Active discharge is not needed on vbus_otg and generate unneeded current
consumption.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Minimal value is the value set during boot or before suspend.
We must ensure that the value is a functional value to boot.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of STM32 PWR regulators on
stm32mp157c. This replace dummy fixed regulators on
stm32mp157c-ed1 and stm32mp157c-dk2.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DSI driver doesn't use interrupt, remove it from the node since it
breaks yaml check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c-ed1 board has digital-to-analog converter signals routed
to JP11 and JP10 jumpers (e.g. PA4/PA5).
It's easier then to configure them both. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used by digital-to-analog converter on
stm32mp157c eval daughter board:
- PA4 and PA5 pins are available respectively on JP11 and JP10
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"phy-names" entries are not used. To be compliant with DT validation
tool, those entries have to be remove.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"#size-cells" entry is not needed for "gpio-keys" driver. Indeed "reg"
entry is not used. This commit will fix a warnings seen by DT validation
tool.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DT validation ("make dtbs_check") has shown that some memory nodes were not
correctly written. This commit fixes this kind of issue:
"stm32f746-disco.dt.yaml: /: memory: False schema does not allow
{'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}"
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure ADC support on stm32mp157a-dk1. It can be used for various
purpose:
- AIN connector has several analog inputs: ANA0, ANA1, ADC2 in6 & in2,
ADC1 in13 & in6
- USB Type-C CC1 & CC2 pins wired to in18 & in19
It's easier then to Configure them all. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Add VDD and VDDA supplies to ADC on stm32mp157c-dk1 board. This allows to
get full ADC analog performances in case VDDA is below 2.7V (not the case
by default).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used for ADC on stm32mp157a-dk1 board:
- AIN connector has ADC input pins
- USB Type-C CC1 & CC2 pins (e.g. in18, in19)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The ltdc pinctrl must be in the display controller node and
not in the peripheral node (hdmi bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.
Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device node name should reflect generic class of a device so rename
the "iram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
-----BEGIN PGP SIGNATURE-----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=FUNk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
-----BEGIN PGP SIGNATURE-----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=Gllx
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.5
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
* tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: add DTS for NetCom Plus 4xx and 8xx device series
ARM: dts: add DTS for NetCom Plus 1xx and 2xx device series
ARM: dts: add DTS for NetCAN Plus devices
ARM: dts: omap: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo-37xx-devkit: Increase camera pixel clock
ARM: dts: am: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo: Disable Bluetooth Serial DMA
ARM: dts: IGEP: Add WiLink UART node
ARM: dts: LogicPD Torpedo: Add WiLink UART node
ARM: dts: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel
ARM: dts: logicpd-torpedo-baseboard: Reduce video regulator chatter
ARM: dts: Add minimal support for Droid Bionic xt875
ARM: dts: omap4-droid4: Allow 300mA current for USB peripherals
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
-----BEGIN PGP SIGNATURE-----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=CWof
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
* tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: add label to sp805 watchdog
ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
arm64: dts: broadcom: Add reference to RPi 4 B
ARM: dts: Add minimal Raspberry Pi 4 support
dt-bindings: arm: bcm2835: Add Raspberry Pi 4 to DT schema
dt-bindings: arm: Convert BCM2835 board/soc bindings to json-schema
ARM: dts: bcm283x: Move BCM2835/6/7 specific to bcm2835-common.dtsi
ARM: dts: bcm283x: Remove brcm,bcm2835-pl011 compatible
ARM: dts: bcm283x: Remove simple-bus from fixed clocks
Link: https://lore.kernel.org/r/20191023212814.30622-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows boards the option of adding properties or disabling the
watchdog entirely.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This DTS file covers all four and eight port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers all one and two port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers both NetCAN Plus 110 and 120 WLAN models.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXa/4RQAKCRDj7w1vZxhR
xU3XAQDYuCixpCCftKIhjcz+oultXqAJysDEE44dATwT1YfINgD/eBSwBw1l/Ni7
yOumUvRZ1fJC3NO8e7vh9cYN9yy5tgw=
=3/ru
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe musb with ti-sysc interconnect driver and dts data
with the following changes:
1. Swap the old ti,am33xx-usb compatible wrapper to generic ti-sysc
driver. This means later on we can also remove the old wrapper driver
drivers/usb/musb/musb_am335x.c
2. Update the child nodes to use the ranges provided by ti-sysc
3. Drop unneeded status = "enabled" tinkering for SoC internal devices.
This allows us to remove some useless board specific boilerplate code
in the following patches
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is a Dell Wyse thin client, variously referred to as "Ariel",
"3020" or "Tx0D" where "x" stands for the software it was shipped with.
I somewhat arbitrarily chose "ariel".
There are bits missing, because the drivers are not in and bindings are not
settled yet:
* Things missing from mmp3.dtsi:
HSIC controller and its PHY (only the internal Ethernet is connected
here, the hub with external USB2 ports is connected to the U2O controller
that works well), Vivante GC2000 GPU
* &twsi1/regulator@19
Marvell 88pm867 power regulator
* &twsi3/vga-dvi-encoder@76
Chrontel CH7033B-BF VGA & DVI encoder
* &twsi3/sound-codec@30
Sound chip, probably a Marvell 88ce156
* &twsi4/embedded-controller@58
ENE KB3930QF Embedded Controller, also seems to be connected to &ssp4.
Might not need a driver -- about the only useful thing it can do is to
reboot the machine when tickled via some GPIO lines.
Also there seems to be something at &twsi1 address 0x50.
Link: https://lore.kernel.org/r/20191022152837.3553524-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
The device node name should reflect generic class of a device so rename
the "ocmcram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default settings used on the baseboard are good for the
OMAP3530 and are compatible with the DM3730. However, the
DM3730 has a faster L3 clock which means the camera pixel clock
can also be pushed faster as well.
This patch increase the Pixel clock to 90MHz which is the
maximum the current ISP driver permits for an L3 clock
of 200MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device node name should reflect generic class of a device so rename
the "ocmcram" node and its children to "sram". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default serial driver for omap2plus is the 8250_omap driver.
Unfortunately, this driver does not yet appear to have fully
functional DMA on OMAP3630/DM3730 which causes some timeouts and
frame errors.
This patch removes the DMA entry from the device tree which allow
the UART to operate without Bluetooth frame errors. If/when DMA
is working on OMAP3630, this should be reverted.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for the UART part of WiLink chip.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for the UART part of WiLink chip.
This is compile tested only!
Cc: Adam Ford <aford173@gmail.com>
Acked-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This tag includes binding documentation for various hardware found on Marvell
MMP3 SoC along a DTS file for said hardware.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEENyn6vISEy07peidTpxZjkszkJRYFAl2oekwPHGxrdW5kcmFr
QHYzLnNrAAoJEKcWY5LM5CUWLjgH/3u758cDz/ad1gdtTN/oIQtrHHwR2AmgCG5M
tO0+EYAPOsRAUDpPZF/aoFXoP3NJ2dUgHcj+hYX5S0ZuE4ijOJwSKiYZbXd9QX0+
e4iUh77CdtoTv+y6W6GjkFMnnjIfiCSm+Tby4jc9Ty/+ImBGGYSnS2fnxmyFfEBZ
eDtPZSGJJmmTJNt9UMaWaRC0sivSStzBPiwqVE/aG75askc/Fd3OOIcA9Bm8ot1E
i3T7i/PRw4q/mOgrXMvqs7BSTsgVnBOCxTClKIT6PuT9ZxkRUwWp9QTvEd/nVLs9
DrROFCaVKLXx7HHi+5CbjP88F0w61CBQXntFGMGkxx0iG6Evo8U=
=l10O
-----END PGP SIGNATURE-----
Merge tag 'mmp-dt-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp into arm/dt
ARM: Marvell MMP Device Tree patches for v5.5
This tag includes binding documentation for various hardware found on Marvell
MMP3 SoC along a DTS file for said hardware.
