This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.
LCD power sequence is added by 'Michael Trimarchi'.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The aspeed pwm driver always sets the clock source to 24MHz, specify
the fixed clock in device tree to make sure the driver is using the
correct clock frequency to calculate the fan speed.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.
This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]
https://octavosystems.com/octavo_products/osd3358-sm-red/
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like I made a nasty typo in the original patch which resulted
in missing watchdog device. Fix it.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pwm node should not be under gpio6 node in the device tree.
This fixes detection of the pwm on Droid 4.
Fixes: 6d7bdd328d ("ARM: dts: omap4-droid4: update touchscreen")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This display configuration isn't working as-is as it depends on the
tfp410 LCD to HDMI bridge. This will need to be updated later once
the DRM MXSFB driver will be the default.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6sl soc has gpu_2d and gpu_vg, no 3d support:
etnaviv-gpu 2200000.gpu: model: GC320, revision: 5007
etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
The IP blocks seem to be already supported.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-rdu1 has an external watchdog in the environment
microcontroller, so disable the internal one.
This aligns with what was done in commit 7055f71403 ("ARM: dts:
imx6: RDU2: disable internal watchdog") for imx6 rdu2 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Normally, we didn't release this kind of baord to user. This specific
board exists only in the early stage of development inside MediaTek -
and that may confuse peoples.
Hence this patch removes related files accordingly.
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved memory for the VGA frame buffer is at the wrong address
for this system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is an eval board, it makes sense to enable many
functions by default. This changes the device-tree to
set port A to be a USB device and leave port B as a
host, along with a little comment explaining how to
change it.
(the vhub device can only exist on port A on this SoC)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
This also adds the missing pinmux definition for it
(the kernel driver already knows about it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCIs so boards don't have to do
it an document why it is not set for UHCI.
Remove the properties from the AST2500 EVB board which are
now redundant
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCI so boards don't have to do
it, and document why it is not set for UHCI.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pio-leds (near GPIO-Header) are swapped and LOW-active.
This patch restores the expected behaviour.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add Vitesse switch chips
- Add a new DT for a reference design
-----BEGIN PGP SIGNATURE-----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=3RrW
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.19:
- Add Vitesse switch chips
- Add a new DT for a reference design
* tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add devicetree for Storlink/Storm SL93512R
ARM: dts: Add Vitesse G5e switch to the Gemini SQ201
ARM: dts: Add WAN ethernet port to the SQ201
Signed-off-by: Olof Johansson <olof@lixom.net>
The Storlink Gemini324 EV-Board also known as Storm
Semiconductor SL93512R_BRD is ground zero for the Gemini
devices. We add a device tree so we can support it, it
turns out to be pretty trivial.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Vitesse G5e ethernet switch to the Square
One Itian SQ201 router device tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This sets up the ethernet interface and PHY for the
WAN ethernet port which uses a Marvell PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
-----BEGIN PGP SIGNATURE-----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=Wci4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0eB8QAKCRALBhiOFHI7
1a0PAKCRyt0vXcjr9HHBzhagibfgT4XrXgCfXG43C32Qjg5U1Ga39IIY3fcFMrY=
=2Pjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.18 (part 1)
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
* tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: use the new thermal binding
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCisQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfrxCACbf7LkN/oH1MekD7CTaGHwlyvyneVWT/Dl
wM0YdKJ4fpZ6FMWxGV4F32qdkSEyPxCVTe1mnueOVnDgZX/ywPGC/hpbofPbmZuq
Z2/YFfCNzsBcijlhwI5bZrzChl/AKKOZNqGBxpKz+lXe/6dIl8bTG8Fmi3tvA+oy
hhvy0Sl6JeNqI5NghEukrQOuEYPHdniElTBYP8DP0J8yypbuIVFOzqpRtoOKeSCP
669aN5G5tCRYoJlx0pC2FyqTI0bdCPtPLPZx9eQwMqyFGN4EUx7NGB3w4gH4GubT
vfG4K4cK3CSWr7+LfwqkA2cX2gzPpGpUyaCpROHkGxtxqcMFdIrV
=ZfMG
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Fix for a new warning from dtc in graph node unit addresses.
* tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix graph node unit address error from dtc
Signed-off-by: Olof Johansson <olof@lixom.net>
After the work done by Thomas Petazzoni, the NAND chip timings
can be read out from the chip instead of open coded in the
device tree, so let's just remove the timing information.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbSK1NAAoJEH+ayWryHnCFMesP/2OFNwl1ZHpU5aoRfqIP4Xy8
ATKQh56FVLbtEaqBffze2pc8F1y9Id6H7UpFSsZ+IujeviIQ2sjh/hMeFq3arxeE
w66yS6YJjyZaBIWsGyit50xiAelNEbDmmdL3RhIa4T9nyYuOQ9c38S7GTxeO3hLv
6FIXffb8v76qaypKqqCdGImO/7V4L7nNPiGzCxyHhVFv7z76/kBgkjPn4BeoeW0N
yzDYW/WDBL+XDMaxwB7NmK3RlMbYLxEPpbWmqddibU/azaRXNNkgtC5+75Cbfrd4
BOAAGfiBKhRLYnQ6tdOhl/Ru+NR7Nig3Nxp92c9M53prDHfZw1+vX5s64wrvI2nR
0zKZiLpHNxXquhdqQ9a4GszF9KAtHM+cym9nXeYsfbBroOrv9N/E8ndz1EiyHErd
3anZsn0ILrcYtBnzdmRWBWfJDYVefJHwB8a1nq6UK8zGwBnKZtfOx4iBSztrcsS9
JcbN5yYdYVfQTjkKCpHGMhQwMdlh8h0yjGds2D2ySfoOSweYlNrfdRYGx03N8p3z
4RPLuGVYQ/shcPUaapwm9Ity1KmxTcDIEA6WgRI6VNypwdQbslMEfpZqdNTduHjO
JzPJEO67yPzimGQ7u5ZGTlJtdUxTDHpXGX2q67QqwzM/jbVpqSsArcr1LgDifI4g
P6pT4uu87oPlbVwBIHUE
=Tc+I
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.19, round 1
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
* tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: update iwdg with lsi clock name for stm32f429
ARM: dts: stm32: add iwdg2 support for stm32mp157c-ed1
ARM: dts: stm32: add iwdg2 support for stm32mp157c
ARM: dts: stm32: Reorder nodes in stm32mp157c-ed1
ARM: dts: stm32: remove gpio aliases for stm32mp157c
ARM: dts: stm32: add support of ethernet on stm32mp157c-ev1
ARM: dts: stm32: Add ethernet dwmac on stm32mp1
ARM: dts: stm32: Add syscfg on stm32mp1
ARM: dts: stm32: add SPI1 support on stm32mp157c-ev1
ARM: dts: stm32: add SPI support on stm32mp157c
ARM: dts: stm32: Add DFSDM support to stm32mp157c
ARM: dts: stm32: Add ADC support to stm32mp157c
ARM: dts: stm32: enable USB OTG HS on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG HS support for stm32mp157c SoC
ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp157c-ev1
ARM: dts: stm32: enable RTC on stm32mp157c-ed1
ARM: dts: stm32: add RTC support to stm32mp157c
ARM: dts: stm32: m_can activation on stm32mp157c-ev1
ARM: dts: stm32: m_can support to stm32mp157c
ARM: dts: stm32: Add HASH support on stm32mp157c
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0hvzAAKCRALBhiOFHI7
1eiZAJ4khxwKduQLyzz0nqyaX7jefrb7ywCfY8WXMc0ay/qwZytGcUUqpWMeY3Y=
=OVdR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.19 (part 1)
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
* tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: drop future changes disclaimer
ARM: dts: armada388-clearfog: enable spi flash
ARM: dts: armada388-helios4
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
-----BEGIN PGP SIGNATURE-----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=afvE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.19
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
* tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document bindings for SGH-T959P board
dt-bindings: samsung: Document bindings for Samsung aries boards
ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone
ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone
ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones
ARM: dts: s5pv210: Add missing interrupt-controller property to gph2
ARM: dts: exynos: remove no longer needed samsung thermal properties
dt-bindings: arm: Remove obsolete insignal-boards.txt
ARM: dts: exynos: Add missing CPU clocks to secondary CPUs on Exynos542x
arm: dts: exynos: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
-----BEGIN PGP SIGNATURE-----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=+IHO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.19-rc1
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
* tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra: enable NAND flash on Colibri T20
ARM: dts: tegra: add Tegra20 NAND flash controller node
ARM: tegra: Work safely with 256 MB Colibri-T20 modules
ARM: tegra: Fix unit_address_vs_reg and avoid_unnecessary_addr_size DTC warnings
ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory
ARM: tegra: Remove usage of deprecated skeleton.dtsi
ARM: tegra: Fix can2 on Tegra30 Apalis
ARM: tegra: Fix Tegra30 Cardhu PCA954x reset
ARM: dts: tegra30: Add Memory Client reset to VDE
ARM: dts: tegra20: Add Memory Client reset to VDE
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
-----BEGIN PGP SIGNATURE-----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=v277
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for mcan for omaps for v4.19 merge window
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
* tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: Add MCAN node
ARM: dts: Add generic interconnect target module node for MCAN
ARM: dts: dra762: Add MCAN clock support
bus: ti-sysc: Add support for software reset
bus: ti-sysc: Add support for using ti-sysc for MCAN on dra76x
clk: ti: dra7: Add clkctrl clock data for the mcan clocks
bus: ti-sysc: Use 2-factor allocator arguments
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
-----BEGIN PGP SIGNATURE-----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=kbfH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for omaps for v4.19 merge window
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
* tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: pandaboard: add gpio user button
ARM: dts: am3517-evm: Add 'vdd_io_reg' regulator references
ARM: dts: am3517-evm: Enable USB1 Host
ARM: dts: am33xx: Fix syntax of alias names
ARM: dts: am3517-som: Add builtin Bluetooth
ARM: dts: am3517-som: Add WL127x Wifi
ARM: dts: am335x-sl50: enable tsadc on SL50 board
ARM: dts: am335x-sl50: fix label names for all LEDs
ARM: dts: am335x-sl50: use audio-graph-card for sound
ARM: dts: am335x-sl50: add support for DS1339 Real Time Clock
ARM: dts: am335x-sl50: set dr_mode to otg
ARM: dts: am335x-sl50: add a node for the LCD controller
ARM: dts: am335x-sl50: use phy-phandle declarations
ARM: dts: am335x-sl50: update backlight nodes
ARM: dts: omap4-droid4: Use software debounce for gpio-keys
ARM: dts: Configure duovero for to allow core retention during idle
ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt
ARM: dts: dra76-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra71-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra7-evm: Add extcon to USB2 port
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6E7c
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci Device-Tree updates for v4.19
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
* tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Add power-domains to CPPI 4.1 node
ARM: davinci: dts: add a reset control to the dsp node
ARM: davinci: dts: make psc0 a reset provider
ARM: dts: da850-lego-ev3: Add Bluetooth nodes
ARM: dts: da850: Add power-domains to PWM nodes
ARM: dts: da850: Add clocks
dt-bindings: timer: new bindings for TI DaVinci timer
ARM: dts: da850-evm: Enable LCD and backlight
ARM: dts: da850-evm: Enable SATA port
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
-----BEGIN PGP SIGNATURE-----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=lRBW
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
* tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Add support for Linksys EA9500
ARM: dts: BCM53573: Add architected timer
ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driver
ARM: dts: cygnus: enable iproc-hwrng
ARM: dts: cygnus: add ethernet0 alias
ARM: dts: bcm283x: Add Transposer block
ARM: dts: bcm283x: Add the PMU to the devicetree.
