Enable SMP support for mt7623.
Enable SMP support for mt2701
Add pinctrl for mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JHE5
-----END PGP SIGNATURE-----
Merge tag 'v4.5-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: dts updates for v4.6" from Matthias Brugger:
Add support for mt7623 SoC.
Enable SMP support for mt7623.
Enable SMP support for mt2701
Add pinctrl for mt2701
* tag 'v4.5-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: Add pinctrl/GPIO/EINT node for mt2701
ARM: dts: mt2701: enable basic SMP bringup for mt2701
ARM: dts: mt7623: enable SMP bringup
ARM: dts: mediatek: add MT7623 basic support
Document: DT: Add bindings for mediatek MT7623 SoC Platform
OrangePi Plus board has dwo leds - green ("pwr") and red ("status")
and a switch ("sw4"). This patch describes them in a devicetree.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds correct aliases to spi and i2c buses so that they get
correct matching bus numbers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds i2c6 device node and pinctrls required for IFC6410 on
MIPI-CSI connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables i2c bus for camera via mipi-csi connector on ifc6410.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds gsbi4 and i2c node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing i2c2 pinctrl information in i2c2 node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables spi device on the 30 pin expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds spi5 device node, spi5 is used on ifc6410 on the
expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing i2c pinctrl sleep states.
Also add 16mA drive strength to the pins so that we can detect wide
range of i2c devices on the other side of level shifters.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds PCIE support to APQ8064, tested with Ethernet on
Compulab QS600 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
As there are more pinctrls to come, moving these to dedicated dtsi makes
more sense.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes i2c lables to be inline with serial labels.
The reason to do this is that it would look odd if we add aliases in the
board file along with serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
LogicPD has two main Torpedo styles, a version with wireless and a version
without wireless. This version has Bluetooth and WiFi, but there really
isn't an easy way to identify them automatically. This simply adds
"Wireless" to the model to distinguish it from the 'base' model that will
come soon.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] dm816x TRM: SPRUGX8C: 9.2.4.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM335x TRM: SPRUH73L: 7.1.3.3.12.2 NAND Device-Ready Pin
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM437x TRM: SPRUHL7D: 9.1.3.3.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wait pin monitoring is not used for nand so it is pointless to
have the gpmc,wait-monitoring-ns property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The H3 ir receiver is completely compatible with the one found in the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the corresponding device node for R_PIO on H3 to the dtsi. Support
for the controller was added in earlier commit.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
APB0 is bearly mentioned in H3 User Manual and it is only setup in the
Allwinners kernel dump for CIR. I have verified experimentally that the
gate for R_PIO exists and works, though. There are probably other gates
there but I don't know their order right now and I don't have access to
their peripherals on my board to test them.
After some experiments and reviewing how this is organized on other
sunxi SoCs, I couldn't actually find any way to disable clocks for R_PIO
and they are working properly without doing anything so I assume they
are connected straight to the 24Mhz oscillator for now.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add barebones K2G evm dts. This DTS allows the board to boot using a
ram based filesystem.
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
K2G is the newest addition of TI's Keystone 2 product family. It is a
single core Cortex A15 and a C66x DSP.
K2G supports standard peripherals such as SPI, UART, MMC and USB 2.0.
Includes two dual-core Programmable Real-time Unit and Industrial
Communication Subsystems (PRU-ICSS).
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
This device is targeted for a variety of applications which include, but
are not limited to:
Home audio
Professional audio
Industrial Programmable Logic Control
The peripheral nodes that have been included in this patch have been
tested during bring-up. Since all peripherals will not necessarily be
used on all boards, disable all peripherals by default. This allow
the board dts to selectively choose which peripherals it wants to
enable.
This SoC now uses the next generation of power management architecture
with the PM functionality located in a microcontroller embedded in the SOC.
Support for this new PM architecture along with other peripherals will be
added in future patches.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Use early console instead of earlyprintk which is supposed to use for
very early debugging (DEBUG_LL).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds USB HS support in host mode only.
This port supports OTG mode, but the device more is not working
properly as of now.
