It has been reported that sha1-avx2 can cause page faults by reading
beyond the end of the input. This patch disables it until it can be
fixed.
Cc: <stable@vger.kernel.org>
Fixes: 7c1da8d0d0 ("crypto: sha - SHA1 transform x86_64 AVX2")
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Implement extended LWSP/SWSP instruction subdecoding for the purpose of
unaligned GP-relative memory access emulation.
With the introduction of the MIPS16e2 ASE[1] the previously must-be-zero
3-bit field at bits 7..5 of the extended encodings of the instructions
selected with the LWSP and SWSP major opcodes has become a `sel' field,
acting as an opcode extension for additional operations. In both cases
the `sel' value of 0 has retained the original operation, that is:
LW rx, offset(sp)
and:
SW rx, offset(sp)
for LWSP and SWSP respectively. In hardware predating the MIPS16e2 ASE
other values may or may not have been decoded, architecturally yielding
unpredictable results, and in our unaligned memory access emulation we
have treated the 3-bit field as a don't-care, that is effectively making
all the possible encodings of the field alias to the architecturally
defined encoding of 0.
For the non-zero values of the `sel' field the MIPS16e2 ASE has in
particular defined these GP-relative operations:
LW rx, offset(gp) # sel = 1
LH rx, offset(gp) # sel = 2
LHU rx, offset(gp) # sel = 4
and
SW rx, offset(gp) # sel = 1
SH rx, offset(gp) # sel = 2
for LWSP and SWSP respectively, which will trap with an Address Error
exception if the effective address calculated is not naturally-aligned
for the operation requested. These operations have been selected for
unaligned access emulation, for consistency with the corresponding
regular MIPS and microMIPS operations.
For other non-zero values of the `sel' field the MIPS16e2 ASE has
defined further operations, which however either never trap with an
Address Error exception, such as LWL or GP-relative SB, or are not
supposed to be emulated, such as LL or SC. These operations have been
selected to exclude from unaligned access emulation, should an Address
Error exception ever happen with them.
Subdecode the `sel' field in unaligned access emulation then for the
extended encodings of the instructions selected with the LWSP and SWSP
major opcodes, whenever support for the MIPS16e2 ASE has been detected
in hardware, and either emulate the operation requested or send SIGBUS
to the originating process, according to the selection described above.
For hardware implementing the MIPS16 ASE, however lacking MIPS16e2 ASE
support retain the original interpretation of the `sel' field.
The effects of this change are illustrated with the following user
program:
$ cat mips16e2-test.c
#include <inttypes.h>
#include <stdio.h>
int main(void)
{
int64_t scratch[16] = { 0 };
int32_t *tmp0, *tmp1, *tmp2;
int i;
scratch[0] = 0xc8c7c6c5c4c3c2c1;
scratch[1] = 0xd0cfcecdcccbcac9;
asm volatile(
"move %0, $sp\n\t"
"move %1, $gp\n\t"
"move $sp, %4\n\t"
"addiu %2, %4, 8\n\t"
"move $gp, %2\n\t"
"lw %2, 2($sp)\n\t"
"sw %2, 16(%4)\n\t"
"lw %2, 2($gp)\n\t"
"sw %2, 24(%4)\n\t"
"lw %2, 1($sp)\n\t"
"sw %2, 32(%4)\n\t"
"lh %2, 1($gp)\n\t"
"sw %2, 40(%4)\n\t"
"lw %2, 3($sp)\n\t"
"sw %2, 48(%4)\n\t"
"lhu %2, 3($gp)\n\t"
"sw %2, 56(%4)\n\t"
"lw %2, 0(%4)\n\t"
"sw %2, 66($sp)\n\t"
"lw %2, 8(%4)\n\t"
"sw %2, 82($gp)\n\t"
"lw %2, 0(%4)\n\t"
"sw %2, 97($sp)\n\t"
"lw %2, 8(%4)\n\t"
"sh %2, 113($gp)\n\t"
"move $gp, %1\n\t"
"move $sp, %0"
: "=&d" (tmp0), "=&d" (tmp1), "=&d" (tmp2), "=m" (scratch)
: "d" (scratch));
for (i = 0; i < sizeof(scratch) / sizeof(*scratch); i += 2)
printf("%016" PRIx64 "\t%016" PRIx64 "\n",
scratch[i], scratch[i + 1]);
return 0;
}
$
to be compiled with:
$ gcc -mips16 -mips32r2 -Wa,-mmips16e2 -o mips16e2-test mips16e2-test.c
$
With 74Kf hardware, which does not implement the MIPS16e2 ASE, this
program produces the following output:
$ ./mips16e2-test
c8c7c6c5c4c3c2c1 d0cfcecdcccbcac9
00000000c6c5c4c3 00000000c6c5c4c3
00000000c5c4c3c2 00000000c5c4c3c2
00000000c7c6c5c4 00000000c7c6c5c4
0000c4c3c2c10000 0000000000000000
0000cccbcac90000 0000000000000000
000000c4c3c2c100 0000000000000000
000000cccbcac900 0000000000000000
$
regardless of whether the change has been applied or not.
With the change not applied and interAptive MR2 hardware[2], which does
implement the MIPS16e2 ASE, it produces the following output:
$ ./mips16e2-test
c8c7c6c5c4c3c2c1 d0cfcecdcccbcac9
00000000c6c5c4c3 00000000cecdcccb
00000000c5c4c3c2 00000000cdcccbca
00000000c7c6c5c4 00000000cfcecdcc
0000c4c3c2c10000 0000000000000000
0000000000000000 0000cccbcac90000
000000c4c3c2c100 0000000000000000
0000000000000000 000000cccbcac900
$
which shows that for GP-relative operations the correct trapping address
calculated from $gp has been obtained from the CP0 BadVAddr register and
so has data from the source operand, however masking and extension has
not been applied for halfword operations.
With the change applied and interAptive MR2 hardware the program
produces the following output:
$ ./mips16e2-test
c8c7c6c5c4c3c2c1 d0cfcecdcccbcac9
00000000c6c5c4c3 00000000cecdcccb
00000000c5c4c3c2 00000000ffffcbca
00000000c7c6c5c4 000000000000cdcc
0000c4c3c2c10000 0000000000000000
0000000000000000 0000cccbcac90000
000000c4c3c2c100 0000000000000000
0000000000000000 0000000000cac900
$
as expected.
References:
[1] "MIPS32 Architecture for Programmers: MIPS16e2 Application-Specific
Extension Technical Reference Manual", Imagination Technologies
Ltd., Document Number: MD01172, Revision 01.00, April 26, 2016
[2] "MIPS32 interAptiv Multiprocessing System Software User's Manual",
Imagination Technologies Ltd., Document Number: MD00904, Revision
02.01, June 15, 2016, Chapter 24 "MIPS16e Application-Specific
Extension to the MIPS32 Instruction Set", pp. 871-883
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16095/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Identify the presence of the MIPS16e2 ASE as per the architecture
specification[1], by checking for CP0 Config5.CA2 bit being 1[2].
References:
[1] "MIPS32 Architecture for Programmers: MIPS16e2 Application-Specific
Extension Technical Reference Manual", Imagination Technologies
Ltd., Document Number: MD01172, Revision 01.00, April 26, 2016,
Section 1.2 "Software Detection of the ASE", p. 5
[2] "MIPS32 interAptiv Multiprocessing System Software User's Manual",
Imagination Technologies Ltd., Document Number: MD00904, Revision
02.01, June 15, 2016, Section 2.2.1.6 "Device Configuration 5 --
Config5 (CP0 Register 16, Select 5)", pp. 71-72
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16094/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the real e820_tabel_firmware[] that will not be modified by the kernel
or the EFI boot stub under any circumstance.
In addition to that modify the code so that e820_table_firmwarep[] is
exposed via sysfs to represent the real firmware memory layout,
rather than exposing the e820_table_kexec[] table.
This fixes a hibernation bug/warning, which uses e820_table_kexec[] to check
RAM layout consistency across hibernation/resume:
The suspend kernel:
[ 0.000000] e820: update [mem 0x76671018-0x76679457] usable ==> usable
The resume kernel:
[ 0.000000] e820: update [mem 0x7666f018-0x76677457] usable ==> usable
...
[ 15.752088] PM: Using 3 thread(s) for decompression.
[ 15.752088] PM: Loading and decompressing image data (471870 pages)...
[ 15.764971] Hibernate inconsistent memory map detected!
[ 15.770833] PM: Image mismatch: architecture specific data
Actually it is safe to restore these pages because E820_TYPE_RAM and
E820_TYPE_RESERVED_KERN are treated the same during hibernation, so
the original e820 table provided by the bootloader is used for
hibernation MD5 fingerprint checking.
The side effect is that, this newly introduced variable might increase the
kernel size at compile time.
Suggested-by: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the e820_table_firmware[] table is mainly used by the kexec,
and it is not what it's supposed to be - despite its name it might be
modified by the kernel.
So change its name to e820_table_kexec[]. In the next patch we will
introduce the real e820_table_firmware[] table.
No functional change.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit in 2013:
77ea8c9489 ("x86: Reserve setup_data ranges late after parsing memmap cmdline")
has fixed the issue of losing setup_data information by deferring the
e820_reserve_setup_data() call until the early params have been parsed.
But this also introduced a new problem that, during early params parsing,
the kexec kernel might fake a mptable and saves it into the e820_table_firmware[]
table (without saving the mptable to the e820_table[]), however the subsequent
invoking of e820_reserve_setup_data() will overwrite the e820_table_firmware[]
according to the e820_table[], thus the fake mptable information is lost.
Fix this issue by updating the e820_table_firmware[] according to
the setup_data information, but without overwriting it.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The pat_enabled() logic is broken on CPUs which do not support PAT and
where the initialization code fails to call pat_init(). Due to that the
enabled flag stays true and pat_enabled() returns true wrongfully.
As a consequence the mappings, e.g. for Xorg, are set up with the wrong
caching mode and the required MTRR setups are omitted.
To cure this the following changes are required:
1) Make pat_enabled() return true only if PAT initialization was
invoked and successful.
2) Invoke init_cache_modes() unconditionally in setup_arch() and
remove the extra callsites in pat_disable() and the pat disabled
code path in pat_init().
Also rename __pat_enabled to pat_disabled to reflect the real purpose of
this variable.
Fixes: 9cd25aac1f ("x86/mm/pat: Emulate PAT when it is disabled")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bernhard Held <berny156@gmx.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@suse.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1707041749300.3456@file01.intranet.prod.int.rdu2.redhat.com
Zorro reported following crash while having enabled
syscall tracing (CONFIG_FTRACE_SYSCALLS):
Unable to handle kernel pointer dereference at virtual ...
Oops: 0011 [#1] SMP DEBUG_PAGEALLOC
SNIP
Call Trace:
([<000000000024d79c>] ftrace_syscall_enter+0xec/0x1d8)
[<00000000001099c6>] do_syscall_trace_enter+0x236/0x2f8
[<0000000000730f1c>] sysc_tracesys+0x1a/0x32
[<000003fffcf946a2>] 0x3fffcf946a2
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<000000000022dd44>] rb_event_data+0x34/0x40
---[ end trace 8c795f86b1b3f7b9 ]---
The crash happens in syscall_get_arguments function for
syscalls with zero arguments, that will try to access
first argument (args[0]) in event entry, but it's not
allocated.
Bail out of there are no arguments.
Cc: stable@vger.kernel.org
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After commmit 692f66f26a ("crash: move crashkernel parsing and vmcore
related code under CONFIG_CRASH_CORE") the KEXEC_NOTE_BYTES macro is not
used anymore and for s390 we create the ELF header in the new kernel
anyway. Therefore remove the macro.
Reported-by: Xunlei Pang <xpang@redhat.com>
Reviewed-by: Mikhail Zaslonko <zaslonko@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek RTD1295
and Action Semi S900. Both are fairly similar chips, used mainly in
set-top-boxes, but with other possible applications, and additional
members in the respective product families that could be added in the
future. The code here is fairly minimal, as all the interesting parts
are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWVo2eWCrR//JCVInAQLA6w/8CF+OI6BAw6dcW9BIqyZc80/tlYpbm39+
nKpCWEndQCxBubjAD/+lFuUB5sh/twsq6MYsnvRM3s4KTy6yzcZSO387AZLXAoSy
+OAyCd6JWQo4VrElPjTvzVWqCeuBjA/kh7x3cae+iYVREjKvwgyXNTIMKCtGWCcC
ClBa3FHdSWOaobRIfrGwwbHVahdOMKwEDPma1PaJ/eaIcGA2H/P1Lwyqf4z3ayka
mIPM6aWlwydFfJZYKiqzlSbN7ZMboB8SJf6xs56R9JUwybGU774OqTik2/pBbqJ3
RCtcEE5xq8xjC7s2frebLR/0amgoGqkCWSuj4ZU2AO+gg0sUnP3+cc1l6onkOleT
JdnPFZ/pU4PfYDbfnm8M36omybQmRMw2Y1pdI+GlVPX4qTK1bcz+jbWwI1+uu5w0
f0Q5oj/O4MKTCTro/ez6GlrnM9x5/ObQb3B3Zk6UcTLNYPp2BcyOKE57udLw3x8v
C2Rsn29sghKbmjD2cbSB6RvJdJezr5e2ZkRcKSuo5iLpJht1so4lwbbSJawrIwPm
MmvGLwfia33KIbwpfh4BYTUQ9+dFARBbbxPrm3fryPFx88cLlXSwjN09QH+8R70w
F3fed2EOr5/WvsqTazQarBSuqxCJ4uBvj3kjsc3f+bp1OjeofGqM9TwGVOxU7Rzy
O5YjLVKdfe4=
=771F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek
RTD1295 and Action Semi S900. Both are fairly similar chips, used
mainly in set-top-boxes, but with other possible applications, and
additional members in the respective product families that could be
added in the future. The code here is fairly minimal, as all the
interesting parts are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: remove duplicate entry
arm64: defconfig: enable Qualcomm Technologies EMAC and some PHY drivers
arm64: defconfig: enable QCOM_L2_PMU and QCOM_L3_PMU
arm64: defconfig: enable EDAC options
arm64: defconfig: enable APEI and GHES features
arm64: defconfig: enable support for PCIe hotplug
arm64: defconfig: enable EFI_CAPSULE_LOADER
arm64: defconfig: enable BLK_DEV_NVME
arm64: defconfig: enable ACPI_CPPC_CPUFREQ
arm64: marvell: enable ICU and GICP drivers
arm64: marvell: enable the Armada 7K/8K pinctrl driver
arm64: Prepare Actions Semi S900
ARM64: defconfig: enable meson SPICC as module
ARM64: defconfig: enable IR core, decoders and Meson IR device
arm64: defconfig: enable Simple Sound Card support
arm64: defconfig: Enable ARCH_BRCMSTB
arm64: defconfig: drop ARCH_VULCAN
arm64: disable Broadcom Vulcan platform
MAINTAINERS: Add Realtek section
ARM64: Prepare Realtek RTD1295
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
The main changes this time are from a cleanup series that Krzysztof
Kozłowski did, looking for config options in the defconfig files that
got removed or renamed. He tracked them down to make sure we don't
lose information unintentionally after an update.
Aside from that, there is the usual driver enablement, this time for
davinci, samsung, stm⅗2, bcm2835, qualcomm, at91, imx, mvebu, and omap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tmYq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"The main changes this time are from a cleanup series that Krzysztof
Kozłowski did, looking for config options in the defconfig files that
got removed or renamed. He tracked them down to make sure we don't
lose information unintentionally after an update.
Aside from that, there is the usual driver enablement, this time for
davinci, samsung, stm32, bcm2835, qualcomm, at91, imx, mvebu, and
omap"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
multi_v7_defconfig: Enable OMAP MTD and DM816 AHCI
ARM: qcom_defconfig: enable RPMSG_QCOM_SMD
ARM: imx_v6_v7_defconfig: Select CONFIG_IMX7D_ADC
ARM: mvebu: Enable SENSORS_PWM_FAN in defconfig
ARM: davinci_all_defconfig: enable USB CDC NCM gadget
ARM: davinci_all_defconfig: enable mtdtests
ARM: imx_v6_v7_defconfig: Set THERMAL_WRITABLE_TRIPS=y for testing
ARM: bcm2835_defconfig: Enable serial & ethernet USB gadget support
ARM: tct_hammer_defconfig: Save defconfig
ARM: s5pv210_defconfig: Save defconfig
ARM: s3c6400_defconfig: Save defconfig
ARM: mini2440_defconfig: Save defconfig
ARM: s3c2410_defconfig: Save defconfig
ARM: exynos_defconfig: Save defconfig
ARM: s5pv210_defconfig: Bring back lost (but wanted) options
ARM: s3c6400_defconfig: Bring back lost (but wanted) options
ARM: s3c2410_defconfig: Bring back lost (but wanted) options
ARM: tct_hammer_defconfig: Bring back lost (but wanted) options
ARM: mini2440_defconfig: Bring back lost (but wanted) options
ARM: defconfig: samsung: Re-order entries to match savedefconfig
...
