This adds a devicetree for the Kobo Clara HD Ebook reader. It
is on based on boards called "e60k02". It is equipped with an
imx6sll SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Netronix board E60K02 can be found some several Ebook-Readers,
at least the Kobo Clara HD and the Tolino Shine 3. The board
is equipped with different SoCs requiring different pinmuxes.
For now the following peripherals are included:
- LED
- Power Key
- Cover (gpio via hall sensor)
- RC5T619 PMIC (the kernel misses support for rtc and charger
subdevices).
- Backlight via lm3630a
- Wifi sdio chip detection (mmc-powerseq and stuff)
It is based on vendor kernel but heavily reworked due to many
changed bindings.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Enable L2 cache parity and ECC on a Armada XP SoC family and allow
to use in on the Armada 38x SoCs too.
- Use correct name for the rs5c372a on synology (Kirkwood based)
- Rename "sa-sram" node to "sram" on dove
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXb9ANAAKCRALBhiOFHI7
1YxGAJ42trDdNhPczQeHvNx2UcvmSKU8rQCfdNMvDGGosrbJ/aWklGPQfU4iano=
=0o2E
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.5-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.5 (part 1)
- Enable L2 cache parity and ECC on a Armada XP SoC family and allow
to use in on the Armada 38x SoCs too.
- Use correct name for the rs5c372a on synology (Kirkwood based)
- Rename "sa-sram" node to "sram" on dove
* tag 'mvebu-dt-5.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp: add label to sdram-controller node
ARM: dts: mvebu: add sdram controller node to Armada-38x
ARM: dts: armada-xp: enable L2 cache parity and ecc on db-xc3-24g4xg
ARM: dts: dove: Rename "sa-sram" node to "sram"
ARM: dts: kirkwood: synology: Fix rs5c372 RTC entry
Link: https://lore.kernel.org/r/8736f44q9l.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
Enables the Tegra VDE driver by default. This is currently in staging
but can be used with existing userspace to do hardware-accelerated video
decoding of H.264 streams.
-----BEGIN PGP SIGNATURE-----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=ziJD
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig
ARM: tegra: Default configuration changes for v5.5-rc1
Enables the Tegra VDE driver by default. This is currently in staging
but can be used with existing userspace to do hardware-accelerated video
decoding of H.264 streams.
* tag 'tegra-for-5.5-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable Tegra VDE driver in tegra_defconfig
Link: https://lore.kernel.org/r/20191102144521.3863321-7-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds support for CPU frequency scaling on Tegra20 and Tegra30, EMC
frequency scaling on Tegra30, SMMU support for VDE on Tegra30, the
STMPE ADC found on Toradex T30 modules as well as fixes for eDP
support on Venice2.
-----BEGIN PGP SIGNATURE-----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=rlo7
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.5-rc1
Adds support for CPU frequency scaling on Tegra20 and Tegra30, EMC
frequency scaling on Tegra30, SMMU support for VDE on Tegra30, the
STMPE ADC found on Toradex T30 modules as well as fixes for eDP
support on Venice2.
* tag 'tegra-for-5.5-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cardhu-a04: Add CPU Operating Performance Points
ARM: tegra: cardhu-a04: Set up voltage regulators for DVFS
ARM: tegra: trimslice: Add CPU Operating Performance Points
ARM: tegra: paz00: Add CPU Operating Performance Points
ARM: tegra: paz00: Set up voltage regulators for DVFS
ARM: tegra: Add CPU Operating Performance Points for Tegra30
ARM: tegra: Add CPU Operating Performance Points for Tegra20
ARM: tegra: Add Tegra30 CPU clock
ARM: tegra: Add Tegra20 CPU clock
ARM: tegra: Add External Memory Controller node on Tegra30
ARM: tegra: nyan-big: Add timings for RAM codes 4 and 6
ARM: tegra: Connect SMMU with Video Decoder Engine on Tegra30
ARM: tegra: Add eDP power supplies on Venice2
ARM: tegra: Add SOR0_OUT clock on Tegra124
ARM: tegra: Add stmpe-adc DT node to Toradex T30 modules
Link: https://lore.kernel.org/r/20191102144521.3863321-6-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Contains two fixes for CPU idle and suspend/resume on early Tegra SoCs.
-----BEGIN PGP SIGNATURE-----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=QeJo
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm-core' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
ARM: tegra: Core changes for v5.5-rc1
Contains two fixes for CPU idle and suspend/resume on early Tegra SoCs.
* tag 'tegra-for-5.5-arm-core' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Use WFE for power-gating on Tegra30
ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()
Link: https://lore.kernel.org/r/20191102144521.3863321-5-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
multiple boards, one for the new crypto driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXb2ovAAKCRDj7w1vZxhR
xfeOAP9peTfpsETYjozV4ZmKKzoMS/+KtKtPw16i+W+cgMezDQEA3e7JtpL1oC/P
qYgJVeOB2m6dHXuZj3xZEabglbP5pA4=
=MhwW
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config-for-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/defconfig
Two new drivers enabled in sunxi_defconfig: one for the PHY found on
multiple boards, one for the new crypto driver.
* tag 'sunxi-config-for-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: configs: sunxi: Enable MICREL_PHY
ARM: configs: sunxi: add new Allwinner crypto options
Link: https://lore.kernel.org/r/27125172-7ce8-427e-83f9-8e9bd69d50a4.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop legacy DT clock support on R-Car Gen2.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXbxCkQAKCRCKwlD9ZEnx
cL09AP9GvKuMWdaC6a2XLhEHe3DVuKLGhC7FW6xq5xD8F56GEQEAy2dtqqvj9DNb
KTglZePVJNCYAcrY7RM8qZEwHDJxLAo=
=S/Vk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-soc-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/soc
Renesas ARM SoC updates for v5.5
- Drop legacy DT clock support on R-Car Gen2.
* tag 'renesas-arm-soc-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: shmobile: rcar-gen2: Drop legacy DT clock support
Link: https://lore.kernel.org/r/20191101155842.31467-3-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
- Refresh shmobile_defconfig for v5.4-rc1.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXbxCFgAKCRCKwlD9ZEnx
cJ0/AQCLLQVNK2ZIO0uOJV1KuFNVBbLbOorFi8YRkRY2GPIkiwEAiwSARu7Daz//
M24hs05l3DkfDwhKBj9z1I2EM/DVyAk=
=hEYM
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-defconfig-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/defconfig
Renesas ARM defconfig updates for v5.5
- Refresh shmobile_defconfig for v5.4-rc1.
* tag 'renesas-arm-defconfig-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: shmobile: defconfig: Refresh for v5.4-rc1
Link: https://lore.kernel.org/r/20191101155842.31467-2-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes adds the PRM reset driver nodes for am3/4, omap4/5
and dra7 SoCs. The reset driver changes make it easier to add support for
various accelerators for TI SoCs in a more generic way.
Note that this branch is based on the PRM reset driver changes branch.
-----BEGIN PGP SIGNATURE-----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=4DAS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/prm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
PRM reset control dts changes for v5.5 merge window
This series of changes adds the PRM reset driver nodes for am3/4, omap4/5
and dra7 SoCs. The reset driver changes make it easier to add support for
various accelerators for TI SoCs in a more generic way.
Note that this branch is based on the PRM reset driver changes branch.
* tag 'omap-for-v5.5/prm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add PRM data
ARM: dts: am43xx: Add PRM data
ARM: dts: am33xx: Add PRM data
ARM: dts: omap4: add PRM nodes
ARM: dts: dra7: add PRM nodes
soc: ti: omap-prm: add omap5 PRM data
soc: ti: omap-prm: add am4 PRM data
soc: ti: omap-prm: add dra7 PRM data
soc: ti: omap-prm: add data for am33xx
soc: ti: omap-prm: add omap4 PRM data
soc: ti: omap-prm: add support for denying idle for reset clockdomain
soc: ti: omap-prm: poll for reset complete during de-assert
soc: ti: add initial PRM driver with reset control support
dt-bindings: omap: add new binding for PRM instances
Link: https://lore.kernel.org/r/pull-1572623173-281197@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Make sure UART3, where the console is, is called ttyS2. That is
consistent with the early console.
