This fixes a problem found on the MacBookPro 2017 Retina panel.
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec = multiplier 0xc),
but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to add the additiional 324000 kbps link rate during
edp setup.
Link to previous discussion of a different attempted fix
with Ville and Jani:
https://patchwork.kernel.org/patch/11325935/
v2: Follow Jani's proposal of defining quirk_rates[] instead
of just appending 324000. This for better clarity.
v3: Rebased onto current drm-tip, as of 16-March-2020. Adapt
to new edid_quirks parameter of drm_dp_has_quirk().
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316042340.4783-1-mario.kleiner.de@gmail.com
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hdcp.c.
This also involves extracting the drm_i915_private device from the
intel_connector type for use in the macros.
v2 by Jani:
- rebase
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47d5e88dedc08ee48938344296ada550dedd5f90.1583766715.git.jani.nikula@intel.com
Convert various instances of printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_fbdev.c.
This also involves extracting the drm_i915_private device from various
intel types.
v2 by Jani:
- fix the final one too
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7081a49d20cc46b1b1144c83a4e21294d121d8a7.1583766715.git.jani.nikula@intel.com
For icl+, have hw read out to create hw blob of gamma
lut values. icl+ platforms supports multi segmented gamma
mode by default, add hw lut creation for this mode.
This will be used to validate gamma programming using dsb
(display state buffer) which is a tgl specific feature.
v2: -readout code for multisegmented gamma has to come
up with some intermediate entries that aren't preserved
in hardware (Jani N)
-linear interpolation (Ville)
-moved common code to check gamma_enable to specific funcs,
since icl doesn't support that
v3: -use u16 instead of __u16 [Jani N]
-used single lut [Jani N]
-improved and more readable for loops [Jani N]
-read values directly to actual locations and then fill gaps [Jani N]
-moved cleaning to patch 1 [Jani N]
-renamed icl_read_lut_multi_seg() to icl_read_lut_multi_segment to
make it similar to icl_load_luts()
-renamed icl_compute_interpolated_gamma_blob() to
icl_compute_interpolated_gamma_lut_values() more sensible, I guess
v4: -removed interpolated func for creating gamma lut values
-removed readouts of fine and coarse segments, failure to read PAL_PREC_DATA
correctly
v5: -added gamma_enable check inside read_luts()
v6: -renamed intel_color_lut_entry_equal() to intel_color_lut_entries_equal() [Ville]
-changed if-else to switch [Ville]
-removed intel_color_lut_entry_multi_equal() [Ville]
v7: -checkpatch warnings
v8: -rebased
v9: -rebased, aligned with Ville's style of gamma cleanup
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317135736.14305-1-swati2.sharma@intel.com
As we have already enabled supported infrastructure for
non-contiguous pipe fusing in driver, we don't require non-contiguous
pipe_mask check anymore.
It is an unlike condition, it make sense to remove this condition.
changes since RFC:
- using intel_pipe_mask_is_valid() function to check integrity of
pipe_mask. [Ville]
v2:
- simplify condition in intel_pipe_mask_is_valid(). [Ville]
v3:
- removed non-contiguous pipe fusing check. [Lucas]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318094448.26239-1-anshuman.gupta@intel.com
On running several back to back perf capture sessions involving closing
and opening the perf stream, invalid OA reports are seen in the
beginning of the OA buffer in some sessions. Fix this by invalidating OA
TLB when the perf stream is closed or disabled on gen12.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 00a7f0d715 ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309211057.38575-1-umesh.nerlige.ramappa@intel.com
In order to better respond to new heartbeat intervals given via sysfs,
always reprogramme an active heartbeat upon change (i.e. use
mod_delayed_work to reschedule rather than queue_delayed_work which
ignores an already active work.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317163208.30010-1-chris@chris-wilson.co.uk
On Gen11 powergating half the execution units is a functional
requirement when using the VME samplers. Not fullfilling this
requirement can lead to hangs.
This unfortunately plays fairly poorly with the NOA requirements. NOA
requires a stable power configuration to maintain its configuration.
As a result using OA (and NOA feeding into it) so far has required us
to use a power configuration that can work for all contexts. The only
power configuration fullfilling this is powergating half the execution
units.
This makes performance analysis for 3D workloads somewhat pointless.
Failing to find a solution that would work for everybody, this change
introduces a new i915-perf stream open parameter that punts the
decision off to userspace. If this parameter is omitted, the existing
Gen11 behavior remains (half EU array powergating).
This change takes the initiative to move all perf related sseu
configuration into i915_perf.c
v2: Make parameter priviliged if different from default
v3: Fix context modifying its sseu config while i915-perf is enabled
v4: Always consider global sseu a privileged operation (Tvrtko)
Override req_sseu point in intel_sseu_make_rpcs() (Tvrtko)
Remove unrelated changes (Tvrtko)
v5: Some typos (Tvrtko)
Process sseu param in read_properties_unlocked() (Tvrtko)
v6: Actually commit the bits from v5...
Fixup some checkpath warnings
v7: Only compare engine uabi field (Chris)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317132222.2638719-3-lionel.g.landwerlin@intel.com
A little bit of history :
Back when i915-perf was introduced (4.13), there was no way to
dynamically add new OA configurations to i915. Only the generated
configs baked in at build time were allowed.
It quickly became obvious that we would need to allow applications
to upload their own configurations, for instance to be able to test
new ones, and so by the next stable version (4.14) we added uAPIs
to allow uploading new configurations.
When adding that capability, we took the opportunity to remove most
HW configurations except the TestOa one which is a configuration
IGT would rely on to verify that the HW is outputting correct
values. At the time it made sense to have that confiuration in at
the same time a given HW platform added to the i915-perf driver.
Now that IGT has become the reference point for HW configurations (see
commit 53f8f541ca ("lib: Add i915_perf library"), previously this was
located in the GPUTop repository), the need for having those
configurations in i915-perf is gone.
On the Mesa side, we haven't relied on this test configuration for a
while. The MDAPI library always required 4.14 feature level and always
loaded its configuration into i915.
I'm sure nobody will miss this generated stuff in i915 :)
v2: Fix selftests by creating an empty config
v3: Fix unlocking on allocation error (Dan Carpenter)
v4: Fixup checkpatch warnings
v5: Fix incorrect unlock in error path (Umesh)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317132222.2638719-1-lionel.g.landwerlin@intel.com
Apparently we do try and attach a fence to an invalid vma (during
execbuf) so we cannot simply assert it never happens and report EINVAL
instead.
Fixes: dec9cf9ee8 ("drm/i915/gt: Pull restoration of GGTT fences underneath the GT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316205450.15843-1-chris@chris-wilson.co.uk
Since we always reload the fence register state on runtime resume,
having it explicitly in the S0ix resume code is redundant. Indeed, it
is not even being used!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316113846.4974-3-chris@chris-wilson.co.uk
The residual w/a batch is causing system instablity on Ivybridge and
Baytrail under some workloads, so disable until resolved.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1405
Fixes: 47f8253d2b ("drm/i915/gen7: Clear all EU/L3 residual contexts")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311103640.26572-1-chris@chris-wilson.co.uk
We have a few TGL machines in our CI and it is mostly green with
failures in tests that will not impact future Linux installations.
