Remove the static variable. So these common clock register helper could
be used in more SoCs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
WARNING: drivers/clk/socfpga/built-in.o(.data+0xc0): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_pll_init()
The variable socfpga_child_clocks references
the function __init socfpga_pll_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/clk/socfpga/built-in.o(.data+0x184): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_periph_init()
The variable socfpga_child_clocks references
the function __init socfpga_periph_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/clk/socfpga/built-in.o(.data+0x248): Section mismatch in
reference from the variable socfpga_child_clocks to the function
.init.text:socfpga_gate_init()
The variable socfpga_child_clocks references
the function __init socfpga_gate_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Reported-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since clock operation within S2MPS11 and S5M8767 are similar, we can
support both the devices within a single driver.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clocks in S2MPS11 and S5M8767 are managed in the same way, baring
a difference in the register offset. It would be better to update
existing S2MPS11 driver to support the clocks in S5M8767, rather than
creating an almost duplicate driver altogether.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
MOXA ART SoCs allow to determine PLL output and APB frequencies
by reading registers holding multiplier and divisor information.
Add a clock driver for this SoC.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Move of_clk_init() from clock driver to enable
options not to use zynq clock driver.
Use for example fixed clock setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adds support for the Core Divider clocks of the Armada
380 SoCs. Similarly to Armada 370 and XP, the Core Divider clocks of
the 380 have gate capabilities. The only difference is the register layout.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-2-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When arch/arm/mach-omap2/gpmc.c calls clk_get(..., "fck"), it will
get a dummy clock and try to use it. As the rate is configured to zero,
this will result in several divisions by zero, and misconfigured
timings, with devices on the bus being lost in the La La Land.
It is better to remove gpmc_fck from the dummy clocks, so that gpmc.c
can fail gracefully.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPU frequency cannot be scaled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=UEPE
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clk driver fix from Mike Turquette:
"Single fix for a clock driver merged in 3.14-rc1. Without this fix
the CPU frequency cannot be scaled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change
The Z clock frequency change is effective only after setting the kick
bit located in the FRQCRB register.
Without that, the CA15 CPUs clock rate will never change.
Fix that by checking if the kick bit is cleared and enable it to make
the clock rate change effective. The bit is cleared automatically upon
completion.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This pull request contains the Broadcom bcm281xx
clock driver series. This series is being merged
through the arm-soc tree because there is an
ordering dependency where the driver *must* be
merged before the related dts changes. This is
a result of the bcm281xx dts already containing
dummy fixed clock nodes that must be updated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kma/
-----END PGP SIGNATURE-----
Merge tag 'armsoc/for-3.15/drivers' of git://github.com/broadcom/mach-bcm into next/drivers
Merge "ARM: mach-bcm: bcm281xx clock driver" from Matt Porter:
This pull request contains the Broadcom bcm281xx
clock driver series. This series is being merged
through the arm-soc tree because there is an
ordering dependency where the driver *must* be
merged before the related dts changes. This is
a result of the bcm281xx dts already containing
dummy fixed clock nodes that must be updated.
* tag 'armsoc/for-3.15/drivers' of git://github.com/broadcom/mach-bcm:
clk: bcm281xx: don't disable unused peripheral clocks
clk: bcm281xx: add initial clock framework support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ti/clk-divider.c does not calculate the rates consistently at the moment.
As an example, on OMAP3 we have a clock divider with a source clock of
864000000 Hz. With dividers 6, 7 and 8 the theoretical rates are:
6: 144000000
7: 123428571.428571...
8: 108000000
Calling clk_round_rate() with the rate in the first column will give the
rate in the second column:
144000000 -> 144000000
143999999 -> 123428571
123428572 -> 123428571
123428571 -> 108000000
Note how clk_round_rate() returns 123428571 for rates from 123428572 to
143999999, which is mathematically correct, but when clk_round_rate() is
called with 123428571, the returned value is surprisingly 108000000.
This means that the following code works a bit oddly:
rate = clk_round_rate(clk, 123428572);
clk_set_rate(clk, rate);
As clk_set_rate() also does clock rate rounding, the result is that the
clock is set to the rate of 108000000, not 123428571 returned by the
clk_round_rate.
This patch changes the ti/clk-divider.c to use DIV_ROUND_UP when
calculating the rate. This gives the following behavior which fixes the
inconsistency:
144000000 -> 144000000
143999999 -> 123428572
123428572 -> 123428572
123428571 -> 108000000
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-divider.c does not calculate the rates consistently at the moment.
As an example, on OMAP3 we have a clock divider with a source clock of
864000000 Hz. With dividers 6, 7 and 8 the theoretical rates are:
6: 144000000
7: 123428571.428571...
8: 108000000
Calling clk_round_rate() with the rate in the first column will give the
rate in the second column:
144000000 -> 144000000
143999999 -> 123428571
123428572 -> 123428571
123428571 -> 108000000
Note how clk_round_rate() returns 123428571 for rates from 123428572 to
143999999, which is mathematically correct, but when clk_round_rate() is
called with 123428571, the returned value is surprisingly 108000000.
This means that the following code works a bit oddly:
rate = clk_round_rate(clk, 123428572);
clk_set_rate(clk, rate);
As clk_set_rate() also does clock rate rounding, the result is that the
clock is set to the rate of 108000000, not 123428571 returned by the
clk_round_rate.
This patch changes the clk-divider.c to use DIV_ROUND_UP when
calculating the rate. This gives the following behavior which fixes the
inconsistency:
144000000 -> 144000000
143999999 -> 123428572
123428572 -> 123428572
123428571 -> 108000000
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cppcheck detected following error
[clk-master.c:245]: (error) Memory leak: characteristics
The original code forgot to free characteristics when
irq_of_parse_and_map() failed.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for the new v2 version of the axi-clkgen core.