Link: https://lore.kernel.org/r/20191031163455.1711872-5-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Ponted out by DTC:
<stdout>: Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Link: https://lore.kernel.org/r/20191031163455.1711872-4-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a typo there that rightfully upsets DTS:
<stdout>: Warning (simple_bus_reg): /soc/watchdog@2c000620: simple-bus
unit address format error, expected "e0000620"
Link: https://lore.kernel.org/r/20191031163455.1711872-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
It should have one and DTC is indeed unhappy about its absence:
<stdout>: Warning (unit_address_vs_reg): /soc/clocks: node has a reg or
ranges property, but no unit name
Link: https://lore.kernel.org/r/20191031163455.1711872-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Increase the max number of GPIOs from default 512 to 1024 for ASPEED
platforms, because Facebook Yamp (AST2500) BMC platform has total 594
GPIO pins (232 provided by ASPEED SoC, and 362 by I/O Expanders).
Link: https://lore.kernel.org/r/20191031014040.12898-1-rentao.bupt@gmail.com
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add GPIO controllers for RDA8810PL SoC. There are 4 GPIO controllers
in this SoC with maximum of 32 gpios. Except GPIOC, all controllers
are capable of generating edge/level interrupts from first 8 lines.
Link: https://lore.kernel.org/r/20191030101154.6312-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- drop the ARCH_MULTI_V7 dependency in the sub-menu of ARCH_HISI
since ARCH_HISI depends on ARCH_MULTI_V7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5K1D
-----END PGP SIGNATURE-----
Merge tag 'hisi-armv7-soc-for-5.5' of git://github.com/hisilicon/linux-hisi into arm/soc
ARM: mach-hisi: Hisilicon SoC updates for 5.5
- drop the ARCH_MULTI_V7 dependency in the sub-menu of ARCH_HISI
since ARCH_HISI depends on ARCH_MULTI_V7
* tag 'hisi-armv7-soc-for-5.5' of git://github.com/hisilicon/linux-hisi:
ARM: hisi: drop useless depend on ARCH_MULTI_V7
Link: https://lore.kernel.org/r/5DB9593D.9050904@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for_5.5/driver-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
memory: emif: remove set but not used variables 'cs1_used' and 'custom_configs'
soc: ti: omap-prm: fix return value check in omap_prm_probe()
soc: ti: omap-prm: add omap5 PRM data
soc: ti: omap-prm: add am4 PRM data
soc: ti: omap-prm: add dra7 PRM data
soc: ti: omap-prm: add data for am33xx
soc: ti: omap-prm: add omap4 PRM data
soc: ti: omap-prm: add support for denying idle for reset clockdomain
soc: ti: omap-prm: poll for reset complete during de-assert
soc: ti: add initial PRM driver with reset control support
dt-bindings: omap: add new binding for PRM instances
Link: https://lore.kernel.org/r/1572372856-20598-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The common ARM architecture code provides a generic function to exit
coherency called v7_exit_coherency_flush(). Replace the machine
specific implementation using the generic function.
Tested on a i.MX 6Dual by hotplugging the secondary CPU under load
through sysfs several 1000 times.
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdt+NxAAoJEFBXWFqHsHzO9dQIAItV9GBySkuQ74/LBBp9WHfi
Y708jUcbm/oEkic3bW+RdXpr+Xo3nP1E1VrdogqwWZStePS4JQtRWs7/+NAC/aiw
wrUDoCXnZYiSLtp+f/1OSs7mUSG13Ip+Um9VxjI1AI9ld1YKg8sSeg0Xlk5oNsk4
1/2c1P9nW0XjWMkpLqYzIbbtb+sisCX0/Ftyxw7vrjhpgJSDDUTE37IFgmdskZg6
ILl00chE4E+8AlLm9kdtqOgzihtFVbSIrhF99gbF6R9vZQGoYgOE3QM2YG+qhEOd
56bQTJJRVwutSbBGGv1ya/J5cmtZYDzoi10JEEQ+zkyrcU+G3qj9+8/wZORba5o=
=0kUv
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 2nd round:
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
* tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
Link: https://lore.kernel.org/r/20191029110334.GA20928@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
This is an Allwinner H3 based board, with 512MB ram, a USB OTG port,
microsd slot, an onboard AP6212A wifi/bluetooth module, and a CSI
connector.
Full details and schematic available from vendor:
http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Update the defconfig for Renesas ARM boards:
- Drop CONFIG_ARM_ERRATA_754322=y (auto-enabled since commit
2eced4607a ("soc: renesas: Enable ARM_ERRATA_754322 for
affected Cortex-A9")),
- Drop CONFIG_MTD_M25P80=y (removed in commit b35b9a1036 ("mtd:
spi-nor: Move m25p80 code in spi-nor.c")),
- Drop CONFIG_LCD_CLASS_DEVICE=n (no longer auto-enabled since commit
bcd69da98e ("video: backlight: Drop default m for
{LCD,BACKLIGHT_CLASS_DEVICE}")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191025135325.32242-1-geert+renesas@glider.be
Simplify the Yamp device tree by using the common dtsi.
In addition this enables the following the second firmware flash and the
eMMC device in slot #1.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify the Minipack device tree by using the common dtsi.
In addition this enables the enabling the second firmware flash, and
updates it's size from 32MB to 64MB. It also enables the eMMC device in
slot #1.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify the CMM device tree by using the common dtsi.
In addition this enables the second firmware flash and the emmc device
in slot #0.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This common descirption is included by all Facebook AST2500 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add in a gpio-keys section to the Rainier device tree source, add in the
power supply presence GPIOs.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fix the size of the Proc VRM card's eeprom used for vpd storage. The
size is changed from 64Kbit to 128Kbit.
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Requesting pinmux configuration is done at driver probe time. The LPC IP
is composed of many sub-devices, each with their own driver, and no
driver exists for the entire IP block. Avoid having each sub-device
request the LPC pinmux by just hogging it in the pinctrl node.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Like most OpenPower machines the VUART is expected to be at /dev/ttyS5
for communication with the host over LPC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added eeproms for the below VPD devices
- BMC
- TPM
- System Planar
- DCM 0 VRM
- DCM 1 VRM
- Base Op panel
- Lcd Op panel
- DASD (All)
- PCIe Cards (All)
Signed-off-by: Jinu Joy Thomas <jinu.joy.thomas@in.ibm.com>
Reviewed-by: Santosh Puranik <santosh.puranik.ibm@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
OpenBMC requires a window the same size as the image being loaded.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The UART has an issue on A0 that can be worked around by using the
Synopsis driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The UARTs on the AST2600 A0 have a known issue that can be worked around
by using the Synopsys driver.
Tested-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We need to ungate RCLK on AST2500- and AST2600-based platforms for RMII
to function. RMII interfaces are commonly used for NCSI.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
uart1 and uart3 had existing pin definitions for the rts/cts pairs.
Add definitions for uart2 as well.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Include support for Micrel KSZ9031 PHY driver in sunxi_defconfig,
which fixes issues of link not coming up at boot time with
certain link partners.
Micrel KSZ9031 PHY chip is used on Olimex A20-OLinuXino-LIME2
boards.
The errata fix itself has been implemented in commit
"3aed3e2a143c96: net: phy: micrel: add Asym Pause workaround"
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the new Allwinner crypto configs to sunxi_defconfig
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG/RSA algorithms.
It could be found on Allwinner SoC A80 and A83T
This patch adds it on the Allwinner A80 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG/RSA algorithms.
It could be found on Allwinner SoC A80 and A83T
This patch adds it on the Allwinner A83T SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic accelerator that supports
many algorithms.
It could be found on most Allwinner SoCs.
This patch enables the Crypto Engine on the Allwinner H3 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic offloader that supports
many algorithms.
It could be found on most Allwinner SoCs.
This patch enables the Crypto Engine on the Allwinner R40 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Now that the blkcipher algorithm type has been removed in favor of
skcipher, rename the crypto_blkcipher kernel module to crypto_skcipher,
and rename the config options accordingly:
CONFIG_CRYPTO_BLKCIPHER => CONFIG_CRYPTO_SKCIPHER
CONFIG_CRYPTO_BLKCIPHER2 => CONFIG_CRYPTO_SKCIPHER2
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Keep the FMC controller chips at a safe 50 MHz rate and use 100 MHz
for the PNOR on the machines using a AST2500 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Use the SoC-specific compatible strings instead.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adds a new power_green led to show the host state.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This way enabling the MDIO controllers automatically requests the right
pinmux configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The binding was updated to better reflect the intended use of the
hardware and the existing function/groups for SD3 were dropped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 u-boot and kernel images have outgrown the OpenBMC layout.
