Commit Graph

366 Commits

Author SHA1 Message Date
Mark Brown
6ad45a27cb spi: Make core DMA mapping functions generate scatterlists
We cannot unconditionally use dma_map_single() to map data for use with
SPI since transfers may exceed a page and virtual addresses may not be
provided with physically contiguous pages. Further, addresses allocated
using vmalloc() need to be mapped differently to other addresses.

Currently only the MXS driver handles all this, a few drivers do handle
the possibility that buffers may not be physically contiguous which is
the main potential problem but many don't even do that. Factoring this
out into the core will make it easier for drivers to do a good job so if
the driver is using the core DMA code then generate a scatterlist
instead of mapping to a single address so do that.

This code is mainly based on a combination of the existing code in the MXS
and PXA2xx drivers. In future we should be able to extend it to allow the
core to concatenate adjacent transfers if they are compatible, improving
performance.

Currently for simplicity clients are not allowed to use the scatterlist
when they do DMA mapping, in the future the existing single address
mappings will be replaced with use of the scatterlist most likely as
part of pre-verifying transfers.

This change makes it mandatory to use scatterlists when using the core DMA
mapping so update the s3c64xx driver to do this when used with dmaengine.
Doing so makes the code more ugly but it is expected that the old s3c-dma
code can be removed very soon.

Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-04 20:31:49 +00:00
Mark Brown
3a2eba9bd0 spi: Provide core support for full duplex devices
It is fairly common for SPI devices to require that one or both transfer
directions is always active. Currently drivers open code this in various
ways with varying degrees of efficiency. Start factoring this out by
providing flags SPI_MASTER_MUST_TX and SPI_MASTER_MUST_RX. These will cause
the core to provide buffers for the requested direction if none are
specified in the underlying transfer.

Currently this is fairly inefficient since we actually allocate a data
buffer which may get large, support for mapping transfers using a
scatterlist will allow us to avoid this for DMA based transfers.

Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-04 20:31:33 +00:00
Mark Brown
99adef310f spi: Provide core support for DMA mapping transfers
The process of DMA mapping buffers for SPI transfers does not vary between
devices so in order to save duplication of code in drivers this can be
factored out into the core, allowing it to be integrated with the work that
is being done on factoring out the common elements from the data path
including more sharing of dmaengine code.

In order to use this masters need to provide a can_dma() operation and while
the hardware is prepared they should ensure that DMA channels are provided
in tx_dma and rx_dma. The core will then ensure that the buffers are mapped
for DMA prior to calling transfer_one_message().

Currently the cleanup on error is not complete, this needs to be improved.

Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03 13:05:21 +00:00
Baruch Siach
e9305331f6 spi: correct the transfer_one_message documentation wording
The transfer_one_message callback handles messages, not transfers.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-27 18:45:02 +00:00
Baruch Siach
6e5f52674f spi: spi.h: clarify the documentation of transfer_one
Explicitly note the transfer_one and transfer_one_message are mutually
exclusive, to make the text a little more newcomers friendly.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-27 18:43:36 +00:00
Linus Torvalds
2d2e7d195b spi: Updates for v3.14
A respun version of the merges for the pull request previously sent with
 a few additional fixes.  The last two merges were fixed up by hand since
 the branches have moved on and currently have the prior merge in them.
 
 Quite a busy release for the SPI subsystem, mostly in cleanups big and
 small scattered through the stack rather than anything else:
 
  - New driver for the Broadcom BC63xx HSSPI controller.
  - Fix duplicate device registration for ACPI.
  - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
    changes upon which the transiton depends).
  - Some small optimisations to reduce the amount of time we hold locks
    in the datapath, eliminate some redundant checks and the size of a
    spi_transfer.
  - Lots of fixes, cleanups and general enhancements to drivers,
    especially the rspi and Atmel drivers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJS4RZvAAoJELSic+t+oim9XKAP/00WcCARVzqWmzZYhW2nCqVw
 zRu/DEC+RFlvUSOrwx5SojZNCJekKrsbJuzvapXKIj+SL5+wDm2gUo188s+J8e5V
 mXA9CGb2+tQUgzuQzKZ82kf5WT1a/VpgdVqxZ2EGBHqdJwMV6cG20YneTd9/A0ar
 QbD9Ikon07cE6j8sp/HKxzSnER+3ii4OTJPJCXkNPHiDE9xkA/FR4qy/DksC2hpy
 y6IHCNGA3yHB/8bC7hxUKabOBwPpvQlGELTLHKTVy4umoAE0/aYSjwMdE67SbqXg
 mxDLcDjacNb4ga9hfWiYdZOKRdYiljt1zXksKHldp+R654YFTSVGmYipMoc0l52b
 jyycLM9ZjQ8Q74ySY+BIdZ4RDKFg4QajDhd/sIJtI354HLdoJCQa82j3luj6/Ewu
 JSlI4EGZUjOWPZb72kkrwj0LFBT5k639fMmLPDCLLlg5sUvx2afFl96s9Z25mFGj
 JzgwhjBIcF8AmllLTEpS6cP8MOBeThJ79gTxmbH60tsWxil2yCS4etg+h6GFo7g9
 GBXL9UF63Q6t9Mg8/0oACDs/YyMMbFImi6p20B+Pr0QZiltiTSSc4Z7eo4gG4UYh
 m4svqZcMG8w6csMAMb6I6a9+EojERPt53bZayasnnX/e5HsXJah4qop9Pjrma4ed
 PQHMx8ivWztwyqqjoYTz
 =CbUw
 -----END PGP SIGNATURE-----

Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A respun version of the merges for the pull request previously sent
  with a few additional fixes.  The last two merges were fixed up by
  hand since the branches have moved on and currently have the prior
  merge in them.

  Quite a busy release for the SPI subsystem, mostly in cleanups big and
  small scattered through the stack rather than anything else:

   - New driver for the Broadcom BC63xx HSSPI controller
   - Fix duplicate device registration for ACPI
   - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
     changes upon which the transiton depends)
   - Some small optimisations to reduce the amount of time we hold locks
     in the datapath, eliminate some redundant checks and the size of a
     spi_transfer
   - Lots of fixes, cleanups and general enhancements to drivers,
     especially the rspi and Atmel drivers"

* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
  spi: core: Fix transfer failure when master->transfer_one returns positive value
  spi: Correct set_cs() documentation
  spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
  spi: Spelling s/finised/finished/
  spi: sc18is602: Convert to use bits_per_word_mask
  spi: Remove duplicate code to set default bits_per_word setting
  spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
  spi: clps711x: Add MODULE_ALIAS to support module auto-loading
  spi: rspi: Add missing clk_disable() calls in error and cleanup paths
  spi: rspi: Spelling s/transmition/transmission/
  spi: rspi: Add support for specifying CPHA/CPOL
  spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
  spi: rspi: Add more QSPI register documentation
  spi: rspi: Add more RSPI register documentation
  spi: rspi: Remove dependency on DMAE for SHMOBILE
  spi/s3c64xx: Correct indentation
  spi: sh: Use spi_sh_clear_bit() instead of open-coded
  spi: bitbang: Grammar s/make to make/to make/
  spi: sh-hspi: Spelling s/recive/receive/
  spi: core: Improve tx/rx_nbits check comments
  ...
2014-01-25 13:20:36 -08:00
Mark Brown
8aeab58e56 Merge remote-tracking branches 'spi/topic/pxa2xx', 'spi/topic/qspi', 'spi/topic/s3c24xx', 'spi/topic/s3c64xx', 'spi/topic/sh', 'spi/topic/tegra114', 'spi/topic/tegra20-sflash', 'spi/topic/tegra20-slink', 'spi/topic/txx9' and 'spi/topic/xcomm' into spi-linus 2014-01-23 13:07:14 +00:00
Mark Brown
3c1039745e Merge remote-tracking branch 'spi/topic/core' into spi-linus 2014-01-23 13:07:01 +00:00
Geert Uytterhoeven
bd6857a0c6 spi: Correct set_cs() documentation
The documentation for spi_master.set_cs() says:

    assert or deassert chip select, true to assert

i.e. its "enable" parameter uses assertion-level logic.

This does not match the implementation of spi_set_cs(), which calls
spi_master.set_cs() with the wanted logic level of the chip select line,
which depends on the polarity of the chip select signal.

Correct the documentation to match the implementation.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-21 18:11:49 +00:00
Geert Uytterhoeven
0516712c65 spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-21 18:11:49 +00:00
Geert Uytterhoeven
269ccca8ec spi: Kill superfluous cast in spi_w8r16()
spi_write_then_read() takes a "void *" for rxbuf, so there's no need to
cast the buffer pointer to "u8 *".

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-13 11:20:21 +00:00
Mark Brown
d3fbd45701 spi: Use bitfields for multiple data lines
Trent Piepho observed that since the current realistic maximum number of
data lines is four we can pack the spi_transfer struct more efficiently
if we use a bitfield for the number of bits, allowing the fields to fit
in a single byte along with cs_change.

If space becomes an issue further optimiation is possible by only using
the constants and packing the values chosen for them.

Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-13 10:13:28 +00:00
Sachin Kamat
85a9012446 spi: s3c24xx: Remove reference to plat/fiq.h
fiq.h contains only a function declaration and is not used by anyone
else. Move the declaration to the driver header file and remove the
unnecessary platform dependency from the driver.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-08 13:06:21 +00:00
Trent Piepho
89c1f60746 spi: Order fields in spi_device for better packing
Now that spi_device->mode is a u16, the chip_select, bits_per_mode,
and mode fields pack poorly, taking 8 bytes:  four data and four
padding.  By moving (u8)bits_per_word up one position, to after
(u8)chip_select, they pack better and only use 4 bytes.

Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>g
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-16 21:03:42 +00:00
Alexander Shiyan
61e7380403 gpio: 74x164: Remove non-DT support
Commit 20bc4d5d56
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-12 14:27:57 +01:00
Mark Brown
82f85cf98f Merge remote-tracking branch 'spi/topic/wr' into spi-next 2013-10-25 09:51:41 +01:00
Mark Brown
ad14ad735f Merge remote-tracking branch 'spi/topic/rspi' into spi-next 2013-10-25 09:51:37 +01:00
Mark Brown
2cc6e2e0c8 Merge remote-tracking branch 'spi/topic/s3c64xx' into spi-loop 2013-10-11 20:10:13 +01:00
Mark Brown
b158935f70 spi: Provide common spi_message processing loop
The loops which SPI controller drivers use to process the list of transfers
in a spi_message are typically very similar and have some error prone areas
such as the handling of /CS. Help simplify drivers by factoring this code
out into the core - if drivers provide a transfer_one() function instead
of a transfer_one_message() function the core will handle processing at the
message level.

/CS can be controlled by either setting cs_gpio or providing a set_cs
function. If this is not possible for hardware reasons then both can be
omitted and the driver should continue to implement manual /CS handling.

This is a first step in refactoring and it is expected that there will be
further enhancements, for example factoring out of the mapping of transfers
for DMA and the initiation and completion of interrupt driven transfers.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-11 20:09:50 +01:00
Mark Brown
2841a5fc37 spi: Provide per-message prepare and unprepare operations
Many SPI drivers perform setup and tear down on every message, usually
doing things like DMA mapping the message. Provide hooks for them to use
to provide such operations.

