Continuing the effort to commonize the similar suspend/resume flows,
finish up by using the new fm10k_handle_suspand and fm10k_handle_resume
functions for the standard suspend/resume flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a function level PCI reset is triggered using sysfs, it calls the
driver's .reset_notify error handler. Implement a handler based on the
now split fm10k_prepare_for_reset and fm10k_handle_reset functions, so
that we fully reset the driver when the PCI function level reset occurs.
This also ensures the reset is handled in a clean way by first disabling
all the driver bits first and then restoring them after the function
reset. Previously the stack simply performed a blind function reset and
our driver didn't take any part in the process.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have extracted the necessary steps for a split
suspend/resume flow, re-use these functions instead of using the current
open coded flow. This ensures that we don't miss any steps. It also
ensures that we have the correct driver states set.
Since we'll be handling all of the reset flow ourselves, we no longer
need to request a reset in the io_slot_reset() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement fm10k_prepare_suspend and fm10k_handle_resume functions which
abstract around the now existing fm10k_prepare_for_reset and
fm10k_handle_reset. The new functions also handle stopping the service
task, which is something that the original re-init flow does not need.
Every other location that does a suspend/resume type flow is expected to
use these functions, because otherwise they may have conflicts with the
running watchdog routines. This also has the effect of preventing
possible surprise remove events during handling of FLR events and PCIe
errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several flows in the driver which perform the similar function
of tearing down software and restoring software to recover from certain
errors or PCIe events, including:
* fm10k_reinit
* fm10k_suspend/resume
* fm10k_io_error_detected/fm10k_io_resume
In addition, we want to implement a .reset_notify() handler as well
which will also perform similar function.
Rework how the driver codes reset and resume flows by separating out the
reinit logic into two functions "fm10k_prepare_for_reset" and
"fm10k_handle_reset". This first step will allow us to re-use this
functionality in the similar blocks of code instead of re-coding the
same sequence of events slightly different.
The end result should be more maintainable and correct, fixing several
inconsistencies with the work flow.
The new functions expect to take the rtnl_lock() themselves, and it does
have the unfortunate side effect of having the reinit flow take then
release then take the rtnl_lock. However, this minor downside is
out weighted by the benefits of code reduction and reducing needless
difference between these flows.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It turns out that sometimes during a reset the Tx queues will be
temporarily stuck longer than .stop_hw() expects. Work around this issue
by attempting to .stop_hw() first. If it tails, wait a number of
attempts until the Tx queues appear to be drained. After this, attempt
stop_hw() again. This ensures that we avoid waiting if we don't need to,
such as during the first initialization of a VF, and give the proper
amount of time necessary to recover from most situations. It is possible
that the hardware is actually stuck. For PFs, this is usually fixed by
a datapath reset. Unfortunately the VF cannot request a similar reset
for itself.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stop_hw() routine fails with FM10K_ERR_REQUESTS_PENDING, this
indicates that the Tx or Rx queues did not shutdown within the time
limit. Print a more suitable message at the dev_info level instead of
dev_err.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A while ago, an additional check for the switch being ready was added to
reset_hw. A recent refactor accidentally made this check return an error
code on failure which caused fm10k_probe to fail when the switch wasn't
brought up first. The original reasoning for the check was to prevent
additional data path reset when the fabric wasn't ready yet. However,
there isn't a compelling reason to keep the check, as the data path
reset will restore hardware to a known good state. Remove the check and
perform the data path reset regardless of the switch manager state.
An alternative fix is to return FM10K_SUCCESS instead, and bypass the
actual data path reset. This should be fine as we will perform
a reset_hw once the switch is active. However, since data path reset
will reset many parts of the hardware it seems better to just perform
the reset regardless of switch state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.
In order to prevent having to re-assign err to 0, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a data path reset is initiated, write control to the PCIE_GMBX is
yanked from the switch manager. The switch manager writes to this
register to clear mailbox global interrupt bits as part of its mailbox
interrupt handling routine. When the device recovers from the data path
reset and these bits are not cleared, it will prevent future mailbox
global interrupts from being triggered. Upon confirming that the device
has exited from a data path reset, clear these bits to ensure the proper
functioning of the mailbox global interrupt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also prevent updating stats while the interface is down. If we're
already updating stats, just return doing nothing. When we take the
device down, block stat updates until we come back up. This ensures that
we avoid tearing down rings when we're updating statistics, and prevents
updating statistics until we're up.
We can't re-use the __FM10K_DOWN for this because it wouldn't prevent
multiple threads from accessing statistics. Neither does it prevent the
case where we start updating stats and then start going down in another
thread.