ARM: dts: add Raspberry Pi Compute Module and IO board
Signed-off-by: Olof Johansson <olof@lixom.net>
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCwUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVk2CACbnXTVeS+u/fwgDHA1imCfAjQEGt25yFmV
Yv9GYkFLwvE0dg54Law3u1yYosXuO64Eu3fLZSrOYpI9CadWgMCq+H0rdg3f2Z2Y
mbdW7Ey26U7zGvZkQaEKS7OrUmf5ZQ6TEO70+miQ8Az2G4iEs5fDVRwRN3mJPzV8
Sf5c/dZSQUDD1brKvpTAWpZ4zo4Gx44yBu9DOF6ro9v7h9NNg6Oi6Uuc748Kd8+0
GZLXotcuxPRo2nPpwZYEVgdxHCVkfXezngC0/jc58aYJWbSnqyibrg228siVBDZe
e3p5LyRsn+ALdL5ol1CwRzhShlDIj1GIwZ+jAR87U0hHBT0R6Wdh
=de2o
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
SPDX conversion for existing Rockchip devicetree files as well
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
* tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk3288
ARM: dts: rockchip: convert rk3288 to operating-points-v2
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk322x
ARM: dts: rockchip: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
MAC is connected to a PHY in RGMII mode.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add Ethernet support (Synopsys MAC IP 4.20a) on stm32mp1 SOC.
Enable feature supported by the stmmac driver, such as TSO.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
System configuration controller is mainly used to manage
the compensation cell and other IOs and system related
settings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SPI1 support on stm32mp157c-ev1 board.
SPI1 is available on GPIO expansion connector but kept disabled
so these pins can be used as GPIOs by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c has an ADC block with two physical ADCs.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS on STM32MP157C SoC.
USB OTG HS controller is based on DWC2 controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL1 GPIO is set to output 0
or 1.1V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a label for the PMU node so that the board dts may be able to
pass the 'secure-reg-access' property like this:
&pmu {
secure-reg-access;
};
This also makes it consistent with the PMU node in imx6qdl.dtsi
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX53 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual the M4IF register region
starts at 0x83fd8000 and has a 4kB address range.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sergey Lapin <sergey.lapin@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With old bindings imx_gpc_onecell_data always sets num_domains to 2 so
the DISPMIX domain can't actually be referenced. The pd is still defined
and pm core shuts it down as "unused" so display can't work.
Fix this by converting to new gpc bindings by adding pgc nodes and
referencing the newly-defined &pu_disp domain from &lcdif.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, enable it as another mmio sram.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100/200MHz states for USDHC3 are not required since the SoC
does not support modes faster than DDR52 for the on board eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VDDD is connected to VGEN4 of the PF0100. This rail should only
run at 1.8V since there are multiple consumer and they all
expect the rail to be at 1.8V.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fixed 1.8V regulator is not used, and there is in fact no
fixed 1.8V regulator on the module. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the disable-wp to indicate that Apalis and Colibri iMX6 do not
make use of the native write-protect signal available on the i.MX 6
SoCs. This prevents warnings:
mmc0: host does not support reading read-only switch, assuming write-enable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use no-1-8-v device tree property to indicate that the board does
not support 1.8V signaling. The property voltage-ranges seems not
appropriate in our case since we do not have level shifters in
place.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 3.3V main supply on the carrier board. Currently as a fixed
supply since not all consumer are modeled yet. This gets also rid of
some missing supply warnings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 654f2b937b ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a SRAM controller node for the H3, with support for the C1
SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the compatible and commit prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a SRAM controller node for the A23 and A33, with support for
the C1 SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the prefix and the compatibles]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A20 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for sun5i-based platforms. The region is shared
between the Video Engine and the CPU.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size to take the C2 and C3 SRAM into account]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun7i-a20 dtsi to use the most qualified compatibles
for the system-control block (previously named SRAM controller) as well
as the SRAM blocks. The sun4i-a10 compatibles are kept since these
hardware blocks are backward-compatible.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun5i dtsi to use the most qualified compatibles for
the system-control block (previously named SRAM controller) as well as
the SRAM blocks.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Removed the A10 compatible for the driver]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun4i-a10 dtsi to use the new compatible for the
system-control block (previously named SRAM controller) instead of
the deprecated one.