Also there is no warnings, errors, flickering or any visual defects
while doing ordinary tasks like browsing and editing documents in a
dual monitor setup.
As a reminder i915.require_force_probe was created to protect
future Linux installation's iso images that might contain a
kernel from the enabling time of the new platform. Without this
protection most of linux installation was recommending
nomodeset option during installation that was getting stick
there after installation.
Reference: https://intel-gfx-ci.01.org/tree/drm-tip/fi-tgl-u.html
Reference: https://intel-gfx-ci.01.org/tree/drm-tip/shard-tglb.html
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218230822.66801-1-jose.souza@intel.com
This workaround appears under two different numbers (and with somewhat
confused stepping applicability on ICL). Ultimately it appears we
should just implement this for all stepping of ICL and EHL.
Note that this is identical to Wa_1407928979:tgl that already exists in
our driver too...yet another number referencing the same actual
workaround.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311162300.1838847-7-matthew.d.roper@intel.com
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
The bspec description for this workaround tells us to program
0xFFFF_FFFF into both FBC_RT_BASE_ADDR_REGISTER_* registers, but we've
previously found that this leads to failures in CI. Our suspicion is
that the failures are caused by this valid turning on the "address valid
bit" even though we're intentionally supplying an invalid address.
Experimentation has shown that setting all bits _except_ for the
RT_VALID bit seems to avoid these failures.
v2:
- Mask off the RT_VALID bit. Experimentation with CI trybot indicates
that this is necessary to avoid reset failures on BCS.
v3:
- Program RT_BASE before RT_BASE_UPPER so that the valid bit is turned
off by the first write. (Chris)
Bspec: 11388
Bspec: 33451
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311162300.1838847-4-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
On gen11 the XY_FAST_COPY_BLT command has some size restrictions on its
usage. Although this instruction is mainly used by userspace, i915 also
uses it to copy object contents during some selftests, so let's ensure
the restrictions are followed.
Bspec: 6544
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311162300.1838847-3-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The bspec documents multiple MCR ranges; make sure they're all captured
by the driver.
Bspec: 13991, 52079
Fixes: 592a7c5e08 ("drm/i915: Extend non readable mcr range")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311162300.1838847-2-matthew.d.roper@intel.com
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
During driver unload, we have many asserts that we have released our
bookkeeping structs and are idle. In some cases, these struct are
protected by RCU and we do not release them until after an RCU grace
period.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 130a95e909 ("drm/i915/gem: Consolidate ctx->engines[] release")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312115307.16460-1-chris@chris-wilson.co.uk
Since the relocations are no longer performed under a global
struct_mutex, or any other lock, that is also held by pagefault handlers,
we can relax and allow our fast path to take a fault. As we no longer
need to abort the fast path for lock avoidance, we no longer need the
slow path handling at all.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311160310.26711-1-chris@chris-wilson.co.uk
Allow super long OpenCL workloads which cannot be preempted within
the default timeout to run out of the box.
v2:
* Make it stick out more and apply only to RCS. (Chris)
v3:
* Mention platform override in kconfig. (Joonas)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Mrozek <michal.mrozek@intel.com>
Cc: <stable@vger.kernel.org> # v5.6+
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michal Mrozek <Michal.mrozek@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312115748.29970-1-tvrtko.ursulin@linux.intel.com
When applying the context-barrier, we only care about the current
engines, as the next set of engines will be naturally after the barrier.
So we can skip holding the ctx->engines_mutex while constructing the
request by taking a sneaky reference to the i915_gem_engines instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311221739.30375-2-chris@chris-wilson.co.uk
Gen12 hardware supports HDMI audio pixel clocks of 296.7/297Mhz
and 593.4/594Mhz. Add the missing rates and add logic to ignore
them if running on older hardware.
Bspec: 49333
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310162338.9387-1-kai.vehmanen@linux.intel.com
Record the initial active element we use when building the next ELSP
submission, so that we can compare against it latter to see if there's
no change.
Fixes: 44d0a9c05b ("drm/i915/execlists: Skip redundant resubmission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311092624.10012-2-chris@chris-wilson.co.uk
Avoid angering kcsan by serialising the read of the pm_events with the
write in rps_disable_interrupts.
[ 6268.713419] BUG: KCSAN: data-race in intel_rps_park [i915] / rps_work [i915]
[ 6268.713437]
[ 6268.713449] write to 0xffff8881eda8efac of 4 bytes by task 1127 on cpu 3:
[ 6268.713680] intel_rps_park+0x136/0x260 [i915]
[ 6268.713905] __gt_park+0x61/0xa0 [i915]
[ 6268.714128] ____intel_wakeref_put_last+0x42/0x90 [i915]
[ 6268.714352] __intel_wakeref_put_work+0xd3/0xf0 [i915]
[ 6268.714369] process_one_work+0x3b1/0x690
[ 6268.714384] worker_thread+0x80/0x670
[ 6268.714398] kthread+0x19a/0x1e0
[ 6268.714412] ret_from_fork+0x1f/0x30
[ 6268.714423]
[ 6268.714435] read to 0xffff8881eda8efac of 4 bytes by task 950 on cpu 2:
[ 6268.714664] rps_work+0xc2/0x680 [i915]
[ 6268.714679] process_one_work+0x3b1/0x690
[ 6268.714693] worker_thread+0x80/0x670
[ 6268.714707] kthread+0x19a/0x1e0
[ 6268.714720] ret_from_fork+0x1f/0x30
v2: Mark all reads and writes of rpm->pm_events.
The flow of enabling/disabling rps is stronly ordered, so the writes and
interrupt generation are also strongly ordered -- just this may not be
visible to the compiler, so provide annotations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311092624.10012-1-chris@chris-wilson.co.uk
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311073256.6535-1-tiwai@suse.de
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hotplug.c.
In some cases, this involves extracting the drm_i915_private pointer from
the drm_device struct to be used in the logging macros.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3dfda89ab4a234f299ada77abd14163cef3f8bd4.1583766715.git.jani.nikula@intel.com
The two files have been duplicated under the gt/ subdir and since there
are not apparent users looking for them at the old location lets simply
remove them and duplicated code.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310164733.26487-1-tvrtko.ursulin@linux.intel.com
As a virtual engine may change the rq->engine to point to the active
request in flight, we need to warn the compiler that an active request's
engine is volatile.