This is of limited value for drivers that implement transfer_one_message()
but will be of much greater utility with future factoring out of standard
implementations of that function.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-11 20:09:13 +01:00
Lars-Peter Clausen
05071aa864 spi: Add a spi_w8r16be() helper
This patch adds a new spi_w8r16be() helper, which is similar to spi_w8r16()
except that it converts the read data word from big endian to native endianness
before returning it. The reason for introducing this new helper is that for SPI
slave devices it is quite common that the read 16 bit data word is in big
endian. So users of spi_w8r16() have to convert the result to native endianness
manually. A second reason is that in this case the endianness of the return
value of spi_w8r16() depends on its sign. If it is negative (i.e. a error code)
it is already in native endianness, if it is positive it is in big endian. The
sparse code checker doesn't like this kind of mixed endianness and special
annotations are necessary to keep it quiet (E.g. casting to be16 using __force).
Doing the conversion to native endianness in the helper function does not
require such annotations since we are not mixing different endiannesses in the
same variable.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-03 13:52:03 +01:00
Mark Brown
666d5b4c74 spi: core: Add devm_spi_register_master()
Help simplify the cleanup code for SPI master drivers by providing a
managed master registration function, ensuring that the master is
automatically unregistered whenever the device is unbound.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-17 00:59:36 +01:00
Hiep Cao Minh
5ce0ba8865 spi: rcar: add Renesas QSPI support on RSPI
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.

Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-17 00:22:50 +01:00
Linus Torvalds
d0048f0b91 MMC highlights for 3.12:
Core:
  - Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
  - The slot-gpio helper can now handle GPIO debouncing card-detect.
  - Read supported voltages from DT "voltage-ranges" property.
 
 Drivers:
  - dw_mmc: Add support for ARC architecture, and support exynos5420.
  - mmc_spi: Support CD/RO GPIOs.
  - sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
  - sh_mmcif: Add DT support for DMA channels.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.13 (GNU/Linux)
 
 iQIcBAABAgAGBQJSLxu8AAoJEHNBYZ7TNxYMkV8P/RZMkP3L88wPmvdQ4IxVD/Bg
 jphPsZTAlY8pLY7EcBVfbIGfBMMoVZ8CayuAbj9u5jFiMBNDUKRnKrky1m95F62n
 xXiS5vUiKdWpByMpfKmrqvJr6eS8SWq5z/yug1c3s1Y9T363KgfypgJLvNgbMGiv
 qbmjE+Zw65nMwHCk+4Rvq6s4aN6KosRZP0ABsn1foXt3kybSgemp5ShrlEyXohfS
 E91EiYxHFC4fdmuWiZZvL1tyHFeV25omyZA90mpkioNItiwoyOM2rfjfEfNq+WBw
 UrmdBesbGsF0Zi12CBa9LtzdRjYK8PugBWKW3mycS5++NX9KW6Ac/EpGqFeH9KgL
 WZ2v4aQjkbnzQKUB2HcWAyXm88G9MkNvpLbIrmIPtson+q0UjgPYWe5BI3dy/Y1v
 YS1JeseslVtSTKzGYsa1GJ7Nc1xYiILRz0RS4YGYXNjwvrl89i2UH7cglYDW36Xd
 vxvRBaFpVsj1mfjjITEoG6nE0v5aYH6gSITY79XR+/kN871/99/oIUaWdpjcm9yv
 SIYmK7ipcvxugkQ7BoMGbym/dvuUrZ+Vnf8dFlGPTJegZVsnfgrVAnRpvcVwW8+x
 4Z79wUPSIETRqj2XX2I/Y0JnrXry+dLLVyeK1tELoeOKev73Ai2lcqPSz6J0tzJs
 IErcz0hM1znL2RtgNwio
 =+EYB
 -----END PGP SIGNATURE-----

Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.12:

  Core:
   - Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
   - The slot-gpio helper can now handle GPIO debouncing card-detect.
   - Read supported voltages from DT "voltage-ranges" property.

  Drivers:
   - dw_mmc: Add support for ARC architecture, and support exynos5420.
   - mmc_spi: Support CD/RO GPIOs.
   - sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
   - sh_mmcif: Add DT support for DMA channels"

* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
  Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
  mmc: dw_mmc: Add support for ARC
  mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
  mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
  mmc: esdhc: add support to get voltage from device-tree
  mmc: sdhci: get voltage from sdhc host
  mmc: core: parse voltage from device-tree
  mmc: omap_hsmmc: use the generic config for omap2plus devices
  mmc: omap_hsmmc: clear status flags before starting a new command
  mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
  mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
  mmc: sh_mmcif: revision-specific Command Completion Signal handling
  mmc: sh_mmcif: add support for Device Tree DMA bindings
  mmc: sh_mmcif: move header include from header into .c
  mmc: SDHI: add DT compatibility strings for further SoCs
  mmc: dw_mmc-pci: enable bus-mastering mode
  mmc: dw_mmc-pci: get resources from a proper BAR
  mmc: tmio-mmc: Remove .set_pwr() callback from platform data
  mmc: tmio-mmc: Remove .get_cd() callback from platform data
  mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
  ...
2013-09-10 13:33:09 -07:00
Mark Brown
85cac43132 Merge remote-tracking branch 'spi/topic/qspi' into spi-next 2013-09-01 13:49:06 +01:00
Mark Brown
9020b75467 Merge remote-tracking branch 'spi/topic/msglen' into spi-next 2013-09-01 13:48:58 +01:00
Mark Brown
db04e17055 Merge remote-tracking branch 'spi/topic/checks' into spi-next 2013-09-01 13:48:48 +01:00
Mark Brown
8e28fb63a7 Merge remote-tracking branch 'spi/topic/bpw' into spi-next 2013-09-01 13:48:46 +01:00
Laurent Pinchart
62b6af5c7e mmc: mmc_spi: Remove platform data .get_cd() and .get_ro() callbacks
All platforms now pass the CD and RO GPIOs to the MMC SPI driver, those
callbacks are not used anymore. Remove them.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2013-08-24 23:58:06 -04:00
Laurent Pinchart
bf287a90ce mmc: mmc_spi: Support CD/RO GPIOs
Add support for passing CD/RO GPIO numbers directly to the mmc_spi
driver instead of relying solely on board code callbacks to retrieve the
CD/RO signals values. The driver will enable debouncing on the card
detect GPIO if the cd_debounce field is set to a non-zero value.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2013-08-24 23:45:22 -04:00
Mark Brown
21e34a3306 Merge remote-tracking branch 'spi/topic/quad' into spi-qspi 2013-08-23 12:00:15 +01:00
wangyuhang
f477b7fb13 spi: DUAL and QUAD support
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
   "spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
   previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
   SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
   (1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
      single, dual and quad.
   (2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
      example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
               to QUAD(SPI_NBITS_QUAD)
   (3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
      single(SPI_NBITS_SINGLE)

Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-22 13:47:29 +01:00
Stephen Warren
b6aa23ccae spi: fix SPI_BIT_MASK so it always fits into 32-bits
On a 64-bit platform, ~0UL fills 64-bits, which causes SPI_BIT_MASK(32)
not to fit into 32 bits. This causes a warning when the result is assigned
to a 32-bit variable. Use ~0U instead to prevent this. This fixes:

drivers/spi/spi-gpio.c: In function 'spi_gpio_probe':
drivers/spi/spi-gpio.c:446:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-08-02 11:31:22 +01:00
Mark Brown
49834de234 spi: Provide core support for runtime PM during transfers
Most SPI drivers that implement runtime PM support use identical code to
do so: they acquire a runtime PM lock in prepare_transfer_hardware() and
then they release it in unprepare_transfer_hardware(). The variations in
this are mostly missing error checking and the choice to use autosuspend.

Since these runtime PM calls are normally the only thing in the prepare
and unprepare callbacks and the autosuspend API transparently does the
right thing on devices with autosuspend disabled factor all of this out
into the core with a flag to enable the behaviour.

Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2013-07-29 17:59:20 +01:00
Sourav Poddar
078726ce6d driver: spi: Modify core to compute the message length
Make spi core calculate the message length while
populating the other transfer parameters.

Usecase, driver can use it to populate framelength filed in their
controller.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-18 16:22:01 +01:00
Mark Brown
2025172e32 spi/bitbang: Use core message pump
Convert drivers using bitbang to use the core mesasge pump infrastructure,
saving some code and meaning that these drivers get to take advantage of
work done on improving the core implementation.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-17 18:13:01 +01:00
Mark Brown
a2fd4f9fa3 spi: Support transfer speed checking in the core
Allow drivers to avoid implementing their own checks for simple rates by
specifying the limits in the master structure.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-15 11:34:51 +01:00
Mark Brown
874b315856 spi/bitbang: Unexport spi_bitbang_transfer()
Currently no drivers use the ability to override spi_bitbang_transfer()
and if any started this would make it harder to convert the bitbang code
to use transfer_one_message() so remove the export in order to prevent
anyone starting.

Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-15 11:29:52 +01:00
Mark Brown
ed893559c9 Merge remote-tracking branch 'spi/topic/xilinx' into spi-next 2013-06-26 16:21:06 +01:00
Michal Simek
082339bc63 spi: spi-xilinx: Add run run-time endian detection
Do not load endian value from platform data
and rather autodetect it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-04 18:37:35 +01:00
Stephen Warren
eca8960a8e spi: fix incorrect handling of min param in SPI_BPW_RANGE_MASK
SPI_BPW_RANGE_MASK is intended to work by calculating two masks; one
representing support for all bits up-to-and-including the "max" supported
value, and one representing support for all bits up-to-but-not-including
the "min" supported value, and then taking the difference between the
two, resulting in a mask representing support for all bits between
(inclusive) the min and max values.

However, the second mask ended up representing all bits up-to-and-
including rather up-to-but-not-including. Fix this bug.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-01 19:46:16 +01:00
Stephen Warren
4dd9572abc spi: fix undefined behaviour in SPI_BPW_RANGE_MASK
The parameters to SPI_BPW_RANGE_MASK() are in the range 1..32. If 32 is
used as a parameter, part of the expression is "1 << 32". Since 32 is >=
the size of the type in use, such a shift is undefined behaviour. Add
macro SPI_BIT_MASK to Implement a special case and thus avoid undefined
behaviour. Use this new macro rather than BIT() when implementing
SPI_BPW_RANGE_MASK().

This fixes build warnings such as:
drivers/spi/spi-gpio.c:446:2: warning: left shift count >= width of type [enabled by default]

SPI_BPW_MASK() already avoids this, since its parameter is also in range
1..32, yet it only shifts by up to one less than the input parameter.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-01 19:46:16 +01:00
Stephen Warren
2922a8de99 spi: introduce macros to set bits_per_word_mask
Introduce two macros to make setting up spi_master.bits_per_word_mask
easier, and avoid mistakes like writing BIT(n) instead of BIT(n - 1).

SPI_BPW_MASK is for a single supported value of bits_per_word_mask.

SPI_BPW_RANGE_MASK represents a contiguous set of bit lengths.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-05-22 10:57:43 -05:00
Mark Brown
88b0357dde Merge remote-tracking branch 'spi/fix/grant' into spi-linus 2013-05-13 18:27:18 +04:00
Linus Torvalds
38f56f33ca ARM: arm-soc device tree changes, part 2
These are mostly new device tree bindings for existing drivers, as well
 as changes to the device tree source files to add support for those
 devices, and a couple of new boards, most notably Samsung's Exynos5
 based Chromebook.
 
