[Description]
The spec does not allow POST_LT_ADJ_GRANTED to be set when TPS4 is used.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We incorrectly began powering down the display at boot/resume whenever
fast boot was not possible. This should not be done in the case where there
exists a stream for the eDP since this implies that we want to turn it on.
[How]
Add check for eDP stream to decide whether to power off edp.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
By the time output csc matrix is being programmed, stream connection to
OPP has been established, but this information has not been relayed back
to HUBP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our existing logic in deciding whether to use RAM or ROM
depends on whether we are dealing with an identity gamma ramp.
[How]
In addition to the is_identity flag
a new is_logical_identity flag has been
added. The is_identity flag now denotes
whether the OS gamma is an RGB256 identity
and the new logical identity will inidicate
that the given gamma ramp regardless of its
type is identity.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. This makes it
difficult to use vmid use with external components.
This change moves vmid logic outside dc and allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBios sometimes reports incorrect object type as encoder instead of
connector
[How]
Change error message to debug message
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are no longer needed, Also added RESERVED bits.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using this logic breaks driver unload, this is a temporary fix
a followup patch will properly fix this
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD not going to be high if Panel VDD is off
And all AUX transaction will fail :(
[How]
1. Power on VDD before attempting detection if it isn't already on
2. Improve the robustness by having a retry mechanism on the
first DPCD read after VDD on. If a particular board always holds
HPD high incorrectly, the AUX access may fail, so we can retry
in those scenarios. This change would only improve logic
since it prevents AUX failure leading to bad resolution on internal
panel.
3. We should never need to re-detect internal panel, so logic
is re-arranged a bit to skip earlier.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Add i2c_hw_Status check to make sure when HW i2c is in use.
2. Don't reset HW engine in is_hw_busy() and instead do this in
process_transaction() because SW i2c does not check if hw i2c is in use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to assert just return
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some panels return a link rate of 0 (unknown) in DPCD 0. In this case,
an appropriate mode cannot be set, and certain panels will show
corruption as they are forced to use a mode they do not support.
[HOW]
Read DPCD 10 in the case where supported link rate from DPCD 0 is
unknown, and pass that value on to the reported link rate.
This re-introduces behaviour present in previous versions that appears
to have been accidentally removed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.
[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.
It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.
It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's non trivial to configure or specify an ABM reduction level for
userspace outside of X. There is also no method to specify the default
ABM value at boot time.
A parameter should be added to configure this.
[How]
Expose a module parameter that can specify the default ABM level to
use for eDP connectors on DC enabled hardware that loads the DMCU
firmware.
The default is still disabled (0), but levels can range from 1-4. Levels
control how much the backlight can be reduced, with being the least
amount of reduction and four being the most reduction.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's incorrect to do soft reset for SRIOV, when GFX
hang the WREG would stuck there becuase it goes KIQ way.
the GPU reset counter is incorrect: always increase twice
for each timedout
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since Hardware bug, GDS exist ECC error after cold boot up,
adding GDS clearing workaround in later init for gfx9.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.
Poor performance and stuttering can occur when many of these commits
are frequently issued.
This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.
[How]
Drop the check for state->allow_modeset in should_reset_plane.
All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC
These conditions are all covered in should_reset_plane.
We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.
But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.
[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.
Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This option is no longer needed. The default code paths
are now the only option.
v2: Add HPAGE support and a default for non contiguous maps
v3: Misread 512 pages as MiB ...
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use SMU firmware version to indentify the raven1 refresh device and
then load homologous RLC FW.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Suggested-by: Huang Rui<Ray.Huang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add gfxoff_state_changed_by_workload to control gfxoff
when set power_profile_mode
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under Vega10 SR-IOV VF, L1 register access mode should be enabled by
default as the non-security VF will no longer be supported.
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ported from gfx8, no changes in register setup.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Translate queue priority into pipe priority and write to MQDs.
The priority values are used to perform queue and pipe arbitration.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always mark evicted queues with q->properties.is_evicted = true, even
queues that are inactive for other reason. This simplifies maintaining
the eviction state as it doesn't require updating is_evicted when other
queue activation conditions change.
On the other hand, we now need to check those other queue activation
conditions whenever an evicted queues is restored. To minimize code
duplication, move the queue activation check into a macro so it can be
maintained in one central place.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Cox <Philip.Cox@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
EDC counts are related to instance and se. They are not the same
for different type of EDC. EDC clearing are changed to base on
individual EDC's instance and SE number.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.
This caused numerous regressions on DCN1_01 when loading the driver.
[How]
Add it back.
Fixes: 97df424fe7 ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This avoids OOM situations when we have lots of threads
submitting at the same time.
v3: apply this to the whole driver, not just CS
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And only move them in on validation. This allows for better control
when multiple processes are fighting over those resources.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The messages about amdgpu_cs_list_validate are duplicated because the
caller will complain into the logs as well and we can also get
interrupted by a signal here.
Also fix the the caller to not report -EAGAIN from validation.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras ta interface header need to be updated to match with latest ta fw updates
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds the required infrastructure for manually updated displays,
such as DSI command mode panels. While those panels often support
partial updates we currently always do a full refresh.
The display will be refreshed when something calls the dirty callback,
such as libdrm's drmModeDirtyFB(). This is currently being done at least
by the kernel console and Xorg (with modesetting driver) in their
default configuration. Weston does not implement this and the fbdev
backend does not work (display will not update). Weston's DRM backend
uses double buffering and the page flip will also trigger a display
refresh.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This prepares framedone interrupt handling for
manual display update support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While most display types only forward their VM to the DISPC, this
is not true for DSI. DSI calculates the VM for DISPC based on its
own, but it's not identical. Actually the DSI VM is not even a valid
DISPC VM making this check fail. Let's restore the old behaviour
and avoid checking the DISPC VM for DSI here.
