It is easier to follow the logic by removing the not operator
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Joe Perches, replacing the "if phydev" logic permit to
reduce indentation in the for loop.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10/100 case have too many ifcase.
This patch split it for removing an if.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mutualise a bit by running stmmac_hw_fix_mac_speed() after
the switch in case of valid speed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of invalid speed given, stmmac_adjust_link() still record it as
current speed.
This patch modify the default case to set speed as SPEED_UNKNOWN if not
10/100/1000.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is better to use DUPLEX_UNKNOWN instead of just "-1".
Using 0 for an invalid speed is bad since 0 is a valid value for speed.
So this patch replace 0 by SPEED_UNKNOWN.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_adjust_link() function is called too rarely for having
likely() macros being useful.
Just remove likely annotation in it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove some useless parenthesis.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_msix has been long deprecated, but this driver adds a new
instance. Convert it to pci_alloc_irq_vectors so that no new instance
of the deprecated function reaches mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed*: Add support for PTP
This patch series adds required changes for qed/qede drivers for
supporting the IEEE Precision Time Protocol (PTP).
Changes from previous versions:
v7: Fixed Kbuild robot warnings.
v6: Corrected broken loop iteration in previous version.
Reduced approximation error of adjfreq.
v5: Removed two divisions from the adjust-frequency loop.
Resulting logic would use 8 divisions [instead of 24].
v4: Remove the loop iteration for value '0' in the qed_ptp_hw_adjfreq()
implementation.
v3: Use div_s64 for 64-bit divisions as do_div gives error for signed
types.
Incorporated review comments from Richard Cochran.
- Clear timestamp resgisters as soon as timestamp is read.
- Use shift operation in the place of 'divide by 16'.
v2: Use do_div for 64-bit divisions.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for,
- Registering the ptp clock functionality with the OS.
- Timestamping the Rx/Tx PTP packets.
- Ethtool callbacks related to PTP.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91572088e3 ("net: use core MTU range checking in core net
infra") changed the openvswitch internal device to use the core net
infra for controlling the MTU range, but failed to actually set the
max_mtu as described in the commit message, which now defaults to
ETH_DATA_LEN.
This patch fixes this by setting max_mtu to ETH_MAX_MTU after
ether_setup() call.
Fixes: 91572088e3 ("net: use core MTU range checking in core net infra")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes broken build for !NET_CLS:
net/built-in.o: In function `fq_codel_destroy':
/home/sab/linux/net-next/net/sched/sch_fq_codel.c:468: undefined reference to `tcf_destroy_chain'
Fixes: cf1facda2f ("sched: move tcf_proto_destroy and tcf_destroy_chain helpers into cls_api")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to force a rebuild of bpf.o when one of its dependencies
(e.g. uapi/linux/bpf.h) is updated.
Add a phony target.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless ifdef __NR_bpf as requested by Wang Nan.
Inline one-line static functions as it was in the bpf_sys.h file.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/r/828ab1ff-4dcf-53ff-c97b-074adb895006@huawei.com
Acked-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a reader-writer lock in fast path is silly, when we can
instead use RCU or a seqlock.
For mlx4 hwstamp clock, a seqlock is the way to go, removing
two atomic operations and false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_get_stats() just returns dev->stats so we can leave it out
altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
hip04_get_stats() just returns dev->stats so we can leave it
out altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/sched/act_api.c:532:5: warning:
symbol 'nla_memdup_cookie' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove the unused timer. I suppose it was intended as a timeout
detector, but never properly implemented.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warnings:
kernel/bpf/verifier.c: In function ‘may_access_direct_pkt_data’:
kernel/bpf/verifier.c:702:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (t == BPF_WRITE)
^
kernel/bpf/verifier.c:704:2: note: here
case BPF_PROG_TYPE_SCHED_CLS:
^~~~
kernel/bpf/verifier.c: In function ‘reg_set_min_max_inv’:
kernel/bpf/verifier.c:2057:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
true_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2058:2: note: here
case BPF_JSGT:
^~~~
kernel/bpf/verifier.c:2068:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
true_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2069:2: note: here
case BPF_JSGE:
^~~~
kernel/bpf/verifier.c: In function ‘reg_set_min_max’:
kernel/bpf/verifier.c:2009:24: warning: this statement may fall through [-Wimplicit-fallthrough=]
false_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2010:2: note: here
case BPF_JSGT:
^~~~
kernel/bpf/verifier.c:2019:24: warning: this statement may fall through [-Wimplicit-fallthrough=]
false_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2020:2: note: here
case BPF_JSGE:
^~~~
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the port autoselection is enabled by default on AM79C970A,
BNC/AUI port does not work because the link is always reported to be
down. The link state reported by the chip belongs only to the TP port
but the driver uses it regardless of the port used. The chip can't
detect BNC/AUI link state.
Disable port autoselection and use TP port by default to keep current
behavior (link detection works on TP port, BNC/AUI port does not work).
Implement ethtool autoneg, port and duplex configuration to allow
using the BNC/AUI port.