* tag 'mmp-dt-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp:
ARM: dts: mmp3: Add MMP3 SoC dts file
dt-bindings: phy-mmp3-usb: Add bindings
dt-bindings: mrvl,intc: Add a MMP3 interrupt controller
dt-bindings: arm: mrvl: Document MMP3 compatible string
dt-bindings: arm: Convert Marvell MMP board/soc bindings to json-schema
dt-bindings: arm: cpu: Add Marvell MMP3 SMP enable method
Link: https://lore.kernel.org/r/d4897c4a92319527c46147244282803cd9f5a1ff.camel@v3.sk
Signed-off-by: Olof Johansson <olof@lixom.net>
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
-----BEGIN PGP SIGNATURE-----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=uqu5
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS changes for DMC driver for v5.5
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
* tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: memory-controllers: exynos5422-dmc: Correct example syntax and memory region
ARM: dts: exynos: Add interrupts to DMC controller in Exynos5422
ARM: dts: exynos: Extend mapped region for DMC on Exynos5422
dt-bindings: memory-controllers: exynos5422-dmc: Add interrupt mode
dt-bindings: ddr: Add bindings for Samsung LPDDR3 memories
ARM: dts: exynos: Add DMC device to Exynos5422 and Odroid XU3-family boards
ARM: dts: exynos: Add syscon compatible to clock controller on Exynos542x
dt-bindings: memory-controllers: Add Exynos5422 DMC device description
dt-bindings: ddr: Add bindings for LPDDR3 memories
dt-bindings: ddr: Rename lpddr2 directory
Link: https://lore.kernel.org/r/20191021180453.29455-6-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add ARM architected timers on Exynos5 for KVM-based virtualization,
2. Extend chip identification needed for future Adaptive Supply Voltage,
3. Add audio support to Arndale board,
4. Fix init order of clock providers on s3c64xx,
5. A lot of cleanups and adjustments of DTS with DT schema.
-----BEGIN PGP SIGNATURE-----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=Ri1S
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.5
1. Add ARM architected timers on Exynos5 for KVM-based virtualization,
2. Extend chip identification needed for future Adaptive Supply Voltage,
3. Add audio support to Arndale board,
4. Fix init order of clock providers on s3c64xx,
5. A lot of cleanups and adjustments of DTS with DT schema.
* tag 'samsung-dt-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Fix init order of clock providers
ARM: dts: exynos: Rename SysRAM node to "sram"
ARM: dts: exynos: Rename power domain nodes to "power-domain" in Exynos4
ARM: dts: exynos: Add audio support (WM1811 CODEC boards) to Arndale board
ARM: dts: exynos: Use defines for MCT interrupt GIC SPI/PPI specifier
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos54xx
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos5250
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4412
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4210
ARM: dts: exynos: Rename Multi Core Timer node to "timer"
ARM: dts: exynos: Split phandle in dmas property
ARM: dts: exynos: Remove obsolete IRQ lines on Exynos3250
ARM: dts: exynos: Add samsung,asv-bin property to Odroid XU3 Lite
ARM: dts: exynos: Add "syscon" compatible string to chipid node on Exynos5
ARM: dts: exynos: Add support ARM architected timers on Exynos5
Link: https://lore.kernel.org/r/20191021180453.29455-4-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
the cpuid found in the efuses. Veyron display got a cleanup to use the
interpolated backlight values instead of declaring huge tables
and finally a cleanup fixing some tabs/spaces issues in the dts files.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl2tnOcQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgW+GCACYHiRGotnJibFu4gCerBoISP13qzqQnpYR
VSYnR84pD/cOzDas8PKOkPUg9+Db5fsDN1NPAp/S0vyirye5jgjQFlWNK7+o04Qr
JnLJYv1OlhkRiipuTJesiMo4mIOpiJWvliU050pmfzTJihZwBocw9FUqllq/V14A
WwNhcGIhZxEB+GkKkpFj7PZXSkTQy3PwmWZEAL2C9U2qHL4Vszlmo1P0AAx9af0S
8FCY1OhVSZ/C732k/aijmg7tm70uBwKeBz1Kn/Rh/AiI34yzUufxnPojQstlLkRt
pJnTypt0nc/1Gxt16So/4HjTfuIdT2pK6Q9t71VNbQl/3ogKE2Oj
=r5X+
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New rk3288 features are Gamma support for the VOPs as well as declaring
the cpuid found in the efuses. Veyron display got a cleanup to use the
interpolated backlight values instead of declaring huge tables
and finally a cleanup fixing some tabs/spaces issues in the dts files.
* tag 'v5.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove some tabs and spaces from dtsi files
ARM: dts: rockchip: Add RK3288 VOP gamma LUT address
ARM: dts: rockchip: Use interpolated brightness tables for veyron
ARM: dts: rockchip: Add cpu id to rk3288 efuse node
Link: https://lore.kernel.org/r/1770986.Em1ahGqaF7@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
-----BEGIN PGP SIGNATURE-----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=BwM0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
* tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
Link: https://lore.kernel.org/r/20191021194302.21024-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Ankur Tyagi <ankur.tyagi@gallagher.com>
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
5.4, please pull the following:
- Stefan fixes the MMC controller bus-width property for the Raspberry Pi
Zero Wireless which was incorrect after a prior refactoring
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAl2mAAYACgkQh9CWnEQH
BwTtMBAAirSdBhwX2Eclet6FImBGncD8hRMgR9L7w0uD9bPKFHf0v+w3XSdo99w3
kPnkpmKE55mgZUJSRcv/nKnS7cY4+T7myz0+Zh3066aMU8WqhYk2iWvfYGnkJUEV
R42NTJqyJ2C6P7/QVRgmZtNBvnGOt12Bm2zE/W1iyT1503BkqVVlRJ8f0Tlx282a
yRIHD4xajnmoJjyBnv+EFplaDdTZuM6+HiV/tc089zaJdVlSuPXbV24aY8NfO9tF
nZVRa/cNpS3V2QYqCOEfci3m3u5mJB2jjAPHMTaHCRhcbEefxt3i0YXRC0cnKhHp
GLg3W/vkcpx0LkwJxHy15yRhP/E1xo1IOKDY4/a0Hts/U+gkeUOdcbryuDlGO44M
8njBlHwn8hLF8h4OvEIY2bfKA8KfUpjJX2NqwxlIoaxR0rPqftdnvuBflEXQZXRL
1Bz9FOQWJ3eMBsJtvHbIPDXh/WS0MHd9So9UxP5Q2GH2zr8JIM0MTc92HPwYcknt
epFv6EQ8cmQ3xWYDjYW5WRCRwc7FaEbN++Z9s1ekzN70pHDZU3biQPmQFMrQ9M1b
bFbEJX117ZeoKFKaB4Br9GM6nR1NWj4RCIrZr/qOGQi1iHk7O5ThUVLKYM3KCp+g
HR9eVaCZ0OYFaXaPpdHikfVWCxIDch1m4mRcXTpO6exjPC/kNA8=
=z7qo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.4, please pull the following:
- Stefan fixes the MMC controller bus-width property for the Raspberry Pi
Zero Wireless which was incorrect after a prior refactoring
* tag 'arm-soc/for-5.4/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
Link: https://lore.kernel.org/r/20191015172356.9650-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdqHcmAAoJEFBXWFqHsHzOIqAIAJXqhCpbQkP5orCfXdFQxlvb
KpBiK0VEatMwPYAEm19Ij7/raFv+lRGIDo9ZyD9YGyDDIvOvRrSyeqDJCJSTEkol
QwTYl0KSNp2I4D7a0urcO4xMvcJt2QD2k3oe1Pe5mMDn5jbiMHAguUqrH96j/7zv
/9BE4n8aL9YBk6RE86YX0WMoDSfxToVQO+RQJ+7Yg66M83/9oUY3XqGv3svvZMD2
jsYtuHw8ounthr1OJSqcjUPTPLOCoEF+cG9HSkNmMCcShKNZ2wXIzvjeuBOdblKZ
MXnImEse4p7+81rsarGZLfj10tsfam4OibsgFqDIkgsT/aOdsOvXpjfp4/aO46Y=
=DFFA
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
-----BEGIN PGP SIGNATURE-----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=n/vc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With the removal of the panel-dpi from the omap drivers, the
LCD no longer works. This patch points the device tree to
a newly created panel named "logicpd,type28"
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dss driver wants two regulators or it dump some splat while
initializing. This patch adds a reference to the second regulator
which to avoid the warnings that the regulator is missing.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The node name in a device tree is supposed to be the class of the device,
not its model (even if it's a pretty generic one).
This was reported by the DT validation tools.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
bcm2835-rpi.dtsi defines the behavior of the ACT LED, which is available
on all Raspberry Pi boards. But there is no driver for this particual
GPIO on CM3 in mainline yet, so this node was left incomplete without
the actual GPIO definition. Since commit 025bf37725 ("gpio: Fix return
value mismatch of function gpiod_get_from_of_node()") this causing probe
issues of the leds-gpio driver for users of the CM3 dtsi file.
leds-gpio: probe of leds failed with error -2
Until we have the necessary GPIO driver hide the ACT node for CM3
to avoid this.