 The changes depend on earlier platform specific updates and touch
 the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUYgjh2CrR//JCVInAQJTvRAAmxaeoI+kQ/pbbRDa/Mnhf+bUmQjvJvx4
 uFGYAAi23Txem2Bx6xrfvOo9//ATYSfRxenoSSOtXQucsnrqD0+837Sj2NbO6AB9
 MSiFDK4usJtGwSUybkSHNLb2QPBr8XTgmyWVE/sHEw2UtrIToC1n3sxFofFm0guT
 ReILKsgK0Wjyq5RntnjWOCHNNp6OGqDGvFXlSJqNA7Z6gR/VZy4o0oXS4Sv3TWgF
 zG7ngSG7/u9FP1IQnMr/SxY1T4QS/bBbAC1YvD/7X30DPHrWKR3/3LfLcsc9TUN2
 smTlZQjHdgBbGfVPL7JN0fQwA82HEjNSZKLJ0w9uFjxXgnoKT3znpUpQeuf3dsWm
 BhEFqN1Rf446S4ft2btBSB2nhX4NTlJ7w6z2F65xgaylgYFsGFTYcpjiOurKe3wF
 gGsw31DZdcuI4/LjiWbNGRKbMd7HFFLbFDMJ16TFbNcNr+pM3qpoQ6z3uMbfCBSe
 xFnYr+ESN8F2HXMNLiz3CTqLY+Fi/bHd22n3KuI9qsWws/0KDUrTvFh9Sm3kYji5
 QwwLl6PRoeFw8H29e3KrPsKoY/BGYAvrAetnC1o79cDFPLwUyii/1B6WwzC4ynfs
 K1VhwdVOwnp0sS/a2Pv8sZBpDNI07gwT9P20aiholxgREq2RKNXXVxGGFfK5Qvm9
 FG4Vp6EKEQ0=
 =G60S
 -----END PGP SIGNATURE-----

Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
 "These are mostly new device tree bindings for existing drivers, as
  well as changes to the device tree source files to add support for
  those devices, and a couple of new boards, most notably Samsung's
  Exynos5 based Chromebook.

  The changes depend on earlier platform specific updates and touch the
  usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."

* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: exynos: dts: cros5250: add EC device
  ARM: dts: Add sbs-battery for exynos5250-snow
  ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
  ARM: dts: add mshc controller node for Exynos4x12 SoCs
  ARM: dts: Add chip-id controller node on Exynos4/5 SoC
  ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
  ARM: davinci: da850-evm: add SPI flash support
  ARM: davinci: da850: override SPI DT node device name
  ARM: davinci: da850: add SPI1 DT node
  spi/davinci: add DT binding documentation
  spi/davinci: no wildcards in DT compatible property
  ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
  ARM: dts: mvebu: introduce internal-regs node
  ARM: dts: mvebu: Convert all the mvebu files to use the range property
  ARM: dts: mvebu: move all peripherals inside soc
  ARM: dts: mvebu: fix cpus section indentation
  ARM: davinci: da850: add EHRPWM & ECAP DT node
  ARM/dts: OMAP3: fix pinctrl-single configuration
  ARM: dts: Add OMAP3430 SDP NOR flash memory binding
  ARM: dts: Add NOR flash bindings for OMAP2420 H4
  ...
2013-05-07 11:06:17 -07:00
Linus Torvalds
73287a43cc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights (1721 non-merge commits, this has to be a record of some
  sort):

   1) Add 'random' mode to team driver, from Jiri Pirko and Eric
      Dumazet.

   2) Make it so that any driver that supports configuration of multiple
      MAC addresses can provide the forwarding database add and del
      calls by providing a default implementation and hooking that up if
      the driver doesn't have an explicit set of handlers.  From Vlad
      Yasevich.

   3) Support GSO segmentation over tunnels and other encapsulating
      devices such as VXLAN, from Pravin B Shelar.

   4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.

   5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
      Dukkipati.

   6) In the PHY layer, allow supporting wake-on-lan in situations where
      the PHY registers have to be written for it to be configured.

      Use it to support wake-on-lan in mv643xx_eth.

      From Michael Stapelberg.

   7) Significantly improve firewire IPV6 support, from YOSHIFUJI
      Hideaki.

   8) Allow multiple packets to be sent in a single transmission using
      network coding in batman-adv, from Martin Hundebøll.

   9) Add support for T5 cxgb4 chips, from Santosh Rastapur.

  10) Generalize the VXLAN forwarding tables so that there is more
      flexibility in configurating various aspects of the endpoints.
      From David Stevens.

  11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
      from Dmitry Kravkov.

  12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
      Neira Ayuso.

  13) Start adding networking selftests.

  14) In situations of overload on the same AF_PACKET fanout socket, or
      per-cpu packet receive queue, minimize drop by distributing the
      load to other cpus/fanouts.  From Willem de Bruijn and Eric
      Dumazet.

  15) Add support for new payload offset BPF instruction, from Daniel
      Borkmann.

  16) Convert several drivers over to mdoule_platform_driver(), from
      Sachin Kamat.

  17) Provide a minimal BPF JIT image disassembler userspace tool, from
      Daniel Borkmann.

  18) Rewrite F-RTO implementation in TCP to match the final
      specification of it in RFC4138 and RFC5682.  From Yuchung Cheng.

  19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
      you like netlink, so I implemented netlink dumping of netlink
      sockets.") From Andrey Vagin.

  20) Remove ugly passing of rtnetlink attributes into rtnl_doit
      functions, from Thomas Graf.

  21) Allow userspace to be able to see if a configuration change occurs
      in the middle of an address or device list dump, from Nicolas
      Dichtel.

  22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
      Frederic Sowa.

  23) Increase accuracy of packet length used by packet scheduler, from
      Jason Wang.

  24) Beginning set of changes to make ipv4/ipv6 fragment handling more
      scalable and less susceptible to overload and locking contention,
      from Jesper Dangaard Brouer.

  25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
      instead.  From Hong Zhiguo.

  26) Optimize route usage in IPVS by avoiding reference counting where
      possible, from Julian Anastasov.

  27) Convert IPVS schedulers to RCU, also from Julian Anastasov.

  28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
      Eitzenberger.

  29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
      nfnetlink_log, and nfnetlink_queue.  From Gao feng.

  30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.

  31) Support several new r8169 chips, from Hayes Wang.

  32) Support tokenized interface identifiers in ipv6, from Daniel
      Borkmann.

  33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.

  34) Add 802.1ad vlan offload support, from Patrick McHardy.

  35) Support mmap() based netlink communication, also from Patrick
      McHardy.

  36) Support HW timestamping in mlx4 driver, from Amir Vadai.

  37) Rationalize AF_PACKET packet timestamping when transmitting, from
      Willem de Bruijn and Daniel Borkmann.

  38) Bring parity to what's provided by /proc/net/packet socket dumping
      and the info provided by netlink socket dumping of AF_PACKET
      sockets.  From Nicolas Dichtel.

  39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
      Poirier"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
  filter: fix va_list build error
  af_unix: fix a fatal race with bit fields
  bnx2x: Prevent memory leak when cnic is absent
  bnx2x: correct reading of speed capabilities
  net: sctp: attribute printl with __printf for gcc fmt checks
  netlink: kconfig: move mmap i/o into netlink kconfig
  netpoll: convert mutex into a semaphore
  netlink: Fix skb ref counting.
  net_sched: act_ipt forward compat with xtables
  mlx4_en: fix a build error on 32bit arches
  Revert "bnx2x: allow nvram test to run when device is down"
  bridge: avoid OOPS if root port not found
  drivers: net: cpsw: fix kernel warn on cpsw irq enable
  sh_eth: use random MAC address if no valid one supplied
  3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
  tg3: fix to append hardware time stamping flags
  unix/stream: fix peeking with an offset larger than data in queue
  unix/dgram: fix peeking with an offset larger than data in queue
  unix/dgram: peek beyond 0-sized skbs
  openvswitch: Remove unneeded ovs_netdev_get_ifindex()
  ...
2013-05-01 14:08:52 -07:00
Sascha Herrmann
43b5abe064 at86rf230: add irq type configuration option
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.

Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-16 16:34:07 -04:00
Andreas Larsson
446411e18b spi: Initialize cs_gpio and cs_gpios with -ENOENT
The return value from of_get_named_gpio is -ENOENT when the given index
matches a hole in the "cs-gpios" property phandle list. However, the
default value of cs_gpio in struct spi_device and entries of cs_gpios in
struct spi_master is -EINVAL, which is documented to indicate that a
GPIO line should not be used for the given spi_device.

This sets the default value of cs_gpio in struct spi_device and entries
of cs_gpios in struct spi_master to -ENOENT. Thus, -ENOENT is the only
value used to indicate that no GPIO line should be used.

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-07 10:12:20 +01:00
Stephen Warren
5e49035e26 spi/tegra: remove unused Tegra platform data header
The platform data header is no longer used. Delete it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-07 10:07:59 +01:00
Shawn Guo
26aafa77df spi: mxs-spi: move to use generic DMA helper
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.

Since mxs is a DT only platform now, along with the changes, the non-DT
case handling in probe function also gets removed.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2013-04-04 21:22:44 +08:00
Stephen Warren
543bb255a1 spi: add ability to validate xfer->bits_per_word in SPI core
Allow SPI masters to define the set of bits_per_word values they support.
If they do this, then the SPI core will reject transfers that attempt to
use an unsupported bits_per_word value. This eliminates the need for each
SPI driver to implement this checking in most cases.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-01 14:14:32 +01:00
Linus Torvalds
b5c78e04dd Staging tree update for 3.9-rc1
Here's the big staging tree merge for 3.9-rc1
 
 Lots of cleanups and updates for drivers all through the staging tree.
 We are pretty much "code neutral" here, adding just about as many lines
 as we removed.
 
 All of these have been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEUEABECAAYFAlEmW7QACgkQMUfUDdst+ymlIACXT5mv8Y5A/KJa+QLTNNsofI8u
 aACgq9hNZxJzX6VQMLXUV8+2SILOqYo=
 =5wIj
 -----END PGP SIGNATURE-----

Merge tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging tree update from Greg Kroah-Hartman:
 "Here's the big staging tree merge for 3.9-rc1

  Lots of cleanups and updates for drivers all through the staging tree.
  We are pretty much "code neutral" here, adding just about as many
  lines as we removed.

  All of these have been in linux-next for a while."

* tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (804 commits)
  staging: comedi: vmk80xx: wait for URBs to complete
  staging: comedi: drivers: addi-data: hwdrv_apci3200.c: Add a missing semicolon
  staging: et131x: Update TODO list
  staging: et131x: Remove assignment of skb->dev
  staging: wlan-ng: hfa384x.h: fix for error reported by smatch
  staging/zache checkpatch ERROR: spaces prohibited around that
  staging/ozwpan: Mark read only parameters and structs as const
  staging/ozwpan: Remove empty and unused function oz_cdev_heartbeat
  staging/ozwpan: Mark local functions as static (fix sparse warnings)
  staging/ozwpan: Add missing header includes
  staging/usbip: Mark local functions as static (fix sparse warnings)
  staging/xgifb: Remove duplicated code in loops.
  staging/xgifb: Consolidate return paths
  staging/xgifb: Remove code without effect
  staging/xgifb: Remove unnecessary casts
  staging/xgifb: Consolidate if/else if with identical code branches
  staging: vt6656: replaced custom TRUE definition with true
  staging: vt6656: replaced custom FALSE definition with false
  staging: vt6656: replace custom BOOL definition with bool
  staging/rtl8187se: Mark functions as static to silence sparse
  ...
2013-02-21 12:11:44 -08:00
Andreas Larsson
095c3752e6 spi: Document cs_gpios and cs_gpio in kernel-doc
This adds missing kernel-doc entries for cs_gpios in struct spi_master and
cs_gpio in struct spi_device.

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
[grant.likely: tweaked the language of the descriptions]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2013-02-11 00:05:31 +00:00
Lars-Peter Clausen
6d9eecd418 spi: Add helper functions for setting up transfers
Quite often the pattern used for setting up and transferring a synchronous SPI
transaction looks very much like the following:

	struct spi_message msg;
	struct spi_transfer xfers[] = {
		...
	};

	spi_message_init(&msg);
	spi_message_add_tail(&xfers[0], &msg);
	...
	spi_message_add_tail(&xfers[ARRAY_SIZE(xfers) - 1], &msg);

	ret = spi_sync(&msg);

This patch adds two new helper functions for handling this case. The first
helper function spi_message_init_with_transfers() takes a spi_message and an
array of spi_transfers. It will initialize the message and then call
spi_message_add_tail() for each transfer in the array. E.g. the following

	spi_message_init(&msg);
	spi_message_add_tail(&xfers[0], &msg);
	...
	spi_message_add_tail(&xfers[ARRAY_SIZE(xfers) - 1], &msg);

can be rewritten as

	spi_message_init_with_transfers(&msg, xfers, ARRAY_SIZE(xfers));

The second function spi_sync_transfer() takes a SPI device and an array of
spi_transfers. It will allocate a new spi_message (on the stack) and add all
transfers in the array to the message. Finally it will call spi_sync() on the
message.

E.g. the follwing

	struct spi_message msg;
	struct spi_transfer xfers[] = {
		...
	};

	spi_message_init(&msg);
	spi_message_add_tail(&xfers[0], &msg);
	...
	spi_message_add_tail(&xfers[ARRAY_SIZE(xfers) - 1], &msg);

	ret = spi_sync(spi, &msg);

can be rewritten as

	struct spi_transfer xfers[] = {
		...
	};

	ret = spi_sync_transfer(spi, xfers, ARRAY_SIZE(xfers));

A coccinelle script to find such instances will follow.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-02-09 11:02:07 +00:00
Mika Westerberg
a0d2642e92 spi/pxa2xx: add support for Intel Low Power Subsystem SPI
Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:

	o FIFO depth is 256 entries
	o RX FIFO has one watermark
	o TX FIFO has two watermarks, low and high
	o chip select can be controlled by writing to a register

The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.

We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-02-08 13:14:40 +00:00
Mika Westerberg
5928808ef6 spi/pxa2xx: add support for DMA engine
To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.

Request lines and channel numbers can be passed to the driver from the
platform specific data.

The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-02-08 12:15:28 +00:00
Mika Westerberg
cd7bed0034 spi/pxa2xx: break out the private DMA API usage into a separate file
The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).

While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.

Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-02-08 12:15:21 +00:00
Maxime Ripard
d560040f7d spi: spi-gpio: fix compilation warning on 64 bits systems
SPI_GPIO_NO_MOSI and SPI_GPIO_NO_MISO flags are type casted to unsigned
long, yet, they are to be stored in an unsigned int field in the
spi_gpio_platform_data structure.

This leads to the following warning during compilation on 64 bits systems:
warning: large integer implicitly truncated to unsigned type [-Woverflow]

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-31 18:25:44 +08:00
Mika Westerberg
3343b7a6d2 spi/pxa2xx: convert to the common clk framework
Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.

In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-26 15:21:37 +08:00
Mika Westerberg
851bacf590 spi/pxa2xx: embed the ssp_device to platform data
The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.

Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.

We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-08 11:00:32 +00:00
Grant Likely
7730cba2a5 Linux 3.7-rc8
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJQvPxHAAoJEHm+PkMAQRiGkFUIAJz761Kp4J4Nj/wrv5ZHGQso
 MHRbzMkSfRNz6lGCkgxS61ydYKtrV2vuE6VH8HriGlLkI8Lj7MaQTXvYSdj/O0zy
 yV/2H5R3s7n5JZTw3g3eOf3K33tL6xhwd4tYHI7QHjdzSzQyaNhuUuNhxrlT95iv
 twNetm0tyhpf76TurRzF14hLUaShVRXT/FrqWK9wgmGjg7Ij0xp+UFNkeUGUwbeF
 3HMJ98fdd0VD/W8qF5GZr3USks4C+NKtXEya8zQKc59XumKCiRJZmbE6JsJlp+OP
 CsHs7ZaNlInvPcKTFzkNs8ThYWC/NHBqLO5tX5UphW4qFSS39EmHd8igrwXLPaI=
 =RS1F
 -----END PGP SIGNATURE-----

Merge tag 'v3.7-rc8' into spi/next

Linux 3.7-rc8
2012-12-07 17:02:47 +00:00
Grant Likely
a34fc82e23 Merge branch 'spi-next' from git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git
Pull in the changes Mark has queued up for SPI
2012-12-06 13:58:31 +00:00
Jean-Christophe PLAGNIOL-VILLARD
7431798490 of_spi: add generic binding support to specify cs gpio
This will allow to use gpio for chip select with no modification in the
driver binding

When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).

So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:

cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;

Then it should be configured so that num_chipselect = 4 with the
following mapping:

cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-11-21 23:25:33 +00:00
Igor Grinberg
c4f4925439 Input: ads7846 - enable pendown GPIO debounce time setting
Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-21 13:09:56 -08:00
Laxman Dewangan
dc4dc36056 spi: tegra: add spi driver for SLINK controller
Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-30 18:38:35 +00:00
Linus Torvalds
4864ccbb5a spi: Fixes for v3.7
A bunch of fixes here, mostly minor except for the pl022 which has just
 been a bit of a shambles all round, the recent runtime PM changes have
 as far as I can tell never worked so they're just getting thrown out.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQhpP3AAoJELSic+t+oim9y5sP/2HlUw8SrFWVZNGkyZ/834KV
 3DuTZUEG0NAg39gMmnUiXH3ntfvNQBfWmqz9vJ/6Ec4gfCaXREwRNc4ZtkJuWzs+
 zvVoLJLgJ0FxxVP9Ul6K5lb4iPfAupu4up2TjlMWctRFJ0Og+Q68wqK/I58r9YGQ
 XhhCYy44MioBC/MyMToQ6iTnFjJ6ivj/RtHlZ72tLeDcF6/XRdCeLD/0Gd7pR1Ib
 jCnb6dzji+ztIATdz0zJ5dATz5UHKQ+sPKCOR/Aeb8w+XWwcllP7oCFJKYdpzzJj
 63y2wbRIrmF4wk9ZfCwD3LEFdeWL5MHKGUn47afqODnoYcKPOp7w5hlM5YH+ZNun
 3Elln9JPeg996GsN3HQNGM+Ip+g1mi3yCF1hDWIukPPewKI8zqSarlo5B4d0f73i
 wjNbgvEKXiRR3sD8osH9gz4rqubY9pNy3YRCBXYWsP+4jPyOmOjMDhOoc/MmVLc7
 0B0l6waynsZXelSXRDGDINGDrr5Kct4ZmAczWS8W0+wXw7ER7VHj7dbbMBEcDgny
 k80Zfo+VXPIj1+9pvy75JZJ91AWtnHz10hug5iuJNADt0F1rfpdeZZ1+F4U0S/4p
 KcT8IS39V813DfE8UITlg9TEdsV1z72DXiFRDpV/UOQY3oRH9tMn4SrX7crugWEF
 Y3XXO8xlXFdz+bj0rAoV
 =9XvI
 -----END PGP SIGNATURE-----

Merge tag 'spi-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc

Pull spi fixes from Mark Brown:
 "A bunch of fixes here, mostly minor except for the pl022 which has
  just been a bit of a shambles all round, the recent runtime PM changes
  have as far as I can tell never worked so they're just getting thrown
  out."

* tag 'spi-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
  spi/pl022: Revert recent runtime PM changes
  spi: tsc2005: delete soon-obsolete e-mail address
  spi: spi-rspi: fix build error for the latest shdma driver
2012-10-24 18:00:17 -07:00
David Howells
64d7155cdf UAPI: Remove empty non-UAPI Kbuild files
Remove non-UAPI Kbuild files that have become empty as a result of UAPI
disintegration.  They used to have only header-y lines in them and those have
now moved to the Kbuild files in the corresponding uapi/ directories.

Possibly these should not be removed but rather have a comment inserted to say
they are intentionally left blank.  This would make it easier to add generated
header lines in future without having to restore the infrastructure.

Note that at this point not all the UAPI disintegration parts have been merged,
so it is likely that more empty Kbuild files will turn up.

It is probably necessary to make the files non-empty to prevent the patch
program from automatically deleting them when it reduces them to nothing.

Signed-off-by: David Howells <dhowells@redhat.com>
2012-10-17 12:31:15 +01:00
Aaro Koskinen
2f5f1ce90a spi: tsc2005: delete soon-obsolete e-mail address
Delete soon-obsolete e-mail address.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 16:32:46 +09:00
David Howells
7939d3c2a6 UAPI: (Scripted) Disintegrate include/linux/spi
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
2012-10-09 09:49:03 +01:00
Marek Vasut
65defb9b3b mmc: spi: Pull out common DMA parts from MXS MMC
These parts will be used by the MXS SPI driver too.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:54:15 +01:00
Marek Vasut
1308239858 mmc: spi: Pull out the SSP clock configuration function
Pull out the MMC clock configuration function and make it
into SSP clock configuration function, so it can be used by
the SPI driver too.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:53:00 +01:00
Marek Vasut
829c1bf40b mmc: spi: Pull out parts shared between MMC and SPI
Abstract out the common part of private data shared between MMC
and SPI. These shall later allow to use common clock configuration
function.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:52:51 +01:00
Marek Vasut
f83b738065 mmc: spi: Add necessary bits into mxs-spi.h
Add missing register bits and registers into mxs-spi.h .
These will be used by the SPI driver.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:52:42 +01:00
Marek Vasut
600a991f98 mmc: spi: Rename IMX2[38]_MMC to IMX2[38]_SSP
Since the SSP controller can act as both SPI and MMC host,
renaming the enum to properly reflect the naming seems
appropriate.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:52:31 +01:00
Marek Vasut
8be3d3b2ac mmc: spi: Move SSP register definitions into separate file
Move the definitions into separate file so separate SPI driver can be
implemented. The SSP controller in MXS can act both as a MMC host and
as a SPI host.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-17 22:52:14 +01:00
Linus Torvalds
945c40c6b0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
 "First set of updates for the input subsystem.  You will get a new
  touchscreen driver (Melfas mms114), a new keypad driver for LPC32xx
  SoC, large update to Atmel mXT touchscreen driver, a lot of drivers
  acquired device tree support and a slew of other fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
  Input: add MELFAS mms114 touchscreen driver
  Input: add support for key scan interface of the LPC32xx SoC
  Input: omap4-keypad - add device tree support
  Input: hanwang - add support for Art Master II tablet
  Input: spear_keyboard - reconfigure operating frequency on suspend
  Input: spear_keyboard - fix clock handling during suspend/resume
  Input: ff-memless - fix a couple min_t() casts
  Input: synaptics - print firmware ID and board number at init
  Input: spear_keyboard - generalize keyboard frequency configuration
  Input: spear_keyboard - rename bit definitions to reflect register
  Input: spear_keyboard - use correct io accessors
  Input: spear-keyboard - fix disable device_init_wakeup in remove
  Input: wacom_i2c - fix compiler warning
  Input: imx_keypad - check error returned by clk_prepare_enable()
  Input: imx_keypad - adapt the new kpp clock name
  Input: imx_keypad - use clk_prepare_enable/clk_disable_unprepare()
  Input: ad7879 - add option to correct xy axis
  Input: synaptics_usb - Remove TrackPoint name trailing whitespace
  Revert "Input: atmel_mxt_ts - warn if sysfs could not be created"
  Input: MT - Include win8 support
  ...
2012-07-26 12:59:53 -07:00
Michael Hennerich
6680884a44 Input: ad7879 - add option to correct xy axis
Sebastian Zenker reported that driver swaps x and y samples when the
touchscreen leads are connected in accordance with the datasheet
specification.  Transposed axis can be typically corrected by touch
screen calibration however this bug also negatively influences touch
pressure measurements.

