according datasheet both chips can erase 4kByte sectors individually
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some spi-nor drivers perform sector erase by duplicating their
write_reg() command. Let's not require that the driver fill this out,
and provide a default instead.
Tested on m25p80.c and Medatek's MT8173 SPI NOR flash driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->priv field of the mtd_info object attached to a nand_chip device
should point to the nand_chip device. The pxa and cafe drivers are
assigning this field their own private structure, which works fine as long
as the nand_chip field is the first one in the driver private struct but
seems a bit fragile.
Fix that by setting mtd->priv to point the nand_chip field and assigning
chip->priv to the private structure head.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
AFAIR this driver was never tested with subpage read support, and this
code is currently unused because we don't set the NAND_SUBPAGE_READ
flag. It can be resurrected if someone tests it properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ray Jui <rjui@broadcom.com>
The read_byte() handling for accessing the flash cache has some awkward
swapping being done in the read_byte() function. Let's just make this a
byte array, and do the swapping with the word-level macros during the
initial buffer copy.
This is just a refactoring patch, with no (intended) functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Clay McClure <clay@daemons.net>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Tested-by: Clay McClure <clay@daemons.net>
It is theoretically possible to probe this driver without a matching
device tree, so let's guard against this.
Also, use the of_device_get_match_data() helper to make this a bit
simpler.
Coverity complained about this one.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Doing a bit-or operation with zero is pointless.
Remove this unneeded bit-or.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NAND clock can be disabled on suspend and enabled on resume.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This macro is not used anymore, so it's just dead code.
Remove it.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently, the driver is trying to detect the presence of a chip
by issuing a RESET command before nand_scan_ident. This seems completely
redundant, and is also a layering violation as nand_scan_ident is in charge
of device detection.
This commit removes the RESET command use, and moves the initial
timing configuration to pxa3xx_nand_config_ident.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.
Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.
Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transfered data.
However, the initial chunk size is used in a non-splitted way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).
Thus, the initial chunk size should be 2048 as well.
On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:
[..]
pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
pxa3xx-nand f10d0000.nand: Wait time out!!!
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
nand: Micron MT29F8G08ABABAWP
nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If multiple NAND chips are registered to the same controller, then when
rebooting the system, the first one will grab the controller lock, while
the second will wait forever for the first one to release it. i.e., a
classic deadlock.
This problem was solved for a similar case (suspend/resume) back in
commit 6b0d9a8412 ("mtd: nand: fix multi-chip suspend problem"), and
the shutdown state really isn't much different for us, so rather than
adding a new special case to nand_get_device(), we can just overload the
FL_PM_SUSPENDED state.
Now, multiple chips can "get" the same controller lock (preventing
further I/O), while we still allow other chips to pass through
nand_shutdown().
Original report:
http://thread.gmane.org/gmane.linux.drivers.mtd/59726http://lists.infradead.org/pipermail/linux-mtd/2015-July/059992.html
Fixes: 72ea403669 ("mtd: nand: added nand_shutdown")
Reported-by: Andrew E. Mileski <andrewm@isoar.ca>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Andrew E. Mileski <andrewm@isoar.ca>
Acked-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fallout from commit 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
We see errors like this:
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_detect_bank':
drivers/mtd/nand/jz4740_nand.c:340:9: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:340:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/jz4740_nand.c:359:2: error: implicit declaration of function 'jz_gpio_set_function' [-Werror=implicit-function-declaration]
drivers/mtd/nand/jz4740_nand.c:359:29: error: 'JZ_GPIO_FUNC_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:399:29: error: 'JZ_GPIO_FUNC_NONE' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_probe':
drivers/mtd/nand/jz4740_nand.c:528:13: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_remove':
drivers/mtd/nand/jz4740_nand.c:555:14: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
Patched similarly to:
https://patchwork.linux-mips.org/patch/11089/
Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's easier to guarantee we've cleared out all unused fields with
memset() than by manually initializing each field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We now stick the device node representing the current MTD (if any) into
sysfs, so let's make sure we have a reference to it before doing that.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If there is more than one map region for this device, then the
concatenated MTD will not have a parent device assigned to it -- only
the sub-devices (which are not actually registered with the framework)
will have their parents assigned. Let's assign the concatenated device
correctly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This field is no longer used anywhere, as it is superseded by
mtd->dev.of_node.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We should assign the MTD dev.of_node instead of the parser data field.
This gets us the equivalent partition parser behavior with fewer special
fields and parameter passing.
Also convert several of these to mtd_device_register(), since we don't
need the 2nd and 3rd parameters anymore.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We can just alias to the MTD of_node.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the SPI-NOR/MTD framework pass the 'flash_node' through to the
partition parsing code, we don't have to do it ourselves.
Also convert to mtd_device_register(), since we don't need the 2nd and
3rd parameters anymore.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All of these drivers set up a parser data struct just to communicate DT
partition data. This field has been deprecated and is instead supported
by telling nand_scan_ident() about the 'flash_node'.
This patch:
* sets chip->flash_node for those drivers that didn't already (but used
OF partitioning)
* drops the parser data
* switches to the simpler mtd_device_register() where possible, now
that we've eliminated one of the auxiliary parameters
Now that we've assigned chip->flash_node for these drivers, we can
probably rely on nand_dt_init() to do more of the DT parsing for us, but
for now, I don't want to fiddle with each of these drivers. The parsing
is done in duplicate for now on some drivers. I don't think this should
break things. (Famous last words.)
(Rolled in some changes by Boris Brezillon)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Used semantic patch with 'make coccicheck MODE=patch COCCI=script.cocci':
---8<----
virtual patch
@@
struct spi_nor b;
struct spi_nor *c;
expression d;
@@
(
-(b).flash_node = (d)
+spi_nor_set_flash_node(&b, d)
|
-(c)->flash_node = (d)
+spi_nor_set_flash_node(c, d)
)
---8<----
And a manual conversion for the one use of spi_nor_get_flash_node().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We should pass along our flash DT node to the MTD layer, so it can set
up ofpart for us.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
It seems more logical to use a device node directly associated with the
MTD master device (i.e., mtd->dev.of_node field) rather than requiring
auxiliary partition parser information to be passed in by the driver in
a separate struct.
This patch supports the mtd->dev.of_node field and deprecates the parser
data 'of_node' field
Driver conversions may now follow.
Additional side benefit to assigning mtd->dev.of_node rather than using
parser data: the driver core will automatically create a device -> node
symlink for us.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Return immediately if we are not finding a valid v1 partition
in afs_read_footer_v1(), invert scanning logic so we continue
to read image information on v1 if we found a footer. This is
needed for the logic we introduce to parse v2 footers.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Break out the magic number to a #defined constant.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ARM use their special partitions also on the ARM64 architecture
reference designs, so enable this for ARM64.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since we're gonna add the v2 version of flash information
structure and we want to avoid confusion, rename the old
functions to *v1. Cut the word "structure" from the struct
name, it is pretty obvious that it is a struct already from
the keyword.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* access time support for UBIFS by Dongsheng Yang
* random cleanups and bug fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9n2S
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.4-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
- access time support for UBIFS by Dongsheng Yang
- random cleanups and bug fixes all over the place
* tag 'upstream-4.4-rc1' of git://git.infradead.org/linux-ubifs:
ubifs: introduce UBIFS_ATIME_SUPPORT to ubifs
ubifs: make ubifs_[get|set]xattr atomic
UBIFS: Delete unnecessary checks before the function call "iput"
UBI: Remove in vain semicolon
UBI: Fastmap: Fix PEB array type
UBIFS: Fix possible memory leak in ubifs_readdir()
fs/ubifs: remove unnecessary new_valid_dev check
ubi: fastmap: Implement produce_free_peb()
UBIFS: print verbose message when rescanning a corrupted node
UBIFS: call dbg_is_power_cut() instead of reading c->dbg->pc_happened
UBI: drop null test before destroy functions
UBI: Update comments to reflect UBI_METAONLY flag
UBI: Fix debug message
UBI: Fix typo in comment
UBI: Fastmap: Simplify expression
UBIFS: fix a typo in comment of ubifs_budget_req
UBIFS: use kmemdup rather than duplicating its implementation
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PEB array is an array of __be32, so let's fix the
scan_pool() prototype accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Core
* WARN (in some cases) when a struct mtd_info is registered multiple times;
in the past this was "supported", but it's still error prone for future
development. There's only one ugly case of this left in the tree (that
we're aware of) and the owners are aware of the problems there.