Fixes: 7c27fa57ef ("drm/omap: Call dispc timings check operation directly")
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This macro is only used by omapdrm, which should print
debug messages using the DRIVER category instead of the
default CORE category.
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Using dev_get_drvdata directly.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for the DRM_FORMAT_RGBA5551, DRM_FORMAT_RGBX5551,
DRM_FORMAT_ABGR1555, DRM_FORMAT_XBGR1555, DRM_FORMAT_BGRA5551 and
DRM_FORMAT_BGRX5551 formats to the DU driver. Those formats are only
available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Add support for the DRM_FORMAT_RGBA4444, DRM_FORMAT_RGBX4444,
DRM_FORMAT_ABGR4444, DRM_FORMAT_XBGR4444, DRM_FORMAT_BGRA4444 and
DRM_FORMAT_BGRX4444 formats to the DU driver. Those formats are only
available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Add support for the DRM_FORMAT_RGBA8888, DRM_FORMAT_RGBX8888,
DRM_FORMAT_ABGR8888 and DRM_FORMAT_XBGR8888 formats to the DU driver.
Those formats are only available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
In dual-link LVDS mode, the LVDS1 encoder is used as a companion for
LVDS0, and both encoders transmit data from DU0. The LVDS1 output of DU1
can't be used in that case, don't create an encoder and connector for
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
In dual-link mode the LVDS0 encoder transmits even-numbered pixels, and
sends odd-numbered pixels to the LVDS1 encoder for transmission on a
separate link.
To implement support for this mode of operation, determine if the LVDS
connection operates in dual-link mode by querying the next device in the
pipeline, locate the companion encoder, and control it directly through
its bridge operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The DRM core and DU driver guarantee that the LVDS bridge will not be
double-enabled or double-disabled. Remove the corresponding unnecessary
checks.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Set a drm_bridge_timings in the drm_bridge, and use it to report the
input bus mode (single-link or dual-link). The other fields of the
timings structure are kept to 0 as they do not apply to LVDS buses.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The new writeback feature exports functions so that they can integrate
into the rcar_du_kms module.
The interface functions are defined in the rcar_du_writeback header, but
it is not included in the object file itself leading to compiler
warnings for missing prototypes.
Include the header as appropriate.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The LVDS encoders on RZ/G2M SoC is similar to R-Car M3-W. Add support for
RZ/G2M (R8A774A1) SoC to the LVDS encoder driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for the R8A774A1 DU (which is very similar to the R8A7796 DU
except that it lacks TCON and CMM); it has one RGB output, one LVDS output
and one HDMI output.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split late_init into two functions, one (do_late_init) which
just does the hw init, and late_init which calls do_late_init
and schedules the IB test work. Call do_late_init in
the GPU reset code to run the init code, but not schedule
the IB test code. The IB test code is called directly
in the gpu reset code so no need to run the IB tests
in a separate work thread. If we do, we end up racing.
v2: Rework late_init. Pull out the mgpu fan boost and xgmi
pstate code into late_init so they get called in all cases.
rename the late_init worker thread to delayed work since it's
just the IB tests now which can happen later. Schedule the
work at init and resume time. It's not needed at reset time
because the IB tests are called directly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gpu reset will run late_init and schedule the late_init_work. if we
keep triggering gpu reset in a short time, there are potenial races.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
-----BEGIN PGP SIGNATURE-----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=GrAP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
For SAM9X60 SoC, sys_clk is through lcd_gclk clock source and this
needs to be enabled before enabling lcd_clk.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[claudiu.beznea@microchip.com: add fixed_clksrc checks]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-5-git-send-email-claudiu.beznea@microchip.com
SAM9x60 LCD Controller has no option to select clock source as previous
controllers have. To be able to use the same driver even for this LCD
controller add a config option to know if controller supports this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-2-git-send-email-claudiu.beznea@microchip.com
Fixes the following warnings:
./include/drm/drm_mode_config.h:841: warning: Incorrect use of
kernel-doc format: * hdr_output_metadata_property: Connector
property containing hdr
./include/drm/drm_mode_config.h:918: warning: Function parameter or member 'hdr_output_metadata_property' not described in 'drm_mode_config'
./include/drm/drm_connector.h:1251: warning: Function parameter or member 'hdr_output_metadata' not described in 'drm_connector'
./include/drm/drm_connector.h:1251: warning: Function parameter or member 'hdr_sink_metadata' not described in 'drm_connector'
Also adds some property documentation for HDR Metadata Connector
Property in connector property create function.
v2: Fixed Sean Paul's review comments.
v3: Fixed Daniel Vetter's review comments, added the UAPI structure
definition section in kernel docs.
v4: Fixed Daniel Vetter's review comments.
v5: Added structure member references as per Daniel's suggestion.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: "Ville Syrjä" <ville.syrjala@linux.intel.com>
Cc: Hans Verkuil <hansverk@cisco.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Reviewed-by: Sean Paul <sean@poorly.run> (v1)
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
[danvet: Fix up markup: () for functions, & for structs. Style guide
also recommends to prepend struct for structures.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1559647022-7336-1-git-send-email-uma.shankar@intel.com
struct drm_fb_helper_crtc is now just a wrapper around drm_mode_set so
use that directly instead and attach it as a modeset array onto
drm_client_dev. drm_fb_helper will use this array to store its modesets
which means it will always initialize a drm_client, but it will not
register the client (callbacks) unless it's the generic fbdev emulation.
Code will later be moved to drm_client, so add code there in a new file
drm_client_modeset.c with MIT license to match drm_fb_helper.c.
The modeset connector array size is hardcoded for the cloned case to avoid
having to pass in a value from the driver. A value of 8 is chosen to err
on the safe side. This means that the max connector argument for
drm_fb_helper_init() and drm_fb_helper_fbdev_setup() isn't used anymore,
a todo entry for this is added.
In pan_display_atomic() restore_fbdev_mode_force() is used instead of
restore_fbdev_mode_atomic() because that one will later become internal
to drm_client_modeset.