Unfortunately the method of accessing the registers is quite different on v2,
while the content still stays largely the same. So the patch adds a small
abstraction layer which implements the specific read and write functions for v1
and v2 in callback functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Suggest by Arnd: abstract mmc tuning as clock behavior,
also because different soc have different tuning method and registers.
hi3620_mmc_clks is added to handle mmc clock specifically on hi3620.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The PLLs can be from 3 different sources: osc1, osc2, or the f2s_ref_clk.
Update the clock driver to be able to get the correct parent.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use 64-bit integer for calculating clock rate. Also use do_div for the
64-bit division.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Nomadik debugfs screws up multiplatform boots if debugfs
is enabled on the multiplatform image, since it's a simple
initcall that is unconditionally executed and reads from certain
memory locations.
Fix this by checking that the driver has been properly
initialized, so a base offset to the Nomadik SRC controller
exists, before proceeding to register debugfs files.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As we move toward multiplatform support for the Integrator family
we need to localize all <mach/*> headers. This moves the impd1.h
header down to the machine folder, copying the the three defines
only used by the clock driver down into the clock driver.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Austin <jonathan.austin@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not use readl/writel directly because the whole
clk subsystem is using clk_readl/clk_writel functions.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
These variable clocks have nothing to do with MSTP gating, probably a
copy&paste leftover.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cpu0 clock node has no functionality, since cpufreq-cpu0 is already
capable of picking up the clock from dts.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Ensure clk->kref is dereferenced only when clk is not NULL.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
At probe time, a clock device may not be ready when some other device
wants to use it.
This patch lets the functions clk_get/devm_clk_get return a probe defer
when the clock is defined in the DT but not yet available.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Both the pr_err and the additional kerneldoc aim to help when debugging
errors thrown from within a clock rate-change notifier callback.
Reported-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fixes stray access to undefined registers, use of wrong clock parents &
running clocks at wrong rates. All of these issues cause regressions in
the form of boards that are unable to boot or crash and die horrible
deaths.
Add the CLK_IGNORE_UNUSED flag when setting up a peripheral clock.
This prevents unused clocks from getting disabled, and by doing
this we can use the common clock code even before we've resolved
all the spots that need to get a reference to their clock.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Add code for device tree support of clocks in the BCM281xx family of
SoCs. Machines in this family use peripheral clocks implemented by
"Kona" clock control units (CCUs). (Other Broadcom SoC families use
Kona style CCUs as well, but support for them is not yet upstream.)
A BCM281xx SoC has multiple CCUs, each of which manages a set of
clocks on the SoC. A Kona peripheral clock is composite clock that
may include a gate, a parent clock multiplexor, and zero, one
or two dividers. There is a variety of gate types, and many gates
implement hardware-managed gating (often called "auto-gating").
Most dividers divide their input clock signal by an integer value
(one or more). There are also "fractional" dividers which allow
division by non-integer values. To accomodate such dividers,
clock rates and dividers are generally maintained by the code in
"scaled" form, which allows integer and fractional dividers to
be handled in a uniform way.
If present, the gate for a Kona peripheral clock must be enabled
when a change is made to its multiplexor or one of its dividers.
Additionally, dividers and multiplexors have trigger registers which
must be used whenever the divider value or selected parent clock is
changed. The same trigger is often used for a divider and
multiplexor, and a BCM281xx peripheral clock occasionally has two
triggers.
The gate, dividers, and parent clock selector are treated in this
code as "components" of a peripheral clock. Their functionality is
implemented directly--e.g. the common clock framework gate
implementation is not used for a Kona peripheral clock gate. (This
has being considered though, and the intention is to evolve this
code to leverage common code as much as possible.)
The source code is divided into three general portions:
drivers/clk/bcm/clk-kona.h
drivers/clk/bcm/clk-kona.c
These implement the basic Kona clock functionality,
including the clk_ops methods and various routines to
manipulate registers and interpret their values. This
includes some functions used to set clocks to a desired
initial state (though this feature is only partially
implemented here).
drivers/clk/bcm/clk-kona-setup.c
This contains generic run-time initialization code for
data structures representing Kona CCUs and clocks. This
encapsulates the clock structure initialization that can't
be done statically. Note that there is a great deal of
validity-checking code here, making explicit certain
assumptions in the code. This is mostly useful for adding
new clock definitions and could possibly be disabled for
production use.
drivers/clk/bcm/clk-bcm281xx.c
This file defines the specific CCUs used by BCM281XX family
SoCs, as well as the specific clocks implemented by each.
It declares a device tree clock match entry for each CCU
defined.
include/dt-bindings/clock/bcm281xx.h
This file defines the selector (index) values used to
identify a particular clock provided by a CCU. It consists
entirely of C preprocessor constants, to be used by both the
C source and device tree source files.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
- mvebu (Armada 375/380/385)
- extend corediv clock driver to support new SoCs
- add core and gating clock drivers for new SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Aah7
-----END PGP SIGNATURE-----
Merge tag 'clk-mvebu-3xx-3.15' of git://git.infradead.org/linux-mvebu into clk-next-mvebu
clock: mvebu new SoC changes for v3.15
- mvebu (Armada 375/380/385)
- extend corediv clock driver to support new SoCs
- add core and gating clock drivers for new SoCs
ux500_twocell_get is a local symbol.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
tegra_clk_periph_no_gate_ops is a local symbol.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a property called clock-indices to allow clock-output-names
to be used where the index used to lookup a clock is not a 1:1
mapping to the array position in the clock-output-names
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Tegra124 does not have gr2d and gr3d clocks. They have been replaced by the
vic03 and gpu clocks respectively.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The lb, qspi, sdh, sd0 and sd1 clocks have the PLL1 (divided by 2) as
their parent, not the main clock. Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clk-phase property is used to represent the 2 clock phase values that is
needed for the SD/MMC driver. Add a prepare function to the clk_ops, that will
use the syscon driver to set sdmmc_clk's phase shift that is located in the
system manager.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
---
v9: none
v8: Use degrees in the clk-phase binding property
v7: Add dts property to represent the clk phase of the sdmmc_clk. Add a
prepare function to the gate clk that will toggle clock phase setting.
