During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.
Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).
Bisecting turned up commit 93681cd7d9,
"r8169: enable HW csum and TSO" as the culprit.
I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below. This fixed the
performance problem for me.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semicolon is not required at the end of switch block. So, remove it.
Addresses coccinelle warning:
drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon
Fixes: 4846d5330d ("cxgb4: add Tx and Rx path for ETHOFLD traffic")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit had a bug where the last page in the memory range
could not be synced. This change fixes the behavior so that all the
required pages are synced.
Fixes: 9cfeeb576d ("gve: Fixes DMA synchronization")
Signed-off-by: Adi Suresh <adisuresh@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926 ("net/mlx4_en: Limit the number of TX rings")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aRFS ring table interface has changed for the 57500 chips. Updating
it accordingly so it will work with the latest production firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.
mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
92117d8443 ("bpf: fix refcnt overflow") turned refcounting of bpf_map into
potentially failing operation, when refcount reaches BPF_MAX_REFCNT limit
(32k). Due to using 32-bit counter, it's possible in practice to overflow
refcounter and make it wrap around to 0, causing erroneous map free, while
there are still references to it, causing use-after-free problems.
But having a failing refcounting operations are problematic in some cases. One
example is mmap() interface. After establishing initial memory-mapping, user
is allowed to arbitrarily map/remap/unmap parts of mapped memory, arbitrarily
splitting it into multiple non-contiguous regions. All this happening without
any control from the users of mmap subsystem. Rather mmap subsystem sends
notifications to original creator of memory mapping through open/close
callbacks, which are optionally specified during initial memory mapping
creation. These callbacks are used to maintain accurate refcount for bpf_map
(see next patch in this series). The problem is that open() callback is not
supposed to fail, because memory-mapped resource is set up and properly
referenced. This is posing a problem for using memory-mapping with BPF maps.
One solution to this is to maintain separate refcount for just memory-mappings
and do single bpf_map_inc/bpf_map_put when it goes from/to zero, respectively.
There are similar use cases in current work on tcp-bpf, necessitating extra
counter as well. This seems like a rather unfortunate and ugly solution that
doesn't scale well to various new use cases.
Another approach to solve this is to use non-failing refcount_t type, which
uses 32-bit counter internally, but, once reaching overflow state at UINT_MAX,
stays there. This utlimately causes memory leak, but prevents use after free.
But given refcounting is not the most performance-critical operation with BPF
maps (it's not used from running BPF program code), we can also just switch to
64-bit counter that can't overflow in practice, potentially disadvantaging
32-bit platforms a tiny bit. This simplifies semantics and allows above
described scenarios to not worry about failing refcount increment operation.
In terms of struct bpf_map size, we are still good and use the same amount of
space:
BEFORE (3 cache lines, 8 bytes of padding at the end):
struct bpf_map {
const struct bpf_map_ops * ops __attribute__((__aligned__(64))); /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
int spin_lock_off; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
u32 btf_key_type_id; /* 56 4 */
u32 btf_value_type_id; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct btf * btf; /* 64 8 */
struct bpf_map_memory memory; /* 72 16 */
bool unpriv_array; /* 88 1 */
bool frozen; /* 89 1 */
/* XXX 38 bytes hole, try to pack */
/* --- cacheline 2 boundary (128 bytes) --- */
atomic_t refcnt __attribute__((__aligned__(64))); /* 128 4 */
atomic_t usercnt; /* 132 4 */
struct work_struct work; /* 136 32 */
char name[16]; /* 168 16 */
/* size: 192, cachelines: 3, members: 21 */
/* sum members: 146, holes: 1, sum holes: 38 */
/* padding: 8 */
/* forced alignments: 2, forced holes: 1, sum forced holes: 38 */
} __attribute__((__aligned__(64)));
AFTER (same 3 cache lines, no extra padding now):
struct bpf_map {
const struct bpf_map_ops * ops __attribute__((__aligned__(64))); /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
int spin_lock_off; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
u32 btf_key_type_id; /* 56 4 */
u32 btf_value_type_id; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct btf * btf; /* 64 8 */
struct bpf_map_memory memory; /* 72 16 */
bool unpriv_array; /* 88 1 */
bool frozen; /* 89 1 */
/* XXX 38 bytes hole, try to pack */
/* --- cacheline 2 boundary (128 bytes) --- */
atomic64_t refcnt __attribute__((__aligned__(64))); /* 128 8 */
atomic64_t usercnt; /* 136 8 */
struct work_struct work; /* 144 32 */
char name[16]; /* 176 16 */
/* size: 192, cachelines: 3, members: 21 */
/* sum members: 154, holes: 1, sum holes: 38 */
/* forced alignments: 2, forced holes: 1, sum forced holes: 38 */
} __attribute__((__aligned__(64)));
This patch, while modifying all users of bpf_map_inc, also cleans up its
interface to match bpf_map_put with separate operations for bpf_map_inc and
bpf_map_inc_with_uref (to match bpf_map_put and bpf_map_put_with_uref,
respectively). Also, given there are no users of bpf_map_inc_not_zero
specifying uref=true, remove uref flag and default to uref=false internally.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-2-andriin@fb.com
ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the
total number of entries in the rx classifier table. Surprisingly, mlx4
is missing this part (in principle ethtool could still move forward and
try the insert).
