Add the new A33 SS compatible to the crypto node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the SPI device nodes were added, they were added in the wrong
location in the device tree file. The device nodes should be sorted
by register address.
Move the devices node to their correct positions within the file.
Fixes: 554581b791 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the SPI device nodes were added, SPI2 and SPI3 had incorrect
register base addresses.
Fix the base address for both of them.
Fixes: 554581b791 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Reported-by: JuanEsf <juanesf91@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318 ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Recent changes in the SPI core and the SPI-GPIO driver revealed that the
GPIO lines for the LD9040 LCD controller on the UniversalC210 board are
defined incorrectly. Fix the polarity for those lines to match the old
behavior and hardware requirements to fix LCD panel operation with
recent kernels.
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: amba: $nodename:0:
'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When we combine spi-rockchip.yaml and
spi-controller.yaml and add 'additionalProperties: false'
it gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: spi@10270000:
'#dma-cells' does not match any of the regexes:
'^.*@[0-9a-f]+$', '^slave$'
'#dma-cells' are not used for dma clients, so remove them all.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309134020.14935-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
for example this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: mmc@1021c000:
'default-sample-phase' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'default-sample-phase' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'rockchip,default-sample-phase'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: mmc@10218000:
'vmmcq-supply' does not match any of the regexes:
'^.*@[0-9]+$',
'^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$',
'pinctrl-[0-9]+'
'vmmcq-supply' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i.MX25's Keypad Port (KPP) can be used with a key pad matrix of up to
8 x 8 keys. Add pin configurations for rows 4 to 7.
The new defines have been tested on an out-of-tree board.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto node should use the "crypto" generic naming,
and not a specific one ("sahara", "dcp", "caam").
Child nodes of the crypto node for caam crypto engine
should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW5910-C revision adds a TI CC1352 connected to IMX UART4
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In one of the iWave-G22D development board variants, called Generic SODIMM
Development Platform, we have an LCD with touchscreen. The resistive touch
controller, STMPE811 is on the development board and is connected through
the i2c5 of the RZ-G1E.
Additionally, this controller should generate an interrupt to the CPU and
it is connected through GPIO4,4 to the GIC.
Touch was tested with one of our iW-RainboW-G22D-SODIMM RZ/G1E development
platforms.
More details on the iWave website:
https://www.iwavesystems.com/rz-g1e-sodimm-development-kit.html
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583336650-25848-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the Generic SODIMM Development Platform there is an RGB LCD panel
directly connected to the DU output. It uses the TPU0 as backlight, one
GPIO pull-up configuration for power enable, R[2:7], G[2:7], B[2:7],
VSYNC, HSYNC, DU0_DISP and, DU0_CLK as inputs.
There is no encoder between the DU and the panel, therefore the default
connector driver is used.
The two variants of the iW-G22D should be mutually exclusive, therefore
this patch also disables the RGB LCD display when the HDMI extension board
is used.
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583239490-8837-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pmic is a mfd device and supports gpios. Those gpios are not routed
to the SoM baseboard pin header but they are connected to the i.MX6. We
need the GPIO's to configure the pmic to select between the
suspend/resume arm and soc voltages
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default the phycore-som has support for two watchdog devices: 1st the
internal imx6 watchdog and 2nd the DA9062 PMIC watchdog. According [1]
the PMIC watchdog is used as boot watchdog. It is common to use this
watchdog during "system up" time too. Furthermore the PMIC watchdog can
be used to address ERR007117 since the phycore-som can be equipped with
NAND or eMMC storage.
The PMIC watchdog can be enabled/disabled by the PMIC itself if the PMIC
enters POWERDOWN mode or by the host. The PMIC powerdown mode can't be
used due to the PCB design. So the watchdog is still enabled during a
suspend which causes a system reset. We need to tell the driver to
disable the watchdog during a system suspend and to reenable it upon a
resume to fix this.
[1] https://git.pengutronix.de/cgit/barebox/tree/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi#n73
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX6/7 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX7, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCI support.
Since this board has an active high PCI reset line, pass the
'reset-gpio-active-high' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200117230845.25190-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Depending on bcm2711's revision its emmc2 controller might have
different DMA constraints. Raspberry Pi 4's firmware will take care of
updating those, but only if a certain alias is found in the device tree.
So, move emmc2 into its own bus, so as not to pollute other devices with
dma-ranges changes and create the emmc2bus alias.