Reported-by: Fredrik Yhlen <fredrik.yhlen@endian.se>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Fixes: a54fe8a6cf ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Describes most of the hardware found on Marvell MMP3, aka PXA2128, aka
Armada 620. Missing bits are the LCD controller, HSIC controllers,
Audio and GPU. Will be completed once bindings and drivers settle.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Add a common DT include file for the Kizbox3 boards.
Add the devicetree for the Kizbox3 HS board.
Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com>
Signed-off-by: Mickael GARDET <m.gardet@overkiz.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20191011125022.16329-4-kamel.bouhara@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
* Removes mediatek,physpeed property from dtsi that is useless in PHYLINK
* Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
* Set gmac1 to gmii mode that connect to a internal gphy
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a simple network device based on BCM47094 with just a single
Ethernet port.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The commit e7774049ff ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff ("ARM: dts: bcm283x: Define MMC interfaces at board level")
Reported-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"internal_j8" and "internal_j9" are network interfaces that are not
exposed outside the board and were only ever used for debugging purposes.
Get rid of them as they are not needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the
board, since both are connected to the same parent bus and all of
their children have the same I2C address.
Fixes: ca4b4d373f ("ARM: dts: vf610: Add ZII SCU4 AIB board")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Jeff White <jeff.white@zii.aero>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RK3288 SoC VOPs have optional support Gamma LUT setting,
which requires specifying the Gamma LUT address in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191010194351.17940-4-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for years
as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXaH78w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk7mACgygFyLQ6GRUTTnGDcohZu44cuMO4AnR/MTrRq
/jiXPRUMsltMV7DHcq+S
=QX4p
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
Use interpolated brightness tables (added by commit 573fe6d1c2
("backlight: pwm_bl: Linear interpolation between
brightness-levels") for veyron, instead of specifying every single
step. Some devices/panels have intervals that are smaller than
the specified 'num-interpolated-steps', the driver interprets
these intervals as a single step.
Another option would be to switch to a perceptual brightness curve
(CIE 1931), with the caveat that it would change the behavior of
the backlight. Also the concept of a minimum brightness level is
currently not supported for CIE 1931 curves.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191003094137.v2.1.Ic9fd698810ea569c465350154da40b85d24f805b@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds minimal support for the new Raspberry Pi 4 without the
fancy stuff like GENET, PCIe, xHCI, 40 bit DMA and V3D. The RPi 4 is
available in 3 different variants (1, 2 and 4 GB RAM), so leave the memory
size to zero and let the bootloader take care of it. The DWC2 is still
usable as peripheral via the USB-C port.
Other differences to the Raspberry Pi 3:
- additional GIC 400 Interrupt controller
- new thermal IP and HWRNG
- additional MMC interface (emmc2)
- additional UART, I2C, SPI and PWM interfaces
- clock stretching bug in I2C IP has been fixed
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Florian Fanelli <f.fainelli@gmail.com>
As preparation we want all common BCM2711 + BCM2835/6/7 functions in
bcm283x.dtsi and all BCM2835/6/7 specific in the new
bcm2835-common.dtsi. Since i2c2 is BCM2835 specific, we also need
to move it to bcm2835-common.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
The fixed clocks doesn't form some kind of bus. So let's remove it.
This fixes the follow DT schema warnings:
clocks: clock@3:reg:0: [3] is too short
clocks: clock@4:reg:0: [4] is too short
clocks: $nodename:0: 'clocks' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
clocks: #size-cells:0:0: 0 is not one of [1, 2]
clocks: 'ranges' is a required property
clock@3: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
clock@4: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Add PRM data for OMAP54xx SoC. Initially this is used to provide reset
support, but will be expanded later to support also powerdomain control.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PRM data for AM43xx SoC. Initially this is used to provide reset
support, but will be expanded later to support also powerdomain control.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PRM data for AM33xx SoC. Initially this is used to provide reset
support, but will be expanded later to support also powerdomain control.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PRM nodes for omap4 series of SoCs. These are initially used to
support reset control for some of the nodes, but will be extended
later to add powerdomain control and support for PRCM irqs among
other things.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PRM nodes for dra7 series of SoCs. These are initially used to
support reset control for some of the nodes, but will be extended
later to add powerdomain control and support for PRCM irqs among
other things.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517 only lists 600MHz @ 1.2V, but the register values for
0x4830A204 = 1b86 802f, it seems like am3517 might be a derivative
of the omap36 which OPPs would be OPP50 (300 MHz) and OPP100
(600 MHz).
This patch sets up the OPP50 and OPP100 tables at 300MHz and 600MHz
for the AM3517 with each having an operating voltage at 1.2V.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
See DM3730,DM275 data sheet (SPRS685B) footnote (6) in Table 4-19
which says that ABB must be switched to FBB mode when using the
OPP1G.
The LOD definition abb_mpu_iva already exists so that we need
to add plumbing for vbb-supply = <&abb_mpu_iva>
and define two voltage vectors for each OPP so that the abb LDO
is also updated by the ti-cpufreq driver.
We also must switch the ti_cpufreq_soc_data to multi_regulator.
Note: reading out the abb reglator voltage to verify that
it does do transitions can be done by
cat /sys/devices/platform/68000000.ocp/483072f0.regulator-abb-mpu/regulator/regulator.*/microvolts
Likewise, read the twl4030 provided VDD voltage by
cat /sys/devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:regulator-vdd1/regulator/regulator.*/microvolts
Note: to check if the ABB FBB is enabled/disabled, check
registers
PRM_LDO_ABB_CTRL 0x483072F4 bit 3:0 1=bypass 5=FBB
PRM_LDO_ABB_SETUP 0x483072F0 0x00=bypass 0x11=FBB
e.g.
/dev/mem opened.
Memory mapped at address 0xb6fe4000.
Value at address 0x483072F4 (0xb6fe42f4): 0x3205
/dev/mem opened.
Memory mapped at address 0xb6f89000.
Value at address 0x483072F4 (0xb6f892f4): 0x3201
Note: omap34xx and am3517 have/need no comparable LDO
or mechanism.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
For the ti-cpufreq driver we need a clear separation between omap34 and omap36 families
since they have different silicon revisions and efuses.
So far ti,omap3630/ti,omap36xx is just an additional flag to ti,omap3 while omap34 has no
required entry.
Therefore we can not match omap34 boards properly.
This needs to add ti,omap3430 and ti,omap3630 where it is missing.
We also clean up some instances of missing ti,am3517 so that we can rely on
seeing either one of:
ti,am3517
ti,omap3430
ti,omap3630
in addition to ti,omap3.
We leave ti,omap34xx and ti,omap36xx untouched for compatibility.
The script to do the conversion is:
manually fix am3517_mt_ventoux.dts
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap34xx"/"ti,omap3430", "ti,omap34xx"/' {} \;
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; -exec sed -i '' 's/"ti,omap36xx"/"ti,omap3630", "ti,omap36xx"/' {} \;
find arch/arm/boot/dts \( -name 'omap*.dts*' -o -name 'logic*.dts*' \) -exec fgrep -q '"ti,omap3"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; ! -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,am3517"' {} \; ! -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap3"/"ti,omap3430", "ti,omap3"/' {} \;
So if your out-of-tree omap3 board does not show any OPPs, please check
the compatibility entry and update if needed.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
With the driver installed, we can change the opp-v1 table format
to opp-v2.
In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev
in the same patch, because doing either first breaks operation and
may make trouble in bisect.
We also can remove opp-v1 table for omap3-n950-n9 since its 1GHz
capability is now automatically detected.
We also fix a wrong OPP4 voltage for omap3430 which must be
0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject
this OPP.
Note: the high speed OPPs that were not available in the opp-v1 tables
are tagged "turbo-mode;" which means they are not automatically
activated by the govenors or cpu-freq.
To enable you have to write
echo 1 >/sys/devices/system/cpu/cpufreq/boost
Note: to hard disable an OPP in a board.dts file use e.g.
&cpu0_opp_table: {
/delete-node/ opp1g-1000000000; /* do not use */
};
or alternatively:
&cpu0_opp_table: {
opp1g-1000000000 {
status = "disabled"; /* do not use */
};
};
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We already have folks booting Droid Bionic with Droid 4 dts, but it is
a different hardware with no keyboard.
