Tc chains are implemented by creating a chained prio steering type, and
inside it there is a namespace for each chain (FDB_TC_MAX_CHAINS). Each
of those has a list of priorities.
Currently, all namespaces in a prio start at the parent prio level.
But since we can jump from chain (namespace) to another chain in the
same prio, we need the levels for higher chains to be higher as well.
So we created unused prios to account for levels in previous namespaces.
Fix that by accumulating the namespaces levels if we are inside a chained
type prio, and removing the unused prios.
Fixes: 328edb499f ('net/mlx5: Split FDB fast path prio to multiple namespaces')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Define FDB_TC_LEVELS_PER_PRIO instead of magic number 2.
This is the number of levels used by each tc prio table in the fdb.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename it to prepare for next patch that will add a
different type of offload to the FDB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
FDB_MAX_CHAIN and FDB_MAX_PRIO were defined differently depending
on if CONFIG_MLX5_ESWITCH is enabled to save space on allocations.
This is a minor space saving, and there is no real need for it.
Simplify things instead, and define them the same in both cases.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is a return statement that is indented too deeply, remove
the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the MACB Ethernet driver to the Phylink framework.
The MAC configuration is moved to the Phylink ops and Phylink helpers
are now used in the ethtools functions. This helps to access the flow
control and pauseparam logic and this will be helpful in the future for
boards using this controller with SFP cages.
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the Tx and Rx buffer initialization into its own
function. This does not modify the behaviour of the driver and will be
helpful to convert the driver to phylink.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable xilinx axi_emac driver support on zynqmp ultrascale platform
(ARCH64) there are two choices, mention ARCH64 as a dependency list
and other is to check if this ARCH dependency list is really needed.
Later approach seems more reasonable, so remove the obsolete ARCH
dependency list for the axi_emac driver.
Sanity test done for microblaze, zynq and zynqmp ultrascale platform.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing support for the PHY mode RGMII_RXID.
It's necessary for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register access in bcmgenet_mii_config() is a little bit opaque and
not easy to extend. In preparation for the missing RGMII PHY modes
move all the phy name assignments into the switch statement and the
register access to the end of the function. This make the code easier
to read and extend.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM2711 needs a different maximum DMA burst length. If not set
accordingly a timeout in the transmit queue happens and no package
can be sent. So use the new compatible to derive this value.
Until now the GENET HW version was used as the platform identifier.
This doesn't work with SoC-specific modifications, so introduce a proper
platform data structure.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the error handling for the mandatory IRQs. There is no need
for the error message anymore, this is now handled by platform_get_irq.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As platform_get_irq() now prints an error when the interrupt does not
exist, we are getting a confusing error message in case the optional
WOL IRQ is not defined:
bcmgenet fd58000.ethernet: IRQ index 2 not found
Fix this by using the platform_get_irq_optional().
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfc driver can drop packets processed with XDP, notably when running
out of buffer space on XDP_TX, or returning an unknown XDP action.
This increments the rx_xdp_bad_drops ethtool counter.
Call trace_xdp_exception everywhere rx_xdp_bad_drops is incremented,
except for fragmented RX packets as the XDP program hasn't run yet.
This allows it to easily be monitored from userspace.
This mirrors the behavior of other drivers.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant code from fw_fatal reporter's dump callback. Use
updated devlink interface of binary fmsg pair which breaks the output
into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c:242:6: warning: symbol 'cxgb4_mqprio_free_hw_resources' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:706:5: warning: symbol 'aq_ethtool_get_priv_flags' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:713:5: warning: symbol 'aq_ethtool_set_priv_flags' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:426:25: warning: symbol 'aq_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to enable EMAD string TLV only after using the required firmware
version.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the firmware had an error while processing EMADs, it can send back
an ASCII string with the reason using EMAD string TLV.
This patch adds the support for using EMAD string TLV. In case of an error,
reports the reason using devlink hwerr tracepoint.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend EMAD information reported to devlink hwerr tracepoint with
transaction id and reg id (both, hex and string).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During parsing of incoming EMADs, fill the string TLV's offset when it is
used.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EMAD string TLV, an ASCII string the driver can receive from the
firmware in case of an error.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the code assumes a fixed structure which makes it difficult to
support EMADs with and without new TLVs.
Make it more generic by parsing the TLVs when the EMADs are received and
store the offset to the different TLVs in the control block. Using these
offsets to extract information from the EMADs without relying on a specific
structure.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TI_DAVINCI_EMAC=y and GENERIC_ALLOCATOR is not set,
below erros can be seen:
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.14':
davinci_cpdma.c:(.text+0x359): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x365): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x373): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x37f): undefined reference to `gen_pool_size'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x4a2): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit_si':
davinci_cpdma.c:(.text+0x66c): undefined reference to `gen_pool_alloc_algo_owner'
davinci_cpdma.c:(.text+0x805): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
davinci_cpdma.c:(.text+0xabd): undefined reference to `devm_gen_pool_create'
davinci_cpdma.c:(.text+0xb79): undefined reference to `gen_pool_add_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
davinci_cpdma.c:(.text+0x16c6): undefined reference to `gen_pool_avail'
This patch mades TI_DAVINCI_EMAC select GENERIC_ALLOCATOR.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the UDP Segmentation Offload feature in stmmac. This is only
available in GMAC4+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks over-engineered. Let's use some helpers to get the buffer
length and hereby simplify the stmmac_rx() function. No performance drop
was seen with the new implementation.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.
v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VID is converted to le16 so the variable must be __le16 type.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254b ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC7514 is a 10-port switch with 2 extra "CPU ports" (targets in the
queuing subsystem for terminating traffic locally).
There are 2 issues with hardcoding the CPU port as #10:
- It is not clear which snippets of the code are configuring something
for one of the CPU ports, and which snippets are just doing something
related to the number of physical ports.
- Actually any physical port can act as a CPU port connected to an
external CPU (in addition to the local CPU). This is called NPI mode
(Node Processor Interface) and is the way that the 6-port VSC9959
(Felix) switch is integrated inside NXP LS1028A (the "local management
CPU" functionality is not used there).
