to 16-bit
address and 8-bit data.
This commit cleans up the EEPROM access code for 16-bit access and makes
it easy to eventually introduce future support for 8-bit access.
Here's a list of notable changes brought by this patch:
- provide Global2 unlocked helpers for EEPROM commands
- remove eeprom_mutex, only reg_lock is necessary for driver functions
- eeprom_len is 0 for chip without EEPROM, so return it directly
- the Running bit must be 0 before r/w, so wait for Busy *and* Running
- remove now unused mv88e6xxx_wait and mv88e6xxx_reg_write
- other than that, the logic (in _{get,set}_eeprom16) didn't change
Chips with an 8-bit EEPROM access will require to implement the
8-suffixed variant of G2 helpers and the related flag:
#define MV88E6XXX_FLAGS_EEPROM8 \
(MV88E6XXX_FLAG_G2_EEPROM_CMD | \
MV88E6XXX_FLAG_G2_EEPROM_ADDR)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only reg_lock is necessary now and phy_mutex is dead. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA driver function to configure the bridge ageing time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips from (88E6060 to 88E6390) have a ATU Control
register containing bits 11:4 to configure an ATU Age Time quotient.
However the coefficient used to calculate the ATU Age Time vary with the
models. E.g. 88E6060, 88E6352 and 88E6390 use respectively 16, 15 and
3.75 seconds.
Add a age_time_coeff to the info structure to handle this and a Global 1
helper to set the default age time of 5 minutes in the setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability flags to describe the presence of Ingress Rate Limit unit
registers and an helper function to clear it.
In the meantime, fix a few harmless issues:
- 6185 and 6095 don't have such registers (reserved)
- the previous code didn't wait for the IRL operation to complete
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags and helpers to describe the presence of Priority Override
Table (POT) related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Cross-chip Port VLAN Table (PVT)
related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches such as 88E6185 as 3 Switch MAC registers in Global 1. Newer
chips such as 88E6352 have freed these registers in favor of an indirect
access in a Switch MAC/WoL/WoF register in Global 2.
Explicit this difference with G1 and G2 helpers and flags.
Also, note that this indirect access is a single-register which doesn't
require to wait for the operation to complete (like Switch MAC, Trunk
Mapping, etc.), in contrary to multi-registers indirect accesses with
several operations and a busy bit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches provide a Rsvd2CPU mechanism used to choose which of the
16 reserved multicast destination addresses matching 01:80:c2:00:00:0x
should be considered as MGMT and thus forwarded to the CPU port.
Other switches extend this mechanism to also configure as MGMT the
additional 16 reserved multicast addresses matching 01:80:c2:00:00:2x.
This mechanism is exposed via two registers in Global 2, and an Rsvd2CPU
enable bit in the management register.
Newer chip (such as 88E6390) has replaced these registers with a new
indirect MGMT mechanism in Global 1.
The patch adds two MV88E6XXX_FLAG_G2_MGMT_EN_{0,2}X flags to describe
the presence of these Global 2 registers. If 88E6390 support is added, a
MV88E6XXX_FLAG_G1_MGMT_CTRL flag will be needed to setup Rsvd2CPU.
Note: all switches still support in parallel the ATU Load operation with
an MGMT Entry State to forward such frames in a less convenient way.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Trunk Mask and Trunk Mapping registers are two Global 2 indirect
accesses to trunking configuration.
Add helpers for these tables and simplify the Global 2 setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Device Mapping register is an indirect table access.
Provide helpers to access this table and explicit the checking of the
new DSA_RTABLE_NONE routing table value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the setup of Global 1 and Global 2 internal SMI devices and add
a flag to describe the presence of this second registers set.
Also rearrange the G1 setup in the registers order.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 88E6xxx Marvell switches (even the old not supported yet 88E6060)
have at least an ATU, per-port STP states and VLAN map, to run basic
switch functions such as Spanning Tree and port based VLANs.
Get rid of the related MV88E6XXX_FLAG_{ATU,PORTSTATE,VLANTABLE} flags,
as they are defaults to every chip.
This enables STP on 6185 and removes many inconsistencies on others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/b53/b53_srab.c: In function 'b53_srab_probe':
>> drivers/net/dsa/b53/b53_srab.c:388:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
pdata->chip_id = (u32)of_id->data;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc produces a warning for correct code
in this driver:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:107:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read48':
drivers/net/dsa/b53/b53_mmap.c:91:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c:83:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 16) | lo;
I have seen the warning before and at the time thought I had fixed
it with 55e7f6abe1 ("dsa: b53: fix big-endian register access"),
however it now came back in a different randconfig build that happens
to have different inlining decisions in the compiler.