Let's start adding device specific support for Droid bionic by making
current omap4-droid4-xt894 a common file and including it.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we can use some USB Ethernet dongles for example if we increase
the allowed power limit.
A similar PMIC MC13783 documents maximum current limit as 300 mA in in
"Table 10-4. VBUS Regulator Main Characteristics". Since we have no
other documentation, let's use that value as the limit.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 572cf7d7b0 ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b0 ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt,
i2c-mux-idle-disconnect is a property of a parent node since it
pertains to the mux/switch as a whole, so move it there and drop all
of the concurrences in child nodes.
Fixes: d031773169 ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07 ("ARM: dts: Configure sgx for omap5")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the label "sdramc" to the sdram-controller nodes for the Armada-XP
and 98dx3236 SoCs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Armada-38x uses an SDRAM controller that is compatible with the
Armada-XP. The key difference is the width of the bus (XP is 64/32, 38x
is 32/16). The SDRAM controller registers are the same between the two
SoCs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable L2 cache parity and ECC on the db-xc3-24g4xg board so that cache
operations are protected and errors can be flagged to the EDAC
subsystem.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The device node name should reflect generic class of a device so rename
the "sa-sram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In the rtc-rs5c372.c driver the compatible entry has been renamed
from rs5c372 to rs5c372a. Most dts files have been adapted.
This patch completes the change.
Signed-off-by: Walter Schweizer <ws.kernel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
KeyStone 66AK2L 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSREFCLK clocks as CPTS
reference clock [1] and group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2l06
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
KeyStone 66AK2H/K 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSREFCLK clocks as CPTS reference clock [1] and
group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2h14
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
KeyStone 66AK2E 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSIPCLKA, TSREFCLK, TSIPCLKB clocks as CPTS
reference clock [1] and group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2e05
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add set of fixed, external input clocks definitions for TSIPCLKA, TSIPCLKB
clocks. Such clocks can be used as reference clocks for some HW modules (as
cpts, for example) by configuring corresponding clock muxes. For these
clocks real frequencies have to be defined in board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add set of fixed, external input clocks definitions for TIMI0, TIMI1,
TSREFCLK clocks. Such clocks can be used as reference clocks for some HW
modules (as cpts, for example) by configuring corresponding clock muxes.
For these clocks real frequencies have to be defined in board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Fixes: d2b9c64443 ("ARM: dts: sun7i: Add CSI0 controller")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Move the CAN enablement from SoM DTSi to board DTS, as each board might need
different CAN configuration. Moreover, disable CAN2 on the PDK2 as it is not
available on any connector. This also fixes on-SoM SD slot operation, as it
shares pins with the CAN2.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pm8941 is missing the 5vs2 regulator node so let's add it since its
needed to get the external display working. This regulator was already
configured in the interrupts property on the parent node.
Note that this regulator is referred to as mvs2 in the downstream MSM
kernel sources.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The device node name should reflect generic class of a device so rename
the SysRAM node from "sysram" to "sram". The child nodes stay as before
as "smp-sysram" to match their real purpose. This will be also in sync
with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The device node name should reflect generic class of a device so rename
power domain nodes to "power-domain". No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add "opp-suspend" property for i.MX7D to make sure system
suspend with max available opp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 800MHz opp speed grading fuse mask should be 0xd instead
of 0xf according to fuse map definition:
SPEED_GRADING[1:0] MHz
00 800
01 500
10 1000
11 1200
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6qdl-gw551x.dtsi:109.32-121.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following build warning
with W=1:
arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi:23.9-26.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Cc: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace "simple-bus" with "simple-mfd" for anatop node in order
to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6sx.dtsi:603.31-616.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-1p1: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:618.31-631.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-3p0: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:633.31-646.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-2p5: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:648.32-663.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:665.33-679.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpcie: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:681.31-696.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc: missing or empty reg/ranges property
Based on a patch from Marco Felsch for the imx6qdl.dtsi.
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables userspace to signal the bootloader to go into the
bootloader or recovery mode.
The magic values can be found in both the downstream kernel and the LK
kernel (bootloader).
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Before this change, trying to boot from the internal storage would
result in a lot of errors like:
[ 11.224046] mmc0: cache flush error -110
[ 11.224180] blk_update_request: I/O error, dev mmcblk0, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 0 prio class 0
or:
[ 137.544673] mmc0: tuning execution failed: -5
[ 137.569832] mmcblk0: error -110 requesting status
[ 137.593558] mmcblk0: recovery failed!
With this patch, there are no more sdhci errors and booting works fine.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The gpio is not used for SD card detection on the FP2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mmc capabilities for SDMMC0 for this board.
With this enabled, eMMC connected card is detected as:
mmc0: new DDR MMC card at address 0001
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/1565252928-28994-2-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
-----BEGIN PGP SIGNATURE-----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=SkMF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Add interrupts to Dynamic Memory Controller in Exynos5422 and Odroid
XU3-family boards. It will be used instead of devfreq polling mode
governor. The interrupt is connected to performance counters private
for DMC, which might track utilisation of the memory channels.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DMC Adaptive Voltage and Frequency Scaling driver in interrupt mode
needs to access registers at address offset near 0x10000. These
registers are private DMC performance counters, which might be used
as interrupt trigger when overflow. Potential usage is to skip polling
in devfreq framework and switch to interrupt managed bandwidth control.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add sound node and the clock configurations for the I2S controller
for audio support on the Exynos5250 SoC Arndale boards with
WM1811 based audio daughter board.
We need to increase drive strength of the I2S bus, otherwise
the audio CODEC doesn't work. Likely the CODEC's master clock
is the main issue here.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded number with appropriate define for GIC SPI or PPI
specifier in interrupt. This makes code easier to read. No expected
functionality change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Tested on Odroid XU (Exynos5410), Odroid HC1 (Exynos5422) and Arndale
Octa (Exynos5420).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Tested on Odroid U3 (Exynos4412).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Multi Core Timer node has interrupts routed to two different parents -
GIC and combiner. This was modeled with a interrupt-map within a
subnode but can be expressed in an easier and more common way, directly
in the node itself.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The device node name should reflect generic class of a device so rename
the Multi Core Timer node from "mct" to "timer". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change representation of phandle array as then dt-schema counts number
of its items properly.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In commit 7222e8db2d ("iommu/exynos: Fix build errors") Exynos3250
IOMMU driver stopped supporting two IRQ lines. The second IRQ line in
DTS is ignored and is not needed.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Exynos5422 SoC used on Odroid XU3 Lite boards belongs to a special
ASV bin but this information cannot be read from the Chip ID block
registers. Add samsung,asv-bin property for XU3 Lite to ensure the ASV
bin is properly determined.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Chip ID block in addition to exact chip revision information
contains data and control registers for ASV (Adaptive Supply Voltage)
and ABB (Adaptive Body Bias). Add "syscon" compatible so the Chip ID
block can be shared by respective drivers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
All CortexA7/A15 based Exynos5 SoCs have ARM architected timers, so enable
support for them directly in the base dtsi. None of the known firmware
properly configures CNTFRQ arch timer register, so force clock frequency
to 24MHz, which is the only configuration supported by the remaining
clock drivers so far.
Stock firmware for Peach Pit and Pi Chromebooks also doesn't reset
properly other arch timer registers, so add respective properties
indicating that. Other Exynos5-based boards behaves correctly in this area,
what finally allows to enable support for KVM-based virtualization.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
IPQ4019 has a built in SD/eMMC controller which is supported by the
SDHCI MSM driver, by the "qcom,sdhci-msm-v4" binding.
So lets add the appropriate node for it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds the possibility to wake the module with an external signal
as defined in the Colibri standard
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.
This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds some missing pinmuxing that is in the colibri
standard to the dts.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds the touchscreen from Toradex so one can enable it.
It is disabled by default because the pins are also used for PWM<B>,
PWM<C>, aka pwm2, pwm3 which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the muxing for the optional pins usb-oc (overcurrent) and
usb-id.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add touch controller that is connected over an I2C bus.
It is disabled by default because the pins are also used for PWM,
which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pinmuxing and do not specify voltage restrictions for the usdhc
instance available on the modules edge connector. This allows to use
SD-cards with higher transfer modes if supported by the carrier board.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add wakeup GPIO key which is able to wake the system from sleep
modes (e.g. Suspend-to-Memory).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the IMX7ULP reference manual, the mipi pll
clock comes from the MIPI PHY PLL output. So it should
not be defined as a fixed clock. So remove this clock
node and all the references to it.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rework the device trees of the OPOS6UL and OPOS6ULDev boards to support
the OPOS6UL SoM with an i.MX6ULL SoC. The device trees are now as
following:
- imx6ul-imx6ull-opos6ul.dtsi
common for both i.MX6UL and i.MX6ULL OPOS6UL SoM.