Tested: compiled and run command:
phh13:~# ethtool -N eth1 flow-type udp4 queue 4
Added rule with ID 255
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Load Realtek-provided firmware for RTL8168fp/RTL8117. Unlike the
firmware for other chip versions which is for the PHY, firmware for
RTL8168fp/RTL8117 is for the MAC.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using constant MII_EXPANSION is misleading here because register 0x06
has a different meaning on page 0x0005. Here a proprietary PHY
parameter is read by writing the parameter id to register 0x05 on page
0x0005, followed by reading the parameter value from register 0x06.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up the stray left over code. It has no
functionality impact.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 0c65b2b90d ("net: of_get_phy_mode: Change API to solve
int/unit warnings") updated the function of_get_phy_mode declaration.
Now it returns an error code and in case the node doesn't contain the
property 'phy-mode' or 'phy-connection-type' it returns -EINVAL and would
set the phy_interface_t to PHY_INTERFACE_MODE_NA.
Ocelot VSC7514 has 4 internal phys which have the phy interface
PHY_INTERFACE_MODE_NA. So because of_get_phy_mode would assign
PHY_INTERFACE_MODE_NA to phy_mode when there is an error, there is no need
to add the error check.
Updates for v2:
- drop error check because of_get_phy_mode already assigns phy_interface
to PHY_INTERFACE_MODE in case of error.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All .rw_reset callbacks except bnx2x_84833_hw_reset_phy() use a
void return type. No callers of .hw_reset check a return value and
bnx2x_84833_hw_reset_phy() unconditionally returns 0. Remove all
hw_reset_t casts and fix the return type to void.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values for format_fw_ver_t callbacks are supposed to be
"int", not "u8". Ultimately, the top-level caller doesn't actually check
the return value at all, but just clean this all up anyway and fix the
prototypes so that casts are no longer needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No callers of .config_init check return values. Remove the casting and
change all callbacks to have the correct function prototype.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function casts for .read_status callbacks end up casting some int
return values to u8. This seems to be bug-prone (-EINVAL being returned
into something that appears to be true/false), but fixing the function
prototypes doesn't change the existing behavior. Fix the return values
to remove the casts.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NULL is already "void *" so it will auto-cast in assignments and
initializers. Additionally, all the callbacks for .link_reset,
.config_loopback, .set_link_led, and .phy_specific_func are already
correct. No casting is needed for these, so remove them.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC has a register PSPEED to indicate the link speed of hardware.
It is need to update accordingly. PSPEED field needs to be updated
with the port speed for QBV scheduling purposes. Or else there is
chance for gate slot not free by frame taking the MAC if PSPEED and
phy speed not match. So update PSPEED when link adjust. This is
implement by the adjust_link.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to STMicroelectronics based Multi-Gigabit
Ethernet driver. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to Marvell OcteonTX2 network devices.
It uses an expilict block comment for the SPDX License
Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware always time stamps rising and falling edges, and so this
patch validates that the request does contains both edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the renesas PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mlx5 core PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
[ RC: I'm not 100% sure what this driver does, but if I'm not wrong it
follows the dp83640:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp falling edge
]
Cc: Feras Daoud <ferasda@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the igb PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
This HW always time stamps both edges:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp both edges
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls release_resource in remove to match request_mem_region
in probe, which is incorrect.
Fix it by using the right one, release_mem_region.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.
Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.
Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix switch has a different reset procedure, so a function pointer
needs to be created and added to the ocelot_ops structure.
The reset procedure has been moved into ocelot_init.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the NPI port, the DSA tag is passed through Ethernet, so the
switch's MAC needs to accept it as it comes from the DSA master. Increase
the MTU on the external CPU port to account for the length of the
injection header.
Without this patch, MTU-sized frames are dropped by the switch's CPU
port on xmit, which is especially obvious in TCP sessions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constant will be used in a future patch to increase the MTU on NPI
ports, and will also be used in the tagger driver for Felix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since in an NPI/DSA setup, not all ports will have the same MTU, we need
to make sure the watermarks for pause frames and/or tail dropping logic
that existed in the driver is still coherent for the new MTU values.