Locking order:
1. drm_fb_helper->lock
2. drm_master_internal_acquire
3. drm_client_dev->modeset_mutex
v6: Improve commit message (Sam Ravnborg)
v3:
- Use full drm_client_init/release for the modesets (Daniel Vetter)
- drm_client_for_each_modeset: use lockdep_assert_held (Daniel Vetter)
- Hook up to Documentation/gpu/drm-client.rst (Daniel Vetter)
v2:
- Add modesets array to drm_client (Daniel Vetter)
- Use a new file for the modeset code (Daniel Vetter)
- File has to be MIT licensed (Emmanuel Vadot)
- Add copyrights from drm_fb_helper.c
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190531140117.37751-3-noralf@tronnes.org
drm_atomic_set_fence_for_plane() contains the main discussion from a
driver pov, link to that from more places.
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603142848.26487-1-daniel.vetter@ffwll.ch
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BOs on the LRU might be blocked during command submission
and cause OOM situations.
Avoid this by blocking for the first busy BO not locked by
the same ticket as the BO we are searching space for.
v10: completely start over with the patch since we didn't
handled a whole bunch of corner cases.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move BOs which are currently in a lower domain to the new
LRU before allocating backing space while validating.
This makes sure that we always have enough entries on the
LRU to allow for other processes to wait for an operation
to complete.
v2: generalize the test
v3: fix rebase error
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We tried this once before, but that turned out to be more
complicated than thought. With all the right prerequisites
it looks like we can do this now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If drivers don't prefer a system memory placement
they should not but it into the placement list first.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When a signal arrives we should return immediately for
handling it and not try other placements first.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are already doing this for DMA-buf imports and also for
amdgpu VM BOs for quite a while now.
If this doesn't run into any problems we are probably going
to stop removing BOs from the LRU altogether.
v2: drop BUG_ON from ttm_bo_add_to_lru
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the VF, some registers only could be programmed with RLC.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.
[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.
[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.
[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.
[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
so that it is passed in by driver during DMCU initn
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.
Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.
[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.
If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] This is cause by failing to read link caps from driver.
Signed-off-by: Daniel He <daniel.he@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Value read from SMU is 16 bits, not 32.
[How]
Fix type, and add wm_type enum in preparation for future interfaces.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during It's possible to call dcn_validate_bandwidth with no plane.
In that case, as we are only intersted in if output timing is supported or not,
even if we cannot support native resolution, we still want to support lower
resolution if it is valid
[how]
if there exist no surface, make viewport/rec_out size at max 1080p. It is
already known that 1080p x 6(max # of pipes) is supported, so if we fail
validation, it is because of the stream
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
by adding fast_validate flag, we are skipping some portion of
dcn_validate_bandwidth code that is not necessary for mode validation.
However we have a bug where it does not calculate
v->total_data_read_bandwidth, which is one of the factors determines the
result of the validation, and therefore report false positive during
mode validation.
[how]
add calculation of v->total_data_read_bandwidth outside of the region
that is guarded by fast_validate flag
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add min_dcfclk_mhz to bounding box overrides.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Better organization
[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GSL is a form of locking that can be used to synchronize pipes in a
pipe-split configurations when async flip is used. Add the registers
here.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.
[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
stream id should uniquely identify an instance of stream.
the copy constructor should be treated as a new
stream instance.
[how]
assign a new stream id in this copy constructor.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D
(unless we know 1D LUT is identity), so we never want to return here early.
We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is
called near the end of that function.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.
[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As it will destroy clear_state_obj, and also will unpin it in the
gfx_v9_0_sw_fini, so don't need to
call amdgpu_bo_free_kernel in gfx_v9_0_sw_fini, or it will have unpin warning.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
injection need a valid gpu address.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement HDMI audio support by using ASoC HDMI codec. The commit
implements the necessary callbacks and configuration for the HDMI
codec and registers a virtual platform device for the codec to attach.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ef6895d016554b1e0c8b388d4993bcd6a3699341.1558964241.git.jsarha@ti.com
The pixel clock unit in the first two registers (0x00 and 0x01) of
sii9022 is 10kHz, not 1kHz as in struct drm_display_mode. Division by
10 fixes the issue.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1a2a8eae0b9d6333e7a5841026bf7fd65c9ccd09.1558964241.git.jsarha@ti.com
The driver always sets InputBusFmt:EDGE to 0 (falling edge).
Add drm_bridge_timings's input_bus_flags to reflect that the bridge
samples on falling edges.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/deb02a1fd508c514472a4e660092f301e6681361.1558964241.git.jsarha@ti.com
We need to know the link bandwidth to filter out modes we cannot
support, so we need to have read the display props before doing the
filtering.
To ensure we have up to date display props, call tc_get_display_props()
in the beginning of tc_connector_get_modes().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-22-tomi.valkeinen@ti.com
In tc_bridge_mode_set callback, we store the pointer to the given
drm_display_mode, and use the mode later. Storing a pointer in such a
way looks very suspicious to me, and I have observed odd issues where
the timings were apparently (at least mostly) zero.
Do a copy of the drm_display_mode instead to ensure we don't refer to
freed/modified data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-21-tomi.valkeinen@ti.com
drm_connector_helper_funcs.best_encoder is only needed when the
connector can have more than one encoder, and that is never the case
here.
So remove tc_connector_best_encoder.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-20-tomi.valkeinen@ti.com
We have tc_connector_mode_valid() to filter out videomdoes that the
tc358767 cannot support. As it is a bridge limitation, change the code
to use drm_bridge_funcs's mode_valid instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-19-tomi.valkeinen@ti.com
tc_main_link_enable() checks if videomode has been set, and fails if
there's no videomode. As tc_main_link_enable() no longer depends on the
videomode, we can drop the check.