The fm10k_get_stats64 is except from this, because it has a completely
different flow which does not suffer from the same issues as
fm10k_update_stats might.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's currently possible for fm10k_update_stats to be called during the
window when we go down and the rings are removed. This can result in
a null pointer dereference. In fm10k_get_stats64 we work around this by
using ACCESS_ONCE and a null pointer check inside the loop. Use this
same flow in the fm10k_update_stats to avoid the potential null pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return early from fm10k_down() when we are already down, since that
means another thread is either already finished or has started going
down, so shouldn't conflict with them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Expose the transmit queue length of each traffic class and the amount of
unicast packets discarded due to insufficient room in the shared buffer.
The first counter allows us to debug user priority to traffic class
mapping, whereas the drop counter is useful when determining shared buffer
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose per-priority bytes / packets / PFC packets counters via ethtool.
These counters are very useful when debugging QoS functionality and
provide a better insight into the device's forwarding plane.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function
cpmac_probe() in the error handling case.
This patch revert commit 0465be8f4f ("net: cpmac: fix in
releasing resources"), which changed to only free_netdev
while register_netdev failed.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ops->reset() error handling case, clk_disable_unprepare() is missed
before return from this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 46aa27df88 ('net: axienet: Use devm_* calls')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ret variable is unused in wlcore_probe_of()
Remove it for fixing build warning.
Fixes: 01efe65aba ("wlcore: spi: add wl18xx support")
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A user will now be able to loop packets back out of the same port using
a bpf program attached to xdp hook. Updates to the packet contents from
the bpf program is also supported.
For the packet write feature to work, the rx buffers are now mapped as
bidirectional when the page is allocated. This occurs only when the xdp
hook is active.
When the program returns a TX action, enqueue the packet directly to a
dedicated tx ring, so as to avoid completely any locking. This requires
the tx ring to be allocated 1:1 for each rx ring, as well as the tx
completion running in the same softirq.
Upon tx completion, this dedicated tx ring recycles pages without
unmapping directly back to the original rx ring. In steady state tx/drop
workload, effectively 0 page allocs/frees will occur.
In order to separate out the paths between free and recycle, a
free_tx_desc func pointer is introduced that is optionally updated
whenever recycle_ring is activated. By default the original free
function is always initialized.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for writing the tx descriptor from multiple functions,
create a helper for both normal and blueflame access.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver by default allocates order-3 pages for the ring to
consume in multiple fragments. When the device has an xdp program, this
behavior will prevent tx actions since the page must be re-mapped in
TODEVICE mode, which cannot be done if the page is still shared.
Start by making the allocator configurable based on whether xdp is
running, such that order-0 pages are always used and never shared.
Since this will stress the page allocator, add a simple page cache to
each rx ring. Pages in the cache are left dma-mapped, and in drop-only
stress tests the page allocator is eliminated from the perf report.
Note that setting an xdp program will now require the rings to be
reconfigured.
Before:
26.91% ksoftirqd/0 [mlx4_en] [k] mlx4_en_process_rx_cq
17.88% ksoftirqd/0 [mlx4_en] [k] mlx4_en_alloc_frags
6.00% ksoftirqd/0 [mlx4_en] [k] mlx4_en_free_frag
4.49% ksoftirqd/0 [kernel.vmlinux] [k] get_page_from_freelist
3.21% swapper [kernel.vmlinux] [k] intel_idle
2.73% ksoftirqd/0 [kernel.vmlinux] [k] bpf_map_lookup_elem
2.57% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
After:
31.72% swapper [kernel.vmlinux] [k] intel_idle
8.79% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
7.54% swapper [kernel.vmlinux] [k] poll_idle
6.36% swapper [mlx4_core] [k] mlx4_eq_int
4.21% swapper [kernel.vmlinux] [k] tasklet_action
4.03% swapper [kernel.vmlinux] [k] cpuidle_enter_state
3.43% swapper [mlx4_en] [k] mlx4_en_prepare_rx_desc
2.18% swapper [kernel.vmlinux] [k] native_irq_return_iret
1.37% swapper [kernel.vmlinux] [k] menu_select
1.09% swapper [kernel.vmlinux] [k] bpf_map_lookup_elem
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BPF_PROG_TYPE_XDP hook in mlx4 driver.
In tc/socket bpf programs, helpers linearize skb fragments as needed
when the program touches the packet data. However, in the pursuit of
speed, XDP programs will not be allowed to use these slower functions,
especially if it involves allocating an skb.
Therefore, disallow MTU settings that would produce a multi-fragment
packet that XDP programs would fail to access. Future enhancements could
be done to increase the allowable MTU.