Remove the "altr,socfpga-sdmmc-sdr-clk" clock type.
v6: Add a new clock type "altr,socfpga-sdmmc-sdr-clk" that will be used to
set the phase shift settings.
v5: Use the "snps,dw-mshc" binding
v4: Use the sdmmc_clk prepare function to set the phase shift settings
v3: Not use the syscon driver because as of 3.13-rc1, the syscon driver is
loaded after the clock driver.
v2: Use the syscon driver
Move the different kinds of clocks into their own files. The reason is to aid
readability of the code. This also goes along with the other SoC-specific
clock drivers.
The split introduces new structs for the three types of clocks and uses them.
Other changes are not done to the code.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The clk_name field from the socfpga_clk struct is unused.
Remove it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The only thing that socfpga_init_clocks was doing is setting up the smp_twd clk.
Now that twd-timer's clock phandle is populated in the DTS, we can remove
this function.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
After the patch:
"clk: socfpga: Map the clk manager base address in the clock driver"
The clk->name field in socfpga_clk_recalc_rate() was getting cleared. Replace
looking for the GPIO_DB_CLK by its divider offset instead.
Also rename the define SOCFPGA_DB_CLK_OFFSET -> SOCFPGA_GPIO_DB_CLK_OFFSET, as
this represents the GPIO_DB_CLK.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The clk manager's base address was being mapped in SOCFPGA's arch code and
being extern'ed out to the clock driver. This method is not correct, and the
arch code was not really doing anything with that clk manager anyways.
This patch moves the mapping of the clk manager's base address in the clock
driver itself. Cleans up CLK_OF_DECLARE() into a single registration of all
the clocks.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
v2: Use a static declaration for the clk_mgr_base_addr. Clean up the
CLK_OF_DECLARE() as suggested by Arnd.
Contradicting to documenation, the notifier callbacks do receive
the original clock rate in struct clk_notifier_data.old_rate and the new
frequency struct clk_notifier_data.new_rate, independent of the
notification reason.
This behavior also seems to make more sense, since callbacks can use the
same code to deterimine whether clocks are scaled up or down. Something
which would not even possible in the post-rate-change case if the
behavior was as documented.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the clock driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A20/A31 clock module controls the transmit clock source
and interface type of the GMAC ethernet controller. Model this as
a single clock for GMAC drivers to use.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The A31 has a slightly different PLL6 clock. Add support for this new clock in
our driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Add register definitions for the usb-clk register found on sun4i, sun5i and
sun7i SoCs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The usb-clk register is special in that it not only contains clk gate bits,
but also has a few reset bits. This commit adds support for this by allowing
gates type sunxi clks to also register a reset controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
When requesting a rate less than the minimum clock rate for a divider,
use the maximum divider value instead of bailing out with an error.
This matches the behavior of the generic clock divider.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
When pll_x is the parent of cclk_lp, PLLX_DIV2_BYPASS_LP determines
whether cclk_lp output is divided by 2. Set TEGRA_DIVIDER_2 so that
the clk_super driver is aware of this.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The sdmmc clocks on Tegra114 and Tegra124 are 3-bit wide muxes with
6 parents. Add support for tegra_clk_sdmmc*_8 and switch Tegra114
and Tegra124 to use these clocks instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The host1x clock on Tegra124 is a 3-bit wide mux with 6 parents.
Change thte id to tegra_clk_host1x_8 so that the correct clock gets
registered.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Set correct pll_d2_out0 divider and correct the p div values for pll_d2.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
PLLD was using the same mnp table as PLLP. Fix it to use its own
table which is different from PLLP's.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
This table had settings for 216MHz, but PLLP is (and is supposed to be)
configured at 408MHz. If that table is used and PLLP_BASE_OVRRIDE is
not set, the kernel will panic in clk_pll_recalc_rate().
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Add clocks required for accessing fuses on Tegra20.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add the clock support for the new SoCs Armada 380 and Armada 385:
core clocks and gating clocks.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the clock support for the new SoC Armada 375: core clocks and
gating clocks.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds support for the Core Divider clocks of the Armada
375. Compared to Armada 370 and XP the Core Divider clocks of the 375
cannot be gated: only their ratio can be changed. This is reflected by
the fact that the enable, disable and is_enabled clock operations are
not defined, and that the enable_bit_offset field is also undefined.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit refactors the corediv clock driver so that it is capable
of handling various SOCs that have slightly different corediv clock
registers and capabilities.
It introduces a clk_corediv_soc_desc structure that encapsulates all
the SoC specific details.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As of now, part of Exynos4 clock suspend/resume handling is located
in mach-exynos/pm.c, which is not where code accessing CMU registers
should reside.
This patch implements all the necessary suspend/resume handling code
in Exynos4 clock driver to allow dropping that old code.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since all SoC drivers have been moved to local suspend/resume handling,
the old code can be safely dropped.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there are multiple differences in how suspend/resume of particular
Exynos SoCs must be handled, SoC driver is better place for
suspend/resume handlers and so this patch moves them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there are multiple differences in how suspend/resume of particular
Exynos SoCs must be handled, SoC driver is better place for
suspend/resume handlers and so this patch moves them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there are multiple differences in how suspend/resume of particular
Exynos SoCs must be handled, SoC driver is better place for
suspend/resume handlers and so this patch moves them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since there are multiple differences in how suspend/resume of particular
Exynos SoCs must be handled, SoC driver is better place for
suspend/resume handlers and so this patch moves them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As suspend/resume handlers are being moved to SoC specific code, due to
differencies in suspend/resume handling of particular SoCs, to minimize
code duplication this patch provides common register save/restore
helpers that save/restore given list of registers of clock controller.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch simplifies a bit clock initialization code by removing
remnants of non-DT clock initialization, such as reg_base and xom values
passed in function parameters.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If the ICST clock has a parent, respect the rate of the parent
when calculating the clock frequency. As this involves modifying
the ICST parameter struct, make a cloned copy (the divisor
arrays should be safe) so we can update the .ref field.