While BMC machines use 128MB SPI NOR chips, we only have 64MB on the EVB
so use a layout that has a smaller region for the ro and rw filesystems.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add fan controllers, regulators, temperature sensors, power supplies
and regulators.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier contains two NCSI network devices.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier is a new IBM server with POWER host processors and an AST2600
BMC.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is an alternate layout used by OpenBMC systems that require more
space on the BMC's flash. In addition to more space for the rootfs, it
supports a larger u-boot and Linux kernel FIT image.
The division of space is as follows:
u-boot + env: 1MB
kernel/FIT: 9MB
rwfs: 86MB
rofs: 32MB
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Change BMC init-ok from GPIO to LED, which needs to blink when BMC
initialization is complete.
Use TAB to align some lines.
Signed-off-by: Chicago Duan <duanzhijia01@inspur.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable all the I2C busses on Tacoma and add the I2C slave devices that
exist on the busses.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Everything is the same as G5, except the devices have their own
interrupt now.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 has two VUART devices.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 has 208 normal GPIO pins and 36 1.8V GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the eMMC controller and limit it to 52MHz to avoid the host
controller reporting bus error conditions.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Caching dates is never a good idea ;-)
Fixes: 7253b85cc6 ("ARM: 7541/1: Add ARM ERRATA 775420 workaround")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The arch/arm/kernel/tcm.c should include <asm/tcm.h>
for declarations of tcm_alloc, tcm_free and other
functions. Fixes the following sparse warnings:
arch/arm/kernel/tcm.c:74:6: warning: symbol 'tcm_alloc' was not declared. Should it be static?
arch/arm/kernel/tcm.c:92:6: warning: symbol 'tcm_free' was not declared. Should it be static?
arch/arm/kernel/tcm.c:98:6: warning: symbol 'tcm_dtcm_present' was not declared. Should it be static?
arch/arm/kernel/tcm.c:104:6: warning: symbol 'tcm_itcm_present' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The dtcm_end and itcm_end are not exported or used
elsewhere, so make them static to remove the following
sparse warnign:
arch/arm/kernel/tcm.c:33:5: warning: symbol 'dtcm_end' was not declared. Should it be static?
arch/arm/kernel/tcm.c:34:5: warning: symbol 'itcm_end' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
iomap.c needs <asm/vga.h> for the definition vga_base
to avoid the following warning:
arch/arm/mm/iomap.c:13:15: warning: symbol 'vga_base' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The rate pointer in parse_dt_topology is a pointer to a
__be32, not a u32. This fixes the following sparse warning:
arch/arm/kernel/topology.c:128:43: warning: incorrect type in argument 1 (different base types)
arch/arm/kernel/topology.c:128:43: expected restricted __be32 const [usertype] *p
arch/arm/kernel/topology.c:128:43: got unsigned int const [usertype] *[assigned] rate
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The get_signal_page() function is defined in signal.c and used in
process.c but there is no shared definition. Add one in signal.h to
silence the following warning:
arch/arm/kernel/signal.c:683:13: warning: symbol 'get_signal_page' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The psci_cpu_{disable,die,kill} functions are not
exported, so make them static to avoid the following
warnings:
arch/arm/kernel/psci_smp.c:54:5: warning: symbol 'psci_cpu_disable' was not declared. Should it be static?
arch/arm/kernel/psci_smp.c:67:6: warning: symbol 'psci_cpu_die' was not declared. Should it be static?
arch/arm/kernel/psci_smp.c:79:5: warning: symbol 'psci_cpu_kill' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The maximum divider value for DPLL4 M4 divider appears wrong. For most
OMAP3 family SoCs this is 16, but it is defined as 32, which is maybe
only valid for omap36xx. To avoid any overflows in trying to write this
register, set the max to 16 for all omap3 family, except omap36xx. For
omap36xx the maximum is set to 31, as it appears value 32 is not working
properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
All boards using rk3288-veyron-analog-audio.dtsi have HDMI audio.
Specify the support of HDMI audio on machine driver using
rockchip,hdmi-codec property so machine driver creates HDMI audio device.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028071930.145899-6-cychiang@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Daniele reported that issue previously fixed in c41f9ea998
("drivers: dma-coherent: Account dma_pfn_offset when used with device
tree") reappear shortly after 43fc509c3e ("dma-coherent: introduce
interface for default DMA pool") where fix was accidentally dropped.
Lets put fix back in place and respect dma-ranges for reserved memory.
Fixes: 43fc509c3e ("dma-coherent: introduce interface for default DMA pool")
Reported-by: Daniele Alessandrelli <daniele.alessandrelli@gmail.com>
Tested-by: Daniele Alessandrelli <daniele.alessandrelli@gmail.com>
Tested-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Looks like omap3 RNG is similar to the omap2 rng, let's get it working
by configring the dts node for it.
We must also add rng_ick to core_l4_clkdm as noted by Adam Ford.
And please note that the RNG is likely disabled on HS devices. At least
n900 does not have it accessible, and instead omap3-rom-rng driver must
be used. So let's tag RNG as disabled on n900 as noted by Pali Rohár
<pali.rohar@gmail.com>.
On am3517 at least the clocks need to be configured to get it working
as noted by Adam Ford, so let's tag it disabled for now.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Signed-off-by: Tony Lindgren <tony@atomide.com>
Utilize common Tegra30 CPU OPP table. CPU DVFS is available now on
Cardhu A04.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set minimum and maximum voltages, and couple CPU/CORE regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Utilize common Tegra20 CPU OPP table. CPU voltage scaling is available
now on TrimSlice.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Utilize common Tegra20 CPU OPP table. CPU DVFS is available now on
AC100.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set minimum and maximum voltages, and couple CPU/CORE/RTC regulators.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Operating Point are specified per HW version. The OPP voltages are kept
in a separate DTSI file because some boards may not define CPU regulator
in their device-tree if voltage scaling isn't necessary for them.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Operating Point are specified per HW version. The OPP voltages are kept
in a separate DTSI file because some boards may not define CPU regulator
in their device-tree if voltage scaling isn't necessary, like for example
in a case of tegra20-trimslice which is outlet-powered device.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add timings for RAM codes 4 and 6 and a timing for 528mHz of RAM code 1,
which was missed due to the clock driver bug that is fixed now in all of
stable kernels.
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The power supplies needed to drive eDP on Venice2 were never hooked up,
so things only worked because those regulators are already enabled by
other devices.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the stmpe-adc DT node as found on Toradex T30 modules
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Turned out that WFI doesn't work reliably on Tegra30 as a trigger for
the power-gating, it causes CPU hang under some circumstances like having
memory controller running of PLLP. The TRM doc states that WFI should be
used for the Big-Little "Cluster Switch", while WFE for the power-gating.
Hence let's use the WFE for CPU0 power-gating, like it is done for the
power-gating of a secondary cores. This fixes CPU hang after entering LP2
with memory running off PLLP.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is an unfortunate typo in the code that results in writing to
FLOW_CTLR_HALT instead of FLOW_CTLR_CSR.
Cc: <stable@vger.kernel.org>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The video decoder driver was tested by time and works absolutely fine.
The reason why it is in staging is because it doesn't provide common V4L
interface yet, this shouldn't stop driver enabling in the defconfig since
our userspace (libvdpau-tegra) provides combined acceleration of decoding
and displaying without use of V4L.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PRCM_PWROFF_GATING_REG has CPU0 at bit 4 on A83T. So without this
patch, instead of gating the CPU0, the whole cluster was power gated,
when shutting down first CPU in the cluster.
Fixes: 6961275e72 ("ARM: sun8i: smp: Add support for A83T")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Without enabling keep-power-in-suspend, we can't wake the device
up using WOL packet, and the log is flooded with these messages
on resume:
sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command
sunxi-mmc 1c10000.mmc: send stop command failed
sunxi-mmc 1c10000.mmc: data error, sending stop command
So to make the WiFi really a wakeup-source, we need to keep it powered
during suspend.