We need to do this because the NPI (aka external CPU) port needs an
increased MTU for the DSA tag. This will be done in a future patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't make sense to rewrite all these registers every time the PHY
library notifies us about a link state change.
In a future patch we will customize the MTU for the CPU port, and since
the MTU was previously configured from adjust_link, if we don't make
this change, its value would have got overridden.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adjust_link routine should be generic enough to be (re)used by
any SoC that integrates a switch core compatible with the Ocelot
core switch driver. Currently all configurations are generic except
for the PCS settings that are SoC specific. Move these out to the
Ocelot SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make this ioremap and regmap init code common. It should not
be platform dependent as it should be usable by PCI devices too.
Use better names where necessary to avoid clashes.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TX Coalesce has been rewritten we no longer need this
additional interrupt enabled. This reduces CPU usage.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce logic currently increments the number of packets and sets the
IC bit when the coalesced packets have passed a given limit. This does
not reflect very well what coalesce was meant for as we can have a large
number of packets that are coalesced and then a single one, sent later
on that has the IC bit.
Rework the logic so that it coalesces only upon a limit of packets and
sets the IC bit for large number of packets.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tune-up the defalt coalesce settings for optimal values. This gives the
best performance in most of the use-cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For performance reasons, sometimes using the minimum RX Coalesce value
is not optimal. Lets setup a default value that is optimal in most of
the use cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may only want to use the RX Watchdog so lets check if RX Coalesce
settings are non-zero and only set the RX Interrupt on Completion bit if
its not.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0c3cbbf96d ("mlxsw: Add specific trap for packets routed via
invalid nexthops") allocated an adjacency entry during driver
initialization whose purpose is to discard packets hitting the route
pointing to it.
These adjacency entries are allocated from a resource called KVD linear
(KVDL). There are situations in which the user can decide to set the
size of this resource (via devlink-resource) to 0, in which case the
driver will not be able to load.
Therefore, instead of pre-allocating this adjacency entry, simply
allocate it only when needed. A variable indicating the validity of the
entry is added and is used to ensure it is only allocated and written
once and that it is freed after all the routes were flushed.
Fixes: 0c3cbbf96d ("mlxsw: Add specific trap for packets routed via invalid nexthops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic for a CGX mapped NIXLF can be stopped by disabling entries
in NPC MCAM or by configuring CGX and mailbox messages exist for the
two options. If traffic is stopped at CGX then VFs of that PF are
also effected hence CGX traffic should be started/stopped by
tracking all the users of it. This patch implements that CGX users
tracking. CGX is also configured along with NPC if required.
Also removed a check which mandates even number of LBK VFs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A config option is added to disable caching of dynamic entries
like SQEs and stack pages. Also locks down all HW contexts in NDC,
preventing them from being evicted.
This option is useful when the queue count is large and there are
huge NDC cache misses. It's trade off between SQ context misses and
dynamically changing entries like SQE and stack page pointers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the NIX/NPA LFs can choose which ways of their respective
NDC caches should be used to cache their contexts. This enables
flexible configurations like disabling caching for a LF, limiting
it's context to a certain set of ways etc etc. Separate way_mask
for NIX-TX and NIX-RX is not supported.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress packet replication support has been added to 96xx B0
silicon. This patch enables using that feature to replicate
ingress broadcast packets to PF and it's VFs.
Also fixed below issues
- VFs can also install NPC MCAM entry to forward broadcast pkts.
Otherwise, unless PF's interface is UP, VFs will not receive
bcast packets.
- NPC MCAM entry is disabled when PF and all it's VFs are down.
- Few corner cases in installing multicast entry list.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN96xx initial silicon doesn't support all features pertaining to
NIX transmit scheduling and shaping.
- It supports a fixed topology of 1:1 mapped transmit
limiters at all levels.
- Supports DWRR only at SMQ/MDQ and TL1.
- Doesn't support shaping and coloring.
This patch adds HW capability structure by which each variant
and skew of silicon can be differentiated by their supported
features. And adds support for A0 silicon's transmit scheduler
capabilities or rather limitations.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for few more RSS key types for flow key
algorithm to compute rss hash index.
Following flow key types have been added.
- Tunnel types like NVGRE, VXLAN, GENEVE.
- L2 offload type ETH_DMAC, Here we will consider only DMAC 6 bytes.
- And extension header IPV6_EXT (1 byte followed by IPV6 header
- Hashing inner protocol fields for inner DMAC, IPv4/v6, TCP, UDP, SCTP.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing into NPC MCAM1 and MCAM0 registers are suppressed if
they happened to form a reserved combination. Hence
clear and disable MCAM entries before update.
For HRM:
[CAM(1)]<n>=1, [CAM(0)]<n>=1: Reserved.