The mistake that gcc makes here is that it thinks the second call to
readl() might fail because the address 'reg + 4' is not a multiple
of four despite having knowing that 'reg' itself is a multiple of four.
By open-coding the two reads without the redundant alignment check,
we can avoid the warning and produce slightly better object code, but
get slightly longer source code instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.
Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.
Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.
In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid 88E6352 entry with 88E6XXX, maintained by
Andrew and myself.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a typo we would always be using the MIB counter width of the
first element of the counter array instead of the current element, and
we would always be accessing the register statistics with a 64-bits
read, while some could be 32-bits. This got unnoticed in testing with
MDIO and SRAB which tolerate doing this, but testing with the SPI bus
revealed bogus values being returned. Fix this by using the proper
iterator here.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the SMI address of the switch chip is zero, the chip assumes to be
the only one on the SMI master bus and thus responds to all its known
SMI devices addresses (port registers, Global2, etc.)
When its SMI address is not zero, some chips (e.g. 88E6352) use an
indirect access through two SMI Command and Data registers.
Other models (e.g. 88E6060) using less than 16 internal SMI addresses
always use a direct access.
Add a capability flag to describe chips supporting the (indirect)
Multi-chip Addressing Mode, and a low-level API to access the registers
via SMI.
Other accesses (like Ethernet management frames) may be added later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch ID is located at address 0x3 of every Port Registers bank.
But not all Marvell switches have their Port Registers SMI Addresses
starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0.
Add this data in the info structure and use it in the detection code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the chip structure, pass it a compatible info pointer.
The compatible info structure will be used later to describe how to
access the switch registers and where to read the switch ID.
For the standard MDIO probe, get it from the device node data. For the
legacy DSA driver probing, pass it the 88E6085 info.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the common detection code which assigns the info structure to
the chip given the read switch ID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper function to isolate SMI specific assignments and checks.
This function will later help choosing the different SMI accesses based
of the compatible info.
Since the chip structure is already allocated in the legacy probe, use
the mv88e6xxx_reg_read access routine instead of __mv88e6xxx_reg_read.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper function to allocate the chip structure at the beginning
of the probe functions. It will be used to initialize the SMI access.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip smi_mutex mutex is used to protect the access to the internal
switch registers, not only the Multi-chip Addressing Mode, as commented.
Since we will isolate SMI-specific pieces of code, avoid the confusion
now by renaming smi_mutex to reg_lock. No functional changes here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_table array and the mv88e6xxx_lookup_info function are
static, so remove the table and size arguments from the lookup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the optional variant to get the reset GPIO line, instead of checking
for the -ENOENT error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mixed assignments, allocations and registrations in the probe code
make it hard to follow the logic and figure out what is DSA or chip
specific.
Extract the struct dsa_switch related code in a simple
mv88e6xxx_register_switch helper function.
For symmetry in the code, add a mv88e6xxx_unregister_switch function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO device probe and remove functions are respectively incrementing
and decrementing the bus refcount themselves. Since these bus level
actions are out of the device scope, remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MDIO probing function, dev is already assigned to &mdiodev->dev
and np is already assigned to mdiodev->dev.of_node, so use them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip->ds and ds->slave_mii_bus assignments are common to both legacy
and new MDIO probing and are already done in the later setup code.
Remove the duplicated assignments from the MDIO probing code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 5 style problems reported by checkpatch:
WARNING: suspect code indent for conditional statements (8, 24)
#492: FILE: drivers/net/dsa/mv88e6xxx.c:492:
+ if (phydev->link)
+ reg |= PORT_PCS_CTRL_LINK_UP;
CHECK: Logical continuations should be on the previous line
#1318: FILE: drivers/net/dsa/mv88e6xxx.c:1318:
+ oldstate == PORT_CONTROL_STATE_FORWARDING)
+ && (state == PORT_CONTROL_STATE_DISABLED ||
CHECK: multiple assignments should be avoided
#1662: FILE: drivers/net/dsa/mv88e6xxx.c:1662:
+ vlan->vid_begin = vlan->vid_end = next.vid;
WARNING: line over 80 characters
#2097: FILE: drivers/net/dsa/mv88e6xxx.c:2097:
+ const struct switchdev_obj_port_vlan *vlan,
WARNING: suspect code indent for conditional statements (16, 32)
#2734: FILE: drivers/net/dsa/mv88e6xxx.c:2734:
+ if (mv88e6xxx_6352_family(ps) || mv88e6xxx_6351_family(ps) ||
[...]
