- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
Add support to get regulator information of 3.3V and 12V supplies of a PCIe
slot from the respective controller's device-tree node and enable those
supplies. This is required in platforms like p2972-0000 where the supplies
to x16 slot owned by C5 controller need to be enabled before attempting to
enumerate the devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support to configure sideband signal pins when the information is
present in the respective controller device-tree node.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fold in YueHaibing's fix for build error without CONFIG_PINCTRL;
https://lore.kernel.org/r/20190920014807.38288-1-yuehaibing@huawei.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Some PCIe controllers can be set to either Host or EP according to some
early boot FW. To make sure there is no discrepancy (e.g. FW configured
the port to EP mode while the DT specifies it as a host bridge or vice
versa), a check has been added for each mode.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This driver is DT based and utilizes the DesignWare APIs.
It allows using a smaller ECAM range for a larger bus range -
usually an entire bus uses 1MB of address space, but the driver
can use it for a larger number of buses. This is achieved by using a HW
mechanism which allows changing the BUS part of the "final" outgoing
config transaction. There are 2 HW regs, one which is basically a
bitmask determining which bits to take from the AXI transaction itself
and another which holds the complementary part programmed by the
driver.
All link initializations are handled by the boot FW.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
devm_of_phy_get_by_index() can fail for a number of reasons besides
probe deferral. It can for example return -ENOMEM if it runs out of
memory as it tries to allocate devres structures. Propagating only
-EPROBE_DEFER is problematic because it results in these legitimately
fatal errors being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get_by_index() returns -ENODEV in this
case, so that's the special case that we need to handle. So we propagate
all errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: kernel@pengutronix.de
Cc: linux-imx@nxp.com
devm_of_phy_get() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate devres structures. Propagating only -EPROBE_DEFER
is problematic because it results in these legitimately fatal errors
being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get() returns -ENODEV in this case, so
that's the special case that we need to handle. So we propagate all
errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
The num-lanes is optional since it is not needed on some platforms
that bring up the link in firmware.
The link programming is based on the num-lanes properties (which is
optional); if it is not present code must return instead of fiddling
with the lanes value to print an error message.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Static variable kirin_dw_pcie_ops, of type dw_pcie_ops, is used only
once, when it is assigned to the constant field ops of variable pci
(having type dw_pcie) so kirin_dw_pcie_ops is never modified.
Make it constant to protect it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers
beyond that point, avoiding the following abort on a i.MX 6Quad:
# cat /sys/devices/soc0/soc/1ffc000.pcie/pci0000\:00/0000\:00\:00.0/config
[ 100.021433] Unhandled fault: imprecise external abort (0x1406) at 0xb6ea7000
...
[ 100.056423] PC is at dw_pcie_read+0x50/0x84
[ 100.060790] LR is at dw_pcie_rd_own_conf+0x44/0x48
...
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Add CONFIG_PCI_LAYERSCAPE_EP so that endpoint and host controller
drivers can be built separately.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The layerscape PCIe controller have 4 BARs.
BAR0 and BAR1 are 32bit, BAR2 and BAR4 are 64bit and that's a
fixed hardware configuration.
Set the bar_fixed_64bit variable accordingly.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support to enable CDM (Configuration Dependent Module) register
check for any data corruption based on the DT property
'snps,enable-cdm-check'.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Export the dw_pcie_wait_for_link() function to be able to build drivers
using it as loadable modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move PCIe config space capability search API to common DesignWare file
as this can be used by both host and EP mode drivers.
Signed-off-by: Vidya Sagar <vidyaos@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Some of DesignWare core's DBI registers (a.k.a configuration space
registers) are write-protected with a lock without enabling which they
are read-only by default.
These write-protected registers are implementation specific. Tegra194's
BAR-0 register which is at offset 0x10 in the configuration space is an
example. Current implementation in dw_pcie_setup_rc() API attempts to
unlock those write-protected registers whenever they are updated and
lock them back again for writing.