Based in Phil ELwell's downstream implementation.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200304132437.20164-1-nsaenzjulienne@suse.de
Commit a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A test with the command below gives these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-r89.dt.yaml: /: 'model'
is a required property
Fix this error by adding the missing model properties to
the involved dts files.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/root-node.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200304074051.8742-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The AM57xx family of SoCs contains two identical PRU-ICSS instances
that have a very unique SYSC register. The IPs do not have any
PRCM reset lines unlike those on AM33xx/AM437x SoCs. Add the PRUSS
interconnect target-module nodes with all the required properties.
Each of the PRUSS devices themselves shall be added as child nodes
to the corresponding interconnect node in the future. The PRU-ICSS
instances are only available on AM57xx family of SoCs and are not
supported on DRA7xx family of SoCs in general, so the target module
nodes are added in a separate dtsi file. This new dtsi file is
included in all the AM57xx SoC dtsi files, so the nodes are
automatically inherited and enabled on all AM57xx boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM437x family of SoCs contains two dissimilar PRU-ICSS instances,
but leverage a common reset line and SYSCFG from the larger PRU-ICSS1
instance. This SYSC register has also very unique bit-fields. Both
the IPs require the PRCM reset to be deasserted to be able to access
any registers. Add a common PRUSS interconnect target-module with all
the required properties.
The PRUSS devices themselves shall be added as child nodes to this
interconnect node in the future. The PRU-ICSS instances are not
supported on AM4372 SoC though in the AM437x family, so the target
module node should be disabled in any derivative board files that
use this SoC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on some AM33xx SoCs has a very unique SYSC
register. The IP also uses a hard-reset line, and requires this
PRCM reset to be deasserted to be able to access any registers.
Update the existing PRUSS interconnect target-module with all
the required properties.
The PRUSS device itself shall be added as a child node to this
interconnect node in the future. PRU-ICSS is not supported on
AM3351/AM3352/AM3354 SoCs though in the AM33xx family, so the
target module node should be disabled in derivative board files
that use any of these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Note that we also fix a harmless typo for the node name, it's
dispc@400, not dispc@4000.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.
To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Note that we must disable smart idle modes for HDMI audio like we've
done with the legacy platform data. And HDMI needs both hdmi clock
and dss clock to operate.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
The display subsystem (DSS) is in a 16MB interconnect target module
mapped to l4 and l3 buses. We are only using the l3 port as recommended
by the TRM. So there is no need to configure l4 ranges like we've done
for l4 ABE instance for example.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Let's also add add a note about using only the l3 access without l4
as noted in the TRM.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IB2 syscon should not have any funny names, just call
it syscon@ as per the convention so the schema will apply
properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'dma-ranges' at the top level doesn't make sense. 'dma-ranges' implies
there is a parent bus node with '#address-cells' and '#size-cells' which
is impossible here.
Likely this translation needs to be moved down to sub-nodes that need
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for RGMII mode")
caused a regression for dm814x boards where NFSroot would no longer work.
Let's fix the issue by configuring "rgmii-id" mode as internal delays are
needed that is no longer the case with "rgmii" mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add vcc50_hdmi regulator for Vyasa RK3288 board.
VCC50_HDMI is the real name used for this regulator as
per the schematics.
This regulator used for HDMI connector by detecting the
cable via HDMI_EN gpio and input rails are sourced from
VSUS_5V regulator.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200123134641.30720-3-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to hardware schematics of Vyasa RK3288 the
actual name used for vcc10_lcd is vdd10_lcd.
regulator suspend voltage can rail upto 1.0V not 1.8V.
Fix the name and suspend voltage for vcc10_lcd regulator.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200123134641.30720-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
'rockchip-pmu-sram.txt' inherit properties from 'sram.yaml'.
Fix this error by adding 'sram' to the bus_intmem nodename
in 'rk3288.dtsi'. But 'sram' is also a node name already in use.
To prevent confusion rename it to 'pmu_sram'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rk3036-evb.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rk3036-kylin.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
Fix this error by adding sram to the bus_intmem nodename
in rk3036.dtsi.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rv1108-evb.dt.yaml:
bus_intmem@10080000: $nodename:0: 'bus_intmem@10080000'
does not match '^sram(@.*)?'
