The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the icplus driver has been fixed all PHY drivers supporting
interrupts have both callbacks (config_intr and ack_interrupt)
implemented - as it should be. Therefore phy_drv_supports_irq()
can be changed now to check for both callbacks being implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:
1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
config_intr callback. Now we can add a phylib plausibility check
disabling interrupt mode if one of the two irq-related callbacks
isn't defined.
I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change modified variable advertising from a u32 to a link mode
array and left the u32 zero comparison, so essential we now have an array
being compared to null which is not the intention. Fix this by using the
call to linkmode_empty to check if advertising is all zero.
Detected by CoverityScan, CID#1475424 ("Array compared against 0")
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/phy/marvell.c: In function 'm88e1510_config_init':
drivers/net/phy/marvell.c:850:7: warning:
variable 'pause' set but not used [-Wunused-but-set-variable]
It not used any more after commit 3c1bcc8614 ("net: ethernet: Convert phydev
advertize and supported from u32 to link mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_check_link_status in more places in the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few places in the state machine the state is set to PHY_RUNNING or
PHY_NOLINK after doing a phy_read_status(). So factor this out to
phy_check_link_status().
First use it in phy_start_aneg(): By setting the state to PHY_RUNNING
or PHY_NOLINK directly we can remove the code to handle the case that
we're using interrupts and aneg was finished already.
Definition of phy_link_up and phy_link_down needs to be moved because
they are called in the new function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg isn't finished yet then the PHY reports the link as down.
There's no benefit in setting the state to PHY_AN because the next
state machine run would set the status to PHY_NOLINK anyway (except
in the meantime aneg has been finished and link is up). Therefore
we can set the state to PHY_RUNNING or PHY_NOLINK directly.
In addition change the do_carrier parameter in phy_link_down() to true.
If carrier was marked as up before (what should never be the case because
PHY was in state PHY_HALTED before) then we should mark it as down now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg is enabled and the PHY reports the link as up then definitely
aneg finished successfully. Therefore this check is useless and
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of listing every single PHYID, load the driver for every PHYID
with a Realtek OUI, independent of model number and revision.
This patch also improves two further aspects:
- constify realtek_tbl[]
- the mask should have been 0xffffffff instead of 0x001fffff so far,
by masking out some bits a PHY from another vendor could have been
matched
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_trigger_machine() is used in phy.c only, so we can make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.
On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
The patch is inspired by commit 733336262b ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver got missed during the recent change of .features from a
u32 to a pointer to a Linux bitmap. Change the initialisation from 0
to PHY_10GBIT_FEATURES so removing the danger of a NULL pointer
dereference.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson.
2) Add zero-copy AF_XDP support to i40e, from Björn Töpel.
3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we
can get rid of the {g,s}et_settings ethtool callbacks, from Michal
Kubecek.
4) Add software timestamping to veth driver, from Michael Walle.
5) More work to make packet classifiers and actions lockless, from Vlad
Buslov.
6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov.
7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks.
8) Support batching of XDP buffers in vhost_net, from Jason Wang.
9) Add flow dissector BPF hook, from Petar Penkov.
10) i40e vf --> generic iavf conversion, from Jesse Brandeburg.
11) Add NLA_REJECT netlink attribute policy type, to signal when users
provide attributes in situations which don't make sense. From
Johannes Berg.
12) Switch TCP and fair-queue scheduler over to earliest departure time
model. From Eric Dumazet.
13) Improve guest receive performance by doing rx busy polling in tx
path of vhost networking driver, from Tonghao Zhang.
14) Add per-cgroup local storage to bpf
15) Add reference tracking to BPF, from Joe Stringer. The verifier can
now make sure that references taken to objects are properly released
by the program.
16) Support in-place encryption in TLS, from Vakul Garg.
17) Add new taprio packet scheduler, from Vinicius Costa Gomes.
18) Lots of selftests additions, too numerous to mention one by one here
but all of which are very much appreciated.
19) Support offloading of eBPF programs containing BPF to BPF calls in
nfp driver, frm Quentin Monnet.
20) Move dpaa2_ptp driver out of staging, from Yangbo Lu.
21) Lots of u32 classifier cleanups and simplifications, from Al Viro.