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device
support for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H
with 10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module
plus board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600
and the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation
of the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards
are added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC platforms
from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much
more useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWVpLH2CrR//JCVInAQK5hxAAj8u8Y1RFWsfEXqAeGBme7PdiilEfm1ZR
U6wu6unW/zUb+QwQj52hzmYB9+FEd/bcNgw4AqEzypqMA+vJ6AP5tpujCrOXREsG
sk2LBnhOi/QbYfzIH6MYqjnrMbjSZ3LZpJ8+PSO+DpGwMkSKhWG5Jjjf1V69IbYJ
8eTpsnDbpo1OA4mtj+7fDxKGdH2WFx4922UuqTSzgoIqaTV1X2wcicpiJsfKynXY
3I9Apwhf/gKbtkWkVlNW7gxaAHONZOHEJ9rgIu6XoUCKbQrtbjZWEbKDUM1nJq5J
4ZYbd9r1HZvujuLk2/IuKTidmXj/4Q1FiIn4jqHINVqNj8dPKKYIoW5nU8rlbxG/
Ymy9WRY97YznWai49dnURGRbPNuiGyd9oaVsw7Wi1G2F4PgkAMgHs1rpERtIgnZg
ZzPxlXZdowYUgL6Qawk3//81QqGG/YL8VZ+VltPkjFNNYtEk0U+j3xW/n2ORAdvT
8EuNlTKid0Cq045nKkpAd5AWcgHIJe7IE3KiX/SpBtgH5PINlnUnwnm2f2TjRZCh
bw3g32er1JLSW9lAl6agu58lxox7NC1AV4Qy7Qk23IsR2mAv5gb5zad5GXwE41nT
qcyJ4OnDUpv/3f0LmH3WATQeHNnG8l8RgY8B6fH2GLlTQdmO7W7UTJ8tWU8E2sZ8
5xPePuor0JM=
=onXv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device support
for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H with
10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module plus
board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600 and
the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation of
the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards are
added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC
platforms from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much more
useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (345 commits)
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
ARM: pxa: Use - instead of @ for DT OPP entries
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
...
SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (a.k.a.
'owl') platform, a close relative of the S900 platform he adds for arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8F3w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (aka
'owl') platform, a close relative of the S900 platform he adds for
arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: owl: smp: Drop bogus holding pen
ARM: owl: Drop custom machine
ARM: owl: smp: Implement SPS power-gating for CPU2 and CPU3
soc: actions: owl-sps: Factor out owl_sps_set_pg() for power-gating
soc: actions: Add Owl SPS
dt-bindings: power: Add Owl SPS power domains
MAINTAINERS: Update Actions Semi section with SPS
ARM: owl: Implement CPU enable-method for S500
MAINTAINERS: Add Actions Semi Owl section
ARM: Prepare Actions Semi S500
ARM: socfpga: Increase max number of GPIOs
ARM: stm32: Introduce MACH_STM32F469 flag
ARM: prima2: remove redundant select CPU_V7
ARM: davinci: fix const warnings
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ALWAYS_ON
ARM: OMAP4: hwmod_data: add SHAM crypto accelerator
ARM: OMAP4: hwmod data: add des
ARM: OMAP4: hwmod data: add aes2
ARM: OMAP4: hwmod data: add aes1
ARM: pxa: Delete an error message for a failed memory allocation in pxa3xx_u2d_probe()
...
Smaller patches that didn't seem to find a home in other branches, and
low-priority fixes from late in the merge window.
- Lee Jones retires as bcm2835 (raspberry pi) co-maintainer.
- A couple of bugfixes for the ARM CCN bus driver that were
regarded not important enough
- minor device tree fixes for the Renesas and Marvell platforms,
that came a little late or did not justify have another
pull request after the last -rc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MBxL
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Arnd Bergmann:
"Smaller patches that didn't seem to find a home in other branches, and
low-priority fixes from late in the merge window.
- Lee Jones retires as bcm2835 (raspberry pi) co-maintainer.
- a couple of bugfixes for the ARM CCN bus driver that were regarded
not important enough
- minor device tree fixes for the Renesas and Marvell platforms, that
came a little late or did not justify have another pull request
after the last -rc"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Enable stats for CCN-502 interconnect
dt-bindings: arm-ccn: Add bindings info for CCN-502 compatible string
bus: arm-ccn: Use devm_kcalloc() in arm_ccn_probe()
bus: arm-ccn: Fix module autoload
MAINTAINERS: add RV1108 Rockchip soc to maintained files
ARM: dts: kirkwood: Fix Openblock A6 nand partition overlap
ARM: dts: armadillo800eva: Split LCD mux and gpio
MAINTAINERS: Remove Lee Jones from bcm2835.
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zJi3
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
The functions handle_uv2_busy, uv_flush_send_and_wait and
find_another_by_swack are local to the source, so make them static.
Also remove normal_busy as it is no longer used.
Fixes various smatch warnings, such as:
"symbol 'find_another_by_swack' was not declared. Should it be static?"
"symbol 'handle_uv2_busy' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Andrew Banman <abanman@hpe.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/20170704083129.10559-1-colin.king@canonical.com
It's easier for host applications, such as QEMU, if they can always
access guest MSR_IA32_BNDCFGS in VMCS, even though MPX is disabled in
guest cpuid.
Cc: stable@vger.kernel.org
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different USB
drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpavQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJrgCgp8Pso8bs+bnIknUSQFSguWd3wM0AnA8X3NHf
lrdCuqw+2oxGOQrecacz
=5L4Q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
All code that patches kernel text has been moved over to using
patch_instruction() and patch_instruction() is able to cope with the
kernel text being read only.
The linker script has been updated to ensure the read only data ends
on a large page boundary, so it and the preceding kernel text can be
marked R_X. We also have implementations of mark_rodata_ro() for Hash
and Radix MMU modes.
There are some corner-cases missing when the kernel is built
relocatable, so for now make it depend on !RELOCATABLE.
There's also a temporary workaround to depend on !HIBERNATION to avoid
a build failure, that will be removed once we've merged with the PM
tree.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Make it depend on !RELOCATABLE, munge change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Radix linear mapping code (create_physical_mapping()) tries to use
the largest page size it can at each step. Currently the only reason
it steps down to a smaller page size is if the start addr is
unaligned (never happens in practice), or the end of memory is not
aligned to a huge page boundary.
To support STRICT_RWX we need to break the mapping at __init_begin,
so that the text and rodata prior to that can be marked R_X and the
regular pages after can be marked RW.
Having done that we can now implement mark_rodata_ro() for Radix,
knowing that we won't need to split any mappings.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Split down to PAGE_SIZE, not 2MB, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With hash we update the bolted pte to mark it read-only. We rely
on the MMU_FTR_KERNEL_RO to generate the correct permissions
for read-only text. The radix implementation just prints a warning
in this implementation
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Make the warning louder when we don't have MMU_FTR_KERNEL_RO]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull RAS updates from Thomas Gleixner:
"The RAS updates for the 4.13 merge window:
- Cleanup of the MCE injection facility (Borsilav Petkov)
- Rework of the AMD/SMCA handling (Yazen Ghannam)
- Enhancements for ACPI/APEI to handle new notitication types (Shiju
Jose)
- atomic_t to refcount_t conversion (Elena Reshetova)
- A few fixes and enhancements all over the place"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
RAS/CEC: Check the correct variable in the debugfs error handling
x86/mce: Always save severity in machine_check_poll()
x86/MCE, xen/mcelog: Make /dev/mcelog registration messages more precise
x86/mce: Update bootlog description to reflect behavior on AMD
x86/mce: Don't disable MCA banks when offlining a CPU on AMD
x86/mce/mce-inject: Preset the MCE injection struct
x86/mce: Clean up include files
x86/mce: Get rid of register_mce_write_callback()
x86/mce: Merge mce_amd_inj into mce-inject
x86/mce/AMD: Use saved threshold block info in interrupt handler
x86/mce/AMD: Use msr_stat when clearing MCA_STATUS
x86/mce/AMD: Carve out SMCA bank configuration
x86/mce/AMD: Redo error logging from APIC LVT interrupt handlers
x86/mce: Convert threshold_bank.cpus from atomic_t to refcount_t
RAS: Make local function parse_ras_param() static
ACPI/APEI: Handle GSIV and GPIO notification types
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
Pull x86 timers updates from Thomas Gleixner:
"This update contains:
- The solution for the TSC deadline timer borkage, which is caused by
a hardware problem in the TSC_ADJUST/TSC_DEADLINE_TIMER logic.
The problem is documented now and fixed with a microcode update, so
we can remove the workaround and just check for the microcode version.
If the microcode is not up to date, then the TSC deadline timer is
disabled. If the borkage is fixed by the proper microcode version,
then the deadline timer can be used. In both cases the restrictions
to the range of the TSC_ADJUST value, which were added as
workarounds, are removed.
- A few simple fixes and updates to the timer related x86 code"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Call check_system_tsc_reliable() before unsynchronized_tsc()
x86/hpet: Do not use smp_processor_id() in preemptible code
x86/time: Make setup_default_timer_irq() static
x86/tsc: Remove the TSC_ADJUST clamp
x86/apic: Add TSC_DEADLINE quirk due to errata
x86/apic: Change the lapic name in deadline mode
Pull x86 PCI updates from Thomas Gleixner:
"This update provides the seperation of x86 PCI accessors from the
global PCI lock in the generic PCI config space accessors.
The reasons for this are:
- x86 has it's own PCI config lock for various reasons, so the
accessors have to lock two locks nested.
- The ECAM (mmconfig) access to the extended configuration space does
not require locking. The existing generic locking causes a massive
lock contention when accessing the extended config space of the
Uncore facility for performance monitoring.
The commit which switched the access to the primary config space over
to ECAM mode has been removed from the branch, so the primary config
space is still accessed with type1 accessors properly serialized by
the x86 internal locking.
Bjorn agreed on merging this through the x86 tree"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/PCI: Select CONFIG_PCI_LOCKLESS_CONFIG
PCI: Provide Kconfig option for lockless config space accessors
x86/PCI/ce4100: Properly lock accessor functions
x86/PCI: Abort if legacy init fails
x86/PCI: Remove duplicate defines
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- Expand the generic infrastructure handling the irq migration on CPU
hotplug and convert X86 over to it. (Thomas Gleixner)
Aside of consolidating code this is a preparatory change for:
- Finalizing the affinity management for multi-queue devices. The
main change here is to shut down interrupts which are affine to a
outgoing CPU and reenabling them when the CPU comes online again.
That avoids moving interrupts pointlessly around and breaking and
reestablishing affinities for no value. (Christoph Hellwig)
Note: This contains also the BLOCK-MQ and NVME changes which depend
on the rework of the irq core infrastructure. Jens acked them and
agreed that they should go with the irq changes.
- Consolidation of irq domain code (Marc Zyngier)
- State tracking consolidation in the core code (Jeffy Chen)
- Add debug infrastructure for hierarchical irq domains (Thomas
Gleixner)
- Infrastructure enhancement for managing generic interrupt chips via
devmem (Bartosz Golaszewski)
- Constification work all over the place (Tobias Klauser)
- Two new interrupt controller drivers for MVEBU (Thomas Petazzoni)
- The usual set of fixes, updates and enhancements all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
irqchip/or1k-pic: Fix interrupt acknowledgement
irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap
irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity
nvme: Allocate queues for all possible CPUs
blk-mq: Create hctx for each present CPU
blk-mq: Include all present CPUs in the default queue mapping
genirq: Avoid unnecessary low level irq function calls
genirq: Set irq masked state when initializing irq_desc
genirq/timings: Add infrastructure for estimating the next interrupt arrival time
genirq/timings: Add infrastructure to track the interrupt timings
genirq/debugfs: Remove pointless NULL pointer check
irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID
irqchip/gic-v3-its: Add ACPI NUMA node mapping
irqchip/gic-v3-its-platform-msi: Make of_device_ids const
irqchip/gic-v3-its: Make of_device_ids const
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU
genirq/irqdomain: Remove auto-recursive hierarchy support
irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access
...
Pull timer updates from Thomas Gleixner:
"A rather large update for timers/timekeeping:
- compat syscall consolidation (Al Viro)
- Posix timer consolidation (Christoph Helwig / Thomas Gleixner)
- Cleanup of the device tree based initialization for clockevents and
clocksources (Daniel Lezcano)
- Consolidation of the FTTMR010 clocksource/event driver (Linus
Walleij)
- The usual set of small fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (93 commits)
timers: Make the cpu base lock raw
clocksource/drivers/mips-gic-timer: Fix an error code in 'gic_clocksource_of_init()'
clocksource/drivers/fsl_ftm_timer: Unmap region obtained by of_iomap
clocksource/drivers/tcb_clksrc: Make IO endian agnostic
clocksource/drivers/sun4i: Switch to the timer-of common init
clocksource/drivers/timer-of: Fix invalid iomap check
Revert "ktime: Simplify ktime_compare implementation"
clocksource/drivers: Fix uninitialized variable use in timer_of_init
kselftests: timers: Add test for frequency step
kselftests: timers: Fix inconsistency-check to not ignore first timestamp
time: Add warning about imminent deprecation of CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Clean up CLOCK_MONOTONIC_RAW time handling
posix-cpu-timers: Make timespec to nsec conversion safe
itimer: Make timeval to nsec conversion range limited
timers: Fix parameter description of try_to_del_timer_sync()
ktime: Simplify ktime_compare implementation
clocksource/drivers/fttmr010: Factor out clock read code
clocksource/drivers/fttmr010: Implement delay timer
clocksource/drivers: Add timer-of common init routine
clocksource/drivers/tcb_clksrc: Save timer context on suspend/resume
...
on MMU targets EFAULT is possible here. Make both return 0 or error,
passing what used to be the return value of flat_get_addr_from_rp()
by reference.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull s390 updates from Martin Schwidefsky:
"The bulk of the s390 patches for 4.13. Some new things but mostly bug
fixes and cleanups. Noteworthy changes:
- The SCM block driver is converted to blk-mq
- Switch s390 to 5 level page tables. The virtual address space for a
user space process can now have up to 16EB-4KB.
- Introduce a ELF phdr flag for qemu to avoid the global
vm.alloc_pgste which forces all processes to large page tables
- A couple of PCI improvements to improve error recovery
- Included is the merge of the base support for proper machine checks
for KVM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
s390/dasd: Fix faulty ENODEV for RO sysfs attribute
s390/pci: recognize name clashes with uids
s390/pci: provide more debug information
s390/pci: fix handling of PEC 306
s390/pci: improve pci hotplug
s390/pci: introduce clp_get_state
s390/pci: improve error handling during fmb (de)registration
s390/pci: improve unreg_ioat error handling
s390/pci: improve error handling during interrupt deregistration
s390/pci: don't cleanup in arch_setup_msi_irqs
KVM: s390: Backup the guest's machine check info
s390/nmi: s390: New low level handling for machine check happening in guest
s390/fpu: export save_fpu_regs for all configs
s390/kvm: avoid global config of vm.alloc_pgste=1
s390: rename struct psw_bits members
s390: rename psw_bits enums
s390/mm: use correct address space when enabling DAT
s390/cio: introduce io_subchannel_type
s390/ipl: revert Load Normal semantics for LPAR CCW-type re-IPL
s390/dumpstack: remove raw stack dump
...
Pull parisc updates from Helge Deller:
"Main changes are:
- Added support to the parisc dma functions to return DMA_ERROR_CODE
if DMA isn't possible. This fixes a long standing kernel crash if
parport_pc is enabled (by Thomas Bogendoerfer, marked for stable
series).
- Use the compat_sys_keyctl() in compat mode (by Eric Biggers, marked
for stable series).
- Initial support for the Page Deallocation Table (PDT) which is
maintained by firmware and holds the list of memory addresses which
had physical errors. By checking that list we can prevent Linux to
use those broken memory areas.
- Ensure IRQs are off in switch_mm().
- Report SIGSEGV instead of SIGBUS when running out of stack.
- Mark the cr16 clocksource stable on single-socket and single-core
machines"
* 'parisc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: DMA API: return error instead of BUG_ON for dma ops on non dma devs
parisc: Report SIGSEGV instead of SIGBUS when running out of stack
parisc: use compat_sys_keyctl()
parisc: Don't hardcode PSW values in hpmc code
parisc: Don't hardcode PSW values in gsc_*() functions
parisc: Avoid zeroing gr[0] in fixup_exception()
parisc/mm: Ensure IRQs are off in switch_mm()
parisc: Add Page Deallocation Table (PDT) support
parisc: Enhance detection of synchronous cr16 clocksources
parisc: Drop per_cpu uaccess related exception_data struct
parisc: Inline trivial exception code in lusercopy.S
Pull x86 mm updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued work to add support for 5-level paging provided by future
Intel CPUs. In particular we switch the x86 GUP code to the generic
implementation. (Kirill A. Shutemov)
- Continued work to add PCID CPU support to native kernels as well.
In this round most of the focus is on reworking/refreshing the TLB
flush infrastructure for the upcoming PCID changes. (Andy
Lutomirski)"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
x86/mm: Delete a big outdated comment about TLB flushing
x86/mm: Don't reenter flush_tlb_func_common()
x86/KASLR: Fix detection 32/64 bit bootloaders for 5-level paging
x86/ftrace: Exclude functions in head64.c from function-tracing
x86/mmap, ASLR: Do not treat unlimited-stack tasks as legacy mmap
x86/mm: Remove reset_lazy_tlbstate()
x86/ldt: Simplify the LDT switching logic
x86/boot/64: Put __startup_64() into .head.text
x86/mm: Add support for 5-level paging for KASLR
x86/mm: Make kernel_physical_mapping_init() support 5-level paging
x86/mm: Add sync_global_pgds() for configuration with 5-level paging
x86/boot/64: Add support of additional page table level during early boot
x86/boot/64: Rename init_level4_pgt and early_level4_pgt
x86/boot/64: Rewrite startup_64() in C
x86/boot/compressed: Enable 5-level paging during decompression stage
x86/boot/efi: Define __KERNEL32_CS GDT on 64-bit configurations
x86/boot/efi: Fix __KERNEL_CS definition of GDT entry on 64-bit configurations
x86/boot/efi: Cleanup initialization of GDT entries
x86/asm: Fix comment in return_from_SYSCALL_64()
x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation
...
