The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On carl9170, HW encryption is disabled on IBSS; the mac80211
software-based encryption is used instead. As mac80211 supports IBSS
RSN (per-STA GTK), claim its support in the carl9170 PHY.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function is called with locks held and thus should not use GFP_KERNEL.
The semantic patch that makes this report is available
in scripts/coccinelle/locks/call_kern.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase NCI deactivate timeout from 5 sec to 30 sec.
NCI deactivate procedure might take a long time,
depending on the local and remote parameters.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original driver contained some conditional code that was not selected,
but was not deleted in case it would be used later. That code can now be
removed.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables SRAM read function to support entire target memory.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On my testing, I saw some strange behavior
[ 421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[ 421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode
not sure how it happen, but adding the sanity check to prevent memory
corruption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce object size a few KB too.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
584493 55333 126800 766626 bb2a2 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pr_fmt() adds them. These are unnecessary and wrong.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does seem odd though to have a DBG_EMERG and not always
emit it.
What might also be useful for any embedded use is to add
CONFIG_RTLWIFI_DEBUG to conditionally remove all of the
debug logging code to reduce the largish object size.
This reduces the object size by about 1/3 (250KB)
when CONFIG_RTLWIFI_DEBUG is not set.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
368722 55333 94224 518279 7e887 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the KBUILD_MODNAME to the format reduces the
overall object size a small amount.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.new
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RT_TRACE macro already prepends it.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RT_ASSERT parentheses.
Align arguments.
Coalesce formats.
Remove unnecessary __func__ use as the macro uses it.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.new
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RTPRINT parentheses.
Coalesce formats.
Align arguments.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.new
594841 55333 129680 779854 be64e drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a single printk(KERN_DEBUG to emit the header line
to avoid any possible output interleaving.
Remove unnecessary parentheses from the calling uses.
Standardize header arg without trailing \n or colon.
Fix a few pairwiase/pairwise typos.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the macros a bit more readable.
Use do {...} while (0) without terminating semicolons.
Add missing terminating semicolon to a few uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All usage of ethtool_ops should be const; also add comma at end
of initializer list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped. This fixes the
problem.
Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4ce3c183fc (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.
percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmemcheck complains that ->redirect_genid doesn't get initialized.
Presumably it should be set to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