This patch makes it clear that the ocelot_bridge_stp_state_set function
operates on the CPU port (by making it an implicit member of the
bridging domain), and at the same time adds logic for the NPI port (aka
a physical port) to play the role of a CPU port (it shouldn't be part of
bridge_fwd_mask, as it's not explicitly enslaved to a bridge).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the places that configure routing destinations for the CPU port
have been marked as such, allow callers to specify their own CPU port
that is different than ocelot->num_phys_ports. A user will be the Felix
DSA driver, where the CPU port is one of the physical ports (NPI mode).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be called from the Felix DSA frontend, which will work in
PHYLIB compatibility mode initially.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just common path code that belongs to ocelot_init,
it has nothing to do with a specific SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow these functions to be called from the .port_enable and
.port_disable callbacks of DSA.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a function for the DSA front-end that does none of the
net_device registration, but initializes the hardware ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 switch (Ocelot) is a 10-port device, while VSC9959 (Felix)
is 6-port. Therefore the VLAN filtering mask would be out of bounds when
calling for this new switch. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert them into an implementation that can be called from DSA as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot and ocelot_port structures will be used by a new DSA driver,
so the ocelot_board.c file will have to allocate and work with a private
structure (ocelot_port_private), which embeds the generic struct
ocelot_port. This is because in DSA, at least one interface does not
have a net_device, and the DSA driver API does not interact with that
anyway.
The ocelot_port structure is equivalent to dsa_port, and ocelot to
dsa_switch. The members of ocelot_port which have an equivalent in
dsa_port (such as dp->vlan_filtering) have been moved to
ocelot_port_private.
We want to enforce the coding convention that "ocelot_port" refers to
the structure, and "port" refers to the integer index. One can retrieve
the structure at any time from ocelot->ports[port].
The patch is large but only contains variable renaming and mechanical
movement of fields from one structure to another.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port structure has a net_device embedded in it, which makes
it unsuitable for leaving it in the driver implementation functions.
Leave ocelot_flower.c untouched. In that file, ocelot_port is used as an
interface to the tc shared blocks. That will be addressed in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the Felix DSA front-end can call the Ocelot
implementations.
The implementation of the "mc_disabled" switchdev attribute has also
been simplified by using the read-modify-write macro instead of
open-coding that operation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in order to present a simpler prototype to the DSA
front-end of ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to implement a DSA front-end over ocelot_fdb_add,
ocelot_fdb_del, ocelot_fdb_dump, these need to have a simple function
prototype that is independent of struct net_device, netlink skb, etc.
So rename the ndo ops of the ocelot driver into
ocelot_port_fdb_{add,del,dump}, and have them all call the abstract
implementations. At the same time, refactor ocelot_port_fdb_do_dump into
a function whose prototype is compatible with dsa_fdb_dump_cb_t, so that
the do_dump implementations can live together and be called by the
ocelot_fdb_dump through a function pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need an implementation of these functions that is agnostic to the
higher layer (switchdev or dsa).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch transforms the ocelot_vlan_port_apply function ("apply
what?") into 3 standalone functions:
- ocelot_port_vlan_filtering
- ocelot_port_set_native_vlan
- ocelot_port_set_pvid
These functions have a prototype that is better aligned to the DSA API.
The function also had some static initialization (TPID, drop frames with
multicast source MAC) which was not being changed from any place, so
that was just moved to ocelot_probe_port (one of the 6 callers of
ocelot_vlan_port_apply).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.
The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output
The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register "enable_roce" param, default value is RoCE enabled.
Current configuration is stored on mlx5_core_dev and exposed to user
through the cmode runtime devlink param.
Changing configuration requires changing the cmode driverinit devlink
param and calling devlink reload.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-08
Another series that contains updates to the ice driver only.
Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration. Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.
Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.
Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.
Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.
Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.
Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.
Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.
Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF. Updates a flag bit
to align with the current specification.
Bruce updates a switch statement to use the correct status of the
Download Package AQ command. Does some housekeeping by cleaning up a
conditional check that is not needed.
Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.
Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in. Improve debugging by adding the command opcode in the debug
messages that print an error code.
v2: fixed reverse christmas tree issue in patch 3 of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU can be a frequent operation and it is already clear
when (or not) a MTU change is successful, demote prints to debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.
Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update on more short variant for getting real clock in ns.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia is now part of Marvell, eventually we'll cease standalone
aquantia.com domain. Thus, change the maintainers file and some other
references to @marvell.com domain
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atlantic hardware does support UDP hardware segmentation offload.
This allows user to specify one large contiguous buffer with data
which then will be split automagically into multiple UDP packets
of specified size.
Bulk sending of large UDP streams lowers CPU usage and increases
bandwidth.
We did estimations both with udpgso_bench_tx test tool and with modified
iperf3 measurement tool (4 streams, multithread, 200b packet size)
over AQC<->AQC 10G link. Flow control is disabled to prevent RX side
impact on measurements.
No UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 200 -P4 --multithread
UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 12600 --udp-lso 200 -P4 --multithread
Mode CPU iperf speed Line speed Packets per second
-------------------------------------------------------------
NO UDP GSO 350% 3.07 Gbps 3.8 Gbps 1,919,419
SW UDP GSO 200% 5.55 Gbps 6.4 Gbps 3,286,144
HW UDP GSO 90% 6.80 Gbps 8.4 Gbps 4,273,117
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now differentiate requested and negotiated flow control
modes. Therefore `ethtool -A` now operates on local requested
FC values, and regular link settings shows the negotiated FC
settings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to follow the naming of the chip (atlantic), not
company. So replace some old namings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats a pure checkpatck walkthrough the code with no functional
changes. Reverse christmas tree, spacing, etc.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add a number of ethtool private flags
to allow enabling various loopbacks on HW.
Thats useful for verification and bringup works.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device FW has a separate memory area where various
config fields are stored and could be used by the
driver.
Here we modify download/upload infrastructure to
allow accessing this area.
Lateron this will be used to configure various behaviours
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ethtool -p eth0` will blink leds helping identify
physical port.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add ethtool msglevel configuration and change some
printouts to use netdev_info set of functions.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now implement .driver.pm callbacks, these
allows driver to work correctly in hibernate
usecases, especially when used in conjunction with
WOL feature.