Once the device mode fixed, the node will be updated to support OTG.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Make it possible to select which I2C IP core you want to run on the
EXIO-A connector. This is the reference how to use this feature. Update
the copyright while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Addition of the ADC for sama5d2 and sama5d2_xplained
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mzUX
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.6-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT changes for 4.6:
- Addition of the ADC for sama5d2 and sama5d2_xplained
* tag 'at91-ab-4.6-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2 Xplained: enable the adc device
ARM: dts: at91: sama5d2: add adc device
Signed-off-by: Olof Johansson <olof@lixom.net>
All Exynos SoCs have the same syscon reboot and poweroff device nodes so
there is no need to duplicate the same on each SoC dtsi and can be moved
to a common dtsi that can be included by all the SoCs dtsi files.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung,com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
- Finalize RealView the PB1176 and PB11MPCore device trees
- Move Versatile to use the power/reset driver instead of a
custom restart hook
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWwZOHAAoJEEEQszewGV1zsg8P/3xtEDPR9GJAuzzgV8o8hmpA
psFc4PmdQcp1e19gb2oi0oKcv9xDzsKGavy/BYMMn9HQ6v4wTmtM9qMwNgRyTWZq
RyAtnPxUP543Qiae1tdPBp700cyg8UsEcL56qhwemCOucjwD6wZNiAAs6bUh9mYa
J1liSaarw+XOhzUdfqffk0JUac1oqnvdiiOLwAXsdWbCfNdkJGbfZ0N5TuUANMhM
RXeqq8giEZAbvQtqumZv6c7Qk02zeG6tYq6R7lsW65IIvOhVk2rxYdC8ZhPTojxR
V7jMLnA4xYn5IaLE4l7Z32AqKWGnsThmdP4OEMLnRhEduutHWUVj3XHlPAlS1pN1
cD+mHuP48+5AscEL6Xf6+jeVYFkdER3RX9DgGZxUgLENw9T4g0/vq2DSGijwPuDN
NB++vroPQoFEoPzCOx+JvO88VctabzuV7Z6rIvSLcIwPAhHvzMk1G+gy6hrUz5Bc
cfovCqw1C8Y15srcIRhNr8dxDyZ3bpsatbSQNgPly4cHnAHLB8olTpXdfBzKIbKO
FQmiAh+aPljOXxJT5yTg+3isIWA2tkc67WNiuX3+aKp38Ux2TNvDYCGf+LXF0RsU
hgLGe3f4Bqw9xIMPYqQZM2UBl91p48ErhhmNJCWjceVgLEDHsCxaIvCx+oqLyYdv
00TEPFLVtam4SJbqgJwq
=NvEo
-----END PGP SIGNATURE-----
Merge tag 'versatile-dt-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Versatile DT cleanups from Linus Walleij:
"this is a first pull request for my cleanups for the Versatile, as
the finished stuff should not be sitting in my tree but in ARM SoC.
This completes the ARM RealView PB1176 and PB11MPCore device trees,
and moves the Versatile to use power/reset.
The idea is to keep working on this cleanup branch and send additional
patches on top of this one as the prerequisites are merged into the MTD
and FBDEV subsystems. So please create a special versatile cleanup branch
(or suggest another approach).
As it happens, board files and device trees need to change at the same
time to make logical sense, especially for Versatile where auxdata is
replaced with DT entries, such as when reset is moved in the last patch
in this set. The MTD and CLCD changes will share this characteristic."
Versatile family cleanups step 1:
- Finalize RealView the PB1176 and PB11MPCore device trees
- Move Versatile to use the power/reset driver instead of a
custom restart hook
* tag 'versatile-dt-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: versatile: move restart to the device tree
ARM: realview: add the DS1338 RTC to PB1176 DT
ARM: pb1176: add ethernet to devicetree
ARM: pb1176: add ISP1761 USB OTG host controller
ARM: pb1176: add AACI to the device tree
ARM: pb1176: add ICST307 clocks to the device tree
ARM: realview: fix up PB11MP flash compat strings
ARM: realview: add flash devices to the PB1176 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add SROM controller device nodes.
2. Add Ethernet chip as child of SROM controller on SMDK5410.
3. Allow simultaneous usage exynos-rng and s5p-sss drivers on Exynos5.
4. Cleanup CPU configuration on Exynos542x/5800.
5. Add necessary nodes for cpufreq-dt driver on Exynos542x/5800 (OPPs,
regulator supplies) which allows frequency and voltage scalling
of this SoC.
6. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWwRf5AAoJEME3ZuaGi4PXrAIP/RGMMvPNhSRp5EMbrZlK3gsg
Q32cZgxXGW5AIgxhhXkBCDrfUFD3bpw7hAM4eWOScJvZWp0MagQJC7/9AKZ4/fRh
J5gDmGyRrhhotUR2lzrJrN5YBffOlWiJ9VnVapWfdkYUDXXsL76xHdXnPyOnVlOv
VcUh1g7Tbv1ao0U3tuY2PSpryk4Vi9R/SBSSQu9Tn6UChAFyZTpbPgbeS24tKkas
jJDbfJS6eIBnyoImGiKC1E9eaERL2lh9YjZ323tzNSav4BYRLLlRe3olZf7uKQRs
GIlyJbtcYu72+IANXkjjF+pKen3x8b1BWrUbyWD4nxRkn0gR6czRAzqw+sX0bBRl
hYPd/IxnilgJni06e76YL0qwdSjvOThgiMNhojrU4y21Tr3xqzC6TJQiLK4dWlTD
RiAReOCQTfxV3dlQpLixIN1icRlwkJz2JO791iavIEilZIT0dRrNkzQNILWj0GMU
x9/JS/axja/ckKImMRVMd3ZCtDkYD4B0QzFEElcTe9oIhEmfk3VYZIxXu4a9U+5q
NWU/hPxHoOk16tq6G8TvwwTCH561HTWnkXn1kpku8gr5x8rO9tH5KfgWX8syZAoh
a/ugdzntt0GOZpSRhOYE9zXjKBlxiidq53fdVDFTw95V6r6JJYNWfmkWXbT2jteR
L/UrZA45YPJCydvtRztE
=OC9Z
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree updates and improvements for v4.6:
1. Add SROM controller device nodes.
2. Add Ethernet chip as child of SROM controller on SMDK5410.
3. Allow simultaneous usage exynos-rng and s5p-sss drivers on Exynos5.
4. Cleanup CPU configuration on Exynos542x/5800.
5. Add necessary nodes for cpufreq-dt driver on Exynos542x/5800 (OPPs,
regulator supplies) which allows frequency and voltage scalling
of this SoC.