Pull x86 microcode updates from Ingo Molnar:
"The main changes are a fix early microcode application for
resume-from-RAM, plus a 32-bit initrd placement fix - by Borislav
Petkov"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Make a couple of symbols static
x86/microcode/intel: Save pointer to ucode patch for early AP loading
x86/microcode: Look for the initrd at the correct address on 32-bit
Pull x86 hyperv updates from Ingo Molnar:
"Avoid boot time TSC calibration on Hyper-V hosts, to improve
calibration robustness. (Vitaly Kuznetsov)"
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyperv: Read TSC frequency from a synthetic MSR
x86/hyperv: Check frequency MSRs presence according to the specification
Pull x86 debug update from Ingo Molnar:
"A single fix for an off-by one bug in test_nmi_ipi() that probably
doesn't matter in practice"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Fix timeout test in test_nmi_ipi()
Pull x86 cleanups from Ingo Molnar:
"Two small cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/paravirt: Remove unnecessary return from void function
x86/boot: Add missing strchr() declaration
Pull x86 boot updates from Ingo Molnar:
"The main changes in this cycle were KASLR improvements for rare
environments with special boot options, by Baoquan He. Also misc
smaller changes/cleanups"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Extend the lower bound of crash kernel low reservations
x86/boot: Remove unused copy_*_gs() functions
x86/KASLR: Use the right memcpy() implementation
Documentation/kernel-parameters.txt: Update 'memmap=' boot option description
x86/KASLR: Handle the memory limit specified by the 'memmap=' and 'mem=' boot options
x86/KASLR: Parse all 'memmap=' boot option entries
Pull x86 asm updates from Ingo Molnar:
"A single commit micro-optimizing short user copies on certain Intel
CPUs"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uaccess: Optimize copy_user_enhanced_fast_string() for short strings
Pull x86 apic updates from Ingo Molnar:
"Janitorial changes: removal of an unused function plus __init
annotations"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Make arch_init_msi/htirq_domain __init
x86/apic: Make init_legacy_irqs() __init
x86/ioapic: Remove unused IO_APIC_irq_trigger() function
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Add the SYSTEM_SCHEDULING bootup state to move various scheduler
debug checks earlier into the bootup. This turns silent and
sporadically deadly bugs into nice, deterministic splats. Fix some
of the splats that triggered. (Thomas Gleixner)
- A round of restructuring and refactoring of the load-balancing and
topology code (Peter Zijlstra)
- Another round of consolidating ~20 of incremental scheduler code
history: this time in terms of wait-queue nomenclature. (I didn't
get much feedback on these renaming patches, and we can still
easily change any names I might have misplaced, so if anyone hates
a new name, please holler and I'll fix it.) (Ingo Molnar)
- sched/numa improvements, fixes and updates (Rik van Riel)
- Another round of x86/tsc scheduler clock code improvements, in hope
of making it more robust (Peter Zijlstra)
- Improve NOHZ behavior (Frederic Weisbecker)
- Deadline scheduler improvements and fixes (Luca Abeni, Daniel
Bristot de Oliveira)
- Simplify and optimize the topology setup code (Lauro Ramos
Venancio)
- Debloat and decouple scheduler code some more (Nicolas Pitre)
- Simplify code by making better use of llist primitives (Byungchul
Park)
- ... plus other fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
sched/cputime: Refactor the cputime_adjust() code
sched/debug: Expose the number of RT/DL tasks that can migrate
sched/numa: Hide numa_wake_affine() from UP build
sched/fair: Remove effective_load()
sched/numa: Implement NUMA node level wake_affine()
sched/fair: Simplify wake_affine() for the single socket case
sched/numa: Override part of migrate_degrades_locality() when idle balancing
sched/rt: Move RT related code from sched/core.c to sched/rt.c
sched/deadline: Move DL related code from sched/core.c to sched/deadline.c
sched/cpuset: Only offer CONFIG_CPUSETS if SMP is enabled
sched/fair: Spare idle load balancing on nohz_full CPUs
nohz: Move idle balancer registration to the idle path
sched/loadavg: Generalize "_idle" naming to "_nohz"
sched/core: Drop the unused try_get_task_struct() helper function
sched/fair: WARN() and refuse to set buddy when !se->on_rq
sched/debug: Fix SCHED_WARN_ON() to return a value on !CONFIG_SCHED_DEBUG as well
sched/wait: Disambiguate wq_entry->task_list and wq_head->task_list naming
sched/wait: Move bit_wait_table[] and related functionality from sched/core.c to sched/wait_bit.c
sched/wait: Split out the wait_bit*() APIs from <linux/wait.h> into <linux/wait_bit.h>
sched/wait: Re-adjust macro line continuation backslashes in <linux/wait.h>
...
Pull perf updates from Ingo Molnar:
"Most of the changes are for tooling, the main changes in this cycle were:
- Improve Intel-PT hardware tracing support, both on the kernel and
on the tooling side: PTWRITE instruction support, power events for
C-state tracing, etc. (Adrian Hunter)
- Add support to measure SMI cost to the x86 architecture, with
tooling support in 'perf stat' (Kan Liang)
- Support function filtering in 'perf ftrace', plus related
improvements (Namhyung Kim)
- Allow adding and removing fields to the default 'perf script'
columns, using + or - as field prefixes to do so (Andi Kleen)
- Allow resolving the DSO name with 'perf script -F brstack{sym,off},dso'
(Mark Santaniello)
- Add perf tooling unwind support for PowerPC (Paolo Bonzini)
- ... and various other improvements as well"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (84 commits)
perf auxtrace: Add CPU filter support
perf intel-pt: Do not use TSC packets for calculating CPU cycles to TSC
perf intel-pt: Update documentation to include new ptwrite and power events
perf intel-pt: Add example script for power events and PTWRITE
perf intel-pt: Synthesize new power and "ptwrite" events
perf intel-pt: Move code in intel_pt_synth_events() to simplify attr setting
perf intel-pt: Factor out intel_pt_set_event_name()
perf intel-pt: Tidy messages into called function intel_pt_synth_event()
perf intel-pt: Tidy Intel PT evsel lookup into separate function
perf intel-pt: Join needlessly wrapped lines
perf intel-pt: Remove unused instructions_sample_period
perf intel-pt: Factor out common code synthesizing event samples
perf script: Add synthesized Intel PT power and ptwrite events
perf/x86/intel: Constify the 'lbr_desc[]' array and make a function static
perf script: Add 'synth' field for synthesized event payloads
perf auxtrace: Add itrace option to output power events
perf auxtrace: Add itrace option to output ptwrite events
tools include: Add byte-swapping macros to kernel.h
perf script: Add 'synth' event type for synthesized events
x86/insn: perf tools: Add new ptwrite instruction
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Add CONFIG_REFCOUNT_FULL=y to allow the disabling of the 'full'
(robustness checked) refcount_t implementation with slightly lower
runtime overhead. (Kees Cook)
The lighter weight variant is the default. The two variants use the
same API. Having this variant was a precondition by some
maintainers to merge refcount_t cleanups.
- Add lockdep support for rtmutexes (Peter Zijlstra)
- liblockdep fixes and improvements (Sasha Levin, Ben Hutchings)
- ... misc fixes and improvements"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
locking/refcount: Remove the half-implemented refcount_sub() API
locking/refcount: Create unchecked atomic_t implementation
locking/rtmutex: Don't initialize lockdep when not required
locking/selftest: Add RT-mutex support
locking/selftest: Remove the bad unlock ordering test
rt_mutex: Add lockdep annotations
MAINTAINERS: Claim atomic*_t maintainership
locking/x86: Remove the unused atomic_inc_short() methd
tools/lib/lockdep: Remove private kernel headers
tools/lib/lockdep: Hide liblockdep output from test results
tools/lib/lockdep: Add dummy current_gfp_context()
tools/include: Add IS_ERR_OR_NULL to err.h
tools/lib/lockdep: Add empty __is_[module,kernel]_percpu_address
tools/lib/lockdep: Include err.h
tools/include: Add (mostly) empty include/linux/sched/mm.h
tools/lib/lockdep: Use LDFLAGS
tools/lib/lockdep: Remove double-quotes from soname
tools/lib/lockdep: Fix object file paths used in an out-of-tree build
tools/lib/lockdep: Fix compilation for 4.11
tools/lib/lockdep: Don't mix fd-based and stream IO
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Rework the EFI capsule loader to allow for workarounds for
non-compliant firmware (Ard Biesheuvel)
- Implement a capsule loader quirk for Quark X102x (Jan Kiszka)
- Enable SMBIOS/DMI support for the ARM architecture (Ard Biesheuvel)
- Add CONFIG_EFI_PGT_DUMP=y support for x86-32 and kexec (Sai
Praneeth)
- Fixes for EFI support for Xen dom0 guests running under x86-64
hosts (Daniel Kiper)"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen/efi: Initialize only the EFI struct members used by Xen
efi: Process the MEMATTR table only if EFI_MEMMAP is enabled
efi/arm: Enable DMI/SMBIOS
x86/efi: Extend CONFIG_EFI_PGT_DUMP support to x86_32 and kexec as well
efi/efi_test: Use memdup_user() helper
efi/capsule: Add support for Quark security header
efi/capsule-loader: Use page addresses rather than struct page pointers
efi/capsule-loader: Redirect calls to efi_capsule_setup_info() via weak alias
efi/capsule: Remove NULL test on kmap()
efi/capsule-loader: Use a cached copy of the capsule header
efi/capsule: Adjust return type of efi_capsule_setup_info()
efi/capsule: Clean up pr_err/_info() messages
efi/capsule: Remove pr_debug() on ENOMEM or EFAULT
efi/capsule: Fix return code on failing kmap/vmap
Pull objtool updates from Ingo Molnar:
"This is an extensive rewrite of the objdump tool to track all stack
pointer modifications through the machine instructions of disassembled
functions found in kernel .o files.
This re-design removes the prior dependency on CONFIG_FRAME_POINTERS,
with the goal to prepare the tool to generate kernel debuginfo data in
the future. There's also an increase in checking/tracking robustness
as a side effect as well.
No (intended) changes to existing functionality"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Silence warnings for functions which use IRET
objtool: Implement stack validation 2.0
objtool, x86: Add several functions and files to the objtool whitelist
objtool: Move checking code to check.c
Pull core block/IO updates from Jens Axboe:
"This is the main pull request for the block layer for 4.13. Not a huge
round in terms of features, but there's a lot of churn related to some
core cleanups.
Note this depends on the UUID tree pull request, that Christoph
already sent out.
This pull request contains:
- A series from Christoph, unifying the error/stats codes in the
block layer. We now use blk_status_t everywhere, instead of using
different schemes for different places.
- Also from Christoph, some cleanups around request allocation and IO
scheduler interactions in blk-mq.
- And yet another series from Christoph, cleaning up how we handle
and do bounce buffering in the block layer.
- A blk-mq debugfs series from Bart, further improving on the support
we have for exporting internal information to aid debugging IO
hangs or stalls.
- Also from Bart, a series that cleans up the request initialization
differences across types of devices.
- A series from Goldwyn Rodrigues, allowing the block layer to return
failure if we will block and the user asked for non-blocking.
- Patch from Hannes for supporting setting loop devices block size to
that of the underlying device.
- Two series of patches from Javier, fixing various issues with
lightnvm, particular around pblk.
- A series from me, adding support for write hints. This comes with
NVMe support as well, so applications can help guide data placement
on flash to improve performance, latencies, and write
amplification.
- A series from Ming, improving and hardening blk-mq support for
stopping/starting and quiescing hardware queues.
- Two pull requests for NVMe updates. Nothing major on the feature
side, but lots of cleanups and bug fixes. From the usual crew.
- A series from Neil Brown, greatly improving the bio rescue set
support. Most notably, this kills the bio rescue work queues, if we
don't really need them.
- Lots of other little bug fixes that are all over the place"
* 'for-4.13/block' of git://git.kernel.dk/linux-block: (217 commits)
lightnvm: pblk: set line bitmap check under debug
lightnvm: pblk: verify that cache read is still valid
lightnvm: pblk: add initialization check
lightnvm: pblk: remove target using async. I/Os
lightnvm: pblk: use vmalloc for GC data buffer
lightnvm: pblk: use right metadata buffer for recovery
lightnvm: pblk: schedule if data is not ready
lightnvm: pblk: remove unused return variable
lightnvm: pblk: fix double-free on pblk init
lightnvm: pblk: fix bad le64 assignations
nvme: Makefile: remove dead build rule
blk-mq: map all HWQ also in hyperthreaded system
nvmet-rdma: register ib_client to not deadlock in device removal
nvme_fc: fix error recovery on link down.
nvmet_fc: fix crashes on bad opcodes
nvme_fc: Fix crash when nvme controller connection fails.
nvme_fc: replace ioabort msleep loop with completion
nvme_fc: fix double calls to nvme_cleanup_cmd()
nvme-fabrics: verify that a controller returns the correct NQN
nvme: simplify nvme_dev_attrs_are_visible
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWVpGxCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SGMAKCP9mGjMWqD
Z9uCT8swDJ8LCi/o+wCfV4Cs0eWzqkJUDMaycdJrlMjB174=
=TavE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "late dt64 for 4.13" from Gregory CLEMENT:
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
* tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
EPT A/D was enabled in the vmcs02 EPTP regardless of the vmcs12's EPTP
value. The problem is that enabling A/D changes the behavior of L2's
x86 page table walks as seen by L1. With A/D enabled, x86 page table
walks are always treated as EPT writes.
Commit ae1e2d1082 ("kvm: nVMX: support EPT accessed/dirty bits",
2017-03-30) tried to work around this problem by clearing the write
bit in the exit qualification for EPT violations triggered by page
walks. However, that fixup introduced the opposite bug: page-table walks
that actually set x86 A/D bits were *missing* the write bit in the exit
qualification.
This patch fixes the problem by disabling EPT A/D in the shadow MMU
when EPT A/D is disabled in vmcs12's EPTP.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For CONFIG_STRICT_KERNEL_RWX align __init_begin to 16M. We use 16M
since its the larger of 2M on radix and 16M on hash for our linear
mapping. The plan is to have .text, .rodata and everything upto
__init_begin marked as RX. Note we still have executable read only
data. We could further align rodata to another 16M boundary. I've used
keeping text plus rodata as read-only-executable as a trade-off to
doing read-only-executable for text and read-only for rodata.
We don't use multi PT_LOAD in PHDRS because we are not sure if all
bootloaders support them. This patch keeps PHDRS in vmlinux.lds.S as
the same they are with just one PT_LOAD for all of the kernel marked
as RWX (7).
mpe: What this means is the added alignment bloats the resulting
binary on disk, a powernv kernel goes from 17M to 22M.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch creates the window using text_poke_area, allocated via
get_vm_area(). text_poke_area is per CPU to avoid locking.
text_poke_area for each cpu is setup using late_initcall, prior to
setup of these alternate mapping areas, we continue to use direct
write to change/modify kernel text. With the ability to use alternate
mappings to write to kernel text, it provides us the freedom to then
turn text read-only and implement CONFIG_STRICT_KERNEL_RWX.
This code is CPU hotplug aware to ensure that the we have mappings for
any new cpus as they come online and tear down mappings for any CPUs
that go offline.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move from mwrite() to patch_instruction() for xmon for
breakpoint addition and removal.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So that we can implement STRICT_RWX, use patch_instruction() in
optprobes.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_arm/disarm_probe() use direct assignment for copying
instructions, replace them with patch_instruction(). We don't need to
call flush_icache_range() because patch_instruction() does it for us.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 9abcc981de ("powerpc/mm/radix: Only add X for pages
overlapping kernel text") changed the linear mapping on Radix to only
mark the kernel text executable.
However if the kernel is run relocated, for example as a kdump kernel,
then the exception vectors are split from the kernel text, ie. they
remain at real address 0.
We tend to get away with it, because the kernel itself will usually be
below 1G, which means the 1G page at 0-1G is marked executable and
everything works OK. However if the kernel is loaded above 1G, or the
system has less than 1G in total (meaning we can't use a 1G page),
then the exception vectors will not be marked executable and the
kernel will fail to boot.
Fix it by also checking if the address range overlaps the exception
vectors when deciding if we should add PAGE_KERNEL_X.
Fixes: 9abcc981de ("powerpc/mm/radix: Only add X for pages overlapping kernel text")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Combine with the existing check, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Once upon a time there were only two PP (page protection) bits. In ISA
2.03 an additional PP bit was added, but because of the layout of the
HPTE it could not be made contiguous with the existing PP bits.
The result is that we now have three PP bits, named pp0, pp1, pp2,
where pp0 occupies bit 63 of dword 1 of the HPTE and pp1 and pp2
occupy bits 1 and 0 respectively. Until recently Linux hasn't used
pp0, however with the addition of _PAGE_KERNEL_RO we started using it.
The problem arises in the LPAR code, where we need to translate the PP
bits into the argument for the H_PROTECT hypercall. Currently the code
only passes bits 0-2 of newpp, which covers pp1, pp2 and N (no
execute), meaning pp0 is not passed to the hypervisor at all.
We can't simply pass it through in bit 63, as that would collide with a
different field in the flags argument, as defined in PAPR. Instead we
have to shift it down to bit 8 (IBM bit 55).
Fixes: e58e87adc8 ("powerpc/mm: Update _PAGE_KERNEL_RO")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Simplify the test, rework change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We can't take traps with relocation off, so blacklist enter_rtas() and
rtas_return_loc(). However, instead of blacklisting all of enter_rtas(),
introduce a new symbol __enter_rtas from where on we can't take a trap
and blacklist that.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Blacklist all functions involved while handling a trap. We:
- convert some of the symbols into private symbols, and
- blacklist most functions involved while handling a trap.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is actually safe to probe system_call() in entry_64.S, but only till
we unset MSR_RI. To allow this, add a new symbol system_call_exit()
after the mtmsrd and blacklist that.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is common to get a PMU interrupt right after the mtmsr instruction that
enables interrupts. Due to this, the stack trace profile gets needlessly split
across system_call_common() and system_call().