* fix potential deadlock in the blkdev removal path
NOTE: the (potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
* ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user space
vs. 64-bit kernel space
* Set MTD parent device correctly throughout the tree, so the tree structure
appears correctly in sysfs; many drivers were missing this (soft)
requirement
* Move device tree partitions (ofpart) into a dedicated 'partitions' subnode;
this helps to disambiguate whether a node is a partition or some other
auxiliary data
* Improve error handling for partitioning failures
NAND
* General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
* Fix OF-based autoloading of several NAND drivers when built as modules
* pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
* brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND chips)
* sunxi_nand: refactoring and a few bug fixes
* vf610: new NAND driver
* FSMC: add SW BCH support; support common NAND DT bindings
* lpc32xx_slc: refactor and improve timing calculations logic
* denali: support for rev 5.1
SPI NOR
* Layering improvements
* Added Winbond lock/unlock support
* Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
* Increase full-chip-erase timeout linearly with flash size
* fsl-quadspi: fix compile for non-ARM architectures
* New flash support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UzSW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Core:
- WARN (in some cases) when a struct mtd_info is registered multiple
times; in the past this was "supported", but it's still error prone
for future development. There's only one ugly case of this left in
the tree (that we're aware of) and the owners are aware of the
problems there.
- fix potential deadlock in the blkdev removal path NOTE: the
(potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
- ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user
space vs 64-bit kernel space
- Set MTD parent device correctly throughout the tree, so the tree
structure appears correctly in sysfs; many drivers were missing
this (soft) requirement
- Move device tree partitions (ofpart) into a dedicated 'partitions'
subnode; this helps to disambiguate whether a node is a partition
or some other auxiliary data
- Improve error handling for partitioning failures
NAND:
- General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
- Fix OF-based autoloading of several NAND drivers when built as
modules
- pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
- brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND
chips)
- sunxi_nand: refactoring and a few bug fixes
- vf610: new NAND driver
- FSMC: add SW BCH support; support common NAND DT bindings
- lpc32xx_slc: refactor and improve timing calculations logic
- denali: support for rev 5.1
SPI NOR:
- Layering improvements
- Added Winbond lock/unlock support
- Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
- Increase full-chip-erase timeout linearly with flash size
- fsl-quadspi: fix compile for non-ARM architectures
- New flash support"
* tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd: (169 commits)
mtd: don't WARN about overloaded users of mtd->reboot_notifier.notifier_call
mtd: nand: sunxi: avoid retrieving data before ECC pass
mtd: nand: sunxi: fix sunxi_nfc_hw_ecc_read/write_chunk()
mtd: blkdevs: fix potential deadlock + lockdep warnings
mtd: ofpart: move ofpart partitions to a dedicated dt node
doc: dt: mtd: support partitions in a special 'partitions' subnode
mtd: brcmnand: Force 8bit mode before doing nand_scan_ident()
mtd: brcmnand: factor out CFG and CFG_EXT bitfields
mtd: mtdpart: Do not fail mtd probe when parsing partitions fails
mtd: fsl-quadspi: fix macro collision problems with READ/WRITE
mtd: warn when registering the same master many times
mtd: fixup corner case error handling in mtd_device_parse_register()
mtd: tests: Replace timeval with ktime_t
mtd: fsmc_nand: Add BCH4 SW ECC support for SPEAr600
mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper
mtd: nand: increase ready wait timeout and report timeouts
mtd: docg3: off by one in doc_register_sysfs()
mtd: pxa3xx_nand: clean up the pxa3xx timings
mtd: pxa3xx_nand: rework flash detection and timing setup
mtd: pxa3xx_nand: add helpers to setup the timings
...
There are multiple types of users of mtd->reboot_notifier.notifier_call:
(1) A while back, the cfi_cmdset_000{1,2} chip drivers implemented a
reboot notifier to (on a best effort basis) attempt to reset their flash
chips before rebooting.
(2) More recently, we implemented a common _reboot() hook so that MTD
drivers (particularly, NAND flash) could better halt I/O operations
without having to reimplement the same notifier boilerplate.
Currently, the WARN_ONCE() condition here was written to handle (2), but
at the same time it mis-diagnosed case (1) as an already-registered MTD.
Let's fix this by having the WARN_ONCE() condition better imitate the
condition that immediately follows it. (Wow, I don't know how I missed
that one.)
(Side note: Unfortunately, we can't yet combine the reboot notifier code
for (1) and (2) with a patch like [1], because some users of (1) also
use mtdconcat, and so the mtd_info struct from cfi_cmdset_000{1,2} won't
actually get registered with mtdcore, and therefore their reboot
notifier won't get registered.)
[1] http://patchwork.ozlabs.org/patch/417981/
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jesper Nilsson <jespern@axis.com>
Cc: linux-cris-kernel@axis.com
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The in-band data are copied twice: before ECC correction and after the
ECC engine has fixed all the fixable bitflips.
Drop the useless memcpy_fromio operation by passing a NULL pointer when
calling sunxi_nfc_read_buf().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions try to avoid changing
the column address if unnecessary, but the logic to determine whether it's
necessary or not is currently wrong: it adds the ecc->bytes value to the
current offset where it should actually add ecc->size.
Fixes: 913821bdd2 ("mtd: nand: sunxi: introduce sunxi_nfc_hw_ecc_read/write_chunk()")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 073db4a51e ("mtd: fix: avoid race condition when accessing
mtd->usecount") fixed a race condition but due to poor ordering of the
mutex acquisition, introduced a potential deadlock.
The deadlock can occur, for example, when rmmod'ing the m25p80 module, which
will delete one or more MTDs, along with any corresponding mtdblock
devices. This could potentially race with an acquisition of the block
device as follows.
-> blktrans_open()
-> mutex_lock(&dev->lock);
-> mutex_lock(&mtd_table_mutex);
-> del_mtd_device()
-> mutex_lock(&mtd_table_mutex);
-> blktrans_notify_remove() -> del_mtd_blktrans_dev()
-> mutex_lock(&dev->lock);
This is a classic (potential) ABBA deadlock, which can be fixed by
making the A->B ordering consistent everywhere. There was no real
purpose to the ordering in the original patch, AFAIR, so this shouldn't
be a problem. This ordering was actually already present in
del_mtd_blktrans_dev(), for one, where the function tried to ensure that
its caller already held mtd_table_mutex before it acquired &dev->lock:
if (mutex_trylock(&mtd_table_mutex)) {
mutex_unlock(&mtd_table_mutex);
BUG();
}
So, reverse the ordering of acquisition of &dev->lock and &mtd_table_mutex so
we always acquire mtd_table_mutex first.