Fix this error by adding sram to the bus_intmem nodename
in rv1108.dtsi.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml: usb@30180000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@30180000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3228-evb.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3229-evb.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rk3229-xms6.dt.yaml: usb@30040000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
'g-use-dma' is not a valid option in dwc2.yaml, so remove it
from all Rockchip dtsi files.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
g-use-dma was deprecated in november 2016, see
https://patchwork.kernel.org/patch/9420553/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228113922.20266-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
5.6, please pull the following:
- Stefan adds missing Device Tree properties for the Raspberry Pi 3B and
4 LEDs to have proper default configuration
- Nicolas adds an alias for the PCIe root complex node that is looked up
by the Raspberry Pi firmware for patching in specific properties
-----BEGIN PGP SIGNATURE-----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=On3Q
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.6/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.6, please pull the following:
- Stefan adds missing Device Tree properties for the Raspberry Pi 3B and
4 LEDs to have proper default configuration
- Nicolas adds an alias for the PCIe root complex node that is looked up
by the Raspberry Pi firmware for patching in specific properties
* tag 'arm-soc/for-5.6/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
Link: https://lore.kernel.org/r/20200228181144.15148-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
-----BEGIN PGP SIGNATURE-----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=UHKz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few fixes for omaps for v5.6-rc cycle
This series of changes contains few code fixes for issues
recently discovered:
- A build fix for ARMv6 only configs when CONFIG_HAVE_ARM_SMCCC is
not set
- A fix for ti-sysc quirk handling for 1-wire hdq reset
And a handful of dts fixes that I had queued up and should
have already sent earlier instead of waiting for the code
fixes to get sorted out:
- Fix naming of vsys_3v3 regulator for dra7-evm
- Fix incorrect OPP node names for am437x-idk-evm
- Fix IPU1 mux clock parent source for dra7
- Add missing PWM property for dra7 timers 13 to 16
- Add missing dma-ranges for dra7 PCIe nodes
- Fix mmc3 max-frequency for dra76x
* tag 'omap-for-v5.6/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: dra7-l4: mark timer13-16 as pwm capable
ARM: dts: dra7xx-clocks: Fixup IPU1 mux clock parent source
ARM: dts: am437x-idk-evm: Fix incorrect OPP node names
ARM: dts: dra7-evm: Rename evm_3v3 regulator to vsys_3v3
Link: https://lore.kernel.org/r/pull-1582903541-589933@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
G3D power domain in Exynos5420 SoC is supplied from PVDD_G3DS_1V0 and
PVDD_G3D_1V0. Besides the main GPU MALI module it also contains the power
domain control logic and clocks. Turning the power supplies off causes
the power domain to fail to operate properly if GPU drivers are loaded as
modules. GPU should use PVDD_G3D_1V0 supply mainly to control the DVFS.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
G3D power domain in Exynos5422 SoC is supplied from VDD_G3D. Besides the
main GPU MALI module it also contains the power domain control logic and
clocks. Turning the VDD_G3D power supply off causes the power domain to
fail to operate properly and breaks for example system suspend/resume.
GPU should use VDD_G3D supply mainly to control the DVFS.
Fixes: 1a5a85c564 ("ARM: dts: exynos: Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The following commit:
c7225494b ("efi/arm: Work around missing cache maintenance in decompressor handover")
modified the EFI handover code written in assembler to work around the
missing cache maintenance of the piece of code that is executed after the
MMU and caches are turned off.
Due to the fact that this sequence incorporates a subroutine call, cleaning
that code from the cache is not a matter of simply passing the start and end of
the currently running subroutine into cache_clean_flush(), which is why
instead, the code jumps across into the cleaned copy of the image.
However, this assumes that this copy is executable, and this means we
expect EFI_LOADER_DATA regions to be executable as well, which is not
a reasonable assumption to make, even if this is true for most UEFI
implementations today.
So change this back, and add a cache_clean_flush() call to cover the
remaining code in the subroutine, and any code it may execute in the
context of cache_off().
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20200228121408.9075-5-ardb@kernel.org
Commit 73f9de0c7f ("ARM: dts: uniphier: Add generic compatible string
for I2C EEPROM") did not touch this node.