Fixes: 0e23372080 ("arm: dts: sun8i: Add the TBS A711 tablet devicetree")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Enable the CONFIG_TOUCHSCREEN_DA9052 option, so that touchscreen
can be functional by default on imx53-qsb.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The name s5p_usb_phy_init() suggests it is shared with S5Pv210 platform,
but it is not. It is specific to S3C64xx, so make it clear in the
name.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The name s3c64xx_spi_setname() suggests it is shared with S3C64xx
platform, but except of contents it is not. It is called only by
S3C24xx code, so make it clear in the name.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Highlights:
----------
MPU part:
-Add and enable ADC support on stm32mp157a-dk1
-Add DAC support on stm32mp157c-ed1
-Add and enable VREFBUF support on stm32mp157a-dk1
-Add focaltech touchscreen on stm32mp157c-dk2
-Add hdmi support on stm32mp157a-dk1
-Fix issues seen during YAML DT validation
-Fix regulators issues for all MPU boards
MCU part:
-Fix issues seen during YAML DT validation
-----BEGIN PGP SIGNATURE-----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=X4PA
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.5, round 1
Highlights:
----------
MPU part:
-Add and enable ADC support on stm32mp157a-dk1
-Add DAC support on stm32mp157c-ed1
-Add and enable VREFBUF support on stm32mp157a-dk1
-Add focaltech touchscreen on stm32mp157c-dk2
-Add hdmi support on stm32mp157a-dk1
-Fix issues seen during YAML DT validation
-Fix regulators issues for all MPU boards
MCU part:
-Fix issues seen during YAML DT validation
* tag 'stm32-dt-for-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: remove useless dma-ranges property for stm32f469
ARM: dts: stm32: remove useless dma-ranges property for stm32f429
ARM: dts: stm32: disable active-discharge for vbus_otg on stm32mp157a-avenger96
ARM: dts: stm32: Fix active discharge usage on stm32mp157
ARM: dts: stm32: change default minimal buck1 value on stm32mp157
ARM: dts: stm32: add PWR regulators support on stm32mp157
ARM: dts: stm32: remove useless interrupt from dsi node for stm32f469
ARM: dts: stm32: add hdmi audio support to stm32mp157a-dk1 board
ARM: dts: stm32: Add DAC support to stm32mp157c-ed1
ARM: dts: stm32: Add DAC pins used on stm32mp157c-ed1
ARM: dts: stm32: fix regulator-sd_switch node on stm32mp157c-ed1 board
ARM: dts: stm32: remove usb phy-names entries on stm32mp157c-ev1
ARM: dts: stm32: fix joystick node on stm32f746 and stm32mp157c eval boards
ARM: dts: stm32: fix memory nodes to match with DT validation tool
ARM: dts: stm32: add focaltech touchscreen on stm32mp157c-dk2 board
ARM: dts: stm32: enable ADC support on stm32mp157a-dk1
ARM: dts: stm32: add ADC pins used on stm32mp157a-dk1
ARM: dts: stm32: Enable VREFBUF on stm32mp157a-dk1
ARM: dts: stm32: move ltdc pinctrl on stm32mp157a dk1 board
Link: https://lore.kernel.org/r/02c39510-f36d-abbb-c76f-49aff07c0a08@st.com
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM/ARM64 has counters halt_successful_poll, halt_attempted_poll,
halt_poll_invalid, and halt_wakeup but never exposed those in debugfs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1572164390-5851-1-git-send-email-borntraeger@de.ibm.com
i.MX6/7 SoCs have a 64-bit SoC unique ID stored in OCOTP,
it can be used as SoC serial number, add this support for
i.MX6Q/6DL/6SL/6SX/6SLL/6UL/6ULL/6ULZ/7D, see below example
on i.MX6Q:
root@imx6qpdlsolox:~# cat /sys/devices/soc0/serial_number
240F31D4E1FDFCA7
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the parallel panel that is supported is the CLAA WVGA panel,
which is the one that comes with the i.MX51 Babbage board.
The default parallel panel that goes with the imx53-qsb board is
the Seiko 43WVF1G LCD, so switch to the Seiko one.
While at it convert to DRM bindings.
The parallel display still remains disabled as the default display
port is the TVE output.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL 14x14 EVK board, mag3110's power is controlled by
sensor regulator, assign power supplies for mag3110 driver
to do power management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name is supposed to be generic, use "magnetometer" instead
of "mag3110" for magnetometer node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL 14x14 EVK board, sensors' power are controlled
by GPIO5_IO02, add GPIO regulator for sensors to manage
their power.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX GPT driver ONLY supports 1 instance, i.MX6UL already has
GPT1 enabled by default, so GPT2 should be disabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This regulator supplies other devices and not only usb host1 so
rename it.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These changes make the WiFi on the APF6 board work again.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTS/CTS lines are wired to the Bluetooth chip so add uart-has-rtscts
property to uart2.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the mdio bus and the phy to the fec-node.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed ("pinctrl: imx: Allow parsing DT without
function nodes").
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With commit b5bbe22353 ("usb: phy: mxs: Disable external charger
detect in mxs_phy_hw_init()") in tree all of the necessary charger
setup is done by the USB PHY driver which covers all of the affected
i.MX6 SoCs.
NOTE: imx_anatop_usb_chrg_detect_disable() was also called for i.MX7D,
but looking at its datasheet it appears to have a different USB PHY IP
block, so executing i.MX6 charger disable configuration seems
unnecessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/iio/accel/mma8452.txt,
the correct interrupt-names are "INT1" and "INT2", so fix them
accordingly.
While at it, modify the node to only specify "INT2" since providing
two interrupts is not necessary or useful (the driver will only use
one).
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[andrew.smirnov@gmail.com modified the patch to drop INT1]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables the recovery mode now available.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds missing i2c recovery modes and corrects wrongly named
ones.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard of the Logic PD i.MX6 development kit has a power
button routed which can both power down and power up the board.
It can also wake the board from sleep. This functionality was
marked as disabled by default in imx6qdl.dtsi, so it needs to
be explicitly enabled for each board.
This patch enables the snvs power key again.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 770856f0da ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Cc: stable <stable@vger.kernel.org> #5.3+
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6dl-yapp4 Draco and Ursa boards use the I2C3 bus to control some
external devices through the /dev files.
So enable the I2C3 bus on all board variants, not just on Hydra.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The second UART is needed for 3D or MFD printer control.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The definitions of set_kernel_text_rw() and
set_kernel_text_ro() are in <asm/set_memory.h>
but this is not included in init.c which defines
these. Silence the following warnings by including
the <asm/set_memory.h> header.
arch/arm/mm/init.c:669:6: warning: symbol 'set_kernel_text_rw' was not declared. Should it be static?
arch/arm/mm/init.c:678:6: warning: symbol 'set_kernel_text_ro' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The set_section_perms() is not defined outside of the
init.c file, so make it static to avoid the following
warning:
arch/arm/mm/init.c:596:6: warning: symbol 'set_section_perms' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
There are some sparse warnings about type conversion in
the atags_to_fdt.c code, due to __be32 and __be64, so
fix the following:
- Change _be32 and __be64 where appropriate
- Change setprop() to take a 'void *'
- Change incorrect fdt32_to_cpu() on FDT_MAGIC
Fixes the following sparse warnings:
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:66:29: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:141:34: warning: cast to restricted __be32
arch/arm/boot/compressed/atags_to_fdt.c:182:60: warning: incorrect type in assignment (different base types)
arch/arm/boot/compressed/atags_to_fdt.c:182:60: expected unsigned long long [usertype]
arch/arm/boot/compressed/atags_to_fdt.c:182:60: got restricted __be64 [usertype]
arch/arm/boot/compressed/atags_to_fdt.c:184:60: warning: incorrect type in assignment (different base types)
arch/arm/boot/compressed/atags_to_fdt.c:184:60: expected unsigned long long [usertype]
arch/arm/boot/compressed/atags_to_fdt.c:184:60: got restricted __be64 [usertype]
arch/arm/boot/compressed/atags_to_fdt.c:187:62: warning: incorrect type in assignment (different base types)
arch/arm/boot/compressed/atags_to_fdt.c:187:62: expected unsigned int
arch/arm/boot/compressed/atags_to_fdt.c:187:62: got restricted __be32 [usertype]
arch/arm/boot/compressed/atags_to_fdt.c:189:62: warning: incorrect type in assignment (different base types)
arch/arm/boot/compressed/atags_to_fdt.c:189:62: expected unsigned int
arch/arm/boot/compressed/atags_to_fdt.c:189:62: got restricted __be32 [usertype]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The arch_timer_arch_init is defined in <asm/arch_timer.h> so include
that to fix the following sparse error:
arch/arm/kernel/arch_timer.c:31:12: warning: symbol 'arch_timer_arch_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the pcibios_report_status to <asm/pci.h> include to remove the
following sparse warning and to remove the extra definition in the
footbrdige dc21285.c driver:
arch/arm/kernel/bios32.c:59:6: warning: symbol 'pcibios_report_status' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The module_frob_arch_sections function is missing the header declaration
which is in <linux/moduleloader.h> so include that to fix the following
sparse warning:
arch/arm/kernel/module-plts.c:188:5: warning: symbol 'module_frob_arch_sections' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixup the following sparse warnings by making the functions and structures
static.