Add an option to correct x and y axis.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reported-and-tested-by: Sebastian Zenker <sebastian.zenker@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-07-06 19:12:26 -07:00
David S. Miller
b26d344c6b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/caif/caif_hsi.c
	drivers/net/usb/qmi_wwan.c

The qmi_wwan merge was trivial.

The caif_hsi.c, on the other hand, was not.  It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.

I did my best with that one and will ask Sjur to check it out.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-28 17:37:00 -07:00
alex.bluesman.smirnov@gmail.com
7b8e19b67c drivers/ieee802154: add support for the at86rf230/231 transceivers
The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.

This patch adds support for the Atmel RF230/231 radio transceivers.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-26 21:06:11 -07:00
Qiao Zhou
601722157b ARM: MMP: add pxa910-ssp into ssp_id_table
add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.

Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11 12:25:50 +08:00
Linus Torvalds
2795343705 arm-soc: clock driver changes
The new clock subsystem was merged in linux-3.4 without any users, this
 now moves the first three platforms over to it: imx, mxs and spear.
 
 The series also contains the changes for the clock subsystem itself,
 since Mike preferred to have it together with the platforms that require
 these changes, in order to avoid interdependencies and conflicts.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuexPAAoJEIwa5zzehBx3YBsP/0nFhXjb5t1PdLfFzGKtcZVB
 j4zXWXMHQ1fA7wIfEpZF3Nnco6MQkufF5wJPoPdn1+wmkzCn3D6IwNVWVtW4U5i9
 VGyShSbgusAAYXUe/9yYj8eN+bbRQSvdN4eWYWU6+rRXShGZ5dZZmp+IPNl54dnW
 6F8uCnHX0cnIMCpGqV+41zZgZ/4wL2k9gdqu0LO6pi07o4tGd0Z4gcySgUFAnn1R
 kofNHueYIP4UgOg8DREoBzVKlpRqMou3S2kSZUfMeb3Q9ryF7UIvaGqIILyi7PKL
 kWd3nptg0EPavfL21SwXHiGpnDpB/Gj/F70kcPLus5RYujB24C9bvBmc26z68NZx
 Sz9mbElkkIU5duZsl1nxBWJ8IZ/tSWdtmC2xQMznmV7gHyGgVwr4j47f4Uv5sBvM
 14JHDO7mqN6E6FnTFZu/oPAN5pDjgL+TVNK5BU6Wkq0zitrA6eyKDqCvBCqkO6Nn
 tNzOuyRDzMOwM7HzqXhxqtzJWXylO1Mldc4bM8X4Cocf4pnLna/X6uP6dgE6A+JY
 azVYx4I/0NdEPerDTzIcEhBDgZeBVROhUQr+kHxc4rf6WzUUbu/wEo1UKXWV66oW
 1jb1yAFFWqYjkQuQc2PD4JSx35sFJaoSaoneRtmzBzRDfzSr5KjKj1E0e1skyMFq
 7ZVLCqZD0cB9DhmMDkWP
 =rwFF
 -----END PGP SIGNATURE-----

Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc clock driver changes from Olof Johansson:
 "The new clock subsystem was merged in linux-3.4 without any users,
  this now moves the first three platforms over to it: imx, mxs and
  spear.

  The series also contains the changes for the clock subsystem itself,
  since Mike preferred to have it together with the platforms that
  require these changes, in order to avoid interdependencies and
  conflicts."

Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).

* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
  clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
  clk: Provide dummy clk_unregister()
  SPEAr: Update defconfigs
  SPEAr: Add SMI NOR partition info in dts files
  SPEAr: Switch to common clock framework
  SPEAr: Call clk_prepare() before calling clk_enable
  SPEAr: clk: Add General Purpose Timer Synthesizer clock
  SPEAr: clk: Add Fractional Synthesizer clock
  SPEAr: clk: Add Auxiliary Synthesizer clock
  SPEAr: clk: Add VCO-PLL Synthesizer clock
  SPEAr: Add DT bindings for SPEAr's timer
  ARM i.MX: remove now unused clock files
  ARM: i.MX6: implement clocks using common clock framework
  ARM i.MX35: implement clocks using common clock framework
  ARM i.MX5: implement clocks using common clock framework
  ARM: Kirkwood: Replace clock gating
  ARM: Orion: Audio: Add clk/clkdev support
  ARM: Orion: PCIE: Add support for clk
  ARM: Orion: XOR: Add support for clk
  ARM: Orion: CESA: Add support for clk
  ...
2012-05-26 12:42:29 -07:00
Linus Torvalds
be122abe4b SPI changes for v3.5 merge window
Bug fixes and new features for SPI device drivers.  Also move device
 tree support code out of drivers/of and into drivers/spi/spi.c where
 it makes more sense.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPvpHaAAoJEEFnBt12D9kBXNEQAIb6B0qhGn3l6coV6mr7ONiH
 zoZTNXk8hbXXgnt/4WGuIyLco5viea75h25JxdJGrB0hphvVsjhBn9AU6iwYVp//
 57PfkT89ST8ZzkuKwrJt5UNM7udOA8kvLSvYOVTdoOFV270JMQVw7dmkxj7zNKmq
 zy+Jy+3uRGqVzuges/me+YUeFUtw+nOd0ruJcgSfk7wze3bHY84IK8TTG3z/8jfj
 iQEv4a4A6waVDVIk45rWC/0Q2y+r1Ti1G9qzyegH1aNkh3IncsbgYfTcj6pf8YKx
 cFIgqE69xH4nyL35szV33HiC2LUb3dtGRRZ5gOTs39p2G9f39/xT2DxvQtSnQEAh
 3veUVoll8LsyvHMiSBIPStNSJ9pnI67oCm3MQOpGrx/dQsDo/hcI177QPW3U8wI0
 eeJbYhxz0rWRB2KA3Rbh7FXYqM2HuLGQ7Dx3iW2LLzaLDIiVuksw0D/NxeMOqdxM
 Ev6y/IPPVjhdlZ/ElYvhzRu9CquczFag1iA8ehfyp6i+xr08VF/ua9yi1dRfpxH6
 JfCSbj6HIofLugCP2pqS4W1qkCb+pXGosU8GQp/rffcXceQthX5oOk1JujNKxmJr
 K84ipRZW5bF14mmNSotI8oAda2oCfiDjFfrmXbFFprRebdoVKVPO1yFMJVXppWaa
 1k39oqBUiw4ypcBwEPgD
 =/Ux1
 -----END PGP SIGNATURE-----

Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6

Pull SPI changes from Grant Likely:
 "Bug fixes and new features for SPI device drivers.  Also move device
  tree support code out of drivers/of and into drivers/spi/spi.c where
  it makes more sense."

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  spi: By default setup spi_masters with 1 chipselect and dynamics bus number
  SPI: PRIMA2: use the newest APIs of PINCTRL to fix compiling errors
  spi/spi-fsl-spi: reference correct pdata in fsl_spi_cs_control
  spi: refactor spi-coldfire-qspi to use SPI queue framework.
  spi/omap2-mcspi: convert to the pump message infrastructure
  spi/rspi: add dmaengine support
  spi/topcliff: use correct __devexit_p annotation
  spi: Dont call prepare/unprepare transfer if not populated
  spi/ep93xx: clean probe/remove routines
  spi/devicetree: Move devicetree support code into spi directory
  spi: use module_pci_driver
  spi/omap2-mcspi: Trivial optimisation
  spi: omap2-mcspi: add support for pm_runtime autosuspend
  spi/omap: Remove bus_num usage for instance index
  OMAP : SPI : use devm_* functions
  spi: omap2-mcspi: convert to module_platform_driver
  spi: omap2-mcspi: make it behave as a module
2012-05-24 13:56:24 -07:00
Linus Torvalds
fb2123fad3 Char/Misc patches for 3.5-rc1
Here are a few various char/misc tree patches for the 3.5-rc1 merge window.
 
 Nothing major here at all, just different driver updates and some parport dead
 code removal.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iEYEABECAAYFAk+7qxoACgkQMUfUDdst+ynz0gCggUMf6y60T1rPVT7h2Ab3iy5k
 9d0An0U607GRDK1e5lwbZdGuuRkfBwRi
 =NpES
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull Char/Misc patches from Greg Kroah-Hartman:
 "Here are a few various char/misc tree patches for the 3.5-rc1 merge
  window.