Snippets of the lockdep output follow:
# modprobe -r m25p80
[ 53.419251]
[ 53.420838] ======================================================
[ 53.427300] [ INFO: possible circular locking dependency detected ]
[ 53.433865] 4.3.0-rc6 #96 Not tainted
[ 53.437686] -------------------------------------------------------
[ 53.444220] modprobe/372 is trying to acquire lock:
[ 53.449320] (&new->lock){+.+...}, at: [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc
[ 53.457271]
[ 53.457271] but task is already holding lock:
[ 53.463372] (mtd_table_mutex){+.+.+.}, at: [<c0439994>] del_mtd_device+0x18/0x100
[ 53.471321]
[ 53.471321] which lock already depends on the new lock.
[ 53.471321]
[ 53.479856]
[ 53.479856] the existing dependency chain (in reverse order) is:
[ 53.487660]
-> #1 (mtd_table_mutex){+.+.+.}:
[ 53.492331] [<c043fc5c>] blktrans_open+0x34/0x1a4
[ 53.497879] [<c01afce0>] __blkdev_get+0xc4/0x3b0
[ 53.503364] [<c01b0bb8>] blkdev_get+0x108/0x320
[ 53.508743] [<c01713c0>] do_dentry_open+0x218/0x314
[ 53.514496] [<c0180454>] path_openat+0x4c0/0xf9c
[ 53.519959] [<c0182044>] do_filp_open+0x5c/0xc0
[ 53.525336] [<c0172758>] do_sys_open+0xfc/0x1cc
[ 53.530716] [<c000f740>] ret_fast_syscall+0x0/0x1c
[ 53.536375]
-> #0 (&new->lock){+.+...}:
[ 53.540587] [<c063f124>] mutex_lock_nested+0x38/0x3cc
[ 53.546504] [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc
[ 53.552606] [<c043f164>] blktrans_notify_remove+0x7c/0x84
[ 53.558891] [<c04399f0>] del_mtd_device+0x74/0x100
[ 53.564544] [<c043c670>] del_mtd_partitions+0x80/0xc8
[ 53.570451] [<c0439aa0>] mtd_device_unregister+0x24/0x48
[ 53.576637] [<c046ce6c>] spi_drv_remove+0x1c/0x34
[ 53.582207] [<c03de0f0>] __device_release_driver+0x88/0x114
[ 53.588663] [<c03de19c>] device_release_driver+0x20/0x2c
[ 53.594843] [<c03dd9e8>] bus_remove_device+0xd8/0x108
[ 53.600748] [<c03dacc0>] device_del+0x10c/0x210
[ 53.606127] [<c03dadd0>] device_unregister+0xc/0x20
[ 53.611849] [<c046d878>] __unregister+0x10/0x20
[ 53.617211] [<c03da868>] device_for_each_child+0x50/0x7c
[ 53.623387] [<c046eae8>] spi_unregister_master+0x58/0x8c
[ 53.629578] [<c03e12f0>] release_nodes+0x15c/0x1c8
[ 53.635223] [<c03de0f8>] __device_release_driver+0x90/0x114
[ 53.641689] [<c03de900>] driver_detach+0xb4/0xb8
[ 53.647147] [<c03ddc78>] bus_remove_driver+0x4c/0xa0
[ 53.652970] [<c00cab50>] SyS_delete_module+0x11c/0x1e4
[ 53.658976] [<c000f740>] ret_fast_syscall+0x0/0x1c
[ 53.664621]
[ 53.664621] other info that might help us debug this:
[ 53.664621]
[ 53.672979] Possible unsafe locking scenario:
[ 53.672979]
[ 53.679169] CPU0 CPU1
[ 53.683900] ---- ----
[ 53.688633] lock(mtd_table_mutex);
[ 53.692383] lock(&new->lock);
[ 53.698306] lock(mtd_table_mutex);
[ 53.704658] lock(&new->lock);
[ 53.707946]
[ 53.707946] *** DEADLOCK ***
Fixes: 073db4a51e ("mtd: fix: avoid race condition when accessing mtd->usecount")
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org>
Parsing direct subnodes of a mtd device as partitions is unreliable
since the mtd device is also part of its bus subsystem and can contain
bus data in subnodes.
Move ofpart data to a subnode of its own so it is clear which data is
part of the partition layout.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Just like other NAND controllers, the NAND READID command only works
in 8bit mode for all versions of BRCMNAND controller.
This patch forces 8bit mode for each NAND CS in brcmnand_init_cs()
before doing nand_scan_ident() to ensure that BRCMNAND controller
is in 8bit mode when NAND READID command is issued.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use enum instead of magic numbers for CFG and CFG_EXT bitfields.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Anup Patel <anup.patel@broadcom.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to wrong assumption in ofpart ofpart fails on Exynos on SPI chips
with no partitions because the subnode containing controller data
confuses the ofpart parser.
Thus compiling in ofpart support automatically fails probing any SPI NOR
flash without partitions on Exynos.
Compiling in a partitioning scheme should not cause probe of otherwise
valid device to fail.
Instead, let's do the following:
* try parsers until one succeeds
* if no parser succeeds, report the first error we saw
* even in the failure case, allow MTD to probe, with fallback
partitions or no partitions at all -- the master device will still be
registered
Issue report and comments initially by Michal Suchanek.
Reported-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the READ/WRITE to FSL_READ/FSL_WRITE to resolve any possible
namespace collisions with READ/WRITE macros (e.g., from <linux/fs.h>).
Problems have been seen, for example, on mips:
>> drivers/mtd/spi-nor/fsl-quadspi.c:186:5: error: 'LUT_0' undeclared (first use in this function)
((LUT_##ins) << INSTR0_SHIFT))
^
>> drivers/mtd/spi-nor/fsl-quadspi.c:188:30: note: in expansion of macro 'LUT0'
On SPARC:
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
drivers/mtd/spi-nor/fsl-quadspi.c:369:1: error: 'LUT_0' undeclared (first use in this function)
drivers/mtd/spi-nor/fsl-quadspi.c:418:1: error: pasting "LUT_" and "(" does not give a valid preprocessing token
drivers/mtd/spi-nor/fsl-quadspi.c:418:2: error: implicit declaration of function 'LUT_'
And surely on others.
Fixes: d26a22d067 ("mtd: fsl-quadspi: allow building for other ARCHes with COMPILE_TEST")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: rewrote commit description]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When CONFIG_MTD_PARTITIONED_MASTER=y, it is fatal to call
mtd_device_parse_register() twice on the same MTD, as we try to register
the same device/kobject multipile times.
When CONFIG_MTD_PARTITIONED_MASTER=n, calling
mtd_device_parse_register() is more of just a nuisance, as we can mostly
navigate around any conflicting actions.
But anyway, doing so is a Bad Thing (TM), and we should complain loudly
for any drivers that try to do this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Since commit 3efe41be22 ("mtd: implement common reboot notifier
boilerplate"), we might try to register a reboot notifier for an MTD
that failed to register. Let's avoid this by making the error path
clearer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Changes the 32-bit time type timeval to the 64-bit time type
ktime_t, since 32-bit systems using struct timeval will break in the
year 2038. Correspondingly change do_gettimeofday() to ktime_get()
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval.Here, ktime_get() is used instead of ktime_get_real()
since ktime_get() uses monotonic clock.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your nand controller
DT node:
nand-ecc-mode = "soft_bch";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If nand_wait_ready() times out, this is silently ignored, and its
caller will then proceed to read from/write to the chip before it is
ready. This can potentially result in corruption with no indication as
to why.