The reserved combination is not allowed. Hardware suppresses any
write to CAM(0) or CAM(1) that would result in the reserved combination for
any CAM bit.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated NPC KPU packet parsing profile with support for following
- Fragmentation support for IPv4 IPv6 outer header
- NIX instruction header support
- QinQ with TPID of 0x8100 as non inner most vlan tag, as legacy
network equipments still generate QinQ packets with this configuration.
- To better support RSS for tunnelled packets, udp based tunnel
protocols such as vxlan, vxlan-gpe, geneve and gtpu are now
captured into a separate layer E. Consequently, the inner
packet headers are pushed one layer down to LF, LG, and LH
accordingly.
- Support for rfc7510 mpls in udp. Up to 4 MPLS labels can be parsed
and captured in one layer LE.
- Parser support for DSA, extended DSA and eDSA tags right after
ethernet header by Marvell SOHO and Falcon switches. For extended
DSA and eDSA tags, a special PKIND of 62 is used, as these tags don't
contain a tpid field.
- Higig2 protocol header parsing support, added a NPC_LT_LA_HIGIG2_ETHER
for a combined header of HIGIG2 and Ethernet. Add a
NPC_LT_LA_IH_NIX_HIGIG2_ETHER for a combined header of nix_ih,
HIGIG2 and Ethernet on egress side. Also added 2 upper flags in LA to
indicate the presence of nix_ih and HIGIG2.
Other changes include
- IPv4.TTL==0 IPv6.HLIM==0 check
- Per RFC 1858, mark fragment offset == 1 as error
- TCP invalid flags check
- Separate error codes for outer and inner IPv4 checksum errors.
- Fix a parser error when KPU parses incoming IPSec ESP and AH packets
- NPC vtag capture/strip hardware expect tag pointer to point to
tpid/ethertype instead of tci. So move lb_ptr to point to tpid/ethertype.
- Fix npc parser error when parsing udp packets that don't have any payload.
- For a single MCAM entry to match on packets with one or stacked vlan tags
combine NPC_LT_LB_STAG and NPC_LT_LB_QINQ to NPC_LT_LB_STAG_QINQ.
- NVGRE to have a separate ltype LD_NVGRE instead of combined with LD_GRE.
- Reserve top LD/LTYPEs to support custom KPU profile fields.
Signed-off-by: Hao Zheng <haoz@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every mailbox handler added to rvu, we are adding a function
declaration in rvu header file. Cleaned this up by adding a macro
to generate these declarations automatically.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mailbox client has a bounce buffer or a intermediate buffer where
mbox messages are framed then copy them from there to HW buffer.
If 'mbase' and 'hw_mbase' are not same then assume 'mbase' points to
bounce buffer.
This patch also adds msg_size field to mbox header to copy only valid
data instead of whole buffer.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new mailbox API which goes through all responses
to check their IDs and response codes.
Also added logic to prevent queuing multiple works to
process the same mailbox message. This scenario happens
when AF is processing a PF's request and menawhile PF
sends ACK to AF sent UP message, then mbox_hdr->num_msgs
in the PF->AF DOWN mbox region will be nonzero and AF
will end up processing PF's request again. This is fixed
by taking a backup of num_msgs counter and clearing the
same in the mbox region before scheduling work.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support to display current NPC MCAM entries and counter's allocation
status ín debugfs.
cat /sys/kernel/debug/octeontx2/npc/mcam_info' will dump following info
- MCAM Rx and Tx keysize
- Total MCAM entries and counters
- Current available count
- Count of number of MCAM entries and counters allocated
by a RVU PF/VF device.
Also, one NPC MCAM counter (last one) is reserved and mapped to
NPC RX_INTF's MISS_ACTION to count dropped packets due to no MCAM
entry match. This pkt drop counter can be checked via debugfs.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CGX port is shared by a RVU PF and it's VFs. These per
CGX port level NIX Rx/Tx counters are cumilative stats of
all NIXLFs sharing this port. These stats when compared
to CGX Rx/Tx stats helps in identifying pkts dropped within
the system, if any.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds CGX LMAC physical interface or serdes Rx/Tx
packet stats to debugfs.
'cat cgx<idx>/lmac<idx>/stats' dumps the current interface link
status and Rx/Tx stats. Stats include pkt received/transmitted,
dropped, pause frames etc etc.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NDC is a data cache unit which caches NPA and NIX block's
aura/pool/RQ/SQ/CQ/etc contexts to reduce number of costly
DRAM accesses.
This patch adds support to dump cache's performance stats
like cache line hit/miss counters, average cycles taken for
accessing cached and non-cached data. This will help in
checking if NPA/NIX context reads/writes are having NDC cache
misses which inturn might effect performance.
Also changed NDC enums to reflect correct NDC hardware instance.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To aid in debugging NIX block related issues, added support to dump
NIX block LF's RQ, SQ and CQ hardware contexts in debugfs. User can
check which contexts are enabled currently and dump it's current HW
context.
