RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac9 ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.
Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")
Fixes: 7699353da8 ("netdevsim: add ipsec offload testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.
Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.
While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability. This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.
If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output. This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats. Always expose counters from all
the rings. Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.
The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __alx_open function can be called from ndo_open, which is called
under RTNL, or from alx_resume, which isn't. Since commit d768319cd4,
we're calling the netif_set_real_num_{tx,rx}_queues functions, which
need to be called under RTNL.
This is similar to commit 0c2cc02e57 ("igb: Move the calls to set the
Tx and Rx queues into igb_open").
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc7a6c287f ("sfc: use a semaphore to lock farch filters too")
Suggested-by: Joseph Korty <joe.korty@concurrent-rt.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sNaA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The very first version of RTL8169 from 2002 (and only this one) has
support for a TBI 1000BaseX fiber interface. The TBI support in the
driver makes switching to phylib tricky, so best would be to get
rid of it. I found no report from anybody using a device with RTL8169
and fiber interface, also the vendor driver doesn't support this mode
(any longer).
So remove TBI support and bail out with a message if a card with
activated TBI is detected. If there really should be any user of it
out there, we could add a stripped-down version of the driver
supporting chip version 01 and TBI only (and maybe move it to
staging).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see no need to define a private debug output symbol, let's use the
standard debug output functions instead. In this context also remove
the deprecated PFX define.
The one assertion is wrong IMO anyway, this code path is used also
by chip version 01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch checks-
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: No space is necessary after a cast
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch warnings-
WARNING: Block comments use a trailing */ on a separate line
WARNING: Block comments use * on subsequent lines
WARNING: networking block comments don't use an empty /* line,
use /* Comment
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below kernel-doc warnings:
Function parameter or member 'maxlen' not described in 'xemaclite_recv_data'
Function parameter or member 'address'not described in 'xemaclite_set_mac_address'
Excess function parameter 'addr' description in 'xemaclite_set_mac_address'
No description found for return value of 'xemaclite_interrupt'
No description found for return value of 'xemaclite_mdio_write'
Function parameter or member 'dev' not described in 'xemaclite_mdio_setup'
Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup'
No description found for return value of 'xemaclite_open'
No description found for return value of 'xemaclite_close'
Excess function parameter 'match' description in 'xemaclite_of_probe'
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove else as it is not required with if doing a return.
It also coalesce the format onto a single line and add the
missing space after the comma. Fixes below checkpatch warning-
WARNING: else is not generally useful after a break or return
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch hardcoded function name with a reference to __func__ making
the code more maintainable. Address below checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_read',
this function's name, in a string
+ "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_write',
this function's name, in a string
+ "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the skb->protocol field, we have to make sure we use the
proper endianness using htons, and not swab16.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan IDs must not be swapped when creating Header Parser entries. This
has no effect on little-endian systems, but is wrong for big-endian.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2's Header Parser use some large TCAM and SRAM entries, that are
duplicated in software so that we can write them to hardware only when
we are done modifying them.
Currently, PPv2 uses a union containing arrays of u32 and u8 to represent
these entries, to facilitate byte per byte access. This representation is
broken when we want to support big endian, and this makes the code
confusing to read.
This patch drops the union, and simply stores the TCAM and SRAM entries
as u32 arrays, each entry corresponding to a 32-bit register.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller always expect descriptors to be in little endian. We
must therefore force descriptors to use that format, and convert to the
host endianness when necessary.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checkers complain that id_tbl->table points to longs and 4 bytes
is smaller than sizeof(long). But the since other side is dividing by
32 instead of sizeof(long), that means the current code works fine.
Anyway, it's more conventional to use the BITS_TO_LONGS() macro when
we're allocating a bitmap.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for CBS reconfiguration using the TC application.
A new callback was added to TC ops struct and another one to DMA ops to
reconfigure the channel mode.
Tested in GMAC5.10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e netdevice driver updates:
- Boris Pismenny added the support for UDP GSO in the first two patches.
Impressive performance numbers are included in the commit message,
@Line rate with ~half of the cpu utilization compared to non offload
or no GSO at all.
- From Tariq Toukan:
- Convert large order kzalloc allocations to kvzalloc.
- Added performance diagnostic statistics to several places in data path.