Add the compatible string prefixed "atmel," so that this matches to the
OF table.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern
"^(cache-controller|cpu)(@[0-9a-f,]+)*$" defined in
schemas/cache-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
l2-cache@500c0000: $nodename:0: 'l2-cache@500c0000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^nand-controller(@.*)?" defined
in Documentation/devicetree/bindings/mtd/nand-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
nand@68000000: $nodename:0: 'nand@68000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^interrupt-controller(@[0-9a-f,]+)*$"
defined in schemas/interrupt-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
make ARCH=arm dtbs_check' will show warnings like this:
aidet@5fc20000: $nodename:0: 'aidet@5fc20000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^mmc(@.*)?$" defined in
Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm dtbs_check' will show warnings like this:
sdhc@5a000000: $nodename:0: 'sdhc@5a000000' does not match '^mmc(@.*)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some bcm2711 revisions have different DMA constraints on the their PCIE
bus. The lower common denominator, being able to access the lower 3GB of
memory, is the default setting for now. Newer SoC revisions are able to
access the whole memory space.
Raspberry Pi 4's firmware is aware of this limitation and will correct
the PCIE's dma-ranges property if a pcie0 alias is available. So add
it.
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the missing properties to the PWR LED for the RPi 3 & 4 boards,
which are already set for the other boards. Without them we will lose
the LED state after suspend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXlY78AAKCRCKwlD9ZEnx
cAR9APdKGcY7roK82m1uLIsCohHOdwikY4qvR+cVniRKgwspAP9Q3NNCXhelEEed
S2JMLficspDnR+BuWR3gyg173Z74CQ==
=P/qq
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas Fixes for v5.6
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
* tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
arm64: defconfig: Replace ARCH_R8A7796 by ARCH_R8A77960
Link: https://lore.kernel.org/r/20200226105236.18368-1-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
The OMAP4 DSP hwmod is used in DT, but the DT node is not
probing any real driver. The DSP device-tree node shall be
updated as per the new OMAP remoteproc bindings with the
underneath MMU device relying on the ti-sysc infrastructure.
Drop the legacy hwmod data for the DSP device along with the
custom ti,hwmods property. They have to be dropped together
since the early platform data init code is based on the custom
ti,hwmods property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add idle_states table for CPU on am437x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add idle_states table for CPU on am335x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a second PWM unit available in the PL I/O block.
Add a node and pinmux definition for it.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Update the v7 cache_clean_flush routine to take into account the
memory range passed in r0/r1, and perform cache maintenance by
virtual address on this range instead of set/way maintenance, which
is inappropriate for the purpose of maintaining the cached state of
memory contents.
Since this removes any use of the stack in the implementation of
cache_clean_flush(), we can also drop some code that manages the
value of the stack pointer before calling it.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for turning the decompressor's cache clean/flush
operations into proper by-VA maintenance for v7 cores, pass the
start and end addresses of the regions that need cache maintenance
into cache_clean_flush in registers r0 and r1.
Currently, all implementations of cache_clean_flush ignore these
values, so no functional change is expected as a result of this
patch.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Before adding another reference to the inflated image size, factor
out the slightly complicated way of loading the unaligned little-endian
constant from the end of the compressed data.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The last 8MB of physical memory on Artik520 family boards is reserved for
secure firmware. Adjust the total amount of the memory defined in
exynos3250-artik5.dtsi to match the memory available for the Linux kernel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5 ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEnNKg2mrY9zMBdeK7wjcgfpV0+n0FAl5S7WYACgkQwjcgfpV0
+n1jmQgAmwV3V8pbgB4mi4P2Mv8w5Zj5feUe6uXnTR2AFv5nygLcTzdxN+TU/6lc
OmZv2zzdsAscYlhuUdI/4t4cXIjHAZI39+UBoNRuMqKbkbvXCFscZANLxvJjHjZv
FFbgUk0DXkF0BCEDuSLNavidAv4b3gZsOmHbPfwuB8xdP05LbvbS2mf+2tWVAi2z
ULfua/0o9yiwl19jSS6iQEPCvvLBeBzTLW7x5Rcm/S0JnotzB59yMaeqD7jO8JYP
5PvI4WM/l5UfVHnZp2k1R76AOjReALw8dQgqAsT79Q7+EH3sNNuIjU6omdy+DFf4
tnpwYfeLOaZ1SztNNfU87Hsgnn2CGw==
=pDE3
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
Pull EFI updates for v5.7 from Ard Biesheuvel:
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This enables passive cooling by down-regulating CPU voltage
and frequency.
For the trip points, I used values from the BSP code directly.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This enables passive cooling by down-regulating CPU voltage
and frequency.
For trip points, I used a slightly lowered values from the BSP
code. The critical temperature of 110°C from BSP code seemed
like a lot, so I rounded it off to 100°C.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the gpio-ranges property to almost all of
the Qualcomm ARM platforms that utilize the pinctrl-msm
framework.