Previously, system_call() symbol was at the current place to hide a few
earlier symbols which have since been made private or removed entirely.
So, let's move system_call() slightly higher up, right after the mtmsr
instruction that enables interrupts. Convert existing references to
system_call to a local syscall symbol.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert some of the symbols into private symbols and blacklist
system_call_common() and system_call() from kprobes. We can't take a
trap at parts of these functions as either MSR_RI is unset or the
kernel stack pointer is not yet setup.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Don't convert system_call_common to _GLOBAL()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit b48bbb82e2 ("powerpc/64s: Don't unbalance the return branch
predictor in __replay_interrupt()") introduced __replay_interrupt_return
symbol with '.L' prefix in hopes of keeping it private. However, due to
the use of LOAD_REG_ADDR(), the assembler kept this symbol visible. Fix
the same by instead using the local label '1'.
Fixes: Commit b48bbb82e2 ("powerpc/64s: Don't unbalance the return branch
predictor in __replay_interrupt()")
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we assume that the function pointer we receive in
ppc_function_entry() points to a function descriptor. However, this is
not always the case. In particular, assembly symbols without the right
annotation do not have an associated function descriptor. Some of these
symbols are added to the kprobe blacklist using _ASM_NOKPROBE_SYMBOL().
When such addresses are subsequently processed through
arch_deref_entry_point() in populate_kprobe_blacklist(), we see the
below errors during bootup:
[ 0.663963] Failed to find blacklist at 7d9b02a648029b6c
[ 0.663970] Failed to find blacklist at a14d03d0394a0001
[ 0.663972] Failed to find blacklist at 7d5302a6f94d0388
[ 0.663973] Failed to find blacklist at 48027d11e8610178
[ 0.663974] Failed to find blacklist at f8010070f8410080
[ 0.663976] Failed to find blacklist at 386100704801f89d
[ 0.663977] Failed to find blacklist at 7d5302a6f94d00b0
Fix this by checking if the function pointer we receive in
ppc_function_entry() already points to kernel text. If so, we just
return it as is. If not, we assume that this is a function descriptor
and proceed to dereference it.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch exports a in-kernel 'library' API which can be called by
other drivers to help interacting with an IBM XSL on a POWER9 system.
The XSL (Translation Service Layer) is a stripped down version of the
PSL (Power Service Layer) used in some cards such as the Mellanox CX5.
Like the PSL, it implements the CAIA architecture, but has a number
of differences, mostly in it's implementation dependent registers.
The XSL also uses a special DMA cxl mode, which uses a slightly
different init sequence for the CAPP and PHB.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch, a few of them are tripping people up while
working on top of next, and we also have a dependency between the CXL
fixes and new CXL code we want to merge into next.
Most of DT files in PowerPC use #include "..." to make pre-processor
include DT in the same directory, but we have 3 exceptional files
that use #include <...> for that.
Fix them to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* pci/host-hv:
PCI: hv: Use vPCI protocol version 1.2
PCI: hv: Add vPCI version protocol negotiation
PCI: hv: Temporary own CPU-number-to-vCPU-number infra
PCI: hv: Use page allocation for hbus structure
PCI: hv: Fix comment formatting and use proper integer fields
* pci/irq-fixups:
arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()
PCI: xilinx-nwl: Move to struct pci_host_bridge IRQ mapping functions
PCI: rockchip: Move to struct pci_host_bridge IRQ mapping functions
PCI: xgene: Move to struct pci_host_bridge IRQ mapping functions
PCI: altera: Drop pci_fixup_irqs()
PCI: versatile: Drop pci_fixup_irqs()
PCI: generic: Drop pci_fixup_irqs()
PCI: faraday: Drop pci_fixup_irqs()
PCI: designware: Drop pci_fixup_irqs()
PCI: iproc: Drop pci_fixup_irqs()
PCI: rcar: Drop pci_fixup_irqs()
PCI: xilinx: Drop pci_fixup_irqs()
PCI: tegra: Drop pci_fixup_irqs()
ARM/PCI: Remove pci_fixup_irqs() call for bios32 host controllers
PCI: Add a call to pci_assign_irq() in pci_device_probe()
OF/PCI: Update of_irq_parse_and_map_pci() comment
PCI: Add pci_assign_irq() function and have pci_fixup_irqs() use it
PCI: Add IRQ mapping function pointers to pci_host_bridge struct
PCI: Build setup-irq.o on all arches
PCI: Remove pci_scan_root_bus_msi()
PCI: xilinx-nwl: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rockchip: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: generic: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xgene: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xilinx: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: altera: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: versatile: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: iproc: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rcar: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: aardvark: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: designware: Convert PCI scan API to pci_scan_root_bus_bridge()
ARM/PCI: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: Make pci_register_host_bridge() PCI core internal
PCI: Add pci_scan_root_bus_bridge() interface
PCI: tegra: Fix host bridge memory leakage
PCI: faraday: Fix host bridge memory leakage
PCI: Add devm_pci_alloc_host_bridge() interface
PCI: Add pci_free_host_bridge() interface
PCI: Initialize bridge release function at bridge allocation
PCI: faraday: Convert IRQ masking to raw PCI config accessors
PCI: iproc: Convert link check to raw PCI config accessors
PCI: xilinx-nwl: Remove nwl_pcie_enable_msi() unused bus parameter
The S500 SoC can start secondary CPUs without busy-looping for pen_release,
so simplify the SMP code compared to the LeMaker kernel tree.
Fixes: 172067e0bc ("ARM: owl: Implement CPU enable-method for S500")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Liu <liuwei@actions-semi.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rely on the fallback to "Generic DT based system".
This change is visible in /proc/cpuinfo.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* pm-sleep:
PM: hibernate: constify attribute_group structures.
PM / hibernate: Drop redundant parameter of swsusp_alloc()
PM / hibernate: Use CONFIG_HAVE_SET_MEMORY for include condition
x86/power/64: Use char arrays for asm function names
* pm-cpufreq:
cpufreq / CPPC: Initialize policy->min to lowest nonlinear performance
cpufreq: sfi: make freq_table static
cpufreq: exynos5440: Fix inconsistent indenting
cpufreq: imx6q: imx6ull should use the same flow as imx6ul
cpufreq: dt: Add support for hi3660
* intel_pstate:
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
intel_pstate: skip scheduler hook when in "performance" mode
intel_pstate: delete scheduler hook in HWP mode
x86: use common aperfmperf_khz_on_cpu() to calculate KHz using APERF/MPERF
cpufreq: intel_pstate: Remove max/min fractions to limit performance
x86: do not use cpufreq_quick_get() for /proc/cpuinfo "cpu MHz"
* pm-cpuidle:
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
x86/ACPI/cstate: Allow ACPI C1 FFH MWAIT use on AMD systems
ARM: cpuidle: Support asymmetric idle definition
* pm-tools:
cpupower: Add support for new AMD family 0x17
cpupower: Fix bug where return value was not used
tools/power turbostat: update version number
tools/power turbostat: decode MSR_IA32_MISC_ENABLE only on Intel
tools/power turbostat: stop migrating, unless '-m'
tools/power turbostat: if --debug, print sampling overhead
tools/power turbostat: hide SKL counters, when not requested
intel_pstate: use updated msr-index.h HWP.EPP values
tools/power x86_energy_perf_policy: support HWP.EPP
x86: msr-index.h: fix shifts to ULL results in HWP macros.
x86: msr-index.h: define HWP.EPP values
x86: msr-index.h: define EPB mid-points
Userspace application can do a hypercall through /dev/xen/privcmd, and
some for some hypercalls argument is a pointers to user-provided
structure. When SMAP is supported and enabled, hypervisor can't access.
So, lets allow it.
The same applies to HYPERVISOR_dm_op, where additionally privcmd driver
carefully verify buffer addresses.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Remove unnecessary variable mfn in function xen_foreach_remap_area() and,
refactor the code.
Variable mfn at line 518:mfn = xen_remap_buf.mfns[i];
is only being used to store a value to be passed as
an argument to the xen_update_mem_tables() function.
This value can be passed directly, which makes variable
mfn unnecessary. Also, value assigned to variable mfn
at line 534:mfn = xen_remap_mfn; is never used.
Addresses-Coverity-ID: 1260110
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the plumbing to disable A/D bits in the MMU based on a new role
bit, ad_disabled. When A/D is disabled, the MMU operates as though A/D
aren't available (i.e., using access tracking faults instead).
To avoid SP -> kvm_mmu_page.role.ad_disabled lookups all over the
place, A/D disablement is now stored in the SPTE. This state is stored
in the SPTE by tweaking the use of SPTE_SPECIAL_MASK for access
tracking. Rather than just setting SPTE_SPECIAL_MASK when an
access-tracking SPTE is non-present, we now always set
SPTE_SPECIAL_MASK for access-tracking SPTEs.
Signed-off-by: Peter Feiner <pfeiner@google.com>
[Use role.ad_disabled even for direct (non-shadow) EPT page tables. Add
documentation and a few MMU_WARN_ONs. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Specify both a mask (i.e., bits to consider) and a value (i.e.,
pattern of bits that indicates a special PTE) for mmio SPTEs. On
Intel, this lets us pack even more information into the
(SPTE_SPECIAL_MASK | EPT_VMX_RWX_MASK) mask we use for access
tracking liberating all (SPTE_SPECIAL_MASK | (non-misconfigured-RWX))
values.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MMU always has hardware A bits or access tracking support, thus
it's unnecessary to handle the scenario where we have neither.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts
pending.
* pci/resource:
PCI: Work around poweroff & suspend-to-RAM issue on Macbook Pro 11
PCI: Do not disregard parent resources starting at 0x0
Conflicts:
arch/x86/pci/fixup.c
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
Update the Hyper-V vPCI driver to use the Server-2016 version of the vPCI
protocol, fixing MSI creation and retargeting issues.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
With the introduction of struct pci_host_bridge.map_irq pointer it is
possible to assign IRQs for all devices originating from a PCI host bridge
at probe time; this is implemented through pci_assign_irq() that relies on
the struct pci_host_bridge.map_irq pointer to map IRQ for a given device.
The benefits this brings are twofold:
- the IRQ for a device is assigned once at probe time
- the IRQ assignment works also for hotplugged devices
With all DT based PCI host bridges converted to the struct
pci_host_bridge.{map/swizzle}_irq hooks mechanism the DT IRQ allocation in
ARM64 pcibios_alloc_irq() is now redundant and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Legacy PCI host controllers (ie host controllers that set-up the PCI bus
through the ARM pci_common_init() API) are currently relying on
pci_fixup_irqs() to assign legacy PCI irqs to devices. This is not ideal
in that pci_fixup_irqs() assigns IRQs for all PCI devices present in a given
system some of which may well be enabled by the time pci_fixup_irqs() is
called (ie a system with multiple host controllers). With the introduction
of struct pci_host_bridge.(*map_irq) pointer it is possible to assign IRQs
for all devices originating from a PCI host bridge at probe time; this is
implemented through pci_assign_irq() that relies on the struct
pci_host_bridge.map_irq pointer to map IRQ for a given device.
The benefits this brings are twofold:
- the IRQ for a device is assigned once at probe time
- the IRQ assignment works also for hotplugged devices
Remove pci_fixup_irqs() call from bios32 code and rely on pci_assign_irq()
to carry out the IRQ mapping at device probe time.
The map_irq() and swizzle_irq() struct pci_host_bridge callbacks are set-up
in the struct pci_host_bridge created in the bios32 pcibios_init_hw()
function and mach-* code paths (for PCI mach implementations that require a
specific struct hw_pci.(*scan) function callback).
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in fixes from Lorenzo:
http://lkml.kernel.org/r/20170701140629.GC8977@red-moon]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
When a process runs out of stack the parisc kernel wrongly faults with SIGBUS
instead of the expected SIGSEGV signal.
This example shows how the kernel faults:
do_page_fault() command='a.out' type=15 address=0xfaac2000 in libc-2.24.so[f8308000+16c000]
trap #15: Data TLB miss fault, vm_start = 0xfa2c2000, vm_end = 0xfaac2000
The vma->vm_end value is the first address which does not belong to the vma, so
adjust the check to include vma->vm_end to the range for which to send the
SIGSEGV signal.
This patch unbreaks building the debian libsigsegv package.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Architectures with a compat syscall table must put compat_sys_keyctl()
in it, not sys_keyctl(). The parisc architecture was not doing this;
fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull MIPS fixes from Ralf Baechle:
"Here's a final round of fixes for 4.12:
- Fix misordered instructions in assembly code making kenel startup
via UHB unreliable.
- Fix special case of MADDF and MADDF emulation.
- Fix alignment issue in address calculation in pm-cps on 64 bit.
- Fix IRQ tracing & lockdep when rescheduling
- Systems with MAARs require post-DMA cache flushes.
The reordering fix and the MADDF/MSUBF fix have sat in linux-next for
a number of days. The others haven't propagated from my pull tree to
linux-next yet but all have survived manual testing and Imagination's
automated test system and there are no pending bug reports"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Avoid accidental raw backtrace
MIPS: Perform post-DMA cache flushes on systems with MAARs
MIPS: Fix IRQ tracing & lockdep when rescheduling
MIPS: pm-cps: Drop manual cache-line alignment of ready_count
MIPS: math-emu: Handle zero accumulator case in MADDF and MSUBF separately
MIPS: head: Reorder instructions missing a delay slot
Pull ARM fix from Russell King:
"One final fix for 4.12 - Doug found a boot failure case triggered by
requesting a non-even MB vmalloc size"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8685/1: ensure memblock-limit is pmd-aligned
On POWER9 SMT8 the 24x7 API returns two result elements for physical core
and virtual CPU events and we need to add their counts to get the final
result.
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 introduces a new version of the hypervisor API to access the 24x7
perf counters. The new version changed some of the structures used for
requests and results.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's an H24x7_DATA_BUFFER_SIZE constant, so use it in init_24x7_request.
There's also an HV_PERF_DOMAIN_MAX constant, so use it in
h_24x7_event_init. This makes the comment above the check redundant,
so remove it.
In add_event_to_24x7_request, a statement is terminated with a comma
instead of a semicolon. Fix it.
In hv-24x7.h, improve comments in struct hv_24x7_result.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The H_GET_24X7_CATALOG_PAGE hcall can return a signed error code, so fix
this in the code.
The H_GET_24X7_DATA hcall can return a signed error code, so fix this in
the code. Also, don't truncate it to 32 bit to use as return value for
make_24x7_request. In case of error h_24x7_event_commit_txn passes that
return value to generic code, so it should be a proper errno. The other
caller of make_24x7_request is single_24x7_request, whose callers don't
actually care which error code is returned so they are not affected by this
change.
Finally, h_24x7_get_value doesn't use the error code from
single_24x7_request, so there's no need to store it.
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
make_24x7_request already calls log_24x7_hcall if it fails, so callers
don't have to do it again.
In fact, since the latter is now only called from the former, there's no
need for a separate log_24x7_hcall anymore so remove it.
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hv-24x7.h has a comment mentioning that result_buffer->results can't be
indexed as a normal array because it may contain results of variable sizes,
so fix the loop in h_24x7_event_commit_txn to take the variation into
account when iterating through results.
Another problem in that loop is that it sets h24x7hw->events[i] to NULL.
This assumes that only the i'th result maps to the i'th request, but that
is not guaranteed to be true. We need to leave the event in the array so
that we don't dereference a NULL pointer in case more than one result maps
to one request.
We still assume that each result has only one result element, so warn if
that assumption is violated.
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
request_buffer can hold 254 requests, so if it already has that number of
entries we can't add a new one.
Also, define constant to show where the number comes from.
Fixes: e3ee15dc5d ("powerpc/perf/hv-24x7: Define add_event_to_24x7_request()")
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
H_GET_24X7_CATALOG_PAGE needs to be passed the version number obtained from
the first catalog page obtained previously. This is a 64 bit number, but
create_events_from_catalog truncates it to 32-bit.
This worked on POWER8, but POWER9 actually uses the upper bits so the call
fails with H_P3 because the hypervisor doesn't recognize the version.
This patch also adds the hcall return code to the error message, which is
helpful when debugging the problem.
Fixes: 5c5cd7b502 ("powerpc/perf/hv-24x7: parse catalog and populate sysfs with events")
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Flip the switch. Running around and screaming "IT'S ALIVE" is optional,
but recommended.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds support for removing bolted (i.e kernel linear mapping) mappings on
powernv. This is needed to support memory hot unplug operations which
are required for the teardown of DAX/PMEM devices.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for the devmap bit on PTEs and PMDs for PPC64 Book3S. This
is used to differentiate device backed memory from transparent huge
pages since they are handled in more or less the same manner by the core
mm code.
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds support to powerpc for the altmap feature of ZONE_DEVICE memory. An
altmap is a driver provided region that is used to provide the backing
storage for the struct pages of ZONE_DEVICE memory. In situations where
large amount of ZONE_DEVICE memory is being added to the system the
altmap reduces pressure on main system memory by allowing the mm/
metadata to be stored on the device itself rather in main memory.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Removes an indentation level and shuffles some code around to make the
following patch cleaner. No functional changes.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently ZONE_DEVICE depends on X86_64 and this will get unwieldly as
new architectures (and platforms) get ZONE_DEVICE support. Move to an
arch selected Kconfig option to save us the trouble.
Cc: linux-mm@kvack.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export it so it can be referenced inside a module.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the different spin loop primitives in some simple powerpc
spin loops, including those which will spin as a common case.