Also, while tc_stream_enable() does depend on the videomode, we can
expect that a mode has been set before drm_bridge_funcs.enable is
called, so we don't need the check there either.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-18-tomi.valkeinen@ti.com
The current link training code does unnecessary retry-loops, and does
extra writes to the registers. It is easier to follow the flow and
ensure it's similar to Toshiba's documentation if we deal with LT inside
tc_main_link_enable() function.
This patch adds tc_wait_link_training() which handles waiting for the LT
phase to finish, and does the necessary LT register setups in
tc_main_link_enable, without extra loops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-17-tomi.valkeinen@ti.com
The driver has a loop after ending link training, where it reads the
DPCD link status and prints an error if that status is not ok.
The loop is unnecessary, as far as I can understand from DP specs, so
let's remove it. We can also print the more specific errors to help
debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-16-tomi.valkeinen@ti.com
At the end of the link training, two steps have to be taken: 1)
tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove
LT flag in DPCD 0x102.
Toshiba's documentation tells to first write the DPCD, then modify
DP0_SRCCTRL. In my testing this often causes issues, and the link
disconnects right after those steps.
If I reverse the steps, it works every time. There's a chance that this
is DP sink specific, though, but as my testing shows this sequence to be
much more reliable, let's change it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-15-tomi.valkeinen@ti.com
For some reason the driver has a msleep(100) after writing to
DP_PHY_CTRL. Toshiba's documentation doesn't suggest any delay is
needed, and I have not seen any issues with the sleep removed.
Drop it, as msleep(100) is a rather big one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-14-tomi.valkeinen@ti.com
Link training will sometimes fail if the DP link is enabled when
tc_main_link_enable() is called. The driver makes sure the DP link is
disabled when the DP output is disabled, and we never enable the DP
without first disabling it, so this should never happen.
However, as the HW behavior seems to be somewhat random if DP link has
erroneously been left enabled, let's add a WARN_ON() for the case and
set DP0CTL to 0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-13-tomi.valkeinen@ti.com
Currently the code writes 0 to DP0CTL in tc_stream_disable(), which
disables the whole DP link instead of just the video stream. We always
disable the link and the stream together from tc_bridge_disable(), so
this doesn't cause any issues.
Nevertheless, fix this by only clearing VID_EN in tc_stream_disable to
stop the video stream while keeping the link enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-12-tomi.valkeinen@ti.com
Currently we have tc_main_link_setup(), which configures and enabled the
link, but we have no counter-part for disabling the link.
Add tc_main_link_disable, and rename tc_main_link_setup to
tc_main_link_enable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-11-tomi.valkeinen@ti.com
We set up the PXL PLL inside tc_main_link_setup. This is unnecessary,
and makes tc_main_link_setup depend on the video-mode, which should not
be the case. As PXL PLL is used only for the video stream (and only when
using the HW test pattern), let's move the PXL PLL setup into
tc_stream_enable.
Also, currently the PXL PLL is only disabled if the driver if removed.
Let's disable the PXL PLL when the stream is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-10-tomi.valkeinen@ti.com
It is nicer to have enable/disable functions instead of set(bool enable)
style function.
Split tc_main_link_stream into tc_stream_enable and tc_stream_disable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-9-tomi.valkeinen@ti.com
The driver currently sets the video stream registers in
tc_main_link_setup. One should be able to establish the DP link without
any video stream, so a more logical place is to configure the stream in
the tc_main_link_stream. So move them there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-8-tomi.valkeinen@ti.com
The driver sets up AUX link at probe time, but, for some reason, also
sets the main link's number of lanes using tc->link.base.num_lanes. This
is not needed nor correct, as the number of lanes has not been decided
yet. The number of lanes will be set later during main link setup.
Modify aux_link_setup so that it does not use tc->link, and thus makes
aux setup independent of the link probing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-7-tomi.valkeinen@ti.com
swing and preemp fields are not used. Remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-6-tomi.valkeinen@ti.com
Minor cleanups:
- Use bool for boolean fields
- Use DP_MAX_DOWNSPREAD_0_5 instead of BIT(0)
- debug print down-spread and scrambler status
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-5-tomi.valkeinen@ti.com
DP always uses ANSI 8B10B encoding. Some monitors (old?) may not have
the ANSI 8B10B bit set in DPCD, even if it should always be set.
The tc358767 driver currently respects that flag, and turns the encoding
off if the monitor does not have the bit set, which then results in the
monitor not working.
This patch makes the driver to always use ANSI 8B10B encoding, and drops
the 'coding8b10b' field which is no longer used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-4-tomi.valkeinen@ti.com
We need to reset DPCD voltage-swing & pre-emphasis before starting the
link training, as otherwise tc358767 will use the previous values as
minimums.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-3-tomi.valkeinen@ti.com
tc_aux_get_status() does not report AUX_TIMEOUT correctly, as it only
checks the AUX_TIMEOUT if aux is still busy. Fix this by always checking
for AUX_TIMEOUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-2-tomi.valkeinen@ti.com
New stuff for 5.3:
- Add new thermal sensors for vega asics
- Various RAS fixes
- Add sysfs interface for memory interface utilization
- Use HMM rather than mmu notifier for user pages
- Expose xgmi topology via kfd
- SR-IOV fixes
- Fixes for manual driver reload
- Add unique identifier for vega asics
- Clean up user fence handling with UVD/VCE/VCN blocks
- Convert DC to use core bpc attribute rather than a custom one
- Add GWS support for KFD
- Vega powerplay improvements
- Add CRC support for DCE 12
- SR-IOV support for new security policy
- Various cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529220944.14464-1-alexander.deucher@amd.com
The pointer dev is set to null yet it is being dereferenced when
checking dev->dqm->sched_policy. Fix this by performing the check
on dev->dqm->sched_policy after dev has been assigned and null
checked. Also remove the redundant null assignment to dev.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 1a058c3376 ("drm/amdkfd: New IOCTL to allocate queue GWS")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For passthrough, after rebooted the VM, driver will do
a baco reset before doing other driver initialization during loading
driver. For doing the baco reset, it will first
check the baco reset capability. So first need to set the
cap from the vbios information or baco reset won't be
enabled.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not necessary on soc15 and breaks driver reload on server cards.