Do not define the reference clock on the Integrator as we have
the reference clock from the device tree. Keep it everywhere
else.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want to actually define the parent frequency in the device
tree for the ICST clocks, modify the clock registration function
to take a parent argument.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This atomic commit changes the Integrator clock implementation
and the machines to register clocks from the device tree and
use these instead of the previous hard-coded clocks.
In the clock implementation all hard-coded clocks and the
special initialization function call goes away, and is
replaced by two compatible strings for the two clocks
available on the core module.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clk_init_data struct is allocated in the stack. All members of
this struct should be initialized before using otherwise it will
lead to unpredictable situation as it can contain garbage.
Ultimately the clk->flag field contains garbage. In my case it leads
that flag CLK_IGNORE_UNUSED is set for most of clocks. As result a
bunch of unused clocks cannot be disabled.
So initialize flags in this structure too.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The clkc has its registers in the range of the slcr.
Instead of passing around the slcr base address pointer, let the clkc get the
address from the DT.
This prepares the slcr to be a real driver with multiple memory ranges
(slcr, clocks, pinctrl,...)
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Divs clocks consist of a parent factor clock with multiple outputs,
and seperate clocks for each output. Get the name of the parent
clock from the parent factor clock, instead of the DT node name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Some factor clocks, such as the parent clock of pll5 and pll6, have
multiple output names. Add the corresponding names to factors_data
tied to compatible string.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
sunxi clock drivers use dt node name as clock name, but clock
nodes should be named clk@X, so the names would be the same.
Let the drivers read clock names from dt clock-output-names
property.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for Samsung
chips. Additionally there are other smaller clock driver changes and
several last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRJD
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
Currently, we are allocating space for two pointers, when we actually
may need to store three of them (two divisors plus the original clock).
Fix this, and change sizeof(type) to sizeof(*var) to keep checkpatch.pl
happy.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Allow drivers to be compiled as modules by exporting more clock
provider functions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit 9807362bfe
"clk: si5351: declare all device IDs for module loading"
removed the common i2c_device_id and introduced new ones for each variant
of the clock generator. Instead of exploiting that information in the driver,
it still depends on platform_data passing the chips .variant.
This removes the now redundant .variant from the platform_data and puts it in
i2c_device_id's .driver_data instead.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
entirely of new platform/driver support. There are some conversions of
existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc tree
this pull request is broken into two pieces. The second piece will be
sent out after arm-soc sends you the pull request that merged in core
support for the HiSilicon 3620 platform. That same pull request from
arm-soc depends on this pull request to merge in those HiSilicon bits
without causing build failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Hh66
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they came in
quite late and we decided to keep them deferred until the first -stable
release to get more coverage instead of squeezing them into 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QhN9
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
Semicolon not needed after switch statement.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
According to Documentation/kbuild/makefiles.txt these symbols
should be clk-qcom-y. Otherwise the build will fail if
CONFIG_COMMON_CLK_QCOM=m. Fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-43xx.c now contains the clock init functionality for am43xx, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-7xx.c now contains the clock init functionality for dra7, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch adds support for DRA7 PCIe APLL. The APLL
sources the optional functional clocks for PCIe module.
APLL stands for Analog PLL. This is different when comapred
with DPLL meaning Digital PLL, the phase detection is done
using an analog circuit.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
USB_DPLL must be initialized and locked at boot so that
USB modules can work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-54xx.c now contains the clock init functionality for omap5, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-44xx.c now contains the clock init functionality for omap4, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti,mux-clock provides now a binding for basic mux support. This is just
using the basic clock type.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some OMAP clocks require knowledge about their parent clockdomain for
book keeping purposes. This patch creates a new DT binding for TI
clockdomains, which act as a collection of device clocks. Clockdomain
itself is rather misleading name for the hardware functionality, as at
least on OMAP4 / OMAP5 / DRA7 the clockdomains can be collections of either
clocks and/or IP blocks, thus idle-domain or such might be more appropriate.
For most cases on these SoCs, the kernel doesn't even need the information
and the mappings can be ignored.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI specific gate clocks. These behave as basic
gate-clock, but have different ops / hw-ops for controlling the actual
gate, for example waiting until the clock is ready. Several sub-types
are supported:
- ti,gate-clock: basic gate clock with default ops/hwops
- ti,clkdm-gate-clock: clockdomain level gate control
- ti,dss-gate-clock: gate clock with DSS specific hardware handling
- ti,am35xx-gate-clock: gate clock with AM35xx specific hardware handling
- ti,hsdiv-gate-clock: gate clock with OMAP36xx hardware errata handling
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This behaves exactly in similar manner to basic fixed-factor-clock, but
adds a few properties on top for handling clock hardware autoidling.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI divider clock binding, which simply uses
the basic clock divider to provide the features needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti_dt_clk_init_provider() can now be used to initialize the contents of
a single clock IP block. This parses all the clocks under the IP block
and calls the corresponding init function for them.