This will help to test the spin loop primitives before more
conversions are done.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add some includes of <linux/processor.h>]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commits 2c0cba482e ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0fe5 ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e64 ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2a5 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"Fixlets for x86:
- Prevent kexec crash when KASLR is enabled, which was caused by an
address calculation bug
- Restore the freeing of PUDs on memory hot remove
- Correct a negated pointer check in the intel uncore performance
monitoring driver
- Plug a memory leak in an error exit path in the RDT code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix memory leak on mount failure
x86/boot/KASLR: Fix kexec crash due to 'virt_addr' calculation bug
x86/boot/KASLR: Add checking for the offset of kernel virtual address randomization
perf/x86/intel/uncore: Fix wrong box pointer check
x86/mm/hotplug: Fix BUG_ON() after hot-remove by not freeing PUD
At present, interrupts are hard-disabled fairly late in the guest
entry path, in the assembly code. Since we check for pending signals
for the vCPU(s) task(s) earlier in the guest entry path, it is
possible for a signal to be delivered before we enter the guest but
not be noticed until after we exit the guest for some other reason.
Similarly, it is possible for the scheduler to request a reschedule
while we are in the guest entry path, and we won't notice until after
we have run the guest, potentially for a whole timeslice.
Furthermore, with a radix guest on POWER9, we can take the interrupt
with the MMU on. In this case we end up leaving interrupts
hard-disabled after the guest exit, and they are likely to stay
hard-disabled until we exit to userspace or context-switch to
another process. This was masking the fact that we were also not
setting the RI (recoverable interrupt) bit in the MSR, meaning
that if we had taken an interrupt, it would have crashed the host
kernel with an unrecoverable interrupt message.
To close these races, we need to check for signals and reschedule
requests after hard-disabling interrupts, and then keep interrupts
hard-disabled until we enter the guest. If there is a signal or a
reschedule request from another CPU, it will send an IPI, which will
cause a guest exit.
This puts the interrupt disabling before we call kvmppc_start_thread()
for all the secondary threads of this core that are going to run vCPUs.
The reason for that is that once we have started the secondary threads
there is no easy way to back out without going through at least part
of the guest entry path. However, kvmppc_start_thread() includes some
code for radix guests which needs to call smp_call_function(), which
must be called with interrupts enabled. To solve this problem, this
patch moves that code into a separate function that is called earlier.
When the guest exit is caused by an external interrupt, a hypervisor
doorbell or a hypervisor maintenance interrupt, we now handle these
using the replay facility. __kvmppc_vcore_entry() now returns the
trap number that caused the exit on this thread, and instead of the
assembly code jumping to the handler entry, we return to C code with
interrupts still hard-disabled and set the irq_happened flag in the
PACA, so that when we do local_irq_enable() the appropriate handler
gets called.
With all this, we now have the interrupt soft-enable flag clear while
we are in the guest. This is useful because code in the real-mode
hypercall handlers that checks whether interrupts are enabled will
now see that they are disabled, which is correct, since interrupts
are hard-disabled in the real-mode code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit b009031f74 ("KVM: PPC: Book3S HV: Take out virtual
core piggybacking code", 2016-09-15), we only have at most one
vcore per subcore. Previously, the fact that there might be more
than one vcore per subcore meant that we had the notion of a
"master vcore", which was the vcore that controlled thread 0 of
the subcore. We also needed a list per subcore in the core_info
struct to record which vcores belonged to each subcore. Now that
there can only be one vcore in the subcore, we can replace the
list with a simple pointer and get rid of the notion of the
master vcore (and in fact treat every vcore as a master vcore).
We can also get rid of the subcore_vm[] field in the core_info
struct since it is never read.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Intel PT:
- Support "ptwrite" instructio, a way to stuff 32 or 64 bit values into
the Intel PT trace (Adrian Hunter)
- Support power events in Intel PT to report changes to C-state (Adrian
Hunter)
- Synthesize Intel PT events as PERF_RECORD_SAMPLE records with a
perf_event_attr.type (PERF_TYPE_SYNTH) just after the range used by the
kernel, i.e. right after what is allocated for PMUs, at INT_MAX + 1U,
attr.config will have the identification for the synthesized event and
the PERF_SAMPLE_RAW payload will have its fields (Adrian Hunter)
Infrastructure:
- Remove warning() and error(), using instead pr_warning() and
pr_error(), consolidating error reporting (Arnaldo Carvalho de Melo)
- Add platform dependency to 'perf test 15' (Thomas Richter)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tvJF
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.13-20170630' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
Intel PT enhancements:
- Support "ptwrite" instruction, a way to stuff 32 or 64 bit values into
the Intel PT trace (Adrian Hunter)
- Support power events in Intel PT to report changes to C-state (Adrian
Hunter)
- Synthesize Intel PT events as PERF_RECORD_SAMPLE records with a
perf_event_attr.type (PERF_TYPE_SYNTH) just after the range used by the
kernel, i.e. right after what is allocated for PMUs, at INT_MAX + 1U,
attr.config will have the identification for the synthesized event and
the PERF_SAMPLE_RAW payload will have its fields (Adrian Hunter)
Infrastructure changes:
- Remove warning() and error(), using instead pr_warning() and
pr_error(), consolidating error reporting (Arnaldo Carvalho de Melo)
- Add platform dependency to 'perf test 15' (Thomas Richter)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the new task struct randomization, we can run into a build
failure for certain random seeds, which will place fields beyond
the allow immediate size in the assembly:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:803: Error: bad immediate value for offset (4096)
Only two constants in asm-offset.h are affected, and I'm changing
both of them here to work correctly in all configurations.
One more macro has the problem, but is currently unused, so this
removes it instead of adding complexity.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[kees: Adjust commit log slightly]
Signed-off-by: Kees Cook <keescook@chromium.org>
Two fixes for code we merged this cycle:
- cxl: Fixes for Coherent Accelerator Interface Architecture 2.0
- Avoid miscompilation w/GCC 4.6.3 on 32-bit - don't inline copy_to/from_user()
Thanks to:
Al Viro, Larry Finger, Christophe Lombard.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Yq9i
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Hopefully the last two powerpc fixes for 4.12.
The CXL one is larger than I'd usually send at rc7, but it fixes new
code this cycle, so better to have it working for the release. It was
actually sent a few weeks back but got blocked in testing behind
another fix that was causing issues.
We are still tracking one crash in v4.12-rc7, but only one person has
reproduced it and the commit identified by bisect doesn't touch any of
the relevant code, so I think it's 50/50 whether that commit is
actually the problem or it's some code layout / toolchain issue.
Two fixes for code we merged this cycle:
- cxl: Fixes for Coherent Accelerator Interface Architecture 2.0
- Avoid miscompilation w/GCC 4.6.3 on 32-bit - don't inline
copy_to/from_user()
Thanks to Al Viro, Larry Finger, Christophe Lombard"
* tag 'powerpc-4.12-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32: Avoid miscompilation w/GCC 4.6.3 - don't inline copy_to/from_user()
cxl: Fixes for Coherent Accelerator Interface Architecture 2.0
Two fixes:
* A fix for AMD IOMMU interrupt remapping code when
IRQs are forwarded directly to KVM guests
* Fixed check in the recently merged code to allow
tboot with Intel VT-d disabled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bw0V
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Two fixes:
- A fix for AMD IOMMU interrupt remapping code when IRQs are
forwarded directly to KVM guests
- Fixed check in the recently merged code to allow tboot with
Intel VT-d disabled"
* tag 'iommu-fixes-v4.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix interrupt remapping when disable guest_mode
iommu/vt-d: Correctly disable Intel IOMMU force on
DMA operations for NOMMU case have been just factored out into
separate compilation unit, so don't keep dead code.
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Andras Szemzo <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now, we have dedicated non-cacheable region for consistent DMA
operations. However, that region can still be marked as bufferable by
MPU, so it'd be safer to have barriers by default. M-class machines
that didn't need it until now also likely won't need it in the future,
therefore, we offer this as an option.
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Andras Szemzo <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
R/M classes of cpus can have memory covered by MPU which in turn might
configure RAM as Normal i.e. bufferable and cacheable. It breaks
dma_alloc_coherent() and friends, since data can stuck in caches now
or be buffered.
This patch factors out DMA support for NOMMU configuration into
separate entity which provides dedicated dma_ops. We have to handle
there several cases:
- configurations with MMU/MPU setup
- configurations without MMU/MPU setup
- special case for M-class, since caches and MPU there are optional
In general we rely on default DMA area for coherent allocations or/and
per-device memory reserves suitable for coherent DMA, so if such
regions are set coherent allocations go from there.
In case MMU/MPU was not setup we fallback to normal page allocator for
DMA memory allocation.
In case we run M-class cpus, for configuration without cache support
(like Cortex-M3/M4) dma operations are forced to be coherent and wired
with dma-noop (such decision is made based on cacheid global
variable); however, if caches are detected there and no DMA coherent
region is given (either default or per-device), dma is disallowed even
MPU is not set - it is because M-class implement system memory map
which defines part of address space as Normal memory.
Reported-by: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Andras Szemzo <sza@esh.hu>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Andras Szemzo <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
[hch: removed the dma_supported() implementation that isn't required anymore]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, internals of dma_common_mmap() is compiled out if build is
done for either NOMMU or target which explicitly says it does not
have/want coherent DMA mmap. It turned out that dma_common_mmap() can
be handy in NOMMU setup (at least for ARM).
This patch converts exitent NOMMU targets to use ARCH_NO_COHERENT_DMA_MMAP,
thus when CONFIG_MMU is gone from dma_common_mmap() their behaviour stays
unchanged.
ARM is not converted to ARCH_NO_COHERENT_DMA_MMAP because it 1)
already has mmap callback which can handle (at some extent) NOMMU 2)
already defines dummy pgprot_noncached() for NOMMU build.
c6x and frv stay untouched since they already have ARCH_NO_COHERENT_DMA_MMAP.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
On an AMD Carrizo laptop, when EHCI runtime PM is enabled, EHCI ports do
not assert PME# for device plug/unplug events while in D3.
As Alan Stern points out [1], the PME signal is not enabled when controller
is in D3, therefore it's not being woken up when new devices get plugged
in.
Testing shows PME signal works when the EHCI power state is D2.
Clear the PCI_PM_CAP_PME_D3 and PCI_PM_CAP_PME_D3cold bits in
dev->pme_support to indicate the device will not assert PME# from those
states.
[1] http://lkml.kernel.org/r/Pine.LNX.4.44L0.1706121010010.2092-100000@iolanthe.rowland.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196091
Link: https://support.amd.com/TechDocs/46837.pdf (Section 23)
Link: https://support.amd.com/TechDocs/42413.pdf (Appendix A2)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
[bhelgaas: changelog, add parens in quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
struct jit_ctx::image is used the store a pointer to the jitted
intructions, which are always little-endian. These instructions
are thus correctly converted from native order to little-endian
before being stored but the pointer 'image' is declared as for
native order values.
Fix this by declaring the field as __le32* instead of u32*.
Same for the pointer used in jit_fill_hole() to initialize
the image.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The macro insn_fetch marks the 'type' argument as having a specified
alignment. Type attributes can only be applied to structs, unions, or
enums, but insn_fetch is only ever invoked with integral types, so Clang
produces 19 -Wignored-attributes warnings for this source file.
Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAllWCM0VHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJECPQ0LrRPXpDjJ0QAI16x6+trKhH31lTSYekYfqm4hZ2
Fp7IbALW9KNCaY35tZov2Zuh99qGRduxTh7ewqhKpON8kkU+UKj0F7zH22+vfN4m
yas/+uNr8R9VLyvea4ysPsgx8Q8v1Ix9setohHYNZIL9/klVqtaHpYvArHVF/mzq
p2j/NxRS2dlp9r2TtoMRMhA05u6r0wolhUuh+z9v2ipib0gfOBIG24jsqCTEcD9n
5A/cVd+ztYshkrV95h3y9peahwt3zOA4QBGzrQ2K25jp0s54nqhmC7JTNSa8dtar
YGW2MuAMoIFTwCFAlpwCzrwpOJFzF3Q6A8bOxei2fjclzjPMgT1xQxuhOoe4ntFa
lTPxSHalm5W6dFTW90YSo2DBcPe+N7sQkhjR0cCeY3GYsOFhXMLTlOl5Pt1YK1or
+3FAI74tFRKvVmb9mhZeGTvuzhDgRvtf3Qq5rjwlGzKc2BBOEgtMyj/Wgwo4N6Dz
IjOnoRaUGELoBCWoTorMxLpsPBdPVSUxNyJTdAhqZ/ZtT1xqjhFNLZcrVWmOTzDM
1cav+jZkla4sLmJSNDD54aCSvvtPHis0nZn9PRlh12xgOyYiAVx4K++MNuWP0P37
hbh1gbPT+FcoVxPurUsX/pjNlTucPZcBwFytZDQlpwtPBpEFzJiImLYe/PldRb0f
9WQOH1Y1+q14MF+N
=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
In preparation for an objtool rewrite which will have broader checks,
whitelist functions and files which cause problems because they do
unusual things with the stack.
These whitelists serve as a TODO list for which functions and files
don't yet have undwarf unwinder coverage. Eventually most of the
whitelists can be removed in favor of manual CFI hint annotations or
objtool improvements.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/7f934a5d707a574bda33ea282e9478e627fb1829.1498659915.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The comment describes the old explicit IPI-based flush logic, which
is long gone.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/55e44997e56086528140c5180f8337dc53fb7ffc.1498751203.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It was historically possible to have two concurrent TLB flushes
targetting the same CPU: one initiated locally and one initiated
remotely. This can now cause an OOPS in leave_mm() at
arch/x86/mm/tlb.c:47:
if (this_cpu_read(cpu_tlbstate.state) == TLBSTATE_OK)
BUG();
with this call trace:
flush_tlb_func_local arch/x86/mm/tlb.c:239 [inline]
flush_tlb_mm_range+0x26d/0x370 arch/x86/mm/tlb.c:317
Without reentrancy, this OOPS is impossible: leave_mm() is only
called if we're not in TLBSTATE_OK, but then we're unexpectedly
in TLBSTATE_OK in leave_mm().
This can be caused by flush_tlb_func_remote() happening between
the two checks and calling leave_mm(), resulting in two consecutive
leave_mm() calls on the same CPU with no intervening switch_mm()
calls.
We never saw this OOPS before because the old leave_mm()
implementation didn't put us back in TLBSTATE_OK, so the assertion
didn't fire.
Nadav noticed the reentrancy issue in a different context, but
neither of us realized that it caused a problem yet.
Reported-by: Levin, Alexander (Sasha Levin) <alexander.levin@verizon.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Nadav Amit <nadav.amit@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: linux-mm@kvack.org
Fixes: 3d28ebceaf ("x86/mm: Rework lazy TLB to track the actual loaded mm")
Link: http://lkml.kernel.org/r/855acf733268d521c9f2e191faee2dcc23a29729.1498751203.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
According to the Intel datasheet, the REP MOVSB instruction
exposes a pretty heavy setup cost (50 ticks), which hurts
short string copy operations.
This change tries to avoid this cost by calling the explicit
loop available in the unrolled code for strings shorter
than 64 bytes.
The 64 bytes cutoff value is arbitrary from the code logic
point of view - it has been selected based on measurements,
as the largest value that still ensures a measurable gain.
Micro benchmarks of the __copy_from_user() function with
lengths in the [0-63] range show this performance gain
(shorter the string, larger the gain):
- in the [55%-4%] range on Intel Xeon(R) CPU E5-2690 v4
- in the [72%-9%] range on Intel Core i7-4810MQ
Other tested CPUs - namely Intel Atom S1260 and AMD Opteron
8216 - show no difference, because they do not expose the
ERMS feature bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4533a1d101fd460f80e21329a34928fad521c1d4.1498744345.git.pabeni@redhat.com
[ Clarified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A few minor clean-ups: constify the lbr_desc[] array and make
local function lbr_from_signext_quirk_rd() static to fix a sparse warning:
"symbol 'lbr_from_signext_quirk_rd' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/20170629091406.9870-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
KASLR uses hack to detect whether we booted via startup_32() or
startup_64(): it checks what is loaded into cr3 and compares it to
_pgtables. _pgtables is the array of page tables where early code
allocates page table from.
KASLR expects cr3 to point to _pgtables if we booted via startup_32(), but
that's not true if we booted with 5-level paging enabled. In this case top
level page table is allocated separately and only the first p4d page table
is allocated from the array.
Let's modify the check to cover both 4- and 5-level paging cases.
The patch also renames 'level4p' to 'top_level_pgt' as it now can hold
page table for 4th or 5th level, depending on configuration.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170628121730.43079-1-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kernel text KASLR is separated into physical address and virtual
address randomization. And for virtual address randomization, we
only randomiza to get an offset between 16M and KERNEL_IMAGE_SIZE.
So the initial value of 'virt_addr' should be LOAD_PHYSICAL_ADDR,
but not the original kernel loading address 'output'.
The bug will cause kernel boot failure if kernel is loaded at a different
position than the address, 16M, which is decided at compiled time.
Kexec/kdump is such practical case.
To fix it, just assign LOAD_PHYSICAL_ADDR to virt_addr as initial
value.
Tested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8391c73 ("x86/KASLR: Randomize virtual address separately")
Link: http://lkml.kernel.org/r/1498567146-11990-3-git-send-email-bhe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For kernel text KASLR, the virtual address is confined to area of 1G,
[0xffffffff80000000, 0xffffffffc0000000). For the implemenataion of
virtual address randomization, we only randomize to get an offset
between 16M and 1G, then add this offset to the starting address,
0xffffffff80000000. Here 16M is the offset which is decided at linking
stage. So the amount of the local variable 'virt_addr' which respresents
the offset plus the kernel output size can not exceed KERNEL_IMAGE_SIZE.
Add a debug check for the offset. If out of bounds, print error
message and hang there.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1498567146-11990-2-git-send-email-bhe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit 81a76d7119 ("MIPS: Avoid using unwind_stack() with
usermode") show_backtrace() invokes the raw backtracer when
cp0_status & ST0_KSU indicates user mode to fix issues on EVA kernels
where user and kernel address spaces overlap.