Before that driver only reacted to legacy .suspend/.resume
callbacks, that was a limitation in some cases.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake on PHY allows to configure device to wakeup host
as soon as PHY link status is changed to active.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we improve FW interface structures layout
and prepare these for the wake phy feature implementation.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs used to report layer 3 exceptions.
Trapped packets are first reported to devlink and then injected to the
kernel's receive path. All the packets have 'offload_fwd_mark' set in
order to prevent them from potentially being forwarded by the bridge
again.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw does not differentiate between these two cases of
routes with invalid nexthops:
1. Nexthops whose nexthop device is a mlxsw upper (has a RIF), but whose
neighbour could not be resolved
2. Nexthops whose nexthop device is not a mlxsw upper (e.g., management
interface)
Up until now this did not matter and mlxsw trapped packets for both
cases using the same trap ID. However, packets that should have been
routed in hardware (case 1), but incurred a problem are considered
exceptions and should be reported to the user. The two cases should
therefore be split between two different trap IDs.
Allocate a new adjacency entry during initialization and upon the
insertion of the first route with an invalid mlxsw nexthop, program this
entry to discard packets. Packets hitting this entry will be reported
using new trap ID - "DISCARD_ROUTER3".
In the future, the entry could be written during initialization, but
currently firmware requires a valid RIF, which is not available at this
stage.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, packets that cannot be routed in hardware (e.g., nexthop
device is not upper of mlxsw), are trapped to the kernel for forwarding.
Such packets are trapped using "RTR_INGRESS0" trap. This trap also traps
packets that hit reject routes (e.g., "unreachable") so that the kernel
will generate the appropriate ICMP error message for them.
Subsequent patch will need to only report to devlink packets that hit a
reject route, which is impossible as long as "RTR_INGRESS0" is
overloaded like that.
Solve this by using "RTR_INGRESS1" trap for packets that hit reject
routes.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs and trap group used to report layer 3 drops. Register
layer 3 packet traps and associated layer 3 trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EOPNOTSUPP instead of -EINVAL if the requested ioctl is not
implemented.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
[1] https://git.kernel.org/torvalds/c/4bd2c03be7
[2] https://patchwork.ozlabs.org/patch/1189139/
Fixes: 4bd2c03be7 ("net: hns: remove ndo_poll_controller")
Cc: lipeng <lipeng321@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DPNI is connected to a MAC, export its associated counters.
Ethtool related functions are added in dpaa2_mac for returning the
number of counters, their strings and also their values.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an external PHY, pass the wake-on-lan request to the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an attached PHY try to handle the requested ioctl with its
handler, which allows the userspace to access PHY registers, for
example. This will make mii-diag and similar tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 4a7f970f12 ("mlxsw: spectrum: Replace port_to_module array with array of structs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework SCHED API to allow offloading TC-MQPRIO QoS configuration.
The existing QUEUE based rate limiting throttles all queues sharing
a traffic class, to the specified max rate limit value. So, if
multiple queues share a traffic class, then all the queues get
the aggregate specified max rate limit.
So, introduce the new FLOWC based rate limiting, where multiple
queues can share a traffic class with each queue getting its own
individual specified max rate limit.
For example, if 2 queues are bound to class 0, which is rate limited
to 1 Gbps, then 2 queues using QUEUE based rate limiting, get the
aggregate output of 1 Gbps only. In FLOWC based rate limiting, each
queue gets its own output of max 1 Gbps each; i.e. 2 queues * 1 Gbps
rate limit = 2 Gbps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement Tx path for traffic flowing through software EOSW_TXQ
and EOHW_TXQ. Since multiple EOSW_TXQ can post packets to a single
EOHW_TXQ, protect the hardware queue with necessary spinlock. Also,
move common code used to generate TSO work request to a common
function.
Implement Rx path to handle Tx completions for successfully
transmitted packets.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring and managing ETHOFLD hardware queues.
Keep the queue count and MSI-X allocation scheme same as NIC queues.
ETHOFLD hardware queues are dynamically allocated/destroyed as
TC-MQPRIO Qdisc offload is enabled/disabled on the corresponding
interface, respectively.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for validation and configuration of TC-MQPRIO Qdisc
offload. Also, add support to manage EOSW_TXQ, which have 1-to-1
mapping with EOTIDs, and expose them to network stack.
Move common skb validation in Tx path to a separate function and
add minimal Tx path for ETHOFLD. Update Tx queue selection to return
normal NIC Txq to send traffic pattern that can't go through ETHOFLD
Tx path.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify queue configuration and MSI-X allocation logic. Use a single
MSI-X information table for both NIC and ULDs. Remove hard-coded
MSI-X indices for firmware event queue and non data interrupts.
Instead, use the MSI-X bitmap to obtain a free MSI-X index
dynamically. Save each Rxq's index into the MSI-X information table,
within the Rxq structures themselves, for easier cleanup.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QoS offload needs Ethernet Offload (ETHOFLD) resources present in the
NIC. These resources are shared with other ULDs. So, query firmware
for the available number of traffic classes, as well as, start and
end indices (EOTID) of the ETHOFLD region.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb0799 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-06
This series contains updates to ice driver only.
Scott adds ethtool -m support so that we can read eeprom data on SFP/OSFP
modules.
Anirudh updates the return value to properly reflect when SRIOV is not
supported.
Md Fahad updates the driver to handle a change in the NVM, where the
boot configuration section was moved to the Preserved Field Area (PFA)
of the NVM.
Paul resolves an issue when DCBx requests non-contiguous TCs, transmit
hangs could occur, so configure a default traffic class (TC0) in these
cases to prevent traffic hangs. Adds a print statement to notify the
user when unsupported modules are inserted.
Bruce fixes up the driver unload code flow to ensure we do not clear the
interrupt scheme until the reset is complete, otherwise a hardware error
may occur.
Dave updates the DCB initialization to set is_sw_lldp boolean when the
firmware has been detected to be in an untenable state. This will
ensure that the firmware is in a known state.
