This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
following ports:
- host 0 and 1 of CPM
- host 0 of CPS
These PHY are enabled by lanes coming from regulators based on two
I2C expanders.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add I2C expander and USB host PHY (host 0 and host 1) to enable
USB VBUS on USB ports of type A on Armada-7040-DB.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The ESPRESSObin board exposes one of the SDHCI interfaces
via J1 uSD slot. This patch enables it.
Tested-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Zbigniew Bodek <zbodek@gmail.com>
[gregory.clement@free-electrons.com: removed "no-1-8-v"]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.
[gregory.clement@free-electrons.com: use commit log from Thomas]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Espressobin SBC has a USB2 interface available on J8. Let's
enable it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a PMUv3, just like most ARMv8 cores.
Advertise the PMUv3 presence in the device tree, and wire its
interrupt. This allows the perf subsystem to work correctly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a GIC CPU interface that gets enabled when coupled with a GICv3
interrupt controller, such as the GIC-500 on the this SoC.
Advertise the MMIO ranges provided by the CPUs, which enables
(among other things) GICv2 guests to run under a hypervisor such
as KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007fed ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The crypto engines found on the cp110 master and slave are dma coherent.
This patch adds the relevant property to their dt nodes.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 973020fd94 ("arm64: marvell: dts: add crypto engine description for 7k/8k")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When the conversion of the Marvell CP110 Device Tree description from
using GIC interrupts to using ICU interrupts was done, the RTC on the
slave CP110 was left unchanged. This commit fixes that, so that all
devices on the CP properly get their interrupt through the ICU.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWVpGxCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SGMAKCP9mGjMWqD
Z9uCT8swDJ8LCi/o+wCfV4Cs0eWzqkJUDMaycdJrlMjB174=
=TavE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "late dt64 for 4.13" from Gregory CLEMENT:
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
* tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:
- dma-masks are a Linux specific concept, not a general
hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
the SoC cannot address that much memory anyway, so simply
asking for a 64-bit mask (as supported by the device) should
succeed anyway.
The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWTAszCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71bcsAJ4kcIDc5FwI
e9qfRomziu3A+S6K0QCfX3Ii7XGH1fANfeTCAnyZGXmYFZI=
=wjTT
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu:
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.
The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.
On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.
For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable pinctrl support for CP and AP on the Armada 7K/8K SoCs.
The CP master being different between Armada 7k and Armada 8k. This
commit introduces the intermediates files armada-70x0.dtsi and
armada-80x0.dtsi.
These new files will provide different compatible strings depending of
the SoC family. They will also be the location for the pinmux
configuration at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
New bindings are used for the system controller on the ap806, which
means all clock properties must be converted. Use the new bindings in
the xor nodes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio node for the 8040-mcbin.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the xMDIO bus for the Marvell Armada 7k and
Marvell Armada 8k; for both CP110 slave and master. This bus is found
on Marvell Ethernet controllers and provides an interface with the
xMDIO bus.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cryptographic engine found on the cp110 slave is disabled by default
because of some known limitations. Add a comment to explain why it is
disabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cryptographic engine on the master cp110 is now enabled by default
at the SoC level. Remove its dts nodes that were only enabling it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the cryptographic engine at the SoC level on the master cp110.
This engine is always present and do not depends on any pinmux
configuration.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, the SD cards are usable at higher speed
protocols such as SDR104.
This patch was tested with an SD HC card compatible with UHS-I.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 37xx SoCs has 2 SDHCI interfaces. This patch adds the second
one.
Moreover, the Armada 37xx DB v2 board populates the 2 SDHCI interfaces.
The second interface is using pluggable module that can either
have an SD connector or eMMC on it.
This patch adds support for SD module in the device DT.
[ gregory.clement@free-electrons.com:
- Add more detail in commit log
- Sort the dt node in address order
- Document the SD slot in the dts ]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When several groups of register address and size are used with reg, then
surround each one by angle bracket.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The initial device tree file was for the board V1.4. Now the V2.0 board
is also available. The same dtb will work for both, but the CON number
have changed, so update the comment in the dts to reflect this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Sort the reference nodes in alphabetical order to ease the merge of
future nodes.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Disable the mdio nodes by default in the cp110 slave and master dtsi as
they're not wired on every board.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Explicitly enable the MDIO nodes in the Marvell Armada 7k DB and Marvell
Armada 8k DB. This is needed as the MDIO nodes will be disabled in the
CP 110 slave and master dtsi by a following up patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The EIP197 cryptographic engine supports 64 bits address width but is
limited to 40 bits on 7k/8k. Add a dma-mask property in the
cryptographic engine nodes to reflect this.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