While a 20ms timeout seems like it should be plenty enough, certain
behaviour can cause it to timeout much earlier than expected. The
situation which prompted this change was that CPU 0, which is
responsible for updating jiffies, was holding interrupts disabled
for a fairly long time while writing to the console during a printk,
causing several jiffies updates to be delayed. If CPU 1 happens to
enter the timeout loop in nand_wait_ready() just before CPU 0 re-
enables interrupts and updates jiffies, CPU 1 will immediately time
out when the delayed jiffies updates are made. The result of this is
that nand_wait_ready() actually waits less time than the NAND chip
would normally take to be ready, and then read_page() proceeds to
read out bad data from the chip.
The situation described above may seem unlikely, but in fact it can be
reproduced almost every boot on the MIPS Creator Ci20.
Therefore, this patch increases the timeout to 400ms. This should be
enough to cover cases where jiffies updates get delayed. In nand_wait()
the timeout was previously chosen based on whether erasing or
programming. This is changed to be 400ms unconditionally as well to
avoid similar problems there. nand_wait() is also slightly refactored
to be consistent with nand_wait{,_status}_ready(). These changes should
have no effect during normal operation.
Debugging this was made more difficult by the misleading comment above
nand_wait_ready() stating "The timeout is caught later" - no timeout was
ever reported, leading me away from the real source of the problem.
Therefore, a pr_warn() is added when a timeout does occur so that it is
easier to pinpoint similar problems in future.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Smatch found a bug in the error handling:
drivers/mtd/devices/docg3.c:1634 doc_register_sysfs()
error: buffer overflow 'doc_sys_attrs' 4 <= 4
The problem is that if the very last device_create_file() fails, then we
are beyond the end of the array. Actually, any time i == 3 then there
is a problem. We can fix this an simplify the code at the same time by
moving the !ret conditions out of the for loops and using a goto
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the previous modifications, lots of pxa3xx specific definitions can
be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Rework the pxa3xx_nand driver to allow using functions exported by the
nand framework to detect the flash and the timings. Then setup the
timings using the helpers previously added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helpers to setup the timings in the pxa3xx driver. These helpers
allow to either make use of the nand framework nand_sdr_timings or the
pxa3xx specific pxa3xx_nand_host, for compatibility reasons.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using readsl() result in a build error on i386. Fix this by using
ioread32_rep() instead, to allow compile testing the pxa3xx nand driver
on other architectures later.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #206
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x208/0x248)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #201
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x290/0x568)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We got the syntax wrong here. Compile tested this time!
Error:
drivers/mtd/maps/rbtx4939-flash.c: In function 'rbtx4939_flash_probe':
>> drivers/mtd/maps/rbtx4939-flash.c:99:11: error: request for member 'dev' in something not a structure or union
info->mtd.dev.parent = &dev->dev;
^
Fixes: 9aa7e50276 ("mtd: maps: rbtx4939-flash: show parent device in sysfs")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Frans Klaver <fransklaver@gmail.com>
We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The old PM model is deprecated. This is equivalent.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mtd_{suspend,resume}() get called from mtdcore in a class suspend/resume
callback. We don't need to call them again here. In practice, this would
actually work OK, as nand_base actually handles nesting OK -- it just
might print warnings.
Untested, but there are few (no?) users of PM for this driver AFAIK.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Building for x86 results in the following build errors:
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
>> drivers/mtd/spi-nor/fsl-quadspi.c:355:21: error: 'SZ_16M' undeclared (first use in this function)
if (q->nor_size <= SZ_16M) {
^
drivers/mtd/spi-nor/fsl-quadspi.c:355:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
>> drivers/mtd/spi-nor/fsl-quadspi.c:208:27: error: 'SZ_4M' undeclared (first use in this function)
#define QUADSPI_MIN_IOMAP SZ_4M
^
>> drivers/mtd/spi-nor/fsl-quadspi.c:845:25: note: in expansion of macro 'QUADSPI_MIN_IOMAP'
q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
Explicitly include <linux/sizes.h> to fix the problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't actually need ARCH_MXC to compile. Relax the
constraints.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Seen when compile-testing on non-32-bit arch:
CC drivers/mtd/spi-nor/fsl-quadspi.o
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
drivers/mtd/spi-nor/fsl-quadspi.c:873:2: warning: format '%d' expects argument of type 'int', but argument 6 has type 'size_t' [-Wformat=]
dev_dbg(q->dev, "cmd [%x],read from 0x%p, len:%d\n",
^
Also drop the '0x' prefixing to the '%p' formatter, since %p already
knows how to format pointers appropriately.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Many other flash share the same features as ST Micro. I've tested some
Winbond flash, so add them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This code was a bit sloppy, would produce a lot of copy-and-paste, and
did not always provide a sensible interface:
* It didn't validate the length for LOCK and the offset for UNLOCK, so
we were essentially discarding half of the user-supplied data and
assuming what they wanted to lock/unlock
* It didn't do very good error checking
* It didn't make use of the fact that this operation works on
power-of-two dimensions
So, rewrite this to do proper bit arithmetic rather than a bunch of
hard-coded condition tables. Now we have:
* More comments on how this was derived
* Notes on what is (and isn't) supported
* A more exendible function, so we could add support for other
protection ranges
* More accurate locking - e.g., suppose the top quadrant is locked (75%
to 100%); then in the following cases, case (a) will succeed but (b)
will not (return -EINVAL):
(a) user requests lock 3rd quadrant (50% to 75%)
(b) user requests lock 3rd quadrant, minus a few blocks (e.g., 50%
to 73%)
Case (b) *should* fail, since we'd have to lock blocks that weren't
requested. But the old implementation didn't know the difference and
would lock the entire second half (50% to 100%)
This refactoring work will also help enable the addition of
mtd_is_locked() support and potentially the support of bottom boot
protection (TB=1).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->read_xxx() methods are all passed the page number the NAND controller
is supposed to read, but ->write_xxx() do not have such a parameter.
This is a problem if we want to properly implement data
scrambling/randomization in order to mitigate MLC sensibility to repeated
pattern: to prevent bitflips in adjacent pages in the same block we need
to avoid repeating the same pattern at the same offset in those pages,
hence the randomizer/scrambler engine need to be passed the page value
in order to adapt its seed accordingly.
Moreover, adding the page parameter to the ->write_xxx() methods add some
consistency to the current API.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Huang Shijie <shijie.huang@arm.com>
CC: Stefan Agner <stefan@agner.ch>
CC: devel@driverdev.osuosl.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner and name are automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Make sure the device structure is properly shown in sysfs by properly
filling in dev.parent.
While at it, make use of the default owner and name values set by
mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, take advantage of the default owner and name values set by
mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner and name set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner and name are automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Incidentally, it seems the owner field in the concatenated mtds is not
actually used, so this shouldn't make much of a difference anyway.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a parent device is set, add_mtd_device() has enough knowledge to fill
in some sane default values for the module name and owner. Do so if they
aren't already set.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
add_mtd_device() has a comment suggesting that the caller should have
set dev.parent. This is required to have the parent device symlink show
up in sysfs, but not for proper operation of the mtd device itself.