Michal saves off the PCI state and I/O BARs address after PCI bus reset
so that after the reset, device registers can be read. Also adds a NULL
pointer check to prevent a potential kernel panic.
Mitch resolves an issue where VF's on PF's other than 0 were not seeing
resets by using the per-PF VF ID instead of the absolute VF ID.
Krzysztof does some code cleanup to remove a unneeded wrapper and
reduces the code complexity.
Brett reduces confusion by changing the name of ice_vc_dis_vf() to
ice_vc_reset_vf() to better describe what the function is actually
doing.
v2: dropped patch 3 "ice: Add support for FW recovery mode detection"
from the origin al series, while Ani makes changes based on
community feedback to implement devlink into the changes.
v3: dropped patch 1 "ice: implement set_eeprom functionality" due to a
bug found and additional changes will be needed when Ani implements
devlink in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl3DQ0sACgkQSD+KveBX
+j4nKgf/XnUZGR4PHGcEfalc/p67J7jmi7SN5Xuts8uyUTgqMGni/SkWRl+S1mQy
8dl5kZK/JxBhAzzlVIcXpcmkfeXydcrm1NHMPCOMsnUrAWAEP0lE1lfLBkX1zWPi
OHb3+nziJHc0s4AI/Haca7JOj8HjBSOPpv3Udg6f53leizo31pK2FSiBASc5bRoX
EUNMD3eFAap7fjBMVLzO/JeQXxgjaqb9qU3AKopy34cg+AInZ+ZH2S++aoT7RG3J
MCPOnrSxLmhA4BUu5I81vfgFNxxPP65vI7NPIhSMY7+pOQJNPIc1p08XvIpQ9X2o
5o/rQ9tVxq2NZqcMB+b6tiHVFYu7Kw==
=OmLZ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-11-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahamees says:
====================
Mellanox, mlx5 fixes 2019-11-06
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
No -stable this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d2864 ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.
Fixes: b6cdf09f51 ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.
Fixes: ec6ea8e3ee ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.
Fixes: c2b69474d6 ("net: stmmac: xgmac: Correct RAVSEL field interpretation")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.
Fixes: ec6ea8e3ee ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.
To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 0efedbf11f ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function ptp_clock_register() returns ERR_PTR() and never returns
NULL. The NULL test should be removed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is not capable of supporting SR-IOV -ENODEV is being
returned; -EOPNOTSUPP is more appropriate.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vc_dis_vf() tells iavf that it's going to perform a reset
and then performs a software reset. This is misleading based on
the function name because the VF does not get disabled. So fix
this by changing the name to ice_vc_reset_vf().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_cleanup_hdrs() has been stripped of most of its content, it only serves
as a wrapper for eth_skb_pad(). We can get rid of it altogether and
simplify the codebase.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print message to inform user of PCI link speed and width.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print message to inform user if unsupported module is inserted, and
extend the topology / configuration detection.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.
This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust ice_init_dcb to set the is_sw_lldp boolean
in the case where the FW has been detected to be
in an untenable state such that the driver
should forcibly make sure it is off.
This will ensure that the FW is in a known state.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device. Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCBx request non-contiguous TCs, then the driver will configure default
traffic class (TC0). This is done to prevent Tx hang since the driver
currently does not support non-contiguous TC.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Boot Configuration Section Block has been moved to the Preserved Field
Area (PFA) of NVM. Update the NVM reads that involves Boot Configuration
Section.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lag_upper_info may be NULL on slave removal.
Fixes: dc96ee3730 ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730 ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For vlan push action, if eswitch flow source capability is enabled, flow
source value compared with MLX5_VPORT_UPLINK enum, to determine uplink
port. This lead to syndrome in dmesg if try to add vlan push action.
For example:
$ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \
enc_dst_port 4789 \
action tunnel_key unset pipe \
action vlan push id 20 pipe \
action mirred egress redirect dev ens1f0_0
$ dmesg
...
[ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090)
Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK.
Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The rewrite data was no freed.
Fixes: 9db810ed2d ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The value is already the calculation so remove the log prefix.
Fixes: e52c280240 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f51548627.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function page_shift() is supported after the commit 94ad933810
("mm: introduce page_shift()").
So replace with page_shift() in ehea_is_hugepage() for readability.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for xmit_more based on the igb commit 6f19e12f62
("igb: flush when in xmit_more mode and under descriptor pressure") and
commit 6b16f9ee89 ("net: move skb->xmit_more hint to softnet data") that
were made to igb to support this feature. The function netif_xmit_stopped
is called to check whether transmit queue on device is currently unable to
send to determine whether we must write the tail because we can add no
further buffers.
When normal packets and/or xmit_more packets fill up tx_desc, it is
necessary to trigger NIC tx reg.
Following the advice from David Miller and Jakub Kicinski, after the
xmit_more feature is added, the following scenario will occur.
|
xmit_more packets
|
DMA_MAPPING
|
DMA_MAPPING error check
|
xmit_more packets already in HW xmit queue
|
In the above scenario, if DMA_MAPPING error occurrs, the xmit_more packets
already in HW xmit queue will also be dropped. This is different from the
behavior before xmit_more feature. So it is necessary to trigger NIC HW tx
reg in the above scenario.
To the non-xmit_more packets, the above scenario will not occur.
Tested:
- pktgen (xmit_more packets) SMP x86_64 ->
Test command:
./pktgen_sample03_burst_single_flow.sh ... -b 8 -n 1000000
Test results:
Params:
...
burst: 8
...
Result: OK: 12194004(c12188996+d5007) usec, 1000001 (1500byte,0frags)
82007pps 984Mb/sec (984084000bps) errors: 0
- iperf (normal packets) SMP x86_64 ->
Test command:
Server: iperf -s
Client: iperf -c serverip
Result:
TCP window size: 85.0 KByte (default)
------------------------------------------------------------
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 1.10 GBytes 942 Mbits/sec
CC: Joe Jin <joe.jin@oracle.com>
CC: JUNXIAO_BI <junxiao.bi@oracle.com>
Reported-and-tested-by: Nan san <nan.1986san@gmail.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a esw_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently when a call to esw_vport_create_legacy_ingress_acl_group
fails the error exit path to label 'out' will cause a kvfree on the
uninitialized pointer spec. Fix this by ensuring pointer spec is
initialized to NULL to avoid this issue.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 10652f3994 ("net/mlx5: Refactor ingress acl configuration")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.