+ reg |= PORT_CONTROL_EGRESS_ADD_TAG;
total: 0 errors, 3 warnings, 2 checks, 3805 lines checked
It also rebases and integrates changes sent by Ben Dooks [1]:
The driver has a number of functions that are not exported or
declared elsewhere, so make them static to avoid the following
warnings from sparse:
drivers/net/dsa/mv88e6xxx.c:113:5: warning: symbol 'mv88e6xxx_reg_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:167:5: warning: symbol 'mv88e6xxx_reg_write' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:231:5: warning: symbol 'mv88e6xxx_set_addr' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:367:6: warning: symbol 'mv88e6xxx_ppu_state_init' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3157:5: warning: symbol 'mv88e6xxx_phy_page_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3169:5: warning: symbol 'mv88e6xxx_phy_page_write' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3583:26: warning: symbol 'mv88e6xxx_switch_driver' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3621:5: warning: symbol 'mv88e6xxx_probe' was not declared. Should it be static?
[1] http://patchwork.ozlabs.org/patch/632708/
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.
Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.
Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the switch driver register its own MDIO bus. This allows for an
mdio property in the device tree, with child nodes for phys, which
can be referenced via phandles, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch implements a generic MDIO bus, which could host more than
PHYs. It is conventional to use _mdio_ or _mii_ in the function name,
so rename them. Also postfix make the historically first read/write
function with _direct, to help distinguish it from _indirect and _ppu.
While touching these functions, remove some of the _ prefixes, which
we are deprecating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The merged driver no longer offers the option to use DSA tagging. So
remove the code to setup the switch to do DSA tagging and hard code
the use of EDSA.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>y
Signed-off-by: David S. Miller <davem@davemloft.net>
The new binding will not have a chip data structure, it will place the
routing directly into the switch structure. To enable backwards
compatibility, copy the routing from the chip data into the switch
structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a maximum of four switches, the size of the routing table is the
same as the pointer to it. Removing it makes the code simpler.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are going to be more per-port members added to the switch
structure. So add a port structure and move the netdev into it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge code defers the switchdev port state setting, there
is no need to defer the port STP state change within the mv88e6xxx code.
Thus get rid of the driver's bridge work code.
This also fixes a race condition where the DSA layer assumes that the
bridge code already set the unbridged port's STP state to Disabled
before restoring the Forwarding state.
As a consequence, this also fixes the FDB flush for the unbridged port
which now correctly occurs during the Forwarding to Disabled transition.
Fixes: 0bc05d585d ("switchdev: allow caller to explicitly request attr_set as deferred")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch can export an attached EEPROM using the standard ethtool API.
However the switch itself cannot determine the size of the EEPROM, and
multiple sizes are allowed. Thus a device tree property is supported
to indicate the length of the EEPROM. Parse this property during
device probe, and implement a callback function to retrieve it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow Marvell switches to be mdio devices. Currently the driver just
allocate the private structure and detects what device is on the
bus. Later patches will make them register with the DSA framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other DSA drivers use _drv_ in there DSA probe function name, thus
allowing for a true linux driver probe function to use the
conventional name. Make mv88e6xxx fit this pattern.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By initialising immediately it, we don't run the danger of using it
before it is initialised.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a STU (per VLAN port state database). Add a new
capability flag to switches info, instead of checking their family.
Also if the 6165 family has an STU, it must have a VTU, so add the
MV88E6XXX_FLAG_VTU to its family flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both VTU and STU operations use the same routine to access their
(common) data registers, with a different offset.
Add VTU and STU specific read and write functions to the data registers
to abstract the required offset.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.
This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a shared mv88e6xxx_setup function to the drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models setup the GLOBAL_CONTROL_2 register with slightly
differences.
Since the cascade mode is valid even in a single chip setup, factorize
such configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch drivers configure the GLOBAL_MONITOR_CONTROL register with
slightly changes.
Assume the setup of the upstream port, and configure it as the port to
which ingress and egress and ARP monitor frames are to be sent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6131 switch models have a Core Tag Type register. Their setup code
is setting it to 0x8100, which is the reset default.
Drop this specific part which is correctly configured on reset anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure ds is actually needed in very few places,
mostly during setup of the switch. The private structure ps is however
needed nearly everywhere. Pass ps, not ds internally.
[vd: rebased Andrew's patch.]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
ps->id is not needed anymore, so remove it as well as the related
defined values.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the number of databases to the info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the ps->num_ports variable in favor of a new member of the info
structure. This removes the need to assign it at setup time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an mv88e6xxx_family enum to the info structure for better family
indentification.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new switch info structure which is meant to store switch models
static information, such as product number, name, number of ports,
number of databases, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the switch ID only once, at probe time, to avoid multiple read
accesses and MII bus checking.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having a special case for the revision when probing
a switch model. The code gets cluttered with unnecessary defines, and
leads to errors when code such as mv88e6131_setup compares
PORT_SWITCH_ID_6131_B2 to ps->id which masks the revision.