Currently we have five drivers registering mtd devices during module
initialization, so they don't actually provide a parent device to link
to. That means we cannot WARN_ON() here, as it would trigger false
positives.
Make the comment a bit less firm in its assertion that dev.parent should
be set.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The N25Q032A is identical to the N25Q032 except it has a different
supply voltage range. Therefore, it has a new JEDEC ID.
Signed-off-by: Aurelien Chanot <chanot.a@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The BRCM NAND driver can be re-used for Broadcom ARM64 SoCs hence
this patch updates Kconfig to allow selection of MTD_NAND_BRCMNAND
for ARM64.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should always type-cast pointer to "long" or "unsigned long"
because size of pointer is same as machine word size. This will
avoid pointer type-cast issues on both 32bit and 64bit systems.
This patch fixes pointer type-cast issue in brcmnand_write()
as-per above info.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation for deprecating ioremap_cache() convert its usage in
pxa2xx-flash to memremap.
Cc: David Woodhouse <dwmw2@infradead.org>
[brian: also convert iounmap to memunmap]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The probe of a mtd device can fail when a partition parser returns
error. The failure due to partition parsing can be quite mysterious when
multiple partitioning schemes are compiled in and any of them can fail
the probe.
Add debug prints which show what parsers were tried and what they
returned.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* mxc_nand: a "refactoring only" change in 4.3-rc1 had some bad pointer
(array) arithmetic. Fix that
* sunxi_nand:
- Fix an old list manipulation / memory management bug in the device
release() code path
- Correct a few mistakes in OOB write support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=A7qE
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151006' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"A few MTD fixes:
- mxc_nand: a "refactoring only" change in 4.3-rc1 had some bad
pointer (array) arithmetic. Fix that
- sunxi_nand:
- Fix an old list manipulation / memory management bug in the device
release() code path
- Correct a few mistakes in OOB write support"
* tag 'for-linus-20151006' of git://git.infradead.org/linux-mtd:
mxc_nand: fix copy_spare
mtd: nand: sunxi: fix sunxi_nand_chips_cleanup()
mtd: nand: sunxi: fix OOB handling in ->write_xxx() functions
According to LPC32xx User's Manual all values measured in clock cycles
are programmable from 1 to 16 clocks (4 bits) starting from 0 in
bitfield, the current version of calculated clock cycles is too
conservative.
Correctness of 0 bitfield value (i.e. programmed 1 clock
timing) is proven with actual NAND chip devices.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case if quotient of controller clock rate to device clock rate does
not fit into 4 bit value, choose the maximum acceptable value 0xF, which
stands for 16 clocks.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
No functional change, move bitfield calculations to macro
definitions with added clock rate argument, which are in turn defined
by new common SLCTAC_CLOCKS(c, n, s) macro definition.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If fastmap requests a free PEB for a pool and UBI is busy
with erasing PEBs we need to offer a function to wait for one.
We can reuse produce_free_peb() from the non-fastmap WL code
but with different locking semantics.
Cc: stable@vger.kernel.org # 4.1.x-
Reported-and-tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Richard Weinberger <richard@nod.at>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch trivially updates code comments to reflect the addition of the
UBI_METAONLY flag - as discussed https://lkml.org/lkml/2014/10/29/764
Cc: Richard Weinberger <richard@nod.at>
Cc: trivial@kernel.org
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
We have to use j instead of i. i is the volume id
and not the block.
Reported-by: Alexander.Block@continental-corporation.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Use the nand_check_erased_ecc_chunk() function to test if the ECC error
was triggered by an erased page containing a few bitflips.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
sunxi_nfc_user_data_to_buf() is exposed as an inline function, replace the
NFC_BUF_TO_USER_DATA() macro by an inline function to be consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ECC engine is protecting a few OOB bytes. Retrieve them from the
USER_DATA register instead of reading them in raw mode (ie without the ECC
protection).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helper functions to factorize the code dealing extra OOB bytes in the
normal and syndrome ECC implementations.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions have been created to
factorize the code in the normal and syndrome ECC implementation.
Make use of them where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The logic behind normal and syndrome ECC handling is pretty much the same,
the only difference is the ECC bytes placement.
Create two functions to read/write ECC chunks. Those functions will later
be used by the sunxi_nfc_hw_ecc_read/write_page() and
sunxi_nfc_hw_syndrome_ecc_read/write_page() functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The code used to enable/disable the hardware ECC engine is repeated in a
lot of places. Create two functions to avoid code duplication.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->init_size() hook was introduced to let NAND controller drivers
support NAND devices that could not be described in the nand_ids table.
Since then, the core has added support for extended-id parsing and
full-id description, thus allowing to describe pretty much all existing
NANDs.
Moreover, this hook is not used by any mainline driver, and should not be
used by new drivers, because detecting the NAND chip is not something
controller specific.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These really aren't needed, especially now that we embed the soc struct
in our private struct, so we can stash things there if needed.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Suffix mask macros with _MSK and add new helper macros to avoid manually
shifting values.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This must have been implicitly included on the builds I tested. Reported
by numerous test bots:
drivers/mtd/nand/vf610_nfc.c: In function 'vf610_nfc_resume':
drivers/mtd/nand/vf610_nfc.c:660:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This reverts commit 7827e3acad.
There are some 64-bit arithmetic issues on some architectures, so let's
wait until we get a better patch for this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).
Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.
Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.
Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.
Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.
Colibri VF50
eb write % eb read % page write % page read %
rel/opt 5175 11537 4560 11039
opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10
none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58
Colibri VF61
eb write % eb read % page write % page read %
rel/opt 5766 13096 5459 12846
opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34
none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86
rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write
The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After a bit of poking around wondering why my 32-bit user-space can't
seem to send a proper ioctl(BLKPG) to an MTD on my 64-bit kernel
(ARM64), I noticed that struct blkpg_ioctl_arg is actually pretty
unsuitable for use in the ioctl() ABI, due to its use of raw pointers,
and its lack of alignment/packing restrictions (32-bit arch'es tend to
pack the 4 fields into 4 32-bit words, whereas 64-bit arch'es would add
padding after the third int, and make this 6 32-bit words).
Anyway, this means BLKPG deserves some special compat_ioctl handling. Do
the conversion in a small shim for MTD.
block/compat_ioctl.c already has compat support for the block subsystem,
but it does so by a re-marshalling data to/from user-space (see
compat_blkpg_ioctl()). Personally, I think this approach is cleaner.
Tested only on MTD, with an ARM32 user space on an ARM64 kernel.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes timeout issues seen on large NOR flash (e.g., 16MB
w25q128fw) when using ioctl(MEMERASE) with offset=0 and length=16M. The
input parameters matter because spi_nor_erase() uses a different code
path for full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode.
Fix: use a different timeout for full-chip erase than for other
commands.
While most operations can be expected to perform relatively similarly
across a variety of NOR flash types and sizes (and therefore might as
well use a similar timeout to keep things simple), full-chip erase is
unique, because the time it typically takes to complete:
(1) is much larger than most operations and
(2) scales with the size of the flash.
Let's base our timeout on the original comments stuck here -- that a 2MB
flash requires max 40s to erase.
Small survey of a few flash datasheets I have lying around:
Chip Size (MB) Max chip erase (seconds)
---- -------- ------------------------
w25q32fw 4 50
w25q64cv 8 30
w25q64fw 8 100
w25q128fw 16 200
s25fl128s 16 ~256
s25fl256s 32 ~512
From this data, it seems plenty sufficient to say we need to wait for
40 seconds for each 2MB of flash.
