Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.
The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.
If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.
Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.
Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().
Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added a flag to indicate that core is in hibernation,
it is used to determine the hibernation state of the core.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We better print an error in case probing of dwc2 fails on
setting the DMA coherent mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* Remove braces for one-line statements
* Add missing braces where another arm in if-statement uses braces
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replace this by statically defining a function with defaults, and just
assigning it. This will allow us to use parameters of any type and any
default value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Consolidate and move all the parameter initialization code from the
probe function to params.c.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a params.c file and move all driver parameter code there, including
all the static parameter definitions.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAV/gzeGCrR//JCVInAQKVhw/5AS5R2S7m7VTlWMvGjvH9ITudYhiAGJP1
z5nP5SwJsfmSjfvw0kSxGUmsNS3rHutsPMz65EesKqFuC3LPZiqMUqrzxt9iqqJx
I+XdAxDTnOE1RBZFtB9dL+qLzHQ87pMo6R9dfs32sxb3QuCQBYhcFyLmQDuZuHH0
yeDi3ARFvgxx/qoRUA7cnSlY5RLNzM44y+Ik/ZcVr4ReqYBC2g5mGi5htoiNSLWR
nwWR+5hNLAp44OZgkZfNsf6kB9brWDQh3PbnBjy6sKXSBoSVIfxTweh2DMJXbZ7l
1Ck+S7WyLMhGJp448TcuBykr/l9i3uqNh061XavjwP8CAjAdZ787XlnNSztc2pyh
dvbI/E76pLGb5ZoFdqlY2Syl63ZFN4K8mjZMSPYfYKf85EDIxe4MYwpbo7/pwzh3
8OlBwH6r4aUMw+QgE1nx8nsjaCoGDMFdgJeJJaWdriZ6Nst2n5gREk/mzbrAWkNG
ujChn/6hES9LuE21aCp1ipB7qnnyeRinfqz2acEFxMQxuPdjwKrdJqNsBaTWsapE
Z+b/BFP+LTdPfHCmMSVwfMrNbwsoY7+L4EXXL36lUgOwcDp0vCXA+PiiahYASewA
1LDQ3CURCEapdBhVU+06Kb4y5eWU7M7EqpOwpHgRJ92dVxgNxuCfcurvxzqPP1UP
3O4R7bfUTTg=
=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Allow for platforms that have a reset controller driver in place to bring
the USB IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleanup in probe if we fail to get dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As documented in dwc2_calculate_dynamic_fifo(), host_rx_fifo_size should
really be:
2 * ((Largest Packet size / 4) + 1 + 1) + n
with n = number of host channel.
We have 9 host channels, so
2 * ((1024/4) + 2) + 9 = 516 + 9 = 525
We've got 960 / 972 total_fifo_size on rk3288 (and presumably on
rk3066) and 525 + 128 + 256 = 909 so we're still under on both ports
even when we increment by 5.
In the future, it would be nice if dwc2_calculate_dynamic_fifo() could
handle the "too small" FIFO case and come up with something more
dynamically. When we do that we can figure out how to allocate the
extra 48 / 60 bytes of FIFO that we're currently wasting.
NOTE: no known bugs are fixed by this patch, but it seems like a simple
fix and ought to fix someone.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously we needed to set the max_transfer_size to explicitly be 65535
because the old driver would detect that our hardware could support much
bigger transfers and then would try to do them. This wouldn't work
since the DMA alignment code couldn't support it.
Later in commit e8f8c14d9d ("usb: dwc2: clip max_transfer_size to
65535") upstream added support for clipping this automatically. Since
that commit it has been OK to just use "-1" (default), but nobody
bothered to change it.
Let's change it to default now for two reasons:
- It's nice to use autodetected params.
- If we can remove the 65535 limit, we can transfer more!
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 263b7fb557 ("usb: dwc2: Move reset into
dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB
ethernet fails, due to being unable to pick up proper parameters when
performing a plain reset before reading hw params.
Below shows the results of the gnptxfsiz and hptxfsiz with and before
and after reverting this (from Stefan Wahren):
So here is the probe result before Patch 1 is applied:
[ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000
[ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000
[ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 1.394249] dwc2 20980000.usb: DWC OTG Controller
[ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000
And here is the probe result after Patch 1 is applied:
[ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000
[ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000
[ 1.434301] dwc2 20980000.usb: DWC OTG Controller
[ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset already happens before this so just force the dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The reset is required to get reset values of the hardware parameters but
the force mode is not. Move the base reset into dwc2_get_hwparams() and
do the reset and force mode afterwards.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dr_mode parameter was being checked against how the dwc2 module
was being configured at compile time. But it wasn't checked against
the hardware capabilities, nor were the hardware capabilities checked
against the compilation parameters.
This commit adds those checks and adjusts dr_mode to an appropriate
value, if needed. If the hardware capabilities and module compilation
do not match then we fail as it wouldn't be possible to run properly.
The hardware, module, and dr_mode, can each be set to host, device,
or otg. Check that all these values are compatible and adjust the
value of dr_mode if possible.
The following table summarizes the behavior:
actual
HW MOD dr_mode dr_mode
------------------------------
HST HST any : HST
HST DEV any : ---
HST OTG any : HST
DEV HST any : ---
DEV DEV any : DEV
DEV OTG any : DEV
OTG HST any : HST
OTG DEV any : DEV
OTG OTG any : dr_mode
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.
Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch make sure that all necessary members of dwc2_hsotg
are initialized before the irq handler is requested. So
the kernel oops triggered by dwc2_handle_common_intr has
been fixed.
dwc2 20980000.usb: Configuration mismatch. Forcing host mode
dwc2 20980000.usb: no platform data or transceiver defined
Unable to handle kernel paging request at virtual address cc860040
pgd = c0004000
[cc860040] *pgd=0b41e811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc3+ #19
Hardware name: BCM2835
task: cb494000 ti: cb4d0000 task.ti: cb4d0000
PC is at dwc2_is_controller_alive+0x18/0x34
LR is at dwc2_handle_common_intr+0x24/0xb60
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change made the otg clk a requirement and broke some
platforms when it was moved into platform.c.
So make clk handling optional again.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
When searching for PHYs, any error was treated as if the PHY did not
exist or was not specified. Thus the probe function did not
correctly return error conditions such as -EPROBE_DEFER.
Fixed so that only a non-existing PHY is ignored and any other error
is returned.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change introduced a check from the gadget requiring
that a PHY is specified. This requirement never existed on the host
side and broke some platforms when it was moved into platform.c.
The gadget doesn't require the PHY either so remove the check.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Stefan Wahren <info@lategoodbye.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8c4 ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Even when DWC2 is in (internal) suspended state, it should disable PHY
in suspend and then enable it in resume. This patch fixes unbalanced PHY
control sequence.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dual role configuration is not selected, check and force dr_mode
based on the selected configuration.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2 may not be able to exit from hibernation if the hardware
does not provide a way to detect resume signalling in this state.
Thus, add the possibility to disable hibernation feature.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.
Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prepare to add more debug code. Moreover, don't save dentry * for
each file in struct dwc2_hsotg as clean up is done with
debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed
altogether for the same reason.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