However this is used by show_stack() which creates its own pt_regs on
the stack and leaves cp0_status uninitialised in most of the code paths.
This results in the non deterministic use of the raw back tracer
depending on the previous stack content.
show_stack() deals exclusively with kernel mode stacks anyway, so
explicitly initialise regs.cp0_status to KSU_KERNEL (i.e. 0) to ensure
we get a useful backtrace.
Fixes: 81a76d7119 ("MIPS: Avoid using unwind_stack() with usermode")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/16656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent CPUs from Imagination Technologies such as the I6400 or P6600 are
able to speculatively fetch data from memory into caches. This means
that if used in a system with non-coherent DMA they require that caches
be invalidated after a device performs DMA, and before the CPU reads the
DMA'd data, in order to ensure that stale values weren't speculatively
prefetched.
Such CPUs also introduced Memory Accessibility Attribute Registers
(MAARs) in order to control the regions in which they are allowed to
speculate. Thus we can use the presence of MAARs as a good indication
that the CPU requires the above cache maintenance. Use the presence of
MAARs to determine the result of cpu_needs_post_dma_flush() in the
default case, in order to handle these recent CPUs correctly.
Note that the return type of cpu_needs_post_dma_flush() is changed to
bool, such that it's clearer what's happening when cpu_has_maar is cast
to bool for the return value. If this patch were backported to a
pre-v4.7 kernel then MIPS_CPU_MAAR was 1ull<<34, so when cast to an int
we would incorrectly return 0. It so happens that MIPS_CPU_MAAR is
currently 1ull<<30, so when truncated to an int gives a non-zero value
anyway, but even so the implicit conversion from long long int to bool
makes it clearer to understand what will happen than the implicit
conversion from long long int to int would. The bool return type also
fits this usage better semantically, so seems like an all-round win.
Thanks to Ed for spotting the issue for pre-v4.7 kernels & suggesting
the return type change.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the scheduler sets TIF_NEED_RESCHED & we call into the scheduler
from arch/mips/kernel/entry.S we disable interrupts. This is true
regardless of whether we reach work_resched from syscall_exit_work,
resume_userspace or by looping after calling schedule(). Although we
disable interrupts in these paths we don't call trace_hardirqs_off()
before calling into C code which may acquire locks, and we therefore
leave lockdep with an inconsistent view of whether interrupts are
disabled or not when CONFIG_PROVE_LOCKING & CONFIG_DEBUG_LOCKDEP are
both enabled.
Without tracing this interrupt state lockdep will print warnings such
as the following once a task returns from a syscall via
syscall_exit_partial with TIF_NEED_RESCHED set:
[ 49.927678] ------------[ cut here ]------------
[ 49.934445] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3687 check_flags.part.41+0x1dc/0x1e8
[ 49.946031] DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
[ 49.946355] CPU: 0 PID: 1 Comm: init Not tainted 4.10.0-00439-gc9fd5d362289-dirty #197
[ 49.963505] Stack : 0000000000000000 ffffffff81bb5d6a 0000000000000006 ffffffff801ce9c4
[ 49.974431] 0000000000000000 0000000000000000 0000000000000000 000000000000004a
[ 49.985300] ffffffff80b7e487 ffffffff80a24498 a8000000ff160000 ffffffff80ede8b8
[ 49.996194] 0000000000000001 0000000000000000 0000000000000000 0000000077c8030c
[ 50.007063] 000000007fd8a510 ffffffff801cd45c 0000000000000000 a8000000ff127c88
[ 50.017945] 0000000000000000 ffffffff801cf928 0000000000000001 ffffffff80a24498
[ 50.028827] 0000000000000000 0000000000000001 0000000000000000 0000000000000000
[ 50.039688] 0000000000000000 a8000000ff127bd0 0000000000000000 ffffffff805509bc
[ 50.050575] 00000000140084e0 0000000000000000 0000000000000000 0000000000040a00
[ 50.061448] 0000000000000000 ffffffff8010e1b0 0000000000000000 ffffffff805509bc
[ 50.072327] ...
[ 50.076087] Call Trace:
[ 50.079869] [<ffffffff8010e1b0>] show_stack+0x80/0xa8
[ 50.086577] [<ffffffff805509bc>] dump_stack+0x10c/0x190
[ 50.093498] [<ffffffff8015dde0>] __warn+0xf0/0x108
[ 50.099889] [<ffffffff8015de34>] warn_slowpath_fmt+0x3c/0x48
[ 50.107241] [<ffffffff801c15b4>] check_flags.part.41+0x1dc/0x1e8
[ 50.114961] [<ffffffff801c239c>] lock_is_held_type+0x8c/0xb0
[ 50.122291] [<ffffffff809461b8>] __schedule+0x8c0/0x10f8
[ 50.129221] [<ffffffff80946a60>] schedule+0x30/0x98
[ 50.135659] [<ffffffff80106278>] work_resched+0x8/0x34
[ 50.142397] ---[ end trace 0cb4f6ef5b99fe21 ]---
[ 50.148405] possible reason: unannotated irqs-off.
[ 50.154600] irq event stamp: 400463
[ 50.159566] hardirqs last enabled at (400463): [<ffffffff8094edc8>] _raw_spin_unlock_irqrestore+0x40/0xa8
[ 50.171981] hardirqs last disabled at (400462): [<ffffffff8094eb98>] _raw_spin_lock_irqsave+0x30/0xb0
[ 50.183897] softirqs last enabled at (400450): [<ffffffff8016580c>] __do_softirq+0x4ac/0x6a8
[ 50.195015] softirqs last disabled at (400425): [<ffffffff80165e78>] irq_exit+0x110/0x128
Fix this by using the TRACE_IRQS_OFF macro to call trace_hardirqs_off()
when CONFIG_TRACE_IRQFLAGS is enabled. This is done before invoking
schedule() following the work_resched label because:
1) Interrupts are disabled regardless of the path we take to reach
work_resched() & schedule().
2) Performing the tracing here avoids the need to do it in paths which
disable interrupts but don't call out to C code before hitting a
path which uses the RESTORE_SOME macro that will call
trace_hardirqs_on() or trace_hardirqs_off() as appropriate.
We call trace_hardirqs_on() using the TRACE_IRQS_ON macro before calling
syscall_trace_leave() for similar reasons, ensuring that lockdep has a
consistent view of state after we re-enable interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/15385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We allocate memory for a ready_count variable per-CPU, which is accessed
via a cached non-coherent TLB mapping to perform synchronisation between
threads within the core using LL/SC instructions. In order to ensure
that the variable is contained within its own data cache line we
allocate 2 lines worth of memory & align the resulting pointer to a line
boundary. This is however unnecessary, since kmalloc is guaranteed to
return memory which is at least cache-line aligned (see
ARCH_DMA_MINALIGN). Stop the redundant manual alignment.
Besides cleaning up the code & avoiding needless work, this has the side
effect of avoiding an arithmetic error found by Bryan on 64 bit systems
due to the 32 bit size of the former dlinesz. This led the ready_count
variable to have its upper 32b cleared erroneously for MIPS64 kernels,
causing problems when ready_count was later used on MIPS64 via cpuidle.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 3179d37ee1 ("MIPS: pm-cps: add PM state entry code for CPS systems")
Reported-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v3.16+
Patchwork: https://patchwork.linux-mips.org/patch/15383/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make thin archives build the default, but keep the config option
to allow exemptions if any breakage can't be quickly solved.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The linker does not like vdso-syms.lds in input archive files.
Make it an extra-y instead.
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The VDSO symbols can't be linked into built-in.o when building with
thin archives, so change this to linking a new object file that is
included into the built-in.o.
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The VDSO symbols can't be linked into built-in.o when building with
thin archives, so change this to linking a new object file that is
included into the built-in.o.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The VDSO symbols can't be linked into built-in.o when building with
thin archives, so change this to linking a new object file that is
included into the built-in.o.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
All the files listed in "extra-y" are generated according to the
dependency. They are still needed in "targets" to include .*.cmd
for incremental building.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Build targets using if_changed(_rule) must depend on FORCE so that
they are evaluated every time.
In order to include .*.cmd files correctly, build targets added to
"targets" must not be prefixed with $(obj)/ because it is done by
scripts/Makefile.lib .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Otherwise, depending upon link order, the branch relocation
limits could be exceeded.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The pmd containing memblock_limit is cleared by prepare_page_table()
which creates the opportunity for early_alloc() to allocate unmapped
memory if memblock_limit is not pmd aligned causing a boot-time hang.
Commit 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
attempted to resolve this problem, but there is a path through the
adjust_lowmem_bounds() routine where if all memory regions start and
end on pmd-aligned addresses the memblock_limit will be set to
arm_lowmem_limit.
Since arm_lowmem_limit can be affected by the vmalloc early parameter,
the value of arm_lowmem_limit may not be pmd-aligned. This commit
corrects this oversight such that memblock_limit is always rounded
down to pmd-alignment.
Fixes: 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
A recent commit moved most logic of early boot up from startup_64() written
in assembly to __startup_64() written in C.
Fengguang reported breakage due to the change. It was tracked down to
CONFIG_FUNCTION_TRACER being enabled.
Tracing this function is not possible because it's invoked from the
earliest boot stage before the relocation fixups have been done. It is the
function doing the relocation.
Exclude it from being built with tracer stubs.
Fixes: c88d71508e ("x86/boot/64: Rewrite startup_64() in C")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: lkp@01.org
Link: http://lkml.kernel.org/r/20170627115948.17938-1-kirill.shutemov@linux.intel.com
Should not init a NULL box. It will cause system crash.
The issue looks like caused by a typo.
This was not noticed because there is no NULL box. Also, for most
boxes, they are enabled by default. The init code is not critical.
Fixes: fff4b87e59 ("perf/x86/intel/uncore: Make package handling more robust")
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170629190926.2456-1-kan.liang@intel.com
Now that compat_vfp_get() uses the regset API to copy the FPSCR
value out to userspace, compat_vfp_set() looks inconsistent. In
particular, compat_vfp_set() will fail if called with kbuf != NULL
&& ubuf == NULL (which is valid usage according to the regset API).
This patch fixes compat_vfp_set() to use user_regset_copyin(),
similarly to compat_vfp_get().
This also squashes a sparse warning triggered by the cast that
drops __user when calling get_user().
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
compat_vfp_set() checks for userspace trying to write an excessive
amount of data to the regset. However this check is conspicuous
for its absence from every other _set() in the arm64 ptrace
implementation. In fact, the core ptrace_regset() already clamps
userspace's iov_len to the regset size before the individual regset
.{get,set}() methods get called.
This patch removes the redundant check.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If get_user() fails when reading the new FPSCR value from userspace
in compat_vfp_get(), then garbage* will be written to the task's
FPSR and FPCR registers.
This patch prevents this by checking the return from get_user()
first.
[*] Actually, zero, due to the behaviour of get_user() on error, but
that's still not what userspace expects.
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PHY used is internal, simply set phy-mode as internal.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the TSC deadline timer is programmed really close to the deadline or
even in the past, the computation in vmx_set_hv_timer will program the
absolute target tsc value to vmcs preemption timer field w/ delta == 0,
then plays a vmentry and an upcoming vmx preemption timer fire vmexit
dance, the lapic timer injection is delayed due to this duration. Actually
the lapic timer which is emulated by hrtimer can handle this correctly.
This patch fixes it by firing the lapic timer and injecting a timer interrupt
immediately during the next vmentry if the TSC deadline timer is programmed
really close to the deadline or even in the past. This saves ~300 cycles on
the tsc_deadline_timer test of apic.flat.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the code to cancel the hv timer into the caller, just before
it starts the hrtimer. Check availability of the hv timer in
start_hv_timer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are many cases in which the hv timer must be canceled. Split out
a new function to avoid duplication.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds SMP code to bring up the remaining S500 CPU cores
by reusing a helper factored out of the SPS power domains driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VNDJ
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-soc+sps-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/soc
Pull "Actions Semi ARM SoC for v4.13 #2" from Andreas Färber:
This adds SMP code to bring up the remaining S500 CPU cores
by reusing a helper factored out of the SPS power domains driver.
* tag 'actions-arm-soc+sps-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: owl: smp: Implement SPS power-gating for CPU2 and CPU3
soc: actions: owl-sps: Factor out owl_sps_set_pg() for power-gating
soc: actions: Add Owl SPS
dt-bindings: power: Add Owl SPS power domains
get_alt_insn() is used to read and create ARM instructions, which
are always stored in memory in little-endian order. These values
are thus correctly converted to/from native order when processed
but the pointers used to hold the address of these instructions
are declared as for native order values.
Fix this by declaring the pointers as __le32* instead of u32* and
make the few appropriate needed changes like removing the unneeded
cast '(u32*)' in front of __ALT_PTR()'s definition.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the flattened device tree format, all integer properties are
in big-endian order.
Here the property "kaslr-seed" is read from the fdt and then
correctly converted to native order (via fdt64_to_cpu()) but the
pointer used for this is not annotated as being for big-endian.
Fix this by declaring the pointer as fdt64_t instead of u64
(fdt64_t being itself typedefed to __be64).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 implementation of ip_fast_csum() do most of the work
in 128 or 64 bit and call csum_fold() to finalize. csum_fold()
itself take a __wsum argument, to insure that this value is
always a 32bit native-order value.
Fix this by adding the sadly needed '__force' to cast the native
'sum' to the type '__wsum'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A wide variety of TI platforms support NAND via the
CONFIG_MTD_NAND_OMAP2 driver (and related BCH options), so enable this.
In addition, multi_v7_defconfig supports the dm8168-evm and that
supports root being on a SATA drive, so build the DM816 AHCI driver into
the resulting kernel as well.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mihail Grigorov <michael.grigorov@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a Kconfig symbol for DTs and drivers being added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8Vxy
-----END PGP SIGNATURE-----
Merge tag 'actions-arm64-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/arm64
Pull "Actions Semi ARM64 SoC for v4.13" from Andreas Färber:
This adds a Kconfig symbol for DTs and drivers being added.
* tag 'actions-arm64-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm64: Prepare Actions Semi S900
This adds an initial DT for the S900 SoC and a devboard based on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZTULJAAoJEPou0S0+fgE/00gP/3V47/jMZmIcRZymiRXUkZAc
cZiIkeKXa0LEXQPk5iTAVXCU7vfhWHHq3g9lA+CWMhbBKO+6K/RwipdscqAxLNfF
kaIIO4M1CEVB9R55JR2jTd6qEHBD+MibTxYc2bbfrWJtbaQJWZ+ep0oKqpOccoby
BRb5yhBt0b0K4GOlgOQHNVIc6sbdhH8ZJ+n/Dqj57eDxzH/u+DUaWdwAIHDaN8Qw
+qAM4HTYSXnlwjWgRgeBws7adDV8wDLbQwpNrmHjDBGxZ8BTIZxrnydKG7AUMIPi
o8A50c7khq4xFQN+IhhNrhwQpilMRjlZc84DwqBsFdaUzei4jYZmY8udxKyuJdhr
ZMerSnvoBOew/KpyvhxaT0aHD0Zlxzl6yKy7dw3FAbqnQTUUmpwp2kM1bsNteMwU
FD5YvLv04R8y9w8XJdsPATQiqu06dZIBZdHubI4D3hWMMYi963eH7KE9ON8mq5Uc
d7Ex1+q9DvjiwOlPtTAcLoeAQeVKeojrDQTTpH4GR3PtukJVBLzS1IiFl1qweele
G1i0WTUgSuYmlvoWOIX4jzeejiXab5WOUszdsIT5qx0LIZKnS/XfQe/kjOYcto6Z
3244hW7AXkdVGOieUX4d+DiizlvJe6VPbq5RJ6Ka5ZmWIdUbH5KkDT4F/jSoi4d4
Ny4hC2twmGfmUIFqbBpp
=WMGS
-----END PGP SIGNATURE-----
Merge tag 'actions-arm64-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt64
Pull "Actions Semi ARM64 based SoC DT for 4.13" from Andreas Färber:
This adds an initial DT for the S900 SoC and a devboard based on it.
* tag 'actions-arm64-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
This adds an initial DT for the S500 SoC and a devboard based on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z5XX
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Pull "Actions Semi ARM based SoC DT for v4.13" from Andreas Färber:
This adds an initial DT for the S500 SoC and a devboard based on it.
* tag 'actions-arm-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
This adds a Kconfig symbol and mach-actions with board and SMP code,
plus a MAINTAINERS entry.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aQiU
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/soc
Pull "Actions Semi ARM SoC for v4.13" from Andreas Färber:
This adds a Kconfig symbol and mach-actions with board and SMP code,
plus a MAINTAINERS entry.
* tag 'actions-arm-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
MAINTAINERS: Update Actions Semi section with SPS
ARM: owl: Implement CPU enable-method for S500
MAINTAINERS: Add Actions Semi Owl section
ARM: Prepare Actions Semi S500
* Enable RPMSG_QCOM_SMD to get boards working again
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wPTI
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/defconfig
Pull "Qualcomm ARM Based defconfig Updates for v4.13 - Part 2" from Andy Gross:
* Enable RPMSG_QCOM_SMD to get boards working again
* tag 'qcom-defconfig-for-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: qcom_defconfig: enable RPMSG_QCOM_SMD
- greatly expands DT clock support for meson8b
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=o8Zj
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Merge "Amlogic 32-bit DT changes for v4.13 (round 2)" from Kevin Hilman:
- greatly expands DT clock support for meson8b
* tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (22 commits)
ARM: dts: meson: use the real ethernet clock on Meson8 and Meson8b
ARM: dts: meson8b: add the SCU device node
ARM: dts: meson: add USB support on Meson8 and Meson8b
ARM: dts: meson: add the hardware random number generator
ARM: dts: meson8: add reserved memory zones
ARM: dts: meson: add the SAR ADC
ARM: dts: meson8: add the pins for the SDIO controller
ARM: dts: meson8: add the PWM_E and PWM_F pins
ARM: dts: meson: use GIC_SPI and IRQ_TYPE_EDGE_RISING macros
ARM: dts: meson: use C preprocessor friendly include syntax
ARM: dts: meson8: fix the IR receiver pins
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
...