Four new files 'qsize', 'rq_ctx', 'sq_ctx' and 'cq_ctx' are added to the
debugfs at 'sys/kernel/debug/octeontx2/nix/'
'echo <nixlf index> > qsize' will display current enabled CQ/SQ/RQs.
'echo <nixlf> [rq number/all] > rq_ctx',
'echo <nixlf> [sq number/all] > sq_ctx' &
'echo <nixlf> [cq number/all] > cq_ctx' will dump RQ/SQ/CQ's current
hardware context.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To aid in debugging NPA related issues, added support to dump
NPA (pool allocator) block LF's aura and pool hardware contexts in
debugfs. User can check which contexts are enabled currently and dump
it's current HW context.
Three new files 'qsize', 'aura_ctx', 'pool_ctx' are added to the
debugfs at 'sys/kernel/debug/octeontx2/npa/'
'echo <npalf index> > qsize' will display current enabled Aura/Pools.
'echo <npalf> [aura number/all] > aura_ctx' &
'echo <npalf> [aura number/all] > pool_ctx' will dump Aura/Pool
context info.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support to dump current resource provisioning status
of all resource virtualization unit (RVU) block's
(i.e NPA, NIX, SSO, SSOW, CPT, TIM) local functions attached
to a PF_FUNC into a debugfs file.
'cat /sys/kernel/debug/octeontx2/rsrc_alloc'
will show the current block LF's allocation status.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device only support 4 TCs, but the driver check the total
bandwidth of 8 TCs, so may cause wrong configurations write to
the hw.
This patch uses hdev->tc_max to instead HNAE3_MAX_TC to fix it.
Fixes: e432abfb99 ("net: hns3: add common validation in hclge_dcb")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a TC's PFC is disabled or enabled, the RX private buffer for
this TC need to be changed too, otherwise this may cause packet
dropped problem.
This patch fixes it by calling hclge_buffer_alloc to reallocate
buffer when pfc_en changes.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, hns3 driver just directly send specific setting bit
and mask bits of MAC VLAN switch parameter to the firmware, it
can not be compatible with the old firmware, because the old one
ignores mask bits and covers all bits with new setting bits.
So when running with old firmware, the communication between PF
and VF will fail after resetting or configuring spoof check, since
they will do the MAC VLAN switch parameter configuration.
This patch fixes this problem by reading switch parameter firstly,
then just modifies the corresponding bit and sends it to firmware.
Fixes: dd2956eab1 ("net: hns3: not allow SSU loopback while execute ethtool -t dev")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocates buffers sufficient for the maximum supported MTU (2026) in
order to eliminate the possibility of resource exhaustion when changing the
MTU while the device is up.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build_skb for bm capable devices when they fall-back using swbm path
(e.g. when bm properties are configured in device tree but
CONFIG_MVNETA_BM_ENABLE is not set). In this case rx_offset_correction is
overwritten so we need to use it building skb instead of
MVNETA_SKB_HEADROOM directly
Fixes: 8dc9a0888f ("net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine")
Fixes: 0db51da7a8 ("net: mvneta: add basic XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use r8168d_modify_extpage() also in rtl8168f_config_eee_phy() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when ibmveth receive a loopback packet, it reports an
ambiguous error message "tx: h_send_logical_lan failed with rc=-4"
because the hypervisor rejects those types of packets. This fix
detects loopback packet and assures the source packet's MAC address
matches the driver's MAC address before transmitting to the
hypervisor.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable GDM GDMA_DROP_ALL mode to drop all packet during the
stop operation. This is recommended by the mt762x HW design
to drop all packet from GMAC before stopping PDMA.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refine the timing of GDM/PSE setup, move it from mtk_hw_init
to mtk_open. This is recommended by the mt762x HW design to
do GDM/PSE setup only after PDMA has been started.
We exclude mt7628 in mtk_gdm_config function since it is a old IP
and there is no GDM/PSE block on it.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate GDM/PSE setup operations into single function "mtk_gdm_config"
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ret" is zero or possibly uninitialized on this error path. It
should be a negative error code instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irqreturn_t type is an enum and in this context it's unsigned, so "err"
can't be irqreturn_t or it breaks the error handling. In fact the "err"
variable is only used to store integers (never irqreturn_t) so it should
be declared as int.
I removed the initialization because it's not required. Using a bogus
initializer turns off GCC's uninitialized variable warnings. Secondly,
there is a GCC warning about unused assignments and we would like to
enable that feature eventually so we have been trying to remove these
unnecessary initializers.
Fixes: 7b0c342f1f ("net: atlantic: code style cleanup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the array overrun while keeping the eth_addr and eth_addr_mask
pointers as u16 to avoid unaligned u16 access. These were overlooked
when modifying the code to use u16 pointer for proper alignment.