The gpio-ranges property is part of the gpiolib subsystem.
As a result, the binding text is available in section
"2.1 gpio- and pin-controller interaction" of
Documentation/devicetree/bindings/gpio/gpio.txt
For more information please see the patch titled:
"pinctrl: msm: fix gpio-hog related boot issues" from
this series.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr> [ipq4019]
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200108125455.308969-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5TuEMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4a+Qf9Enb2G47LTMeYH5JYhm2anDQ4lz+8
Og1bcGPYKilDhc4YzpAIhRnOTLa9TietZSS0tyNFk37GDfKRjn9gxXDRbI+4lrJc
UOSLpWCB4BnzKc+FoCHC37jkdkMD3V2E5MmFHtYkGYmH0DAi8cLmGebmgGujd0GJ
lx2/5EbxKoJxeA2i79H5OAPBhglJsEnPTSulZ+jUdLzJfBlRBIQBc3oPcwnRIibr
VUbLc4Gkb2kTe6NwdQTjqI+4BTHv7/4m+twOojO5Z8QBH4X+3bkLnLiylhuqHBeR
cDXGL7sHkekZhDQ3OwIMiT/5cc8SxplqAl6QMm8+/9gq7KfAucy8Psokow==
=dg69
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.
This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.
The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.
After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.
The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.
For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.
-----BEGIN PGP SIGNATURE-----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=Pox9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix LCD backlight issue for droid4
There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.
This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.
The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.
After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.
The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.
For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.
* tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: droid4: Configure LED backlight for lm3532
backlight: add led-backlight driver
Link: https://lore.kernel.org/r/pull-1582303901-96693@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We are missing AESS for omap5. Looks like it's similar to what we have
for omap4, and this gets ti-sysc interconnect target module driver to
detect it properly.
Note that we currently have no child device driver available for it.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "renesas,rcar-sata" compatible value was deprecated by
"renesas,sata-r8a7779" many years ago, in commit e67adb4e66
("sata_rcar: Add R-Car Gen2 SATA PHY support"). Drop it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200219153929.11073-1-geert+renesas@glider.be
Add reset control properties to the devices node for the Display Units
on all supported RZ/G1 SoCs. Note that on these SoCs, there is only a
single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-3-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen2 SoCs. Note that on these SoCs, there is
only a single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-2-geert+renesas@glider.be
The DU DT bindings have been updated to drop the reg-names property.
Update the r8a7745 device tree accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218132217.21454-1-geert+renesas@glider.be
USB-ID signal has a pullup on the schematic, but in reality it's not
pulled up, so add a GPIO pullup. And we also need a usb0_vbus_power-supply
for VBUS detection.
This fixes OTG mode detection and charging issues on TBS A711 tablet.
The issues came from ID pin reading 0, causing host mode to be enabled,
when it should not be, leading to DRVVBUS being enabled, which disabled
the charger.
Fixes: f2f221c781 ("ARM: dts: sun8i: a711: Enable USB OTG")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Property dr_mode = "otg" is the default in sun8i-a83t.dtsi
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
What works:
- Serial console
- mmc0, mmc2 (both microSD card slots on the board)
- All buttons (gpio and lradc based)
- Power LED
- PMIC
- RTC
- USB OTG/gadgets mode
- Realtek USB WiFi
- Display backlight
- eInk display SPI NOR flash memory
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Node name should be generic, use "ocotp-ctrl" instead of "ocotp"
for all i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "watchdog" instead of "wdog" for
wdog nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have added new ways to load the initrd or the mixed mode
kernel, we will also need a way to tell the loader about this. Add
symbolic constants for the PE/COFF major/minor version numbers (which
fortunately have always been 0x0 for all architectures), so that we
can bump them later to document the capabilities of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The fixed regulators defined for Arndale5250 boards have no control lines,
so mark them as 'always-on' to better describe the hardware and also kill
the strange messages like 'MAIN_DC: disabling' after boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to the schematic, both eMMC and SDMMC use dedicated fixed
regulators connected directly to the DC5V and MAIN_DC rails. Remove the
GPX1-1 line assigned to the MMC regulator, because such control
connection doesn't exist. Also change its name to VDD_MMC to avoid
conflict with LDO18 output of S5M8767 PMIC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Expose efi_entry() as the PE/COFF entrypoint directly, instead of
jumping into a wrapper that fiddles with stack buffers and other
stuff that the compiler is much better at. The only reason this
code exists is to obtain a pointer to the base of the image, but
we can get the same value from the loaded_image protocol, which
we already need for other reasons anyway.