Group all write-protected registers writes so that locking and unlocking
is performed once to avoid bloating the code with multiple unlock/lock
sequences for all those write-protected registers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
- Move qcom driver to bulk clock API (Bjorn Andersson)
- Add Qualcomm QCS404 PCIe controller support (Bjorn Andersson)
- Ensure Qualcomm PERST is asserted for at least 100ms (Niklas Cassel)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
PCI: qcom: Add QCS404 PCIe controller support
dt-bindings: PCI: qcom: Add QCS404 to the binding
PCI: qcom: Use clk bulk API for 2.4.0 controllers
- Add dwc API support to de-initialize host (Vidya Sagar)
- Clean up dwc DBI,ATU read and write APIs (Vidya Sagar)
- Export dwc APIs to support .remove() so drivers can be modular (Vidya
Sagar)
- Simplify imx6 Kconfig dependencies (Leonard Crestez)
- Fix dra7xx build error when !CONFIG_GPIOLIB (YueHaibing)
* remotes/lorenzo/pci/dwc:
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: imx6: Simplify Kconfig depends on
PCI: dwc: Export APIs to support .remove() implementation
PCI: dwc: Cleanup DBI,ATU read and write APIs
PCI: dwc: Add API support to de-initialize host
If CONFIG_GPIOLIB is not selected the compilation results in the
following build errors:
drivers/pci/controller/dwc/pci-dra7xx.c:
In function dra7xx_pcie_probe:
drivers/pci/controller/dwc/pci-dra7xx.c:777:10:
error: implicit declaration of function devm_gpiod_get_optional;
did you mean devm_regulator_get_optional? [-Werror=implicit-function-declaration]
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
drivers/pci/controller/dwc/pci-dra7xx.c:778:45: error: ‘GPIOD_OUT_HIGH’
undeclared (first use in this function); did you mean ‘GPIOF_INIT_HIGH’?
reset = devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~
GPIOF_INIT_HIGH
Fix them by including the appropriate header file.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
The imx6 driver can be used on imx6sx without enabling support for
imx6q or imx7d but the "depends on" condition doesn't allow that.
Instead of making the condition even longer just make it depend on
"ARCH_MXC || COMPILE_TEST" instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Export all configuration space access APIs and also other APIs to
support host controller drivers of dwc core based implementations while
adding support for .remove() hook to build their respective drivers as
modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cleanup DBI read and write APIs by removing leading "__" (underscore)
from their names as there is no reason to have leading underscores
in the first place in the function definition.
Remove dbi/dbi2 base address parameters as the same behaviour can be
obtained through read and write APIs. Since dw_pcie_{readl/writel}_dbi()
APIs can't be used for ATU read/write as ATU base address could be
different from DBI base address, implement ATU read/write APIs using ATU
base address without using dw_pcie_{readl/writel}_dbi() APIs.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Add an API to group all the tasks to be done to de-initialize host which
can then be called by any dwc core based driver implementations
while adding .remove() support in their respective drivers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Bring PHY support for the Armada8k driver.
The Armada8k IP only supports x1, x2 or x4 link widths. Iterate over
the DT 'phys' entries and configure them one by one. Use
phy_set_mode_ext() to make use of the submode parameter (initially
introduced for Ethernet modes). For PCI configuration, let the submode
be the width (1, 2, 4, etc) so that the PHY driver knows how many
lanes are bundled. Do not error out in case of error for compatibility
reasons.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, there is only a 1 ms sleep after asserting PERST.
Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.
Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.
The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:
"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."
Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
The QCS404 platform contains a PCIe version 2.4.0 controller and a
Qualcomm PCIe2 PHY. The driver already supports version 2.4.0, for the
IPQ4019, but this support touches clocks and resets related to the PHY
as well and there's no upstream driver for the PHY.
On QCS404 we must initialize the PHY, so a separate PHY driver is
implemented to take care of this and the controller driver is updated to
not require the PHY related resources. This is done by relying on the
fact that operations in both the clock and reset framework are NOPs when
passed NULL, so we can isolate this change to only the
qcom_pcie_get_resources_2_4_0() function.