22) Add new strict versions of netlink message parsers, and enable them
for some situations. From David Ahern.
23) Evict neighbour entries on carrier down, also from David Ahern.
24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann
and John Fastabend.
25) Add support for filtering route dumps, from David Ahern.
26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al.
27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido
Schimmel.
28) Add queue and stack map types to eBPF, from Mauricio Vasquez B.
29) Add back byte-queue-limit support to r8169, with all the bug fixes
in other areas of the driver it works now! From Florian Westphal and
Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits)
tcp: add tcp_reset_xmit_timer() helper
qed: Fix static checker warning
Revert "be2net: remove desc field from be_eq_obj"
Revert "net: simplify sock_poll_wait"
net: socionext: Reset tx queue in ndo_stop
net: socionext: Add dummy PHY register read in phy_write()
net: socionext: Stop PHY before resetting netsec
net: stmmac: Set OWN bit for jumbo frames
arm64: dts: stratix10: Support Ethernet Jumbo frame
tls: Add maintainers
net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes
octeontx2-af: Support for setting MAC address
octeontx2-af: Support for changing RSS algorithm
octeontx2-af: NIX Rx flowkey configuration for RSS
octeontx2-af: Install ucast and bcast pkt forwarding rules
octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response
octeontx2-af: NPC MCAM and LDATA extract minimal configuration
octeontx2-af: Enable packet length and csum validation
octeontx2-af: Support for VTAG strip and capture
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
When indicating the MAC supports Symmetric Pause, clear the Asymmetric
Pause bit, which could of been already set is the PHY supports it.
Reported-by: Labbe Corentin <clabbe@baylibre.com>
Fixes: c306ad3618 ("net: ethernet: Add helper for MACs which support pause")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case memory resources for *fw* were successfully allocated,
release them before return.
Addresses-Coverity-ID: 1473968 ("Resource leak")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the error handling for the call to function
phy_read_paged() doesn't work because *reg_val* is of
type u16 (16 bits, unsigned), which makes it impossible
for it to hold a value less than 0.
Fix this by changing the type of variable *reg_val* to int.
Addresses-Coverity-ID: 1473970 ("Unsigned compared against 0")
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 9f2959b6b5 ("net: phy: improve handling delayed work")
the sync parameter isn't needed any longer in phy_start_aneg_priv().
This allows to merge phy_start_aneg() and phy_start_aneg_priv().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify code for handling state PHY_RESUMING, no functional change
intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.
Remove sfp_mutex, it has no purpose.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, the rc variable is either used only for the condition right after
the assignment or right before being used as the return value of the
function it's being used in.
So let's remove this unneeded temporary variable whenever possible.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`if (x != 0)` is basically a more verbose version of `if (x)` so let's
use the latter so it's consistent throughout the whole driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The == operator precedes the || operator, so we can remove the
parenthesis around (a == b) || (c == d).
The condition is rather explicit and short so removing the parenthesis
definitely does not make it harder to read.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient
Ethernet initialization sequence.
In order to avoid certain link state errors that could result in link
drops and packet loss, the physical coding sublayer (PCS) must be
updated with settings related to EEE in order to improve performance.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few counters available in the PHY: receive errors, false
carriers, link disconnects, media CRC errors and valids counters.
So let's expose those in the PHY driver.
Use the priv structure as the next PHY to be supported has a few
additional counters.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.
Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.
In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.
Let's migrate this driver to those functions.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phydev_info() and make use of it within the phy drivers and core
code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.
Convert all pr_warn() calls to phydev_warn() where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:
drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
static int unimac_mdio_suspend(struct device *d)
Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.
Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out that the length of the temporary buffer may not be sufficient for
large numbers of leds:
drivers/net/phy/mscc.c: In function 'vsc85xx_probe':
drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=]
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~
drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
While we can make a reasonable assumption that the number of LEDs is small,
the cost of making the buffer a little bigger is insignificant as well.
Fixes: 11bfdabb7f ("net: phy: mscc: factorize code for LEDs mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.
Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.
Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local variable 'autoneg' doesn't even exist:
drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg':
drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'?
if (phydev->autoneg != autoneg || changed) {
^~~~~~~
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Reported-by:Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BMCR.RESET bit on the Marvell PHYs has a special meaning in that
it commits the register writes into the HW for it to latch and be
configured appropriately. Doing software resets causes link drops, and
this is unnecessary disruption if nothing changed.
Determine from marvell_set_polarity()'s return code whether the register value
was changed and if it was, propagate that to the logic that hits the software
reset bit.
This avoids doing unnecessary soft reset if the PHY is configured in
the same state it was previously, this also eliminates the need for a
m88e1111_config_aneg() function since it now is the same as
marvell_config_aneg().
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When being in state PHY_HALTED we don't have to reschedule the
state machine, phy_start() will start it again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_stop() may be called e.g. when suspending, therefore all needed
actions should be performed synchronously. Therefore add a synchronous
call to the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_POLL is defined as -1 which means that we would be setting all flags of the
PHY driver, this is also not a valid flag to tell PHYLIB about, just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in this driver which prevents it to be compiled for
other architectures. Add COMPILE_TEST so we get better compile test
coverage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver indicates it can do 10/100 full and half duplex, plus 1G
Full. The datasheet indicates 1G half is also supported. So make use
of the standard PHY_GBIT_FEATURES.
It could be, this was added because there is a MAC which does not
support 1G half. Bit this is the wrong place to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY driver should not indicate that Pause is supported. It is upto
the MAC drive enable it, if it supports Pause frames. So remove it
from the ste10Xp driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,led-%d-mode' is
an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,led-%d-mode' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown'
is an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,edge-slowdown' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an
u16, even though it's read as an u16 in the driver.
Let's update the driver to take into consideration that the
'vsc8531,vddmac' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi PHYs support different LED modes depending on the variant, so
let's factorize the code so we just have to give the supported modes
while the logic behind getting the mode remains identical.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LEDs modes are set the same way, except they are offset by 4 times the
index of the LED.
Let's factorize all the code so that it's easier to add support for the
4 LEDs of the VSC8584 PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comment at the
top of the switch statement with a proper "fall through" annotation for
each case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1056542 ("Missing break in switch")
Addresses-Coverity-ID: 1339579 ("Missing break in switch")
Addresses-Coverity-ID: 1369526 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the state numbers, device state, etc from numbers to strings
when printing debug messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.
This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal Combo Ethernet
GPHY to the bcm7xxx phy driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for suspend and resume to the Broadcom iProc mdio
mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to configure the internal rate adjust register based on the
core clock supplied through device tree in the Broadcom iProc mdio mux.
The operating frequency of the mdio mux block is 11MHz. This is derrived
by dividing the clock to the mdio mux with the rate adjust register.
In some SoC's the default values of the rate adjust register do not yield
11MHz. These SoC's are required to specify the clock via the device tree
for proper operation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_mdiobus_alloc() instead of mdiobus_alloc() in the Broadcom
iProc mdio mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the scan control register in the Broadcom iProc
mdio mux driver to disable access to external master.
In some SoC's, the scan control register defaults to an incorrect
value.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1116r_config_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_config_aneg() should be called only by PHYs that implement
the Clause 22 register set. Prevent Clause 45 PHYs that don't implement
the register set from calling the genphy function.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"imply HWMON" was supposed to ensure that the SFP phy code can be built
with HWMON enabled or disabled while at the same time ensuring that
HWMON is not built as module if SFP is built into the kernel.
Unfortunately, that does not work as intended. With "allmodconfig", it
results in several unrelated HWMON drivers to be disabled instead of
being built as module as expected.
Let's use the old "depends on HWMON || HWMON=n" instead. This is slightly
different (it enforces SFP to be built as module if HWMON is built as
module), but it is better than the alternative of using "IS_REACHABLE()"
in the driver since that would disable sensor support if HWMON is built
as module and SFP is built into the kernel.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver builds fine even with CONFIG_OF=n since we now have stubs that are
provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB is an ASIC with five internal PHYs for
LAN0..LAN3 and WAN. The PHYs are spawn off the main
device so they can be handled in a distributed manner
by the Realtek PHY driver. All that is really needed
is the power save feature enablement and letting the
PHY driver core pick up the IRQ from the switch chip.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules can contain a number of sensors. The EEPROM also contains
recommended alarm and critical values for each sensor, and indications
of if these have been exceeded. Export this information via
HWMON. Currently temperature, VCC, bias current, transmit power, and
possibly receiver power is supported.