Update the return type as well, to make it consistent with what
is required for a PE/COFF executable entrypoint.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for turning the decompressor's cache clean/flush
operations into proper by-VA maintenance for v7 cores, pass the
start and end addresses of the regions that need cache maintenance
into cache_clean_flush in registers r0 and r1.
Currently, all implementations of cache_clean_flush ignore these
values, so no functional change is expected as a result of this
patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The EFI stub executes within the context of the zImage as it was
loaded by the firmware, which means it is treated as an ordinary
PE/COFF executable, which is loaded into memory, and cleaned to
the PoU to ensure that it can be executed safely while the MMU
and caches are on.
When the EFI stub hands over to the decompressor, we clean the caches
by set/way and disable the MMU and D-cache, to comply with the Linux
boot protocol for ARM. However, cache maintenance by set/way is not
sufficient to ensure that subsequent instruction fetches and data
accesses done with the MMU off see the correct data. This means that
proceeding as we do currently is not safe, especially since we also
perform data accesses with the MMU off, from a literal pool as well as
the stack.
So let's kick this can down the road a bit, and jump into the relocated
zImage before disabling the caches. This removes the requirement to
perform any by-VA cache maintenance on the original PE/COFF executable,
but it does require that the relocated zImage is cleaned to the PoC,
which is currently not the case. This will be addressed in a subsequent
patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The boot stub does not emit a .fixup section at all anymore, so remove
it.
Link: https://lore.kernel.org/lkml/202002080058.FD1DDB1@keescook/
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When using plugins, GCC requires that the -fplugin= options precedes
any of its plugin arguments appearing on the command line as well.
This is usually not a concern, but as it turns out, this requirement
is causing some issues with ARM's per-task stack protector plugin
and Kbuild's implementation of $(cc-option).
When the per-task stack protector plugin is enabled, and we tweak
the implementation of cc-option not to pipe the stderr output of
GCC to /dev/null, the following output is generated when GCC is
executed in the context of cc-option:
cc1: error: plugin arm_ssp_per_task_plugin should be specified before \
-fplugin-arg-arm_ssp_per_task_plugin-tso=1 in the command line
cc1: error: plugin arm_ssp_per_task_plugin should be specified before \
-fplugin-arg-arm_ssp_per_task_plugin-offset=24 in the command line
These errors will cause any option passed to cc-option to be treated
as unsupported, which is obviously incorrect.
The cause of this issue is the fact that the -fplugin= argument is
added to GCC_PLUGINS_CFLAGS, whereas the arguments above are added
to KBUILD_CFLAGS, and the contents of the former get filtered out of
the latter before being passed to the GCC running the cc-option test,
and so the -fplugin= option does not appear at all on the GCC command
line.
Adding the arguments to GCC_PLUGINS_CFLAGS instead of KBUILD_CFLAGS
would be the correct approach here, if it weren't for the fact that we
are using $(eval) to defer the moment that they are added until after
asm-offsets.h is generated, which is after the point where the contents
of GCC_PLUGINS_CFLAGS are added to KBUILD_CFLAGS. So instead, we have
to add our plugin arguments to both.
For similar reasons, we cannot append DISABLE_ARM_SSP_PER_TASK_PLUGIN
to KBUILD_CFLAGS, as it will be passed to GCC when executing in the
context of cc-option, whereas the other plugin arguments will have
been filtered out, resulting in a similar error and false negative
result as above. So add it to ccflags-y instead.
Fixes: 189af46571 ("ARM: smp: add support for per-task stack canaries")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
To use Energy Aware Scheduler (EAS) the Energy Model (EM) should be
registered for CPUs. Add dynamic-power-coefficient into CPU nodes which
let CPUFreq subsystem register the EM structures. This will increase
energy efficiency of big.LITTLE platforms.
The 'dynamic-power-coefficient' values have been obtained experimenting
with different workloads. The power measurements taken from big CPU
Cluster and LITTLE CPU Cluster has been compared with official documents
and synthetic workloads estimations. The effective power ratio between
Cortex-A7 and Cortex-A15 CPUs (~3x) is also aligned with documentation.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DMTimers 13 - 16 are PWM capable and also can be used for CPTS input
signals generation. Hence, mark them as "ti,timer-pwm".