For QCS404 we also need to enable the AHB (iface) clock, in order to
access the register space of the controller, but as this is not part of
the IPQ4019 DT binding this is only added for new users of the 2.4.0
controller.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Before introducing the QCS404 platform, which uses the same PCIe
controller as IPQ4019, migrate this to use the bulk clock API, in order
to make the error paths slighly cleaner.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
- Simplify imx7d_pcie_wait_for_phy_pll_lock() by using
regmap_read_poll_timeout() (Andrey Smirnov)
- Drop imx6_pcie_wait_for_link() in favor of the more generic
dw_pcie_wait_for_link() (Andrey Smirnov)
- Return -ETIMEDOUT instead of -EINVAL from
imx6_pcie_wait_for_speed_change() (Andrey Smirnov)
- Remove unused PCIE_PL_PFLR_* constants from imx6 (Andrey Smirnov)
- Use shared PHY debug register definitions in imx6 (Andrey Smirnov)
- Use BIT() in imx6 (Andrey Smirnov)
- Simplify imx6 PHY bit operations (Andrey Smirnov)
- Simplify imx6 pcie_phy_poll_ack() (Andrey Smirnov)
- Use data types that match actual imx6 PHY register width (Andrey
Smirnov)
- Mark imx6 suspend support with drvdata flags instead of checking
variants (Andrey Smirnov)
- Sleep instead of delay in imx6_pcie_enable_ref_clk() (Andrey Smirnov)
* remotes/lorenzo/pci/imx:
PCI: imx6: Use usleep_range() in imx6_pcie_enable_ref_clk()
PCI: imx6: Use flags to indicate support for suspend
PCI: imx6: Restrict PHY register data to 16-bit
PCI: imx6: Simplify pcie_phy_poll_ack()
PCI: imx6: Simplify bit operations in PHY functions
PCI: imx6: Make use of BIT() in constant definitions
PCI: dwc: imx6: Share PHY debug register definitions
PCI: imx6: Remove PCIE_PL_PFLR_* constants
PCI: imx6: Return -ETIMEOUT from imx6_pcie_wait_for_speed_change()
PCI: imx6: Drop imx6_pcie_wait_for_link()
PCI: imx6: Simplify imx7d_pcie_wait_for_phy_pll_lock()
Establishing a PCIe link can take a while; allow asynchronous probing so
that link establishment can happen in the background while other devices
are being probed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently DWC host does not support the remove callback, but nothing
prevents us from supporting it.
Save the root bus for clean up work in driver remove code paths to allow
DWC host drivers to implement their remove hook as, eg:
static int foo_pcie_remove(struct platform_device *pdev)
{
...
pci_stop_root_bus(pp->root_bus);
pci_remove_root_bus(pp->root_bus);
dw_pcie_free_msi(pp);
...
}
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
If we ever did MSI-related initializations, we need to call
dw_pcie_free_msi() in the error code path.
Remove the IS_ENABLED(CONFIG_PCI_MSI) check for MSI init because
pci_msi_enabled() already has a stub for !CONFIG_PCI_MSI.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
To avoid a memory leak, free the page allocated for MSI IRQ in
dw_pcie_free_msi().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Check msi_irq variable before calling irq_set_chained_handler() and
irq_set_handler_data(), lest we call those functions for an invalid MSI
IRQ.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Move the device class fudge to a proper fixup function, and remove
qcom_pcie_rd_own_conf() which has become useless.
dw_pcie_setup_rc() already did the right thing, but it's broken
on older qcom chips, such as 8064.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Configure the Resizable BAR capability to advertise the smallest size
(1MB) for a couple of reasons:
- Host side resource allocation of BAR fails for larger sizes
- Endpoint function driver does not allocate memory for all supported
sizes in the Resizable BAR capability.
If and when there is a usecase required to add more flexibility using
the Resizable BAR capability, this can be revisited.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe EP support for AM654x Platforms in pci-keystone.c
Link: https://lore.kernel.org/linux-pci/20190325093947.32633-15-kishon@ti.com/
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: made dev_vdbg() call a comment]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
imx6_pcie_enable_ref_clk() is never called in atomic context, so
there's no need to use udelay(). Replace it with usleep_range().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Now that driver data has flags variable that can be used to indicate
quirks/features supported we can switch the code to use it instead of
having a special function that does so based on variant alone. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
PHY registers on i.MX6 are 16-bit wide, so we can get rid of explicit
masking if we restrict pcie_phy_read()/pcie_phy_write() to use 'u16'
instead of 'int'. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify pcie_phy_poll_ack() by incorporating shifting into constant
definition and convert the code to use 'bool'. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify the code by incorporating left shifts into constant
definitions as well as using FIELD_PREP/GENMASK. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Avoid using explicit left shifts and convert various definitions to
use BIT() instead. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Both pcie-designware.c and pci-imx6.c contain custom definitions for
PHY debug registers R0/R1 and on top of that there's already a
definition for R0 in pcie-designware.h. Move all of the definitions to
pcie-designware.h. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Change error code from -EINVAL to -ETIMEDOUT in
imx6_pcie_wait_for_speed_change() since that error code seems more
appropriate.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
All calls to imx6_pcie_wait_for_link() share the same error path and
the state of PHY debug registers will already be printed there, so
there's no real reason we can't just use dw_pcie_wait_for_link(). Drop
imx6_pcie_wait_for_link() and replace it with dw_pcie_wait_for_link().