Acked-by: Amber Lin <Amber.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Flora Cui <Flora.Cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a field in map_queues packet to indicate whether
this is a gws control queue. Only one queue per process
can be gws control queue. Change num_gws field in
map_process packet to 7 bits
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a new kfd ioctl to allocate queue GWS. Queue
GWS is released on queue destroy.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add functions in process queue manager to
set/unset queue gws. Also set process's number
of gws used. Currently only one queue in
process can use and use all gws.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GWS bo is shared between all kfd processes. Add function to add gws
to kfd process's bo list so gws can be evicted from and restored
for process.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On device initialization, KFD allocates all (64) gws which
is shared by all KFD processes.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add amdgpu_amdkfd interface to alloc and free gws
from amdgpu
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add amdgpu_amdkfd interface to get num_gws and add num_gws
to /sys/class/kfd/kfd/topology/nodes/x/properties. Only report
num_gws if MEC FW support GWS barriers. Currently it is
determined by a module parameter which will be replaced
with MEC FW version check when firmware is ready.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
TTM doesn't support CPU mapping of sg type bo (under which
mmio bo is created). Switch mmaping of mmio page to kfd
device file.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_destroy should be called amdgpu_cgs_destroy_device,
as it will use cgs context to read or write registers.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop use of the deprecated drmP.h header file.
While touching the list of include files:
- Divide include files in blocks of linux/* video/* drm/* etc.
Be consistent in the order of the blocks
- Sort individual blocks of include files
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526180532.1641-3-sam@ravnborg.org
The num_supplies variable is not used, delete it.
Build tested.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526180532.1641-2-sam@ravnborg.org
Restore calls to clk_{enable/disable} deleted after applying the wrong
version of the patch
Fixes: fd6905fca4 ("drm/stm: ltdc: remove clk_round_rate comment")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527115830.15836-1-benjamin.gaignard@st.com
The 'clips' member is a pointer, so assign NULL instead of 0.
This fixes the following sparse warning:
drivers/gpu/drm/drm_damage_helper.c:289:31: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527183714.11168-1-festevam@gmail.com
- Engine discovery query (Tvrtko)
- Support for DP YCbCr4:2:0 outputs (Gwan-gyeong)
- HDCP revocation support, refactoring (Ramalingam)
- Remove DRM_AUTH from IOCTLs which also have DRM_RENDER_ALLOW (Christian König)
- Asynchronous display power disabling (Imre)
- Perma-pin uC firmware and re-enable global reset (Fernando)
- GTT remapping for display, for bigger fb size and stride (Ville)
- Enable pipe HDR mode on ICL if only HDR planes are used (Ville)
- Kconfig to tweak the busyspin durations for i915_wait_request (Chris)
- Allow multiple user handles to the same VM (Chris)
- GT/GEM runtime pm improvements using wakerefs (Chris)
- Gen 4&5 render context support (Chris)
- Allow userspace to clone contexts on creation (Chris)
- SINGLE_TIMELINE flags for context creation (Chris)
- Allow specification of parallel execbuf (Chris)
Refactoring:
- Header refactoring (Jani)
- Move GraphicsTechnology files under gt/ (Chris)
- Sideband code refactoring (Chris)
Fixes:
- ICL DSI state readout and checker fixes (Vandita)
- GLK DSI picture corruption fix (Stanislav)
- HDMI deep color fixes (Clinton, Aditya)
- Fix driver unbinding from a device in use (Janusz)
- Fix clock gating with pipe scaling (Radhakrishna)
- Disable broken FBC on GLK (Daniel Drake)
- Miscellaneous GuC fixes (Michal)
- Fix MG PHY DP register programming (Imre)
- Add missing combo PHY lane power setup (Imre)
- Workarounds for early ICL VBT issues (Imre)
- Fix fastset vs. pfit on/off on HSW EDP transcoder (Ville)
- Add readout and state check for pch_pfit.force_thru (Ville)
- Miscellaneous display fixes and refactoring (Ville)
- Display workaround fixes (Ville)
- Enable audio even if ELD is bogus (Ville)
- Fix use-after-free in reporting create.size (Chris)
- Sideband fixes to avoid BYT hard lockups (Chris)
- Workaround fixes and improvements (Chris)
Maintainer shortcomings:
- Failure to adequately describe and give credit for all changes (Jani)
-----BEGIN PGP SIGNATURE-----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=U/nc
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Features:
- Engine discovery query (Tvrtko)
- Support for DP YCbCr4:2:0 outputs (Gwan-gyeong)
- HDCP revocation support, refactoring (Ramalingam)
- Remove DRM_AUTH from IOCTLs which also have DRM_RENDER_ALLOW (Christian König)
- Asynchronous display power disabling (Imre)
- Perma-pin uC firmware and re-enable global reset (Fernando)
- GTT remapping for display, for bigger fb size and stride (Ville)
- Enable pipe HDR mode on ICL if only HDR planes are used (Ville)
- Kconfig to tweak the busyspin durations for i915_wait_request (Chris)
- Allow multiple user handles to the same VM (Chris)
- GT/GEM runtime pm improvements using wakerefs (Chris)
- Gen 4&5 render context support (Chris)
- Allow userspace to clone contexts on creation (Chris)
- SINGLE_TIMELINE flags for context creation (Chris)
- Allow specification of parallel execbuf (Chris)
Refactoring:
- Header refactoring (Jani)
- Move GraphicsTechnology files under gt/ (Chris)
- Sideband code refactoring (Chris)
Fixes:
- ICL DSI state readout and checker fixes (Vandita)
- GLK DSI picture corruption fix (Stanislav)
- HDMI deep color fixes (Clinton, Aditya)
- Fix driver unbinding from a device in use (Janusz)
- Fix clock gating with pipe scaling (Radhakrishna)
- Disable broken FBC on GLK (Daniel Drake)
- Miscellaneous GuC fixes (Michal)
- Fix MG PHY DP register programming (Imre)
- Add missing combo PHY lane power setup (Imre)
- Workarounds for early ICL VBT issues (Imre)
- Fix fastset vs. pfit on/off on HSW EDP transcoder (Ville)
- Add readout and state check for pch_pfit.force_thru (Ville)
- Miscellaneous display fixes and refactoring (Ville)
- Display workaround fixes (Ville)
- Enable audio even if ELD is bogus (Ville)
- Fix use-after-free in reporting create.size (Chris)
- Sideband fixes to avoid BYT hard lockups (Chris)
- Workaround fixes and improvements (Chris)
Maintainer shortcomings:
- Failure to adequately describe and give credit for all changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87sgt3n45z.fsf@intel.com
Cross-subsystem Changes:
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
-----BEGIN PGP SIGNATURE-----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=2K7c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3, try #2:
UAPI Changes:
- Add HDR source metadata property.