arch/arm/mm/dma-mapping.c:1562:6: warning: symbol '__arm_iommu_free_attrs' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1586:6: warning: symbol 'arm_iommu_free_attrs' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1592:6: warning: symbol 'arm_coherent_iommu_free_attrs' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1716:5: warning: symbol 'arm_coherent_iommu_map_sg' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1734:5: warning: symbol 'arm_iommu_map_sg' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1767:6: warning: symbol 'arm_coherent_iommu_unmap_sg' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1784:6: warning: symbol 'arm_iommu_unmap_sg' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1798:6: warning: symbol 'arm_iommu_sync_sg_for_cpu' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:1816:6: warning: symbol 'arm_iommu_sync_sg_for_device' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:2018:26: warning: symbol 'iommu_ops' was not declared. Should it be static?
arch/arm/mm/dma-mapping.c:2040:26: warning: symbol 'iommu_coherent_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid calling __pfn_to_phys twice.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
msm8974 has 11 sensors connected to a single TSENS IP. Define a thermal
zone for each of those sensors to expose the temperature of each zone.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Register upper-lower interrupt for the tsens controller.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The pca9535 gpio expander is present on the Rex baseboard, but missing
from the dtsi.
The pca9535 is on i2c2 bus which is common to the three SOM
variants (Basic/Pro/Ultra), thus it is activated by default.
Add also the new gpio controller and the associated interrupt line
MX6QDL_PAD_NANDF_CS3__GPIO6_IO16.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without configuring this pinctrl, the ID value can't be got correctly,
then, the dual-role switch can't work well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit a211b8c55f ("ARM: dts: imx6qdl-sabreauto: Add sensors")
a storm of accelerometer interrupts is seen:
[ 114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[ 114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[ 114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[ 114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[ 114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[ 114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[ 114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[ 114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[ 114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[ 114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[ 114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[ 114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[ 114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[ 114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[ 114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[ 114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[ 114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[ 114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[ 114.368830] 1f00: 20000013 ffffffff
[ 114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[ 114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[ 114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[ 114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[ 114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[ 114.411958] handlers:
[ 114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[ 114.422974] Disabling IRQ #260
CPU0 CPU1
....
260: 100001 0 gpio-mxc 31 Level mma8451
The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.
The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.
The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.
Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.
Fixes: a211b8c55f ("ARM: dts: imx6qdl-sabreauto: Add sensors")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ARCH_HISI depends on ARCH_MULTI_V7, no need to add this depend
to each sub-menu config, and use tabs where possible.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog
regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner
(phy regulators, PMU removal on A64, etc).
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl2zFiIPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3HtgQAI+fVql3qk2qnDhP2CJihxPWTl5tyM26hvRH
dSRmpAIEXyPyjEOkqfaYqNUgHQVR+GlT5JxL5M//nrVZDngpKmIZs3pJlT4FF75o
VyC/lufeKqPaAfEaewkw8ZasN9sOtOW4ZSNB9sWsqQ5wWaz40py0E+XzIb8njz3r
EvN8JvSpCRteyIpqXCwskwLLjjCyWKFrh1DglVdQ5UObRdqboZulwl3ll9koDMJO
GT6FFHr/oc8CHFntPcP2dCgtMLlxtK7AH6scy8RaHX8uysJBrpKH5cAvszi2n4je
vIS+h8/U/NhFt1M6QjvtC4+DqK5medWbw5Opd14PHeuNwSWjyrhIkNuoSLb2jXBG
QvfEQ0daXFAJLzzW4jl+EIHUJ0Ad/64NV3jQ2we4ah4d/eApGizdrKSxb+tRF7ma
s6ju0v1DNZWpzqVsoOprC/00h3Fm5OI5CtvzCO/Oi1jYSP+OVnGCmveleXxz+8Tm
z/MPml18ykeSOgwCmh8yvg0oVu7AGjqQ7JlFqErwdiSmW6dgLERcQANxQk1Bme7B
0aE94L/9SvNPElnCvmuQy1NYIMisE9r4+/7s46rQIlKajdke3GFZvTGQzynrVDAQ
C3EzBnflIjqjJsJ8TEslHld69ZzqcPzkxE1jKkNLHLh6Z13o3MXIhE4/93VDtlwG
6CbfV6T0
=Jy/6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
This commits enable (as module):
- STM32 SAI and I2S configs used on stm32mp157.
- Cirrus CS42L51 audio codec for stm32mp157a-dk1 board.
- Audio graph card support for stm32mp157a-dk1 board.
Link: https://lore.kernel.org/r/20191025125632.11057-1-alexandre.torgue@st.com
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove dma-ranges from ltdc node since it is already set
on bus node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Remove dma-ranges from ltdc node since it is already set
on bus node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Active discharge is not needed on vbus_otg and generate unneeded current
consumption.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Minimal value is the value set during boot or before suspend.
We must ensure that the value is a functional value to boot.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of STM32 PWR regulators on
stm32mp157c. This replace dummy fixed regulators on
stm32mp157c-ed1 and stm32mp157c-dk2.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DSI driver doesn't use interrupt, remove it from the node since it
breaks yaml check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c-ed1 board has digital-to-analog converter signals routed
to JP11 and JP10 jumpers (e.g. PA4/PA5).
It's easier then to configure them both. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used by digital-to-analog converter on
stm32mp157c eval daughter board:
- PA4 and PA5 pins are available respectively on JP11 and JP10
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"phy-names" entries are not used. To be compliant with DT validation
tool, those entries have to be remove.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"#size-cells" entry is not needed for "gpio-keys" driver. Indeed "reg"
entry is not used. This commit will fix a warnings seen by DT validation
tool.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
DT validation ("make dtbs_check") has shown that some memory nodes were not
correctly written. This commit fixes this kind of issue:
"stm32f746-disco.dt.yaml: /: memory: False schema does not allow
{'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}"
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure ADC support on stm32mp157a-dk1. It can be used for various
purpose:
- AIN connector has several analog inputs: ANA0, ANA1, ADC2 in6 & in2,
ADC1 in13 & in6
- USB Type-C CC1 & CC2 pins wired to in18 & in19
It's easier then to Configure them all. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Add VDD and VDDA supplies to ADC on stm32mp157c-dk1 board. This allows to
get full ADC analog performances in case VDDA is below 2.7V (not the case
by default).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Define pins that can be used for ADC on stm32mp157a-dk1 board:
- AIN connector has ADC input pins
- USB Type-C CC1 & CC2 pins (e.g. in18, in19)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The ltdc pinctrl must be in the display controller node and
not in the peripheral node (hdmi bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
As of commit 362b334b17 ("ARM: dts: r8a7791: Convert to new
CPG/MSSR bindings"), all upstream R-Car Gen2 device tree source files
use the unified "Renesas Clock Pulse Generator / Module Standby and
Software Reset" DT bindings.
Hence remove backward compatibility with old R-Car Gen2 device trees
describing a hierarchical representation of the various CPG and MSTP
clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191016150939.30620-1-geert+renesas@glider.be
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.
Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device node name should reflect generic class of a device so rename
the "iram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
-----BEGIN PGP SIGNATURE-----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=FUNk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
-----BEGIN PGP SIGNATURE-----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=Gllx
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.5
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
* tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: add DTS for NetCom Plus 4xx and 8xx device series
ARM: dts: add DTS for NetCom Plus 1xx and 2xx device series
ARM: dts: add DTS for NetCAN Plus devices
ARM: dts: omap: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo-37xx-devkit: Increase camera pixel clock
ARM: dts: am: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo: Disable Bluetooth Serial DMA
ARM: dts: IGEP: Add WiLink UART node
ARM: dts: LogicPD Torpedo: Add WiLink UART node
ARM: dts: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel
ARM: dts: logicpd-torpedo-baseboard: Reduce video regulator chatter
ARM: dts: Add minimal support for Droid Bionic xt875
ARM: dts: omap4-droid4: Allow 300mA current for USB peripherals
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes contains SoC related clean-up, and some PM
improvments:
- SoC clean-up to drop unused enable_wakeup and disable_wakeup,
simplify clkdm_clock_enable and disable, and few sparse fixes
- Drop pdata-quirks for TI bluetooth, this is now handled by a serdev
driver
- A series of PM changes to re-enable core oswr (open switch retention)
for omap4 that got disabled earlier because of various gpio-omap issues
that have been fixed earlier this year. We want to do this in small
steps for the pwrdm_set_logic_retst() changes so we can identify the
domain in case of unexpected issues
- A series of PM changes to configure voltage controller for droid4.
