In the past, all the MMC pins had
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.
Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The pin controllers also use the two oscillators for debouncing. Add them
to the DTs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A31 SoC includes the Allwinner audio codec, capable of 24-bit
playback up to 192 kHz and 24-bit capture up to 48 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LCD0 controller on the A31 can do RGB output up to 8 bits per
channel. Add the pins for RGB888 output.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a different clock representation, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 and mmc3 are available on the same pins, with different mux values.
However, only mmc3 supports 8 bit DDR transfer modes.
Since preference for mmc3 over mmc2 is due to DDR transfer modes, just
set the drive strength to 40mA, which is needed for DDR.
This pinmux setting also includes the hardware reset pin for emmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.
Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun6i also has the LRADC for tablet buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
A31/A31s have the same "Security System" crypto engine as A10/A20,
but with a separate reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The A31 gates have a non continuous set of clock IDs that are valid. Add
the clock-indices property to the DT to express this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The current DTs were setting the cell size to 2, but used the default xlate
function that was assuming an interrupt cell size of 1, leading to the
second part of the cell (the flags) being ignored, while we were having an
inconsistent binding between the interrupts and gpio (that could also be
used as interrupts).
That "binding" doesn't work either with newer SoCs that have multiple irq
banks.
Now that we fixed the pinctrl driver to handle this like it should always
have been handled, convert the DT users, and while we're at it, remove the
size-cells property of PIO that is completely useless.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add a node for the otg/drc usb controller to sun6i-a31.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines (probably copy pasted) have an indentation mixing tabs and
spaces that triggers a checkpatch warning.
Fix those, and while we're at it, fix the space-indented sections.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines in our DTSIs are over the 80 characters limit, making
checkpatch complain about that.
If possible (and relevant), wrap these lines to 80 characters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On sun6i we already have PLL6 as AHB1 clock's parent. However this was
previously set in the dma controller node, which takes effect when the
dma controller is probed.
We want this to take effect as soon as possible, so hrtimer rate
calculation is correct, and to be sure the AHB1 clock rate remains as
stable as possible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the a list compiled by Maxime Ripard,
which is based on A31 FEX files from the sunxi-boards repository. Not all
boards have the same settings. The settings in this patch are the ones
shared by A/B/C revisions, plus the default clock setting from u-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc1 is used to connect to the WiFi chip on the Hummingbird A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[maxime: Changed the drive and pull values for their defines]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Sometimes we need to specify non-probably information for sdio devices in the
devicetree, this is done through child nodes addressed by the reg property,
whereby the reg property refers to the sdio function number, see;
Documentation/devicetree/bindings/mmc/mmc.txt
This commit adds the necessary address- and size-cells properties to the mmc
controller nodes in the dtsi files, so that dts files needing such a child
node do not need to specify these themselves.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The p2wi controller has only one possible pinmux setting. Use it by
default in the dtsi, instead of having to set it in each board's dts.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: reformat commit title; rename p2wi pins and use as default]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
Commit f77d55a3b5 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support the sun6i variant of the touchscreen controller,
add the device node to the dtsi so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has non-initialized architected timers, without CNTFRQ or CNTVOFF set
by the Allwinner's bootloader.
Use the new DT property for such case, and enable the arch timers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GIC requires some extra opaque arguments to set the IRQ type and flags.
Convert the DTs to using the common defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the ir receiver found on the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an ir_clk sub-node to the prcm node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the sample and output clocks for the MMC phase support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
The clock driver has unified support for the ahb1 clock.
Unify the clock nodes so it works.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
much later than usual due to several last minute bugs that had to be
addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future which
will better parition clock providers from clock consumers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jD84
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.
Instead a platform specific compatible + properties should be used for this.
The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