- Make drm.h compile on GNU/kFreeBSD by including stdint.h
- Clarify how the userspace reviewer has to review new kernel UAPI.
- Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough.
Cross-subsystem Changes:
- video/hdmi: Add unpack function for DRM infoframes.
- Device tree bindings:
* Updating a property for Mali Midgard GPUs
* Updating a property for STM32 DSI panel
* Adding support for FriendlyELEC HD702E 800x1280 panel
* Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel
* Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT.
* Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel
with resistive touch found on TI's AM335X-EVM.
* Adding support for EDT ETM0430G0DH6 480x272 panel.
- Add OSD101T2587-53TS driver with DT bindings.
- Add Samsung S6E63M0 panel driver with DT bindings.
- Add VXT VL050-8048NT-C01 800x480 panel with DT bindings.
- Dma-buf:
- Make mmap callback actually optional.
- Documentation updates.
- Fix debugfs refcount inbalance.
- Remove unused sync_dump function.
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Add support for HDR infoframes and related EDID parsing.
- Remove prime sg_table caching, now done inside dma-buf.
- Add shiny new drm_gem_vram helpers for simple VRAM drivers;
with some fixes to the new API on top.
- Small fix to job cleanup without timeout handler.
- Documentation fixes to drm_fourcc.
- Replace lookups of drm_format with struct drm_format_info;
remove functions that become obsolete by this conversion.
- Remove double include in bridge/panel.c and some drivers.
- Remove drmP.h include from drm/edid and drm/dp.
- Fix null pointer deref in drm_fb_helper_hotplug_event().
- Remove most members from drm_fb_helper_crtc, only mode_set is kept.
- Remove race of fb helpers with userspace; only restore mode
when userspace is not master.
- Move legacy setup from drm_file.c to drm_legacy_misc.c
- Rework scheduler job destruction.
- drm/bus was removed, remove from TODO.
- Add __drm_atomic_helper_crtc_reset() to subclass crtc_state,
and convert some drivers to use it (conversion is not complete yet).
- Bump vblank timeout wait to 100 ms for atomic.
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually.
- v3d: Small cleanups, adding support for compute shaders,
reservation/synchronization fixes and job management refactoring,
fixes MMU and debugfs.
- lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs.
- stm/ltdc: Assorted fixes and adding FB modifier support.
- amdgpu: Avoid hw reset if guilty job was already signaled.
- virtio: Add seqno to fences, add trace events, use correct flags for fence allocation.
- Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API.
- sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers.
- bochs: Small fix to use PTR_RET_OR_ZERO and driver unload.
- gma500: header fixes
- cirrus: Remove unused files.
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
The use of the drmP.h header file is deprecated.
Remove use from all files in drm/*
so people do not look there and follow a bad example.
Build tested allyesconfig,allmodconfig on x86, arm etc.
Including alpha that is as always more challenging than
the rest.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526173535.32701-8-sam@ravnborg.org
Do not require users of drm_trace.h to include other
files just to let it build
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526173535.32701-7-sam@ravnborg.org
Do not require users of drm_legacy.h to include other
files just to let it build
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526173535.32701-6-sam@ravnborg.org
Do not require users of drm_internal.h to include other
files just to let it build
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526173535.32701-5-sam@ravnborg.org
Do not require users of drm_crtc_internal.h to include other
files just to let it build
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Link: https://patchwork.freedesktop.org/patch/msgid/20190526173535.32701-4-sam@ravnborg.org
Drop use of the deprecated drmP.h header file.
While touching the list of include files:
- Divide include files in blocks of linux/* drm/* etc.
- Sort individual blocks of include files
- Remove duplicated header file
v2:
- Be consistent in the order of the include blocks (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190519183636.19588-1-sam@ravnborg.org
Vertical front and back porch values on existing driver are swapped.
The existing timings are still working as expected, but to make sure
it can compatible with techstar ts8550b bsp timings this patch swap
the same values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190512184827.13905-1-jagan@amarulasolutions.com
This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.
Cc: stable@vger.kernel.org # v4.19
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.com
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later". Only the "obvious" versions of these matches are
included here, a number of "non-obvious" variants of text have been
found but those have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOgmlw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4rACfRqxGOGVLR/t6E9dDzOZRAdEz/mYAoJLZmziY
0YlSSSPtP5HI6JDh65Ng
=HXQb
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
In drm_load_edid_firmware(), fwstr is allocated by kstrdup(). And fwstr
is dereferenced in the following codes. However, memory allocation
functions such as kstrdup() may fail and returns NULL. Dereferencing
this null pointer may cause the kernel go wrong. Thus we should check
this kstrdup() operation.