From Saeed and Eran,
- Update NIC HW stats on demand only, this is to eliminate the background
thread needed to update some HW statistics in the driver cache in
order to report error and drop counters from HW in ndo_get_stats.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbNVbbAAoJEEg/ir3gV/o+1SMH/R/jBMgqWKzuDL+QUTCm6BNH
Gcu7OPd3CUGT3wUujJ4sgVmYzyp70GZx0f843ct3Bmwcfwh8Yu/eOju7ldoQq2ns
6oz8sL6yvg/zmMfkc7DYFHrJSGu3Qh7fje+8zKVdoGlHkIFwR07bRkQolTKL6hem
qZHbn5o2RhFYLxjlGa7E7w41hXMx27gmHk4V/YdUGzHrExGB0fGbUXkkveCYiGYk
sB/JDSi02xjmEV2Nw8dX5jdZoBivaG2kPcBRD6Gpgmb+hntjIyTqwGdoJ7jDy1vj
A5wWHboj+Q/LtUNvpbb48fc/hhciddSxeB+c/1DMHjd4TchnBmPXyXwz5/7eTj8=
=xft1
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-06-28
mlx5e netdevice driver updates:
- Boris Pismenny added the support for UDP GSO in the first two patches.
Impressive performance numbers are included in the commit message,
@Line rate with ~half of the cpu utilization compared to non offload
or no GSO at all.
- From Tariq Toukan:
- Convert large order kzalloc allocations to kvzalloc.
- Added performance diagnostic statistics to several places in data path.
From Saeed and Eran,
- Update NIC HW stats on demand only, this is to eliminate the background
thread needed to update some HW statistics in the driver cache in
order to report error and drop counters from HW in ndo_get_stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used to change TX workrequests, which helps in
host->vf communication.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The present TX workrequest(FW_ETH_TX_PKT_WR) cant be used for
host->vf communication, since it doesn't loopback the outgoing
packets to virtual interfaces on the same port. This can be done
using FW_ETH_TX_PKT_VM_WR.
This fix depends on ethtool_flags to determine what WR to use for
TX path. Support for setting this flags by user is added in next
commit.
Based on the original work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on px30 Soc.
The base structure is the same, but registers and the bits in
them are moved slightly, and add the clk_mac_speed for selecting
mac speed.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MACRO lower_32_bits and upper_32_bits can help to get bits 0-31
and bits 32-63 of a number, so just use it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_hw is embedded in hclge_dev, so use container_of instead of
back to get hclge_dev.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface h->ae_algo->ops->put_vector is called in both
hns3_nic_dealloc_vector_data and hns3_nic_uninit_vector_data in
hns3_client_uninit, this will cause vector freed twice.
This patch remove the Redundant put_vector to make vector freed
only once.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the ret value in error information can help find the reason.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extraction an interface for state init|uninit to make the code
easier to read.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux/slab.h is not used in hnae3.h, this patch removes it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first bd of a packet is invalid and invalid ring head for tx
IRQ is not offen, they may occur when there is error,
Add unlikely for error check branch is better for performance.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW supports UDP, TCP and SCTP packets checksum for both ipv4 and
ipv6, but do not support other type packets checksum for ipv4 or
ipv6.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hdev->vector_status[vector_id] is already HCLGE_INVALID_VPORT,
should log the error and return.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface init_client_instance and uninit_client_instance
do not register anything, only initialize the client instance.
This patch rename the related interface to make the function
name to indicate the purpose.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hclge_unmap_ring_frm_vector, there are 2 steps:
step 1: get vector index.
step 2 unbind ring with vector.
But it gets vector id again in step 2 interface. This patch
removes hclge_get_vector_index from hclge_bind_ring_with_vector,
and make the step the same with hns3 PF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable periodic stats update background thread and update stats in
background on demand when ndo_get_stats is called.
Having a background thread running in the driver all the time is bad for
power consumption and normally a user space daemon will query the stats
once every specific interval, so ideally the background thread and its
interval can be done in user space..
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
A per-ring counter for NOP operations already exists.
Here I add a counter that sums them up.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add ethtool counter to indicate the number of strides consumed
by filler CQEs.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-channel and global ethtool counters for channel events.
Each event indicates an interrupt on one of the channel's
completion queues.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-ring and global ethtool counters for congested UMR requests.