Drop every revision definition, and lookup only the product number.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver assigns ps->ds even though it gets assigned in the shared
mv88e6xxx_setup_common function. Kill redundancy.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros hide a ds variable and a return statement on error, which
can lead to locking issues. Kill them off.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware cross-chip bridging to work, user ports *and* DSA ports
need to share a common address database, in order to switch a frame to
the correct interconnected device.
This is currently working for VLAN filtering aware systems, since Linux
will implement a bridge group as a 802.1Q VLAN, which has its own FDB,
including DSA and CPU links as members.
However when the system doesn't support VLAN filtering, Linux only
relies on the port-based VLAN to implement a bridge group.
To fix hardware cross-chip bridging for such systems, set the same
default address database 0 for user and DSA ports, instead of giving
them all a different default database.
Note that the bridging code prevents frames to egress between unbridged
ports, and flushes FDB entries of a port when changing its STP state.
Also note that the FID 0 is special and means "all" for ATU operations,
but it's OK since it is used as a default forwarding address database.
Fixes: 2db9ce1fd9 ("net: dsa: mv88e6xxx: assign default FDB to ports")
Fixes: 466dfa0770 ("net: dsa: mv88e6xxx: assign dynamic FDB to bridges")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-chip systems, DSA Tag ports must learn SA addresses in order to
correctly switch frames between interconnected chips.
This fixes cross-chip hardware bridging in a VLAN filtering aware
system, because a bridge group gets implemented as an hardware 802.1Q
VLAN and thus DSA and user ports share the same FDB.
Fixes: 4c7ea3c079 ("net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking a port generates an hardware interrupt when a new SA address is
received. This enables CPU directed learning, which is needed for 802.1X
MAC authentication.
To disable automatic learning on a port, the only configuration needed
is to set its Port Association Vector to all zero.
Clear PAV when SA learning should be disabled instead of locking a port.
Fixes: 4c7ea3c079 ("net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_lookup_name() returns the model name of a switch at a given
address on an MII bus. Using mii_bus to identify the bus rather than
the host device is more logical, so change the parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phys in phys_port_mask suggests this mask is about PHYs. In fact,
it means physical ports. Rename to enabled_port_mask, indicating
external enabled ports of the switch, which is hopefully less
confusing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the function called from the DSA to perform a probe for the
switch. This makes the normal _probe() name available for a standard
Linux device driver probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than looking up the mii bus and address every time, do it once
at probe, and keep it in the private structure. Centralise this probe
code in mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the switch devices have a dev pointer, make use of it for allocating
the drivers private data structures using a devm_kzalloc().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing a device structure to the switch devices, it allows them
to use devm_* methods for resource management.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.
Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.
Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.
Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.
In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding support for bridge operations, FDB operations, and optionally
VLAN operations (for 802.1Q and VLAN filtering aware systems), the
switch bridges ports correctly, the CPU is able to populate the hardware
address databases, and thus hardware bridging becomes functional within
the 88E6185 family of switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6185 switch also has a MapDA bit in its Port Control 2 register.
When this bit is cleared, all frames are sent out to the CPU port.
Set this bit to rely on address databases (ATU) hits and direct frames
out of the correct ports, and thus allow hardware bridging.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 family of devices has only 256 address databases. Their 8-bit
FID for ATU and VTU operations are split into ATU Control and ATU/VTU
Operation registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell switch chips have different number of address databases.
The code currently only supports models with 4096 databases. Such switch
has dedicated FID registers for ATU and VTU operations. Models with
fewer databases have their FID split in several registers.
List them all but only support models with 4096 databases at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only switch families with 4096 address databases have dedicated FID
registers for ATU and VTU operations.
Factorize the access to the GLOBAL_ATU_FID register and introduce a
mv88e6xxx_has_fid_reg() helper function to protect the access to
GLOBAL_ATU_FID and GLOBAL_VTU_FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a mv88e6xxx_has_stu() helper to protect the access to the
GLOBAL_VTU_SID register, instead of checking switch families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.
This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add versions of the phy_page_read and _write functions to
be used in a context where the SMI mutex is held.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_unlink() which notifies NETDEV_CHANGEUPPER, returns
void, as well as del_nbp(). So there's no advantage to catch an eventual
error from the port_bridge_leave routine at the DSA level.
Make this routine void for the DSA layer and its existing drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename DSA port_join_bridge and port_leave_bridge routines to
respectively port_bridge_join and port_bridge_leave in order to respect
an implicit Port::Bridge namespace.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