Further, if kstrdup() returns NULL, we should return ERR_PTR(-ENOMEM) to
the caller site.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524023222.GA5302@zhanggen-UX430UQ
Acked-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are monitors which can have more than one preferred mode
set. There are chances in these monitors that if common modes are
added in function amdgpu_dm_connector_add_common_modes(), these
common modes can be calculated with different preferred mode than
the one used in function decide_crtc_timing_for_drm_display_mode().
The preferred mode can be different because after common modes
are added, the mode list is sorted and this changes the order of
preferred modes in the list. The first mode in the list with
preferred flag set is selected as preferred mode. Due to this the
preferred mode selected varies.
If same preferred mode is not selected in common mode calculation
and crtc timing, then during mode set instead of setting preferred
timing, common mode timing will be applied which can cause "out of
range" message in the monitor with monitor blanking out.
[How]
Sort the modes before adding common modes. The same sorting function
is called during common mode addition and deciding crtc timing.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current state on the connector is queried when getting the max bpc
rather than the new state. This means that a new max bpc value can only
currently take effect on the commit *after* it changes.
The new state should be passed in instead.
[How]
Pass down the dm_state as drm state to where we do color depth lookup.
The passed in state can still be NULL when called from
amdgpu_dm_connector_mode_valid, so make sure that we have reasonable
defaults in place. That should probably be addressed at some point.
This change now (correctly) causes a modeset to occur when changing the
max bpc for a connector.
v2: Drop extra TODO.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The custom "max bpc" property was added to limit color depth while the
DRM one was still being merged. It's been a few kernel versions since
then and this TODO was still sticking around.
[How]
Attach the DRM max bpc property to the connector and drop all of our
custom property management. Set the max bpc to 8 by default since
DRM defaults to the max in the range which would be 16 in this case.
No behavioral changes are intended with this patch, it should just be
a refactor.
v2: Don't force 8bpc when no state is given
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix code error to support value < 0 or > 1.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Hawking Zhang <hawking.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a file that provides a Unique ID for the GPU.
This will persist across machines and is guaranteed to be unique.
This is only available for GFX9 and newer, so older ASICs will not
have this file in the sysfs pool
v2: Store it in adev for ASICs that don't have a hwmgr
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A multi-socket server can have multiple PCIe segments so BFD is not enough
to distingush each GPU. Also add domain number into account when generating
gpu_id.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the VegaM information to KFD
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix a circular lock dependency exposed under userptr memory pressure.
The DQM lock is the only one taken inside the MMU notifier. We need
to make sure that no reclaim is done under this lock, and that
no other locks are taken under which reclaim is possible.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alloc format was never really supported by MEC FW. FW always
does one per pipe allocation.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose available numbers of both SDMA queue types in the topology.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Existing QUEUE_TYPE_SDMA means PCIe optimized SDMA queues.
Introduce a new QUEUE_TYPE_SDMA_XGMI, which is optimized
for non-PCIe transfer such as XGMI.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous codes assumes there are two sdma engines.
This is not true e.g., Raven only has 1 SDMA engine.
Fix the issue by using sdma engine number info in
device_info.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This avoids duplicated code.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of allocat hiq and sdma mqd from sub-allocator, allocate
them from a mqd trunk pool. This is done for all asics
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is preparation work to introduce more mqd allocation
scheme
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Free mqd_mem_obj it GTT buffer allocation for MQD+control stack fails.
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MEC FW for some new asic requires all SDMA MQDs to be in a continuous
trunk of memory right after HIQ MQD. Add a field in device queue manager
to hold the HIQ/SDMA MQD memory object and allocate MQD trunk on device
queue manager initialization.
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also initialize mqd size on mqd manager initialization
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously mqd managers was initialized on demand. As there
are only a few type of mqd managers, the on demand initialization
doesn't save too much memory. Initialize them on device
queue initialization instead and delete the get_mqd_manager
interface. This makes codes more organized for future changes.
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With introduction of new mqd allocation scheme for HIQ,
DIQ and HIQ use different mqd allocation scheme, DIQ
can't reuse HIQ mqd manager
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Global function mqd_manager_init just calls asic-specific functions and it
is not necessary. Delete it and introduce a mqd_manager_init interface in
dqm for asic-specific mqd manager init. Call mqd_manager_init interface
directly to initialize mqd manager
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long for number of pages.
Check that pfns are valid after hmm_vma_fault. If they are not,
return an error instead of continuing with invalid page pointers and
PTEs.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If using old kernel config file, CONFIG_ZONE_DEVICE is not selected,
so CONFIG_HMM and CONFIG_HMM_MIRROR is not enabled, the current driver
error message "Failed to register MMU notifier" is not clear. Inform
user with more descriptive message on how to fix the missing kernel
config option.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109808
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
userptr may cross two VMAs if the forked child process (not call exec
after fork) malloc buffer, then free it, and then malloc larger size
buf, kerenl will create new VMA adjacent to old VMA which was cloned
from parent process, some pages of userptr are in the first VMA, the
rest pages are in the second VMA.
HMM expects range only have one VMA, loop over all VMAs in the address
range, create multiple ranges to handle this case. See
is_mergeable_anon_vma in mm/mmap.c for details.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Userptr restore may have concurrent userptr invalidation after
hmm_vma_fault adds the range to the hmm->ranges list, needs call
hmm_vma_range_done to remove the range from hmm->ranges list first,
then reschedule the restore worker. Otherwise hmm_vma_fault will add
same range to the list, this will cause loop in the list because
range->next point to range itself.
Add function untrack_invalid_user_pages to reduce code duplication.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only select HMM_MIRROR will get kernel config dependency warnings
if CONFIG_HMM is missing in the config. Add depends on HMM will
solve the issue.
Add conditional compilation to fix compilation errors if HMM_MIRROR
is not enabled as HMM config is not enabled.