The xdp program is present as a per-ring data structure, but as of yet
it is not possible to set at that granularity through any ndo.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bogus PHY interrupts are observed. This masks the PHY interrupt
when the interface works in NCSI mode as there is no attached
PHY under the circumstance.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches the driver with devices compatible with "faraday,ftgmac100"
declared in the device tree. Originally, device's name from device
tree for it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes ftgmac100 driver support NCSI mode. The NCSI is enabled
on the interface if property "use-nc-si" or "use-ncsi" is found from
the device node in device tree.
* No PHY device is used when NCSI mode is enabled.
* The NCSI device (struct ncsi_dev) is created when probing the
device while it's enabled/started when the interface is brought
up.
* Hardware IP checksum dosn't work when NCSI mode is enabled. It
is disabled on enabled NCSI.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is assigned with random MAC address. It isn't reasonable.
An valid MAC address might have been provided by (uboot) firmware by
device-tree or in chip. It's reasonable to use it to maintain consistency.
This uses the MAC address from device-tree or that in the chip if it's
valid. Otherwise, a random MAC address is given as before.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces two helper functions to create or destroy MDIO
interface. No logical changes introduced except the proper MDIO
names are given when having more than one MDIO bus.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA driver function to configure the bridge ageing time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips from (88E6060 to 88E6390) have a ATU Control
register containing bits 11:4 to configure an ATU Age Time quotient.
However the coefficient used to calculate the ATU Age Time vary with the
models. E.g. 88E6060, 88E6352 and 88E6390 use respectively 16, 15 and
3.75 seconds.
Add a age_time_coeff to the info structure to handle this and a Global 1
helper to set the default age time of 5 minutes in the setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability flags to describe the presence of Ingress Rate Limit unit
registers and an helper function to clear it.
In the meantime, fix a few harmless issues:
- 6185 and 6095 don't have such registers (reserved)
- the previous code didn't wait for the IRL operation to complete
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags and helpers to describe the presence of Priority Override
Table (POT) related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Cross-chip Port VLAN Table (PVT)
related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches such as 88E6185 as 3 Switch MAC registers in Global 1. Newer
chips such as 88E6352 have freed these registers in favor of an indirect
access in a Switch MAC/WoL/WoF register in Global 2.
Explicit this difference with G1 and G2 helpers and flags.
Also, note that this indirect access is a single-register which doesn't
require to wait for the operation to complete (like Switch MAC, Trunk
Mapping, etc.), in contrary to multi-registers indirect accesses with
several operations and a busy bit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches provide a Rsvd2CPU mechanism used to choose which of the
16 reserved multicast destination addresses matching 01:80:c2:00:00:0x
should be considered as MGMT and thus forwarded to the CPU port.
Other switches extend this mechanism to also configure as MGMT the
additional 16 reserved multicast addresses matching 01:80:c2:00:00:2x.
This mechanism is exposed via two registers in Global 2, and an Rsvd2CPU
enable bit in the management register.
Newer chip (such as 88E6390) has replaced these registers with a new
indirect MGMT mechanism in Global 1.
The patch adds two MV88E6XXX_FLAG_G2_MGMT_EN_{0,2}X flags to describe
the presence of these Global 2 registers. If 88E6390 support is added, a
MV88E6XXX_FLAG_G1_MGMT_CTRL flag will be needed to setup Rsvd2CPU.
Note: all switches still support in parallel the ATU Load operation with
an MGMT Entry State to forward such frames in a less convenient way.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Trunk Mask and Trunk Mapping registers are two Global 2 indirect
accesses to trunking configuration.
Add helpers for these tables and simplify the Global 2 setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Device Mapping register is an indirect table access.
Provide helpers to access this table and explicit the checking of the
new DSA_RTABLE_NONE routing table value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the setup of Global 1 and Global 2 internal SMI devices and add
a flag to describe the presence of this second registers set.
Also rearrange the G1 setup in the registers order.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 88E6xxx Marvell switches (even the old not supported yet 88E6060)
have at least an ATU, per-port STP states and VLAN map, to run basic
switch functions such as Spanning Tree and port based VLANs.
Get rid of the related MV88E6XXX_FLAG_{ATU,PORTSTATE,VLANTABLE} flags,
as they are defaults to every chip.
This enables STP on 6185 and removes many inconsistencies on others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and MQ control was doing DMA from the stack. Fix it.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: "netdev@vger.kernel.org" <netdev@vger.kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txr->dev_state was not consistently manipulated with the acquisition of
the per-queue lock, after further inspection the lock does not seem
necessary, either the value is read as BNXT_DEV_STATE_CLOSING or 0.