  Nothing major here at all, just different driver updates and some
  parport dead code removal.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'char-misc-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  parport: remove unused dead code from lowlevel drivers
  xilinx_hwicap: reset XHI_MAX_RETRIES
  xilinx_hwicap: add support for virtex6 FPGAs
  Support M95040 SPI EEPROM
  misc: add support for bmp18x chips to the bmp085 driver
  misc: bmp085: add device tree properties
  misc: clean up bmp085 driver
  misc: do not mark exported functions __devexit
  misc: add missing __devexit_p() annotations
  pch_phub: delete duplicate definitions
  misc: Fix irq leak in max8997_muic_probe error path
2012-05-22 15:53:59 -07:00
Shimoda, Yoshihiro
a3633fe7aa spi/rspi: add dmaengine support
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-05-19 22:37:16 -06:00
Arnd Bergmann
3c0dec5f58 Merge branch 'clk-next' of git://git.linaro.org/people/mturquette/linux into next/clock
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
  clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
  clk: Provide dummy clk_unregister()
  ARM: Kirkwood: Replace clock gating
  ARM: Orion: Audio: Add clk/clkdev support
  ARM: Orion: PCIE: Add support for clk
  ARM: Orion: XOR: Add support for clk
  ARM: Orion: CESA: Add support for clk
  ARM: Orion: SDIO: Add support for clk.
  ARM: Orion: NAND: Add support for clk, if there is one.
  ARM: Orion: EHCI: Add support for enabling clocks
  ARM: Orion: SATA: Add per channel clk/clkdev support.
  ARM: Orion: UART: Get the clock rate via clk_get_rate().
  ARM: Orion: WDT: Add clk/clkdev support
  ARM: Orion: Eth: Add clk/clkdev support.
  ARM: Orion: SPI: Add clk/clkdev support.
  ARM: Orion: Add clocks using the generic clk infrastructure.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-16 16:35:25 +02:00
Andrew Lunn
4574b88669 ARM: Orion: SPI: Add clk/clkdev support.
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-05-08 16:33:55 -07:00
Randy Dunlap
dbabe0d659 spi: fix spi.h kernel-doc warning
Fix kernel-doc warning in spi.h (copy/paste):

Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-04-27 11:03:38 -06:00
Ivo Sieben
b4161f0bb5 Support M95040 SPI EEPROM
Updated the generic SPI EEPROM driver AT25 for support of an additional address
bit in the instruction byte. Certain EEPROMS have a size that is larger than the
number of address bytes would allow (e.g. like M95040 from ST that has 512 Byte
size but uses only one address byte (A0 to A7) for addressing.) For the extra
address bit (A8, A16 or A24) bit 3 of the instruction byte is used. This
instruction bit is normally defined as don't care for other AT25 like chips.

Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-18 14:57:57 -07:00
Linus Torvalds
09893ee845 ARM: More device tree support updates
This branch contains a number of updates for device tree support on
 several ARM platforms, in particular:
 
 * AT91 continues the device tree conversion adding support for a number of
   on-chip drivers and other functionality
 * ux500 adds probing of some of the core SoC blocks through device tree
 * Initial device tree support for ST SPEAr600 platforms
 * kirkwood continues the conversion to device-tree probing
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPcp12AAoJEIwa5zzehBx3c2oQAKkHhJFxYFaUSfAqUNQJtyLP
 ntNyjANchckGcmoGFRRn5q17leSW+GsPopeJF0uTSOq5xojrQJJnrfKCQmgTtdzt
 KiD9qJqF3bsM5PxdjkeQljiAirPZSKvyA6gZaPKozZb+NMk3ZMd3hYYi3j3EWR/c
 8C9HzwyuXUOKOQ1tHuQHEYnLAtcdVTpUnDGsQItD2Shw5H+AcoN1T00z6kWtXYoJ
 z/sFtBVvPxqozEEWbTEg2vm0XfT2ENlOIfHoOj+G2EfcVTjh4pSoD0TXwS11vjfX
 UEniGsdCSkQn0yKVuuLTNKy7BPkWXBUTxy6duIQMSs/57lgFEb9/+f5kgAol+Sdi
 OeUW4gYkZ8uAk2zOD4p1TGDZT/YHWQ2X3Wq2EhYNsYjZgbNCTlIIocet8jZ6Zfcm
 f7DdADS8ot8xFcZxMH7CFJ28cmEjhyGMSrMcrAq7HXrkX0ppFutF0CYkY/43uQ/h
 AGmP9wKi38PB1eXK44eAF25fRvT7ty7CiCBT88i8UZ3unj6raVbsGfqhvf5PbCki
 oX8dKFjPRRE4bj+8Si7LCTR00AIFMLxuftJw45L4syk+l6Y0y+b0HMBE3E/q7bbR
 dLBu3V/HHVMnuZv6vVgvI+dkZ9R6v2ychfoyKNh/AKvgXmr90diYbT0XAkcfSPk7
 +yy69EZA59UvLTxt9BmN
 =wiKV
 -----END PGP SIGNATURE-----

Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: More device tree support updates" from Olof Johansson:
 "This branch contains a number of updates for device tree support on
  several ARM platforms, in particular:

   * AT91 continues the device tree conversion adding support for a
     number of on-chip drivers and other functionality
   * ux500 adds probing of some of the core SoC blocks through device
     tree
   * Initial device tree support for ST SPEAr600 platforms
   * kirkwood continues the conversion to device-tree probing"

Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.

Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging.  It's called MACH_MOP500
now, and it was missed during previous merges.

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  ARM: SPEAr600: Add device-tree support to SPEAr600 boards
  ARM: ux500: Provide local timer support for Device Tree
  ARM: ux500: Enable PL022 SSP Controller in Device Tree
  ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
  ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
  ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
  ARM: ux500: db8500: list most devices in the snowball device tree
  ARM: ux500: split dts file for snowball into generic part
  ARM: ux500: combine the board init functions for DT boot
  ARM: ux500: Initial Device Tree support for Snowball
  ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
  ARM: kirkwood: use devicetree for rtc-mv
  ARM: kirkwood: rtc-mv devicetree bindings
  ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
  ARM: kirkwood: fdt: facilitate new boards during fdt migration
  ARM: kirkwood: fdt: absorb kirkwood_init()
  ARM: kirkwood: fdt: use mrvl ticker symbol
  ARM: orion: wdt: use resource vice direct access
  ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
  ARM: orion: spi: remove enable_clock_fix which is not used
  ...
2012-03-28 12:34:33 -07:00
Linus Torvalds
d61b7a572b ARM: global cleanups
Quite a bit of code gets removed, and some stuff moved around, mostly
 the old samsung s3c24xx stuff. There should be no functional changes
 in this series otherwise. Some cleanups have dependencies on other
 arm-soc branches and will be sent in the second round.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUAT2pCjGCrR//JCVInAQLd8RAAqCxhzSc4ewTUP/974gVhujj3TrpiEQcS
 FKvYWF76yP38Lbf3CJZBZaONRtrQNOhYpVQ0jb3WCV4F8mEH9PCes2q9RObeBYiY
 TNX8VdcuVjX2U9HaH0+RQtBUdujNLHpEOqtO57un7T5UDNssR5JOive1tNAooRv1
 pL0Hgx3AVqUbNOPpqQqHzy/MDdd67S6dX80yysANjFGMX87Nvp/ztYAdNnIdta+Z
 pDJt+DPlmK8LvjoSL3SEUN0p3Thk75621cCuauGq88PLIB2w62tzF0NFFbvIAgJT
 3aMlHM2flOiTJAWkUvA8zJiUzwv/0vYvH3xPoTo84abve3lVfZcY+fHNcfxE/Gge
 ri2MmkHyimVP3rNeyM0GbN1RTej1TN1MezeQW3nq2wP6nvS2k0/t32ObLLtWU7XA
 6iA0hKVMSnhqj4ln6jPAmyaDkaWHyYz97urhgetHqGadvLTiGPXCSBPalSiFmyMo
 11tvuqwUNz9tw4nsvGboFQwS2ZoVquC5inoHp5seqZETkGCB67JyeRGxtAM4gbP/
 wIRa3OBLY99yo1on6QovWNnSOMC6X4cOvBI/qHIjSEY/T9JVkslY87gRg3LkxCBR
 XpXfZ6iuLHoSRUGcIjE8D6KHjMgWIDPRnLkIliK4H+3Jn08g0R1MxCplevFCRtis
 egswZ8C24Xw=
 =o5Xl
 -----END PGP SIGNATURE-----

Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: global cleanups" from Arnd Bergmann:
 "Quite a bit of code gets removed, and some stuff moved around, mostly
  the old samsung s3c24xx stuff.  There should be no functional changes
  in this series otherwise.  Some cleanups have dependencies on other
  arm-soc branches and will be sent in the second round.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial conflicts mainly due to #include's being changes on
both sides.

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
  ep93xx: Remove unnecessary includes of ep93xx-regs.h
  ep93xx: Move EP93XX_SYSCON defines to SoC private header
  ep93xx: Move crunch code to mach-ep93xx directory
  ep93xx: Make syscon access functions private to SoC
  ep93xx: Configure GPIO ports in core code
  ep93xx: Move peripheral defines to local SoC header
  ep93xx: Convert the watchdog driver into a platform device.
  ep93xx: Use ioremap for backlight driver
  ep93xx: Move GPIO defines to gpio-ep93xx.h
  ep93xx: Don't use system controller defines in audio drivers
  ep93xx: Move PHYS_BASE defines to local SoC header file
  ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
  ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
  PM / devfreq: update the name of EXYNOS clock registers that were omitted
  PM / devfreq: update the name of EXYNOS clock register
  ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
  ARM: EXYNOS: use static declaration on regarding clock
  ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
  ARM: OMAP2+: Fix build error after merge
  ARM: S3C24XX: remove call to s3c24xx_setup_clocks
  ...
2012-03-27 16:03:32 -07:00
Linus Torvalds
250f6715a4 The following text was taken from the original review request:
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
 		https://lkml.org/lkml/2012/3/4/159
 --
 
 Nearly every subsystem has some kind of header with a proto like:
 
 	void foo(struct device *dev);
 
 and yet there is no reason for most of these guys to care about the
 sub fields within the device struct.  This allows us to significantly
 reduce the scope of headers including headers.  For this instance, a
 reduction of about 40% is achieved by replacing the include with the
 simple fact that the device is some kind of a struct.
 
 Unlike the much larger module.h cleanup, this one is simply two
 commits.  One to fix the implicit <linux/device.h> users, and then
 one to delete the device.h includes from the linux/include/ dir
 wherever possible.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPbNxLAAoJEOvOhAQsB9HWR6QQAMRUZ94O2069/nW9h4TO/xTr
 Hq/80lo/TBBiRmob3iWBP76lzgeeMPPVEX1I6N7YYlhL3IL7HsaJH1DvpIPPHXQP
 GFKcBsZ5ZLV8c4CBDSr+/HFNdhXc0bw0awBjBvR7gAsWuZpNFn4WbhizJi4vWAoE
 4ydhPu55G1G8TkBtYLJQ8xavxsmiNBSDhd2i+0vn6EVpgmXynjOMG8qXyaS97Jvg
 pZLwnN5Wu21coj6+xH3QUKCl1mJ+KGyamWX5gFBVIfsDB3k5H4neijVm7t1en4b0
 cWxmXeR/JE3VLEl/17yN2dodD8qw1QzmTWzz1vmwJl2zK+rRRAByBrL0DP7QCwCZ
 ppeJbdhkMBwqjtknwrmMwsuAzUdJd79GXA+6Vm+xSEkr6FEPK1M0kGbvaqV9Usgd
 ohMewewbO6ddgR9eF7Kw2FAwo0hwkPNEplXIym9rZzFG1h+T0STGSHvkn7LV765E
 ul1FapSV3GCxEVRwWTwD28FLU2+0zlkOZ5sxXwNPTT96cNmW+R7TGuslZKNaMNjX
 q7eBZxo8DtVt/jqJTntR8bs8052c8g1Ac1IKmlW8VSmFwT1M6VBGRn1/JWAhuUgv
 dBK/FF+I1GJTAJWIhaFcKXLHvmV9uhS6JaIhLMDOetoOkpqSptJ42hDG+89WkFRk
 o55GQ5TFdoOpqxVzGbvE
 =3j4+
 -----END PGP SIGNATURE-----

Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux

Pull <linux/device.h> avoidance patches from Paul Gortmaker:
 "Nearly every subsystem has some kind of header with a proto like:

	void foo(struct device *dev);

  and yet there is no reason for most of these guys to care about the
  sub fields within the device struct.  This allows us to significantly
  reduce the scope of headers including headers.  For this instance, a
  reduction of about 40% is achieved by replacing the include with the
  simple fact that the device is some kind of a struct.

