Add remaining properties to the ethernet node and enable it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the pin control for the Ethernet MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethernet0 alias for ethernet so that u-boot can find this node
and fill in the MAC address.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Ethernet MAC node to mt8516.dtsi. This defines parameters common
to all the boards based on this SoC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PERICFG register range as a syscon. This will
soon be used by the MediaTek Ethernet MAC driver for NIC configuration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTC found on the MAX77620 PMIC can be used as a wakeup source on
Jetson Nano and TX1, which is useful to wake the system from suspend
at a given time.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
display controller and a new board using it, the Odroid Advance Go.
sdcard regulator for the rockpro64 and a lot of devicetree fixes
making the dt-binding check a lot happier.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl7F1N0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgV34CAChtYhGGRGEr8WwGL3WG1f8z1nwEfxEGaMx
niLnchgR2kWRiPFV8SVHaNkcGj9+VkeA/F8mCrrKiPDPrsL+s5X6q2liAmEGnIWo
OvlfyuIJNaSjnVxwhdZABIQsjjeLZI2i0OWGmq47vGopWaNWDGW9wrPlRslPrf4N
AIww1TwjKYK8Et5ja3COwfSt1gn2/PwR09wTfQwCy7wi9At6UWOQsDmpyFbjuTgv
GmPcQJZa2YtQovSM5FrbhguCKSGFSukopqqrrxmfsvlkz+xmZyeHN6MMpdNnwBXe
Kf3VU2p6b+75YouuOcJAAueBj6b37/tvi7KK/MZszdG2pM85SL1z
=BL2H
-----END PGP SIGNATURE-----
Merge tag 'v5.8-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New soc variant the rk3326 which is essentially a px30 with only one
display controller and a new board using it, the Odroid Advance Go.
sdcard regulator for the rockpro64 and a lot of devicetree fixes
making the dt-binding check a lot happier.
* tag 'v5.8-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: fix pinctrl-names for gpio-leds node on rk3326-odroid-go2
arm64: dts: rockchip: fix pd_tcpc0 and pd_tcpc1 node position on rk3399
arm64: dts: rockchip: add bus-width properties to mmc nodes for px30
arm64: dts: rockchip: remove disable-wp from rk3308-roc-cc emmc node
arm64: dts: rockchip: rename and label gpio-led subnodes
arm64: dts: rockchip: fix defines in pd_vio node for rk3399
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-orangepi
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-orangepi
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211f nodename for rk3328 Beelink A1
arm64: dts: rockchip: fix phy nodename for rk3328
include: dt-bindings: rockchip: remove unused defines
arm64: dts: rockchip: replace RK_FUNC defines in rk3326-odroid-go2
arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399
arm64: dts: rockchip: remove #sound-dai-cells from &spdif node of rk3399-hugsun-x99.dts
arm64: dts: rockchip: remove #sound-dai-cells from &i2s1 node of rk3399-pinebook-pro.dts
arm64: dts: rockchip: add Odroid Advance Go
dt-bindings: Add binding for Hardkernel Odroid Go Advance
arm64: dts: rockchip: add core devicetree for rk3326
...
Link: https://lore.kernel.org/r/1970481.V9vR1fIhX2@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various miscellaneous device tree source fixes to make them fully
binding compliant. It includes fixing various device node names,
order of interrupt properties, compatible names, address and size
cell fields and their aligment with children nodes as well as
moving some fixed devices out of bus node.
-----BEGIN PGP SIGNATURE-----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=Z5QL
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/Vexpress/Fast Models updates for v5.8
Various miscellaneous device tree source fixes to make them fully
binding compliant. It includes fixing various device node names,
order of interrupt properties, compatible names, address and size
cell fields and their aligment with children nodes as well as
moving some fixed devices out of bus node.
* tag 'juno-updates-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Fix SCPI shared mem node name
arm64: dts: vexpress: Fix VExpress LED names
arm64: dts: juno: Fix GPU interrupt order
arm64: dts: fvp/juno: Fix bus node names
arm64: dts: fvp: Fix SMMU DT node
arm64: dts: fvp/juno: Fix serial node names
arm64: dts: juno: Use proper DT node name for USB
arm64: dts: fvp: Fix ITS node names and #msi-cells
arm64: dts: fvp: Fix GIC child nodes
arm64: dts: juno: Fix GIC child nodes
arm64: dts: fvp: Fix GIC compatible names
arm64: dts: juno: Fix mem-timer
arm64: dts: juno: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed clocks out of bus node
arm64: dts: vexpress: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed devices out of bus node
arm64: dts: fvp/juno: Fix node address fields
Link: https://lore.kernel.org/r/20200519094702.GA32975@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For SDM845 this defines the IPA network accelerator and the CCI camera
control bus, it defines the required UFS reset and adds WiFi for the
Lenovo Yoga C630 and defines GPIO pin names and adds OV8856 and OC7251
camera nodes for DB845c.