After this change, it might make some sense to decrease the timeout for
everything else, as even the most extreme operations (single block
erase?) shouldn't take more than a handful of seconds. But for safety,
let's leave it as-is. It's only an error case, after all, so we don't
exactly need to optimize it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 512KiB flash with 4 KiB erase sectors.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The module pcmciamtd doesn't generate a mtd node for PRETEC 4MB SRAM
cards without the id and hash added to pcmciamtd.c
Tested on 3 different 4MB pretec sram cards.
Signed-off-by: Tom Englund <tomenglund26@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A read id operation followed by 0x00 reads the device ID while
a read id operation followed by 0x20 reads the possible ONFI identifier.
As the READID function did not propagate the second id parameter but had
a hard-coded call for 0x90 0x00, reading the ONFI identifier was not
possible and thus chips werde not detected (tested with
MT29F8G08ABABAWP)
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch trivially updates code comments to reflect the addition of the
UBI_METAONLY flag - as discussed https://lkml.org/lkml/2014/10/29/764
Cc: Richard Weinberger <richard@nod.at>
Cc: trivial@kernel.org
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
This driver uses some custom macros for printing. Let's use the standard
pr_fmt()/pr_{err,warn}().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I'm not sure why we have a PAGE_SIZE restriction on this partition
parser.
If we really wanted the restriction, I would expect it to be a
restriction for *all* parsers, so we'd move it to the MTD core
At any rate, while small partitions may not be useful (they'll often be
smaller than the eraseblock size and therefore can only be used
read-only), they still have use as a read-only partition.
This restriction is especially annoying because it aborts the entire
MTD's cmdline parsing, leaving it unpartitioned.
So, let's kill the restriction and only check for zero-sized partitions,
which I expect we don't want to allow.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s25fl016k can be found on Embedded Artists' LPC4357 Developer's Kit
where is used in quad mode by the LPC4357 SPIFI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After the conversion of pxa architecture to common clock framework, the
NAND clock can be disabled on driver exit.
In this case, it happens that if the driver used the NAND and set the
DFI arbitration bit, the next access to a static memory controller area,
such as an ethernet card, will stall the system bus, and the core will
be stalled forever.
This is especially true on pxa31x SoCs, where the NDCR was augmented
with a new bit to prevent this lockups by giving full ownership of the
DFI arbiter to the SMC, in change SCr#6.
Fix this by clearing the DFI arbritration bit in driver exit. This
effectively prevents a lockup on zylonite when removing pxa3xx-nand
module, and using ethernet afterwards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In drivers/mtd/mtd_blkdevs.c:
406 set_capacity(gd, (new->size * tr->blksize) >> 9);
The type of new->size is unsigned long and the type of tr->blksize is int,
the result of 'new->size * tr->blksize' may exceed ULONG_MAX on 32bit
machines.
I use nand chip MT29F32G08CBADBWP which is 4GB and the parameters passed
to kernel is 'mtdparts=gpmi-nand:-(user)', the whole nand chip will be
treated as a 4GB mtd partition. new->size is 0x800000 and tr->blksize is
0x200, 'new->size * tr->blksize' however is 0. This is what we do not want
to see.
Using type cast u64 to fix the multiplication overflow issue.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now pxa architecture has a dmaengine driver, remove the access to direct
dma registers in favor of the more generic dmaengine code.
This should be also applicable for mmp and orion, provided they work in
device-tree environment.
This patch also removes the previous hack which was necessary to make
the driver work in a devicetree environment.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Brian: fixup use of 'enum dma_transfer_direction']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nand_chips_cleanup() function is missing a call to list_del()
which generates a double free error.
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add two helper functions to help NAND controller drivers test whether a
specific NAND region is erased or not.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The USER_DATA register cannot be accessed using byte accessors on A13
SoCs, thus triggering a bug when using memcpy_toio on this register.
Declare an helper macros to convert an OOB buffer into a suitable
USER_DATA value and vice-versa.
This patch also fixes an error in the oob_required logic (some OOB data
are not written even if the user required it) by removing the
oob_required condition, which is perfectly valid since the core already
fill ->oob_poi with FFs when oob_required is false.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'write_enable' argument is unused and unneeded, so remove it from
the API.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Han Xu <han.xu@freescale.com>
[Brian: fixed for nxp-spifi.c]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use existing write_sr() call instead of decoding and
calling nor->write_reg separately.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_dt_init(), called from nand_scan_ident(), is already parsing the
generic MTD/NAND DT properties, and initializing the nand_chip struct
accordingly.
Rely on this initialization instead of manually parsing those properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: rename 'np' -> 'flash_node' to accomodate for prior rename patch]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use a more descriptive name for the device_node element in struct nand_chip .
This name matches the element name used for device_node property of a flash
in the spi-nor framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The problem this patch is trying to address is such, that SPI NOR flash
devices attached to a dedicated SPI NOR controller cannot read their
properties from the associated struct device_node.
A couple of facts first:
1) Each SPI NOR flash has a struct spi_nor associated with it.
2) Each SPI NOR flash has certain device properties associated
with it, for example the OF property 'm25p,fast-read' is a
good pick. These properties are used by the SPI NOR core to
select which opcodes are sent to such SPI NOR flash. These
properties are coming from spi_nor .dev->of_node .
The problem is, that for SPI NOR controllers, the struct spi_nor .dev
element points to the struct device of the SPI NOR controller, not the
SPI NOR flash. Therefore, the associated dev->of_node also is the
one of the controller and therefore the SPI NOR core code is trying to
parse the SPI NOR controller's properties, not the properties of the
SPI NOR flash.
Note: The m25p80 driver is not affected, because the controller and
the flash are the same device, so the associated device_node
of the controller and the flash are the same.
This patch adjusts the SPI NOR core such that the device_node is not
picked from spi_nor .dev directly, but from a new separate spi_nor
.flash_node element. This let's the SPI NOR controller drivers set up
a different spi_nor .flash_node element for each SPI NOR flash.
This patch also fixes the controller drivers to be compatible with
this modification and correctly set the spi_nor .flash_node element.
This patch is inspired by 5844feeaa4
mtd: nand: add common DT init code
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_scan_ident() leaves the chip deselected. So just issuing some commands
from the sunxi driver does not work. We need to select the chip before
writing the commands to the NAND device. This patch takes care of this.
Set the new timing on all dies implemented as suggested by Boris.
This was detected on the in-circuit ICnova-A20 SoM equipped with the
Micron MT29F32G08CBACAWP (4GiB) ONFI NAND device.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: fixup whitespace]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
* SPI NOR: a few new IDs / feature flags
* OMAP2 NAND: rename module so it doesn't conflict with onenand omap2.ko
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aXrv
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd
Pull more MTD updates from Brian Norris:
"There was one significant bug in my first pull request, fixed here. I
also threw in a few trivial ID additions and a small module rename.
Details:
- SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
- SPI NOR: a few new IDs / feature flags
- OMAP2 NAND: rename module so it doesn't conflict with onenand
omap2.ko"
* tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd:
mtd: spi-nor: fix NULL dereference when no match found in spi_nor_ids[]
mtd: spi-nor: s25sl064p supports both dual and quad I/O
mtd: spi-nor: allow dual/quad reads on S25FL129P
mtd: nand: omap2: Rename shippable module to omap2_nand
mtd: spi-nor: Add support for sst25wf020a
mtd: spi-nor: Add support for Micron n25q064a serial flash
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
The driver supports board files specificating the flash
device, by passing a pxa3xx_nand_flash struct (with
flash parameters) in the platform data struct.