6. Minor cleanups.
* tag 'samsung-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: Replace legacy *,wakeup property with wakeup-source for exynos boards
ARM: dts: Add GSCL block parent clock management to pm domain on exynos542x
ARM: dts: Extend existing CPU OPP for exynos5800
ARM: dts: Add CPU OPP properties for exynos542x/5800
ARM: dts: Add cluster regulator supply properties for exynos542x/5800
ARM: dts: Make CPU configuration more readable on exynos542x/5800
ARM: dts: Replace legacy *,wakeup property with wakeup-source on s5pv210
ARM: dts: Allow simultaneous usage exynos-rng and s5p-sss drivers on exynos5
ARM: dts: Add Ethernet chip to exynos5410-smdk5410
ARM: dts: Add SROM to exynos5410
ARM: dts: Add SROM device node for exynos5
ARM: dts: Add SROM device node for exynos4
ARM: dts: Add pinctrl support to exynos5410
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use SCIF and USBHS fallback compatibility strings
* Add Baud Rate Generator (BRG) support for (H)SCIF
* Enable SCIF_CLK frequency and pins
* Use GIC_* defines
* Enable audio on r8a7793/gose
* Enable HDMI vidio out on r8a7793
* Enable i2c on r8a7793/gose
* Enable QSPI on alt
* Enable GPIO keys and leds on gise
* Enable audio on porter
* Enable DU on porter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YmRO
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.6
* Use SCIF and USBHS fallback compatibility strings
* Add Baud Rate Generator (BRG) support for (H)SCIF
* Enable SCIF_CLK frequency and pins
* Use GIC_* defines
* Enable audio on r8a7793/gose
* Enable HDMI vidio out on r8a7793
* Enable i2c on r8a7793/gose
* Enable QSPI on alt
* Enable GPIO keys and leds on gise
* Enable audio on porter
* Enable DU on porter
* tag 'renesas-dt-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (68 commits)
ARM: dts: silk: Enable SCIF_CLK frequency and pins
ARM: dts: porter: Enable SCIF_CLK frequency and pins
ARM: dts: marzen: Enable SCIF_CLK frequency and pins
ARM: dts: lager: Enable SCIF_CLK frequency and pins
ARM: dts: koelsch: Enable SCIF_CLK frequency and pins
ARM: dts: gose: Enable SCIF_CLK frequency and pins
ARM: dts: bockw: Enable SCIF_CLK frequency and pins
ARM: dts: alt: Enable SCIF_CLK frequency and pins
ARM: dts: r8a7794: Add BRG support for (H)SCIF
ARM: dts: r8a7793: Add BRG support for SCIF
ARM: dts: r8a7791: Add BRG support for (H)SCIF
ARM: dts: r8a7790: Add BRG support for (H)SCIF
ARM: dts: r8a7779: Add BRG support for SCIF
ARM: dts: r8a7778: Add BRG support for SCIF
ARM: dts: r8a7794: Rename the serial port clock to fck
ARM: dts: r8a7793: Rename the serial port clock to fck
ARM: dts: r8a7791: Rename the serial port clock to fck
ARM: dts: r8a7790: Rename the serial port clock to fck
ARM: dts: r8a7779: Rename the serial port clock to fck
ARM: dts: r8a7778: Rename the serial port clock to fck
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Initial device tree for the Artpec-6 SoC.
Signed-off-by: Lars Persson <larper@axis.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
nodes and fixes like the increased drive-strength on the firefly.
Most interesting is maybe the enablement of the pl330 option
for handling the broken flushp operation that is present on the
current Rockchip SoCs. Together with the driver-side enablement
this should give us working dma finally.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWvGKWAAoJEPOmecmc0R2B2j4IAKSBKgak7uASVfvycAnJ/E7a
jNjcz9s/SAWGAu+ES36rX23r1/u/UlkdDX0yS0vCFR4eHNn35uUrl3lQdqjFEDXZ
f/c9gCrHsfvQQJPLGRzkhFIrQ6L/Anrgk5nq75+C4GvMFRDsDo5qqRnS0iP3wIZP
VALc9PFqq9kJnnrdFymHVgc9ETCR+kTM9YGqDTzHYT2pHKxkBTAANx+Pr7/1Ib0b
BM/he5i7/K+NVb9pjw6t8JbyT2JgST+UcNFeGn6jYylYdW4awFzFvJN0Q9pp989y
7mjJe6Suh36tjp0kX0DnOvBCWYXB2i62cSsjFxsf8rZGjCbZ3YtXS15EWwXsxto=
=wj5r
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Assorted bunch of 32bit Rockchip devicetree changes. More clocks,
nodes and fixes like the increased drive-strength on the firefly.
Most interesting is maybe the enablement of the pl330 option
for handling the broken flushp operation that is present on the
current Rockchip SoCs. Together with the driver-side enablement
this should give us working dma finally.