Fixes: 90f906243b ("bnxt_en: Add support for L2 rewrite")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both tc rules and flow table rules are of the same format,
we can re-use tc parsing for that, and move the flow table rules
to their steering domain - In this case, the next chain after
max tc chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use devlink instance name space to set the netdev net namespace.
Preparation patch for devlink reload implementation.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Be sure to release the neighbour in case of failures after successful
route lookup.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Neighbour initializations to NULL are not necessary as the pointers are
not used if an error is returned, and if success returned, pointers are
initialized.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_device_disable_sriov() currently reads num_vfs from the PCI core.
However when mlx5_device_disable_sriov() is executed, SR-IOV is
already disabled at the PCI level.
Due to this disable_hca() cleanup is not done during SR-IOV disable
flow.
mlx5_sriov_disable()
pci_enable_sriov()
mlx5_device_disable_sriov() <- num_vfs is zero here.
When SR-IOV enablement fails during mlx5_sriov_enable(), HCA's are left
in enabled stage because mlx5_device_disable_sriov() relies on num_vfs
from PCI core.
mlx5_sriov_enable()
mlx5_device_enable_sriov()
pci_enable_sriov() <- Fails
Hence, to overcome above issues,
(a) Read num_vfs before disabling SR-IOV and use it.
(b) Use num_vfs given when enabling sriov in error unwinding path.
Fixes: d886aba677 ("net/mlx5: Reduce dependency on enabled_vfs counter and num_vfs")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When selecting a matcher ste_builder_arr will always be evaluated
as true, instead check if num_of_builders is set for validity.
Fixes: 667f264676 ("net/mlx5: DR, Support IPv4 and IPv6 mixed matcher")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Netfilter tables (nftables) implements a software datapath that
comes after tc ingress datapath. The datapath supports offloading
such rules via the flow table offload API.
This API is currently only used by NFT and it doesn't provide the
global priority in regards to tc offload, so we assume offloading such
rules must come after tc. It does provide a flow table priority
parameter, so we need to provide some supported priority range.
For that, split fastpath prio to two, flow table offload and tc offload,
with one dedicated priority chain for flow table offload.
Next patch will re-use the multi chain API to access this chain by
allowing access to this chain by the fdb_sub_namespace.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Next patch will re-use this to add a new chain but in a
different prio.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tc chains are implemented by creating a chained prio steering type, and
inside it there is a namespace for each chain (FDB_TC_MAX_CHAINS). Each
of those has a list of priorities.
Currently, all namespaces in a prio start at the parent prio level.
But since we can jump from chain (namespace) to another chain in the
same prio, we need the levels for higher chains to be higher as well.
So we created unused prios to account for levels in previous namespaces.
Fix that by accumulating the namespaces levels if we are inside a chained
type prio, and removing the unused prios.
Fixes: 328edb499f ('net/mlx5: Split FDB fast path prio to multiple namespaces')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Define FDB_TC_LEVELS_PER_PRIO instead of magic number 2.
This is the number of levels used by each tc prio table in the fdb.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename it to prepare for next patch that will add a
different type of offload to the FDB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
FDB_MAX_CHAIN and FDB_MAX_PRIO were defined differently depending
on if CONFIG_MLX5_ESWITCH is enabled to save space on allocations.
This is a minor space saving, and there is no real need for it.
Simplify things instead, and define them the same in both cases.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is a return statement that is indented too deeply, remove
the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the MACB Ethernet driver to the Phylink framework.
The MAC configuration is moved to the Phylink ops and Phylink helpers
are now used in the ethtools functions. This helps to access the flow
control and pauseparam logic and this will be helpful in the future for
boards using this controller with SFP cages.
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the Tx and Rx buffer initialization into its own
function. This does not modify the behaviour of the driver and will be
helpful to convert the driver to phylink.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable xilinx axi_emac driver support on zynqmp ultrascale platform
(ARCH64) there are two choices, mention ARCH64 as a dependency list
and other is to check if this ARCH dependency list is really needed.
Later approach seems more reasonable, so remove the obsolete ARCH
dependency list for the axi_emac driver.
Sanity test done for microblaze, zynq and zynqmp ultrascale platform.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing support for the PHY mode RGMII_RXID.
It's necessary for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register access in bcmgenet_mii_config() is a little bit opaque and
not easy to extend. In preparation for the missing RGMII PHY modes
move all the phy name assignments into the switch statement and the
register access to the end of the function. This make the code easier
to read and extend.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM2711 needs a different maximum DMA burst length. If not set
accordingly a timeout in the transmit queue happens and no package
can be sent. So use the new compatible to derive this value.