The sensors in the modules can either return calibrate or uncalibrated
values. Uncalibrated values need to be manipulated, using coefficients
provided in the SFP EEPROM. Uncalibrated receive power values require
floating point maths in order to calibrate them. Performing this in
the kernel is hard. So if the SFP module indicates it uses
uncalibrated values, RX power is not made available.
With this hwmon device, it is possible to view the sensor values using
lm-sensors programs:
in0: +3.29 V (crit min = +2.90 V, min = +3.00 V)
(max = +3.60 V, crit max = +3.70 V)
temp1: +33.0°C (low = -5.0°C, high = +80.0°C)
(crit low = -10.0°C, crit = +85.0°C)
power1: 1000.00 nW (max = 794.00 uW, min = 50.00 uW) ALARM (LCRIT)
(lcrit = 40.00 uW, crit = 1000.00 uW)
curr1: +0.00 A (crit min = +0.00 A, min = +0.00 A) ALARM (LCRIT, MIN)
(max = +0.01 A, crit max = +0.01 A)
The scaling sensors performs on the bias current is not particularly
good. The raw values are more useful:
curr1:
curr1_input: 0.000
curr1_min: 0.002
curr1_max: 0.010
curr1_lcrit: 0.000
curr1_crit: 0.011
curr1_min_alarm: 1.000
curr1_max_alarm: 0.000
curr1_lcrit_alarm: 1.000
curr1_crit_alarm: 0.000
In order to keep the I2C overhead to a minimum, the constant values,
such as limits and calibration coefficients are read once at module
insertion time. Thus only reading *_input and *_alarm properties
requires i2c read operations.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing entry for RTL8211C to mdio_device_id table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: cf87915cb9 ("net: phy: realtek: add support for RTL8211C")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This functionality will also be needed in subsequent patches of this
series, therefore factor it out to a helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m88e1121 LED default configuration does not apply m88e151x.
So add a function to relpace m88e1121 LED configuration.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated
switch/router chips for 5+1 or 8-port switches/routers. When
managed directly by Linux using DSA we need to do a special
set-up "dance" on the PHY. Unfortunately these sequences
switches the PHY to undocumented pages named 2a30 and 52b6
and does undocumented things. It is described by these opaque
sequences also in the reference manual. This is a best
effort to integrate it anyways.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SGMII was selected in the DT then the device should
write the SGMII enable bit.
If SGMII is not selected in the DT then the SGMII bit
should be disabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac9 ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmiitorgmii is using the mii_bus of the device it's attached to,
instead of the bus it was given during probe.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
allocates the values buffer during the callback instead of putting it
on the stack.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When platform_device_register_simple() fails we can return
the error immediately instead of jumping to the 'err_pdev'
label.
This makes the error path a bit simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
The GPIO MDIO driver now needs only <linux/gpio/consumer.h>
so cut the legacy <linux/gpio.h> and <linux/of_gpio.h>
includes that are no longer used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.
The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.
Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.
[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54612E have 4 multi-functional LED pins that can be configured
through register setting; the LED4 pin can be configured to a 125MHz
reference clock output by setting the spare register. Since the dedicated
CLK125 reference clock pin is not brought out on the 48-Pin MLP, the LED4
pin is the only pin to provide such function in this package, and therefore
it is beneficial to just enable the reference clock by default.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of MDIO bus PM ops doesn't actually implement
bus-specific PM ops but just calls PM ops defined on a device level
what doesn't seem to be fully in line with the core PM model.
When looking e.g. at __device_suspend() the PM core looks for PM ops
of a device in a specific order:
1. device PM domain
2. device type
3. device class
4. device bus
I think it has good reason that there's no PM ops on device level.
Now that a device type representation of PHY's as special type of MDIO
devices was added (only user of MDIO bus PM ops), the MDIO bus
PM ops can be removed including member pm of struct mdio_device.