For SC7180 it adds GPU support, defines the modem remoteproc, adds the
IPA network accelerator, Coresight and ETM support, adds cpuidle low
power states and updates the CPUs' compatible.
For SM8250 it adds regulators from the PM8150, PM8150L and PM8009 and
adds voltage corners, it defines the nodes for UFS PHY and controller
and finally corrects a typo in the PDC node to make SPMI functional.
For MSM8916 I2C1 and I2C5 are defined, a node for the CCI camera control
interface bus is added and Coresight is disabled by default to match
some product configurations. The Samsung A3U gained display support and
Samsung A5U gained touchscreen support.
MSM8996 now property describes the power supply chain for the GPU, the
CCI camera control interface bus is added and the DB820c has the
regulators of the secondary PMIC defined.
For QCS404 USB PHYs and controllers are defined and wired up for the
EVB.
SDM630/SDM660 platform support is added and the Xiaomi Redmi Note 7
defined.
It also contains a number of changes throughout to improve DT binding
compliance.
-----BEGIN PGP SIGNATURE-----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=ds6R
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.8
For SDM845 this defines the IPA network accelerator and the CCI camera
control bus, it defines the required UFS reset and adds WiFi for the
Lenovo Yoga C630 and defines GPIO pin names and adds OV8856 and OC7251
camera nodes for DB845c.
For SC7180 it adds GPU support, defines the modem remoteproc, adds the
IPA network accelerator, Coresight and ETM support, adds cpuidle low
power states and updates the CPUs' compatible.
For SM8250 it adds regulators from the PM8150, PM8150L and PM8009 and
adds voltage corners, it defines the nodes for UFS PHY and controller
and finally corrects a typo in the PDC node to make SPMI functional.
For MSM8916 I2C1 and I2C5 are defined, a node for the CCI camera control
interface bus is added and Coresight is disabled by default to match
some product configurations. The Samsung A3U gained display support and
Samsung A5U gained touchscreen support.
MSM8996 now property describes the power supply chain for the GPU, the
CCI camera control interface bus is added and the DB820c has the
regulators of the secondary PMIC defined.
For QCS404 USB PHYs and controllers are defined and wired up for the
EVB.
SDM630/SDM660 platform support is added and the Xiaomi Redmi Note 7
defined.
It also contains a number of changes throughout to improve DT binding
compliance.
* tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (68 commits)
arm64: dts: qcom: sc7180: Correct the pdc interrupt ranges
arm64: dts: qcom: sc7180: add IPA information
arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
arm64: dts: qcom: sc7180: Add A618 gpu dt blob
dt-bindings: arm-smmu: Add sc7180 compatible string
arm64: dts: qcom: msm8996: Make GPU node control GPU_GX GDSC
arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc
arm64: dts: qcom: apq8016-sbc: merge -pins.dtsi into main .dtsi
arm64: dts: qcom: msm8916: move gpu opp table to gpu node
arm64: dts: qcom: msm8916: avoid using _ in node names
arm64: dts: qcom: c630: Specify UFS device reset
arm64: dts: qcom: c630: Add WiFi node
arm64: dts: qcom: msm8916-samsung-a3u: add nodes for display panel
arm64: dts: qcom: db820c: Fix invalid pm8994 supplies
arm64: dts: qcom: db820c: Add pmi8994 RPM regulators
arm64: dts: qcom: msm8916: Disable coresight by default
arm64: dts: qcom: sc7180: Add "no-map" to cmd_db reserved area
arm64: dts: qcom: msm8916-samsung-a5u: Add touchscreen
arm64: dts: qcom: msm8916-samsung-a2015: Add touchscreen regulator
arm64: dts: qcom: msm8916: Add blsp_i2c5
...