The node name is also updated to reflect the fact that the controller
described is really about system control rather than SRAM control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Amended the commit message]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 has 4 TCONs, but only 2 of them can receive some kind of output at
the same time. Let's disable them by default, so only those which are
really connected on board can be enabled in board dts file.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Current R40 is missing some graph connections between TCON TOP and
TCONs.
Add them.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T and R40 TCON TV are very similar. However, R40 TCON TV is wired
differently, which makes it incompatible with A83T TCON TV.
Because of that, remove fallback A83T TCON TV compatible.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
sun4i-drm DT binding, second paragraph of the first section says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index.
Add mixer ids in R40 DT as mandated by DT binding.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for the MCAN peripheral which supports both classic
CAN messages along with the new CAN-FD message.
Add MCAN node to evm and enable it with a maximum datarate of 5 mbps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti-sysc driver provides support for manipulating the idle modes
and interconnect level resets.
Add the generic interconnect target module node for MCAN to support
the same.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MCAN is clocked by H14 divider of DPLL_GMAC. Unlike other
DPLL dividers this DPLL_GMAC H14 divider is controlled by
control module. Adding support for these clocks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the power-domains property to CPPI 4.1 node.
The CPPI 4.1 DMA driver uses pm_runtime to manage the clocks,
so it needs this property in order to find and enable the clock
properly.
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables the on-module ONFI conformant NAND flash.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic controller device tree node to be extended by
individual boards. Use the assigned-clocks mechanism to set
NDFLASH clock to a sensible default rate of 150MHz.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Colibri-T20 can come in 256 MB RAM (with 512 MB NAND) or 512 MB RAM
(with 1024 MB NAND) flavors. Both of them will use the same DTSI
expecting the bootloader to do the fixup of /memory node. However in
case it does not happen, let's stay on safe side by limiting the memory
to 256 MB for both versions of Colibri-T20.
Rename to remove the unnecessary memory size from the device tree file
name. While at it, also follow the typical Toradex SoC, module, carrier
board hierarchy.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove unneeded address/size cells properties and unit addresses to fix
DTC warnings like:
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (unit_address_vs_reg):
/i2c@7000d000/stmpe811@41/stmpe_touchscreen@0: node has a unit name, but no reg property
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (avoid_unnecessary_addr_size):
/i2c@7000d000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the usage of skeleton.dtsi because it was deprecated since commit
9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated").
It also allows later to fix DTC warnings for missing unit name in
/memory nodes.
Compiled DTBs are the same as before this commit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This pull request brings in a board DT for the Raspberry Pi Compute
Module and its I/O board, the Pi3's PMU node, and the display's
transposer block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's a standard ARM architected timer that was simply missed when
initially adding this .dtsi file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which
requires register range "ccb-mii" <0x18003000 0x1000>. This range
overlaps with MDIO cmd and param registers (<0x18003000 0x8>).
Essentially, the platform driver partly acts like a MDIO bus driver,
hence to use of this register range.
In some Northstar devices like Linksys EA9500, secondary switch is
connected via external MDIO. The only way to access and configure the
external switch is via MDIO bus. When we enable the MDIO bus in it's
current state, the MDIO bus and any child buses fail to register because
of the register range overlap.
On Northstar, the USB 3.0 PHY is connected at address 0x10 on the
internal MDIO bus. This change moves the usb3_phy node and makes it a
child node of internal MDIO bus.
Thanks to Rafał Miłecki's commit af850e14a7 ("phy: bcm-ns-usb3: add
MDIO driver using proper bus layer") the same USB 3.0 platform driver
can now act as USB 3.0 PHY MDIO driver.
Tested on Linksys Panamera (EA9500)
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The transposer block is allowing one to write the result of the VC4
composition back to memory instead of displaying it on a screen.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This only probes on arm64 so far, but hopefully that driver will be
generalized soon.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
CAN2 currently fails on probe as follows:
mcp251x spi1.1: Probe failed, err=19
Fix this by enabling input on pin mux of resp. SPI4 pins.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.
Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.