[ 95.017686] write (marked) to 0xffff8881e8386b10 of 8 bytes by interrupt on cpu 2:
[ 95.018123] execlists_dequeue+0x762/0x2150 [i915]
[ 95.018539] __execlists_submission_tasklet+0x48/0x60 [i915]
[ 95.018955] execlists_submission_tasklet+0xd3/0x170 [i915]
[ 95.018986] tasklet_action_common.isra.0+0x42/0xa0
[ 95.019016] __do_softirq+0xd7/0x2cd
[ 95.019043] irq_exit+0xbe/0xe0
[ 95.019068] irq_work_interrupt+0xf/0x20
[ 95.019491] i915_request_retire+0x2c5/0x670 [i915]
[ 95.019937] retire_requests+0xa1/0xf0 [i915]
[ 95.020348] engine_retire+0xa1/0xe0 [i915]
[ 95.020376] process_one_work+0x3b1/0x690
[ 95.020403] worker_thread+0x80/0x670
[ 95.020429] kthread+0x19a/0x1e0
[ 95.020454] ret_from_fork+0x1f/0x30
[ 95.020476]
[ 95.020498] read to 0xffff8881e8386b10 of 8 bytes by task 8909 on cpu 3:
[ 95.020918] __i915_request_commit+0x177/0x220 [i915]
[ 95.021329] i915_gem_do_execbuffer+0x38c4/0x4e50 [i915]
[ 95.021750] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[ 95.021784] drm_ioctl_kernel+0xe4/0x120
[ 95.021809] drm_ioctl+0x297/0x4c7
[ 95.021832] ksys_ioctl+0x89/0xb0
[ 95.021865] __x64_sys_ioctl+0x42/0x60
[ 95.021901] do_syscall_64+0x6e/0x2c0
[ 95.021927] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310142403.5953-1-chris@chris-wilson.co.uk
When being used across multiple real engines inside a virtual engine,
the intel_context.inflight is updated atomically, and so we must
annotate the racy read from outside the owning context.
[11142.482846] BUG: KCSAN: data-race in __execlists_submission_tasklet [i915] / __execlists_submission_tasklet [i915]
[11142.482867]
[11142.482878] write (marked) to 0xffff8881f257b5e0 of 8 bytes by interrupt on cpu 2:
[11142.483107] __execlists_submission_tasklet+0x1d33/0x2120 [i915]
[11142.483336] execlists_submission_tasklet+0xd3/0x170 [i915]
[11142.483355] tasklet_action_common.isra.0+0x42/0xa0
[11142.483371] __do_softirq+0xd7/0x2cd
[11142.483384] irq_exit+0xbe/0xe0
[11142.483401] do_IRQ+0x51/0x100
[11142.483424] ret_from_intr+0x0/0x1c
[11142.483446] do_idle+0x133/0x1f0
[11142.483465] cpu_startup_entry+0x14/0x16
[11142.483483] start_secondary+0x120/0x180
[11142.483498] secondary_startup_64+0xa4/0xb0
[11142.483512]
[11142.483528] read to 0xffff8881f257b5e0 of 8 bytes by interrupt on cpu 1:
[11142.483755] __execlists_submission_tasklet+0x14e/0x2120 [i915]
[11142.483981] execlists_submission_tasklet+0xd3/0x170 [i915]
[11142.483999] tasklet_action_common.isra.0+0x42/0xa0
[11142.484014] __do_softirq+0xd7/0x2cd
[11142.484028] do_softirq_own_stack+0x2a/0x40
[11142.484046] do_softirq.part.0+0x26/0x30
[11142.484071] __local_bh_enable_ip+0x46/0x50
[11142.484299] i915_gem_do_execbuffer+0x39c1/0x4e50 [i915]
[11142.484528] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[11142.484546] drm_ioctl_kernel+0xe4/0x120
[11142.484559] drm_ioctl+0x297/0x4c7
[11142.484572] ksys_ioctl+0x89/0xb0
[11142.484586] __x64_sys_ioctl+0x42/0x60
[11142.484610] do_syscall_64+0x6e/0x2c0
[11142.484627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310141320.24149-1-chris@chris-wilson.co.uk
Platforms without fences don't have FBC host tracking and those
registers are marked as reserved in those platforms.
v2: checking num_fences to write to FBC fence registers (Ville)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306185833.53984-2-jose.souza@intel.com
i915 can enable aux device nodes for DP MST by calling
drm_dp_mst_connector_late_register()/
drm_dp_mst_connector_early_unregister(),
so let's hook that up.
Changes since v1:
* Call intel_connector_register/unregister() from
intel_dp_mst_connector_late_register/unregister() so we don't lose
error injection - Ville Syrjälä
Changes since v2:
* Don't forget to clean up if intel_connector_register() fails - Ville
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310195122.1590925-1-lyude@redhat.com
Always wait on the start of the signaler request to reduce the problem
of dequeueing the bonded pair too early -- we want both payloads to
start at the same time, with no latency, and yet still allow others to
make full use of the slack in the system. This reduce the amount of time
we spend waiting on the semaphore used to synchronise the start of the
bonded payload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-3-chris@chris-wilson.co.uk
gmbus/aux may be clocked by cdclk, thus we should make sure no
transfers are ongoing while the cdclk frequency is being changed.
We do that by simply grabbing all the gmbus/aux mutexes. No one
else should be holding any more than one of those at a time so
the lock ordering here shouldn't matter.
v2: Use mutex_lock_nest_lock() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302174442.5803-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The low level read_lut() functions don't need the entire crtc state
as they know exactly what they're reading. Just need to pass in the
crtc to get at the pipe. This now neatly mirrors the load_lut()
direction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-10-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
PIPEGCMAX is a 11.6 (or 1.16 if you will) value. Ie. it can
represent a value of 1.0 when the maximum we can store in the
software LUT is 0.ffff. Clamp the value so that it gets
saturated to the max the uapi supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-9-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
A variable called 'i' having an unsigned type is just looking for
trouble, and using a sized type generally makes no sense either.
Change all of them to just plain old int. And do the same for some
'lut_size' variables which generally provide the loop end codition
for 'i'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-7-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Only load the CGM CSC based on the cgm_mode bit like we
do with the gamma/degamma LUTs. And make the function
naming and arguments consistent as well.
TODO: the code to convert the coefficients look totally
bogus. IIRC CHV uses two's complement format but the code
certainly doesn't generate that, so probably negative
coefficients are totally busted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-2-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
During i915_request_retire() we decouple the i915_request.hwsp_seqno
from the intel_timeline so that it may be freed before the request is
released. However, we need to warn the compiler that the pointer may
update under its nose.
[ 171.438899] BUG: KCSAN: data-race in i915_request_await_dma_fence [i915] / i915_request_retire [i915]
[ 171.438920]
[ 171.438932] write to 0xffff8881e7e28ce0 of 8 bytes by task 148 on cpu 2:
[ 171.439174] i915_request_retire+0x1ea/0x660 [i915]
[ 171.439408] retire_requests+0x7a/0xd0 [i915]
[ 171.439640] engine_retire+0xa1/0xe0 [i915]
[ 171.439657] process_one_work+0x3b1/0x690
[ 171.439671] worker_thread+0x80/0x670
[ 171.439685] kthread+0x19a/0x1e0
[ 171.439701] ret_from_fork+0x1f/0x30
[ 171.439721]
[ 171.439739] read to 0xffff8881e7e28ce0 of 8 bytes by task 696 on cpu 1:
[ 171.439990] i915_request_await_dma_fence+0x162/0x520 [i915]
[ 171.440230] i915_request_await_object+0x2fe/0x470 [i915]
[ 171.440467] i915_gem_do_execbuffer+0x45dc/0x4c20 [i915]
[ 171.440704] i915_gem_execbuffer2_ioctl+0x2c3/0x580 [i915]
[ 171.440722] drm_ioctl_kernel+0xe4/0x120
[ 171.440736] drm_ioctl+0x297/0x4c7
[ 171.440750] ksys_ioctl+0x89/0xb0
[ 171.440766] __x64_sys_ioctl+0x42/0x60
[ 171.440788] do_syscall_64+0x6e/0x2c0
[ 171.440802] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309110934.868-1-chris@chris-wilson.co.uk
The UNSLICE_UNIT_LEVEL_CLKGATE and UNSLICE_UNIT_LEVEL_CLKGATE2 registers
that we update in a few engine workarounds are not masked registers
(i.e., we don't have to write a mask bit in the top 16 bits when
updating one of the lower 16 bits). As such, these workarounds should
be applied via wa_write_or() rather than wa_masked_en()
v2:
- Rebase
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
References: https://github.com/ClangBuiltLinux/linux/issues/918
Fixes: 50148a25f8 ("drm/i915/tgl: Move and restrict Wa_1408615072")
Fixes: 3551ff9287 ("drm/i915/gen11: Moving WAs to rcs_engine_wa_init()")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306171139.1414649-1-matthew.d.roper@intel.com
Fix the following kerneldoc warning and while at it also the doc for the
corresponding vfunc hook.