Currently this support is not being used by any board file.
Moreover, we'd like to deprecate such usage in favor of
using the device table in nand_ids.c.
So let's remove the ad-hoc flash specification.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We don't really need the flash information from the device tree here.
Let's stick with autodetection here instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han Xu <han.xu@freescale.com>
Tested-by: Han Xu <han.xu@freescale.com>
This reflects the proper layering, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Layering suggests that the SPI NOR layer (not the hardware driver)
should be initializing the MTD layer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
This chip can be found on Hitex LPC4350 Evaluation Board.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the datasheet[1], both S25FL129P0 (256kB sectors) and
S25FL129P1 (64kB sectors) support dual read, quad read, dual i/o read
and quad i/o read.
I have verified dual read to be working for S25FL129P1 on a dual
capable spi controller. Quad as well as S25FL129P0 is untested, lacking
hardware to verify.
[1] http://www.spansion.com/Support/Datasheets/S25FL129P_00.pdf
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As both omap2 onenand and omap2 nand driver modules are
named the same i.e. "omap2.ko", only one of them gets shipped
during MODPOST if both are configured as loadable modules.
To avoid this ambiguity let's ship the omap2 nand
driver as "omap2_nand.ko"
Reported by Pierre Neyron via github
https://github.com/beagleboard/linux/issues/40
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 256KiB flash with 4 KiB erase sectors
and 64KiB overlay blocks.
This is the one available on Hardkernel's Odroid U3 shield.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
[Brian: seems like this does NOT require the usual SST_WRITE hacks]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Micron (n25q064a) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[Brian: fixup context]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
When vary_offset is set (e.g. test case 3), the offset is not always
zero so memcmpshow() will show the wrong offset in the print message.
To fix this we introduce a new function memcmpshowoffset() which takes
offset as a parameter and displays the right offset and use it in
the case where offset is non zero.
The old memcmpshow() functionality is preserved by converting it into
a macro with offset preset to 0.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With gcc 5.1 I get:
warning: switch condition has boolean value [-Wswitch-bool]
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using struct spi_device_id for storing list of flash devices comes from
early SPI NOR framework days. Thanks to the commit 70f3ce0510 ("mtd:
spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id")
we can stop using spi_device_id and just switch to our own struct.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the full description of the Toshiba TC58NVG0S3E NAND chip in the
nand_ids table so that we can later use the NAND ECC info and ONFI timing
mode in controller drivers.
Tested with asm9260_nand driver. [Brian: driver still under review]
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The SPI core currently reports the MODALIAS uevent as "spi:<modalias>"
even for SPI devices that were registered by OF.
That means the OF module alias exported by MODULE_OF_TABLE(of,...) is
currently not used and user-space has no way to autoload this module.
But it is still a good practice to add the OF module alias information
into the kernel module even when it currently is unused so once the SPI
core is changed to report a correct OF modalias uevent, module
autoloading will be working for this driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read after
an erase.
The issue is that in the interrupt handler, the status bits are cleared
after the new command is issued. There is a small temporal window where
this happens :
- the previous command has set the command done bit
- the ready for a command bit is set
- the handler submits the next command
- just then, the command completes, and the command done bit is still
set
- the handler clears the "previous" command done bit
- the handler exits
In this flow, the "command done" of the next command will never trigger
a new interrupt to finish the status command, as it was cleared for both
commands.
Fix this by clearing the status bit before submitting a new command.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
The bug is tricky : if the bootloader left a status bit set, the
unmasking of interrupts does trigger the interrupt handler before the
first command is issued, blocking the good behavior of the nand.
The same would happen if in pxa3xx_nand code flow a status bit is left,
and then a command is started.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.
In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.
Fixes: 70ed85232a ("mtd: nand: pxa3xx: Introduce multiple page I/O
support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove extra space after the "platform:" prefix and make the alias matches
driver name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
static analysis by smatch caught the following error:
drivers/mtd/maps/physmap_of.c:135 of_get_probes()
error: potential null dereference 'res'. (kzalloc returns null)
Check for failed kzalloc and return -ENOMEM in of_flash_probe if
this occurs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If mtd_device_register() fails in nettel_init(), iomap left mapped.
The patch adds failure handling for mtd_device_register().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is better to have device name prefixed the actual error message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In recent kernels we have a lot of helper functions, including
devres API, to make life of device driver developer easy.
Convert the driver using devm_kzalloc() and pcim_enable_device().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Let's use module_pci_driver() macro to reduce code base of the driver.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to user to see the core part of the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current "We only connect the NOR to this controller now." text
is not very clear, so explain it better by saying that generic SPI
is not supported by SPI_FSL_QUADSPI and only SPI NOR is.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add SPI-NOR driver for the SPI Flash Interface (SPIFI)
controller that is found on newer NXP MCU devices.
The controller supports serial SPI Flash devices with 1-, 2-
and 4-bit width in either SPI mode 0 or 3. The controller
can operate in either command or memory mode. In memory mode
the Flash is exposed as normal memory and can be directly
accessed by the CPU.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
IFC IO accressor are set at run time based
on IFC IP registers endianness.IFC node in
DTS file contains information about
endianness.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Erase function will use cmd 0x20 (SPINOR_OP_BE_4K) if kenrel enable option
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
This command is not in fsl-quadspi driver LUT. So driver continue report
fsl-quadspi 21e0000.qspi: Unsupported cmd 0x20.
This patch fix this issue.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The uboot may run the QuadSpi controler with command:
#sf probe
So we should reset the module in the probe.
This patch also clear the pending interrupts which arised by the uboot
code.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI1 cannot wake up CCM from WAIT mode on SX ARD board, add pmqos to
let PM NOT enter WAIT mode when accessing QSPI1, refer to TKT245618.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We found there is a low probability(5%) QSPI access timeout issue,
usually it happened on kernel boot stage, the first time kernel tried to
access QSPI chip. The READ_ID command was sent but not executed,
consequently the probe function failed.
The root cause is that the divider is not glitchless in i.MX6SX chip.
If qspi clock enabled then change clock frequency by call clk_set_rate,
there will be glitch at low possiblity rate and pass to qspi controller.
The controler will be hang by this glitch.
Based on the new clock flag(CLK_SET_RATE_GATE) and new framework, we
need to change the approach of seting clock rate.
1. Disable clock.
2. call clk_set_rate.
3. Enable clock again.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add i.mx6ul chip support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Support i.mx7d.
quadspi in i.mx7d increase rxfifo.
require fill at least 16byte to trigger data transfer.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
add several quirk to distinguish different version of qspi module.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI may failed to map enough memory (256MB) for AHB read in
previous implementation, especially in 3G/1G memory layout kernel.
Dynamically map memory to avoid such issue.
This implementation generally map QUADSPI_MAX_IOMAP (default 4MB) memory
for AHB read, it should be enough for common scenarios, and the side
effect (0.6% performance drop) is minor.
Previous implementation
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.16006 s, 15.5 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43149 s, 23.4 MB/s
After applied the patch
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.1743 s, 15.4 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43158 s, 23.4 MB/s
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:
// Option (a), modalias = "spi-nor"
compatible = "jedec,spi-nor";
// Option (b), modalias = "spi-nor"
compatible = "idontknowwhatimdoing,spi-nor";
But the following would not:
// Option (c), modalias = "shinynewdevice"
compatible = "myvendor,shinynewdevice", "jedec,spi-nor";
So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).