- imx6ul-opos6ul.dtsi
for i.MX6UL OPOS6UL SoM. It includes imx6ul.dtsi and
imx6ul-imx6ull-opos6ul.dtsi.
- imx6ull-opos6ul.dtsi
for i.MX6ULL OPOS6UL SoM. It includes imx6ull.dtsi and
imx6ul-imx6ull-opos6ul.dtsi.
- imx6ul-imx6ull-opos6uldev.dtsi
OPOS6ULDev base device tree.
- imx6ul-opos6uldev.dts
OPOS6ULDev board with an i.MX6UL OPOS6UL SoM. It includes
imx6ul-opos6ul.dtsi and imx6ul-imx6ull-opos6uldevdtsi.
- imx6ull-opos6uldev.dts
OPOS6ULDev board with an i.MX6ULL OPOS6UL SoM. It includes
imx6ull-opos6ul.dtsi and imx6ul-imx6ull-opos6uldevdtsi.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add description of Dynamic Memory Controller and PPMU counters to
Exynos5422 and Odroid XU3/XU4/HC1 boards. They are used by
exynos5422-dmc driver. There is a definition of the memory chip, which
is then used during calculation of timings for each OPP.
The algorithm in the driver needs these two sets to bound the timings.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to get the clock by phandle and use it with regmap it needs to be
compatible with syscon. The DMC driver uses two registers from clock
register set and needs the regmap of them.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This fixes up the default ux500 CPU thermal zone:
- Set polling delay to 0 and explain why
- Set passive polling delay to 250
- Remove restrictions from the CPU cooling device,
we should use all cpufreq steps to cool down if
needed.
Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org
Fixes: b786a05f6c ("ARM: dts: ux500: Update thermal zone")
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
It turns out that the GPIO nodes for EMEV2 are missing whitespace,
so focus on what is important in life and adjust the coding style
to match the rest of the code base.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/156877169225.29395.9771334507494949542.sendpatchset@octo
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This just adds in another field of what's stored in the e-fuse on
rk3288. Though I can't personally promise that every rk3288 out there
has the CPU ID stored in the eFuse at this location, there is some
evidence that it is correct:
- This matches what was in the Chrome OS 3.14 branch (see
EFUSE_CHIP_UID_OFFSET and EFUSE_CHIP_UID_LEN) for rk3288.
- The upstream rk3399 dts file has this same data at the same offset
and with the same length, indiciating that this is likely common for
several modern Rockchip SoCs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190919142611.1.I309434f00a2a9be71e4437991fe08abc12f06e2e@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI
-----BEGIN PGP SIGNATURE-----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=s4qF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
TRM "Table 13-34. SYSCONFIG Register Field Descriptions" lists both
standbymode and idlemode that should be just the sidle and midle
registers where midle is currently unconfigured for lcdc_sysc. As
the dts data has been generated based on lcdc_sysc, we now have an
empty "ti,sysc-midle" property.
And so we currently get a warning for lcdc because of a difference
with dts provided configuration compared to the legacy platform
data. This is because lcdc has SYSC_HAS_MIDLEMODE configured in
the platform data without configuring the modes.
Let's fix the issue by adding the missing midlemode to lcdc_sysc,
and configuring the "ti,sysc-midle" property based on the TRM
values.
Fixes: f711c575cf ("ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data")
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc")
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 6953c57ab1 "gpio: of: Handle SPI chipselect legacy bindings"
did introduce logic to centrally handle the legacy spi-cs-high property
in combination with cs-gpios. This assumes that the polarity
of the CS has to be inverted if spi-cs-high is missing, even
and especially if non-legacy GPIO_ACTIVE_HIGH is specified.
The DTS for the GTA04 was orginally introduced under the assumption
that there is no need for spi-cs-high if the gpio is defined with
proper polarity GPIO_ACTIVE_HIGH.
This was not a problem until gpiolib changed the interpretation of
GPIO_ACTIVE_HIGH and missing spi-cs-high.
The effect is that the missing spi-cs-high is now interpreted as CS being
low (despite GPIO_ACTIVE_HIGH) which turns off the SPI interface when the
panel is to be programmed by the panel driver.
Therefore, we have to add the redundant and legacy spi-cs-high property
to properly activate CS.
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ahclkr clkctrl clock bit 28 only exists for mcasp 1 and 2 on dra7.
This causes the following warning on beagle-x15:
ti-sysc 48468000.target-module: could not add child clock ahclkr: -19
Also the mcasp clkctrl clock bits are wrong:
For mcasp1 and 2 we have four clocks at bits 28, 24, 22 and 0:
bit 28 is ahclkr
bit 24 is ahclkx
bit 22 is auxclk
bit 0 is fck
For mcasp3 to 8 we have three clocks at bits 24, 22 and 0.
bit 24 is ahclkx
bit 22 is auxclk
bit 0 is fck
We do not have currently mapped auxclk at bit 22 for the drivers, that can
be added if needed.
Fixes: 5241ccbf28 ("ARM: dts: Add missing ranges for dra7 mcasp l3 ports")
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- fix various clang build and cppcheck issues
- switch ARM to use new common outgoing-CPU-notification code
- add some additional explanation about the boot code
- kbuild "make clean" fixes
- get rid of another "(____ptrval____)", this time for the VDSO code
- avoid treating cache maintenance faults as a write
- add a frame pointer unwinder implementation for clang
- add EDAC support for Aurora L2 cache
- improve robustness of adjust_lowmem_bounds() finding the bounds of
lowmem.
- add reset control for AMBA primecell devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Evmc
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- fix various clang build and cppcheck issues
- switch ARM to use new common outgoing-CPU-notification code
- add some additional explanation about the boot code
- kbuild "make clean" fixes
- get rid of another "(____ptrval____)", this time for the VDSO code
- avoid treating cache maintenance faults as a write
- add a frame pointer unwinder implementation for clang
- add EDAC support for Aurora L2 cache
- improve robustness of adjust_lowmem_bounds() finding the bounds of
lowmem.
- add reset control for AMBA primecell devices
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (24 commits)
ARM: 8906/1: drivers/amba: add reset control to amba bus probe
ARM: 8905/1: Emit __gnu_mcount_nc when using Clang 10.0.0 or newer
ARM: 8904/1: skip nomap memblocks while finding the lowmem/highmem boundary
ARM: 8903/1: ensure that usable memory in bank 0 starts from a PMD-aligned address
ARM: 8891/1: EDAC: armada_xp: Add support for more SoCs
ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC
ARM: 8892/1: EDAC: Add missing debugfs_create_x32 wrapper
ARM: 8890/1: l2x0: add marvell,ecc-enable property for aurora
ARM: 8889/1: dt-bindings: document marvell,ecc-enable binding
ARM: 8886/1: l2x0: support parity-enable/disable on aurora
ARM: 8885/1: aurora-l2: add defines for parity and ECC registers
ARM: 8887/1: aurora-l2: add prefix to MAX_RANGE_SIZE
ARM: 8902/1: l2c: move cache-aurora-l2.h to asm/hardware
ARM: 8900/1: UNWINDER_FRAME_POINTER implementation for Clang
ARM: 8898/1: mm: Don't treat faults reported from cache maintenance as writes
ARM: 8896/1: VDSO: Don't leak kernel addresses
ARM: 8895/1: visit mach-* and plat-* directories when cleaning
ARM: 8894/1: boot: Replace open-coded nop with macro
ARM: 8893/1: boot: Explain the 8 nops
ARM: 8876/1: fix O= building with CONFIG_FPE_FASTFPE
...
This is some material that we picked up into our tree late or
that had complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the most
interesting new additions:
The new Aspeed AST2600 baseboard management controller is added, this
is a Cortex-A7 based follow-up to the ARM11 based AST2500 and had some
dependencies on other device drivers.
After many years, support for the MMP2 based OLPC XO-1.75 finally makes
it into the kernel.
The Armada 3720 based Turris Mox open source router platform is a late
addition and it follows some preparatory work across multiple branches.
The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of the
now-unused platform data.