* tag 'v4.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (30 commits)
ARM: dts: cros-ec-keyboard: Add LOCK key to keyboard matrix
ARM: dts: rockchip: replace gpio-key,wakeup with wakeup-source property
ARM: dts: rockchip: add arm,pl330-broken-no-flushp quirk for rk3036 SoCs
ARM: dts: rockchip: Add arm, pl330-broken-no-flushp quirk for rk3xxx platform
ARM: dts: rockchip: Add arm, pl330-broken-no-flushp quirk for rk3288 platform
dt-bindings: rockchip-dw-mshc: add RK3036 dw-mshc description
ARM: dts: rockchip: increase the mclk_fs to 512 for kylin board
ARM: dts: rockchip: support the spi for rk3036
ARM: dts: rockchip: add mclk for rt5616 on rk3036 kylin board
ARM: dts: rockchip: add the leds control for rk3036-kylin board
ARM: dts: rockchip: add tsadc node
clk: rockchip: Add new id for rk3066 tsadc clock
ARM: dts: rockchip: add clock-cells for usb phy nodes
ARM: dts: rockchip: Assign RK3288 EDP_24M input centrally
ARM: dts: rockchip: add soc-specific compatibles for rk3036 SoCs
ARM: dts: rockchip: Bump sd card pin drive strength up on firefly boards
dt-bindings: rockchip-dw-mshc: add RK3368 dw-mshc description
ARM: dts: rockchip: Add the SDIO wifi on Radxa Rock2 square
ARM: dts: rockchip: Add the iodomains for the Rock2 SOM
ARM: dts: rockchip: add rk3288 mipi_dsi nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge DT changes for lpc32xx from Vladimir Zapolskiy:
"The changes add description of clock providers and clock consumers,
define default irq types of SoC controllers and add PHY3250 board
regulators.
I'm adding an official LPC32xx maintainer Roland to Cc, however he seems
to be unresponsive for a quite long time (since 2014)."
* 'lpc32xx/dt' of https://github.com/vzapolskiy/linux:
arm: dts: phy3250: add SD fixed regulator
arm: dts: phy3250: add lcd and backlight fixed regulators
arm: dts: lpc32xx: assign interrupt types
arm: dts: lpc32xx: remove clock frequency property from UART device nodes
arm: dts: lpc32xx: add USB clock controller
arm: dts: lpc32xx: add clock properties to device nodes
arm: dts: lpc32xx: add clock controller device node
arm: dts: lpc32xx: add device nodes for external oscillators
dt-bindings: create arm/nxp folder and move LPC32xx SoC description to it
Signed-off-by: Olof Johansson <olof@lixom.net>
Keyboard driver for GPIO buttons(gpio-keys) checks for the legacy
"gpio-key,wakeup" boolean property to enable gpio buttons as wakeup
source.
Few dts files assign value "1" to gpio-key,wakeup which is incorrect.
Since the presence of the boolean property indicates it is enabled,
value of "0" or "1" have no significance.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property which inturn fixes the above mentioned issue.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tAiy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for omaps against v4.5-rc5:
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
* tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
Signed-off-by: Olof Johansson <olof@lixom.net>
PIN_PA15 macro has the same value as PIN_PA14 so we were overriding PA14
mux/configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 7f16cb676c ("ARM: at91/dt: add sama5d2 pinmux")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWwEEWAAoJEFBXWFqHsHzOvv4H/29Q3aZBN/L/0JzPyCckfWSw
/l2UGsFW5UIBPbrOPW9tEPd4WRAUQ3BJKM2iNvvSSeNMvEO/Ni1+CtzQabCv7CGb
sKRZOIQ8e8782K4aNmCMMwrVBhPMAewFuh4DkCDdN55sE5kN9CkDO0d6jzaHsDJf
8GnuT5kq6qblV1HdsdVnEBjwL73v3wByUhUN3T6BplM4l9GtRRu7ox6s3dDdM4jG
ohBRafPo0s+pMOI8LRs7howHQwAuSHCMP7zOzqCOwvSAa+GOwKIjpQFvAKU+mfex
h+c2bdNxSCkDPG/QBwfk723qRWrDND0hMetHGNFn1zh8s0HhBzp7bNXKnLC5JF8=
=9ONj
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for v4.5:
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
* tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57 discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rk2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps against v4.5-rc3:
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57 discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
* tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.5 (part 2)
- Fix the missing mtd flash on linkstation lswtgl
- Use unique machine name for the kirkwood ds112 (for Debian flash-kernel tool)
* tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds a dts file to support the Nexus7 2013
device. Its based off of the qcom-apq8064-ifc6410.dts
which is similar hardware.
Also includes some comments and context folded in
from Vinay Simha BN <simhavcs@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds address-cell and size-cell values to the i2c3 bus
in the qcom-apq8064.dtsi, which is needed to describe devices
on that bus.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These clocks are fixed rate board sources that should be in DT.
Add them.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the additional reserved regions found on 8974 based devices.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
All the clocks referenced by the GPIO banks were not the good ones.
Reported-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
This change does not break existing userspace or Maemo software because
isp1704_charger.c always export power supply device under isp1704 name.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add EEPROM at 0x50 that describes the board configuration.
This is useful for userspace programs that may need to check board
revision and other similar information.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Logic PD SOM-LV has a USB Host Controller connected to 3-port
hub. This enables the pin muxing for the host controller and
ehci-phy.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes DTS structure more readable.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Logic PD DM37xx SOM-LV devkit consists of a base board and a SOM.
While the SOM (System on Module) supports Bluetooth and WiFi, LPD did not
obtain an FCC ID, so anyone who uses it will have to go through certification.
I have only tested the Type 28 Display, SMSC9211 Ethernet, SD/MMC and basic
power management, however the overall current seems high.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The backlight pin is shared with Timer 10 PWM. This patch allows the
pwm_bl driver to enable the pwm run by this timer to dim the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add linux,can-disable; to all gpios exported from gpio-keys driver, so
userspace can disable them
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the OTG USB controller on the A7HD.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
4.5 because required header files went through other trees, plus the
AUX uart support this time around.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MTTP
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-02-17' into devicetree/next
This pull request covers mostly DT changes that didn't make it into
4.5 because required header files went through other trees, plus the
AUX uart support this time around.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SoCs on am43x-epos-evm are named am438x.