Link: https://lore.kernel.org/r/20200519052528.1249950-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- replace deprecated compatible for the usb PHY
MT6797:
- switch to SPDX identifier
- add and enable I2C device for x20 development board
- add I2C compatible to the binding description
MT7622:
- add Wi-Fi device and enable it for the Bananpi-R64
MT8173:
- add CPU capacities based on Dhryston benchmark
- fix DT build warnings
- set throtteling range to limitless
- add Elm and Hana devices on which several chromebooks are based
- add Global Command Queue entries to the users
MT8183:
- split cpuidle states in two as the clusters have different target residencies
-----BEGIN PGP SIGNATURE-----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=tN8C
-----END PGP SIGNATURE-----
Merge tag 'v5.7-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
MT2712:
- replace deprecated compatible for the usb PHY
MT6797:
- switch to SPDX identifier
- add and enable I2C device for x20 development board
- add I2C compatible to the binding description
MT7622:
- add Wi-Fi device and enable it for the Bananpi-R64
MT8173:
- add CPU capacities based on Dhryston benchmark
- fix DT build warnings
- set throtteling range to limitless
- add Elm and Hana devices on which several chromebooks are based
- add Global Command Queue entries to the users
MT8183:
- split cpuidle states in two as the clusters have different target residencies
* tag 'v5.7-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8173: Add capacity-dmips-mhz attributes
arm64: dts: mt2712: use non-empty ranges for usb-phy
arm64: dts: mt8173: fix mdp aliases property name
arm64: dts: mediatek: Switch to SPDX license identifier for MT6797 SoC
arm64: dts: mediatek: Enable I2C support for 96Boards X20 Development board
arm64: dts: mediatek: Add I2C support for MT6797 SoC
dt-bindings: i2c: Document I2C controller binding for MT6797 SoC
arm64: dts: mt8173: fix cooling device range
arm64: dts: mediatek: add mt8173 elm and hana board
arm64: dts: mt8173: fix unit name warnings
arm64: dts: mt8173: add uart aliases
dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
arm64: dts: mt8183: adjust cpuidle target residency
arm64: dts: mt8173: Add gce setting in mmsys and display node
arm64: dts: mt7622: add built-in Wi-Fi device nodes
Link: https://lore.kernel.org/r/2794a8db-c14f-ac34-9e28-9f3700db6c4c@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
support, including:
- Support for the IOMMU on the H6
- Support for cpufreq / thermal throttling on the H6
- Support for the mailbox on the A64, A83t, H3, H5 and H6
- New boards: A20-OLinuXino-LIME-eMMC
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXr7NHgAKCRDj7w1vZxhR
xbhGAQCDavHkpjvq4Hwk/znoS0Y6NvW1JQUyKUWH8K6ah1ZkFwEA5gC0Ac9cbDAk
Q5fZeYl7mPbEL9DI0RphVqHmY2ezXw0=
=WR5/
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- Support for the IOMMU on the H6
- Support for cpufreq / thermal throttling on the H6
- Support for the mailbox on the A64, A83t, H3, H5 and H6
- New boards: A20-OLinuXino-LIME-eMMC
* tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (23 commits)
arm64: dts: allwinner: h6: Add IOMMU
arm64: dts: allwinner: h6: Enable CPU opp tables for Tanix TX6
arm64: dts: allwinner: h6: add voltage range to OPP table
arm64: dts: allwinner: sun50i-a64: Add missing address/size-cells
arm64: dts: allwinner: h6: Enable CPU opp tables for Pine H64
arm64: dts: allwinner: Sort Pine H64 device-tree nodes
arm64: dts: allwinner: h6: Enable CPU opp tables for Orange Pi 3
arm64: dts: allwinner: h6: Enable CPU opp tables for Beelink GS1
arm64: dts: allwinner: h6: Add CPU Operating Performance Points table
arm64: dts: allwinner: h6: Add thermal trip points/cooling map
arm64: dts: allwinner: h6: Add clock to CPU cores
arm64: allwinner: h6: orangepi-lite2: Support BT+WIFI combo module
arm64: dts: allwinner: h6: orangepi: Disable OTG mode
arm64: dts: allwinner: h6: orangepi: Add gpio power supply
ARM: dts: sun8i-h2-plus-bananapi-m2-zero: Fix led polarity
arm64: dts: allwinner: h6: Add msgbox node
arm64: dts: allwinner: a64: Add msgbox node
ARM: dts: sunxi: h3/h5: Add msgbox node
ARM: dts: sunxi: a83t: Add msgbox node
ARM: dts: sun8i-h3: add opp table for mali gpu
...