Here both variables 'cpu_id' and 'entry_point' are read via
read[lq]_relaxed(), from a little-endian annotated pointer
and then used as a native endian value.
This is correct since the read[lq]() family of function
internally do a little-to-native endian conversion.
But in this case, it is wrong to declare these variable as
little-endian since there are native ones.
Fix this by changing the declaration of these variables
as 'u32' or 'u64' instead of '__le32' / '__le64'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Here the entrypoint, declared as a 64 bit integer, is read from
a pointer to 64bit integer but the read is done via readl_relaxed()
which is for 32bit quantities.
All the high bits will thus be lost which change the meaning
of the test against zero done later.
Fix this by using readq_relaxed() instead as it should be for
64bit quantities.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Here the functions reloc_insn_movw() & reloc_insn_imm() are used
to read, modify and write back ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to/from native order but the pointers used to
hold their addresses are declared as for native order values.
Fix this by declaring the pointers as __le32* and remove the
casts that are now unneeded.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
aarch64_insn_write() is used to write an instruction.
As on ARM64 in-memory instructions are always stored
in little-endian order, this function, taking the instruction
opcode in native order, correctly convert it to little-endian
before sending it to an helper function __aarch64_insn_write()
which will do the effective write.
This is all good, but the variable and argument holding the
converted value are not annotated for a little-endian value
but left for native values.
Fix this by adjusting the prototype of the helper and
directly using the result of cpu_to_le32() without passing
by an intermediate variable (which was not a distinct one
but the same as the one holding the native value).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The function arch64_insn_read() is used to read an instruction.
On AM64 instructions are always stored in little-endian order
and thus the function correctly do a little-to-native endian
conversion to the value just read.
However, the variable used to hold the value before the conversion
is not declared for a little-endian value but for a native one.
Fix this by using the correct type for the declaration: __le32
Note: This only works because the function reading the value,
probe_kernel_read((), takes a void pointer and void pointers
are endian-agnostic. Otherwise probe_kernel_read() should
also be properly annotated (or worse, need to be specialized).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.
Fix this by declaring the intermediate var as __le32 or __le16.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.
Fix this by declaring the intermediate var as __le32 or __le16.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds gettimeofday_fallback() function that wraps assembly
invocation of gettimeofday() syscall using __NR_gettimeofday.
This function is used if pure VDSO implementation gettimeofday()
does not succeed for any reason. Its imeplementation is enclosed in
"#ifdef CONFIG_MIPS_CLOCK_VSYSCALL" to be in sync with the similar
arrangement for __vdso_gettimeofday().
If syscall invocation via __NR_gettimeofday fails, register a3 will
be set. So, after the syscall, register a3 is tested and the return
valuem is negated if it's set.
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16640/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds clock_gettime_fallback() function that wraps assembly
invocation of clock_gettime() syscall using __NR_clock_gettime.
This function is used if pure VDSO implementation of clock_gettime()
does not succeed for any reason. For example, it is called if the
clkid parameter of clock_gettime() is not one of the clkids listed
in the switch-case block of the function __vdso_clock_gettime()
(one such case for clkid is CLOCK_BOOTIME).
If syscall invocation via __NR_clock_gettime fails, register a3 will
be set. So, after the syscall, register a3 is tested and the return
value is negated if it's set.
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix incorrect calculation in do_monotonic() and do_monotonic_coarse()
function that in turn caused incorrect values returned by the vdso
version of system call clock_gettime() on mips64 if its system clock
ID parameter was CLOCK_MONOTONIC or CLOCK_MONOTONIC_COARSE.
Consider these variables and their types on mips32 and mips64:
tk->wall_to_monotonic.tv_sec s64, s64 (kernel/vdso.c)
vdso_data.wall_to_mono_sec u32, u32 (kernel/vdso.c)
to_mono_sec u32, u32 (vdso/gettimeofday.c)
ts->tv_sec s32, s64 (vdso/gettimeofday.c)
For mips64 case, u32 vdso_data.wall_to_mono_sec variable is updated
from the 64-bit signed variable tk->wall_to_monotonic.tv_sec
(kernel/vdso.c:76) which is a negative number holding the time passed
from 1970-01-01 to the time boot started. This 64-bit signed value is
currently around 47+ years, in seconds. For instance, let this value
be:
-1489757461
or
11111111111111111111111111111111 10100111001101000001101011101011
By updating 32-bit vdso_data.wall_to_mono_sec variable, we lose upper
32 bits (signed 1's).
to_mono_sec variable is a parameter of do_monotonic() and
do_monotonic_coarse() functions which holds vdso_data.wall_to_mono_sec
value. Its value needs to be added (or subtracted considering it holds
negative value from the tk->wall_to_monotonic.tv_sec) to the current
time passed from 1970-01-01 (ts->tv_sec), which is again something like
47+ years, but increased by the time passed from the boot to the
current time. ts->tv_sec is 32-bit long in case of 32-bit architecture
and 64-bit long in case of 64-bit architecture. Consider the update of
ts->tv_sec (vdso/gettimeofday.c:55 & 167):
ts->tv_sec += to_mono_sec;
mips32 case: This update will be performed correctly, since both
ts->tv_sec and to_mono_sec are 32-bit long and the sign in to_mono_sec
is preserved. Implicit conversion from u32 to s32 will be done
correctly.
mips64 case: This update will be wrong, since the implicit conversion
will not be done correctly. The reason is that the conversion will be
from u32 to s64. This is because to_mono_sec is 32-bit long for both
mips32 and mips64 cases and s64..33 bits of converted to_mono_sec
variable will be zeros.
So, in order to make MIPS64 implementation work properly for
MONOTONIC and MONOTONIC_COARSE clock ids on mips64, the size of
wall_to_mono_sec variable in mips_vdso_data union and respective
parameters in do_monotonic() and do_monotonic_coarse() functions
should be changed from u32 to u64. Because of consistency, this
size change from u32 and u64 is also done for wall_to_mono_nsec
variable and corresponding function parameters.
As far as similar situations for other architectures are concerned,
let's take a look at arm. Arm has two distinct vdso_data structures
for 32-bit & 64-bit cases, and arm's wall_to_mono_sec and
wall_to_mono_nsec are u32 for 32-bit and u64 for 64-bit cases.
On the other hand, MIPS has only one structure (mips_vdso_data),
hence the need for changing the size of above mentioned parameters.
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: Douglas Leung <douglas.leung@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Petar Jovanovic <petar.jovanovic@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use current_cpu_type() to check for 4Kc processors instead of checking
the PRID directly. This will allow for the 4Kc case to be optimised out
of kernels that can't run on 4KC processors, thanks to __get_cpu_type()
and its unreachable() call.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_MIPS_PGD_C0_CONTEXT, which allows a pointer to the page directory
to be stored in the cop0 Context register when enabled, was previously
only allowed for MIPSr2. MIPSr6 is just as able to make use of it, so
allow it there too.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16204/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In systems where there are multiple actors updating the TLB, the
potential exists for a race condition wherein a CPU hits a TLB exception
but by the time it reaches a TLBP instruction the affected TLB entry may
have been replaced. This can happen if, for example, a CPU shares the
TLB between hardware threads (VPs) within a core and one of them
replaces the entry that another has just taken a TLB exception for.
We handle this race in the case of the Hardware Table Walker (HTW) being
the other actor already, but didn't take into account the potential for
multiple threads racing. Include the code for aborting TLB exception
handling in affected multi-threaded systems, those being the I6400 &
I6500 CPUs which share TLB entries between VPs.
In the case of using RiXi without dedicated exceptions we have never
handled this race even for HTW. This patch adds WARN()s to these cases
which ought never to be hit because all CPUs with either HTW or shared
FTLB RAMs also include dedicated RiXi exceptions, but the WARN()s will
ensure this is always the case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some systems share FTLB RAMs or entries between sibling CPUs (ie.
hardware threads, or VP(E)s, within a core). These properties require
kernel handling in various places. As a start this patch introduces
cpu_has_shared_ftlb_ram & cpu_has_shared_ftlb_entries feature macros
which we set appropriately for I6400 & I6500 CPUs. Further patches will
make use of these macros as appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16202/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On pre-r6 systems with the MT ASE the CPS SMP code included checks to
halt the VPE running mips_cps_boot_vpes() if its bit in the struct
core_boot_config vpe_mask field is clear. This was largely done in order
to allow us to start arbitrary VPEs within a core despite the fact that
hardware is typically configured to run only VPE0 after powering up a
core. VPE0 would start the desired other VPEs, halt itself, and the fact
that VPE0 started would be largely hidden & irrelevant.
In MIPSr6 multithreading we have control over which VPs start executing
when a core powers up via the cores CPC registers accessed remotely
through the redirect block. For this reason the MIPSr6 multithreading
path in mips_cps_boot_vpes() hasn't bothered up until now to handle
halting the VP running it.
However it is possible to power up cores entirely in hardware by using a
pwr_up pin associated with the core. Unfortunately some systems wire
this pin to a logic 1, which means that it is possible for a core to
power up at a point that software doesn't expect. The result is that we
generally go execute the kernel on a CPU that ought not to be running &
the results can be unpredictable.
Handle this case by stopping VPs that we don't expect to be running in
mips_cps_boot_vpes() - with this change even if a core powers up it will
do nothing useful & all VPs within it will stop running before they
proceed to run general kernel code & do any damage. Ideally we would
produce some sort of warning here, but given the stage of core bringup
this happens at that would be non-trivial. We also will only hit this if
a core starts up after being offlined via hotplug, and when that happens
we will already produce a warning that the CPU didn't power down in
cps_cpu_die() which seems sufficient.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16198/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we get into a state where a core that ought to power down isn't doing
so then the current result is that another CPU gets stuck inside
cps_cpu_die() waiting for CPU that ought to be powering down to do so.
The best case scenario is that we then trigger RCU stall messages or
lockup messages, but neither makes it particularly clear what's
happening.
Handle this more gracefully by introducing a timeout beyond which we
warn the user that the core didn't power down & stop waiting for it.
This at least allows the CPU running cps_cpu_die() to continue normally,
and hopefully presuming the CPU that powered back up is doing nothing
harmful the system will continue functioning as normal.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16197/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Systems using the MIPS Coherence Manager (CM) cannot support multi-core
SMP with dcache aliasing. This is because CPU caches are VIPT, but
interventions in CM-based systems provide only the physical address to
remote caches. This means that interventions may behave incorrectly in
the presence of an aliasing dcache, since the physical address used
when handling an intervention may lead to operation on an aliased cache
line rather than the correct line.
Prevent us from running into this issue by refusing to boot secondary
cores in systems where dcache aliasing may occur.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16196/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prior to MIPSr6 multithreading is only supported if CONFIG_MIPS_MT_SMP
is enabled, so CONFIG_MIPS_MT_SMP selects CONFIG_SYS_SUPPORTS_SCHED_SMT.
With MIPSr6 the CONFIG_MIPS_CPS SMP implementation always supports
multithreading, so have it select CONFIG_SYS_SUPPORTS_SCHED_SMT in order
to allow the scheduler to make better informed decisions on
multithreaded MIPSr6 systems (for example those using I6400 or I6500
CPUs).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16195/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than using BUG_ON in the case of an invalid attempt to lock
access to a non-zero VP on a pre-CM3 system, use WARN_ON so that we have
even the slightest chance of recovery.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16194/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CM3 provides a GCR_CL_OTHER register per VP, rather than only per core.
This means that we don't need to prevent other VPs within a core from
racing with code that makes use of the core-other register region.
Reduce locking overhead by demoting the per-core spinlock providing
protection for CM2.5 & lower to a per-CPU/per-VP spinlock for CM3 &
higher.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16193/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we're running on a system with only 1 possible CPU then it makes no
sense to reserve or initialise IPIs since we'll never use them. Avoid
doing so.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16192/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reduce the log level for branch emulation error messages issued before
sending SIGILL by `__compute_return_epc_for_insn' as these are triggered
by user software and are not an event that would normally require any
attention. The same signal sent from elsewhere does not actually leave
any trace in the kernel log at all.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16402/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update commit 1ac944007b ("MIPS: math-emu: Add mfhc1 & mthc1
support.") and like done throughout `cop1Emulate' for other cases also
for the MFHC1 and MTHC1 instructions return SIGILL right away rather
than jumping to a single `return' statement.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16401/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a user-visible message, so we want it to be spelled correctly.
Fixes: 5f9f41c474 ("MIPS: kernel: Prepare the JR instruction for emulation on MIPS R6")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.19+
Patchwork: https://patchwork.linux-mips.org/patch/16400/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix:
* commit 8467ca0122 ("MIPS: Emulate the new MIPS R6 branch compact
(BC) instruction"),
* commit 84fef63012 ("MIPS: Emulate the new MIPS R6 BALC
instruction"),
* commit 69b9a2fd05 ("MIPS: Emulate the new MIPS R6 BEQZC and JIC
instructions"),
* commit 28d6f93d20 ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC
instructions"),
* commit c893ce38b2 ("MIPS: Emulate the new MIPS R6 BOVC, BEQC and
BEQZALC instructions")
and send SIGILL rather than returning -SIGILL for R6 branch and jump
instructions. Returning -SIGILL is never correct as the API defines
this function's result upon error to be -EFAULT and a signal actually
issued.
Fixes: 8467ca0122 ("MIPS: Emulate the new MIPS R6 branch compact (BC) instruction")
Fixes: 84fef63012 ("MIPS: Emulate the new MIPS R6 BALC instruction")
Fixes: 69b9a2fd05 ("MIPS: Emulate the new MIPS R6 BEQZC and JIC instructions")
Fixes: 28d6f93d20 ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions")
Fixes: c893ce38b2 ("MIPS: Emulate the new MIPS R6 BOVC, BEQC and BEQZALC instructions")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.19+
Patchwork: https://patchwork.linux-mips.org/patch/16399/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix commit 319824eabc ("MIPS: kernel: branch: Do not emulate the
branch likelies on MIPS R6") and also send SIGILL rather than returning
-SIGILL for BLTZAL, BLTZALL, BGEZAL and BGEZALL instruction encodings no
longer supported in R6, except where emulated. Returning -SIGILL is
never correct as the API defines this function's result upon error to be
-EFAULT and a signal actually issued.
Fixes: 319824eabc ("MIPS: kernel: branch: Do not emulate the branch likelies on MIPS R6")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.19+
Patchwork: https://patchwork.linux-mips.org/patch/16398/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the more accurate `sigill_r2r6' name for the label used in the case
of sending SIGILL in the absence of the instruction emulator for an
earlier ISA level instruction that has been removed as from the R6 ISA,
so that the `sigill_r6' name is freed for the situation where an R6
instruction is not supposed to be interpreted, because the executing
processor does not support the R6 ISA.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.19+
Patchwork: https://patchwork.linux-mips.org/patch/16397/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix commit e50c0a8fa6 ("Support the MIPS32 / MIPS64 DSP ASE.") and
send SIGILL rather than SIGBUS whenever an unimplemented BPOSGE32 DSP
ASE instruction has been encountered in `__compute_return_epc_for_insn'
as our Reserved Instruction exception handler would in response to an
attempt to actually execute the instruction. Sending SIGBUS only makes
sense for the unaligned PC case, since moved to `__compute_return_epc'.
Adjust function documentation accordingly, correct formatting and use
`pr_info' rather than `printk' as the other exit path already does.
Fixes: e50c0a8fa6 ("Support the MIPS32 / MIPS64 DSP ASE.")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 2.6.14+
Patchwork: https://patchwork.linux-mips.org/patch/16396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a regression introduced with commit fb6883e580 ("MIPS: microMIPS:
Support handling of delay slots.") and defer to `__compute_return_epc'
if the ISA bit is set in EPC with non-MIPS16, non-microMIPS hardware,
which will then arrange for a SIGBUS due to an unaligned instruction
reference. Returning EPC here is never correct as the API defines this
function's result to be either a negative error code on failure or one
of 0 and BRANCH_LIKELY_TAKEN on success.
Fixes: fb6883e580 ("MIPS: microMIPS: Support handling of delay slots.")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.9+
Patchwork: https://patchwork.linux-mips.org/patch/16395/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit fb6883e580 ("MIPS: microMIPS: Support handling of
delay slots.") and actually decode the regular MIPS JALX major
instruction opcode, the handling of which has been added with the said
commit for EPC calculation in `__compute_return_epc_for_insn'.
Fixes: fb6883e580 ("MIPS: microMIPS: Support handling of delay slots.")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.9+
Patchwork: https://patchwork.linux-mips.org/patch/16394/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Terminate FPU emulation immediately whenever an ISA mode switch has been
observed. This is so that we do not interpret machine code in the wrong
mode, for example when a regular MIPS FPU instruction has been placed in
a delay slot of a jump that switches into the MIPS16 mode, as with the
following code (taken from a GCC test suite case):
00400650 <set_fast_math>:
400650: 3c020100 lui v0,0x100
400654: 03e00008 jr ra
400658: 44c2f800 ctc1 v0,c1_fcsr
40065c: 00000000 nop
[...]