  Unlike the much larger module.h cleanup, this one is simply two
  commits.  One to fix the implicit <linux/device.h> users, and then one
  to delete the device.h includes from the linux/include/ dir wherever
  possible."

* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  device.h: audit and cleanup users in main include dir
  device.h: cleanup users outside of linux/include (C files)
2012-03-24 10:41:37 -07:00
Paul Gortmaker
313162d0b8 device.h: audit and cleanup users in main include dir
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.

Clean up the users as follows:

1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.

2) For headers not really using anything from device.h, simply
delete the include altogether.

3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h

4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).

Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.

Total removals from #1 and #2: 51.  Total additions coming
from #3: 9.  Total other implicit dependencies from #4: 7.

As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-03-16 10:38:24 -04:00
Andrew Lunn
d34b7d4523 ARM: orion: spi: remove enable_clock_fix which is not used
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-16 04:28:40 +00:00
Kuninori Morimoto
49e599b859 spi: sh-hspi: control spi clock more correctly
Current sh-hspi had used platform-specific speed.
This patch remove it, and use spi_transfer specific speed.
It removes unnecessary flags from struct sh_hspi_info,
but struct sh_hspi_info is still exist, since sh-hspi needs
platform info in the future.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-15 03:41:01 -06:00
Shubhrajyoti D
8f53602be5 spi: Trivial warning fix
The loop count i traverses for ntrans which is unsigned
so make the loop count i also unsigned.

Fix the below warning
In file included from drivers/spi/spi-omap2-mcspi.c:38:
include/linux/spi/spi.h: In function 'spi_message_alloc':
include/linux/spi/spi.h:556: warning: comparison between signed and unsigned integer expressions

Cc: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-09 10:56:10 -07:00
Kuninori Morimoto
d1c8bbd793 spi: Add SuperH HSPI prototype driver
This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-09 09:50:09 -07:00
Linus Walleij
ffbbdd2132 spi: create a message queueing infrastructure
This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.

Most of the design is described in the documentation changes that
are included in this patch.

Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().

ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
  at all, instead be more agressive and have it as part of the
  compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
  deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
  Chris Blair.

Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-07 19:19:48 -07:00
Heiko Stuebner
f35ef7cab2 ARM: S3C24XX: move spi-s3c24xx platdata out of mach
spi.h now only contains the definition of the platform data structure
for the driver in spi-s3c24xx.c . Therefore it does not need to stay
in include/mach but can instead live in linux/spi/s3c24xx.h .

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-01-31 20:06:27 +09:00
Lars-Peter Clausen
3acbb0142d SPI: Add helper macro for spi_driver boilerplate
This patch introduces the module_spi_driver macro which is a convenience macro
for SPI driver modules similar to module_platform_driver. It is intended to be
used by drivers which init/exit section does nothing but register/unregister
the SPI driver. By using this macro it is possible to eliminate a few lines of
boilerplate code per SPI driver.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-17 12:15:39 -08:00
Mark Brown
0556dc340e backlight: fix broken regulator API usage in l4f00242t03
The regulator support in the l4f00242t03 is very non-idiomatic.  Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data.  The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.

Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver.  As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.

The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-10-31 17:30:54 -07:00
Peter Korsgaard
1bb6f9b042 mcp23s08: get rid of setup/teardown callbacks
There's no in-tree users, and bus notifiers are more generic anyway.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-15 13:54:17 -06:00
H Hartley Sweeten
a3cc68c378 gpio/74x164: remove unnecessary defines and prototype
Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious.  Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.

Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-06-03 12:14:16 -06:00
Linus Torvalds
20e0ec119b Merge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
  spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe fails
  spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in s3c24xx_spi_remove
  spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in nuc900_spi_remove
  spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()
  spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path
  spi: Use void pointers for data in simple SPI I/O operations
  spi/pl022: use cpu_relax in the busy loop
  spi/pl022: mark driver non-experimental
  spi/pl022: timeout on polled transfer v2
  spi/dw_spi: improve the interrupt mode with the batch ops
  spi/dw_spi: change poll mode transfer from byte ops to batch ops
  spi/dw_spi: remove the un-necessary flush()
  spi/dw_spi: unify the low level read/write routines
2011-05-26 12:13:22 -07:00
Mark Brown
0c4a159018 spi: Use void pointers for data in simple SPI I/O operations
Currently the simple SPI I/O operations all take pointers to u8 * buffers
to operate on. This creates needless type compatibility issues and the
underlying spi_transfer structure uses void pointers anyway so convert the
API over to take void pointers too.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-20 00:43:07 -06:00
Alexander Stein
ebcaaad9d5 Input: ads7846 - add possibility to use external vref on ads7846
Just set vref_mv in your platform config to use external vref. Otherwise
the internal one is used.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2011-05-12 08:28:56 -07:00
Lucas De Marchi
25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Linus Torvalds
a952baa034 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
  Input: tsc2005 - remove 'disable' sysfs attribute
  Input: tsc2005 - add open/close
  Input: tsc2005 - handle read errors from SPI layer
  Input: tsc2005 - do not rearm timer in hardirq handler
  Input: tsc2005 - don't use work for 'pen up' handling
  Input: tsc2005 - do not use 0 in place of NULL
  Input: tsc2005 - use true/false for boolean variables
  Input: tsc2005 - hide selftest attribute if we can't reset
  Input: tsc2005 - rework driver initialization code
  Input: tsc2005 - set up bus type in input device
  Input: tsc2005 - set up parent device
  Input: tsc2005 - clear driver data after unbinding
  Input: tsc2005 - add module description
  Input: tsc2005 - remove driver banner message
  Input: tsc2005 - remove incorrect module alias
  Input: tsc2005 - convert to using dev_pm_ops
  Input: tsc2005 - use spi_get/set_drvdata()
  Input: introduce tsc2005 driver
  Input: xen-kbdfront - move to drivers/input/misc
  Input: xen-kbdfront - add grant reference for shared page
  ...
2011-03-19 22:27:06 -07:00
Grant Likely
568a60eda2 spi/dw_spi: move dw_spi.h into drivers/spi
include/linux/dw_spi.h only includes driver internal data.  It doesn't
expose a platform_data configuration structure or similar (at least
nothing in-tree).  This patch moves the header into drivers/spi so
that the scope is limited to only the dw_spi_*.c driver files

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Feng Tang <feng.tang@intel.com>
Cc: spi-devel-general@lists.sourceforge.net
2011-03-18 10:26:52 -06:00
Jiri Slaby
46165a3d00 spi/dw_spi: Fix missing header
Currently, build on PPC dies with:
In file included from drivers/spi/dw_spi_mmio.c:16:
include/linux/spi/dw_spi.h:147: error: field ‘tx_sgl’ has incomplete type
include/linux/spi/dw_spi.h:149: error: field ‘rx_sgl’ has incomplete type

Add linux/scatterlist.h include to dw_spi.h, because we need to know
the contents of the structure.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-03-18 09:50:50 -06:00
Grant Likely
2dd2299767 Merge remote-tracking branch 'origin' into spi/next
Pull in Linus' tree to pick up changes required for the langwell gpio fixes
2011-03-17 13:48:06 -06:00
Dmitry Torokhov
def179c271 Merge branch 'tsc2005' into next 2011-03-16 23:29:56 -07:00
Lauri Leukkunen
37bd44694c Input: introduce tsc2005 driver
Discussions:

http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26748.html

Introduce a driver for the Texas Instruments TSC2005 touchscreen
controller (http://focus.ti.com/docs/prod/folders/print/tsc2005.html).

The patch is based on a driver by Lauri Leukkunen, with modifications
by David Brownell, Phil Carmody, Imre Deak, Hiroshi DOYU, Ari Kauppi,
Tony Lindgren, Jarkko Nikula, Eero Nurkkala and Roman Tereshonkov.

Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
[aaro.koskinen@nokia.com: patch description, rebasing & cleanup]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[ext-srikar.1.bhavanarayana@nokia.com: various fixes]
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2011-03-16 23:27:39 -07:00
Peter Korsgaard
0b7bb77fd5 gpio/mcp23s08: support mcp23s17 variant
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.

The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-03-12 01:26:34 -07:00
Thomas Chou
ce792580ea spi: add OpenCores tiny SPI driver
This patch adds support of OpenCores tiny SPI driver.

http://opencores.org/project,tiny_spi

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-22 14:59:53 -07:00
Russ Gorby
2f1522eccb serial: ifx6x60: expanded info available from platform data
Some platform attributes (e.g. max_hz, use_dma) were being intuited
from the modem type. These things should be specified by the platform
data.

Added max_hz, use_dma to ifx_modem_platform_data definition,
replaced is_6160 w/ modem_type, and changed clients accordingly

Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-03 11:43:10 -08:00
Linus Torvalds
021db8e2bd Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
  spi/omap: Fix DMA API usage in OMAP MCSPI driver
  spi/imx: correct the test on platform_get_irq() return value
  spi/topcliff: Typo fix threhold to threshold
  spi/dw_spi Typo change diable to disable.
  spi/fsl_espi: change the read behaviour of the SPIRF
  spi/mpc52xx-psc-spi: move probe/remove to proper sections
  spi/dw_spi: add DMA support
  spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
  spi/dw_spi: Fix too short timeout in spi polling loop
  spi/pl022: convert running variable
  spi/pl022: convert busy flag to a bool
  spi/pl022: pass the returned sglen to the DMA engine
  spi/pl022: map the buffers on the DMA engine
  spi/topcliff_pch: Fix data transfer issue
  spi/imx: remove autodetection
  spi/pxa2xx: pass of_node to spi device and set a parent device
  spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
  spi/pxa2xx: Add chipselect support for Sodaville
  spi/pxa2xx: Consider CE4100's FIFO depth
  spi/pxa2xx: Add CE4100 support
  ...
2011-01-07 17:08:46 -08:00
Grant Likely
94a544a4e8 Merge branch 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
  spi/pxa2xx: register driver properly
  spi/pxa2xx: add support for shared IRQ handler
  spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
  arm/pxa2xx: reorgazine SSP and SPI header files
  spi/pxa2xx: Add CE4100 support
  spi/pxa2xx: Consider CE4100's FIFO depth
  spi/pxa2xx: Add chipselect support for Sodaville
  spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
  spi/pxa2xx: pass of_node to spi device and set a parent device
2010-12-29 01:05:50 -07:00
Feng Tang
7063c0d942 spi/dw_spi: add DMA support
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms

It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled

Also change the dma interface suggested by Linus Walleij.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:23:25 -07:00
Sebastian Andrzej Siewior
d6ea3df0d4 spi/pxa2xx: Add CE4100 support
Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 13:48:30 +01:00
Sebastian Andrzej Siewior
8348c259dd arm/pxa2xx: reorgazine SSP and SPI header files
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.