This patch also introduces a helper function for the TI clock drivers
to get register info from DT and append the master IP info to this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some devices require their clocks to be available with a specific
dev-id con-id mapping. With DT, the clocks can be found by default
only with their name, or alternatively through the device node of
the consumer. With drivers, that don't support DT fully yet, add
mechanism to register specific clock names.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM8660
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the multimedia clock controller found on MSM
8960 based platforms. This should allow multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM8960
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Reset controllers and clock controllers are combined into one IP
block on Qualcomm chipsets. Usually a reset signal is associated
with each clock branch but sometimes a reset signal is associated
with a handful of clocks. Either way the register interface is
the same; set a bit to assert a reset and clear a bit to deassert
a reset. Add support for these types of resets signals.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for Qualcomm's PLLs (phase locked loops). This is
sufficient enough to be able to determine the rate the PLL is
running at. We can add rate setting support later when it's
needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of Qualcomm's clocks can change their parent and rate at the
same time with a single register write. Add support for this
hardware to the common clock framework by adding a new
set_rate_and_parent() op. When the clock framework determines
that both the parent and the rate are going to change during
clk_set_rate() it will call the .set_rate_and_parent() op if
available and fall back to calling .set_parent() followed by
.set_rate() otherwise.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
sirfprima2 and sirfatlas6 are two different SoCs in CSR SiRF series. for
prima2 and atlas6, there are many shared clocks but there are still
some different register layout and hardware clocks, then result in
different clock table.
here we re-arch the driver to
1. clk-common.c provides common clocks for prima2 and atlas6,
2. clk-prima2.h describles registers of prima2 and clk-prima2.c provides
prima2 specific clocks and clock table.
3. clk-atlas6.h describles registers of atlas6 and clk-atlas6.c provides
atlas6 specific clocks and clock table.
4. clk.h and clk.c expose external interfaces and provide uniform entry
for both prima2 and atlas6.
so both prima2 and atlas6 will get support by drivers/clk/sirf.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The composite clock's .determine_rate implementation can call the
underyling .determine_rate callback corresponding to rate_hw or the
underlying .determine_rate callback corresponding to mux_hw. In both
cases we pass in rate_hw, which is wrong. Fixed by passing mux_hw into
the correct callback.
Reported-by: Lemon Dai <dailemon.gl@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSzV2DAAoJEAf03oE53VmQLl0H/2KFQx+lwcg1XWd6Sq05yW7h
PtVKT6bCNZxDXGiUZ1mvZLBkDlVoQn7p35gX+NM05rsad8t9ibdmEutpe4ynPohc
Es5UpQ20txhpzGoDiIIW+pWng+fajtMV1dV8xEC4pf/d4K7HSH8k/tUwZ4GrtaJb
4eUyohznKBHdroavXao1aIuvM+MJvIu2qvxCZZPYDp0LBzTxlHR+ogcCcqO80YSL
dHG2WzbGLr+XMkxpl0bJMF9bxYarg0NsHk+GPqmnOI479rNevptSncbLQRchvwGD
auEAN8I77IwQGUpTuupssKgUrSbOU9JHTwiC2pv8zkaKdoYaIBQVPXCvmyV6kAk=
=KYgN
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
Second cleanup pull-request for 3.14:
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
* tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91:
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The clks member of the clk_onecell_data structure should
point to a valid clk array (no NULL entries allowed),
and the clk_num should be equal to the number
of elements in the clks array.
The MSTP driver fails to satisfy the above conditions.
The clks array may contain NULL entries if not all
clock-indices are initialized in the device tree.
Thus, if the clock indices are interleaved we end up
with NULL pointers in-between.
The other problem is the driver uses maximum clock index
as the number of clocks, which is incorrect (less than
the actual number of clocks by 1).
Fix the first issue by pre-setting the whole clks array
with ERR_PTR(-ENOENT) pointers instead of zeros; and
use maximum clkidx + 1 as the number of clocks to fix
the other one.
This should make of_clk_src_onecell_get() return the following:
* valid clk pointers for all clocks registered;
* ERR_PTR(-EINVAL) if (idx >= clk_data->clk_num);
* ERR_PTR(-ENOENT) if the clock at the selected index was not
initialized in the device tree (and was not registered).
Changes in V2:
* removed brackets from the one-line for loop
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use clkidx when registering MSTP clocks instead of loop counter
since the value is then used to access the specific clock index bit
in the mstp register.
The issue was introduced by the following commit:
f94859c215 "clk: shmobile: Add MSTP clock support"
Changes in V2:
* none
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If max77686 chip is instantiated from device tree, it is desirable to
have an OF clock provider to allow device tree based look-up of clocks.
This patch adds OF clock provider registration to the clk-max77686
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a prerequisite for further patch adding OF clock provider support to
the driver, this patch changes the driver to store an array of struct
clk * as driver data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch fixes invalid kfree() and adds missing call to clk_unregister()
in error and remove paths in max77686_clk_probe(). While at it, error
handling is also cleaned up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a preparation for further patches, this patch modifies the clock
registration helper function to return a pointer to the newly registered
clock. No functional change is done to the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The function can simply return 0, without jumping to a separate label,
which does exactly the same. This patch does not introduce any
functional change, just a clean-up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is usually nice to know frequency of a clock, so this patch adds a
.recalc_rate() callback returning rates of provided clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Changing status of clock gates in max77686 requires i2c transfers, which
can sleep, so this is done in prepare and unprepare callbacks. Due to
this, checking whether whether the clock is ungated must be done
in is_prepared() callback as well, for consistency.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The AudioSS block on Exynos 5420 has an additional clock gate for the
ADMA bus clock.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
There is no gate for the PCM clock input to the AudioSS block, so
the parent of sclk_pcm is div_pcm0. Add a clock ID for it so that
we can reference it in device trees.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This allows the input clocks to the Exynos AudioSS block to be
specified via device-tree bindings. Default names will be used
when an input clock is not given.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The Exynos AudioSS clock controller will later be modified to allow
input clocks to be specified via device-tree in order to support
multiple Exynos SoCs. This will introduce a dependency on the core
SoC clock controller being initialized first so that the AudioSS driver
can look up its input clocks, but the order in which clock providers
are probed in of_clk_init() is not guaranteed. Since deferred probing
is not supported in of_clk_init() and the AudioSS block is not the core
controller, we can initialize it later as a platform device.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Register the APLL rate table so that we can set the APLL rate from
the cpufreq driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Commit 6d9252bd9a (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0B0x
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
Register both VCO clocks, give per-logical module unique names
to the clocks so we can have several IM-PD1's connected (in
theory). Implement all the fixed-factor clocks as children of
VCO2.