The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdf6P3AAoJEJpsee/mABjZMFUP/i/J9CNJjEec0cWCG1XgP/qh
SpKFf2g9Y9QzqAzDDovo7atTGHTCG8C0fn8W+bkv9h7dWj2uxRtFISM9COomUoHa
0qXUL9bbDB3LAvstLV451p4c67XsJUazV9KZPD7VsCquucWbDDYaGPz+0reSRm6y
imK2jXqD0leG0CNbgRXfh64J32TF3M0/XnwbsNJreCmQvwUvkYLL5VNi/qcnvfyp
k0g1/5OzH9mLertoVKWqJ9o1919Yvxdl6/eyDmTPmX08bs03WnPbCEzRVO/zkOKZ
O6RcAlsjiLblQdfbDJKfbaYDDaE53d2NwdCvBIdSPmDoYM5eYjQC4PmDM0+0dmHe
bFd9giBjzU2Uab7ylgeoVl6pX1ISk6bwmZxNup45cy0xyw8wuky02Wq2bQTuZbgI
UcBlOGWR4aH/OCpNafn+ovDBYGc64I7EQobG7UiilrVq/libx1Uo7yjlWSxe4j8n
wFchiB8It24WUiS4JhJFrTklkaf5JW3K3czdDATW7aZKjv+fnHU5GMre/hvNP4z7
qROlP69/eqNXG25VOcwWPQE8yhP43+ZgyvoVwDh1H6VZdy9WxgYyEoiBAhFfcrng
+RVAT4rzylPmKP8oygVF1fpTHTS8xHrYBbjkdRaj5KqmTDdqI/nMsYoq+E0R1ScV
EsnyNVq7wnvH12zrOv+I
=Qtkp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the staging
directory, uwb and wusb (wireless USB support), because there are no
devices that actually use this protocol anymore, and what we have today
probably doesn't work at all given that the maintainers left many many
years ago. So move it to staging where it will be removed in a few
releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups due
to the driver core changes to support that. Nothing really major, just
constant forward progress.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIYYQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymn8ACfTi8Y2ku/yqw8Nvs4vQjc08MUDhgAoNnbhsI6
H3HUrZTjJJzuxHCM22Lh
=8ZRm
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit respectively.
There are lots of cleanups and additional hardware support for platforms
we already support based on SoCs from Renesas, ST-Microelectronics,
Intel/Altera, Rockchips, Allwinner, Broadcom and other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone platform,
usually paired with an external 5G modem. So far we only support the
Qualcomm SM8150 MTP reference platform, but no actual products.
For the slightly older Qualcomm platforms, support for several interesting
products is getting added: Three laptops based on Snapdragon 835/MSM8998
(Asus NovaGo, HP Envy X2 and Lenovo Miix 630), one laptop based on
Snapdragon 850/sdm850 (Lenovo Yoga C630) and several phones based on
the older Snapdragon 410/MSM8916 (Samsung A3 and A5, Longcheer L8150
aka Android One 2nd gen "seed" aka Wileyfox Swift).
Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
Allwinner V3 is a repackaged version of the existing low-end V3s chip,
and is used in the tiny Lichee Pi Zero plus, also added here. There is
also a new TV set-top box based on Allwinner H6, the Tanix TX6, and the
eMMC variant of the Olimex A64-Olinuxino development board.
NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC family,
similar to the i.MX8M Mini. As usual, there is a large number of new
boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML, SolidRun Hummingboard
Pulse baseboard and System-on-Module, Boundary Devices i.MX8MQ Nitrogen8M,
and TechNexion PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit,
we get the Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from their
set-top-box line and smart speaker with newer CPU and GPU cores compared
to their predecessors. Both are now also supported by the Khadas VIM3
development board series, and the dts files for that get reorganized a
bit to better deal with all variants. Another board based on SM1 that
gets added is the SEI Robotics SEI610.
There are a handful of new x86 and Power9 server boards using Aspeed BMC
chips that are gaining support for running Linux on the BMC through the
OpenBMC project: Facebook Minipack/Wedge100/Wedge40, Lenovo Hr855xg2,
and Mihawk. Notably these are still new machines using SoCs based on
the ARM9 and ARM11 CPU cores, as support for the new Cortex-A7 based
AST2600 is still ramping up.
There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the low-end
RK3229 chip, while the two AOpen products Chromebox Mini (Fievel) and
Chromebase Mini (Tiger) run ChromeOS and are meant for commercial settings
(digital signage, PoS, ...).
One more single-board computer based on the popular 64-bit RK3399 is
added: the Leez RK3399 P710.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Bm5T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT updates from Arnd Bergmann:
"This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit
respectively. There are lots of cleanups and additional hardware
support for platforms we already support based on SoCs from Renesas,
ST-Microelectronics, Intel/Altera, Rockchips, Allwinner, Broadcom and
other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
- The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone
platform, usually paired with an external 5G modem. So far we only
support the Qualcomm SM8150 MTP reference platform, but no actual
products.
- For the slightly older Qualcomm platforms, support for several
interesting products is getting added: Three laptops based on
Snapdragon 835/MSM8998 (Asus NovaGo, HP Envy X2 and Lenovo Miix
630), one laptop based on Snapdragon 850/sdm850 (Lenovo Yoga C630)
and several phones based on the older Snapdragon 410/MSM8916
(Samsung A3 and A5, Longcheer L8150 aka Android One 2nd gen "seed"
aka Wileyfox Swift).
- Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
- Allwinner V3 is a repackaged version of the existing low-end V3s
chip, and is used in the tiny Lichee Pi Zero plus, also added here.
There is also a new TV set-top box based on Allwinner H6, the Tanix
TX6, and the eMMC variant of the Olimex A64-Olinuxino development
board.
- NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC
family, similar to the i.MX8M Mini. As usual, there is a large
number of new boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML,
SolidRun Hummingboard Pulse baseboard and System-on-Module,
Boundary Devices i.MX8MQ Nitrogen8M, and TechNexion
PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit, we get the
Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
- In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
- Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from
their set-top-box line and smart speaker with newer CPU and GPU
cores compared to their predecessors. Both are now also supported
by the Khadas VIM3 development board series, and the dts files for
that get reorganized a bit to better deal with all variants.
Another board based on SM1 that gets added is the SEI Robotics
SEI610.
- There are a handful of new x86 and Power9 server boards using
Aspeed BMC chips that are gaining support for running Linux on the
BMC through the OpenBMC project: Facebook
Minipack/Wedge100/Wedge40, Lenovo Hr855xg2, and Mihawk. Notably
these are still new machines using SoCs based on the ARM9 and ARM11
CPU cores, as support for the new Cortex-A7 based AST2600 is still
ramping up.
- There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the
low-end RK3229 chip, while the two AOpen products Chromebox Mini
(Fievel) and Chromebase Mini (Tiger) run ChromeOS and are meant for
commercial settings(digital signage, PoS, ...).
- One more single-board computer based on the popular 64-bit RK3399
is added: the Leez RK3399 P710"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (467 commits)
arm64: dts: qcom: Add Lenovo Yoga C630
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
ARM: dts: exynos: Enable GPU/Mali T604 on Arndale board
ARM: dts: exynos: Enable GPU/Mali T604 on Chromebook Snow
ARM: dts: exynos: Add GPU/Mali T604 node to Exynos5250
ARM: dts: exynos: Fix min/max buck4 for GPU on Arndale board
ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks
ARM: dts: exynos: Remove not accurate secondary ADC compatible
arm64: dts: rockchip: limit clock rate of MMC controllers for RK3328
arm64: dts: meson-sm1-sei610: add stdout-path property back
arm64: dts: meson-sm1-sei610: enable DVFS
arm64: dts: khadas-vim3: add support for the SM1 based VIM3L
dt-bindings: arm: amlogic: add Amlogic SM1 based Khadas VIM3L bindings
arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi
arm64: dts: meson: g12a: add reset to tdm formatters
...
The D-Link DIR-685 had its clock polarity set as active
low using the special SPI "spi-cpol" property.
This is not correct: the datasheet clearly states:
"Fix SCL to GND level when not in use" which is
indicative that this line is active high.
After a recent fix making the GPIO-based SPI driver
force the clock line de-asserted at the beginning of
each SPI transaction this reared its ugly head: now
de-asserted was taken to mean the line should be
driven high, but it should be driven low.
Fix this up in the DTS file and the display works again.
Link: https://lore.kernel.org/r/20190915135444.11066-1-linus.walleij@linaro.org
Cc: Mark Brown <broonie@kernel.org>
Fixes: 2922d1cc16 ("spi: gpio: Add SPI_MASTER_GPIO_SS flag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add them in their own dtsi and include it in aspeed-g6.dtsi to isolate
the cruft.