This move got verified by building the following defconfigs:
   cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
   imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
   raumfeld_defconfig magician_defconfig

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 12:18:33 +01:00
Russ Gorby
af3b8881f4 ifx6x60: SPI protocol driver for Infineon 6x60 modem
Prototype driver for the IFX6x60 series of SPI attached modems by Jim
Stanley and Russ Gorby

Signed-off-by: Russ Gorby <richardx.r.gorby@intel.com>

[Some reworking and a major cleanup]

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-11-11 11:35:57 -08:00
Linus Torvalds
90ae83f7fc Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: fix erroneous platform data in U300
  spi: fixed odd static string conventions in core code
  spi/bfin_spi: only request GPIO on first load
  spi/bfin_spi: handle error/status changes after data interrupts
  spi: enable spi_board_info to be registered after spi_master
2010-11-01 07:50:43 -04:00
Miguel Gaio
ead6db0843 gpio: add support for 74x164 serial-in/parallel-out 8-bit shift register
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register.  This driver can be used as a GPIO output expander.

[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-10-27 18:03:07 -07:00
Feng Tang
2b9603a0d7 spi: enable spi_board_info to be registered after spi_master
Currently spi_register_board_info() has to be called before its related
spi_master be registered, otherwise these board info will be just ignored.

This patch will remove this order limit, it adds a global spi master list
like the existing global board info listr. Whenever a board info or a
spi_master is registered, the spi master list or board info list
will be scanned, and a new spi device will be created if there is a
master-board info match.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-21 23:52:16 -06:00
David S. Miller
69259abb64 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/pcmcia/pcnet_cs.c
	net/caif/caif_socket.c
2010-10-06 19:39:31 -07:00
John W. Linville
b618f6f885 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	arch/arm/mach-omap2/board-omap3pandora.c
	drivers/net/wireless/ath/ath5k/base.c
2010-09-21 15:49:14 -04:00
Ohad Ben-Cohen
c1f9a09560 wl12xx: make wl12xx.h common to both spi and sdio
Move wl12xx.h outside of the spi-specific location,
so it can be shared with both spi and sdio solutions.

Update all users of spi/wl12xx.h accordingly

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-21 11:04:38 -04:00
David S. Miller
e548833df8 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/mac80211/main.c
2010-09-09 22:27:33 -07:00
Feng Tang
e3e55ff585 spi/dw_spi: clean the cs_control code
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-09-08 10:50:00 -06:00
John W. Linville
78ab952717 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem 2010-09-02 13:30:07 -04:00
Kalle Valo
4c5f7d7a1e wl12xx: change contact person for the include file
Luciano should be the contact person for the include/linux/spi/wl12xx.h file.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-25 14:33:19 -04:00
Ernst Schwab
5c79a5ae23 spi.h: missing kernel-doc notation, please fix
Added comments in kernel-doc notation for previously added struct fields.

Signed-off-by: Ernst Schwab <eschwab@online.de>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-08-17 22:55:38 -06:00
Linus Torvalds
b171aa2770 Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/amba_pl022: Fix probe and remove hook section annotations.
  spi/mpc5121: change annotations for probe and remove functions
  spi/bitbang: reinitialize transfer parameters for every message
  spi/spi-gpio: add support for controllers without MISO or MOSI pin
  spi/bitbang: add support for SPI_MASTER_NO_{TX, RX} modes
  SPI100k: Fix 8-bit and RX-only transfers
  spi/mmc_spi: mmc_spi adaptations for SPI bus locking API
  spi/mmc_spi: SPI bus locking API, using mutex

Fix trivial conflict in drivers/spi/mpc512x_psc_spi.c due to 'struct
of_device' => 'struct platform_device' rename and __init/__exit to
__devinit/__devexit fix.
2010-08-14 11:54:09 -07:00
Marc Kleine-Budde
4a22b8a4ad gpio: max730x: make pullups configurable via platformdata
The gpios on the max730x chips have support for internal pullups while in
input mode.

This patch adds support for configuring these pullups via platform data.
A new member ("input_pullup_active") to the platform data struct is
introduced.  A set bit in this variable activates the pullups while the
respective port is in input mode.  This is a compatible enhancement since
unset bits lead to disables pullups which was the default in the original
driver.

_Note_: the 4 lowest bits in "input_pullup_active" are unused because the
first 4 ports of the controller are not used, too.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 08:59:08 -07:00
Marek Szyprowski
3c8e1a84fd spi/spi-gpio: add support for controllers without MISO or MOSI pin
There are some boards that do not strictly follow SPI standard and use
only 3 wires (SCLK, MOSI or MISO, SS) for connecting some simple auxiliary
chips and controls them with GPIO based 'spi controller'. In this
configuration the MISO or MOSI line is missing (it is not required if the
chip does not transfer any data back to host or host only reads data from
chip).

This patch adds support for such non-standard configuration in GPIO-based
SPI controller. It has been tested in configuration without MISO pin.

Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-07-03 22:45:44 -06:00
Dmitry Torokhov
0f622bf465 Input: ads7846 - do not allow altering platform data
Tested-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-07-03 13:13:22 -07:00
Ernst Schwab
cf32b71e98 spi/mmc_spi: SPI bus locking API, using mutex
SPI bus locking API to allow exclusive access to the SPI bus, especially, but
not limited to, for the mmc_spi driver.

Coded according to an outline from Grant Likely; here is his
specification (accidentally swapped function names corrected):

It requires 3 things to be added to struct spi_master.
- 1 Mutex
- 1 spin lock
- 1 flag.

The mutex protects spi_sync, and provides sleeping "for free"
The spinlock protects the atomic spi_async call.
The flag is set when the lock is obtained, and checked while holding
the spinlock in spi_async().  If the flag is checked, then spi_async()
must fail immediately.

The current runtime API looks like this:
spi_async(struct spi_device*, struct spi_message*);
spi_sync(struct spi_device*, struct spi_message*);

The API needs to be extended to this:
spi_async(struct spi_device*, struct spi_message*)
spi_sync(struct spi_device*, struct spi_message*)
spi_bus_lock(struct spi_master*)  /* although struct spi_device* might
be easier */
spi_bus_unlock(struct spi_master*)
spi_async_locked(struct spi_device*, struct spi_message*)
spi_sync_locked(struct spi_device*, struct spi_message*)

Drivers can only call the last two if they already hold the spi_master_lock().

spi_bus_lock() obtains the mutex, obtains the spin lock, sets the
flag, and releases the spin lock before returning.  It doesn't even
need to sleep while waiting for "in-flight" spi_transactions to
complete because its purpose is to guarantee no additional
transactions are added.  It does not guarantee that the bus is idle.

spi_bus_unlock() clears the flag and releases the mutex, which will
wake up any waiters.

The difference between spi_async() and spi_async_locked() is that the
locked version bypasses the check of the lock flag.  Both versions
need to obtain the spinlock.

The difference between spi_sync() and spi_sync_locked() is that
spi_sync() must hold the mutex while enqueuing a new transfer.
spi_sync_locked() doesn't because the mutex is already held.  Note
however that spi_sync must *not* continue to hold the mutex while
waiting for the transfer to complete, otherwise only one transfer
could be queued up at a time!

Almost no code needs to be written.  The current spi_async() and
spi_sync() can probably be renamed to __spi_async() and __spi_sync()
so that spi_async(), spi_sync(), spi_async_locked() and
spi_sync_locked() can just become wrappers around the common code.

spi_sync() is protected by a mutex because it can sleep
spi_async() needs to be protected with a flag and a spinlock because
it can be called atomically and must not sleep

Signed-off-by: Ernst Schwab <eschwab@online.de>
[grant.likely@secretlab.ca: use spin_lock_irqsave()]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
2010-06-28 17:49:29 -07:00
Anatolij Gustschin
7804302b14 Input: ads7846 - allow specifying irq trigger type in platform data
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.

Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-06-28 01:34:25 -07:00
Grant Likely
b1e50ebcf2 Merge remote branch 'origin' into secretlab/next-spi 2010-05-25 00:38:26 -06:00
hartleys
41c4221ca6 spi: move bitbang txrx utility functions to private header
A number of files in drivers/spi fail checkincludes.pl due to the double
include of <linux/spi/spi_bitbang.h>.

The first include is needed to get the struct spi_bitbang definition and
the spi_bitbang_* function prototypes.

The second include happens after defining EXPAND_BITBANG_TXRX to get the
inlined bitbang_txrx_* utility functions.

The <linux/spi/spi_bitbang.h> header is also included by a number of other
spi drivers, as well as some arch/ code, in order to use struct spi_bitbang
and the associated functions.

To fix the double include, and remove any potential confusion about it, move
the inlined bitbang_txrx_* functions to a new private header in drivers/spi
and also remove the need to define EXPAND_BITBANG_TXRX.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-25 00:23:17 -06:00
John W. Linville
3b51cc996e Merge branch 'master' into for-davem
Conflicts:
	drivers/net/wireless/ath/ath9k/phy.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-debugfs.c
2010-04-23 14:43:45 -04:00
Grazvydas Ignotas
a02a295680 wl1251: add support for dedicated IRQ line
wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.

Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16 15:47:14 -04:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Alberto Panizzo
e7fb9c4ad3 backlight: Add Epson L4F00242T03 LCD driver
The Epson LCD L4F00242T03 is mounted on the Freescale i.MX31 PDK board. 
Based upon Marek Vasut work in l4f00242t03.c, this driver provides
basic init and power on/off functionality for this device through the
sysfs lcd interface.

Unfortunately Datasheet for this device are not available and
all the control sequences sent to the display were copied from the
freescale driver that in the i.MX31 Linux BSP.

As in the i.MX31PDK board the core and io suppliers are voltage
regulators, that functionality is embedded here, but not strict.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
2010-03-16 19:47:53 +00:00
Ranjith Lohithakshan
fdba2bb1f2 Input: ads7846 - add wakeup support
Add wakeup support to the ads7846 driver. Platforms can enable wakeup
capability by setting the wakeup flag in ads7846_platform_data. With this
patch the ads7846 driver can be used to wake the system from suspend.

Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-03-11 00:02:43 -08:00
Michael Hennerich
06a09124b5 Input: ads7846 - add support for AD7843 parts
The AD7873 is almost identical to the ADS7846; the only difference is
related to the Power Management bits PD0 and PD1.  This results in a
slightly different PENIRQ enable behavior.  For the AD7873, VREF should
be turned off during differential measurements.

So, add the AD7873/43 to the list of driver supported devices, and prevent
VREF usage during differential/ratiometric conversion modes.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-03-09 22:12:45 -08:00
Wolfram Sang
e952805d2d gpio: add driver for MAX7300 I2C GPIO extender
Add the MAX7300-I2C variant of the MAX7301-SPI version.  Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part.  The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:48 -08:00
Grant Likely
fb7899b1f0 Merge commit 'v2.6.33-rc6' into secretlab/next-spi 2010-02-02 01:05:22 -07:00
Linus Torvalds
499a267371 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: update multi-touch protocol documentation
  Input: add the ABS_MT_PRESSURE event
  Input: winbond-cir - remove dmesg spam
  Input: lifebook - add another Lifebook DMI signature
  Input: ad7879 - support auxiliary GPIOs via gpiolib
2010-01-29 11:15:32 -08:00
George Shore
83fe518a83 spi/dw_spi: enable platform specific chipselect.
The driver core allows for a platform-specific chipselect assert/deassert
function, however the chipselect function in the core doesn't take advantage
of this fact.

This enables the use of a custom function, should it be defined.

Signed-off-by: George Shore <george@georgeshore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-21 07:24:29 -07:00