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Make use of regmap_read_poll_timeout() to simplify
imx7d_pcie_wait_for_phy_pll_lock(). No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Add driver for Amazon's Annapurna Labs PCIe host controller. The
controller is based on DesignWare's IP.
The controller doesn't support accessing the Root Port's config space via
ECAM, so we obtain its base address via an AMZN0001 device.
Furthermore, the DesignWare PCIe controller doesn't filter out config
transactions sent to devices 1 and up on its bus, so they are filtered by
the driver.
All subordinate buses do support ECAM access.
Implementing specific PCI config access functions involves:
- Adding an init function to obtain the Root Port's base address from
an AMZN0001 device.
- Adding a new entry in the MCFG quirk array.
[bhelgaas: Note that there is no Kconfig option for this driver because it
is only intended for use with the generic ACPI host bridge driver. This
driver is only needed because the DesignWare IP doesn't completely support
ECAM access to the root bus.]
Link: https://lore.kernel.org/lkml/1553774276-24675-1-git-send-email-jonnyc@amazon.com
Co-developed-by: Vladimir Aerov <vaerov@amazon.com>
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Vladimir Aerov <vaerov@amazon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's AM654 do not have aseparate address space for
dbi2 instead they are accessed using the same address space as dbi
with some configuration bit set. In order to support such platforms,
add callbacks for accessing dbi2 address space.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler") while
adding MSI-X callback handler, introduced dw_pcie_ep_find_capability()
and __dw_pcie_ep_find_next_cap() for finding the MSI and MSIX capability.
However if MSI or MSIX capability is the last capability (i.e there are
no additional items in the capabilities list and the Next Capability
Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0'
even though MSI or MSIX capability may be present because of
incorrect ordering of the "next_cap_ptr" check. Fix it.
Fixes: beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add const qualifier to struct dw_pcie_ep_ops member of
struct dw_pcie_ep.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe in TI's AM654 devices is by default configured to work in GEN3 mode.
However PCIe does not work reliably in GEN3 mode because of SERDES
configuration.
Add support to set the link speed to GEN1, GEN2 or GEN3 based on
"max-link-speed" DT property with GEN2 as the default speed if
"max-link-speed" is absent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
SERDES connected to the PCIe controller in AM654 requires
power on reset enable (POR_EN) to be set in the SERDES. The
SERDES driver sets POR_EN in the reset ops and it has to be
invoked before init or enable ops. In order for SERDES driver
to set POR_EN, invoke the phy_reset() API in pci-keystone driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe RC support for AM654x Platforms in pci-keystone.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Synopsys designware version >= 4.80 uses a separate register space
for programming ATU. The current code identifies if there exists a
separate register space by accessing the register address of ATUs
in designware version < 4.80. Accessing this address results in
abort in the case of K2G.
Fix it here by adding "version" member to struct dw_pcie. This should be
set by platform specific drivers and designware core will use it to
identify if the platform has a separate ATU space. For platforms which
have not populated the version member, the old method of identification
will still be used.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Explicitly set the PCIe mode to BOOTCFG_DEVCFG instead of always
relying on the default values. This is required when EP mode has to
be explicitly written to BOOTCFG_DEVCFG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move platform_get_resource() calls for resources that are applicable to
both host and endpoint mode (ie "dbics" and "app") from
ks_add_pcie_port() to the probe() callback, in preparation for adding
endpoint support to pci-keystone driver.