Fixes: d1f0b5dce8 ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a phy_interface_t to of_get_phy_mode(), by changing the type of
phy_mode in the device structure. This then requires that
zmii_attach() is also changes, since it takes a pointer to phy_mode.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used. I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the pre-allocation of one CQE is to enable resizing of
the CQ.
Fix comment accordingly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains updates to the ice driver only.
Anirudh refactors the code to reduce the kernel configuration flags and
introduces ice_base.c file.
Maciej does additional refactoring on the configuring of transmit
rings so that we are not configuring per each traffic class flow.
Added support for XDP in the ice driver. Provides additional
re-organizing of the code in preparation for adding build_skb() support
in the driver. Adjusted the computational padding logic for headroom
and tailroom to better support build_skb(), which also aligns with the
logic in other Intel LAN drivers. Added build_skb support and make use
of the XDP's data_meta.
Krzysztof refactors the driver to prepare for AF_XDP support in the
driver and then adds support for AF_XDP.
v2: Updated patch 3 of the series based on community feedback with the
following changes...
- return -EOPNOTSUPP instead of ENOTSUPP for too large MTU which makes
it impossible to attach XDP prog
- don't check for case when there's no XDP prog currently on interface
and ice_xdp() is called with NULL bpf_prog; this happens when user
does "ip link set eth0 xdp off" and no prog is present on VSI; no need
for that as it is handled by higher layer
- drop the extack message for unknown xdp->command
- use the smp_processor_id() for accessing the XDP Tx ring for XDP_TX
action
- don't leave the interface in downed state in case of any failure
during the XDP Tx resources handling
- undo rename of ice_build_ctob
The above changes caused a ripple effect in patches 4 & 5 to update
references to ice_build_ctob() which are now build_ctob()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains old Halloween candy updates, yet still sweet, to
fm10k, ixgbe and i40e.
Jake adds the missing initializers for a couple of the TLV attribute
macros. Added support for capturing and reporting statistics for all of
the VFs in a given PF. Lastly, bump the version of the fm10k driver to
reflect the recent changes.
Alex addresses locality issues in the ixgbe driver when it is loaded on
a system supporting multiple NUMA nodes.
Manjunath Patil provides changes to the ixgbe driver, similar to those
made to igb, to prevent transmit packets to request a hardware timestamp
when the NIC has not been setup via the SIOCSHWTSTAMP ioctl.
Alice adds support for x710 by adding the missing device id's in the
appropriate places to ensure all the features are enabled in i40e.
Jesse adds support for VF stats gathering in the i40e via the kernel
via ndo_get_vf_stats function.
v2: Fixed up commit id references in patch 5's description to align with
how commit id's should be referenced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>
Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
RX: bytes packets mcast bcast
128000 1000 104 104
TX: bytes packets
128000 1000
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places. Adding it
to enable it's use.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Similar-to:
commit 26bd4e2db0 ("igb: protect TX timestamping from API misuse")
commit 0a6f2f05a2 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.
The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.
In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.
I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.
Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.
In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.
This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;
With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.
In the followup patch the headroom/tailroom computation logic will be
introduced.
This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.
For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.
For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c. This allows us to
avoid using ifdefs to control the staticness of said functions.
Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with W=1 (cf.scripts/Makefile.extrawarn) outputs:
warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Drop the unused 'ret' variable.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOC3 hardware needs a 16k aligned TX ring.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set NETIF_F_HIGHDMA together with the NETIF_F_IP_CSUM flag instead of
letting the second assignment overwrite it. Probably doesn't matter
in practice as none of the systems an IOC3 is usually found in has
highmem to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to fall back to a lower mask these days, the DMA mask
just communicates the hardware supported features.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_alloc_coherent always zeroes memory, there is no need for
__GFP_ZERO. Also doing a GFP_ATOMIC allocation just before a GFP_KERNEL
one is clearly bogus.
Fixes: ed870f6a7a ("net: sgi: ioc3-eth: use dma-direct for dma allocations")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_direct_ is a low-level API that must never be used by drivers
directly. Switch to use the proper DMA API instead.
Fixes: ed870f6a7a ("net: sgi: ioc3-eth: use dma-direct for dma allocations")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit. Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no reason for treating DCB as first class citizen when configuring
the Tx queues and going through TCs. Reverse the logic and base the
configuration logic on rings, which is the object of interest anyway.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [0] at least one RTL8168dp version has problems
establishing a link. This chip version has an integrated RTL8211b PHY,
however the chip seems to report a wrong PHY ID, resulting in a wrong
PHY driver (for Generic Realtek PHY) being loaded.
Work around this issue by adding a hook to r8168dp_2_mdio_read()
for returning the correct PHY ID.
[0] https://bbs.archlinux.org/viewtopic.php?id=246508
Fixes: 242cd9b586 ("r8169: use phy_resume/phy_suspend")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synces the DMA buffer properly in order for CPU and device to see
the most up-to-data data.
Signed-off-by: Yangchun Fu <yangchun@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now SW steering supported matchers that are IPv4 and IPv6.
The limitation was mixed matchers in which the outer header IP version
was different from the inner header IP version.
To support the mixed matcher we create all the possible ste_builder
combinations, once we create a rule we select the correct one to
be used for rule creation.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of using explicit indexes, simply use affinity
type enumerators to make the code more readable.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of using explicit array indexes, simply use
ports enumerators to make the code more readable.
Fixes: 7907f23adc ("net/mlx5: Implement RoCE LAG feature")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
when debug a bug, which triggers TX hang, and kernel log is
spammed with the following info message
[ 1172.044764] mlx5_core 0000:21:00.0: cmd_work_handler:930:(pid 8):
failed to allocate command entry
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for rewriting of DSCP part of ToS field.
