When commit 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module
device node") was posted upstream no clocks were specified. However,
when the pack was picked into the Chrome OS kernel tree (allegedly
directly from the mailing list post) it had clock properties.
I presume that the clock should be there, so let's add it.
Fixes: 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module device node")
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add also the required iommus property]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The USB controllers need to be associated with their respective IOMMU
bank, so define this on the dwc3 nodes.
Also add dma-ranges to the qcom-dwc3 nodes to make the bus' DMA mask
propagate to the dwc3 controller instances.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With apps_smmu initializing the SMMU we must specify iommus property for
the sdhc controller.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since all cpus in the big and little clusters, respectively, are in the
same frequency domain, use all of them for mitigation in the
cooling-map. We end up with two cooling devices - one each for the big
and little clusters.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The apcs node has #clock-cells = <0>, which means that those who
references it should specify 0 arguments.
The apcs reference in the cpu node incorrectly specifies an argument,
remove this bogus argument.
Fixes: 65afdf4583 ("arm64: dts: qcom: msm8916: Add CPU frequency scaling support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the rpm clock controller node, to provide the low-noise baseband
clock for the USB PHYs, among other things.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add nodes for USB and related PHYs.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Define all six QUP controllers, both as SPI and I2C, allowing boards to
enable these as needed. Associated pinmux states are also defined, to
require only pinconf states to be specified by the boards, as they are
enabled.
Note that SPI has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the BLSP2 BAM and add the remaining four UARTs found on the QCS404
platform.
Note that these has not been tested.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
BLSP1 UART2 is used as debug uart on the EVB development board, define
pinmux state for the UART in the platform dtsi and pinconf state for it
in the board dts.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fix up the lpasscc address and size, missed during the conversion to
address- and size-cells of 2.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the duplicate inclusion of qcom,gcc-sdm845.h
mistakenly introduced by commit 6e17f81405 ("arm64:
dts: sdm845: add prng-ee node").
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
[bjorn: Also fix sort order of lpasscc include, while we're there]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add reserve-memory nodes for mpss and mba required for
remoteproc mss pil.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the gpio-ranges property to the TLMM node so that GPIO hogs work.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
For devices attached to an IOMMU, translation between IOVA and physical
addresses is no longer 1:1 and dma-ranges should be specified to
describe the available IOVA address space.
On SDM845 the busses are implemented with 36 address bits, so dma-ranges
must be defined to reduce the size of the IOVA address space from the 48
bits supported by the SMMU. Without this DMA allocations may end up with
IOVAs outside the valid range, that gets truncated by the bus between
the device and its translation unit.
Also extend ranges to describe the available address space.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The busses on SDM845 provides 36 address bits, extend the address and
size cells to make it possible to describe this in "ranges" and
"dma-ranges".
While touching all reg properties, addresses are padded to 8 digits.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on SDM845 soc.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the node to support PDC Global reset driver on
SDM845 SoCs
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Correct address for pcs_misc register region of USB3 QMP UNI PHY.
These registers are used during runtime-suspend/resume routines
of phy.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: ca4db2b538 ("arm64: dts: qcom: sdm845: Add USB-related nodes")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the low pass audio clock controller node to sdm845 based on
the example in the bindings.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[bjorn: Disabled lpasscc node, as it's normally protected]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the video clock controller node to sdm845 based on the examples
in the bindings.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the GPU clock controller nodes as per the example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Quad SPI controller to the main sdm845 device tree file.
Boards will be expected to assign the proper pinctrl depending on how
many chip selects they have hooked up and how many data lines.
This depends on commit 48735597f7 ("clk: qcom: Add qspi (Quad SPI)
clock defines for sdm845 to header") to add the needed defines. It
also shouldn't land until the patch ("dt-bindings: spi: Qualcomm Quad
SPI(QSPI) documentation") [1] lands.
[1] https://lkml.kernel.org/r/20181002214709.162330-1-ryandcase@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
msm8998 has a dozen i2c controllers which can be used to connect to board
specific peripherals. Enumerate the controllers so that boards can wire
up as needed.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[bjorn: Renumbered labels on BLSP2 nodes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
l21 is used as sdcard vmmc, and needs the load increased to prevent
voltage drop issues with some sdcards. This addresses -84 errors seen
during sdcard init with SDR104 cards.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DPU is short for the Display Processing Unit. It is the display
controller on Qualcomm SDM845 chips.
This change adds MDSS and DSI nodes to enable display on the
target device.
Changes in v2:
- Beefed up commit message
- Use SoC specific compatibles for mdss and dpu (Rob H)
- Use assigned-clocks to set initial clock frequency(Rob H)
Changes in v3:
- added IOMMU node
- Fix device naming (remove _phys)
- Use correct IRQ_TYPE in interrupt specifiers
Changes in v4:
- move mdss node to preserve the unit address sort order
- remove _clk suffix from dsi clocks
(both the comments are from Doug Anderson)
Changes in v5:
- Keep the device status "disabled" by default (Bjorn Andersson)
- Use MDSS_GDSC macro (Jordan)
- Fix phy-names (Jordan)
- List reg ranges in numerical order (Jordan)
Changes in v6:
- Separating this patch out of the series
- fix phy-names
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
gpiio5 is missspelt in msm8996-pins.dtsi, fix that.
Signed-off-by: Jakob Wuhrer <jakobwuhrer@airmail.cc>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In the same way as for msm8974-hammerhead, l11 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Tested on Dragonboard-410c and DART-SD410 boards.
Fixes: 4c7d53d16d (arm64: dts: apq8016-sbc: add regulators support)
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The PMS405 PMIC has an ADC that exposes the on-die temperature that we
wire up to spmi-temp-alarm thermal driver. This allows the PMIC
temperature to be exposed to Linux through the thermal framework.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on qcs404 soc.
Optional clock and regulator controls are not yet available in
upstream, hence add them once available.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The controller can support EXT_CSD_CARD_TYPE_HS400_1_8V cards.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This change adds the cpufreq node as per the bindings example for SDM845.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the second lane registers for the USB PHY, now that the
QMP phy bindings have been updated. This way the driver can stop
reaching beyond its register region to get at the second lane.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the UFS host controller and PHY on sdm845-mtp.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the UFS controller and PHY to SDM845.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add iommu context for the host controller]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for arm,mmu-500 available on sdm845.
This MMU-500 with single TCU and multiple TBU architecture
is shared among all the peripherals except gpu.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable support for one of the micro SD slots on the MTP.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add one of the two SD controllers to SDM845.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