Report the TP link state only if the TP port is selected. When the
port autoselection is enabled or AUI port is selected, report the link
as always up.
Move pcnet32_suspend() and pcnet32_clr_suspend() functions to avoid
forward declarations.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code to clear SUSPEND flag to a separate function to simplify
code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Point back the unregister IPv6 mc table to the bc table.
It is done since IPv6 mcast snooping is not supported for Spectrum yet.
Reported-by: Jiri Pirko <jiri@mellanox.com>
Fixes: 71c365bdc4 ("mlxsw: spectrum: Separate bc and mc floods")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
sunvnet driver updates
The sunvnet ldom virtual network driver was due for some updates and
a bugfix or two. These patches address a few items left over from
last year's make-over.
v2:
- changed memory barrier fix to use smp_wmb
- put NETIF_F_SG back into the advertised ldmvsw hw_features
v3:
- the sunvnet_common module doesn't need module_init or _exit
v4:
- dropped the statistics patch
- fixed up "default" tag for SUNVNET_COMMON
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ldmvsw driver is specifically for supporting the ldom virtual
networking by running in the primary ldom and using the LDC to connect
the remaining ldoms to the outside world via a bridge. With TSO and GSO
supported while connected the bridge, things tend to misbehave as seen
in our case by delayed packets, enough to begin triggering retransmits
and affecting overall throughput. By turning off advertised support for
TSO and GSO we restore stable traffic flow through the bridge.
Orabug: 23293104
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version and simplify the print code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCU read lock is grabbed first thing in sunvnet_start_xmit_common()
so it always needs to be released. This removes the conditional release
in the dropped packet error path and removes a couple of superfluous
calls in the middle of the code.
Reported-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of gotos for handling the incoming events made this code
harder to read and support than it should be. This patch straightens
out and clears up the logic.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow the underlying LDC and outstanding memory operations
to potentially catch up with the driver's Tx requests, add a memory
barrier before checking again for available tx descriptors.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been several changes since the first version of this code, so
we bump the version number. While we're at it, we can simplify the
version printing a bit and drop a couple lines of code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vio_dring_state *dr variable is unused in maybe_tx_wakeup().
As the comments indicate, we call maybe_tx_wakeup() whenever we
get a STOPPED LDC message on the port. If the queue is stopped,
we want to wake it up so that we will send another START message
at the next TX and trigger the consumer to drain the dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the sunvnet_common code was split out for use by both sunvnet
and the newer ldmvsw, it was made into a static kernel library, which
limits the usefulness of sunvnet and ldmvsw as loadables, since most
of the real work is being done in the shared code. Also, this is
simply dead code in kernels that aren't running the LDoms.
This patch makes the sunvnet_common into a dynamically loadable
module and makes sunvnet and ldmvsw dependent on sunvnet_common.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: prevent bogus interrupt-mode fallbacks
EF10 VFs only support MSI-X interrupts, not MSI or legacy. This series
stops the probe logic from trying to fallback to those if MSI-X interrupt
probe fails. It also prevents selecting them with the interrupt_mode
module parameter.
This avoids producing messages like "failed to hook legacy IRQ 0" and "IRQ
handler type mismatch for IRQ 0", and ensures that the relevant error
(from the attempt to enable MSI-X) is reported to the caller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to probe interrupts with our minimum mode, return that error.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add min_interrupt_mode specification per NIC type.
It is a bit confusing because of "highest interrupt mode is less capable".
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
bridge: minor fdb cleanup
These patches aim to simplify the bridge fdb API a little by removing some
redundant functions and converting them into wrappers of a single function.
Also add proper lock checking to avoid future mistakes for the search
functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simplify the logic of entries pointing to the bridge by
converging the fdb_delete_by functions, this would allow us to use the
same function for both cases since the fdb's dst is set to NULL if it is
pointing to the bridge thus we can always check for a port match.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid new errors add checks to br_fdb_find and fdb_find_rcu
functions. The first requires hash_lock, the second obviously RCU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had 3 different fdb searching functions which was
confusing. This patch reduces all of them to one - fdb_find_rcu(), and
two flavors: br_fdb_find() which requires hash_lock and br_fdb_find_rcu
which requires RCU. This makes it clear what needs to be used, we also
remove two abusers of __br_fdb_get which called it under hash_lock and
replace them with br_fdb_find().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6097 chip requires watchdog_ops to be set.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back the goto that was removed by accident.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 40c81b25b1 ("sched: check negative err value to safe one level of indent")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had intended to say "sizeof(u32)" but the "u" is missing.
Fortunately, sizeof(32) is also 4, so the original code still works.
Fixes: c4e7beea21 ("net: qcom/emac: add ethtool support for reading hardware registers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use an intermediate variable to handle an error code
in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
'of_node_put(fpi->phy_node)' should also be called if we branch to
'out_deregister_fixed_link' error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=ol7H
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20170210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
afs: Use system UUID generation
There is now a general function for generating a UUID and AFS should make
use of it. It's also been recommended to me that I switch to using random
rather than time plus MAC address-based UUIDs which this function does.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