Until now the GENET HW version was used as the platform identifier.
This doesn't work with SoC-specific modifications, so introduce a proper
platform data structure.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the error handling for the mandatory IRQs. There is no need
for the error message anymore, this is now handled by platform_get_irq.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As platform_get_irq() now prints an error when the interrupt does not
exist, we are getting a confusing error message in case the optional
WOL IRQ is not defined:
bcmgenet fd58000.ethernet: IRQ index 2 not found
Fix this by using the platform_get_irq_optional().
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfc driver can drop packets processed with XDP, notably when running
out of buffer space on XDP_TX, or returning an unknown XDP action.
This increments the rx_xdp_bad_drops ethtool counter.
Call trace_xdp_exception everywhere rx_xdp_bad_drops is incremented,
except for fragmented RX packets as the XDP program hasn't run yet.
This allows it to easily be monitored from userspace.
This mirrors the behavior of other drivers.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant code from fw_fatal reporter's dump callback. Use
updated devlink interface of binary fmsg pair which breaks the output
into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c:242:6: warning: symbol 'cxgb4_mqprio_free_hw_resources' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:706:5: warning: symbol 'aq_ethtool_get_priv_flags' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:713:5: warning: symbol 'aq_ethtool_set_priv_flags' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:426:25: warning: symbol 'aq_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to enable EMAD string TLV only after using the required firmware
version.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the firmware had an error while processing EMADs, it can send back
an ASCII string with the reason using EMAD string TLV.
This patch adds the support for using EMAD string TLV. In case of an error,
reports the reason using devlink hwerr tracepoint.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend EMAD information reported to devlink hwerr tracepoint with
transaction id and reg id (both, hex and string).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During parsing of incoming EMADs, fill the string TLV's offset when it is
used.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EMAD string TLV, an ASCII string the driver can receive from the
firmware in case of an error.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the code assumes a fixed structure which makes it difficult to
support EMADs with and without new TLVs.
Make it more generic by parsing the TLVs when the EMADs are received and
store the offset to the different TLVs in the control block. Using these
offsets to extract information from the EMADs without relying on a specific
structure.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TI_DAVINCI_EMAC=y and GENERIC_ALLOCATOR is not set,
below erros can be seen:
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.14':
davinci_cpdma.c:(.text+0x359): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x365): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x373): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x37f): undefined reference to `gen_pool_size'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x4a2): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit_si':
davinci_cpdma.c:(.text+0x66c): undefined reference to `gen_pool_alloc_algo_owner'
davinci_cpdma.c:(.text+0x805): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
davinci_cpdma.c:(.text+0xabd): undefined reference to `devm_gen_pool_create'
davinci_cpdma.c:(.text+0xb79): undefined reference to `gen_pool_add_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
davinci_cpdma.c:(.text+0x16c6): undefined reference to `gen_pool_avail'
This patch mades TI_DAVINCI_EMAC select GENERIC_ALLOCATOR.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the UDP Segmentation Offload feature in stmmac. This is only
available in GMAC4+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks over-engineered. Let's use some helpers to get the buffer
length and hereby simplify the stmmac_rx() function. No performance drop
was seen with the new implementation.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.
v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VID is converted to le16 so the variable must be __le16 type.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254b ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC7514 is a 10-port switch with 2 extra "CPU ports" (targets in the
queuing subsystem for terminating traffic locally).
There are 2 issues with hardcoding the CPU port as #10:
- It is not clear which snippets of the code are configuring something
for one of the CPU ports, and which snippets are just doing something
related to the number of physical ports.
- Actually any physical port can act as a CPU port connected to an
external CPU (in addition to the local CPU). This is called NPI mode
(Node Processor Interface) and is the way that the 6-port VSC9959
(Felix) switch is integrated inside NXP LS1028A (the "local management
CPU" functionality is not used there).
This patch makes it clear that the ocelot_bridge_stp_state_set function
operates on the CPU port (by making it an implicit member of the
bridging domain), and at the same time adds logic for the NPI port (aka
a physical port) to play the role of a CPU port (it shouldn't be part of
bridge_fwd_mask, as it's not explicitly enslaved to a bridge).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the places that configure routing destinations for the CPU port
have been marked as such, allow callers to specify their own CPU port
that is different than ocelot->num_phys_ports. A user will be the Felix
DSA driver, where the CPU port is one of the physical ports (NPI mode).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be called from the Felix DSA frontend, which will work in
PHYLIB compatibility mode initially.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just common path code that belongs to ocelot_init,
it has nothing to do with a specific SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow these functions to be called from the .port_enable and
.port_disable callbacks of DSA.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a function for the DSA front-end that does none of the
net_device registration, but initializes the hardware ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 switch (Ocelot) is a 10-port device, while VSC9959 (Felix)
is 6-port. Therefore the VLAN filtering mask would be out of bounds when
calling for this new switch. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert them into an implementation that can be called from DSA as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot and ocelot_port structures will be used by a new DSA driver,
so the ocelot_board.c file will have to allocate and work with a private
structure (ocelot_port_private), which embeds the generic struct
ocelot_port. This is because in DSA, at least one interface does not
have a net_device, and the DSA driver API does not interact with that
anyway.