$ make htmldocs 2>&1 > /dev/null | grep i915
./drivers/gpu/drm/i915/display/intel_dpll_mgr.h:285: warning: Function parameter or member 'get_freq' not described in 'intel_shared_dpll_funcs'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304150918.25473-1-imre.deak@intel.com
Be sure to wait for the vma to be in place before we tell the GPU to
execute from the wa batch. Since initialisation is mostly synchronous
(or rather at some point during start up we will need to sync anyway),
we can affort to do an explicit i915_vma_sync() during wa batch
construction rather than check for a required await on every context
switch. (We don't expect to change the wa bb at run time so paying the
cost once up front seems preferrable.)
Fixes: ee2413eeed ("drm/i915: Add mechanism to submit a context WA on ring submission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307122425.29114-1-chris@chris-wilson.co.uk
If the cacheline may still be busy, atomically mark it for future
release, and only if we can determine that it will never be used again,
immediately free it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392
Fixes: ebece75392 ("drm/i915: Keep timeline HWSP allocated until idle across the system")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk
If we stop filling the ELSP due to an incompatible virtual engine
request, check if we should enable the timeslice on behalf of the queue.
This fixes the case where we are inspecting the last->next element when
we know that the last element is the last request in the execution queue,
and so decided we did not need to enable timeslicing despite the intent
to do so!
Fixes: 8ee36e048c ("drm/i915/execlists: Minimalistic timeslicing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk
Due to the ordering of cmpxchg()/dma_fence_signal() inside node_retire(),
we must also use the xchg() as our primary memory barrier to flush the
outstanding callbacks after expected completion of the i915_active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306133852.3420322-1-chris@chris-wilson.co.uk
This workaround is to disable FF DOP Clock gating. The fix
in B0 was backed out due to timing reasons and decided to
be made permanent.
Bspec: 52890
Signed-off-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305181204.28856-1-swathi.dhanavanthri@intel.com
On some platforms such as Elkhart Lake, although we may use DDI D
to drive a connector, we have to use PHY A (Combo Phy PORT A) to
detect the hotplug interrupts as per the spec because there is no
one-to-one mapping between DDIs and PHYs. Therefore, use the
function intel_port_to_phy() which contains the logic for such
mapping(s) to find the correct hpd_pin.
This change should not affect other platforms as there is always
a one-to-one mapping between DDIs and PHYs.
v2:
- Convert the case statements to use PHYs instead of PORTs (Jani)
v3:
- Refactor the function to reduce the number of return statements by
lumping all the case statements together except PHY_F which needs
special handling (Jose)
v4:
- Add a comment describing how the HPD pin value associated with any
port can be retrieved using port or phy enum value. (Jani)
v5:
- Use case ranges instead of individual labels and also normalize the
return statement by adding -PHY_A to the expression (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304234240.12062-1-vivek.kasireddy@intel.com
Depending on RNG we might try to fill an 8G region for every possible
order, using the smallest possible chunk size of 4K, which seems to be
very slow. Try to remedy the situation by adding an overall timeout for
the test, while also selecting each order level in a random fashion.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1310
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305204711.217783-2-matthew.auld@intel.com
Check the edge case where batch_start_offset sits exactly on the batch
size.
v2: add new range_overflows variant to capture the special case where
the size is permitted to be zero, like with batch_len.
v3: other way around. the common case is the exclusive one which should
just be >=, with that we then just need to convert the three odd ball
cases that don't apply to use the new inclusive _end version.
Testcase: igt/gem_exec_params/invalid-batch-start-offset
Fixes: 0b5372727b ("drm/i915/cmdparser: Use cached vmappings")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306094735.258285-1-matthew.auld@intel.com
We only need to serialise the multiple pinning during the eb_reserve
phase. Ideally this would be using the vm->mutex as an outer lock, or
using a composite global mutex (ww_mutex), but at the moment we are
using struct_mutex for the group.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1381
Fixes: 003d8b9143 ("drm/i915/gem: Only call eb_lookup_vma once during execbuf ioctl")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306071614.2846708-3-chris@chris-wilson.co.uk
We only call i915_schedule() when we know we have changed the priority
on a request and so require to propagate any change in priority to its
signalers (for PI). By unconditionally checking all of our signalers, we
avoid skipping changes made prior to construction of the request (as the
request may be waited upon before submission when used in parallel).
References: https://gitlab.freedesktop.org/drm/intel/issues/1318
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306071614.2846708-2-chris@chris-wilson.co.uk
The alignment is u64, and yet is_power_of_2() assumes unsigned long,
which might give different results between 32b and 64b kernel.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
The release method will undo what we did at creation, and so we
shouldn't care if we have pages or not. Fixes a small leak in the
mock_phys selftest.
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305204258.216302-1-matthew.auld@intel.com
On gen7 and gen7.5 devices, there could be leftover data residuals in
EU/L3 from the retiring context. This patch introduces workaround to clear
that residual contexts, by submitting a batch buffer with dedicated HW
context to the GPU with ring allocation for each context switching.
This security mitigation changes does not triggers any performance
regression. Performance is on par with current drm-tips.
v2: Add igt generated header file for CB kernel assembled with Mesa tool
and addressed use of Kernel macro for ptr_align comment.
v3: Resolve Sparse warnings with newly generated, and imported CB
kernel.
v4: Include new igt generated CB kernel for gen7 and gen7.5. Also
add code formatting and compiler warnings changes (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Acked-by: Chris Wilson <chris@chris-wilso.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306000957.2836150-2-chris@chris-wilson.co.uk
This patch adds framework to submit an arbitrary batchbuffer on each
context switch to clear residual state for render engine on Gen7/7.5
devices.
The idea of always emitting the context and vm setup around each request
is primary to make reset recovery easy, and not require rewriting the
ringbuffer. As each request would set up its own context, leaving it to
the HW to notice and elide no-op context switches, we could restart the
ring at any point, and reorder the requests freely.
However, to avoid emitting clear_residuals() between consecutive requests
in the ringbuffer of the same context, we do want to track the current
context in the ring. In doing so, we need to be careful to only record a
context switch when we are sure the next request will be emitted.
This security mitigation change does not trigger any performance
regression. Performance is on par with current mainline/drm-tip.
v2: Update vm_alias params to point to correct address space "vm" due to
changes made in the patch "f21613797bae98773"
v3-v4: none
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306000957.2836150-1-chris@chris-wilson.co.uk
Teach gvt to use intel_gt directly as it currently assumes direct HW
access.