Reported-by: coverity (CID 1339583)
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the lost of Ethernet port on low memory system,
when driver frees its resources and fails to allocate new resources.
Issue could happen while changing number of channels, rings size or
changing the timestamp configuration.
This fix is necessary because of removing vmap use in the code.
When vmap was in use driver could allocate non-contiguous memory
and make it contiguous with vmap. Now it could fail to allocate
a large chunk of contiguous memory and lose the port.
Current code tries to allocate new resources and then upon success
frees the old resources.
Fixes: 73898db043 ('net/mlx4: Avoid wrong virtual mappings')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filters cleanup should be done once before destroying net device,
since filters list is contained in the private data.
Fixes: 1eb8c695bd ('net/mlx4_en: Add accelerated RFS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge device in NS2 has the same device ID as the ethernet controller.
Add check to avoid probing the bridge device.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate special vnic for dropping packets not matching the RX filters.
First vnic is for normal RX packets and the driver will drop all
packets on the 2nd vnic.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate napi for special vnic, packets arriving on this
napi will simply be dropped and the buffers will be replenished back
to the HW.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware is unable to drop rx packets not matching the RX filters. To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it. We then setup the
driver to drop packets received on this VNIC.
This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings. Only shared completion ring mode is
supported. The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro A0 has a hardware bug in the rx path. The workaround is to create
a special COS context as a path for non-RSS (non-IP) packets. Without this
workaround, the chip may stall when receiving RSS and non-RSS packets.
Add infrastructure to allow 2 contexts (RSS and CoS) per VNIC. Allocate
and configure the CoS context for Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro is the embedded version of the ethernet controller in the North
Star 2 SoC. Add basic code to recognize the chip ID and disable
the features (ntuple, TPA, ring and port statistics) not supported on
Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions used standards registers in a different page
for both interfaces: copper and fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be correctly initilized, the fiber interface needs
to be configured via autonegociation registers which use
some customs options or registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the fiber receiver error counter in the
statistics. Rename the current counter which is for copper errors to
phy_receive_errors_copper, so it is easy to distinguish copper from
fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
For concerned phy, the fiber link is checked before the copper link.
According to datasheet, the link which is up is enabled.
If both links are down, copper link would be used.
To detect fiber link status, we used the real time status
because of troubles with the copper method.
Tested with Marvell 88E1512.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently 'ifconfig' for the Ethernet devices handled by this driver shows
"DMA chan: ff" while the driver doesn't use any DMA channels. Not assigning
a value to 'net_device::dma' causes 'ifconfig' to correctly not report a
DMA channel.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently 'ifconfig' for the Ethernet devices handled by this driver shows
"DMA chan: ff" while the driver doesn't use any DMA channels. Not assigning
a value to 'net_device::dma' causes 'ifconfig' to correctly not report a
DMA channel.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'cpmac_open', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Also, we don't need to free these resources if the allocation has failed.
So I have slighly modified the goto label in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath9k
* implement temperature compensation support for AR9003+
ath10k
* disable wake_tx_queue() mac80211 op for older devices to workaround
throughput regression
For rtl8188ee, we pass -Idrivers/net/wireless/rtlwifi/ to gcc,
however that directy no longer exists, so evidently this option
is no longer required here and can be removed to avoid a warning
when building with 'make W=1' or 'gcc -Wmissing-include-dirs'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for using with both wl12xx and wl18xx.
- all wilink family needs special init command for entering wspi mode.
extra clock cycles should be sent after the spi init command while the
cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
completes the init stage.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011)
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dma_mapping_error() returns an error in dma_rxfill, we would be
leaking a packet that we allocated with brcmu_pkt_buf_get_skb().
Reported-by: coverity (CID 1081819)
Fixes: 67d0cf50bd ("brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case brcmf_sdiod_recv_chain() cannot complete a succeful call to
brcmf_sdiod_buffrw, we would be leaking glom_skb and not free it as we
should, fix this.
Reported-by: coverity (CID 1164856)
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We should use kfree_skb() instead of kfree() to free an skb.
Fixes: 362899b872 ("macvtap: switch to use skb array")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same skb is being reused for storing command response from firmware
in PCIe chipsets. There was a bug while updating the skb length.
This patch ensures skb length correctly gets updated based on rx_len.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In corner case, we may end up processing same interrupt twice.
We have a logic to read pending interrupts at the end of interrupt
processing routine. It has a race with interrupts read in interrupt
handler. This patch solves the problem by ORing the interrupt bitmap
in this case.
The symptom for this bug is below messages in dmesg log.