Next commands, for example, can be used to offload rewrite action:
OVS:
$ ovs-ofctl add-flow ovs-sriov "ip, in_port=REP, \
actions=mod_nw_tos:68, output:NIC"
iproute2 (used retain mask, as tc command rewrite whole ToS field):
$ tc filter add dev REP ingress protocol ip prio 1 flower skip_sw \
ip_proto icmp action pedit munge ip tos set 68 retain 0xfc pipe \
action mirred egress redirect dev NIC
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch doesn't change any functionality, but is a pre-step for
adding support for rewriting of bit-sized fields, like DSCP and ECN
in IPv4 header, similar fields in IPv6, etc.
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move short Work Queue API getter functions into the WQ
header file.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
During connection tracking offloads with high number of connections,
(40K connections per second), flow table group lock contention is
observed.
To improve the performance by reducing lock contention, lockless
FTE read lookup is performed as described below.
Each flow table entry is refcounted.
Flow table entry is removed when refcount drops to zero.
rhash table allows rcu protected lookup.
Each hash table entry insertion and removal is write lock protected.
Hence, it is possible to perform lockless lookup in rhash table using
following scheme.
(a) Guard FTE entry lookup per group using rcu read lock.
(b) Before freeing the FTE entry, wait for all readers to finish
accessing the FTE.
Below example of one reader and write in parallel racing, shows
protection in effect with rcu lock.
lookup_fte_locked()
rcu_read_lock();
search_hash_table()
existing_flow_group_write_lock();
tree_put_node(fte)
drop_ref_cnt(fte)
del_sw_fte(fte)
del_hash_table_entry();
call_rcu();
existing_flow_group_write_unlock();
get_ref_cnt(fte) fails
rcu_read_unlock();
rcu grace period();
[..]
kmem_cache_free(fte);
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
FTE memory allocation using alloc_fte() doesn't have any dependency
on the flow group.
Hence, do not hold flow group lock while performing alloc_fte().
This helps to reduce contention of flow group lock.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, mlx5 tc layer doesn't verify that rule has at least one forward
or drop action which leads to following firmware syndrome when user tries
to offload such action:
[ 1824.860501] mlx5_core 0000:81:00.0: mlx5_cmd_check:753:(pid 29458): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x144b7a)
Add check at the end of parse_tc_fdb_actions() that verifies that resulting
attribute has action fwd or drop flag set.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When setting number of VFs to 0 (disable SRIOV), clear VF's
configuration.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_unload_one do not need local variable to store different value,
Hence just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Not all mlx5 cards with FPGA device use it for network processing.
mlx5_core driver configures network connection to FPGA device
for all mlx5 cards with installed FPGA. If FPGA is not a part of
network path, driver crashes in this case
Check FPGA name in function mlx5_fpga_device_start() and continue
integrate FPGA into packets flow only for dedicated cards.
Currently there are Newton and Edison cards.
Signed-off-by: Igor Leshenko <igorle@mellanox.com>
Reviewed-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use kernel function to calculate crc32 Instead of dr implementation
since it has the same algorithm "slice by 8".
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-11-01
This series contains updates to e1000, igb, igc, ixgbe, i40e and driver
documentation.
Lyude Paul fixes an issue where a fatal read error occurs when the
device is unplugged from the machine. So change the read error into a
warn while the device is still present.
Manfred Rudigier found that the i350 device was not apart of the "Media
Auto Sense" feature, yet the device supports it. So add the missing
i350 device to the check and fix an issue where the media auto sense
would flip/flop when no cable was connected to the port causing spurious
kernel log messages.
I fixed an issue where the fix to resolve receive buffer starvation was
applied in more than one place in the driver, one being the incorrect
location in the i40e driver.
Wenwen Wang fixes a potential memory leak in e1000 where allocated
memory is not properly cleaned up in one of the error paths.
Jonathan Neuschäfer cleans up the driver documentation to be consistent
and remove the footnote reference, since the footnote no longer exists in
the documentation.
Igor Pylypiv cleans up a duplicate clearing of a bit, no need to clear
it twice.
v2: Fixed alignment issue in patch 3 of the series based on community
feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently on ECPF, metadata is enabled on the ECPF vport = 0xfffe
(manager vport).
Metadata when supported, must be enabled on own vport which is
used to pass metadata to vport of NIC Rx Flow Table.
Due to this error, traffic tagged by ingress ACL is not processed
correctly at NIC rx flow table level which is supposed to work
on metadata tag.
Hence, instead of working on eswitch manager vport, always working on
eswitch own vport regardless of PF or ECPF.
Given that mlx5_eswitch_query/modify_esw_vport_context() is used to
access other vport in legacy mode and own vport settings in switchdev mode,
extend low level API to explicitly specify other_vport.
Fixes: c1286050cf ("net/mlx5: E-Switch, Pass metadata from FDB to eswitch manager")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Drop, untagged, spoof check and untagged spoof check flow groups are
limited to legacy mode only.
Therefore, following refactoring is done to
(a) improve code readability
(b) have better code split between legacy and offloads mode
1. Move legacy flow groups under legacy structure
2. Add validity check for group deletion
3. Restrict scope of esw_vport_disable_ingress_acl to legacy mode
4. Rename esw_vport_enable_ingress_acl() to
esw_vport_create_ingress_acl_table() and limit its scope to
table creation
5. Introduce legacy flow groups creation helper
esw_legacy_create_ingress_acl_groups() and keep its scope to legacy mode
6. Reduce offloads ingress groups from 4 to just 1 metadata group
per vport
7. Removed redundant IS_ERR_OR_NULL as entries are marked NULL on free.
8. Shortern error message to remove redundant 'E-switch'
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now that there is clear separation for acl setup/cleanup between legacy
and offloads mode, limit metdata disablement to offloads mode.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently legacy mode enables ACL while enabling vport, while offloads
mode enable ACL when moving to offloads mode.
Bring consistency to both modes by enabling/disabling ACL when
enabling/disabling a vport.
It also eliminates creating ingress ACL table on unused ECPF vport in
offloads mode.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce and use per vport ACL tables creation and destroy APIs, so that
subsequently patch can use them during enabling/disabling a vport.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It is better to create/destroy ACL related drop counters where the actual
drop rule ACLs are created/destroyed, so that ACL configuration is self
contained for ingress and egress.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce and use per vport ACL tables creation and destroy APIs, so that
subsequently patch can use them during enabling/disabling a vport in
unified way for legacy vs offloads mode.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In subsequent patch, esw_enable_vport() could fail and return error.