Hence add the compatibility string and remove the am4372 string.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 8e6ebfaa9b.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define the generic R8A7794 part of the EtherAVB device node.
Based on the commit 46ece349aa ("ARM: shmobile: r8a7791: add EtherAVB DT
support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock to the R8A7794 device tree.
Based on the commit eaa870b305 ("ARM: shmobile: r8a7791: add EtherAVB
clock").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Changelog text from a similar patch by Sudeep Holla.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Add a device node for the L2 cache, and link the CPU nodes to it.
The L2 cache for the Cortex-A7 CPU cores is 512 KiB large (organized as
64 KiB x 8 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the L2 cache, and link the CPU node to it.
The L2 cache for the Cortex-A15 CPU cores is 1 MiB large (organized as
64 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the L2 cache, and link the CPU nodes to it.
The L2 cache for the Cortex-A15 CPU cores is 1 MiB large (organized as
64 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the L2 caches, and link the CPU nodes to them.
The L2 cache for the Cortex-A15 CPU cores is 2 MiB large (organized as
128 KiB x 16 ways).
The L2 cache for the Cortex-A7 CPU cores is 512 KiB large (organized as
64 KiB x 8 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the L2 caches, and link the CPU node to its L2
cache node.
The L2 cache for the Cortex-A15 CPU cores is 1 MiB large (organized as
64 KiB x 16 ways), and located in PM domain A3SM.
The L2 cache for the Cortex-A7 CPU cores is 512 KiB large (organized as
64 KiB x 8 ways), and located in PM domain A3KM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables to use thermal-zone on r8a7793.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)
And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.
You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADC device, and remove the adc_op_clk which is useless since the
adc sampling frequency is configured with sysfs.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It's pretty similar to the STM32F429, but there are some
subtle changes required to boot successfully.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Enable the otg/drc usb controller on the MK802.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23/A33 Q8 tablets have an X-Powers AXP223 PMIC connected via RSB. Its
regulators provide power to various parts of the SoC and the board.
Also add lcd regulator supply for simplefb and update the existing
vmmc-supply for mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board has a X-Powers AXP223 PMIC connected via RSB. Its regulators
provide power to various parts of the SoC and the board.
Also update the regulator supply phandles.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch enables to use thermal-zone on r8a7791.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)
And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.
You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables to use thermal-zone on r8a7790.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)
And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.
You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When finishing the Porter sound support patch, I managed to call the JP3
jumper SW3 in the comment. Fix this along with (also miscalled) jumper
positions...
Fixes: 493b4da7c1 ("ARM: dts: porter: add sound support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the ARM SP805 Watchdog timer to the Northstar Plus
device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM SP804 timer to the Northstar Plus device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM Performance Monitor Unit to the Northstar Plus
device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is a double definition of the CPUs present in the device tree.
Remove unnecessary cpu device tree definition.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding the ranges value is preventing the PCI nodes from working.
Pulling them out outside makes them work again (and makes it similar to
the NS2 device tree).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
OMAP5 has 3 thermal zones cpu, core and multimedia.
On the other hand DRA7 has 5 thermal zones cpu, gpu, core, dspeve
and iva. Currently cpu, core and multimedia are being added via device tree
and the other 2 are getting added via kernel. Add the missing thermal
domains in device tree so we can create the zones with the appropriate
trip numbers, type and temperatures.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes a dtsi file to contain the thermal data
for IVA domain. This data will enable a thermal shutdown at 125C.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes a dtsi file to contain the thermal data
for DSPEVE domain. This data will enable a thermal shutdown at 125C.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DWC3's tx-fifo-resize property has been deprecated
because of it being unnecessary to any HW other than
OMAP5 ES1.0.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds an idle pinctrl state, which will be used
by the driver to avoid incoming data during clock
rate changes or data flushing.
Signed-off-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MCLK is provided by an external clock of 24.576MHz.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART0 device is the device to be used for boot console output.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide RESET GPIO for the USB PHY, the USB Host port mode and
the PHY device for the controller. Also provides pin multiplexer
information for USB host pins.
Signed-off-by: Pau Pajuel <ppajuel@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 device is the device to be used for boot console output.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch defines the pin muxing to configure the hsusb0 through
the twl4030 PMIC, because we can't always assume the bootloader will
do it correctly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds the modem to the SSI port.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds all necessary information
to initialize the SSI module, but does not yet add the
modem information.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devkit has an AT25 EEPROM on MCSPI1. Enable this with default
parameters.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulator and fix pin muxing to allow Panel to sleep and
wake from sleep for some low power improvements.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Wireless version of the SOM uses an AT24 EEPROM to store product ID.
The EEPROM is readonly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Logic PD Torpedo standard kits come with a SOM populated to us an
8-bit parallel camera interface. This patch pin muxes the omap3-isp
pins, sets the MT9P031 clicks, and configures the i2c2 bus to communicate
with the mt9p031 on address 0x48.
I have not done a lot of testing, but when modprobing
mt9p031, then omap3-isp, the board responds with
MT9P031 detected at address 0x48.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.
Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.
Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit adds the Device Tree description for the 1GB NAND flash
present in the Armada 370 DB and Armada XP DB evaluation boards from
Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This enables the GPIO-a support for Broadcom NSP SoC
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The PB1176 device tree was missing the SMSC9118 ethernet adapter,
so add it. Since this peripheral is not in either development
chip but on the board itself, it gets defined in the root node
of the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The USB host controller was missing from the device tree so add
it. This device is not inside either the development chip or the
FPGA but mounted on the board, so it ends up in the root node of
the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device tree was missing the definition of the AACI
Advanced Audio Codec Interface, so add it. Tested on the hardware
and it works.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The two flash memories in the PB11MPCore have their VPP/WP
lines controlled from the system controller add-on in the MTD
subsystem. "arm,versatile-flash" is the first compatible string
to use to get the right support.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the flash memories and ROM to the PB1175 DTS file.
The secure flash is marked as "disabled" by default so as to
protect the user from overwriting the boot monitor.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STM32F429 allows to remap FMC SDRAM Bank 1 from 0xc0000000 to 0x0,
by writing 0x4 to SYSCFG_MEMRMP register.
As mentionned in the reference manual (see chapter 9.3.1), the performance
gain is really interresting:
"In remap mode at address 0x0000 0000, the CPU can access the external
memory via ICode bus instead of System bus which boosts up the
performance."
These are the dhrystone results with and without the remap enabled:
Default (SDRAM in 0xc0000000):
---------------------------------
Microseconds for one run through Dhrystone: 31.8
Dhrystones per Second: 31416.9
Remap (SDRAM in 0x0000000):
-----------------------------
Microseconds for one run through Dhrystone: 20.6
Dhrystones per Second: 48520.1
This patch first change the SDRAM start address to 0x0 for STM32429i-EVAL
board, and also set the dma-range property as the other masters than the M4
CPU still see SDRAM in 0xc0000000.
Note that the Discovery board cannot benefit from this feature, since the
SDRAM is connected to Bank 2.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
This patch selects USART1 pin configuration on PA9/PA10 pins
for both Eval and Disco boards.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
The STM32F429 MCU has 11 GPIO banks, with 16 pins per bank.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Add support for booting secondary CPUs on MT7623.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds basic chip support for Mediatek MT7623.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The change adds fixed voltage regulator for SD controller, ARM MMCI
controller driver uses it to control card power management.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Phytec PHY3250 board has GPIO controlled regulators for LCD and
backlight, add their descriptions to board DTS file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
LPC32xx interrupt controller has two cells, instead of zero
specify proper irq types for all consumers.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
If clock-frequency property is given, then it substitutes calculation
of supplying clock frequency from parent clock, this may break UART,
if parent clock is given and managed by common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds device node of LPC32xx USB clock controller and adds
clock properties to USB OHCI, USB device and I2C controller to USB phy
device nodes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds clock properties to all described peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Some existing drivers expect to get clock names, in those cases
clock-names are added as well.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx SoC has a clocking and power control unit (CPC) as a part
of system control block (SCB). CPC is supplied by two external
oscillators and it manages core and most of peripheral clocks, the
change adds SCB and CPC descriptions to shared LPC32xx dtsi file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx SoC has two external oscillators - one is mandatory and
always on 32768 Hz oscillator and one optional 10-20MHz oscillator,
which is practically always present on LPC32xx boards, because its
presence is needed to supply USB controller clock and by default it
supplies ARM and most of the peripheral clocks, LPC32xx User's Manual
references it as a main oscillator.
The change adds device nodes for both oscillators, frequency of
the main oscillator is selected to be 13MHz by default, this variant
is found on all LPC32xx reference boards.
The device nodes for external oscillators are needed to describe input
clocks of LPC32xx clock controller.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The tlv320aic3104 codec's master clock is coming from the SoC's CLKOUT2.
Select the SYS_CLK2 (via divider) as parent clock for CLKOUT2 and select
the same clock (SYS_CLK2) for McASP3 AHCLKX clock as well.
SYS_CLK2 is sourced from an external oscillator running 22.5792MHz and it
is coming in to the SoC via the X1_OSC1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3efda00129 ("ARM: dts: am335x: replace gpio-key,wakeup with
wakeup-source property") replaces all the legacy "gpio-key,wakeup" with
the unified "wakeup-source" property to prevent any further copy-paste
duplication.
However couple of use of these legacy property sneaked in during the
merge window. This patch replaces them too.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LOCK key is at KSO9/KSI3 for Chromebook Flip and other devices
that use the Chrome OS EC keyboard matrix.
Signed-off-by: James Chao <james_chao@asus.com>
Signed-off-by: YH Huang <yh.huang@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Keyboard driver for GPIO buttons(gpio-keys) checks for the legacy
"gpio-key,wakeup" boolean property to enable gpio buttons as wakeup
source.
Few dts files assign value "1" to gpio-key,wakeup and in one instance a
value "0" is assigned probably assuming it won't be enabled as a wakeup
source. Since the presence of the boolean property indicates it is
enabled, value of "0" have no value.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property which inturn fixes the above mentioned issue.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 75, 110, 1152000, 1500000, 2000000, and
4000000 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000 bps.
- HSCIF:
- Supports now 50, 75, 110, 134, 150, and 200 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000, 1152000, 3000000, 3500000, and 4000000
bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (S1 and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF device nodes.
This increases the range and accuracy of supported baud rates on SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (S1 and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF device nodes.