[ 11.522123] mwifiex_pcie 0000:01:00.0: CMD_RESP: invalid cmd resp
[ 11.680412] mwifiex_pcie 0000:01:00.0: There is no command but got cmdrsp
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that request_irq() failure leads to a system crash
due to a bug in mwifiex driver.
When this failure happens, mwifiex_add_card() already takes care of
clearing and freeing adapter->card pointer. This patch removes the
redundant cleanup code causing crash.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sdio dpc starts processing when in SDIOD_STATE_DATA. This state was
entered right after firmware download. This patch moves that transition
just before enabling sdio interrupt handling thus avoiding watchdog
expiry which would put the bus to sleep while probing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the host-interface bus has hard time handling transmit packets
it informs higher layer about this and it would stop the netdev
queue when needed. However, since commit 9cd18359d3 ("brcmfmac:
Make FWS queueing configurable.") this was broken. With this patch
the behaviour is restored.
Cc: stable@vger.kernel.org # v4.5, v4.6, v4.7
Fixes: 9cd18359d3 ("brcmfmac: Make FWS queueing configurable.")
Tested-by: Per Förlin <per.forlin@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memory is malloced in mwifiex_cfg80211_start_ap() and should be
freed before leaving from the error handling cases, otherwise it
will cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/marvell/libertas/cfg.c:2047:5: warning:
symbol 'lbs_set_power_mgmt' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding this opcode, allows the TI wireless driver,
to report throughput directly from FW to mac80211.
This is used mainly for mesh metric calculation.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[kvalo@codeaurora.org: fix indentation]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.
This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was succesfully tested with 4366B1. A small workaround is needed
for the main interface otherwise it would stuck at the hidden state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dependencies were impossible to handle preventing
drivers for CDC devices not which are not network drivers
from using the common parser.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in bfin_mac_ethtool_setsettings,
but this check is already done in dev_ethtool, so no need to repeat
it before calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
A dedicated workqueue has been used since the workitem viz
lp->txtimeout_reinit is involved in reinitialization if a TX timeout
occurs, which is necessary to guarantee forward progress in packet
processing. As a network device can be used during memory reclaim, the
workqueue needs forward progress guarantee under memory pressure.
WQ_MEM_RECLAIM has been set to ensure this.
Since there is only a single work item, explicit concurrency limit is
unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The label lio_xmit_failed is used 3 times through liquidio_xmit() but it
always makes a call to dma_unmap_single() using potentially
uninitialized variables from "ndata" variable. Out of the 3 gotos, 2 run
after ndata has been initialized, and had a prior dma_map_single() call.
Fix this by adding a new error label: lio_xmit_dma_failed which does
this dma_unmap_single() and then processed with the lio_xmit_failed
fallthrough.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Reported-by: coverity (CID 1309740)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case nb8800_receive() fails to allocate a fragment, we would leak the
SKB freshly allocated and just return, instead, free it.
Reported-by: coverity (CID 1341750)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be using a logical check here instead of a bitwise operation
to check if the device is closed already in et131x_tx_timeout().
Reported-by: coverity (CID 146498)
Fixes: 38df6492eb ("et131x: Add PCIe gigabit ethernet driver et131x to drivers/net")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver.
The FEMAC supports max speed 100Mbps and has been used in many
Hisilicon SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So
there is no reason to have this symbol visible.
A further optimisation would be to put the code for both symbols into a
single module which would allow to not export at least cpsw_phy_sel()
and simplify the module load process.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was used err_xxx for labeled statement, it is
not easy to understand, now use free_xxx for labeled
statement.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices of the same type all export the same, random MAC address. This
behavior has been seen on the ZTE MF910, MF823 and MF831, and there are
probably more devices out there. Fix this by generating a valid random MAC
address if we read a random MAC from device.
Also, changed the memcpy() to ether_addr_copy(), as pointed out by
checkpatch.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in cpmac_set_settings, but this
check is already done in dev_ethtool, so no need to repeat it before
calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in au1000_set_settings, but this
check is already done in dev_ethtool, so no need to repeat it before
calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets entering the switch are mapped to a Switch Priority (SP)
according to their PCP value (untagged frames are mapped to SP 0).
The packets are classified to a priority group (PG) buffer in the port's
headroom according to their SP.
The switch maintains another mapping (SP to IEEE priority), which is
used to generate PFC frames for lossless PGs. This mapping is
initialized to IEEE = SP % 8.
Therefore, when mapping SP 'x' to PG 'y' we create a situation in which
an IEEE priority is mapped to two different PGs:
IEEE 'x' ---> SP 'x' ---> PG 'y'
IEEE 'x' ---> SP 'x + 8' ---> PG '0' (default)
Which is invalid, as a flow can use only one PG buffer.