Link: https://lore.kernel.org/r/cfa66bd9-f74c-4614-9ea5-9ef8546cc571.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5g8QAKCRCKwlD9ZEnx
cDusAQD4SCmyY0MZZNWQhkhu2ics2wYpKItw4Y7E4fl9XUlXkQEAyyN11vVNoteX
7KvNX7/9eXpberlcx4H6szPQsOzWzwM=
=2KDk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8 (take two)
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
ARM: dts: r8a7742: Add GPIO nodes
ARM: dts: r8a7742: Add [H]SCIF{A|B} support
ARM: dts: r8a7742: Add IRQC support
ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
ARM: dts: r8a7742: Initial SoC device tree
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add pinconf for spi2 and spi3 nodes and increase the drive
strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJevjyIAAoJEAvIV27ZiWZcGoYQAJdLtw+VmW+NarmObzZ1vFh9
tpAWA1UDgH6oY61lscdbi8feAYmj2i8kdCCEFldxUSQCcVFX3MoZAJMTb18EaASg
tJpLvHcNd47BYv+t9VdlIcEsbKHmZO1eJU4KnzOR4uHr6sS1n4spwpPV7lhIFoHY
yp5xZSp5COraHrmBkytgcLgxMhLmQl40Kej1MF2Ce6bP/+C10UuejPOn8KaO9bmm
+7ipF0B254HxmzJJlNWszVJiBweX8UYmeSAe/xLz5mbKAHYnZ1R9Iz2+lJO8SQSz
ztPrZ5JRW+FNGbHq+Q+e5l2OdxcVoIptlHLbrrmVCt7NoTm/CeXnOg7SzxfHN8J9
Y8GyFugjXRV4Oe/3SzlApy4Yq5Hf3iAi0jNrbwQHasKptOXEIP/XLP+slppbQmPY
aklo8iIxM9rUuqHoolFmvl+KE8B7v12YkhBa0sQXWwbGNW2jF6cBknHRC/Lrq6/a
W0VDdAQJ+Tu8fLvG2mO71ZGAvSC0FMkkQ1XE6wMKNkbwf4g1DCgkK+EqQV1eeZcz
WJfgwyMQcql6uv5ICbvgiL48MrAxDCaxMLvvjZc1ti9e2DDMROXILCR5Z/tKd8UB
+2ve/5xcVdujClfpPUoAPwKGrRG9cKZ4PuNOfw5YGntFvLBwhXjtLCjf3/hF4dbD
Qt9KY+9bBMDcf3qY4JrX
=+heh
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.8
- Add pinconf for spi2 and spi3 nodes and increase the drive
strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board
* tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: Add CTI options
arm64: dts: hikey960: pinctrl: Fix spi2/spi3 pinconf
Link: https://lore.kernel.org/r/5EBE430E.6090508@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'pinctrl-names' property should contain a list of names
to the assigned states. The value 'led_pins' in the gpio-leds
node on rk3326-odroid-go2 is not a state that is normally used,
so change it the common name 'default'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200519111444.2208-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400
reference board with an S922X chip.
- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200520014329.12469-6-christianshewitt@gmail.com
Convert the Ugoos AM6 dts into meson-g12b-w400.dtsi, and then create
a new AM6 dts that references it. This is in preparation for several
new G12B devices that will share the common w400 dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200520014329.12469-2-christianshewitt@gmail.com
Keep the switch port labels consistent across the different board
variants. If the user wants to rename them, it should be done in
user-space.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RTC found on the MAX77620 PMIC can be used as a wakeup source on
Jetson TX2, which is useful to wake the system from suspend at a given
time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Enable the VI I2C so that the peripherals connected to it (such as the
camera connector, an INA3221 power monitor and the USB 3.1 4-port hub)
can be accessed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 contains VI controller for video input capture from MIPI
CSI camera sensors and also supports built-in test pattern generator.
CSI ports can be one-to-one mapped to VI channels for capturing from
an external sensor or from built-in test pattern generator.
This patch adds support for VI and CSI and enables them in Tegra210
device tree.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 device tree is missing reset-cells property for the memory
controller node. This patch adds it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 device tree lists CSI clock and reset under SOR powergate
node.
But Tegra210 has CSICIL in SOR partition and CSI in VENC partition.
So, this patch includes fix for SOR powergate node.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMIC RTC is currently unable to wakeup Tegra194 on the Jetson Xavier
platform because the interrupt from the PMIC is not usin the PMC as the
interrupt parent but the GIC directly. Update the PMIC interrupt to use
the PMC as the interrupt parent so that the PMIC RTC alarms can wakeup
the device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 'phy-mode' property is currently defined as 'rgmii' for Jetson
Xavier. This indicates that the RGMII RX and TX delays are set by the
MAC and the internal delays set by the PHY are not used.