This increases the range and accuracy of supported baud rates on SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in emev2 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in sh73a0 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use GIC_* defines for GIC interrupt cells in r7s72100 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the otg/drc usb controller on the Olimex A20 EVB.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Enable the otg/drc usb controller on the MK808C.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Setup the USB controller and configure it to operate in host mode.
Additionally add the USB phy node for the ZYBO, including reset gpio
which is connected to a external MIO pin.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add dts file to support Buffalo Linkstation LS-GL
(a.k.a Buffalo Linkstation Pro/Live), which is marvell orion5x based
3.5" HDD NAS.
Product info:
- (JPN) http://buffalo.jp/products/catalog/item/l/ls-gl/
- (ENG) http://www.buffalotech.com/products/network-storage/linkstation/linkstation-pro
This device tree is based on the board file:
arch/arm/mach-orion5x/kurobox_pro-setup.c
However, that board file also support Kurobox Pro, which is not supported by
device tree yet. So the board file is not removed.
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In order to support more linkstation devices, common part of current
.dts file goes into .dtsi file. Some .dtsi start with "mvebu-" prefix
because other kirkwood based linkstation devices are similar, and
will be migrated to use these .dtsi some time later.
- orion5x-linkstation.dtsi
- mvebu-linkstation-fan.dtsi
- mvebu-linkstation-gpio-simple.dtsi
while all rest part remains in device specific .dts file:
- orion5x-linkstation-lswtgl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds some comments to the Armada 385 AP Device Tree
description to indicate which Ethernet interface matches which
physical connector on the board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Armada 38x, the available network interfaces are:
- port 0, at 0x70000
- port 1, at 0x30000
- port 2, at 0x34000
Due to the rule saying that DT nodes should be ordered by register
addresses, the network interfaces are probed in this order:
- port 1, at 0x30000, which gets named eth0
- port 2, at 0x34000, which gets named eth1
- port 0, at 0x70000, which gets named eth2
(if all three ports are enabled at the board level)
Unfortunately, the network subsystem doesn't provide any way to rename
network interfaces from the kernel (it can only be done from
userspace). So, the default naming of the network interfaces is very
confusing as it doesn't match the datasheet, nor the naming of the
interfaces in the bootloader, nor the naming of the interfaces on
labels printed on the board.
For example, on the Armada 388 GP, the board has two ports, labelled
GE0 and GE1. One has to know that GE0 is eth1 and GE1 is eth0, which
isn't really obvious.
In order to solve this, this patch proposes to exceptionaly violate
the rule of "order DT nodes by register address", and put the 0x70000
node before the 0x30000 node, so that network interfaces get named in
a more natural way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MTD flash stores u-boot and u-boot environment on linkstation lswtgl.
The latter one can be easily read/write by u-boot-tools package in Debian.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix audio on kirkwood-openrd-client:
1) The audio-controller was left disabled.
2) The probe fails because cs42l51 is missing #sound-dai-cells.
/sound/simple-audio-card,codec: could not get #sound-dai-cells for /ocp@f1000000/i2c@11000/cs42l51@4a
asoc-simple-card sound: parse error -22
asoc-simple-card: probe of sound failed with error -22
3) The mapping is incorrect:
asoc-simple-card sound: cs42l51-hifi <-> spdif mapping ok
should be:
asoc-simple-card sound: cs42l51-hifi <-> i2s mapping ok
Reported-by: Rick Thomas <rbthomas@pobox.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Rick Thomas <rbthomas@pobox.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Some OpenRD boards have RS-232 and RS-486 connectors wired, but using them
needs a custom DTB as the current DTB configures SD card slot instead.
This patch adds documentation into the DTS on how to change
the configuration.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
- LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
- There're two red LED indicator on LS-WVL to show when HDD fails,
which is similar to LS-WXL, but there's no such on LS-VL.
So after the split, common part goes into .dtsi file:
- kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
- kirkwood-linkstation-lsvl.dts
- kirkwood-linkstation-lswvl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
- There're two red LED indicator on LS-WXL to show when HDD fails,
but there's no such on LS-WSXL.
- There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.
So after the split, common part goes into .dtsi file:
- kirkwood-linkstation.dtsi
- kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
- kirkwood-linkstation-lswsxl.dts
- kirkwood-linkstation-lswxl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The SD card slot was enabled by default with legacy booting.
It does not work anymore with DT boot. Fix by providing GPIO configuration
that matches the old default.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The UART/SD pin names are swapped, fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the commit a526973e02 ("pinctrl: mvebu: Fix mapping of pin
63 (gpo -> gpio)"), the mpp63 is no more declared as a GPO but is a
GPIO. Even if in the datasheet this pin is described as GPO, the
experience of the D-Link DNS-327L board shows that it can be used as a
GPIO.
This commits generated warnings for the board using this pin as gpo, with
this patch the dts are fixed by using the new function (gpio) instead of
the old one.
The binding documentation has also been updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Using the usb-nop-xceiv PHY for the xhci nodes allows a better
representation of the hardware but also a better handling of the
regulator. By linking the regulator to the PHY there is no more need to
use the regulator-always-on property, then it allows a better power
management.
The remaining usb node uses the ehci-orion driver which can't be used
with the usb-nop-xceiv PHY and must keeps the direct link to the
regulator with the regulator-always-on property.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Really, what we meant by regulator-always-on is that the regulators
are already turned on by the bootloader, for which regulator-boot-on
is a better description.