Fix this by mapping both SP 'x' and 'x + 8' to the same PG buffer.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of supported traffic classes that can have ETS and PFC
simultaneously enabled is not subject to user configuration, so make
sure we always initialize them to the correct values following a set
operation.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't have PAUSE frames and PFC both enabled on the same port, but
the fact that ieee_setpfc() was called doesn't necessarily mean PFC is
enabled.
Only emit errors when PAUSE frames and PFC are enabled simultaneously.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device supports link autonegotiation, so let the user know about it
by indicating support via ethtool ops.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a new speed we need to disable and enable the port for the
changes to take effect. We currently only do that if the operational
state of the port is up. However, setting a new speed following link
training failure will require us to explicitly set the port down and then
up.
Instead, disable and enable the port based on its administrative state.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch switch to use skb array instead of sk_receive_queue to
avoid spinlock contentions. Tests shows about 21% improvements for
guest rx pps:
Before: 1472731 pkts/s
After: 1786289 pkts/s
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We decide the rxq through calculating its hash which is not necessary
if we only have one rx queue. So this patch skip this and just return
queue 0. Test shows 22% improving on guest rx pps.
Before: 1201504 pkts/s
After: 1472731 pkts/s
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-07-14
This series contains fixes to i40e and ixgbe.
Alex fixes issues found in i40e_rx_checksum() which was broken, where the
checksum was being returned valid when it was not.
Kiran fixes a bug which was found when we abruptly remove a cable which
caused a panic. Set the VSI broadcast promiscuous mode during VSI add
sequence and prevents adding MAC filter if specified MAC address is
broadcast.
Paolo Abeni fixes a bug by returning the actual work done, capped to
weight - 1, since the core doesn't allow to return the full budget when
the driver modifies the NAPI status.
Guilherme Piccoli fixes an issue where the q_vector initialization
routine sets the affinity _mask of a q_vector based on v_idx value.
This means a loop iterates on v_idx, which is an incremental value, and
the cpumask is created based on this value. This is a problem in
systems with multiple logical CPUs per core (like in SMT scenarios).
Changed the way q_vector's affinity_mask is created to resolve the issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i provides a driver version that is hard coded.
Export the same value via "modinfo".
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a 2 byte struct whole after line.loopback so we need to clear
that out to avoid disclosing stack information.
Fixes: c19b6d246a ('drivers/net: support hdlc function for QE-UCC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the q_vector initialization routine sets the affinity_mask
of a q_vector based on v_idx value. Meaning a loop iterates on v_idx,
which is an incremental value, and the cpumask is created based on
this value.
This is a problem in systems with multiple logical CPUs per core (like in
SMT scenarios). If we disable some logical CPUs, by turning SMT off for
example, we will end up with a sparse cpu_online_mask, i.e., only the first
CPU in a core is online, and incremental filling in q_vector cpumask might
lead to multiple offline CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
This patch changes the way q_vector's affinity_mask is created: it iterates
on v_idx, but consumes the CPU index from the cpu_online_mask instead of
just using the v_idx incremental value.
No functional changes were introduced.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function ixgbe_poll() returns 0 when it clean completely
the rx rings, but this foul budget accounting in core code.
Fix this returning the actual work done, capped to weight - 1, since
the core doesn't allow to return the full budget when the driver modifies
the napi status
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets VSI broadcast promiscuous mode during VSI add sequence
and prevents adding MAC filter if specified MAC address is broadcast.
Change-ID: Ia62251fca095bc449d0497fc44bec3a5a0136773
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a couple of issues I found in i40e_rx_checksum while doing some
recent testing. As a result I have found the Rx checksum logic is pretty
much broken and returning that the checksum is valid for tunnels in cases
where it is not.
First the inner types are not the correct values to use to test for if a
tunnel is present or not. In addition the inner protocol types are not a
bitmask as such performing an OR of the values doesn't make sense. I have
instead changed the code so that the inner protocol types are used to
determine if we report CHECKSUM_UNNECESSARY or not. For anything that does
not end in UDP, TCP, or SCTP it doesn't make much sense to report a
checksum offload since it won't contain a checksum anyway.
This leaves us with the need to set the csum_level based on some value.
For that purpose I am using the tunnel_type field. If the tunnel type is
GRENAT or greater then this means we have a GRE or UDP tunnel with an inner
header. In the case of GRE or UDP we will have a possible checksum present
so for this reason it should be safe to set the csum_level to 1 to indicate
that we are reporting the state of the inner header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'vr' should be a valid pointer here, so returning 'PTR_ERR(vr)' is wrong.