If the Marvell PHY driver is enabled, such that it is used and not the
generic PHY, ethernet failures are seen (DHCP is failing to obtain an
IP address) and this is caused because the Marvell PHY driver is
disabling the internal RX and TX delays. For Jetson Xavier the internal
PHY RX and TX delay should be used and so fix this by setting the
'phy-mode' to 'rgmii-id' and not 'rgmii'.
Fixes: f89b58ce71 ("arm64: tegra: Add ethernet controller on Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The external memory controller can be used as a cooling device for the
LPDDR chips. Hook it up to the "mem" thermal zone of the SOCTHERM block
so that temperature polling can be enabled on the EMC when a given
temperature is exceeded.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Node names are supposed to match the class of the device. The
mmsys node is a syscon as it provides more then just a clock controller.
Update the name.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20200518113156.25009-4-matthias.bgg@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Node names are supposed to match the class of the device, mmsys is a
system controller (syscon) not a clock controller, so change the node
name accordingly.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20200401201736.2980433-4-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Interrupts is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupts is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign IMX8M*_CLK_A53_SRC's parent to system pll1 and
assign IMX8M*_CLK_A53_CORE's parent to arm pll out as what
is done in drivers/clk/imx/clk-imx8m*.c, then we could remove
the settings in driver which triggers lockdep warning.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the LPUART has support for the LS1028A SoC, also enable it on
our board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Ethernet interrupt details to the WeTek Hub/Play2 dtsi to resolve
an issue with Ethernet probing in mainline u-boot.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200518025451.16401-1-christianshewitt@gmail.com
The Smartlabs SML-5442TW is based on the Amlogic P231 reference design
but with the following differences:
- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- QCA9377 instead of the usual Ampak/Broadcom module
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200510124129.31575-4-christianshewitt@gmail.com
add the internal DAC glue support on the g12 and sm1 family
This glue connects the different TDM interfaces of the SoC to
the internal audio DAC codec.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-8-jbrunet@baylibre.com
Add the internal DAC support on the libretech CC. The output of this
DAC is provided on the 9J4 connector.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-6-jbrunet@baylibre.com
Add the internal DAC support on the libretech CC. The output of this
DAC is provided on the 9J5 connector.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-5-jbrunet@baylibre.com
Add the internal DAC support on the libretech CC. The output of this
DAC is provided on the 3.5mm jack connector.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-4-jbrunet@baylibre.com
Add the necessary bits to support the internal audio DAC the p230/q200
reference design derivated boards. The output of this DAC is provided
on the 3.5mm jack connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-3-jbrunet@baylibre.com
Add the board support for the Hardkernel Odroid-C4 single board computer.
The Odroid-C4 is the Odroid-C2 successor with same form factor, but using
a modern Amlogic S905X3 (SM1) SoC and 4x USB3 ports.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506080702.6645-3-narmstrong@baylibre.com
Add basic audio support on the p230/q200 reference design.
This initial support is limited to HDMI i2s and SPDIF (LPCM).
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20200421163935.775935-4-jbrunet@baylibre.com
Add the AIU audio device to the Amlogic GX SoC family DT.
ATM, this device provides the i2s and spdif output stages and also
the hdmi and internal codec glues.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20200421163935.775935-3-jbrunet@baylibre.com
The pd_tcpc0 and pd_tcpc1 nodes are currently a sub node of pd_vio.
In the rk3399 TRM figure of the 'Power Domain Partition' and in the
table of 'Power Domain and Voltage Domain Summary' these power domains
are positioned directly under VD_LOGIC, so fix that in 'rk3399.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Link: https://lore.kernel.org/r/20200428203003.3318-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
'bus-width' and pinctrl containing the bus-pins
should be in the same file, so add them to
all mmc nodes in 'px30.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200416183053.6045-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The mmc-controller.yaml didn't explicitly say disable-wp is
for SD card slot only, but that is what it was designed for
in the first place.