Tested by using the UARTs and the PL181 MMC block on the IM-PD1,
works flawlessly.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we have more than one of these clocks in a system (such as
on the IM-PD1) we need a mechanism to pass a name for the clock.
Refactor to add this as an argument.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add CLK_SET_RATE_PARENT flag to mout_apll clock. This will let us set the
clock rate in the cpufreq driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mout_aclk333_sub mux clock and updates gate clocks from
MFC domain to have it as their parent as specified in SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
According to SoC documentation, input 5 of mout_audio muxes is connected
to xxti (named fin_pll in the driver). This patch corrects defined
parent arrays to match SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch updates mux parent arrays with unpopulated mux inputs, as all
inputs need to be specified in parent arrays passed to
clk_register_mux(), otherwise clk_set_parent() can generate out of bound
accesses to the array.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mux_aclk_200_disp1_sub mux clock, which according to SoC
documentation is the correct parent of DISP1 gate clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mout_aclk266_gscl_sub mux clock and adjusts definitions
of GSCL domain gate clocks to use it as their parent, as specified in
SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch renames all mux clocks to start with mout_ prefix and all div
clocks to start with div_ prefix for consistency with other clocks
already defined this way.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch reorders clock definitions, so they are sorted by register
addresses and bitfield shifts. When at it, blank lines are added to
separate definitions of clocks from different registers.
Overall this should make the driver more readable and reduce the number
of potential conflicts when adding new entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Move reg_save[] into CONFIG_PM_SLEEP dependency block as it is used only
by suspend and resume functions.
This fixes the warning on CONFIG_PM_SLEEP=n:
drivers/clk/samsung/clk-exynos-audss.c:29:22: warning: ‘reg_save’ defined but not used [-Wunused-variable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The sysreg (system register) generates control signals for various blocks
like disp1blk, i2c, mipi, usb etc. However, it gets disabled as an unused
clock at boot-up. This can lead to failures in operation of above blocks,
because they can not be configured properly if this clock is disabled.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Adds gate clock for MDMA0 on Exynos5250 SoC. This is needed to ensure
that the clock is enabled when MDMA0 is used on systems on which
firmware gates the clockby default.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The CLK_GATE_IP_ACP register offset is incorrectly listed making
definition of g2d clock incorrect, which may lead to system failures
when trying to use G2D on systems on which firmware gates this clock
by default. Fix this and the register ordering as well.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The gate clocks for the MFC sysmmus appear to be flipped, i.e.
GATE_IP_MFC[2] gates sysmmu_mfcl and GATE_IP_MFC[1] gates sysmmu_mfcr.
Fix this so that the MFC will start up.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The SRC_MFC register offset was incorrect, which could cause have caused
wrong calculation of rate of sclk_mfc clock, that could in turn lead to
incorrect operation of MFC. This patch corrects it.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Allwinner sunXi SoCs clock changes
This contains the clk driver parts of the "[PATCH v3 00/13] clk: sunxi:
add PLL5 and PLL6 support" series. It adds support for PLL4/5/6 and
mod0 clocks on most sunxi platforms. Additionally, it contains "[PATCH
1/4] clk: sunxi: Allwinner A20 output clock support" (v2) from Chen-Yu
Tsai, which adds support for output clocks present on A20.
This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
The DT nodes should look like
abc_clk: clk@deadbeef {
...
clock-output-names = "abc";
}
But our old DT nodes look like
abc: abc@deadbeef {
...
}
So, let's support both formats, until we can transition everything
to the new, correct one.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
We will be needing this to register a factor clock as parent with leaf
divisors on a single call.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
This was pointed out during the review of the factor patches. Let's
indicate what does that magic 5 mean.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit reworks factors clock registration to be done behind a
composite clock. This allows us to additionally add a gate, mux or
divisors, as it will be needed by some future PLLs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Populate ${DEBUGS_MOUNT_POINT}/clk if CONFIG_DEBUG_FS is set. This
eliminates the extra (annoying) step of enabling the config option
manually.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'break' after 'goto' is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YqMd
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
ARM: dts: Disable I2C controllers by default on Exynos5250
ARM: dts: Leave Exynos5250 SPI controller disabled by default
ARM: dts: Add CODEC MCLK for SMDK5250
ARM: dts: Add device nodes for TMU blocks for exynos5420
ARM: dts: Fix status property of mmc nodes for snow board
ARM: dts: Fix missing spaces after labels for exynos
ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
ARM: dts: Move MCT node to exynos4x12.dtsi
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
Documentation: devicetree: Update Exynos MCT bindings description
ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
ARM: dts: Add SPI nodes to the exynos5420 device tree file
ARM: dts: Add DMA controller node info on Exynos5420
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
ARM: dts: Fix exynos5250-snow's search key to be L_META
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock accuracy is expressed in ppb (parts per billion) and represents
the possible clock drift.
Say you have a clock (e.g. an oscillator) which provides a fixed clock of
20MHz with an accuracy of +- 20Hz. This accuracy expressed in ppb is
20Hz/20MHz = 1000 ppb (or 1 ppm).
Clock users may need the clock accuracy information in order to choose
the best clock (the one with the best accuracy) across several available
clocks.
This patch adds clk accuracy retrieval support for common clk framework by
means of a new function called clk_get_accuracy.
This function returns the given clock accuracy expressed in ppb.
In order to get the clock accuracy, this implementation adds one callback
called recalc_accuracy to the clk_ops structure.
This callback is given the parent clock accuracy (if the clock is not a
root clock) and should recalculate the given clock accuracy.