A net advantage of using regulator-boot-on is that the regulator is
not touched at boot time by the kernel, which avoids having the hard
drives spinning down and then up again, taking several (~5) seconds of
additional boot time.
In addition, there is no need to have such properties on the child
regulators used for SATA. Having it on the parent regulator that
really controls the GPIO is sufficient.
Without the patch:
[ 3.945866] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.995862] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.005863] ata4: SATA link down (SStatus 0 SControl 300)
[ 9.125861] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 9.144575] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 9.151471] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
(and you can hear the disk spinning down and up during this 5.1
seconds delay)
With the patch:
[ 3.945988] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.005980] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.011404] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.145978] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.153701] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 4.160597] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As the name of the Device Tree file name suggests, the Armada 388 GP
really contains an Armada 388 SoC, so this commit updates the board
name and compatible string in the Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pl330 integrated in rk3036 platform that doesn't support
DMAFLUSHP function. So we add 'arm,pl330-broken-no-flushp' quirk
for rk3036.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pl330 integrated in rk3xxx platform doesn't support
DMAFLUSHP function. So we add arm,pl330-broken-no-flushp quirk
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pl330 integrated in rk3288 platform doesn't support
DMAFLUSHP function. So we add arm,pl330-broken-no-flushp quirk
for it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pinctrl-sunxi uses 3 cells to describe interrupt, not 2. It's bank
number, pin number and flags.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to latest schematics [1], GPIO_1/VBUSDET
on TPS659038 is tied to AM57x GPIO4_21. We can use
that as a VBUS interrupt, instead of relying on
PMIC's VBUS interrupts which don't seem to be firing
on x15 at all.
A follow up patch will add support for using this
GPIO-based interrupt mechanism for notifying about
VBUS.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
[cw00.choi: Use the 'vbus-gpio' property instead of 'interrupts-extended']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
According to latest schematics [1], this board
leaves ID pin floating. It's not connected to
anything at all.
So let's remove it.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The A83T does not have a 32.768 kHz low speed oscillator, either as
an external crystal or input. It has a 16 MHz RC-based (inaccurate)
internal oscillator, which is then divided by 512 for a clock close
to 32 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This connects the USB driver to the USB power domain, so that USB can
actually be turned on at boot if the bootloader didn't do it for us.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
This one is essentially the same as revision 2 B board (with the I2S on
P5 header).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on bcm2835.dtsi -> bcm283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch fixes the naming of the device tree node: uart@7e201000
to conform to the standard of: serial@7e201000
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables the use of the auxiliary spi1 and spi2 devices
on the bcm2835 SOC.
Note that this requires the use of the new clk-bcm2835-aux to work.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
If we playback the 8KHz FS audio with the 256 mclk_fs, we need the
mclk = 256 * 8000 = 2.048MHz, the frac div is 594 / 2.048 = 290,
the frac div value 0x00809015 set to the CRU_CLKSEL7_CON will cause
to hang.
We increase the mclk_fs to 512, will get the mclk = 512 * 8000 =
4.096MHz, use 0x01009015 instead of 0x00809015 to work around this
issue. We will keep tracking it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the needed spi node for rk3036 dts.
We have to use the 4 bus emmc to work if someone want to support
the spi devices, since the pins are re-used by emmc data[5-8] and spi.
In some caseswe need to support the spi devices, that will waste the
emmc performance.
Moment, the kylin/evb hasn't the spi devices to work, so maybe we need wait
the new required to enable in kylin/evb board.
Anyway, the spi should be needed land in rk3036 dts.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The I2S block that provide the output clock as the mclk for rt5616,
That will be the master clock input.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i2c3 and uart4 are available on the GPIO header. Though these pins only
have this one special function, the user may choose to use them as GPIOs
instead.
Since our policy is not to choose what function to present on the GPIO
headers of development boards, remove them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NqvQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
As the kylin schematic drawing, add the needed work led for
kylin board.
Run:
echo 0 > /sys/class/leds/kylin:red:led/brightness
echo 1 > /sys/class/leds/kylin:red:led/brightness
The led can normal on/off on kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable audio DMAC (= rcar-dmac) in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v4
* Use GIC_SPI in interrupts properties
Enable DMA transfer using DVC in r8a7793/gose device tree.
DMA DMApp
[MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SRC in r8a7793/gose device tree.
DMA DMApp
[MEM] -> [SRC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [SRC] <- [SSIU] <- [SSI]
Current sound driver is supporting
SSI/SRC random connection.
So, this patch is tring
SSI0 -> SRC2
SSI1 <- SRC3
Based on similar work for the r8a7791/koeslch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SSIU in gose/r8a7791 device tree.
DMA
[MEM] -> [SSIU] -> [SSI]
DMA
[MEM] <- [SSIU] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SSI in r8a7793/gose device tree.
DMA
[MEM] -> [SSI]
DMA
[MEM] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable sound PIO support in the r8a7793/gose device tree.
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Base on work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two Audio DMA controllers in the r8a7791 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate Audio DMA clocks in the r8a7791 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DVC support to sound node in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate R-Car sound node in r8a7793 device tree.
This only supports PIO transfers.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare m2 clock in r8a7793 device tree.
Based on similar work for the r8a7791 by Laurent Pinchart.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate audio clock in r8a7793 device tree.
audio_clk_a/b/c are required for R-Car sound.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate MSTP10 clocks in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