Remove unused function amdgpu_ttm_tt_mark_user_pages.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use HMM helper function hmm_vma_fault() to get physical pages backing
userptr and start CPU page table update track of those pages. Then use
hmm_vma_range_done() to check if those pages are updated before
amdgpu_cs_submit for gfx or before user queues are resumed for kfd.
If userptr pages are updated, for gfx, amdgpu_cs_ioctl will restart
from scratch, for kfd, restore worker is rescheduled to retry.
HMM simplify the CPU page table concurrent update check, so remove
guptasklock, mmu_invalidations, last_set_pages fields from
amdgpu_ttm_tt struct.
HMM does not pin the page (increase page ref count), so remove related
operations like release_pages(), put_page(), mark_page_dirty().
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is circular lock between gfx and kfd path with HMM change:
lock(dqm) -> bo::reserve -> amdgpu_mn_lock
To avoid this, move init/unint_mqd() out of lock(dqm), to remove nested
locking between mmap_sem and bo::reserve. The locking order
is: bo::reserve -> amdgpu_mn_lock(p->mn)
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace our MMU notifier with hmm_mirror_ops.sync_cpu_device_pagetables
callback. Enable CONFIG_HMM and CONFIG_HMM_MIRROR as a dependency in
DRM_AMDGPU_USERPTR Kconfig.
It supports both KFD userptr and gfx userptr paths.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a bug found in vml2 xgmi logic:
mtype is always sent as NC on the VMC to TC interface for a page walk,
regardless of whether the request is being sent to local or remote GPU.
NC means non-coherent and will cause the VMC return data to be cached
in the TCC (versus UC – uncached will not cache the data). Since the
page table updates are being done by SDMA/HDP, then TCC will never be
updated and the GC VML2 will continue to hit on the TCC and never get
the updated page tables and result in a fault.
Heave weigh tlb invalidation does a WB/INVAL of the L1/L2 GL data
caches so TCC will not be hit on next request
Signed-off-by: shaoyunl <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ttmp[4:5] is initialized by the SPI with SPI_GDBG_TRAP_DATA* values.
These values are more useful to the debugger than ttmp[14:15], which
carries dispatch_scratch_base*. There are too few registers to
preserve both.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SQ_WAVE_IB_STS.RCNT grew from 4 bits to 5 in gfx9. Do not truncate
when saving in the high bits of TTMP1.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If instruction fetch fails the wave cannot be halted and returned to
the shader without raising MEM_VIOL again. Currently the wave is
terminated if this occurs, but this loses information about the cause
of the fault. The debugger would prefer the faulting wave state to be
context-saved.
Poll inside the trap handler until TRAPSTS.SAVECTX indicates context
save is ready. Exit the poll loop and complete the remainder of the
exception handler, then return to the shader. The next instruction
fetch will be from the trap handler and not the faulting PC. Context
save will then deschedule the wave and save its state.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When MEM_VIOL is asserted the context save handler rewinds the
program counter. This is incorrect for any source of the exception.
MEM_VIOL may be raised in normal operation by out-of-bounds access
to LDS or GDS and does not require special handling.
Remove PC adjustment when MEM_VIOL has been raised.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix compute profile switching on process termination.
Add a dedicated reference counter to keep track of entry/exit to/from
compute profile. This enables switching compute profiles for other
reasons than process creation or termination.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FW of some new ASICs requires sdma mqd size to be not more than
128 dwords. Repurpose the last 2 reserved fields of sdma mqd for
driver internal use, so the total mqd size is no bigger than 128
dwords
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sdma_queue_id is sdma queue index inside one sdma engine.
sdma_id is sdma queue index among all sdma engines. Use
those two names properly.
Signed-off-by: Oak Zeng <ozeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add debug messages during SDMA queue allocation.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maximumly support 64 sdma queues
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support DPM/DS/ULV related bitmasks of ppfeaturemask module parameter.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It does the same thing we were doing already. I though it needed
work for gen3/4 speeds, but that seems to be covered already.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The UVD/VCE bits are set wrongly. This causes the UVD/VCE clocks
are not brought back correctly on needed.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v1: replace casting to unsigned long with div64_ul
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Slava Abramov <slava.abramov@amd.com>
Tested-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add pm_enabled to control the dpm off/on.
v2: Directly return 0 to replace return ret and merge some check code.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Hawking Zhang <hawking.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes the warning below
error: ‘feature_mask’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
*features_enabled = ((((uint64_t)feature_mask[0] << SMU_FEATURES_LOW_SHIFT) & SMU_FEATURES_LOW_MASK) |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^
(((uint64_t)feature_mask[1] << SMU_FEATURES_HIGH_SHIFT) & SMU_FEATURES_HIGH_MASK));
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DRM_ERROR error message. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If RAS or XGMI are enabled, you have to use mode1 reset rather
than BACO.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disable driver, OS will set backlight optimization
then do stop device. But this flag will cause driver to
enable ABM when driver disabled.
[How]
Send ABM disable command before destroy ABM construct
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
move the update of otg instance outside of hw programming logic,
since this is sw state, it should always be updated and should
never be optimized away.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.
[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.
Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPRX should send the VCP extended colorimetry packet if the
sink supports DPCD rev1.4 and reports the extended colorimetry
bit.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. No real HPD plug in/out but HPD happens,
the driver notifies OS connection changed.
2. No display in target.
When HPD goes low to high,
the driver should regard as HPD and enter setmode flow.
[How]
In this case, even stream didn't change but still retrain.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Reuse existent code path and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DPMS state of a display should not impact whether we want to enable fast boot.
Currently fast boot is not enabled when resuming from S4 because of this.
[How]
Remove check for DPMS state when determining if fast boot
can be applied.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many IGT tests require CRC capture in order to confirm that the output
is visually correct.
These skip on dce120 because configure_crc and get_crc aren't set.
[How]
Hook up is_tg_enabled, configure_crc and get_crc functions on dce120's
timing generator.
The logic should be the same as DCE and DCN with some minor register
naming differences.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add these parameters for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
