- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5g8QAKCRCKwlD9ZEnx
cDusAQD4SCmyY0MZZNWQhkhu2ics2wYpKItw4Y7E4fl9XUlXkQEAyyN11vVNoteX
7KvNX7/9eXpberlcx4H6szPQsOzWzwM=
=2KDk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8 (take two)
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
ARM: dts: r8a7742: Add GPIO nodes
ARM: dts: r8a7742: Add [H]SCIF{A|B} support
ARM: dts: r8a7742: Add IRQC support
ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
ARM: dts: r8a7742: Initial SoC device tree
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-fix a typo for DAC io-channel-cells on f429 and h743
MPU part:
-Generic:
-Bump tp PSCI 1.0
-Fix a typo for DAC io-channel-cells
-Add M4 pdds for deep sleep mode
-Add I2C fatmode plus support
-Add new Octavio lxa-mc1 board based on OSDMP15x SiP
-Add new Stinger96 board support. It is a 96Boards IoT Extended board
based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
Onboard BG96 modem...
-Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
VOC sensor, 2 digitals microphones ...
-DH:
-Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
-Add GPIO led and GPIO keys support on PDK2 board
-AV96:
-Major rework to support official avenger96 board based on DHCOR SOM.
-Prototype board is no more supported
-----BEGIN PGP SIGNATURE-----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=JFtr
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.8, round 1
Highlights:
----------
MCU part:
-fix a typo for DAC io-channel-cells on f429 and h743
MPU part:
-Generic:
-Bump tp PSCI 1.0
-Fix a typo for DAC io-channel-cells
-Add M4 pdds for deep sleep mode
-Add I2C fatmode plus support
-Add new Octavio lxa-mc1 board based on OSDMP15x SiP
-Add new Stinger96 board support. It is a 96Boards IoT Extended board
based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
Onboard BG96 modem...
-Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
VOC sensor, 2 digitals microphones ...
-DH:
-Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
-Add GPIO led and GPIO keys support on PDK2 board
-AV96:
-Major rework to support official avenger96 board based on DHCOR SOM.
-Prototype board is no more supported
* tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (58 commits)
ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add IoT Box board support
dt-bindings: arm: stm32: Document IoT Box compatible
ARM: dts: stm32: Add Stinger96 board support
dt-bindings: arm: stm32: Document Stinger96 compatible
ARM: dts: stm32: Add missing pinctrl entries for STM32MP15
dt-bindings: Add vendor prefix for Shiratech Solutions
ARM: dts: stm32: Add bindings for SPI2 on AV96
ARM: dts: stm32: Add alternate pinmux for SPI2 pins
ARM: dts: stm32: Add bindings for ADC on AV96
ARM: dts: stm32: Add alternate pinmux for ADC pins
ARM: dts: stm32: Add bindings for FDCAN2 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN2 pins
ARM: dts: stm32: Add bindings for FDCAN1 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN1 pins
ARM: dts: stm32: Repair I2C2 operation on AV96
ARM: dts: stm32: Add alternate pinmux for I2C2 pins
...
Link: https://lore.kernel.org/r/19160355-364d-170c-7ae2-5ba7f714103f@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
-----BEGIN PGP SIGNATURE-----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=kTHc
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.8
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
* tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: s5pv210: Set MAX8998 GPIO pulls on Aries boards
ARM: dts: s5pv210: Correct FIMC definitions
ARM: dts: s5pv210: Assign clocks to MMC devices on Aries boards
ARM: dts: s5pv210: Enable ADC on Aries boards
ARM: dts: s5pv210: Add an ADC node
ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards
ARM: dts: s5pv210: Add si470x FM radio to Galaxy S
ARM: dts: s5pv210: Add remaining i2c-gpio adapters to Aries boards
ARM: dts: s5pv210: Add panel support to Aries boards
ARM: dts: s5pv210: Add touchkey support to Aries boards
ARM: dts: s5pv210: Add FSA9480 support to Aries boards
ARM: dts: s5pv210: Add WM8994 support to Aries boards
ARM: dts: s5pv210: Disable pulls on GPIO I2C adapters for Aries
ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries
ARM: dts: s5pv210: Correct gpi pinctrl node name
ARM: dts: s5pv210: Add sleep GPIO configuration for Galaxy S
ARM: dts: s5pv210: Add sleep GPIO configuration for Fascinate4G
ARM: dts: s5pv210: Add helper define for sleep gpio config
ARM: dts: exynos: Enable WLAN support for the UniversalC210 board
ARM: dts: exynos: Enable WLAN support for the Rinato board
...