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU1 functional clock is the output of a mux clock (represented
by ipu1_gfclk_mux previously) and the clock source for this has been
updated to be sourced from dpll_core_h22x2_ck in commit 39879c7d96
("ARM: dts: dra7xx-clocks: Source IPU1 functional clock from CORE DPLL").
ipu1_gfclk_mux is an obsolete clock now with the clkctrl conversion,
and this clock source parenting is lost during the new clkctrl layout
conversion.
Remove this stale clock and fix up the clock source for this mux
clock using the latest equivalent clkctrl clock. This restores the
previous logic and ensures that the IPU1 continues to run at the
same frequency of IPU2 and independent of the ABE DPLL.
Fixes: b5f8ffbb6f ("ARM: dts: dra7: convert to use new clkctrl layout")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable
OPP50 for MPU") adjusts couple of OPP nodes defined in the
common am4372.dtsi file, but used outdated node names. This
results in these getting treated as new OPP nodes with missing
properties.
Fix this properly by using the correct node names as updated in
commit b9cb2ba718 ("ARM: dts: Use - instead of @ for DT OPP
entries for TI SoCs").
Reported-by: Roger Quadros <rogerq@ti.com>
Fixes: 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable OPP50 for MPU")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the new schematics it is renamed and the same name is used on other
dra7 boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define pins for LVDS channels 0 and 1, configure reset line for tcon0 and
provide sample LVDS panel, connected to tcon0.
Signed-off-by: Andrey Lebedev <andrey@lebedev.lt>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The display DRC nodes have an assigned clocks property, while the driver
also enforces it.
Since assigned-clocks is pretty fragile anyway, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The display backend nodes have an assigned clocks property, while the driver
also enforces it.
Since assigned-clocks is pretty fragile anyway, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With the LED backlight changes merged, we still need the dts configured
to have backlight working for droid4. Based on an earlier patch from
Pavel Machek <pavel@ucw.cz>, let's configure the backlight but update
the value range to be more usable.
We have a range of 256 register values split into 8 steps, so we can
generate the brightness levels backwards with:
$ for i in 0 1 2 3 4 5 6 7; do echo "255 - ${i} * (256 / 8)" | bc; done
To avoid more confusion why the LCD backlight is still not on, let's
also enable LED backlight as a loadable module for omap2plus_defconfig.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DCE/DTE to UART pins macro defines to distinguish the
DCE and DTE functions, keep old defines at the end of file
for some time to make it backward compatible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The nodes with name scpsys actually implement a power-controller.
Rename the nodes to match the bindings description.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Node name should be generic, use "clock-controller" instead of
"ccm" for clks node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "keypad" instead of "kpp" for kpp node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "timer" instead of "gpt" for gpt node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per devicetree specification, generic names
are recommended to be used, such as bus.
i.MX AIPS is a AHB - IP bridge bus, so
we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/vf*.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sram-node compatible properties have mistakingly combined the
model-specific string with the generic "mtd-ram" string.
Note that neither "cy7c1019dv33-10zsxi, mtd-ram" or
"cy7c1019dv33-10zsxi" are used by any in-kernel driver and they are
not present in any binding.
The physmap driver will however bind to platform devices that specify
"mtd-ram".
Fixes: fc48e76489 ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds defines for another cspi3 configuration.
The defines have been tested on an out-of-tree board.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Increase boot partition size to 32MB to support bigger size kernel image
and FPGA bitstream.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The Testbox board is an open hardware enhancement for the Lamobo R1 router
board. The Testbox board is used in the CI-RT project to manage devices
under test (https://ci-rt.linutronix.de).
The hardware project is located at https://github.com/ci-rt/testbox-shield
The Testbox v2 expands the Lamobo R1 router board with
- a power supply,
- a CAN bus PHY,
- a power control,
- a relay,
- an I2C EEPROM,
- a secure key storage (ATECC608a) and
- two RS232 compliant serial ports.
Co-developed-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Bastian Germann <bage@linutronix.de>
[Maxime: Removed unused pinctrl node]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure that the priority of the RTCs is defined.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The max voltage of SW1A is 3.3V on PF3000 as per
http://cache.freescale.com/files/analog/doc/data_sheet/PF3000.pdf?fsrch=1&sr=1&pageNum=1
While at it, remove the unnecessary leading zero from
the i2c address.