These events indicate congestion in UMR handlers in HW.
Such event is concluded when there's an outstanding UMR post,
yet the SW consumed at least two additional MPWQEs in the meanwhile.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-channel and global ethtool counters for NAPI.
This helps us monitor and analyze performance in general.
- ch[i]_poll:
the number of times the channel's NAPI poll was invoked.
- ch[i]_arm:
the number of times the channel's NAPI poll completed
and armed the completion queues.
- ch[i]_aff_change:
the number of times the channel's NAPI poll explicitly
stopped execution on a cpu due to a change in affinity.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-ring and global ethtool counters for XDP_TX completions.
This helps us monitor and analyze XDP_TX flow performance.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-ring and global ethtool counters for TX completions.
This helps us monitor and analyze TX flow performance.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Local variable 'wq' already points to &sq->wq, use it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Replace calls to kzalloc_node with kvzalloc_node, as it fallsback
to lower-order pages if the higher-order trials fail.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds a counter for tx UDP GSO packets that contain a segment
that is not aligned to MSS - remaining segment.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch enables UDP GSO support. We enable this by using two WQEs
the first is a UDP LSO WQE for all segments with equal length, and the
second is for the last segment in case it has different length.
Due to HW limitation, before sending, we must adjust the packet length fields.
We measure performance between two Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
machines connected back-to-back with Connectx4-Lx (40Gbps) NICs.
We compare single stream UDP, UDP GSO and UDP GSO with offload.
Performance:
| MSS (bytes) | Throughput (Gbps) | CPU utilization (%)
UDP GSO offload | 1472 | 35.6 | 8%
UDP GSO | 1472 | 25.5 | 17%
UDP | 1472 | 10.2 | 17%
UDP GSO offload | 1024 | 35.6 | 8%
UDP GSO | 1024 | 19.2 | 17%
UDP | 1024 | 5.7 | 17%
UDP GSO offload | 512 | 33.8 | 16%
UDP GSO | 512 | 10.4 | 17%
UDP | 512 | 3.5 | 17%
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is clearly a bug.
We need to set the DMA buffer size in the HW otherwise corruption can
occur when receiving packets.
This is probably not occuring because of small MTU values and because HW
has a default value internally (which currently is bigger than default
buffer size).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes for mlx5 core and netdev driver:
Two fixes from Alex Vesker to address command interface issues
- Race in command interface polling mode
- Incorrect raw command length parsing
From Shay Agroskin, Fix wrong size allocation for QoS ETC TC regitster.
From Or Gerlitz and Eli Cohin, Address backward compatability issues for when
Eswitch capability is not advertised for the PF host driver
- Fix required capability for manipulating MPFS
- E-Switch, Disallow vlan/spoofcheck setup if not being esw manager
- Avoid dealing with vport IB/eth representors if not being e-switch manager
- E-Switch, Avoid setup attempt if not being e-switch manager
- Don't attempt to dereference the ppriv struct if not being eswitch manager
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbMtMEAAoJEEg/ir3gV/o+NjAIAMGrerpwg8ADBj+b9tSWm4WV
2yAJ561kBObwhA+uDJtH7mGUO3+AnkcWz9vynGqFdmkOikUcbpPkBb9D+rmFbkX2
E585pwR3pH7lEzYEG4xO6SwuQcQ4OytFNxz94AT6CgNEXqrmbrD7A5Vsgk265yZq
pJzL1OVfkXKOtb2x5PpCOh19/28OxAzyMQfoklsE2Wn7j8/2RWX0UUDxuF8jS+He
9loaurT4Fsfo5JYE+o+k38knHFBkdTUZBD9/bZrtaMcrD68bZdJTpZm6eYwRXW3S
7J88SmH/xTy74f1KY4qf0JOTxnaWtm/r4YaCXf1QD05W2/U9FQpIW1ipMKH51vk=
=te2H
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2018-06-26
Fixes for mlx5 core and netdev driver:
Two fixes from Alex Vesker to address command interface issues
- Race in command interface polling mode
- Incorrect raw command length parsing
From Shay Agroskin, Fix wrong size allocation for QoS ETC TC regitster.