[Zhenyu: rebase, fix compiling]
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-3-zhenyuw@linux.intel.com
Stop trying to escape out of the gvt layer to find the engine that we
initially setup for use with gvt. Record the engines during initialisation
and use them henceforth.
add/remove: 1/4 grow/shrink: 22/28 up/down: 341/-1410 (-1069)
[Zhenyu: rebase, fix nonpriv register check fault, fix gvt engine
thread run failure.]
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-2-zhenyuw@linux.intel.com
Remove extra chatty message for debugfs scan_nonprivbb which is used
to enable scan for non privileged batch on specific engine. Just write
target i915 engine mask instead.
Cc: Ding Zhuocheng <zhuocheng.ding@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200304032307.2983-1-zhenyuw@linux.intel.com
Commit c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
added the support on CFL. The vgpu emulation hotplug support on CFL was
supposed to be included in that patch. Without the vgpu emulation
hotplug support, the dma-buf based display gives us a blur face.
So fix this issue by adding the vgpu emulation hotplug support on CFL.
Fixes: c3b5a8430d ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200227010041.32248-1-tina.zhang@intel.com
Requests within a timeline are ordered by that timeline, so awaiting for
the start of a request within the timeline is a no-op. This used to work
by falling out of the mutex_trylock() as the signaler and waiter had the
same timeline and not returning an error.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305134822.2750496-1-chris@chris-wilson.co.uk
Fix the inverted test to emit the wait on the end of the previous
request if we /haven't/ already.
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305104210.2619967-1-chris@chris-wilson.co.uk
Converting error to debug print if sink fails to configure scrambling or
TMDS bit clock ratio. In this case, we are timing out while disabling
the scrambling and setting the SCDC ratio, as there is no response
to the I2C SCDC write from the sink device. Error isn't due to something
wrong done from driver side.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302213807.6488-1-swati2.sharma@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
We are mistakenly skipping transition watermarks on glk. Fix
up the condition for glk, and toss in the w/a name from
the database.
v2: Reorder the ipc enabled vs. platform check to be more sensible
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-3-ville.syrjala@linux.intel.com
Currently we're comparing the watermarks between the old and new states
before we've fully computed the new watermarks. In particular
skl_build_pipe_wm() will not account for the amount of ddb space we'll
have. That information is only available during skl_compute_ddb()
which will proceed to zero out any watermark level exceeding the
ddb allocation. If we're short on ddb space this will end up
adding the plane to the state due erronously determining that the
watermarks have changed. Fix the problem by deferring
skl_wm_add_affected_planes() until we have the final watermarks
computed.
Noticed this when trying enable transition watermarks on glk.
We now computed the trans_wm as 28, but we only had 14 blocks
of ddb, and thus skl_compute_ddb() ended up disabling the cursor
trans_wm every time. Thus we ended up adding the cursor to every
commit that didn't actually affect the cursor at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The hardware never sees the uv_wm values (apart from
uv_wm.min_ddb_alloc affecting the ddb allocation). Thus there
is no point in comparing uv_wm to determine if we need to
reprogram the watermark registers. So let's check only the
rgb/y watermark in skl_plane_wm_equals(). But let's leave
a comment behind so that the next person reading this doesn't
get as confused as I did when I added this check.
If the ddb allocation ends up changing due to uv_wm
skl_ddb_add_affected_planes() takes care of adding the plane
to the state.
TODO: we should perhaps just eliminate uv_wm from the state
and simply track the min_ddb_alloc for uv instead.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228203552.30273-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Enable FtrPerCtxtPreemptionGranularityControl bit and select thread-
group as the default preemption level.
v2:
* Remove register whitelisting (Rafael, Tony).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: piotr.zdunowski@intel.com
Cc: michal.mrozek@intel.com
Cc: Tony Ye <tony.ye@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Acked-by: Rafael Antognolli <rafael.antognolli@intel.com>
Acked-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tony Ye <tony.ye@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304153144.10675-1-tvrtko.ursulin@linux.intel.com
The Thundersoft TST178 tablet uses a DSI panel with an external PWM
controller (as all DSI panels do). But unlike other DSI panels a duty-cycle
of 100% turns the backlight off and 0% sets it to maximum brightness.
I've checked the VBT and there is a BDB_LVDS_BACKLIGHT section, but
it does not set the active_low_pwm flag. This tablet re-uses the main
PCI vendor and product ids for the subsystem ids, so I see no other option
then to add a DMI based quirk to fix this.
Note that the PWM backlight code in intel_panel.c currently does not honor
the vbt.active_low_pwm flag, but that does not matter in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-2-hdegoede@redhat.com
Use intel_panel_compute_brightness() from pwm_setup_backlight() so that
we correctly take i915_modparams.invert_brightness and/or
QUIRK_INVERT_BRIGHTNESS into account when setting + getting the initial
brightness value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-1-hdegoede@redhat.com
Trying to use i915_request_skip() prior to i915_request_add() causes us
to try and fill the ring upto request->postfix, which has not yet been
set, and so may cause us to memset() past the end of the ring.
Instead of skipping the request immediately, just flag the error on the
request (only accepting the first fatal error we see) and then clear the
request upon submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304121849.2448028-1-chris@chris-wilson.co.uk
intel_ddi_clock_get() tests the DPLL ID against DPLL_ID_ICL_TBTPLL (2)
to determine whether to try to descend into a TBT-specific handler.
However this test will also be true when DPLL4 on EHL is used since that
shares the same DPLL ID (2).
Add an extra check to ensure the PHY is actually a Type-C PHY before
descending into the TBT handling. This should ensure EHL still takes
the correct code path and somewhat future-proof the code as well.
v2: Drop the gen+ check since only gen11+ platforms can have Type-C
outputs. (Imre)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1369
Fixes: 45e4728b87 ("drm/i915: Move DPLL frequency calculation to intel_dpll_mgr.c")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303195043.959913-1-matthew.d.roper@intel.com
drivers/gpu/drm/i915/gvt/gvt.c:264:6: error: no previous prototype for ‘intel_gvt_clean_device’ [-Werror=missing-prototypes]
drivers/gpu/drm/i915/gvt/gvt.c:301:5: error: no previous prototype for ‘intel_gvt_init_device’ [-Werror=missing-prototypes]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304002331.2126072-1-chris@chris-wilson.co.uk
The X1 Extreme is one of the systems that lies about which backlight
interface that it uses in its VBIOS as PWM backlight controls don't work
at all on this machine. It's possible that this panel could be one of
the infamous ones that can switch between PWM mode and DPCD backlight
control mode, but we haven't gotten any more details on this from Lenovo
just yet. For the time being though, making sure the backlight 'just
works' is a bit more important.
So, add a quirk to force DPCD backlight controls on for these systems
based on EDID (since this panel doesn't appear to fill in the device ID).
Hopefully in the future we'll figure out a better way of probing this.
Changes since v2:
* The bugzilla URL is deprecated, bug reporting happens on gitlab now.