004012d0 <__libc_csu_init>:
4012d0: f000 6a02 li v0,2
4012d4: f150 0b1c la v1,3f9430 <_DYNAMIC-0x6df0>
4012d8: f400 3240 sll v0,16
4012dc: e269 addu v0,v1
4012de: 659a move gp,v0
4012e0: f00c 64f6 save a0-a2,48,ra,s0-s1
4012e4: 673c move s1,gp
4012e6: f010 9978 lw v1,-32744(s1)
4012ea: d204 sw v0,16(sp)
4012ec: eb40 jalr v1
4012ee: 653b move t9,v1
4012f0: f010 997c lw v1,-32740(s1)
4012f4: f030 9920 lw s1,-32736(s1)
4012f8: e32f subu v1,s1
4012fa: 326b sra v0,v1,2
4012fc: d206 sw v0,24(sp)
4012fe: 220c beqz v0,401318 <__libc_csu_init+0x48>
401300: 6800 li s0,0
401302: 99e0 lw a3,0(s1)
401304: 4801 addiu s0,1
401306: 960e lw a2,56(sp)
401308: 4904 addiu s1,4
40130a: 950d lw a1,52(sp)
40130c: 940c lw a0,48(sp)
40130e: ef40 jalr a3
401310: 653f move t9,a3
401312: 9206 lw v0,24(sp)
401314: ea0a cmp v0,s0
401316: 61f5 btnez 401302 <__libc_csu_init+0x32>
401318: 6476 restore 48,ra,s0-s1
40131a: e8a0 jrc ra
Here `set_fast_math' is called from `40130e' (`40130f' with the ISA bit)
and emulation triggers for the CTC1 instruction. As it is in a jump
delay slot emulation continues from `401312' (`401313' with the ISA
bit). However we have no path to handle MIPS16 FPU code emulation,
because there are no MIPS16 FPU instructions. So the default emulation
path is taken, interpreting a 32-bit word fetched by `get_user' from
`401313' as a regular MIPS instruction, which is:
401313: f5ea0a92 sdc1 $f10,2706(t7)
This makes the FPU emulator proceed with the supposed SDC1 instruction
and consequently makes the program considered here terminate with
SIGSEGV.
A similar although less severe issue exists with pure-microMIPS
processors in the case where similarly an FPU instruction is emulated in
a delay slot of a register jump that (incorrectly) switches into the
regular MIPS mode. A subsequent instruction fetch from the jump's
target is supposed to cause an Address Error exception, however instead
we proceed with regular MIPS FPU emulation.
For simplicity then, always terminate the emulation loop whenever a mode
change is detected, denoted by an ISA mode bit flip. As from commit
377cb1b6c1 ("MIPS: Disable MIPS16/microMIPS crap for platforms not
supporting these ASEs.") the result of `get_isa16_mode' can be hardcoded
to 0, so we need to examine the ISA mode bit by hand.
This complements commit 102cedc32a ("MIPS: microMIPS: Floating point
support.") which added JALX decoding to FPU emulation.
Fixes: 102cedc32a ("MIPS: microMIPS: Floating point support.")
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.9+
Patchwork: https://patchwork.linux-mips.org/patch/16393/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch switches MIPS to make use of generically implemented queued
spinlocks, rather than the ticket spinlocks used previously. This allows
us to drop a whole load of inline assembly, share more generic code, and
is also a performance win.
Results from running the AIM7 short workload on a MIPS Creator Ci40 (ie.
2 core 2 thread interAptiv CPU clocked at 546MHz) with v4.12-rc4
pistachio_defconfig, with ftrace disabled due to a current bug, and both
with & without use of queued rwlocks & spinlocks:
Forks | v4.12-rc4 | +qlocks | Change
-------|-----------|----------|--------
10 | 52630.32 | 53316.31 | +1.01%
20 | 51777.80 | 52623.15 | +1.02%
30 | 51645.92 | 52517.26 | +1.02%
40 | 51634.88 | 52419.89 | +1.02%
50 | 51506.75 | 52307.81 | +1.02%
60 | 51500.74 | 52322.72 | +1.02%
70 | 51434.81 | 52288.60 | +1.02%
80 | 51423.22 | 52434.85 | +1.02%
90 | 51428.65 | 52410.10 | +1.02%
The kernels used for these tests also had my "MIPS: Hardcode cpu_has_*
where known at compile time due to ISA" patch applied, which allows the
kernel_uses_llsc checks in cmpxchg() & xchg() to be optimised away at
compile time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch switches MIPS to make use of generically implemented queued
read/write locks, rather than the custom implementation used previously.
This allows us to drop a whole load of inline assembly, share more
generic code, and is also a performance win.
Results from running the AIM7 short workload on a MIPS Creator Ci40 (ie.
2 core 2 thread interAptiv CPU clocked at 546MHz) with v4.12-rc4
pistachio_defconfig, with ftrace disabled due to a current bug, and both
with & without use of queued rwlocks & spinlocks:
Forks | v4.12-rc4 | +qlocks | Change
-------|-----------|----------|--------
10 | 52630.32 | 53316.31 | +1.01%
20 | 51777.80 | 52623.15 | +1.02%
30 | 51645.92 | 52517.26 | +1.02%
40 | 51634.88 | 52419.89 | +1.02%
50 | 51506.75 | 52307.81 | +1.02%
60 | 51500.74 | 52322.72 | +1.02%
70 | 51434.81 | 52288.60 | +1.02%
80 | 51423.22 | 52434.85 | +1.02%
90 | 51428.65 | 52410.10 | +1.02%
The kernels used for these tests also had my "MIPS: Hardcode cpu_has_*
where known at compile time due to ISA" patch applied, which allows the
kernel_uses_llsc checks in cmpxchg() & xchg() to be optimised away at
compile time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __xchg() function declares its first 2 arguments in reverse order
compared to the xchg() macro, which is confusing & serves no purpose.
Reorder the arguments such that __xchg() & xchg() match.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement support for 1 & 2 byte cmpxchg() using read-modify-write atop
a 4 byte cmpxchg(). This allows us to support these atomic operations
despite the MIPS ISA only providing 4 & 8 byte atomic operations.
This is required in order to support queued rwlocks (qrwlock) in a later
patch, since these make use of a 1 byte cmpxchg() in their slow path.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement 1 & 2 byte xchg() using read-modify-write atop a 4 byte
cmpxchg(). This allows us to support these atomic operations despite the
MIPS ISA only providing for 4 & 8 byte atomic operations.
This is required in order to support queued spinlocks (qspinlock) in a
later patch, since these make use of a 2 byte xchg() in their slow path.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the macro definition of __cmpxchg() with an inline function,
which is easier to read & modify. The cmpxchg() & cmpxchg_local() macros
are adjusted to call the new __cmpxchg() function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __xchg_u32() & __xchg_u64() functions now add very little value.
This patch therefore removes them, by:
- Moving memory barriers out of them & into xchg(), which also removes
the duplication & readies us to support xchg_relaxed() if we wish to.
- Calling __xchg_asm() directly from __xchg().
- Performing the check for CONFIG_64BIT being enabled in the size=8
case of __xchg().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
xchg() has up until now simply returned the x parameter in cases where
it is called with a pointer to a value of an unsupported size. This will
often cause the calling code to hit a failure path, presuming that the
value of x differs from the content of the memory pointed at by ptr, but
we can do better by producing a compile-time or link-time error such
that unsupported calls to xchg() are detectable earlier than runtime.
This patch does this in the same was as is already done for cmpxchg(),
using a call to a missing function annotated with __compiletime_error().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Our cmpxchg() implementation relies upon generating a call to a function
which doesn't really exist (__cmpxchg_called_with_bad_pointer) to create
a link failure in cases where cmpxchg() is called with a pointer to a
value of an unsupported size.
The __compiletime_error macro can be used to decorate a function such
that a call to it generates a compile-time, rather than a link-time,
error. This patch uses __compiletime_error to cause bad cmpxchg() calls
to error out at compile time rather than link time, allowing errors to
occur more quickly & making it easier to spot where the problem comes
from.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a macro to generate the 32 & 64 bit variants of the backing code for
xchg(), much as is already done for cmpxchg(). This removes the
duplication that could previously be found in __xchg_u32() &
__xchg_u64().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prior to this patch the xchg & cmpxchg functions have duplicated code
which is for all intents & purposes identical apart from use of a
branch-likely instruction in the R10000_LLSC_WAR case & a regular branch
instruction in the non-R10000_LLSC_WAR case.
This patch removes the duplication, declaring a __scbeqz macro to select
the branch instruction suitable for use when checking the result of an
sc instruction & making use of it to unify the 2 cases.
In __xchg_u{32,64}() this means writing the branch in asm, where it was
previously being done in C as a do...while loop for the
non-R10000_LLSC_WAR case. As this is a single instruction, and adds
consistency with the R10000_LLSC_WAR cases & the cmpxchg() code, this
seems worthwhile.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disable usage of PREF instruction usage by memcpy for MIPS R6.
MIPS R6 redefines PREF instruction with smaller offset than
ordinary MIPS. However, the memcpy code uses PREF instruction
with offsets bigger than +-256 bytes.
Malta kernels already disable usage of PREF for memcpy.
This was found during adaptation of MIPS R6 for virtual board
used by Android emulator.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtech.com>
Cc: James.Hogan@imgtec.com
Cc: Paul.Burton@imgtec.com
Cc: Raghu.Gandham@imgtec.com
Cc: Leonid.Yegoshin@imgtec.com
Cc: Douglas.Leung@imgtec.com
Cc: Petar.Jovanovic@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16510/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add "-modd-spreg" when compiling the kernel for mips32r6 target.
This makes sure the kernel builds properly even with toolchains that
use "-mno-odd-spreg" by default. This is the case with Android gcc.
Prior to this patch, kernel builds using gcc for Android failed with
following error messages, if target architecture is set to mips32r6:
arch/mips/kernel/r4k_switch.S: Assembler messages:
.../r4k_switch.S:210: Error: float register should be even, was 1
.../r4k_switch.S:212: Error: float register should be even, was 3
.../r4k_switch.S:214: Error: float register should be even, was 5
.../r4k_switch.S:216: Error: float register should be even, was 7
.../r4k_switch.S:218: Error: float register should be even, was 9
.../r4k_switch.S:220: Error: float register should be even, was 11
.../r4k_switch.S:222: Error: float register should be even, was 13
.../r4k_switch.S:224: Error: float register should be even, was 15
.../r4k_switch.S:226: Error: float register should be even, was 17
.../r4k_switch.S:228: Error: float register should be even, was 19
.../r4k_switch.S:230: Error: float register should be even, was 21
.../r4k_switch.S:232: Error: float register should be even, was 23
.../r4k_switch.S:234: Error: float register should be even, was 25
.../r4k_switch.S:236: Error: float register should be even, was 27
.../r4k_switch.S:238: Error: float register should be even, was 29
.../r4k_switch.S:240: Error: float register should be even, was 31
make[2]: *** [arch/mips/kernel/r4k_switch.o] Error 1
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: James.Hogan@imgtec.com
Cc: Paul.Burton@imgtec.com
Cc: Raghu.Gandham@imgtec.com
Cc: Leonid.Yegoshin@imgtec.com
Cc: Douglas.Leung@imgtec.com
Cc: Petar.Jovanovic@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement support for parsing 'memmap' kernel command line parameter.
This patch covers parsing of the following two formats for 'memmap'
parameter values:
- nn[KMG]@ss[KMG]
- nn[KMG]$ss[KMG]
([KMG] = K M or G (kilo, mega, giga))
These two allowed formats for parameter value are already documented
in file kernel-parameters.txt in Documentation/admin-guide folder.
Some architectures already support them, but Mips did not prior to
this patch.
Excerpt from Documentation/admin-guide/kernel-parameters.txt:
memmap=nn[KMG]@ss[KMG]
[KNL] Force usage of a specific region of memory.
Region of memory to be used is from ss to ss+nn.
memmap=nn[KMG]$ss[KMG]
Mark specific memory as reserved.
Region of memory to be reserved is from ss to ss+nn.
Example: Exclude memory from 0x18690000-0x1869ffff
memmap=64K$0x18690000
or
memmap=0x10000$0x18690000
There is no need to update this documentation file with respect to
this patch.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Cc: James.Hogan@imgtec.com
Cc: Paul.Burton@imgtec.com
Cc: Raghu.Gandham@imgtec.com
Cc: Leonid.Yegoshin@imgtec.com
Cc: Douglas.Leung@imgtec.com
Cc: Petar.Jovanovic@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16508/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sort enum loongson_cpu_type in a more reasonable manner, this makes the
CPU names more clear and extensible. Those already defined enum values
are renamed to Legacy_* for compatibility.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With this patch we can set irq affinity via procfs, so as to improve
network performance.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16590/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The only user of thread_saved_pc() in non-arch-specific code was removed
in commit 8243d55977 ("sched/core: Remove pointless printout in
sched_show_task()"). Remove the implementations as well.
Some architectures use thread_saved_pc() in their arch-specific code.
Leave their thread_saved_pc() intact.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neither soft poweroff (transition to ACPI power state S5) nor
suspend-to-RAM (transition to state S3) works on the Macbook Pro 11,4 and
11,5.
The problem is related to the [mem 0x7fa00000-0x7fbfffff] space. When we
use that space, e.g., by assigning it to the 00:1c.0 Root Port, the ACPI
Power Management 1 Control Register (PM1_CNT) at [io 0x1804] doesn't work
anymore.
Linux does a soft poweroff (transition to S5) by writing to PM1_CNT. The
theory about why this doesn't work is:
- The write to PM1_CNT causes an SMI
- The BIOS SMI handler depends on something in
[mem 0x7fa00000-0x7fbfffff]
- When Linux assigns [mem 0x7fa00000-0x7fbfffff] to the 00:1c.0 Port, it
covers up whatever the SMI handler uses, so the SMI handler no longer
works correctly
Reserve the [mem 0x7fa00000-0x7fbfffff] space so we don't assign it to
anything.
This is voodoo programming, since we don't know what the real conflict is,
but we've failed to find the root cause.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=103211
Tested-by: thejoe@gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Chen Yu <yu.c.chen@intel.com>
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups
- fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iQIcBAABAgAGBQJZU5JdAAoJEBF7vIC1phx8gCwP/RTl1DzLsyuSbX/AhneQVb/X
gXRnrtVEMsya4vL5lZxbp8JD5J4nBu8vNlgDmQwXM1KiFVDW5IFyQLUHv5PP899z
357mQC61pbkuDA8BhM71FuQav2V0ZMes+FYsza4Zx+Iev4uQtVfTos/nuMPnRVaD
hSfWKbQ9dH/Yluxn8ClXkUOrLH7luiU7HZoQLTxYPFmyM9BIgSbUH2rSXUbQ/i5I
PLpcky6M52/A/IFeEAt5qASsCwWJhPSLGsLKghDKvHDcBWVSb/M94ypXKInZ0pTf
l97TOwCHVODje0Nn4R7wuoeY1ahOwgfhbI3R8m9Cnck3t7mbWtzYVn3DvSXl/Juk
3dfMkbi/GG9lrHoOwnGVGUsaNw5U11sDZEV+rVDT5847HEnGclNWfIBzr4Lcchdr
7f3qap9AGLWu79e32mOP2yO2zFKXpDdVuFfW/c/ms4wq3v03a6HxcUkIn98m6Q1O
EEKzwknA1tSCdtWKOW9THENmywd1o4pMisC+FHnBxFwllOl5ORpbPegOrPCe7qQW
+MZClAJl0s23NpbEMzwrilHzC1P9RxYTFnhGmVamcAg9PVOcFIOGllum26IXzaFM
SyJ8HxS10SiAIVzv18yw3uxy6BUzzuKulIPu+W7JeOTOAAWiwTNL8wEx1ol93Ioi
531QgI7kPfDnudS14WaM
=L7Ia
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: fixes and features for 4.13
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups
- fixes
The memory operand fetched for INVVPID is 128 bits. Bits 63:16 are
reserved and must be zero. Otherwise, the instruction fails with
VMfail(Invalid operand to INVEPT/INVVPID). If the INVVPID_TYPE is 0
(individual address invalidation), then bits 127:64 must be in
canonical form, or the instruction fails with VMfail(Invalid operand
to INVEPT/INVVPID).
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All x86 PCI configuration space accessors have either their own
serialization or can operate completely lockless (ECAM).
Disable the global lock in the generic PCI configuration space accessors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.295079391@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 wants to get rid of the global pci_lock protecting the config space
accessors so ECAM mode can operate completely lockless, but the CE4100 PCI
code relies on that to protect the simulation registers.
Restructure the code so it uses the x86 specific pci_config_lock to
serialize the inner workings of the CE4100 PCI magic. That allows to remove
the global locking via pci_lock later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.126873574@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the legacy PCI init fails, then there are no PCI config space accesors
available, but the code continues and tries to scan the busses, which fails
due to the lack of config space accessors.
Return right away, if the last init fallback fails.
Switch the few printks to pr_info while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215057.047576516@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For some historic reason these defines are duplicated and also available in
arch/x86/include/asm/pci_x86.h,
Remove them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170316215056.967808646@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert ARM bios32 code to pci_scan_root_bus_bridge() to improve the PCI
root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fold in warning fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-1-arnd@arndb.de]
[bhelgaas: set bridge->ops for mv78xx0]
[bhelgaas: fold in fixes from Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>:
http://lkml.kernel.org/r/20170701135457.GB8977@red-moon]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Many subsystems will not use refcount_t unless there is a way to build the
kernel so that there is no regression in speed compared to atomic_t. This
adds CONFIG_REFCOUNT_FULL to enable the full refcount_t implementation
which has the validation but is slightly slower. When not enabled,
refcount_t uses the basic unchecked atomic_t routines, which results in
no code changes compared to just using atomic_t directly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Windsor <dwindsor@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Hans Liljestrand <ishkamiel@gmail.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Jann Horn <jannh@google.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arozansk@redhat.com
Cc: axboe@kernel.dk
Cc: linux-arch <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170621200026.GA115679@beast
Signed-off-by: Ingo Molnar <mingo@kernel.org>