Link: https://lore.kernel.org/r/20190911165614.31641-2-joel@jms.id.au
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AST2600 is a new SoC by ASPEED. It contains a dual core Cortex A7
CPU and shares many periperhals with the existing AST2400 and AST2500.
Link: https://lore.kernel.org/r/20190911165614.31641-1-joel@jms.id.au
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a fairly complete description of an OLPC XO 1.75 laptop.
What's missing for now is the GPU, LCD controller, DCON, the panel and
audio.
The machine is booted with OpenFirmware and thus has a devicetree.
However, older versions are unable to create a valid FDT and don't
follow the Linux bindings. Having an device tree in the kernel tree
makes it easier to use mainline kernels on such machines, test changes
with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings
are used on the machine without an access to one.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This device is not an OTG phy, it's a regular USB HS phy. Follow the
generic node name recommendation, and rename it to "usb-phy".
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This makes the 8250_of driver happy. There are two more drivers in the
tree that bind to mrvl,mmp-uart compatibles: pxa and 8250_pxa and
neither of them requires the reg-shift property, assuming it's always 2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
The SPI bus has a single address cell and not size cells.
Also, dtc thinks the SPI nodes are preferrably called "spi" and it is
right to think so.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to stable by
me when I blindly requested the pull after seeing I2C issues without
actually reviewing the content of the pinout. Since the bootloader
previously muxed these correctly in the past, was a hidden error.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Fixes: 5fe3c0fa0d ("ARM: dts: Add pinmuxing for i2c2 and i2c3
for LogicPD SOM-LV") #4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
video on the AM3517-evm stop working because it relied on the dpi
driver for setting video timings. Now that the simple-panel driver
is available in omap2plus, this patch migrates the am3517-evm
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
Torpedo video stop working because it relied on the dpi driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the Torpedo dev kits
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
any market.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl1w+fEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgaolB/9QiQc2k2HFAwQTS1RpvVW87yKdLXPhqBBs
HhagbY3ucMXDY38tZnLnbLis6CwdvkeHCCL6KC9XLzIgiJZHzXhb+QLiu9YLAw25
ymnWVtamVh0WmSNOBqex65fXwCQH9l/godI8BaxltllEkb472/jwainqHsVkFI7Z
idVGrTo9zgW7NTGQU88Rl6cagHLR6OpHBvc5meu7TIzGYF2U+Xx+x9TZw7BfdQ7u
gKZtIeRTFwsHdiBNbeU78znQCW/apCyzyKaIKW517TiXQsmsm/CEGai2/+XTN0ft
+QqHkXO7NBUh0cPZvBefq53EyDlvJbv1TW+XXP9d+TTFotTtJmXU
=PkdV
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Removal of the rk3288-fennec board which never made it to
any market.
* tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: arm: rockchip: remove reference to fennec board
ARM: dts: rockchip: remove rk3288 fennec board support
Link: https://lore.kernel.org/r/1718334.9BoTfW0Ujv@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Alternate flash support for Vesnin
- Minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=ranz
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.4-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.4, second round
- Alternate flash support for Vesnin
- Minor cleanups and fixes
* tag 'aspeed-5.4-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
Link: https://lore.kernel.org/r/CACPK8Xdp4gVuetmiu2bRTTH6oHhRrC7FELHWKVB2ZGSbPbH7HQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to the AST2500/AST2520 specs, these SoCs support up to 228 GPIO
pins. However, 'gpio-ranges' value in 'aspeed-g5.dtsi' file is currently
setting the upper limit to 220 which isn't allowing access to all their
GPIOs. The correct upper limit value is 232 (actual number is 228 plus a
4-GPIO hole in GPIOAB). Without this patch, GPIOs AC5 and AC6 do not work
correctly on a AST2500 BMC running Linux Kernel v4.19
Fixes: 2039f90d13 ("ARM: dts: aspeed-g5: Add gpio controller to devicetree")
Signed-off-by: Oscar A Perez <linux@neuralgames.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Swift power supplies are version 2 of the IBM CFFPS.
Fixes: 8e8fd0cbd7 ("ARM: dts: aspeed: Add Swift BMC machine")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adds wdt2 section with 'alt-boot' option into dts for vesnin.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The FMC supports five chip selects, so describe the five possible flash
chips.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested with kmscube and some glmark2* tests on arndale board.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested with kmscube and some glmark2* tests on Chromebook snow.
Frequency adapts with load.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Required to have GPU voltage scaling working properly.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
-----BEGIN PGP SIGNATURE-----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=a2cp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
SoC glue layer changes for SGX on omap variants for v5.4
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
* tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: ARM: dts: Configure interconnect target module for am3517sgx
ARM: dts: Configure interconnect target module for omap3 sgx
ARM: dts: Configure sgx for omap5
clk: ti: add clkctrl data omap5 sgx
ARM: OMAP2+: Drop legacy platform data for omap4 gpu
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
-----BEGIN PGP SIGNATURE-----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=mBPp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop legacy platform data omap variants for v5.4
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
* tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Drop legacy custom hwmods property for dra7 gpio
ARM: dts: Drop legacy custom hwmods property for dra7 mmc
ARM: dts: Drop legacy custom hwmods property for dra7 i2c
ARM: dts: Drop legacy custom hwmods property for dra7 uart
ARM: OMAP2+: Drop legacy platform data for dra7 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 mcspi
ARM: OMAP2+: Drop legacy platform data for omap4 d2d
ARM: dts: Configure d2d dts data for omap4
ARM: OMAP2+: Drop legacy watchdog platform data for omap4
ARM: dts: Drop custom hwmod property for omap4 i2c
ARM: OMAP2+: Drop legacy platform data for cpsw on dra7
ARM: OMAP2+: Drop legacy platform data for cpsw on am3 and am4
ARM: dts: Add fck for cpsw mdio for omap variants
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.4, please pull the following:
- Stefan does a bunch of preparatory work for supporting the Raspberry
Pi 4in the next merge window correct register ranges (SPI, I2C,
UART), define memory, HDMI and MMC properties at the board level
-----BEGIN PGP SIGNATURE-----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=DR09
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.4, please pull the following:
- Stefan does a bunch of preparatory work for supporting the Raspberry
Pi 4in the next merge window correct register ranges (SPI, I2C,
UART), define memory, HDMI and MMC properties at the board level
* tag 'arm-soc/for-5.4/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Enable HDMI at board level
ARM: dts: bcm283x: Define memory at board level
ARM: dts: bcm283x: Define MMC interfaces at board level
ARM: bcm283x: Reduce register ranges for UART, SPI and I2C
This helps SPI NOR to work on newer board variants.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZBa8
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.4/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/dt
Contains a patch to switch to more generic compatible for SPI NOR.
This helps SPI NOR to work on newer board variants.
* tag 'davinci-for-v5.4/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: Use generic jedec, spi-nor for flash
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Drop TV-OUT muxgroup from the HREF pin control
- Fix up BU21013 touchpad from Dmitry
- Split of AB8500 config in its own DTSI
- Drop the unused USB regulator config
- Add proper thermal zone for the CPU
-----BEGIN PGP SIGNATURE-----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=JGg5
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
More Ux500 device tree updates for the v5.4 kernel:
- Drop TV-OUT muxgroup from the HREF pin control
- Fix up BU21013 touchpad from Dmitry
- Split of AB8500 config in its own DTSI
- Drop the unused USB regulator config
- Add proper thermal zone for the CPU
* tag 'ux500-dts-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500: Update thermal zone
ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree
ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi
ARM: ux500: improve BU21013 touchpad bindings
ARM: dts: ux500: Drop TV-out muxgroup on HREFs
Link: https://lore.kernel.org/r/CACRpkdZ9Xvx+rg-hFVgG61_i2CdQSs+nZq5FXkkK2-3Ce9ooWg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Disable the kirkwood RTC that doesn't work on the ts219 board
-----BEGIN PGP SIGNATURE-----
iFwEABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXWZPAQAKCRALBhiOFHI7
1XDhAJiWiPskIJ8+YYuSzyf7N7ukmN8ZAJ4sz+nfLMBlC9YiOaAI+eFywZUHfQ==
=hvyg
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.4-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.4 (part 1)
- Disable the kirkwood RTC that doesn't work on the ts219 board
* tag 'mvebu-dt-5.4-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: ts219: disable the SoC's RTC
Link: https://lore.kernel.org/r/878srdzjpj.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: ZII i.MX7 RMU2, Kontron i.MX6UL N6310, and
PHYTEC phyBOARD-Segin based on i.MX6ULL.