Fixes: 40431d16ff ("ARM: tegra: enable PCA9546 on Cardhu")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PandaBoard has a user button connected to GPIO. On the ES this is connected
to GPIO 113, on all the other Panda editons this is GPIO 121.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are a few peripherals that generate some extra noise when they
don't have a regulator assigned to them. This patch assigns them to
their actual tps65023 regulator 'vdd_io_reg' (VDCDC2).
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g. It belongs to Samsung
Aries devices family.
Initial version have support for:
- sdcard
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Galaxy S phone, also known as
i9000. It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- internal memory
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Adds missing interrupt-controller property to gph2 block,
to silence following warnings during build:
/soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
It's reguired by Samsung Aries boards, an S5PV210 based
Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
-----BEGIN PGP SIGNATURE-----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=H1MU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap for v4.18-rc cycle
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
* tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Signed-off-by: Olof Johansson <olof@lixom.net>
The enabling of the EMAC was reverted as there was an issue on how
to handle the integrated PHY and it was getting close to the release
window (fe45174b72 ("arm: dts: sunxi: Revert EMAC changes")).
When a solution was found, then the changes were restored in
4b236a0fe5 ("arm: dts: sunxi: h3/h5: Restore EMAC changes") and
4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)").
Unfortunately enabling for the Beelink X2 was missed.
This reverts partially commit 6b0e06df5c (Revert "ARM: dts:
sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO3x0AAoJEFBXWFqHsHzODGkIAIIJFPOWBYHyxAVLAtqpNTt7
+Yggu9LGe7rhspT+Hi2DocKIEj1Z11x49KJCqxwrEHg+7xyax6d78b1iclCHLRlr
S9jxulipzkBs/neebrhh6cyF8sxA7TPUgXtEMdRJwYygUoZhe9hngTO3jv+xoDky
l1l9zH9gAlAQA1cxN6Z4ZWYDkNS0mYK3e1VzaeyCXsq5GJ1Vm5Qw1ooTE5DL3K1g
5B2Hw057DJvcSwOhIVir/MQR8sAWj1sKYdsCouxrO/ThEyofEAtfn22romcPaGPW
WBOuTNrOrMy6O/+ndMBNJBXeGt1tONL2cjLbrpffaXJYq6m/56efsee9u1u18Vg=
=4Agh
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 2:
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
* tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch removed OMAP clock aliases that were perceived
to be unnecessary. Unfortunately, it broke the ethernet on the
am3517-evm. This patch enables the MDIO clock and EMAC clock.
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Cc: stable@vger.kernel.org #4.16+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-evm has a single USB Host port connected to hsusb1.
This patch enables that USB port.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT specifications do not allow the underscore character in alias names.
Replace all underscores in alias names by dashes.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the Bluetooth on the wl1271 available in some models
of the AM3517-SOM from Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Certain models of the AM3517 SOM from Logic PD come with an
integrated WL1271 WiFi. This patch enables the WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tsadc is used to read various voltages on the board, so enable it
to be able to read these voltages from userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the label for all LEDs, we made a mistake setting the label names on
all LEDs, where says green should say red, and viceversa, where says red
should be green.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
audio-graph-card is recommended for audio bindings. Let's change to it and
improve the support by adding the Amplifier configuration and the clock
enable control.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Production hardware will go with the DS1339 RTC chip, so replace the old
for the new one and also add the nIRQ pin to be able to properly wakeup
the system from suspend.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board can be either a host, or a peripheral, so set the controller as
OTG mode to reflect this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the pins used by the LCD controller, the panel-info and display-timings
information for the MIDAS displays connected to the board. There are
two displays in the board, and these, are connected to the LCD controller
through a FPGA, so the timings and the resolution is what expects the FPGA,
not the MIDAS displays.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device. The new
method also allows you to specify a reset gpio which is required for
this board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the backlight nodes to improve the support and describe
better how hardware is done. The changes done were:
* Use PWM_POLARITY_INVERTED instead of the hardcoded number.
* Add pinctrl configuration.
* Add the enable gpio definition.
* Add the power supply definition.
* Add more brightness levels.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default value of 5ms will use GPIO hardware based debounce clocks
that will keep L4PER from idling consuming about extra 30mW.
Use a value of 10ms that is above the hardware debounce maximum of
7.95ms forcing software based debouncing.