Link: https://lore.kernel.org/r/20200512122922.5700-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
-----BEGIN PGP SIGNATURE-----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=cX7l
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use firmware PM driver for V3D
ARM: dts: bcm2711: Add vmmc regulator in emmc2
ARM: dts: bcm2711: Update expgpio's GPIO labels
Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
-----BEGIN PGP SIGNATURE-----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=WgDN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
DTS changes for omaps for v5.8 merge window
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP5: Make L4SEC clock domain SWSUP only
ARM: OMAP4: Make L4SEC clock domain SWSUP only
ARM: dts: omap5: add DES crypto accelerator node
ARM: dts: omap5: add SHA crypto accelerator node
ARM: dts: omap5: add aes2 entry
ARM: dts: omap5: add aes1 entry
ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
ARM: dts: DRA72x: Add aliases for rproc nodes
ARM: dts: DRA74x: Add aliases for rproc nodes
...
Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl6oi4YACgkQQRCzN7AZ
XXOpVBAAxco/qwxQndEPMWDVCtqOdhXglUvq220V5PQ4DNvpm52QeG65rwwR2TK9
Nun/vW70JZnXysGS4ZAU9NKToenyIdacwfFCea1eDK7cWpbZzZGo3dkMsr90KBah
iGDx1ua/lAPxP+IhGlv8GBFQ4rMYzBewaAvk30pi3FtoV/gUjszqLUX1UI7TTaEA
LWlI4t9aFrRryTsffVzCMXKWUbovMfPtf7dvi+H+Paid8x5PVRwpo91eLknydwb6
BQAxFhaNy34U27DIsH4L2ulcy7xFBwlmOVHA8h9cTq5qFF/ASxAhAmdQvg+DzjqK
8YZkWAgOMfwuY+zDFHsvGMJXWZeNOfo76tV0QhiHPlC9JcvOxc95SH7SDwTVjQ/v
JyLfqMxz6VaL4tL5j2APHgjQzpNtOs6aPNiUkmxrz3iLGuzi51f+Ua/I5MbYd2ME
oyW21YIebHtiHhZ30NenS0hnD2prFzsdDZLgI04LKwCTW56xM2XS7diz1if+yxJ8
49LWboInAq8B4ipuRmzNrUoWZlcYZcdUh/7gi1xCwkdpg0rNj/3hKzeRf3W78yw2
Tve2E2TK+I+l4bJclCjdYzbkWUkheZWApx5nK+4kAAwS+rr1AM4oXZYtd7530LUK
YL9CavQeDL8SfW8zzCVooureO9MDdzYb5o+joKhaBejgvCGThOg=
=XZ07
-----END PGP SIGNATURE-----
Merge tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.8 kernel:
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Add devicetree for Integrator/AP with IM-PD1
Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an Avenger96 reference board. The DHCOR SoM can be populated with any
STM32MP15xx. Split the DTs to reflect this such that the common SoM and
Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example
implementation of STM32MP157A SoM and Avenger96 board is separated into
stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for
the sake of backward naming compatibility.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx
variant. Split the SoC-independent parts of the SoM and PDK2 into the
stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example
of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5
GPIO-E may conflict with touchscreen interrupt, hence LED5 must be
disabled when using the DH 560-200 display unit with touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add bindings for the four GPIO keys on DH PDK2 board. Note that TA1
key is polled because it's IRQ line conflicts with ethernet IRQ, the
rest of the GPIO keys, TA2, TA3, TA4, are interrupt-driven and wake
up sources.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
IoT Box is an IoT gateway device based on Stinger96 board powered by
STM32MP1 SoC, designed and manufactured by Shiratech Solutions. This
device makes use of Stinger96 board by having it as a base board with
one additional mezzanine on top.
Following are the features exposed by this device in addition to the
Stinger96 board:
* WiFi/BT
* CCS811 VOC sensor
* 2x Digital microphones IM69D130
* 12x WS2812B LEDs
Following peripherals are tested and known to work:
* WiFi/BT
* CCS811
More information about this device can be found in Shiratech website:
https://www.shiratech-solutions.com/products/iot-box/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Stinger96 is a 96Boards IoT Extended edition board designed and
manufactured by Shiratech solutions based on STM32MP1 SoC. Following
are the features of this board:
* 256MB DDR
* 125MB NAND Flash
* Onboard BG96 modem
* 1x uSD
* 2x USB (1 available as external connector and another connected to BG96)
* 1x SPI
* 1x PCM
* 2x UART (apart from serial console)
* 2x I2C (apart from one connected to PMIC)
Following peripherals are tested and known to work:
* BG96 modem
* 1x I2C (LS-I2C0)
* 1x SPI
* 1x UART (LS-UART0)
* USB (Only Gadget mode)
* uSD
More information about this board can be found in Shiratech website:
https://www.shiratech-solutions.com/products/stinger96/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These pinctrl definitions will be used by Stinger96/IoTBox boards
from Shiratech.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add SPI2 bindings to AV96 DT, the SPI2 IOs are present on
low-speed expansion connector X6. This is disabled by default
and can be enabled if something is connected there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for SPI2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for ADC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add FDCAN2 bindings to AV96 DT, the FDCAN2 is present on low-speed
expansion connector X6. This is disabled by default to match the
96boards specification though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add FDCAN1 bindings to AV96 DT, the FDCAN1 is present on low-speed
expansion connector X6. This is disabled by default to match the
96boards specification though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN1 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The I2C2 uses different pinmux on AV96, use correct pinmux and
also add comments about the I2C being present on the "low-speed"
expansion connector X6.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Declare PSCI v1.0 support instead of v0.1 as the former is supported
by the PSCI firmware stacks stm32mp15x relies on.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Commit c2ce5fb3f3 ('ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP
only') made DRA7 SoC L4SEC clock domain SWSUP only because of power
state transition issues detected with HWSUP mode. Based on
experimentation similar issue exists on OMAP5, so do the same change
for OMAP5 also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit c2ce5fb3f3 ('ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP
only') made DRA7 SoC L4SEC clock domain SWSUP only because of power
state transition issues detected with HWSUP mode. Based on
experimentation similar issue exists on OMAP4, so do the same change
for OMAP4 also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 contains a single DES crypto accelerator instance. Add node for
this in DT to enable it.