- A series from Andrey Smirnov to update vf610-zii boards on I2C
pinmux, switch watchdog, GPIO expander IRQ.
- Move GIC node into soc node for i.MX6 SoCs.
- Add OV5645 camera support for imx6qdl-wandboard board.
- Drop unneeded snvs_pwrkey node for imx7d-zii-rpu2 and imx7-colibri.
- Use simple-mfd instead of simple-bus for i.MX6 ANATOP.
- Move the native-mode property inside the display-timings node for
various i.MX25 and i.MX27 boards.
- Add EDMA devices for i.MX7ULP SoC.
- A series from Stefan Riedmueller to update imx6ul-phytec-segin board
on various devices.
- Use OF graph to describe the display for opos6uldev board.
- Misc random updates on i.MX7/6 boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYpwdAAoJEFBXWFqHsHzOpjMH/ArmJ/FlGDFmyffpXIT1qQdu
vyHdwySvCtftUsypDAhPSD43eFAOwqqfZR8b05UA+LE3TYKildxu4X2eEK2eFVn9
d97AEUuC49utHv9kf28kVPX0atI3QgqwJOW8/Xa1dlJl8CZN4GupmbLzYl9w6zF/
ii1WCzfnKjCQRW7s6+vFGqSdBnT1QXGSVXSYv5JI9MDh2qCzuYB1AI11CEnemYAq
pgJdTtdgW5g8sn8NHoAzQ9nUsq2IPkBHZzmt38eVk2YyvOmrMnpktNlBzMIBGaCJ
q6tmU7GaLrgcXe/lQMApBZ21jieAeKLWY+mdYN+kg1EumZHzllfitBZKYcL7mVs=
=DoYY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree changes for 5.4:
- New board support: ZII i.MX7 RMU2, Kontron i.MX6UL N6310, and
PHYTEC phyBOARD-Segin based on i.MX6ULL.
- A series from Andrey Smirnov to update vf610-zii boards on I2C
pinmux, switch watchdog, GPIO expander IRQ.
- Move GIC node into soc node for i.MX6 SoCs.
- Add OV5645 camera support for imx6qdl-wandboard board.
- Drop unneeded snvs_pwrkey node for imx7d-zii-rpu2 and imx7-colibri.
- Use simple-mfd instead of simple-bus for i.MX6 ANATOP.
- Move the native-mode property inside the display-timings node for
various i.MX25 and i.MX27 boards.
- Add EDMA devices for i.MX7ULP SoC.
- A series from Stefan Riedmueller to update imx6ul-phytec-segin board
on various devices.
- Use OF graph to describe the display for opos6uldev board.
- Misc random updates on i.MX7/6 boards.
* tag 'imx-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: vf610-zii-scu4-aib: Configure IRQ line for GPIO expander
ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards
ARM: dts: vf610-zii-cfu1: Slow I2C0 down to 100 kHz
ARM: dts: pbab01: correct rtc vendor
ARM: vf610-zii-cfu1: Add node for switch watchdog
ARM: dts: imx6: drop gpmi-nand address and size cells
ARM: dts: imx6: replace simple-bus by simple-mfd for anatop
ARM: dts: imx6qdl-colibri: add phy to fec
ARM: dts: imx7-colibri: add recovery for I2C for iMX7
ARM: dts: imx7-colibri: Add sleep pinctrl to ethernet
ARM: dts: imx7-colibri: prepare module device tree for FlexCAN
ARM: dts: imx7-colibri: disable HS400
ARM: dts: imx7-colibri: make sure module supplies are always on
ARM: dts: imx7d: cl-som-imx7: add compatible for phy
ARM: dts: imx7d: cl-som-imx7: make ethernet work again
ARM: dts: imx6ul: Add csi node
ARM: dts: imx25: mbimxsd25: native-mode is part of display-timings
ARM: dts: apf27dev: native-mode is part of display-timings
ARM: dts: edb7211: native-mode is part of display-timings
ARM: dts: imx27-phytec-phycore-rdk: native-mode is part of display-timings
...
Link: https://lore.kernel.org/r/20190825153237.28829-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove regulator-boot-off properties that we never had in the mainline
kernel so they won't do anything. We add stdout-path for gta04, and
make am335x-boneblue use am335x-osd335x-common.dtsi file.
-----BEGIN PGP SIGNATURE-----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=Utq2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
dts changes for omap variants for v5.4
Remove regulator-boot-off properties that we never had in the mainline
kernel so they won't do anything. We add stdout-path for gta04, and
make am335x-boneblue use am335x-osd335x-common.dtsi file.
* tag 'omap-for-v5.4/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblue: Use of am335x-osd335x-common.dtsi
ARM: dts: gta04: define chosen/stdout-path
ARM: dts: omap3-n950-n9: Remove regulator-boot-off property
ARM: dts: am335x-cm-t335: Remove regulator-boot-off property
Link: https://lore.kernel.org/r/pull-1566599057-142651@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXV/6JgAKCRDj7w1vZxhR
xc+VAQDjZWvNeMX75qsrz7Jbdy7jlbJJ/oDFBGx3C4clcTn7tgD6AsHeM760Pc6o
4a7G5DGcJakuFGsb1s4hNQOylmG3IQ4=
=pXxO
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights
- odroid-c1: use MAC address from efuse
- add VDD_EE regulator to several boards
-----BEGIN PGP SIGNATURE-----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=zCaj
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.4
Highlights
- odroid-c1: use MAC address from efuse
- add VDD_EE regulator to several boards
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: odroidc1: use the MAC address stored in the eFuse
ARM: dts: meson8b: mxq: add the VDDEE regulator
ARM: dts: meson8b: odroidc1: add the VDDEE regulator
ARM: dts: meson8b: ec100: add the VDDEE regulator
ARM: dts: meson8b: add the PWM_D output pin
ARM: dts: meson8b: add ethernet fifo sizes
Link: https://lore.kernel.org/r/7hzhk3bi96.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
areas and also a 100ms speedup as a delay isn't needed anymore.
New boards are Tiger and Fievel from the Veyron family and the Mecer Xtreme
Mini S6, which I think is the first consumer-grade rk3229-based device in
the kernel.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl1X/0cQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgT2RB/0X8SGcSRLL6vGCBH4vbATtnh1ceh6O2GA8
NO1N+OgQjPQWQyVx8ZWb7oaWgECwnXn41WT1HP9t0KB4w4sILZEswJrDRKV0dj1o
g+8tpgdxzJ7YF+vEkW1EcdPU2d1bRBJZ4qN38t2/StWg5WCrfThM2zBEUEJyWHpr
QYfSVXmhvPHISyZE+/k0tdgBhEi3KQph7ZVPhsmhugd1PeIV5lMDTVx4H7ljdnuC
/rVM/Yj+93r23bMgp6VGaMQmidlymYWCwxdTM4d4vDozViaykJ38BwDKVzfXX99y
hxA2BxKjp+37tuy4r4IO3kuqTEH6b4rvZzdNxJwBrGmIcBfv3n9j
=b567
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for Veyron devices with cleanups in the display and wifi
areas and also a 100ms speedup as a delay isn't needed anymore.
New boards are Tiger and Fievel from the Veyron family and the Mecer Xtreme
Mini S6, which I think is the first consumer-grade rk3229-based device in
the kernel.
* tag 'v5.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: add device tree for Mecer Xtreme Mini S6
Revert "ARM: dts: rockchip: add startup delay to rk3288-veyron panel-regulators"
ARM: dts: rockchip: Add pin names for rk3288-veyron fievel
ARM: dts: rockchip: A few fixes for veyron-{fievel,tiger}
ARM: dts: rockchip: Cleanup style around assignment operator
ARM: dts: rockchip: add veyron-tiger board
ARM: dts: rockchip: add veyron-fievel board
dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-{fievel,tiger}
ARM: dts: rockchip: consolidate veyron panel and backlight settings
ARM: dts: rockchip: move rk3288-veryon display settings into a separate file
ARM: dts: rockchip: Limit WiFi TX power on rk3288-veyron-jerry
ARM: dts: rockchip: Specify rk3288-veyron-minnie's display timings
ARM: dts: rockchip: Specify rk3288-veyron-chromebook's display timings
Link: https://lore.kernel.org/r/1611583.rKl1eQBRh8@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