Remove all disable-wp from emmc or sdio controllers.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20191219121954.2450-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm64/boot/dts/rockchip/rk3368-r88.dt.yaml: gpio-leds:
'work' does not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: pd_vio@15:
'pd_tcpc0@RK3399_PD_TCPC0', 'pd_tcpc1@RK3399_PD_TCPC1'
do not match any of the regexes:
'.*-names$', '.*-supply$', '^#.*-cells$',
'^#[a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$',
'^__.*__$', 'pinctrl-[0-9]+'
Fix error by replacing the wrong defines by the ones
mentioned in 'rk3399-power.h'.
make -k ARCH=arm64 dtbs_check
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428203003.3318-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy@1:
'#phy-cells' is a required property
The phy nodename is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy@1:
'#phy-cells' is a required property
The rtl8211e node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: phy@0:
'#phy-cells' is a required property
The rtl8211f node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The defines RK_FUNC_1 and RK_FUNC_2 are deprecated,
so replace them with the preferred form.
Restyle properties in the same line.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200512203524.7317-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The lack of unique context in '0f1decaa83b7 ("arm64: dts: qcom: sc7180:
Support ETMv4 power management")' caused the patch to be applied
off-by-one. Move the "arm,coresight-loses-context-with-cpu" properties
down one node, so that it applies to the ETMs and not the replicator.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SRAM DT binding requires child nodes to use a certain node name
scheme.
Change the naming from scp-shmem to scp-sram to comply with that.
Link: https://lore.kernel.org/r/20200513103016.130417-19-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Mali binding insists on the GPU interrupts to be in ordered as: job,
mmu, gpu.
Sort the GPU interrupts and interrupt-names properties accordingly.
Link: https://lore.kernel.org/r/20200513103016.130417-17-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Most Arm Ltd. boards are employing a layered bus structure, to map
the hardware design (SoC, motherboard, IOFPGA) and structure the DTs.
The "simple-bus" nodes only allow a limited set of node names. Switch
to use *-bus to be binding compliant.
This relies on a pending dt-schema.git fix for now:
https://github.com/devicetree-org/dt-schema/pull/38
Link: https://lore.kernel.org/r/20200513103016.130417-16-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SMMU name in the RevC FVP DT file was not fully binding compliant.
Adjust the node name to match the binding's list of allowed names, also
shuffle the order of the interrupts to comply with the expected order.
Link: https://lore.kernel.org/r/20200513103016.130417-15-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The UARTs for all Arm Ltd. boards were using "uart" as their node name
stub.
Replace that with the required "serial" string, to comply with the PL011
DT binding.
Link: https://lore.kernel.org/r/20200513103016.130417-14-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The EHCI/OCHI DT binding requires to use "usb" as the node name stub.
Replace the existing name with "usb" to comply with the binding.
Link: https://lore.kernel.org/r/20200513103016.130417-13-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The GIC ITS nodes in the fastmodel DTS files were not fully binding
compliant.
Use one of the allowed node names, also add the required #msi-cells
property for the older model.
Link: https://lore.kernel.org/r/20200513103016.130417-12-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The GIC DT nodes for the fastmodels were not fully compliant with the
DT binding, which has certain expectations about child nodes and their
size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Since the .dts files share interrupt nexus nodes across different
interrupt controllers (GICv2 vs. GICv3), we need to use the only
commonly allowed #address-size value of <1> for both.
Link: https://lore.kernel.org/r/20200513103016.130417-11-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The GIC DT nodes for the Juno boards were not fully compliant with
the DT binding, which has certain expectations about child nodes and
their size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Link: https://lore.kernel.org/r/20200513103016.130417-10-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The GIC DT binding only allows certain combinations of DT compatible
strings. The somewhat awkward "arm,cortex-a15-gic", "arm,cortex-a9-gic"
is not among those.
Drop that combination of different "cortex" based strings used for the
models, and replace it with the more useful combination including
"arm,gic-400".
Link: https://lore.kernel.org/r/20200513103016.130417-9-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Juno's mem-timer DT node was not fully compliant with the DT binding,
which has certain expectation about child nodes and their size and
address cells values.
Use a cell size of 1, as the binding requests, and spell out the ranges
property to be binding compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-8-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the gpio keys to the
root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-7-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks to the root node, since they do not depend on any
busses.
Link: https://lore.kernel.org/r/20200513103016.130417-6-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The sfp compatible should be 'sff,sfp', not 'sff,sfp+'. We used patched
kernel where the latter was working.
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the config bus subtree
to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use sdhci-caps-mask to forbid SDR104 mode on the SDIO capable SDHCI
controller. Without this the device cannot pass electromagnetic
interference certifications.
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Move the max-link-speed property of the PCIe node from board specific
device tree files to the generic armada-37xx.dtsi.
Armada 37xx supports only PCIe gen2 speed so max-link-speed property
should be in the generic armada-37xx.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.
This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