This callback is optional and may be implemented if the clock is not
a perfect clock (accuracy != 0 ppb).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'clk_si570_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for using emev2 SMU clocks with DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NhhY
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into clk-next-shmobile2
Renesas ARM based SoC Clock updates for v3.14
Add support for using emev2 SMU clocks with DT
The clock was missing CLK_SET_RATE_PARENT flag, which caused rate
setting failures due to inability of reconfiguration of second
divider behind it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extra semicolon is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'vtwm_pll_ops' is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'of_cpu_clk_setup' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_sp810_timerclken_of_get is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
tegra_clk_periph_nodiv_ops is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_frac_ops is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix pmc_clk_ids data type attribute (__initdata -> __initconst).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix building of s2mps11 regulator and clock drivers after renaming
regmap field in struct sec_pmic_dev in commit:
- "mfd/rtc: s5m: Fix register updating by adding regmap for RTC"
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This AT91 specific Kconfig option removed the code that dealt with
programmable clocks. Each AT91 SoC embeds programmable clocks and
there is little gain to remove this code in case that such a clock
is not used.
If this option is not selected, it causes certain drivers to fail
to build. We simply remove this option instead of adding code just
to build a workaround.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The "pcie_xclk" clock is not actually a clock at all, but rather a reset
domain. Now that the custom Tegra module reset API has been removed, we
can remove the definition of any "clocks" that existed solely to support
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch fixes Keystone gate control clock driver initialization path:
1) clk_register_psc() returns error code and not a pure pointer, hence
its return value need to be checked using IS_ERR(clk) macro.
2) Mapped IO memory isn't unmapped in case of errors, hence fix it.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.
Also update the Documentation of bindings to reflect the same.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Fixes cpll control and lock register offset values for Exynos5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_unregister() is currently not implemented and it is required when
a clock provider module needs to be unloaded.
Normally the clock supplier module is prevented to be unloaded by
taking reference on the module in clk_get().
For cases when the clock supplier module deinitializes despite the
consumers of its clocks holding a reference on the module, e.g. when
the driver is unbound through "unbind" sysfs attribute, there are
empty clock ops added. These ops are assigned temporarily to struct
clk and used until all consumers release the clock, to avoid invoking
callbacks from the module which just got removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds common __clk_get(), __clk_put() clkdev helpers that
replace their platform specific counterparts when the common clock
API is used.
The owner module pointer field is added to struct clk so a reference
to the clock supplier module can be taken by the clock consumers.
The owner module is assigned while the clock is being registered,
in functions _clk_register() and __clk_register().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is currently a race condition in the device tree part of clk_get()
function, since the pointer returned from of_clk_get_by_name() may become
invalid before __clk_get() call. E.g. due to the clock provider driver
remove() callback being called in between of_clk_get_by_name() and
__clk_get().
Fix this by doing both the look up and __clk_get() operations with the
clock providers list mutex held. This ensures that the clock pointer
returned from __of_clk_get_from_provider() call and passed to __clk_get()
is valid, as long as the clock supplier module first removes its clock
provider instance and then does clk_unregister() on the corresponding
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add helper functions for the of_clk_providers list locking and
an unlocked variant of of_clk_get_from_provider().
These functions are intended to be used in the clkdev to avoid
race condition in the device tree based clock look up in clk_get().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch adds at91 smd (Soft Modem) clock implementation using common clk
framework.
Not used by any driver right now.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 usb clock implementation using common clk framework.
This clock is used to clock usb ports (ohci, ehci and udc).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds new at91 utmi clock implementation using common clk framework.
This clock is a pll with a fixed factor (x40).
It is used as a source for usb clock.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 programmable clocks implementation using common clk
framework.
A programmable clock is a clock which can be exported on a given pin to clock
external devices.
Each programmable clock is given an id (from 0 to 8).
The number of available programmable clocks depends on the SoC you're using.
Programmable clock driver only implements the clock setting (clock rate and
parent setting). It must be chained to a system clock in order to
enable/disable the generated clock.
The PCKX pins used to output the clock signals must be assigned to the
appropriate peripheral (see atmel's datasheets).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 peripheral clock implementation using common clk
framework.
Almost all peripherals provided by at91 SoCs need a clock to work properly.
This clock is enabled/disabled using PCER/PCDR resgisters.
Each peripheral is given an id (see atmel's datasheets) which is used to
define and reference peripheral clocks.
Some new SoCs (at91sam9x5 and sama5d3) provide a new register (PCR) where you
can configure the peripheral clock as a division of the master clock.
This will help reducing the peripherals power comsumption.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 system clock implementation using common clk
framework.
Some peripherals need to enable a "system" clock in order to work properly.
Each system clock is given an id based on the bit position in SCER/SCDR
registers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 master clock implementation using common clk
framework.
The master clock layout describe the MCKR register layout.
There are 2 master clock layouts:
- at91rm9200
- at91sam9x5
Master clocks are given characteristics:
- min/max clock output rate
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 pll clock implementation using common clk framework.
The pll clock layout describe the PLLX register layout.
There are four pll clock layouts:
- at91rm9200
- at91sam9g20
- at91sam9g45
- sama5d3
PLL clocks are given characteristics:
- min/max clock source rate
- ranges of valid clock output rates
- values to set in out and icpll fields for each supported output range
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 main oscillator clock implementation using common
clk framework.
If rate is not provided during clock registration it is calculated using
the slow clock (main clk parent in this case) rate and MCFR register.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds at91 PMC (Power Management Controller) base support.
All at91 clocks managed by the PMC unit will use this framework.
This framework provides the following fonctionalities:
- define a new struct at91_pmc to hide PMC internals (lock, PMC memory
mapping, irq domain, ...)