No functional change intended.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use platform_get_resource_byname() instead of platform_get_resource()
which uses an index to get memory resources. While at that get the memory
resource defined specifically for configuration space instead of
deriving the configuration space address from dbics address space.
Since the pci-keystone driver has never worked in the mainline kernel,
DT backward compatibility is not an issue.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Instead of having two functions
ks_pcie_add_pcie_port() and ks_pcie_dw_host_init() for initializing
host, have a single function to perform all the host initialization.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci-keystone driver uses irq_of_parse_and_map() to get irq number of
error_irq.
Use platform_get_irq() instead and move platform_get_irq() and
request_irq() of error_irq from ks_pcie_add_pcie_port to ks_pcie_probe
since error_irq is common to both RC mode and EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add start_link()/stop_link() dw_pcie_ops and invoke ks_pcie_start_link()
directly from host_init. start_link()/stop_link() ops are required for
adding EP mode support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Platforms which populate msi_host_init() have their own MSI controller
logic. Writing to MSI control registers on platforms which do not use
Designware's MSI controller logic might have side effects.
To be safe, do not write to MSI control registers if the platform uses
its own MSI controller logic instead of Designware's MSI one.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that Keystone started using its own msi_irq_chip, remove
Keystone specific callback functions defined in dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use Keystone specific msi_irq_chip to configure the MSI controller
logic in the PCIe keystone wrapper instead of using the default
Designware msi_irq chip (dw_pci_msi_bottom_irq_chip) with
callback functions for configuring the Keystone MSI controller.
This will help to remove Keystone specific callback functions
added in dw_pcie_host_ops.
Move the default msi_irq_chip assignment to dw_pcie_host_init since
platforms that doesn't use the default msi_irq_chip will assign
msi_irq_chip in the msi_host_init() callback.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Platforms using DesignWare IP use dw_pci_msi_bottom_irq_chip for
configuring the MSI controller logic within the DesignWare IP. However
certain platforms like Keystone (K2G) which uses DesignWare IP have
their own MSI controller logic. For handling such platforms,
the irqchip ops use msi_irq_ack(), msi_set_irq(), msi_clear_irq()
callback functions.
Add support to use different msi_irq_chip with default set to
dw_pci_msi_bottom_irq_chip. This is in preparation to get rid of
msi_irq_ack(), msi_set_irq(), msi_clear_irq() and other Keystone
specific dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ks_pcie_msi_irq_handler() invokes ks_pcie_handle_msi_irq() for handling
the interrupts.
Having two functions for handling the interrupt was used when keystone
PCIe driver was implemented using two files but with commit b492aca35c
("PCI: keystone: Merge pci-keystone-dw.c and pci-keystone.c"), which
merged the keystone PCIe driver to use a single file, two functions for
handling the interrupt handler are not required.
Handle MSI interrupt in a single interrupt handler here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ks_pcie_msi_irq_handler() uses 'virq' to get the IRQ number offset.
This offset is used to get the correct MSI_IRQ_STATUS register
corresponding to the IRQ line that raised the interrupt.
There is no guarantee that 'virq' assigned for consecutive hardware
IRQ will be contiguous and this might get us an incorrect IRQ number
offset.
Fix it here by using 'hwirq' to get the IRQ number offset. Since we
don't store the 'virq' numbers of all the IRQ numbers, stop checking
if irq count is greater than MAX_MSI_HOST_IRQS and remove
MAX_MSI_HOST_IRQS.
Link: https://lkml.kernel.org/r/bb081d21-7c03-0357-4294-7e92d95d838c@arm.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ks_pcie_get_irq_controller_info() is used to configure both MSI and
legacy interrupt. This will prevent MSI or legacy interrupt specific
intializations. Add separate functions to configure MSI and legacy
interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Change both MSI interrupt and legacy interrupt
related macros to take an additional argument in order to return the
correct register offset.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The call to of_parse_phandle() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pci/controller/dwc/pci-layerscape.c:204:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 198, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The call to of_get_child_by_name() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Detected by coccinelle with the following warnings:
./drivers/pci/controller/dwc/pcie-uniphier.c:283:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 274, but without a corresponding object release within this function.