From Or Gerlitz and Eli Cohin, Address backward compatability issues for when
Eswitch capability is not advertised for the PF host driver
- Fix required capability for manipulating MPFS
- E-Switch, Disallow vlan/spoofcheck setup if not being esw manager
- Avoid dealing with vport IB/eth representors if not being e-switch manager
- E-Switch, Avoid setup attempt if not being e-switch manager
- Don't attempt to dereference the ppriv struct if not being eswitch manager
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmiitorgmii is using the mii_bus of the device it's attached to,
instead of the bus it was given during probe.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the IPsec/XFRM offload API for testing.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *enum* {A|M}PR_BIT were declared in the commit 86a74ff21a ("net:
sh_eth: add support for Renesas SuperH Ethernet") adding SH771x support,
however the SH771x manual doesn't have the APR/MPR registers described
and the code writing to them for SH7710 was later removed by the commit
380af9e390 ("net: sh_eth: CPU dependency code collect to "struct
sh_eth_cpu_data""). All the newer SoC manuals have these registers
documented as having a 16-bit TIME parameter of the PAUSE frame, not
1-bit -- update the *enum* accordingly, fixing up the APR/MPR writes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was combining XDP_TX virtqueue_kick and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
The suboptimal behavior was introduced in commit 9267c430c6
("virtio-net: add missing virtqueue kick when flushing packets").
Fixes: 9267c430c6 ("virtio-net: add missing virtqueue kick when flushing packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
It looks like the mistake was copy-pasted from ixgbe.
Fixes: d9314c474d ("i40e: add support for XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
Fixes: 11393cc9b9 ("xdp: Add batching support to redirect map")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware VLAN filtering offloading on ocelot.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link aggregation hardware offload support for Ocelot.
ocelot_get_link_ksettings() is not great but it does work until the driver
is reworked to switch to phylink.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag tc_flower_initialized to indicate the
completion if tc flower initialization.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.
[ 55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0
Fixes: 352f58b0d9 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map read has been supported on NFP, this patch enables optimization
for memcpy from map to packet.
This patch also fixed one latent bug which will cause copying from
unexpected address once memcpy for map pointer enabled. The fixed
code path was not exercised before.
Reported-by: Mary Pham <mary.pham@netronome.com>
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
sizeof() will return unsigned value so in the error check
negative error code will be always larger than sizeof().
Fixes: a0d8e02c35 ("nfp: add support for reading nffw info")
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC shared blocks allow multiple qdiscs to be grouped together and filters
shared between them. Currently the chains of filters attached to a block
are only flushed when the block is removed. If a qdisc is removed from a
block but the block still exists, flow del messages are not passed to the
callback registered for that qdisc. For the NFP, this presents the
possibility of rules still existing in hw when they should be removed.
Prevent binding to shared blocks until the kernel can send per qdisc del
messages when block unbinds occur.
tcf_block_shared() was not used outside of the core until now, so also
add an empty implementation for builds with CONFIG_NET_CLS=n.
Fixes: 4861738775 ("net: sched: introduce shared filter blocks infrastructure")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was not possible to distinguish between mpls ether types and
other ether types. This leads to incorrect classification of offloaded
filters that match on mpls ether type. For example the following two
filters overlap:
# tc filter add dev eth0 parent ffff: \
protocol 0x8847 flower \
action mirred egress redirect dev eth1
# tc filter add dev eth0 parent ffff: \
protocol 0x0800 flower \
action mirred egress redirect dev eth2
The driver now correctly includes the mac_mpls layer where HW stores mpls
fields, when it detects an mpls ether type. It also sets the MPLS_Q bit to
indicate that the filter should match mpls packets.
Fixes: bb055c198d ("nfp: add mpls match offloading support")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Manipulating of the MPFS requires eswitch manager capabilities.
Fixes: eeb66cdb68 ('net/mlx5: Separate between E-Switch and MPFS')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.
Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.
Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.
Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.
The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.
1. set_vf_vlan - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac - allowed
4. get_vf_config - allowed
5. set_vf_trust - disallowed
6. set_vf_rate - disallowed
7. get_vf_stat - allowed
8. set_vf_link_state - disallowed
Fixes: f942380c12 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
While here, make sure to disallow eswitch switchdev related
setups through devlink if we are not esw managers.
Fixes: cb67b83292 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