To do this, we
(1) always (for devices without specific platform data) pass the
modalias to the spi-nor library;
(2) rework the spi-nor library to not reject "bad" names, and
instead just fall back to autodetection; and
(3) add the .of_match_table to properly catch all "jedec,spi-nor".
This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Replaces the hard coded "always use EDO" policy with that prescribed
by the ONFI 3.1 specification that EDO mode should always be used if tRC
is below 30ns.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The TIMING_CFG register was previously statically set to a magic value
(extracted from Allwinner's BSP) when initializing the NAND controller.
Now that we have more details about the TIMING_CFG register layout
(extracted from the A83 user manual) we can dynamically calculate the
appropriate value for each NAND chip and set it when selecting the
chip.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QUADSPI_MCR_CLR_TXF_MASK is the correct mask for clearing the TX FIFO.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
r852_ecc_correct() reads a 32-bit register into a 16-bit variable,
ecc_reg, but this variable is later used as if it was larger. This is
reported by clang when building the kernel with many warnings:
drivers/mtd/nand/r852.c:512:11: error: shift count >= width of type
[-Werror,-Wshift-count-overflow]
ecc_reg >>= 16;
^ ~~
Fix this by making ecc_reg 32-bit, like the return type of
r852_read_reg_dword().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.
[Brian: similar work submitted by Murali Karicheri <m-karicheri2@ti.com>
and Hao Zhang <hzhang@ti.com>]
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Do not call free_device() in init_nandsim, the caller - ns_init_module -
will take care of that if something goes wrong.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If allocating ns->nand_pages_slab fails, do not try to destroy it when
cleaning up nandsim resources.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
* Minor fixes for UBI and UBIFS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xU0H
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.2-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
"Minor fixes for UBI and UBIFS"
* tag 'upstream-4.2-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Remove unnecessary `\'
UBI: Use static class and attribute groups
UBI: add a helper function for updatting on-flash layout volumes
UBI: Fastmap: Do not add vol if it already exists
UBI: Init vol->reserved_pebs by assignment
UBI: Fastmap: Rename variables to make them meaningful
UBI: Fastmap: Remove unnecessary `\'
UBI: Fastmap: Use max() to get the larger value
ubifs: fix to check error code of register_shrinker
UBI: block: Dynamically allocate minor numbers
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
Add supports for simultaneous access to multiple chips. Need to lock
the mutex before any quad spi operations and unlock the mutex after
operations complete.
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: reworked err path in fsl_qspi_prep()]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() does a dynamic memory allocation and can fail.
We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() used in get_partition_name() does a dynamic
memory allocation and can fail. We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() does a dynamic memory allocation and can fail.
We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
device_create_file() can fail, therefore we have to
handle this case and abort.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It makes more sense to return error statuses, not 1/0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
It is a Bad Idea (TM) to call mtd_device_register() or
mtd_device_parse_register() twice on the same master MTD. Among other
things, it makes partition overrides (e.g., cmdlinepart) much more
difficult.
Since commit 727dc612c4 ("mtd: part: Create the master device node
when partitioned"), we now have a config option that accomplishes the
same purpose as the double-registration done in diskonchip.c -- it
forces the master MTD to *always* be registered, while partitions may
optionally show up in addition. Eventually, we might like to make
CONFIG_MTD_PARTITIONED_MASTER into the default, but this could be
disruptive to user-space expectations of MTD numbering, so we'll take
that slowly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Alexander Shiyan <shc_work@mail.ru>
Powerpc powernv platforms allow access to certain system flash devices
through a firmwarwe interface. This change adds an mtd driver for these
flash devices.
Minor updates from Jeremy Kerr and Joel Stanley.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reviewed-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.
This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it. c files
which need access to more backing-dev details now include
backing-dev.h directly. This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.
v2: fs/fat build failure fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch cleans up the manual device_create_file() or
class_create_file() calls by replacing with static attribute groups.
It simplifies the code and also avoids the possible races between the
device/class registration and sysfs creations.
For the simplification, also make ubi_class a static instance with
initializers, too.
Amend a bit by Hujianyang.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
During fastmap attaching, check if a volume already exists when adding
the volume to volume tree. NOTE that the issue cannot happen, only if
the on-flash fastmap data is modified.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
`vol' is a newly allocated value by kzalloc. Initialize it by assignment
instead of `+='.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
s/fmpl1/fmpl
s/fmpl2/fmpl_wl
Add "WL" to the error message when wrong WL pool magic number is detected.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch makes ubiblock devices have minor numbers beginning from
0, allocated dynamically independently of the ubi device/volume
number. This property becomes useful because, on 32-bit architectures
with LFS turned off in a userspace program, device minor numbers
over 8 bits cause stat to return -EOVERFLOW. If the device number is
high (>1) due to multiple MTD partitions, such an overflow will occur.
While enabling LFS is clearly a nicer solution, it's often difficult
to turn on in practice globally as many widely distributed packages
don't work with LFS on.
Other storage systems have their own workarounds, with SCSI making
multiple device majors and MMC having a config option for the number
of partitions per device. A completely dynamic minor numbering is
simpler than these. It is unlikely that anyone is depending on a
static minor number since the major is dynamic anyway. In addition,
ubiblock is still relatively new, so now is the time to make such
changes.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit bd31b85960 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.
This fixes:
drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
spin_lock_irqsave(&nw_gpio_lock, flags);
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
^
drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
spin_unlock_irqrestore(&nw_gpio_lock, flags);
^
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
Fixes: bd31b85960 ("locking, ARM: Annotate low level hw locks as raw")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 4612c715a6 ("mtd: cfi: deinline large functions") moved some
code into the cfi_util library without creating a new dependency. So we
can get build failures like the following, when CONFIG_MTD_JEDECPROBE=y
and CONFIG_MTD_CFI_UTIL=m.
drivers/built-in.o: In function `jedec_read_id':
>> jedec_probe.c:(.text+0x187ed8): undefined reference to `cfi_build_cmd_addr'
drivers/built-in.o: In function `jedec_read_mfr':
>> jedec_probe.c:(.text+0x187f4a): undefined reference to `cfi_build_cmd_addr'
drivers/built-in.o: In function `jedec_reset':
>> jedec_probe.c:(.text+0x187fe0): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x188004): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18802b): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18804e): undefined reference to `cfi_send_gen_cmd'
drivers/built-in.o: In function `jedec_probe_chip':
>> jedec_probe.c:(.text+0x188130): undefined reference to `cfi_build_cmd_addr'
>> jedec_probe.c:(.text+0x18814d): undefined reference to `cfi_build_cmd_addr'
>> jedec_probe.c:(.text+0x1881dc): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x188203): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18822d): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x1884c0): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x1884e7): undefined reference to `cfi_send_gen_cmd'
drivers/built-in.o:jedec_probe.c:(.text+0x188511): more undefined references to `cfi_send_gen_cmd' follow
drivers/built-in.o: In function `jedec_probe_chip':
>> jedec_probe.c:(.text+0x188618): undefined reference to `cfi_build_cmd'
So let's express the dependency properly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In do_otp_write we must initialize the variable datum before calling
map_word_load_partial. Otherwise the upper bits of datum may be undefined,
which later causes problems in chip_good called by do_write_oneword.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's harmless to add 'ofpart' (the only different parser supported in
default mtdpart.c) to plat_nand. That let's us kill off one more custom
partition prober listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