Prepare code to handle such error.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch is disabled, vport event handler is unregistered.
This unregistration already synchronizes with running EQ event handler
in below code flow.
mlx5_eswitch_disable()
mlx5_eswitch_event_handlers_unregister()
mlx5_eq_notifier_unregister()
atomic_notifier_chain_unregister()
synchronize_rcu()
notifier_callchain
eswitch_vport_event()
queue_work()
Additionally vport->enabled flag is set under state_lock during
esw_enable_vport() but is not read under state_lock in
(a) esw_disable_vport() and (b) under atomic context
eswitch_vport_event().
It is also necessary to synchronize with already scheduled vport event.
This is already achieved using below sequence.
mlx5_eswitch_event_handlers_unregister()
[..]
flush_workqueue()
Hence,
(a) Remove vport->enabled check in eswitch_vport_event() which
doesn't make any sense.
(b) Remove redundant flush_workqueue() on every vport disable.
(c) Keep esw_disable_vport() symmetric with esw_enable_vport() for
state_lock.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To improve code readability, move legacy drop counters and droup rule
under legacy structure.
While at it,
(a) prefix drop flow counters helper with legacy_.
(b) nullify the rule pointers only if they were valid.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
fdb_table is used for both legacy and offloads mode.
It was incorrect to comment that fdb_table is legacy specific.
Hence, fix the comment to reflect that fdb_table is used in legacy and
offloads mode.
Fixes: 131ce70140 ("net/mlx5: E-Switch, Remove redundant mc_promisc NULL check")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently esw_enable_vport() does vport check for zero to enable drop
counters regardless of execution on ECPF/PF.
While esw_disable_vport() considers such scenario.
To keep consistency across code for checking for manager_vport,
introduce and use mlx5_esw_is_manager_vport() to check if a specified
vport is eswitch manager vport or not.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Between legacy mode and switchdev mode, only two fields are changed,
vlan_tag and flow action.
Hence to avoid duplicte code between two modes, introduce and and use
helper function to configure allowed VLAN rule.
While at it, get rid of duplicate debug message.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changing the function name esw_ingress_acl_common_config() to
esw_ingress_acl_config() to be consistent with egress config
function naming in offloads mode.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor vport egress config in offloads mode
Refactoring vport egress configuration in offloads mode that
includes egress prio tag configuration.
This makes code symmetric to ingress configuration.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
__IXGBE_RX_BUILD_SKB_ENABLED bit is already cleared.
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Magnus's fix to resolve a potential receive buffer starvation for AF_XDP
got applied to both the i40e_xsk_umem_enable/disable() functions, when it
should have only been applied to the "enable". So clean up the undesired
code in the disable function.
CC: Magnus Karlsson <magnus.karlsson@intel.com>
Fixes: 1f459bdc20 ("i40e: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The remove misses to disable and unprepare priv->macclk like what is done
when probe fails.
Add the missed call in remove.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
100BaseVG AnyLAN hasn't been useful since 1996 or so and even then
didn't sell many devices. It's unlikely any are still in use.
Move the driver to staging with the intent of removing it altogether
one day.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inform the RDMA driver to stop/start during suspend/resume. The
RDMA driver needs to stop and start just like error recovery.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notify the RDMA driver by calling the bnxt_ulp_stop()/bnxt_ulp_start()
hooks during error recovery. The current ULP IRQ start/stop
sequence in error recovery (which is insufficient) is replaced with the
full reset sequence when we call bnxt_ulp_stop()/bnxt_ulp_start().
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bnxt_ulp_stop() to notify the RDMA driver that some error or
imminent reset is about to happen. After that we always call
some variants of bnxt_close().
In the next patch, we will integrate the recently added error
recovery with the RDMA driver. In response to ulp_stop, the
RDMA driver may free MSIX vectors and that will also trigger
bnxt_close(). To avoid bnxt_close() from being called twice,
we set a new flag after ulp_stop is called. If the RDMA driver
frees MSIX vectors while the new flag is set, we will not call
bnxt_close(), knowing that it will happen in due course.
With this change, we must make sure that the bnxt_close() call
after ulp_stop will reset IRQ. Modify bnxt_reset_task()
accordingly if we call ulp_stop.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decap (VXLAN tunnel) flow rules are not getting offloaded with
upstream kernel. This is because TC block callback infrastructure has
been updated to use indirect callbacks to get offloaded rules from
other higher level devices (such as tunnels), instead of ndo_setup_tc().
Since the decap rules are applied to the tunnel devices (e.g, vxlan_sys),
the driver should register for indirect TC callback with tunnel devices
to get the rules for offloading. This patch updates the driver to
register and process indirect TC block callbacks from VXLAN tunnels.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides support for modifying L3/L4 Header parameters to support NAT.
Sets the appropriate fields/bits in cfa_flow_alloc cmd.
Sample cmd for offloading an IPv4 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144,output:p7p1"
Replace 'nw_src' with 'nw_dst' in above cmd for DNAT with IPv4
Sample cmd for offloading an IPv4 flow with SNAPT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144, mod_tp_src:6789,output:p7p1"
Similar to DNAT, replace 'tp_src' with 'tp_dst' for offloading flow
with DNAPT
Sample cmd for offloading an IPv6 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ipv6, ipv6_src=2001:5c0:9168::2/64 \
actions=load:0x1->NXM_NX_IPV6_SRC[0..63], \
load:0x20010db801920000->NXM_NX_IPV6_SRC[64..127],output:p7p1"
Replace 'SRC' with DST' above for IPv6 DNAT
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every single case where bnxt_tc_can_offload() can fail, we are
logging a user friendly descriptive message anyway, but because of the
path it would take in case of failure, another redundant error message
would get logged. Just freeing the node and returning from the point of
failure should suffice.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for packet edit offload of L2 fields (src mac &
dst mac, also referred as L2 rewrite). Only when the mask is fully exact
match for a field, the command is sent down to the adapter to offload
such a flow. Otherwise, an error is returned.
v2: Fix pointer alignment issue in bnxt_fill_l2_rewrite_fields() [MChan]
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function is called at every link up event, although the
FQID values will only change when the DPNI is disconnected from the
current object and reconnected to a different one.