- read/write helper functions (pmc_read/write) to access PMC registers
- lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to
pmc registers
- a new irq domain and its associated irq chip to request PMC specific
interrupts (useful for clk prepare callbacks)
The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every
clk using this framework will declare a table of of_at91_clk_init_cb_t
and add it to the pmc_clk_ids table.
When the pmc dt clock setup function is called (by of_clk_init function),
it triggers the registration of every supported child clk (those matching
the definitions in pmc_clk_ids).
This patch copies at91_pmc_base (memory mapping) and at91sam9_idle
(function) from arch/arm/mach-at91/clock.c (which is not compiled if
COMMON_CLK_AT91 is enabled).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sWyX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-3.13' of https://github.com/mripard/linux into clk-next-sunxi-rebase
Allwinner sunXi SoCs clock changes
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
Conflicts:
drivers/clk/sunxi/clk-sunxi.c
In case of error, the function __clk_lookup() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
clk_round_rate() can be used by drivers to determine whether or not a
frequency is supported by the clock. The current Tegra clock driver
outputs an error message and a stacktrace when the requested rate isn't
supported. That's fine for clk_set_rate(), but it's confusing when all
the driver does is query whether or not a frequency is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function socfpga_clk_init() can support clocks that do not have a divider
register, but a fixed-divider that can be read from DTS. Therefore, the "reg"
property is not a failing condition for socfpga_clk_init().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[Maybe the third time will be the charm. -Alex]
If CONFIG_COMMON_CLK_DEBUG is defined, clk_debug_create_one() is
called to populate a debugfs directory with a few entries that are
common for all clock types.
If an error happens after creating the first one debugfs_remove() is
called on the clock's directory. The problem with this is that no
cleanup is done on the debugfs files already created in that
directory, so the directory never actually gets removed. This
problem is silently ignored.
Fix this by calling debugfs_remove_recursive() instead. Reset the
clk->dentry field to null afterward, to ensure it can't be mistaken
as a valid pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock for the PWM controller is slightly different from other
peripheral clocks on Tegra30. The clock source mux field start at
bit position 28 rather than 30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two GPUs on Tegra30 and each of them uses a separate clock, so
the secondary clock needs to be initialized in order for the gr3d module
to work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add disp1 and disp2 clocks to the clock initialization table. These
clocks are required for display and HDMI support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Hook the functions for CPU hotplug support. After the CPU is hot
unplugged, the flow controller will handle to clock gate the CPU clock.
But still need to implement an empty function to avoid warning message.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tegra124 introduces a number of new peripheral clocks. This patch adds those
to the common peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 introduces a number of a new clocks. Introduce the corresponding
the IDs for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 has a clock which consists of a mux and a fractional divider.
Add support for this.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has periph clocks which share the hw register. Hence locking is
required.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a common function which performs super clock initialization for
Tegra114 and beyond.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce new files for fixed and PMC clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a new file for peripheral clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure. Also PLLP and the PLLP_OUT
clocks will be initialized here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move audio clocks and PLLA initialization to a common file so it can be used by
multiple Tegra SoCs. Also a new array tegra114_clks is introduced for Tegra114
which specifies which common clocks are available on Tegra114 and what their
DT IDs are.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add a common infra for registering clkdev. This allows decoupling clk
registration from clkdev registration.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Many clocks are common between several Tegra SoCs. Define an enum to list
them so we can move them to separate files which can be shared between
SoCs. Each SoC specific file will provide an array with the common clocks
which are present on the SoC and their DT binding ID.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move some fields related to the PLL HW description to the tegra_clk_pll_params.
This allows some PLL code to be moved to common files later.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Use pll_ref instead of pll_re_vco as the pll_e parent on Tegra114. Also
add a 12Mhz pll_ref table entry for pll_e for Tegra114. This prevents
the system from crashing at bootup because of an unsupported pll_re_vco
rate.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
VCO min clipping, dynamic ramp setup and IDDQ init can be done in the
respective PLL clk_register functions if the parent is already registered.
This is done for other some PLLs already.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This flag indicates the peripheral clock does not have a divider. It will
simplify the initialization tables and avoids some very similar code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch makes periph_clk_enb_refcnt a global array, dynamically allocated
at boottime. It simplifies the macros somewhat and allows clocks common to
several Tegra SoCs to be defined in a separate files. Also the clks array
becomes global and dynamically allocated which allows the DT registration to
be moved to a generic funcion.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The PLL output frequency is multiplied during the P-divider computation,
so it needs to be divided by the P-divider again before returning.
This fixes an issue where clk_round_rate() would return the multiplied
frequency instead of the real one after the P-divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The power-on default parent for this clock is pll_m, which turns out to
be wrong. Previously, bootloader reparented this clock. We'll do it in
the kernel as well, so that there's one less thing that we depend on
bootloader to initialize.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Perform upwards rounding when calculating dividers for periph clks on Tegra30
and Tegra114.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
pll_m will be the parent of gr2d/gr3d if we don't do this.
And because pll_m runs at a high rate so gr2d/gr3d will be
unstable. So change the parent of them to pll_c2.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
In Tegra114, vde/gr_2d/gr_3d have 3 bits for clock source selection.
So change the clock init macro for these clocks from
"TEGRA_INIT_DATA_INT" to "TEGRA_INIT_DATA_INT8".
Besides, no one uses "TEGRA_INIT_DATA_INT" after this change, so
remove this macro.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra114 sbc1-sbc6 have more possible parent clocks than Tegra30.
So correct the parents and mux width for them.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
As the clock IDs are now specified in a header file, we can use those
definitions instead of maintaining an internal enum.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This commit introduces a new group of clocks present in Armada 370/XP
SoCs (called "Core Divider" clocks) and add a provider for them.
The only clock supported for now is the NAND clock (ndclk), but the
infrastructure to add the rest is already set.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since the old DMA driver got removed, these aliases are no longer
necessary.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds clkdev aliases for clocks used by PL08x DMA driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