Signed-off-by: André Draszik <git@andred.net>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri SODIMM numbers as GPIO line names on module level. The GPIO
lines with a name are all available on the SODIMM edge connector of the
Colibri iMX7 module and therefore a customer might use it as a GPIO. The
Toradex Evaluation Board has the SODIMM numbers printed on the silk-
screen. This allows a customer to quickly control a GPIO on a pin-header
by using the name printed next to it.
Putting the GPIO line name on module level makes sure that a customer
gets a reasonable default. If more meaningful names are available on a
custom carrier board, the user can overwrite the line names in a carrier
board level device tree.
The eMMC based modules share all GPIO names except two GPIOs on bank 6
which are not available on the raw NAND devices. Hence overwrite GPIO
line names of bank 6 in the eMMC specific device tree file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
Background discussion:
https://www.spinics.net/lists/stable/msg361156.html
Fixes: c7861adbe3 ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At imx7ulp evk, all USBOTG1 OC (Over Current) function pins are
used by others, and the USB driver doesn't support OC function
through the GPIO, so we disable the OC function for this board
as well as delete the pinctrl for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i.MX7D Document Number: IMX7DCEC Rev. 6, 03/2019,
there are only consumer/industrial parts, and 1.2GHz
is only support in consumer parts.
So exclude automotive from 792/996MHz/1.2GHz and exclude
industrial from 1.2GHz.
Fixes: d7bfba7296 ("ARM: dts: imx7d: Update cpufreq OPP table")
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After reset the oc protection polarity is set to active high on imx6.
If the polarity is not specified in device tree it is not changed.
The imx6dl-yapp4 platform uses an active-low oc signal so explicitly
configure that in the device tree.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the USB host port on the APx4 development board.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Documentation/devicetree/bindings/display/mxsfb.txt states that
the current display bindings format used in this dts is deprecated.
Convert it to the preferred DRM bindings instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the bluetooth found on the Nexus 5 phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: formatting cleanups; remove sleep clock; patch
extracted from much larger out of tree patch.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20200129232031.34538-4-masneyb@onstation.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add blsp2_uart10 node in order to support bluetooth on the Nexus 5
phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: use constants in interrupts property; patch
extracted from much larger out of tree patch.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20200129232031.34538-3-masneyb@onstation.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This exact node has been included in Amami DTS
ever since 2017, turns out it works perfectly
fine with Honami, as tested with postmarketOS.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200118165518.36036-1-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove "snps,phy-bus-name", "snps,phy-bus-id" and "snps,phy-addr"
properties which are deprecated.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add trip points and cooling maps for GPU thermal zone for Odroid
XU3/XU4/HC1 boards. Trip points are based on the CPU thermal zone for the
those boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bootloader on Odroid U2/X2/U3 boards configures main ARM clock to
1GHz. During the system shutdown procedure Linux kernel selects so called
'suspend-opp' for the CPU cores, what means that ARM clock is set to
800MHz and the CPU supply voltage is adjusted to that value. PMIC
configuration is preserved during the board reboot. Later when the
bootloader tries to enter the 1GHz mode, the voltage value configured by
the kernel might be not high enough for the CPU to operate stable. This
depends on the individual physical properties of each SoC (usually it is
related to the production series) and varies between the boards.
Typically most of the Odroid U3 boards work fine, while most of the U2
and X2 hangs during the reboot.
This commit switches suspend-opp to 1GHz for the Odroid U2/X2/U3 boards,
what finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change stmfx node name to fit with yaml requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Change stmfx node name to fit with yaml requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
resets property is well-managed in DMA drivers. In previous products,
there were no reset lines, that's why they are missing here in dma1, dma2,
dmamux and mdma nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Now that st,stm32mp15-hsotg is used, dual role is supported. ID pin is
managed to detect the current role.
On stm32mp157c-ev1, Host mode requires a vbus-supply property. Charge pump
for vbus is provided by PMIC VBUS_OTG.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add pinctrl definition for USB High-Speed OTG ID pin and USB Full-Speed OTG
DP and DM lines that can be used on stm32mp15.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Using the st,stm32mp15-hsotg compatible allows to use USB OTG with Dual Role
mode support.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Theses 3 properties are not coded in driver so remove them from the DTS.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP157C and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add missing 'eth-ck' clock to the ethernet node on stm32mp1. These
clock are used to generate external clock signal for the PHY in case
'st,eth_ref_clk_sel' is specified.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Christophe ROULLIER <christophe.roullier@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