The patch also avoids the forward declaration of update_tx_fqids.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count XDP packet drops, error drops, transmissions and redirects and
expose these counters via the ethtool stats command.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an ndo_xdp_xmit function that uses the XDP tx queue for this
CPU to send the packet.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each CPU needs access to its own queue to allow uncontested
transmission of XDP_TX packets. This means we need to allocate (up
front) enough channels ("xdp transmit channels") to provide at least
one extra tx queue per CPU. These tx queues should not do TSO.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an ndo_bpf function to efx_netdev_ops that allows setting and
querying of xdp programs on an interface.
Also check that the MTU size isn't too big when setting a program or
when the MTU is explicitly set.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a field to hold an attached xdp_prog, but never populates it (see
following patch). Also, XDP_TX support is deferred to a later patch
in the series.
Track failures of xdp_rxq_info_reg() via per-queue xdp_rxq_info_valid
flags and a per-nic xdp_rxq_info_failed flag. The per-queue flags are
needed to prevent attempts to xdp_rxq_info_unreg() structs that failed
to register. Possibly the API could be changed in the future to avoid
the need for these flags.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a field to efx_tx_buffer so that we can track xdp_frames. Add a
flag so that buffers that contain xdp_frames can be identified and
passed to xdp_return_frame.
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When building for 32-bit ARM, there is a link time error because of a
64-bit division:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_buffers.c
>>> net/ethernet/mellanox/mlxsw/spectrum_buffers.o:(mlxsw_sp_buffers_init) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o
Avoid this by using div_u64, which is designed to avoid this problem.
Fixes: bc9f6e94bc ("mlxsw: spectrum_buffers: Calculate the size of the main pool")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all the frames that are in flight have time to be processed
before the interface is completely brought down. Add a missing delay
for the Rx path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User reports that an application making an (incorrect) call to
restart AN on a fixed link DPAA interface triggers an error in
the kernel log while the returned EINVAL should be enough.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, the frames dropped on receive or transmit
were not displayed in the ethtool statistics, leaving the dropped
frames unaccounted for.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a page to store the scatter gather table on the transmit path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading skb fields, use information from the DPAA frame
descriptor.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the buffers used for reception from netdev_frags to pages.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the DPAA Ethernet driver is using three buffer pools
for each interface, with three different sizes for the buffers
provided for the FMan reception path. This patch reduces the
number of buffer pools to one per interface. This change is in
preparation of another, that will be switching from netdev_frags
to page backed buffers for the receive path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though the hip08 and the IMP(Intelligent Management Processor)
have the same byte order right now, it is better to convert
__be or __le variable into the CPU's byte order before print.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using '%d' for printing type unsigned int or '%u' for
type int would cause static tools to give false warnings,
so this patch cleanups this warning by using the suitable
format specifier of the type of variable.
BTW, modifies the type of some variables and macro to
synchronize with their usage.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the comment for macro HCLGE_MBX_GET_VF_FLR_STATUS
more correct, and adds comments in some place to make the code more
readable.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable tx_ring is unnecessary to be initialized as it will be set
before used, and the variable rst_cnt is better to be initialized when
declaration for simplification.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns3_nic_init_irq(), when '*_int_idx' has more than 9 digits
and the length of netdev's name is IFNAMSIZ, the total length
of final name will be bigger the HNAE3_INT_NAME_LEN - 1, even
though '*_int_idx' will never have such large value, but the
compiler gives a format-truncation warning for this case.
So this patch just enlarges the length to avoid this warning.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To unify code style and make code simpler, this patch modifies
some code, deletes unnecessary blank lines and {}, changes
location of code, and so on.
No functional change.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code more readable, this patch replaces
some magic numbers with macro or sizeof operation.
Also uses macro lower_32_bits and upper_32_bits to
get bits 0-31 and 32-63 of a number, instead of
using type conversion and '>>' operation.
No functional change.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a TX timeout, we can tell if the driver or stack
has stopped the queue by looking at state field, and when has
the last packet transmited by looking at trans_start field.
So this patch prints these two field in the
hns3_get_tx_timeo_queue_info().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reset fails, there is some information that will help for
finding out why does reset fail. and removes an unused
core_rst_cnt field in struct hclge_rst_stats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supports 2 types of core dumps.
1. Live dump - Firmware dump when system is up and running.
2. Crash dump - Dump which is collected during firmware crash
that can be retrieved after recovery.
Crash dump is currently supported only on specific 58800 chips
which can be retrieved using OP-TEE API only, as firmware cannot
access this region directly.
User needs to set the dump flag using following command before
initiating the dump collection:
$ ethtool -W|--set-dump eth0 N
Where N is "0" for live dump and "1" for crash dump
Command to collect the dump after setting the flag:
$ ethtool -w eth0 data Filename
v3: Modify set_dump to support even when CONFIG_TEE_BNXT_FW=n.
Also change log message to netdev_info().
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In error recovery process when firmware indicates that it is
completely down, initiate a firmware reset by calling OP-TEE API.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the check generic for any possible value, not only 2 and 4.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During recreation of original unsplit ports, just simply iterate over
the whole gap and recreate whatever originally existed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code considers only split by 2 or 4. Make the base port
getting generic and allow split by 8 to be handled correctly. Generalize
the used port checks as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using constant value, use port_module_max_width which is
aligned with the cluster size.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't compute the original base local port during unsplit, rather
remember it in mlxsw_sp_port structure during split port creation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-3 the modules have 8 lanes, so split by count 2 results in
two split ports each of 4 lanes. Add a resource that can be used to
obtain local port offset in that case.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get local port offsets of split port in a separate helper function and
use it in both split and unsplit function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes certain values in the PMLP register. Add checks that
verify that PMLP register provides fitting values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the port mapping structure down to create, module_map and other
function instead of individual values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use constant max width value and instead of that, use the actual
width of the port. Also don't pass module value and use the value
stored in the same structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