Return an explicit error code (-ENOENT) instead.
Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXhmR1AAoJEG4XJFUm622bn+gH/Ar5l/oU76nmXKh0xNiV6bUE
2FuRV9X7ynAOLbFJfqZvN8eL1kTyztXOpxVOt9xLZvNcrJP2mdOH+YdUpSPk/XRw
mpFC7RCln/Y1bbX02la7V8iRJlKK1/VmdMABJXsalDcxSPMhhBQtr4/ZC7NcgmeJ
zKCZDGr/x4qpmAkYGsf3msJsBotHtt9xuHp4fFswp9Gpm+VeqtdqGEeMxowoILRK
QBj6nZIuLI4PMnJhfCJn94t9D/AVUIVJTeuWNDS5Up4gZVFo9SlpnkR520P0IY4Q
1238g5sAdKqONsPO0lyUacUlY2cTafDr4kD6UKnjf659KDd49MDJArpfbvMeweY=
=PTV+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.8
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e826eafa65 ("bonding: Call netif_carrier_off after
register_netdevice") moved netif_carrier_off() from bond_init() to
bond_create(), but the latter is called only for initial default
devices and ones created through sysfs:
$ modprobe bonding
$ echo +bond1 > /sys/class/net/bonding_masters
$ ip link add bond2 type bond
$ grep "MII Status" /proc/net/bonding/*
/proc/net/bonding/bond0:MII Status: down
/proc/net/bonding/bond1:MII Status: down
/proc/net/bonding/bond2:MII Status: up
Ensure that carrier is initially off also for devices created through
netlink.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF representors support only TC filter/action offloads
(not mqprio) and this is enabled for them by default.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the TC offload code such that when the eswitch exists and it's
mode being SRIOV offloads, we do TC actions parsing and setup targeted
for eswitch. Next, we add the offloaded flow to the HW e-switch (fdb).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the setup code that parses the TC actions needed to support offloading drop
and mirred/redirect for SRIOV e-switch. We can redirect between two devices if
they belong to the same HW switch, compare the switchdev HW ID attribute to
enforce that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Towards reusing the TC offloads code for an SRIOV use-case, change some of the
helper functions to have _nic in their names so it's clear what's NIC unique
and what's general. Also group together the NIC related helpers so we can easily
branch per the use-case in downstream patch.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows for upper levels in the driver, e.g the TC offload code to add
e-switch offloaded steering rules. The caller provides the rule spec for
matching, action, source and destination vports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the offloads mode, some slow path rules are added by the driver (e.g
send-to-vport), while offloaded rules are to be added from upper layers.
The slow path rules have lower priority and we don't want matching on
offloaded rules to suffer from extra steering hops related to the slow
path rules.
We use two priorities, one for offloaded rules (fast path), and one for
the control rules (slow path). To allow for that, we enable two priorities
for the FDB namespace in the FS core code.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenly, the code that programs the flow actions into the firmware
doesn't check if was actually asked to offload the statistics, fix that.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit utilize the ability of ConnectX-4 to bulk read flow counters.
Few bulk counter queries could be done instead of issuing thousands of
firmware commands per second to get statistics of all flows set to HW,
such as those programmed when we offload tc filters.
Counters are stored sorted by hardware id, and queried in blocks (id +
number of counters).
Due to hardware requirement, start of block and number of counters in a
block must be four aligned.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use bulk counters, we need to have counters sorted by id.
Signed-off-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline function that checks if there is a pending tx packet.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-07-13
Here's our main bluetooth-next pull request for the 4.8 kernel:
- Fixes and cleanups in 802.15.4 and 6LoWPAN code
- Fix out of bounds issue in btmrvl driver
- Fixes to Bluetooth socket recvmsg return values
- Use crypto_cipher_encrypt_one() instead of crypto_skcipher
- Cleanup of Bluetooth connection sysfs interface
- New Authentication failure reson code for Disconnected mgmt event
- New USB IDs for Atheros, Qualcomm and Intel Bluetooth controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Start all tx queues (including inactive ones) when opening the netdev.
Stop all tx queues (including inactive ones) when closing the netdev.
This is a workaround for the tx timeout watchdog false alarm issue in
which the netdev watchdog is polling all the tx queues which may include
inactive queues and thus once lowering the real tx queues number
(ethtool -L) it will generate tx timeout watchdog false alarms.
Fixes: 3947ca1859 ('net/mlx5e: Implement ndo_tx_timeout callback')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change netif_tx_queue_stopped to netif_xmit_stopped. This will show
when queues are stopped due to byte queue limits.