We keep the node disabled for now, as it appears OMAP5 platform is
running out of available DMA channels, and DES is the least interesting
crypto accelerator available on the device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the single available SHA crypto accelerator device for OMAP5 SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES2 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES1 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timer information has been added to all the IPU and DSP
remote processor device nodes in the DRA7xx/AM57xx SoC families. The
data has been added to the two common dra7-ipu-dsp-common and
dra74-ipu-dsp-common dtsi files that can be included by all the
desired board files. The following timers are chosen as the watchdog
timers, as per the usage on the current firmware images:
IPU2: GPTimers 4 & 9 (one for each Cortex-M4 core)
IPU1: GPTimers 7 & 8 (one for each Cortex-M4 core)
DSP1: GPTimer 10
DSP2: GPTimer 13
Each of the IPUs has two Cortex-M4 processors and so uses a timer
each for providing watchdog support on that processor irrespective of
whether the IPU is running in SMP-mode or non-SMP node. The chosen
timers also need to be unique from the ones used by other processors
(regular timers or watchdog timers) so that they can be supported
simultaneously.
The MPU-side drivers will use this data to initialize the watchdog
timer(s), and listen for any watchdog triggers. The BIOS-side code on
these processors needs to configure/refresh the corresponding timer
properly to not throw a watchdog error.
The watchdog timers are optional in general, but are mandatory to
be added to support watchdog error recovery on a particular processor.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and
the DSP remoteproc devices on the DRA76 EVM board, and assigned to
the respective rproc device nodes. These match the configuration
used on the DRA7 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA76 EVM board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA71 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and
the DSP1 remoteproc devices on the DRA72 EVM rev C board, and assigned
to the respective rproc device nodes. These match the configuration
used on the DRA72 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA72 EVM rev C board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA72 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on DRA7 EVM board. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for all the IPU and
DSP remoteproc devices in the DRA7 SoC family. The data is added
to the two common dra7-ipu-dsp-common and dra74-ipu-dsp-common
dtsi files that are included by all the desired board files. The
following timers are chosen, as per the timers used on the current
firmware images:
IPU2: GPTimer 3
IPU1: GPTimer 11
DSP1: GPTimer 5
DSP2: GPTimer 6
The timers are optional, but are mandatory to support advanced device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, if needed.
Each of the IPUs has two Cortex-M4 processors, and is currently
expected to be running in SMP-mode, so only a single timer suffices
to provide the BIOS tick timer. An additional timer should be added
for the second processor in IPU if it were to be run in non-SMP mode.
The timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required 'mboxes' property to all the IPU and DSP remote
processors (IPU1, IPU2, DSP1 and DSP2) in the two available common
dtsi files - dra7-ipu-dsp-common and dra74-ipu-dsp-common dtsi files.
The latter file is for platforms having DRA74x/DRA76x/AM572x/AM574x
SoCs which do have a DSP2 processor in addition to the other common
remote processors. The common data is added to the former file, and
the DSP2 only data is added to the latter file.
The mailboxes are required for running the Remote Processor Messaging
(RPMsg) stack between the host processor and each of the remote
processors. Each of the remote processors uses a single sub-mailbox
node, the IPUs are assumed to be running in SMP-mode. The chosen
sub-mailboxes match the values used in the current firmware images.
This can be changed, if needed, as per the system integration needs
after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for all the 3 remote processor nodes common to
all DRA72x/DRA71x/AM571x/AM570x boards. The aliases uses the
stem "rproc", and are defined in the order of the most common
processors on the DRA72x family. The ids are same as DRA74x
except for the missing DSP2.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