The ocelot_port structure is equivalent to dsa_port, and ocelot to
dsa_switch. The members of ocelot_port which have an equivalent in
dsa_port (such as dp->vlan_filtering) have been moved to
ocelot_port_private.
We want to enforce the coding convention that "ocelot_port" refers to
the structure, and "port" refers to the integer index. One can retrieve
the structure at any time from ocelot->ports[port].
The patch is large but only contains variable renaming and mechanical
movement of fields from one structure to another.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port structure has a net_device embedded in it, which makes
it unsuitable for leaving it in the driver implementation functions.
Leave ocelot_flower.c untouched. In that file, ocelot_port is used as an
interface to the tc shared blocks. That will be addressed in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the Felix DSA front-end can call the Ocelot
implementations.
The implementation of the "mc_disabled" switchdev attribute has also
been simplified by using the read-modify-write macro instead of
open-coding that operation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in order to present a simpler prototype to the DSA
front-end of ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to implement a DSA front-end over ocelot_fdb_add,
ocelot_fdb_del, ocelot_fdb_dump, these need to have a simple function
prototype that is independent of struct net_device, netlink skb, etc.
So rename the ndo ops of the ocelot driver into
ocelot_port_fdb_{add,del,dump}, and have them all call the abstract
implementations. At the same time, refactor ocelot_port_fdb_do_dump into
a function whose prototype is compatible with dsa_fdb_dump_cb_t, so that
the do_dump implementations can live together and be called by the
ocelot_fdb_dump through a function pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need an implementation of these functions that is agnostic to the
higher layer (switchdev or dsa).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch transforms the ocelot_vlan_port_apply function ("apply
what?") into 3 standalone functions:
- ocelot_port_vlan_filtering
- ocelot_port_set_native_vlan
- ocelot_port_set_pvid
These functions have a prototype that is better aligned to the DSA API.
The function also had some static initialization (TPID, drop frames with
multicast source MAC) which was not being changed from any place, so
that was just moved to ocelot_probe_port (one of the 6 callers of
ocelot_vlan_port_apply).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.
The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output
The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register "enable_roce" param, default value is RoCE enabled.
Current configuration is stored on mlx5_core_dev and exposed to user
through the cmode runtime devlink param.
Changing configuration requires changing the cmode driverinit devlink
param and calling devlink reload.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-08
Another series that contains updates to the ice driver only.
Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration. Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.
Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.
Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.
Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.
Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.
Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.
Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.
Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF. Updates a flag bit
to align with the current specification.
Bruce updates a switch statement to use the correct status of the
Download Package AQ command. Does some housekeeping by cleaning up a
conditional check that is not needed.
Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.
Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in. Improve debugging by adding the command opcode in the debug
messages that print an error code.
v2: fixed reverse christmas tree issue in patch 3 of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU can be a frequent operation and it is already clear
when (or not) a MTU change is successful, demote prints to debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.
Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update on more short variant for getting real clock in ns.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia is now part of Marvell, eventually we'll cease standalone
aquantia.com domain. Thus, change the maintainers file and some other
references to @marvell.com domain
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atlantic hardware does support UDP hardware segmentation offload.
This allows user to specify one large contiguous buffer with data
which then will be split automagically into multiple UDP packets
of specified size.
Bulk sending of large UDP streams lowers CPU usage and increases
bandwidth.
We did estimations both with udpgso_bench_tx test tool and with modified
iperf3 measurement tool (4 streams, multithread, 200b packet size)
over AQC<->AQC 10G link. Flow control is disabled to prevent RX side
impact on measurements.
No UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 200 -P4 --multithread
UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 12600 --udp-lso 200 -P4 --multithread
Mode CPU iperf speed Line speed Packets per second
-------------------------------------------------------------
NO UDP GSO 350% 3.07 Gbps 3.8 Gbps 1,919,419
SW UDP GSO 200% 5.55 Gbps 6.4 Gbps 3,286,144
HW UDP GSO 90% 6.80 Gbps 8.4 Gbps 4,273,117
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now differentiate requested and negotiated flow control
modes. Therefore `ethtool -A` now operates on local requested
FC values, and regular link settings shows the negotiated FC
settings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to follow the naming of the chip (atlantic), not
company. So replace some old namings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats a pure checkpatck walkthrough the code with no functional
changes. Reverse christmas tree, spacing, etc.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