Eventually the voltage controller configuration should use device tree,
but we want to get things working first. These changes bring down
down the idle power consumption for droid4 with LCD blanked, WLAN
connected, USB disabled, and modem disabled to about 32 to 35mW from
about 39 to 45 mW
-----BEGIN PGP SIGNATURE-----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=+lr8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
SoC changes for omaps for v5.5
This series of changes contains SoC related clean-up, and some PM
improvments:
- SoC clean-up to drop unused enable_wakeup and disable_wakeup,
simplify clkdm_clock_enable and disable, and few sparse fixes
- Drop pdata-quirks for TI bluetooth, this is now handled by a serdev
driver
- A series of PM changes to re-enable core oswr (open switch retention)
for omap4 that got disabled earlier because of various gpio-omap issues
that have been fixed earlier this year. We want to do this in small
steps for the pwrdm_set_logic_retst() changes so we can identify the
domain in case of unexpected issues
- A series of PM changes to configure voltage controller for droid4.
Eventually the voltage controller configuration should use device tree,
but we want to get things working first. These changes bring down
down the idle power consumption for droid4 with LCD blanked, WLAN
connected, USB disabled, and modem disabled to about 32 to 35mW from
about 39 to 45 mW
* tag 'omap-for-v5.5/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (24 commits)
ARM: OMAP2+: Remove duplicated include from pmic-cpcap.c
ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support
ARM: OMAP2+: make omap44xx_sha0_hwmod and omap44xx_l3_main_2__des static
ARM: OMAP2+: prm44xx: make prm_{save,restore}_context static
ARM: OMAP2+: make dra7xx_sha0_hwmod static
ARM: OMAP2+: do not export am43xx_control functions
ARM: OMAP2+: Configure voltage controller for cpcap to low-speed
ARM: OMAP2+: Configure voltage controller for retention
ARM: OMAP2+: Make some functions static
ARM: OMAP2+: Simplify code for clkdm_clock_enable and disable
ARM: OMAP2+: Drop unused enable_wakeup and disable_wakeup
ARM: OMAP2+: Initialize voltage controller for omap4
ARM: OMAP2+: Allow core oswr for omap4
ARM: OMAP2+: Allow per oswr for omap4
ARM: OMAP2+: Configure voltage controller for cpcap
ARM: OMAP2+: Update 4430 voltage controller operating points
ARM: OMAP2+: Remove bogus warnings for machines without twl PMIC
ARM: OMAP2+: Drop bogus wkup domain oswr setting
ARM: OMAP2+: Remove unused wakeup_cpu
ARM: dts: Use level interrupt for omap4 & 5 wlcore
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
updates for 5.5, please pull the following:
- Stefan adds a machine descriptor for BCM2711 (Raspberry Pi 4) which
sets up the appropriate DMA aperture for the Pi peripherals to work
(1GB window at 3GB offset)
- Ben fixes a number of sparse warnings for the Kona SMC code and the
BCM2836 SMP code
-----BEGIN PGP SIGNATURE-----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=Xijf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.5/soc' of https://github.com/Broadcom/stblinux into arm/soc
This pull request contains Broadcom ARM-based SoCs machine/Kconfig
updates for 5.5, please pull the following:
- Stefan adds a machine descriptor for BCM2711 (Raspberry Pi 4) which
sets up the appropriate DMA aperture for the Pi peripherals to work
(1GB window at 3GB offset)
- Ben fixes a number of sparse warnings for the Kona SMC code and the
BCM2836 SMP code
* tag 'arm-soc/for-5.5/soc' of https://github.com/Broadcom/stblinux:
ARM: bcm: fix missing __iomem in bcm_kona_smc.c
ARM: bcm: include local platsmp.h for bcm2836_smp_ops
ARM: bcm: Add support for BCM2711 SoC
Link: https://lore.kernel.org/r/20191023212814.30622-4-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
-----BEGIN PGP SIGNATURE-----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=CWof
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
* tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: add label to sp805 watchdog
ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
arm64: dts: broadcom: Add reference to RPi 4 B
ARM: dts: Add minimal Raspberry Pi 4 support
dt-bindings: arm: bcm2835: Add Raspberry Pi 4 to DT schema
dt-bindings: arm: Convert BCM2835 board/soc bindings to json-schema
ARM: dts: bcm283x: Move BCM2835/6/7 specific to bcm2835-common.dtsi
ARM: dts: bcm283x: Remove brcm,bcm2835-pl011 compatible
ARM: dts: bcm283x: Remove simple-bus from fixed clocks
Link: https://lore.kernel.org/r/20191023212814.30622-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
A series of changes from Adam Ford to update for removed and moved items,
and then enable crypto devices and MT9P031 video as loadable modules.
Looks like I missed unifying the subject line for one commit, but I did
not want to mess with the commit after pushing it out.
-----BEGIN PGP SIGNATURE-----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=f4PV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/defconfig
Defconfig changes for omap2plus_defconfig for v5.5
A series of changes from Adam Ford to update for removed and moved items,
and then enable crypto devices and MT9P031 video as loadable modules.
Looks like I missed unifying the subject line for one commit, but I did
not want to mess with the commit after pushing it out.
* tag 'omap-for-v5.5/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
configs: omap2plus: Enable VIDEO_MT9P031 module
ARM: omap2plus_defconfig: Enable HW Crypto engine modules
ARM: omap2plus_defconfig: Update for moved item
ARM: omap2plus_defconfig: Update for removed items
Link: https://lore.kernel.org/r/pull-1571853258-16998@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
-----BEGIN PGP SIGNATURE-----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=n/vc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows boards the option of adding properties or disabling the
watchdog entirely.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Two regression fixes for omap3 iommu. I missed applying two omap3
related iommu pdata quirks patches earlier because the kbuild test
robot produced errors on them for missing dependencies.
Fix ti-sysc interconnect target module driver handling for watchdog
quirk. I must have tested this earlier only with watchdog service
running, but clearly it does not do what it needs to do.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl2wgcERHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXN1Vw/+JqxMt2izYIZiVln4uWia37Zypl7yjwFH
6HXgmVPOY0NT17gOYwjX4Fnmvrwe5SsT7obvjPSMCQTNUykffoB2CxiYBMTJ6XPx
5KQMzPT8JCXWBxNNkU+ksHxNjFYhF3s0VIUJX3NGCsCv0YXdjPjWmmZ1udvDvEX1
WDN+YfYrCGWd8TLUGrI4FbWT3eibF1xkVc1y+9jv20gVhsEO1dXYTz5rRjrZAlEE
Le9aG831P4OkncmiUC/bdY2P05l8VXg+fkN3NdOlFwQJRZtHRw23ZyFMPs32SniV
h/3cLuF4hKjE5StgodEhXgQhCvCdShTM9nwAYWDNqCpG+kOHcnI6qpOwJy2WoPNe
JodDqifQgBZc8y7ut37rY9GqssT/VsgKxmhTFdherbadGYpVzF5plVhqqL/yV5OR
KaIVZv/NVsUpXQSGGBoUYe4eZuTIoMTKlm0knN0RE0u+XMRSES5JBZ0f8A4tAc7j
GqKG+zU83D7uJeq3Swa7/TC/8crcZ0W72kMcWpt1xmwJo3K0SFFfyoBdaltzJBxq
pcRNHijfqWdjeDbfL3N/73BeL0Ond8ZnBhl6mlFGsM7NbA9rsMBg3IbYND24+QsV
OmEDWRHW8i+X6MAFhQvHHRGPXblzetENTGpArKTBIyw9JxFLX476XLB8zfQw9Br2
DUq5EREa8CM=
=17ur
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Three fixes for omaps for v5.4-rc cycle
Two regression fixes for omap3 iommu. I missed applying two omap3
related iommu pdata quirks patches earlier because the kbuild test
robot produced errors on them for missing dependencies.