Update the messages we print to reflect this
* Also, take the opportunity to move FDO_BUG_URL out of i915_utils.c and
into i915_utils.h so that other places which print things that aren't
traditional errors but are worth filing bugs about, can actually use
it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303215320.93491-1-lyude@redhat.com
The whole point of using OUIs is so that we can recognize certain
devices and potentially apply quirks for them. Normally this should work
quite well, but there appears to be quite a number of laptop panels out
there that will fill the OUI but not the device ID. As such, for devices
like this I can't imagine it's a very good idea to try relying on OUIs
for applying quirks. As well, some laptop vendors have confirmed to us
that their panels have this exact issue.
So, let's introduce the ability to apply DP quirks based on EDID
identification. We reuse the same quirk bits for OUI-based quirks, so
that callers can simply check all possible quirks using
drm_dp_has_quirk().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-2-lyude@redhat.com
DP shim's config_stream_type considered to be succeeded when
return value of intel_dp_hdcp2_write_msg() equals to size of
message to be written, it makes config_stream_type to return
a zero success value in order to succeed the HDCP auth.
v2:
- config_stream_type() returns 0 on success. [Ram]
CC: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303073838.25871-1-anshuman.gupta@intel.com
HDCP Repeater initializes seq_num_V to 0 at the beginning of
hdcp Session i.e. after AKE_init received, refer
HDCP 2.2 Spec HDMI PAGE 19, DP PAGE 20.
HDCP 2.2 Comp specs 1B-06 test verifies that whether DUT
considers failure of authentication if the repeater provides a
non-zero value in seq_num_V in the first,
RepeaterAuth_Send_ReceiverID_List message.
Make sure that HDCP repeater initializes seq_num_V to zero at
beginning of session i.e. after AKE_Init, fail the Auth if
there is non zero seq_num_V.
v2:
- Used existing hdcp2_encrypted flag instead of
declaring new flag. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200220123217.23635-2-anshuman.gupta@intel.com
As we no longer stash anything inside i915_vma under the exclusive
protection of struct_mutex, we do not need to revoke the i915_vma
stashes before dropping struct_mutex to handle pagefaults. Knowing that
we must drop the struct_mutex while keeping the eb->vma around, means
that we are required to hold onto to the object reference until we have
marked the vma as active.
Fixes: 155ab8836c ("drm/i915: Move object close under its own lock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-3-chris@chris-wilson.co.uk
For our convenience, and to avoid frequent allocations, we placed some
lists we use for execbuf inside the common i915_vma struct. As we look
to parallelise execbuf, such fields guarded by the struct_mutex BKL must
be pulled under local control. Instead of using the i915_vma as our
primary means of tracking the user's list of objects and their virtual
mappings, we use a local eb_vma with the same lists as before (just now
local not global).
This should allow us to only perform the lookup of vma used for
execution once during the execbuf ioctl, as currently we need to remove
our secrets from inside i915_vma everytime we drop the struct_mutex as
another execbuf may use the shared locations.
Once potential user visible consequence is that we can remove the
requirement that the execobj[] be unique, and only require that they do
not conflict (i.e. you cannot softpin the same object into two locations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-2-chris@chris-wilson.co.uk
With the goal of removing the serialisation from around execbuf, we will
no longer have the privilege of there being a single execbuf in flight
at any time and so will only be able to inspect the user's flags within
the carefully controlled execbuf context. i915_gem_evict_for_node() is
the only user outside of execbuf that currently peeks at the flag to
convert an overlapping softpinned request from ENOSPC to EINVAL. Retract
this nicety and only report ENOSPC if the location is in current use,
either due to this execbuf or another.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303204345.1859734-1-chris@chris-wilson.co.uk
Following the changes in the previous patch
"drm/i915/gen11: Moving WAs to rcs_engine_wa_init()" also moving TGL
Wa_1408615072 to rcs_engine_wa_init() this way after a engine
reset it will be reapplied also restricting it to A0 as it is fixed in
B0 stepping.
BSpec: 52890
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302231421.224322-2-jose.souza@intel.com
This are register of render engine, so after a render reset those
would return to the default value and init_clock_gating() is not
called for single engine reset.
So here moving it rcs_engine_wa_init() that will guarantee that this
WAs will not be lost.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302231421.224322-1-jose.souza@intel.com
Static code analysis tool identified struct lrc_timestamp data as being
uninitialized and then data.ce[] is being checked for NULL/negative
value in the error path. Initializing data variable fixes the issue.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303142347.15696-1-aditya.swarup@intel.com
As we have pinned the timeline (using tl->active_count), we can safely
drop the tl->mutex as we wait for what we believe to be the final
request on that timeline. This is useful for ensuring that we do not
block the engine heartbeat by hogging the kernel_context's timeline on a
dead GPU.
References: https://gitlab.freedesktop.org/drm/intel/issues/1364
Fixes: 058179e72e ("drm/i915/gt: Replace hangcheck by heartbeats")
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303140009.1494819-1-chris@chris-wilson.co.uk
The is-closed flag may be added after we have acquired the vma under the
ctx->mutex, but will not take effect until after we release the
vm->mutex. i.e. the flag may be set on the vma as attempt to bind it and
that will cause the vma to be unbound later after we unpin it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303093157.1153887-1-chris@chris-wilson.co.uk
As setup takes a long time, the user may close the context during the
construction of the execbuf. In order to make sure we correctly track
all outstanding work with non-persistent contexts, we need to serialise
the submission with the context closure and mop up any leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303080546.1140508-3-chris@chris-wilson.co.uk
It irks me to use crtc_state_is_legacy_gamma() inside the guts
of the CHV color management code. Let's get rid of it and instead
just consult cgm_mode to figure out if we want to enable the pipe
gamma or the CGM gamma.
Also CHV display engine is based on i965/g4x so we should fall back
to the i965 path when the CGM gamma is not used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107151725.10507-3-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Add intel_vgpu_register() abstraction, rename i915_detect_vgpu() to
intel_vgpu_detect() to match other function naming, un-inline
intel_vgpu_active(), intel_vgpu_has_full_ppgtt() and
intel_vgpu_has_huge_gtt() to reduce header interdependencies.
The i915_vgpu.[ch] filename and intel_vgpu_ prefix discrepancy remains.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227144408.24345-1-jani.nikula@intel.com
has_transcoder() was unused because function which was using it,
intel_display_capture_error_state() defined under
CONFIG_DRM_I915_CAPTURE_ERROR.
Moving has_transcoder() to under CONFIG_DRM_I915_CAPTURE_ERROR.
No functional change.
Fixes: d54c1a513c ("drm/i915: Fix broken transcoder err state")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227175147.11362-1-anshuman.gupta@intel.com
Converts remaining instances of the printk based logging macros in
i915/display/intel_hdcp.c with the struct drm_device based macros
manually.