./drivers/pci/controller/dwc/pcie-uniphier.c:290:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 274, but without a corresponding object release within this function.
./drivers/pci/controller/dwc/pcie-uniphier.c:296:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 274, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Detected by coccinelle with the following warnings:
./drivers/pci/controller/dwc/pci-dra7xx.c:252:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 241, but without a corresponding object release within this function.
./drivers/pci/controller/dwc/pci-dra7xx.c:255:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 241, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: Add the layerscape EP device support
PCI: layerscape: Add EP mode support
arm64: dts: Add the PCIE EP node in dts
dt-bindings: add DT binding for the layerscape PCIe controller with EP mode
PCI: endpoint: Remove features member in struct pci_epc
PCI: designware-plat: Remove setting epc->features in Designware plat EP driver
PCI: rockchip: Remove pci_epf_linkup() from Rockchip EP driver
PCI: cadence: Remove pci_epf_linkup() from Cadence EP driver
PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features
PCI: pci-epf-test: Do not allocate next BARs memory if current BAR is 64Bit
PCI: pci-epf-test: Remove setting epf_bar flags in function driver
PCI: endpoint: Fix pci_epf_alloc_space() to set correct MEM TYPE flags
PCI: endpoint: Add helper to get first unreserved BAR
PCI: cadence: Populate ->get_features() cdns_pcie_epc_ops
PCI: rockchip: Populate ->get_features() dw_pcie_ep_ops
PCI: pci-dra7xx: Populate ->get_features() dw_pcie_ep_ops
PCI: designware-plat: Populate ->get_features() dw_pcie_ep_ops
PCI: dwc: Add ->get_features() callback function to dw_pcie_ep_ops
PCI: endpoint: Add new pci_epc_ops to get EPC features
PCI: endpoint: functions: Use memcpy_fromio()/memcpy_toio()
Since 7c5925afbc (PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API) the MSI init claims one of the controller IRQs as a
chained IRQ line for the MSI controller. On some designs, like the i.MX6,
this line is shared with a PCIe legacy IRQ. When the line is claimed for
the MSI domain, any device trying to use this legacy IRQs will fail to
request this IRQ line.
As MSI and legacy IRQs are already mutually exclusive on the DWC core,
as the core won't forward any legacy IRQs once any MSI has been enabled,
users wishing to use legacy IRQs already need to explictly disable MSI
support (usually via the pci=nomsi kernel commandline option). To avoid
any issues with MSI conflicting with legacy IRQs, just skip all of the
DWC MSI initalization, including the IRQ line claim, when MSI is disabled.
Fixes: 7c5925afbc ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: stable@vger.kernel.org
Convert various multi-bit fields to be defined using GENMASK/FIELD_PREP.
This way bit field boundaries are defined in a single place only, as
well as defined in a way that makes it easier to verify them against the
reference manual. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Default implementation of pcie_rd_other_conf() and
dw_pcie_wd_other_conf() share more than 80% of their code. Move shared
code into a dedicated subroutine and convert pcie_rd_other_conf() and
dw_pcie_wd_other_conf() to use it. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Make the intent a bit more clear as well as get rid of explicit
arithmetic by using IS_ALIGNED() to determine if "addr" is aligned to
"size". No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
The PCIe IP block has an additional clock, "pcie_aux", that needs to
be controlled by the driver. Add code to support it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Acquiring the reset GPIO low means that reset is being deasserted, this
is followed almost immediately with qcom_pcie_host_init() asserting it,
initializing it and then finally deasserting it again, for the link to
come up.
Some PCIe devices requires a minimum time between the initial deassert
and subsequent reset cycles. In a platform that boots with the reset
GPIO asserted this requirement is being violated by this deassert/assert
pulse.
Acquire the reset GPIO high to prevent this situation by matching the
state to the subsequent asserted state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org
Add the PCIe EP mode support to the layerscape platform controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <minghuan.lian@nxp.com>
Reviewed-by: Zhiqiang Hou <zhiqiang.hou@nxp.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that pci-epf-test uses get_features callback and
dw_plat_pcie_epc_features in Designware plat EP driver already indicates
it doesn't support linkup notification and is MSIX capable, remove setting
epc->features which is not used anymore by the endpoint function driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by DRA7xx PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by Designware PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