Fix ti-sysc interconnect target module driver handling for watchdog
quirk. I must have tested this earlier only with watchdog service
running, but clearly it does not do what it needs to do.
* tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
Link: https://lore.kernel.org/r/pull-1571848757-282222@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This DTS file covers all four and eight port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers all one and two port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers both NetCAN Plus 110 and 120 WLAN models.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXa/4RQAKCRDj7w1vZxhR
xU3XAQDYuCixpCCftKIhjcz+oultXqAJysDEE44dATwT1YfINgD/eBSwBw1l/Ni7
yOumUvRZ1fJC3NO8e7vh9cYN9yy5tgw=
=3/ru
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe musb with ti-sysc interconnect driver and dts data
with the following changes:
1. Swap the old ti,am33xx-usb compatible wrapper to generic ti-sysc
driver. This means later on we can also remove the old wrapper driver
drivers/usb/musb/musb_am335x.c
2. Update the child nodes to use the ranges provided by ti-sysc
3. Drop unneeded status = "enabled" tinkering for SoC internal devices.
This allows us to remove some useless board specific boilerplate code
in the following patches
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- fix for alignment faults under high memory pressure
- use u32 for ARM instructions in fault handler
- mark functions that must always be inlined with __always_inline
- fix for nommu XIP
- fix ARMv7M switch to handler mode in reboot path
- fix the recently introduced AMBA reset control error paths
-----BEGIN PGP SIGNATURE-----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=EBH5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
:Pull ARM fixes from Russell King:
- fix for alignment faults under high memory pressure
- use u32 for ARM instructions in fault handler
- mark functions that must always be inlined with __always_inline
- fix for nommu XIP
- fix ARMv7M switch to handler mode in reboot path
- fix the recently introduced AMBA reset control error paths
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8926/1: v7m: remove register save to stack before svc
ARM: 8914/1: NOMMU: Fix exc_ret for XIP
ARM: 8908/1: add __always_inline to functions called from __get_user_check()
ARM: mm: alignment: use "u32" for 32-bit instructions
ARM: mm: fix alignment handler faults under memory pressure
drivers/amba: fix reset control error handling
Instead of allowing the Crypto Extensions algorithms to be selected when
using a toolchain that does not support them, and complain about it at
build time, use the information we have about the compiler to prevent
them from being selected in the first place. Users that are stuck with
a GCC version <4.8 are unlikely to care about these routines anyway, and
it cleans up the Makefile considerably.
While at it, add explicit 'armv8-a' CPU specifiers to the code that uses
the 'crypto-neon-fp-armv8' FPU specifier so we don't regress Clang, which
will complain about this in version 10 and later.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a Dell Wyse thin client, variously referred to as "Ariel",
"3020" or "Tx0D" where "x" stands for the software it was shipped with.
I somewhat arbitrarily chose "ariel".
There are bits missing, because the drivers are not in and bindings are not
settled yet:
* Things missing from mmp3.dtsi:
HSIC controller and its PHY (only the internal Ethernet is connected
here, the hub with external USB2 ports is connected to the U2O controller
that works well), Vivante GC2000 GPU
* &twsi1/regulator@19
Marvell 88pm867 power regulator
* &twsi3/vga-dvi-encoder@76
Chrontel CH7033B-BF VGA & DVI encoder
* &twsi3/sound-codec@30
Sound chip, probably a Marvell 88ce156
* &twsi4/embedded-controller@58
ENE KB3930QF Embedded Controller, also seems to be connected to &ssp4.
Might not need a driver -- about the only useful thing it can do is to
reboot the machine when tickled via some GPIO lines.
Also there seems to be something at &twsi1 address 0x50.
Link: https://lore.kernel.org/r/20191022152837.3553524-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
The device node name should reflect generic class of a device so rename
the "ocmcram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default settings used on the baseboard are good for the
OMAP3530 and are compatible with the DM3730. However, the
DM3730 has a faster L3 clock which means the camera pixel clock
can also be pushed faster as well.
This patch increase the Pixel clock to 90MHz which is the
maximum the current ISP driver permits for an L3 clock
of 200MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device node name should reflect generic class of a device so rename
the "ocmcram" node and its children to "sram". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default serial driver for omap2plus is the 8250_omap driver.
Unfortunately, this driver does not yet appear to have fully
functional DMA on OMAP3630/DM3730 which causes some timeouts and
frame errors.
This patch removes the DMA entry from the device tree which allow
the UART to operate without Bluetooth frame errors. If/when DMA
is working on OMAP3630, this should be reverted.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Logic PD Torpedo Development Kit supports a Leopard Imaging
camera based on the Aptina MT9P031 sensor.
This patch enables this to be built as a module.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo ("Initiaize").
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Message-Id: <20191002145301.11332-1-j.neuschaefer@gmx.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All TI_ST users have been migrated to the new serdev based HCILL
bluetooth driver. That driver is initialized from DT and does not
need any platform quirks.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for the UART part of WiLink chip.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for the UART part of WiLink chip.
This is compile tested only!
Cc: Adam Ford <aford173@gmail.com>
Acked-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marvell MMP/PXA/MMP2 platforms seem to be excluded from the defconfig
for no good reasons. Enable the DT-based boards along with modules for
their peripherals.
Link: https://lore.kernel.org/r/20191017145705.2867950-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
This tag includes the MMP3 USB2 PHY driver. The branch is based on
mmp-soc-for-v5.5-2 because the driver depends on changes in MMP SoC
support.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEENyn6vISEy07peidTpxZjkszkJRYFAl2ofwsPHGxrdW5kcmFr
QHYzLnNrAAoJEKcWY5LM5CUWzYsH/iLvSgoDVR+TLxEYQJcpdCCC3tfxBUDYrCvA
hfpf7SuaNHexgrqSl194eoMJ8nmnvcEimGrj3Xgr1iJXge4ECv/fti+aQT1rOUOL
EThqYPDQennCEjfNFBJVAk7mLSHVjrN0d4ItTl11Oxk38rYQFtlq2Z0gNOVU2eJG
n8Orbkwxck2ILDnYfWodPnYAZXa5FOozdp7zOP1sGRztohLTY6JG1vCC++ylM3T3
1HxxwVxGNDzLsgjs/R4A4eSmmHIPQ0BlGi6QCJOcqmXGYelUDPHNnDpo58itC7sQ
D2ClZkEKDqdE4uheknUe+q/gzya6eALqwaBsVVYhBZmLSMBLdgQ=
=3qa/
-----END PGP SIGNATURE-----
Merge tag 'mmp-drivers-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp into arm/drivers
ARM: Marvell MMP driver patches for v5.5
This tag includes the MMP3 USB2 PHY driver. The branch is based on
mmp-soc-for-v5.5-2 because the driver depends on changes in MMP SoC
support.
* tag 'mmp-drivers-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp:
MAINTAINERS: phy: add entry for USB PHY drivers on MMP SoCs
phy: Add USB2 PHY driver for Marvell MMP3 SoC
MAINTAINERS: mmp: add Git repository
ARM: mmp: remove MMP3 USB PHY registers from regs-usb.h
ARM: mmp: move cputype.h to include/linux/soc/
ARM: mmp: add SMP support
ARM: mmp: add support for MMP3 SoC
ARM: mmp: define MMP_CHIPID by the means of CIU_REG()
ARM: mmp: DT: convert timer driver to use TIMER_OF_DECLARE
ARM: mmp: map the PGU as well
ARM: mmp: don't select CACHE_TAUROS2 on all ARCH_MMP
ARM: l2c: add definition for FWA in PL310 aux register
Link: https://lore.kernel.org/r/7cee3ddbb553ba7fe6e1420e0dbc5adb4922b317.camel@v3.sk
Signed-off-by: Olof Johansson <olof@lixom.net>
This tag includes initial support for the Marvell MMP3 processor.