This is continuation of commit 65833c4638 ("drm/i915/hdcp: conversion
to struct drm_device based logging macros.")
v2:
i915_dev_priv is used instead of drm_device for reusability [JaniN]
v3:
Made it independent from the series.
once instance of dev_priv naming is changed to i915 [Jani N]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212123007.6659-1-ramalingam.c@intel.com
Update to the latest available TGL HuC, which includes changes required
by the media team.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tony Ye <tony.ye@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Tony Ye <tony.ye@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200229012042.27487-1-daniele.ceraolospurio@intel.com
We still need to wait for the initial OA configuration to happen
before we enable OA report writes to the OA buffer.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 15d0ace1f8 ("drm/i915/perf: execute OA configuration from command stream")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1356
Testcase: igt/perf/stream-open-close
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302085812.4172450-7-chris@chris-wilson.co.uk
Different issues with the same fix, so justing adding
Wa_1409142259, Wa_1409252684, Wa_1409217633, Wa_1409207793,
Wa_1409178076 and 1408979724 to the comment so other devs can check if
this Was were implemetend with a simple grep.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-8-jose.souza@intel.com
According to BSpec. Wa_1606931601 applies for all TGL steppings.
This patch moves the WA implementation out of A0 only block of
rcs_engine_wa_init().
The WA is has also been referred to by an alternate name
Wa_1607090982.
Bspec: 46045, 52890
Fixes: 3873fd1a43 ("drm/i915: Use engine wa list for Wa_1607090982")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-4-jose.souza@intel.com
Disable Push Constant buffer addition for TGL.
v2: typos, add additional Wa reference
v3: use REG_BIT macro, move to rcs_engine_wa_init, clean up commit
message.
Bspec: 52890
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-3-jose.souza@intel.com
This will whitelist the HIZ_CHICKEN register so mesa can disable the
optimizations and avoid hang when using D16_UNORM.
v2: moved to the right place and used the right function() (Chris)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-2-jose.souza@intel.com
This workaround the CS not done issue on PIPE_CONTROL.
v2:
- replaced BIT() by REG_BIT() in all GEN7_ROW_CHICKEN2() bits
- shortened the name of the new bit
BSpec: 52890
BSpec: 46218
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227220101.321671-1-jose.souza@intel.com
All platforms using the shared DPLL framework use 3 reference clocks for
their DPLLs: SSC, non-SSC and DSI. For a more unified way across
platforms store the frequency of these ref clocks as part of the DPLL
global state. This also allows us to keep the HW access reading out the
ref clock value separate from the DPLL frequency calculation that
depends on the ref clock.
For now add only the SSC and non-SSC ref clocks, as the pre-ICL DSI code
has its own logic for calculating DPLL parameters instead of the shared
DPLL framework.
v2:
- Apply the ICL combo PHY PLL ref_clock/2 adjustment during the
frequency->PLL param conversion direction as well. (CI shards)
- s/kHZ/kHz/ (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228153328.17842-1-imre.deak@intel.com
The types of PLLs used for HDMI/DP on HSW are WRPLL/LCPLL accordingly,
so use these names to align better with the rest of WRPLL/LCPLL function
names elsewhere.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-9-imre.deak@intel.com
For clarity keep the SKL DPLL ref clock in a variable instead of
open-coding it. Store the value in kHZ units as done on other platforms.
This allows us in a later patch to keep track of the DPLL ref clock in a
more unified way across all platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-8-imre.deak@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
For clarity add a new DPLL specific struct to the i915 device struct and
move all DPLL fields into it. Accordingly remove the dpll_ prefixes, as
the new struct already provides the required namespacing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-4-imre.deak@intel.com
There seems to be a bit of confusing redundancy in a way, how
plane data rate/min cdclk are calculated.
In fact both min cdclk, pixel rate and plane data rate are all
part of the same formula as per BSpec.
However currently we have intel_plane_data_rate, which is used
to calculate plane data rate and which is also used in bandwidth
calculations. However for calculating min_cdclk we have another
piece of code, doing almost same calculation, but a bit differently
and in a different place. However as both are actually part of same
formula, probably would be wise to use plane data rate calculations
as a basis anyway, thus avoiding code duplication and possible bugs
related to this.
Another thing is that I've noticed that during min_cdclk calculations
we account for plane scaling, while for plane data rate, we don't.
crtc->pixel_rate seems to account only for pipe ratio, however it is
clearly stated in BSpec that plane data rate also need to account
plane ratio as well.
So what this commit does is:
- Adds a plane ratio calculation to intel_plane_data_rate
- Removes redundant calculations from skl_plane_min_cdclk which is
used for gen9+ and now uses intel_plane_data_rate as a basis from
there as well.
v2: - Don't use 64 division if not needed(Ville Syrjälä)
- Now use intel_plane_pixel_rate as a basis for calculations both
at intel_plane_data_rate and skl_plane_min_cdclk(Ville Syrjälä)
v3: - Again fix the division macro
- Fix plane_pixel_rate to pixel_rate at intel_plane_pixel_rate
callsites
v4: - Renamed skl_plane_ratio function back(Ville Syrjälä)
v5: - Don't precalculate plane pixel rate for invisible plane,
check for visibility first, as in invisible case it will
have dst_w and dst_h equal to zero, causing divide error.
v6: - Removed useless warn in intel_plane_pixel_rate(Ville Syrjälä)
- Fixed alignment in intel_plane_data_rate(Ville Syrjälä)
- Changed pixel_rate type to be unsigned int in
skl_plane_min_cdclk(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227150935.2107-1-stanislav.lisovskiy@intel.com
Make life a bit simpler by sticking a sentinel at the end of
the dbuf slice arrays. This way we don't need to pass in the
size. Also unify the types (u8 vs. u32) for active_pipes.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The preferred style is to sprinkle commas after each array and
structure initialization, whether or not it happens to be the
last element/member (only exception being sentinel entries which
never have anything after them). This leads to much prettier
diffs if/when new elements/members get added to the end of the
initialization. We're not bound by some ancient silly mandate
to omit the final comma.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
These things can never happen, and probably we'd have oopsed long ago
if they did. Just get rid of this pointless noise in the code.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Supposedly both src coordinates have to even when doing 90/270
degree rotation with RGB565. This is definitely true for the
X coordinate (we just get a black screen when it is odd). My
experiments didn't show any misbehaviour with an odd
Y coordinate, but let's trust the spec and reject that one
as well.
v2: Ignore ccs hsub/vsub
v3: Clarify the CCS special (Maarten)
Deal with tgl+ CCS modifiers where we
do need to look at hsub/vsub
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228160523.1064-1-ville.syrjala@linux.intel.com
Some devices with a builtin panel have the panel mounted upside down,
this is indicated by the rotate_180 bit in the BDB_GENERAL_FEATURES VBT
block.
We store this info in dev_priv->vbt.orientation, use this to set the
connector's orientation property so that fbcon and userspace will show
the image the right way up on devices with an upside-down mounted panel.
This fixes the image being upside-down on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-3-hdegoede@redhat.com
Commit 82daca2975 ("drm/i915: Add "panel orientation" property to the
panel connector, v6.") uses hardware state readback to determine if the
GOP is rotating the image by 180 degrees to compensate for upside-down
mounted panels.
When I wrote that commit I tried to find the VBT bits the GOP used to
decide to rotate the image, but I could not find them. Back then I only
looked at the rotation bits in struct mipi_config and these read 0 on
the 1 BYT device I have with an upside-down mounted panel
(a GP-electronic T701 tablet). While working on a similar problem on a
BYT device with an eDP panel I noticed that the new
intel_dsi_get_panel_orientation() helper which gets used on newer
SoCs (Apollo-Lake, etc.) checks the rotate_180 bit in the
BDB_GENERAL_FEATURES VBT block.