This allows droid4 to enter PER retention during idle as long as UARTs
are idled and USB modules unloaded or unbound.
Note that there seems to be a pending issue with having droid 4 enter core
retention during idle where GPIO bank 1 needs to be reset late after init
for some reason to not block core retention. In addition to that, we are
also missing GPIO related PM runtime calls for omap4 that will be posted
separately.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By reconfiguring few GPIOs in the dts file we can make duovero parlor
hit retention during idle:
1. Let's a larger debounce value for gpio-keys
This will then make gpio-keys use software debounce and the GPIO
debounce clock is not enabled.
2. Let's allow WLAN suspend for mwifiex
This can be done just by adding keep-power-in-suspend.
3. Let's reconfigure smsc911x driver to use GPIO edge interrupt
This will allow using NFSroot while the system idles, and the kernel
has quite a few dts files with "smsc,lan9115" compatible using edge
interrupts.
Then to have the system hit core retention during idle, the UARTs
needs to be idled and USB modules need to be unloaded or unbound.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both ports on the dra7-evm and related boards can be used
as dual-role ports. Although we don't enable dual-role mode
for USB2 port let's add the necessary extcon bits to it.
Move the common portion of extcon_usb2 into dra7-evm-common.dtsi
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to i.MX6 datasheet, the LDO_1P1's typical
programming operating range is 1.0V to 1.2V, and
the LDO_2P5's typical programming operating range
is 2.25V to 2.75V, correct LDO_1P1 and LDO_2P5's
regulator range settings for i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per Documentation/process/license-rules.rst the SPDX notation for
header file should be /* */ style, so fix it accordingly.
Fixes: 9f30b6b1a9 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AM3517-EVM uses a TPS65023 PMIC. This is already defined
by: compatible = "ti,tps65023"
There doesn't seem to be a need to have each regulator in the
PMIC with the 'compatible = "regulator-fixed"' since each
regulator has a min and max setting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit 0aa9abd4c2 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mainline Commit b74c2b21e1 added the pinmux
settings for mmc1, however this pin (0x9a0) is routed to P9_42 on the cape
header. Thus any BeagleBone cape that utilizes P9_42 triggers mmc0's Write
Protect.
Fixes: b74c2b21e1 ("ARM: dts: am33xx: Add pinmux data for mmc1 in
am335x-evm, evmsk and beaglebone")
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Faiz Abbas <faiz_abbas@ti.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This was fixed in
645a397, so correct the RDU1 DT to apply the inversion to the
correct axis.
Tested on Zii RDU1 00-5105-30 rev B
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pinctrl_usbh1reg defines pinmux setting for reset GPIO used by
usbh1phy, but is not referenced by that node. Fix that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing property (clock latency) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The davinci-rproc driver will soon use the reset framework. Add the
resets property to the dsp node in da850.dtsi.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The psc driver registers with the reset framework as a provider. Add
the #reset-cells property to the psc0 node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Disable the metastability workaround for USB2. The original
patch disabled the workaround on the wrong USB port.
Fixes: b8c9c6fa20 ("ARM: dts: dra7: Disable USB metastability workaround for USB2")
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinctrl settings were incorrect for the touchscreen interrupt line, causing
an interrupt storm. This change has been tested with both the atmel_mxt_ts and
RMI4 drivers on the RDU1 units.
The value 0x4 comes from the value of register IOMUXC_SW_PAD_CTL_PAD_CSI1_D8
from the old vendor kernel.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Cc: <stable@vger.kernel.org> # 4.15+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:
[ 82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[ 82.697071] pgd = (ptrval)
[ 82.699920] [b6ff10c4] *pgd=a87c5831, *pte=73fa8383, *ppte=73fa8a33
Bus error
Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:
imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");
After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was removed in commit 5eaeaccdae ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.
Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use sdhci-omap programming model based on the generic sdhci
library for programming the MMC/SD controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add "vqmmc-supply" property for mmc0/mmc1 to indicate the supply connected
to the IO lines. Also add dt node for ldo1 regulator required for mmc1
vqmmc-supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