Fixes: 3947ca1859 ('net/mlx5e: Implement ndo_tx_timeout callback')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the hardware can be doing zero padding, we want the SKB to
be going out on the wire with the appropriate size. This fixes packet
truncations observed with e.g: ARP packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case any operation fails before we can successfully go the point
where we would register a MDIO bus, we would be going to an error label
which involves unregistering then freeing this yet to be created MDIO
bus. Update all error paths to go to label free which is the only one
valid until either the clock is enabled, or the MDIO bus is allocated
and registered. This fixes kernel oops observed while trying to
dereference the MDIO bus structure which is not yet allocated.
Fixes: a170285772 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace EMAD messages going down to HW and up from HW. Devlink needs to be
registered before EMAD init so the trace function can be called
with valid devlink handle.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v1->v2:
- Use trace_devlink_hwmsg directly
Signed-off-by: David S. Miller <davem@davemloft.net>
During commit b54b8c2d6e
("net: ezchip: adapt driver to little endian architecture")
adapting to little endian architecture,
zeroing of controller was left out.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing clk_disable_unprepare() call before return
from dwceqos_probe() in the error handling case of invalid
fixed-link.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:79:5: warning:
symbol '_mtk_mdio_write' was not declared. Should it be static?
drivers/net/ethernet/mediatek/mtk_eth_soc.c:98:5: warning:
symbol '_mtk_mdio_read' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iwl-debug.h header relies in implicit inclusion of linux/device.h and
we get a lot of warnings without that:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:23: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.h:66:0,
from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:68:
drivers/net/wireless/intel/iwlwifi/iwl-trans.h: In function 'iwl_trans_tx':
drivers/net/wireless/intel/iwlwifi/iwl-trans.h:1030:348: error: passing argument 1 of '__iwl_err' from incompatible pointer type [-Werror=incompatible-pointer-types]
IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
^
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:67:0:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:6: note: expected 'struct device *' but argument is of type 'struct device *'
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~~~~
The easiest workaround is to just declare 'struct device' before its first use,
rather than including the entire header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 21cb3222fe ("iwlwifi: decouple PCIe transport from mac80211")
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
isr function issues SPI read command to mrf to obtain INTSTAT.
SPI transfer is 2 bytes, but value of 2nd byte is not defined.
This had the effect that only the first ISR worked as intended. The
second ISR read incorrect INTSTAT values. Observed on Raspberry PI B+.
Signed-off-by: Walter Mack <wmack@componentsw.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8153-AD supports a persistent system specific MAC address.
This means a device plugged into two different systems with host side
support will show different (but persistent) MAC addresses.
This information for the system's persistent MAC address is burned in when
the system HW is built and available under \_SB.AMAC in the DSDT at runtime.
This technology is currently implemented in the Dell TB15 and WD15 Type-C
docks. More information is available here:
http://www.dell.com/support/article/us/en/04/SLN301147
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/b53/b53_srab.c: In function 'b53_srab_probe':
>> drivers/net/dsa/b53/b53_srab.c:388:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
pdata->chip_id = (u32)of_id->data;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
idx can be returned as -ENOSPC, so we should check for this first
before using it as an index into nn->vxlan_usecnt[] to avoid an
out of bounds array offset read.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable lan91x adapters in some ARM machines and models
when booted with an ACPI kernel.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4386f5662e ("net: ethernet: bcmgenet: use
phy_ethtool_{get|set}_link_ksettings")
This patch is wrong, the function phy_ethtool_{get|set}_link_ksettings
don't check if the device is running, but the driver bcmgenet need this
check.
The function {get|set}_settings need to access the mdio bus, and this
bus may only be used when the device is running. Otherwise, the clock
is disable and a mdio access will fail.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcma portion of the driver has been split off into a bcma specific
driver. This has been mirrored for the platform driver. The last
references to the bcma core struct have been changed into a generic
function call. These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver. In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct. In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus. This will help with the upcoming BCMA
removal from the bgmac driver. Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.
Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present. In
addition to the moving of the driver, this reset function is added.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. So,
simply change all of the bgmac_* prints to their dev_* counterparts. In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90186af404 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates as static checker warning because htons(ETH_P_IPV6)
is always true. From the context it looks like the && was intended to
be !=.
Fixes: 94758f8de0 ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd2 ("ppp: take reference on channels netns")
Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new APIs for eliminating a copy on the receive path. These new APIs also
help in minimizing the number of memory barriers we end up issuing (in the
ringbuffer code) since we can better control when we want to expose the ring
state to the host.
The patch is being resent to address earlier email issues.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