MMP3 is used in OLPC XO-4 laptops, Panasonic Toughpad FZ-A1 tablet
and Dell Wyse 3020/Tx0D thin clients.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEENyn6vISEy07peidTpxZjkszkJRYFAl2ofPMPHGxrdW5kcmFr
QHYzLnNrAAoJEKcWY5LM5CUWcI4H/RlhFZ1Nngu8P19ZPb66GCf27SKgAXvucocN
na6EPBmL+vB0BnlpkXTOtvsOL6riSat/DnUgg4gyCQFVV1SAZdEjnnVAFCEyWSWU
Omc4XDxh6b/geelCElGVCcnomCWvibrkKny1a8bViJdJbVb3lvSou4ZLNNv55uoh
OamyM2yxCgDNQRlvaizfGNbzOCedfCHnFV3eyNx1kMe+OGcSuJe+AZ6Toh045fb9
GWTMeG80AJhWtowcpB5Ivrh31XR3PScOGDOwOlqbyAOao/MalRsBx2Yz+XQ/IceL
RivJ/ImeY/czjFSn2DrsV/nlQDhHP3fjxrtZyUNFV6A8EkHSX0M=
=1Ju7
-----END PGP SIGNATURE-----
Merge tag 'mmp-soc-for-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp into arm/soc
ARM: Marvell MMP SoC patches for v5.5
This tag includes initial support for the Marvell MMP3 processor.
MMP3 is used in OLPC XO-4 laptops, Panasonic Toughpad FZ-A1 tablet
and Dell Wyse 3020/Tx0D thin clients.
* tag 'mmp-soc-for-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp:
MAINTAINERS: mmp: add Git repository
ARM: mmp: remove MMP3 USB PHY registers from regs-usb.h
ARM: mmp: move cputype.h to include/linux/soc/
ARM: mmp: add SMP support
ARM: mmp: add support for MMP3 SoC
ARM: mmp: define MMP_CHIPID by the means of CIU_REG()
ARM: mmp: DT: convert timer driver to use TIMER_OF_DECLARE
ARM: mmp: map the PGU as well
ARM: mmp: don't select CACHE_TAUROS2 on all ARCH_MMP
ARM: l2c: add definition for FWA in PL310 aux register
Link: https://lore.kernel.org/r/3a035bed90f9d8acc49b2d11d20089b546062aea.camel@v3.sk
Signed-off-by: Olof Johansson <olof@lixom.net>
This tag includes binding documentation for various hardware found on Marvell
MMP3 SoC along a DTS file for said hardware.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEENyn6vISEy07peidTpxZjkszkJRYFAl2oekwPHGxrdW5kcmFr
QHYzLnNrAAoJEKcWY5LM5CUWLjgH/3u758cDz/ad1gdtTN/oIQtrHHwR2AmgCG5M
tO0+EYAPOsRAUDpPZF/aoFXoP3NJ2dUgHcj+hYX5S0ZuE4ijOJwSKiYZbXd9QX0+
e4iUh77CdtoTv+y6W6GjkFMnnjIfiCSm+Tby4jc9Ty/+ImBGGYSnS2fnxmyFfEBZ
eDtPZSGJJmmTJNt9UMaWaRC0sivSStzBPiwqVE/aG75askc/Fd3OOIcA9Bm8ot1E
i3T7i/PRw4q/mOgrXMvqs7BSTsgVnBOCxTClKIT6PuT9ZxkRUwWp9QTvEd/nVLs9
DrROFCaVKLXx7HHi+5CbjP88F0w61CBQXntFGMGkxx0iG6Evo8U=
=l10O
-----END PGP SIGNATURE-----
Merge tag 'mmp-dt-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp into arm/dt
ARM: Marvell MMP Device Tree patches for v5.5
This tag includes binding documentation for various hardware found on Marvell
MMP3 SoC along a DTS file for said hardware.
* tag 'mmp-dt-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp:
ARM: dts: mmp3: Add MMP3 SoC dts file
dt-bindings: phy-mmp3-usb: Add bindings
dt-bindings: mrvl,intc: Add a MMP3 interrupt controller
dt-bindings: arm: mrvl: Document MMP3 compatible string
dt-bindings: arm: Convert Marvell MMP board/soc bindings to json-schema
dt-bindings: arm: cpu: Add Marvell MMP3 SMP enable method
Link: https://lore.kernel.org/r/d4897c4a92319527c46147244282803cd9f5a1ff.camel@v3.sk
Signed-off-by: Olof Johansson <olof@lixom.net>
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
-----BEGIN PGP SIGNATURE-----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=uqu5
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS changes for DMC driver for v5.5
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
* tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: memory-controllers: exynos5422-dmc: Correct example syntax and memory region
ARM: dts: exynos: Add interrupts to DMC controller in Exynos5422
ARM: dts: exynos: Extend mapped region for DMC on Exynos5422
dt-bindings: memory-controllers: exynos5422-dmc: Add interrupt mode
dt-bindings: ddr: Add bindings for Samsung LPDDR3 memories
ARM: dts: exynos: Add DMC device to Exynos5422 and Odroid XU3-family boards
ARM: dts: exynos: Add syscon compatible to clock controller on Exynos542x
dt-bindings: memory-controllers: Add Exynos5422 DMC device description
dt-bindings: ddr: Add bindings for LPDDR3 memories
dt-bindings: ddr: Rename lpddr2 directory
Link: https://lore.kernel.org/r/20191021180453.29455-6-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add ARM architected timers on Exynos5 for KVM-based virtualization,
2. Extend chip identification needed for future Adaptive Supply Voltage,
3. Add audio support to Arndale board,
4. Fix init order of clock providers on s3c64xx,
5. A lot of cleanups and adjustments of DTS with DT schema.
-----BEGIN PGP SIGNATURE-----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=Ri1S
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.5
1. Add ARM architected timers on Exynos5 for KVM-based virtualization,
2. Extend chip identification needed for future Adaptive Supply Voltage,
3. Add audio support to Arndale board,
4. Fix init order of clock providers on s3c64xx,
5. A lot of cleanups and adjustments of DTS with DT schema.
* tag 'samsung-dt-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Fix init order of clock providers
ARM: dts: exynos: Rename SysRAM node to "sram"
ARM: dts: exynos: Rename power domain nodes to "power-domain" in Exynos4
ARM: dts: exynos: Add audio support (WM1811 CODEC boards) to Arndale board
ARM: dts: exynos: Use defines for MCT interrupt GIC SPI/PPI specifier
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos54xx
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos5250
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4412
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4210
ARM: dts: exynos: Rename Multi Core Timer node to "timer"
ARM: dts: exynos: Split phandle in dmas property
ARM: dts: exynos: Remove obsolete IRQ lines on Exynos3250
ARM: dts: exynos: Add samsung,asv-bin property to Odroid XU3 Lite
ARM: dts: exynos: Add "syscon" compatible string to chipid node on Exynos5
ARM: dts: exynos: Add support ARM architected timers on Exynos5
Link: https://lore.kernel.org/r/20191021180453.29455-4-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
the cpuid found in the efuses. Veyron display got a cleanup to use the
interpolated backlight values instead of declaring huge tables
and finally a cleanup fixing some tabs/spaces issues in the dts files.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl2tnOcQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgW+GCACYHiRGotnJibFu4gCerBoISP13qzqQnpYR
VSYnR84pD/cOzDas8PKOkPUg9+Db5fsDN1NPAp/S0vyirye5jgjQFlWNK7+o04Qr
JnLJYv1OlhkRiipuTJesiMo4mIOpiJWvliU050pmfzTJihZwBocw9FUqllq/V14A
WwNhcGIhZxEB+GkKkpFj7PZXSkTQy3PwmWZEAL2C9U2qHL4Vszlmo1P0AAx9af0S
8FCY1OhVSZ/C732k/aijmg7tm70uBwKeBz1Kn/Rh/AiI34yzUufxnPojQstlLkRt
pJnTypt0nc/1Gxt16So/4HjTfuIdT2pK6Q9t71VNbQl/3ogKE2Oj
=r5X+
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New rk3288 features are Gamma support for the VOPs as well as declaring
the cpuid found in the efuses. Veyron display got a cleanup to use the
interpolated backlight values instead of declaring huge tables
and finally a cleanup fixing some tabs/spaces issues in the dts files.
* tag 'v5.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove some tabs and spaces from dtsi files
ARM: dts: rockchip: Add RK3288 VOP gamma LUT address
ARM: dts: rockchip: Use interpolated brightness tables for veyron
ARM: dts: rockchip: Add cpu id to rk3288 efuse node
Link: https://lore.kernel.org/r/1770986.Em1ahGqaF7@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
-----BEGIN PGP SIGNATURE-----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=BwM0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
* tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
Link: https://lore.kernel.org/r/20191021194302.21024-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