If for some other type of MDIO device PM ops are needed, it should be
modeled as struct device_type as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PHY is a type of MDIO device, so let's model it as struct device_type
and place PM ops, attribute groups and release callback on device type
level. For this the attribute definitions have to be moved.
This change allows us to get rid of the PM ops on a bus level in a second
step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can bail out immediately also in case of PHY_IGNORE_INTERRUPT because
phy_mac_interupt() informs us once the link is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e290051 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the i2c-bus property mandatory when using a device
tree. If the sfp i2c bus isn't described it's impossible to guess the
protocol to use for a given module, and the sfp module would then not
work in most cases.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case no Tx disable pin is available the SFP modules will always be
emitting. This could be an issue when using modules using laser as their
light source as we would have no way to disable it when the fiber is
removed. This patch adds a warning when registering an SFP cage which do
not have its tx_disable pin wired or available.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the Microsemi MII Management controller (MIIM) found on
Microsemi SoCs.
On Ocelot, there are two controllers, one is connected to the internal
PHYs, the other one can communicate with external PHYs.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the DP83811 phy.
The DP83811 supports both rgmii and sgmii interfaces.
There are 2 part numbers for this the DP83TC811R does not
reliably support the SGMII interface but the DP83TC811S will.
There is not a way to differentiate these parts from the
hardware or register set. So this is controlled via the DT
to indicate which phy mode is required. Or the part can be
strapped to a certain interface.
Data sheet can be found here:
http://www.ti.com/product/DP83TC811S-Q1/descriptionhttp://www.ti.com/product/DP83TC811R-Q1/description
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a fixed link with a link GPIO, we need to poll that GPIO to
determine link state changes. This is consistent with what fixed_phy.c does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO provider for the link GPIO line might require the use of the
_cansleep() API, utilize that. This is safe to do since we run in workqueue
context.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Microchip LAN87XX T1 PHYs
This patch support driver for Microchp T1 PHYs.
There will be followup patches to this driver to support T1 PHY
features such as cable diagnostics, signal quality indicator(SQI),
sleep and wakeup (TC10) support.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When computing the bitrate using values read from an SFP module EEPROM,
we use the nominal BR plus BR,min and BR,max to determine the
boundaries. But in some cases BR,min and BR,max aren't provided, which
led the SFP code to end up having the nominal value for both the minimum
and maximum bitrate values. When using a passive cable, the nominal
value should be used as the maximum one, and there is no minimum one
so we should use 0.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an SFP EEPROM values can be read to get information about a given SFP
module. One of those is the bitrate, which can be determined using a
nominal bitrate in addition with min and max values (in %). The SFP code
currently compute both BR,min and BR,max values thanks to this nominal
and min,max values.
This patch fixes the BR,min computation as the min value should be
subtracted to the nominal one, not added.
Fixes: 9962acf7fb ("sfp: add support for 1000Base-PX and 1000Base-BX10")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It adds support for BCM89610 (Single-Port 10/100/1000BASE-T)
transceiver which is used in P3310 Tegra186 platform.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c59530d0d5 ("net: Move PHY statistics code into PHY
library helpers") we made net/core/ethtool.c reference symbols which are
part of the library which can be modular. David introduced a temporary
fix with 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
which would prevent such modularity.
This is not desireable of course, so instead, just inline the functions
into include/linux/phy.h to keep both options available.
Fixes: c59530d0d5 ("net: Move PHY statistics code into PHY library helpers")
Fixes: 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make PHYLIB boolean, because we reference phylib provided symbols now
from net/core/ethtool.c and therefore 'm' doesn't work.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make it possible for network device drivers that do not
necessarily have a phy_device attached, but still report PHY statistics,
have a preliminary refactoring consisting in creating helper functions
that encapsulate the PHY device driver knowledge within PHYLIB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MDIO busses will error out when trying to read a phy address with no
phy present at that address. In that case, probing the bus will fail
because __mdiobus_register() is scanning the bus for all possible phys
addresses.
In case MII_PHYSID1 returns -EIO or -ENODEV, consider there is no phy at
this address and set the phy ID to 0xffffffff which is then properly
handled in get_phy_device().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.
Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.
Add workaround driver just for this special case.
Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
