When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e1838200 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using fixed link we don't need the MDIO bus support.
Reported-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: kernelci.org bot <bot@kernelci.org>
Fixes: d3e014ec7d ("net: stmmac: platform: Fix MDIO init for platforms without PHY")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Acked-by: Sriram Dash <Sriram.dash@samsung.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail> # Lamobo R1 (fixed-link + MDIO sub node for roboswitch).
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
The current implementation of "stmmac_dt_phy" function initializes
the MDIO platform bus data, even in the absence of PHY. This fix
will skip MDIO initialization if there is no PHY present.
Fixes: 7437127 ("net: stmmac: Convert to phylink and remove phylib logic")
Acked-by: Jayati Sahu <jayati.sahu@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.
Fixes: 88ebe2cf7f ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to STMicroelectronics based Multi-Gigabit
Ethernet driver. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TX Coalesce has been rewritten we no longer need this
additional interrupt enabled. This reduces CPU usage.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce logic currently increments the number of packets and sets the
IC bit when the coalesced packets have passed a given limit. This does
not reflect very well what coalesce was meant for as we can have a large
number of packets that are coalesced and then a single one, sent later
on that has the IC bit.
Rework the logic so that it coalesces only upon a limit of packets and
sets the IC bit for large number of packets.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tune-up the defalt coalesce settings for optimal values. This gives the
best performance in most of the use-cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For performance reasons, sometimes using the minimum RX Coalesce value
is not optimal. Lets setup a default value that is optimal in most of
the use cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may only want to use the RX Watchdog so lets check if RX Coalesce
settings are non-zero and only set the RX Interrupt on Completion bit if
its not.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a return statement that is indented too deeply, remove
the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the UDP Segmentation Offload feature in stmmac. This is only
available in GMAC4+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks over-engineered. Let's use some helpers to get the buffer
length and hereby simplify the stmmac_rx() function. No performance drop
was seen with the new implementation.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.
v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VID is converted to le16 so the variable must be __le16 type.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