I've checked and this bit indeed is set on the GP-electronic T701 tablet,
so using the generic intel_dsi_get_panel_orientation() helper there does
the right thing without needing any extra readback of hw state.
This commit removes the special handling of the panel orientation for
DSI panels on BYT/CHT devices, bringing the handling in line with the
handling of DSI panels on other devices.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-2-hdegoede@redhat.com
Finish the job started in d28ae3b281 ("drm/i915: split out
intel_dram.[ch] from i915_drv.c") by moving struct dram_dimm_info and
dram_channel_info inside intel_dram.c, the only user of the structs.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227145359.17543-1-jani.nikula@intel.com
Having an array pipe_crc[I915_MAX_PIPES] in struct drm_i915_private
should be an obvious clue this should be located in struct intel_crtc
instead. Make it so.
As a side-effect, fix some errors in indexing pipe_crc with both pipe
and crtc index. And, of course, reduce the size of i915_drv.h.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227161253.15741-1-jani.nikula@intel.com
We monitor the health of the system via periodic heartbeat pulses. The
pulses also provide the opportunity to perform garbage collection.
However, we interpret an incomplete pulse (a missed heartbeat) as an
indication that the system is no longer responsive, i.e. hung, and
perform an engine or full GPU reset. Given that the preemption
granularity can be very coarse on a system, we let the sysadmin override
our legacy timeouts which were "optimised" for desktop applications.
The heartbeat interval can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/heartbeat_interval_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-7-chris@chris-wilson.co.uk
After initialising a preemption request, we give the current resident a
small amount of time to vacate the GPU. The preemption request is for a
higher priority context and should be immediate to maintain high
quality of service (and avoid priority inversion). However, the
preemption granularity of the GPU can be quite coarse and so we need a
compromise.
The preempt timeout can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/preempt_timeout_ms
and can be disabled by setting it to 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-6-chris@chris-wilson.co.uk
When we allow ourselves to sleep before a GPU reset after disabling
submission, even for a few milliseconds, gives an innocent context the
opportunity to clear the GPU before the reset occurs. However, how long
to sleep depends on the typical non-preemptible duration (a similar
problem to determining the ideal preempt-reset timeout or even the
heartbeat interval). As this seems of a hard policy decision, punt it to
userspace.
The timeout can be adjusted using
/sys/class/drm/card?/engine/*/stop_timeout_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-5-chris@chris-wilson.co.uk
We busywait on an inflight request (one that is currently executing on
HW, and so might complete quickly) prior to setting up an interrupt and
sleeping. The trade off is that we keep an expensive CPU core busy in
order to avoid wake up latency: where that trade off should lie is best
left to the sysadmin.
The busywait mechanism can be compiled out with
./scripts/config --set-val DRM_I915_SPIN_REQUEST 0
The maximum busywait duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/ms_busywait_duration_ns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-4-chris@chris-wilson.co.uk
Execlists uses a scheduling quantum (a timeslice) to alternate execution
between ready-to-run contexts of equal priority. This ensures that all
users (though only if they of equal importance) have the opportunity to
run and prevents livelocks where contexts may have implicit ordering due
to userspace semaphores.
The timeslicing mechanism can be compiled out with
./scripts/config --set-val DRM_I915_TIMESLICE_DURATION 0
The timeslice duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/timeslice_duration_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-3-chris@chris-wilson.co.uk
Use the per-engine sysfs directory to let userspace discover the
mmio_base of each engine. Prior to recent generations, the user
accessible registers on each engine are at a fixed offset relative to
each engine -- but require absolute addressing. As the absolute address
depends on the actual physical engine, this is not always possible to
determine from userspace (for example icl may expose vcs1 or vcs2 as the
second vcs engine). Make this easy for userspace to discover by
providing the mmio_base in sysfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-2-chris@chris-wilson.co.uk
Preliminary stub to add engines underneath /sys/class/drm/cardN/, so
that we can expose properties on each engine to the sysadmin.
To start with we have basic analogues of the i915_query ioctl so that we
can pretty print engine discovery from the shell, and flesh out the
directory structure. Later we will add writeable sysadmin properties such
as per-engine timeout controls.
An example tree of the engine properties on Braswell:
/sys/class/drm/card0
└── engine
├── bcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── rcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── vcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
└── vecs0
├── capabilities
├── class
├── instance
├── known_capabilities
└── name
v2: Include stringified capabilities
v3: Include all known capabilities for futureproofing.
v4: Combine the two caps loops into one
v5: Hide underneath Kconfig.unstable for wider discussion
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-1-chris@chris-wilson.co.uk
The assert_mmap_offset() returns type bool so if we return an error
pointer that is "return true;" or success. If we have an error, then
we should return false.
Fixes: 3d81d589d6 ("drm/i915: Test exhaustion of the mmap space")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228141413.qfjf4abr323drlo4@kili.mountain
Detect GLK pre-production steppings. Not 100% of A2 being pre-prod
since the spec is a bit of a mess but feels more or less correct.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-4-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
The engine->kernel_context is a special case for request emission. Since
it is used as the barrier within the engine's wakeref, we must acquire the
wakeref before submitting a request to the kernel_context.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-3-chris@chris-wilson.co.uk
Inside the general i915_oa_init_reg_state() we avoid using the
perf->mutex. However, we rely on perf->exclusive_stream being valid to
access at that point, and for that we have to control the race with
disabling perf. This relies on the disabling being a heavy barrier that
inspects all active contexts, after marking the perf->exclusive_stream
as not available. This should ensure that there are no more concurrent
accesses to the perf->exclusive_stream as we destroy it.
Mark up the races around the perf->exclusive_stream so that they stand
out much more. (And hopefully we will be running kcsan to start
validating that the only races we have are carefully controlled.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-2-chris@chris-wilson.co.uk
As a disabled pipe in pipe_mask is not having a valid intel crtc,
driver wrongly populates the possible_crtcs mask while initializing
the plane for a CRTC. Fixing up the plane possible_crtcs mask.
changes since RFC:
- Simplify the possible_crtcs initialization. [Ville]
v2:
- Removed the unnecessary stack garbage possible_crtcs to
drm_universal_plane_init. [Ville]
v3:
- Combine the intel_crtc assignment and declaration. [Ville]
v4:
- Fix possible_crtcs abused bits from
intel_{primary,curosr,sprite}_plane_create(). [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163517.31234-1-anshuman.gupta@intel.com
We need to be extremely careful inside i915_request_await_start() as it
needs to walk the list of requests in the foreign timeline with very
little protection. As we hold our own timeline mutex, we can not nest
inside the signaler's timeline mutex, so all that remains is our RCU
protection. However, to be safe we need to tell the compiler that we may
be traversing the list only under RCU protection, and furthermore we
need to start declaring requests as elements of the timeline from their
construction.
Fixes: 9ddc8ec027 ("drm/i915: Eliminate the trylock for awaiting an earlier request")
Fixes: 6a79d84840 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-11-chris@chris-wilson.co.uk
Check that we can recover if the LRC is totally corrupted. Based on a
very simple theory that anything that can be adjusted via the context
(i.e. on behalf of the user), should be under the purview of the
per-engine-reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-13-chris@chris-wilson.co.uk
