1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.
Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far there were two monitor frame formats:
1) 802.11 frames (with frame (sub)type & all addresses)
2) 802.11 frames with the radiotap header
Testing the latest FullMAC firmwares for 4366b1/4366c0 resulted in
discovering a new format being used. It seems (almost?) identical to the
one known from ucode used in SoftMAC devices which is most likely the
same codebase anyway.
While new firmwares will /announce/ radiotap header support using the
"rtap" fw capability string it seems no string was added for the new
ucode header format.
All above means that:
1) We need new format support when dealing with a received frame
2) A new feature bit & mapping quirks have to be added manually
As for now only an empty radiotap is being created. Adding support for
extracting some info (band, channel, signal, etc.) is planned for the
future.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spelling mistakes in brcmfmac: "lenght" -> "length".
The typos are also in the special comment blocks which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new macro uses wiphy_err() which:
1) Should be the best choice with wiphy already created
2) Uses dev_err() which allows identifying error-affected device
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables dev_err() usage (instead of pr_err()) in the __brcmf_err().
It makes error messages more meaningful and is important for debugging
errors/bugs on systems with multiple brcmfmac supported devices.
All bus files should follow & get updated similarly (soon).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far __brcmf_err() was using pr_err() which didn't allow identifying
device that was affected by an error. It's crucial for systems with more
than 1 device supported by brcmfmac (a common case for home routers).
This change allows passing struct brcmf_bus to the __brcmf_err(). That
struct has been agreed to be the most common one. It allows accessing
struct device easily & using dev_err() printing helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
I also removed one header search path in:
drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile
I was able to compile without it.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The linux-firmware brcmfmac firmware files contain an embedded table with
per country allowed channels and strength info.
For recent hardware these versions of the firmware are specially build for
linux-firmware, the firmware files directly available from Cypress rely on
a separate clm_blob file for this info.
For some unknown reason Cypress refuses to provide the standard firmware
files + clm_blob files it uses elsewhere for inclusion into linux-firmware,
instead relying on these special builds with the clm_blob info embedded.
This means that the linux-firmware firmware versions often lag behind,
but I digress.
The brcmfmac driver does support the separate clm_blob file and always
tries to load this. Currently we use request_firmware for this. This means
that on any standard install, using the standard combo of linux-kernel +
linux-firmware, we will get a warning:
"Direct firmware load for ... failed with error -2"
On top of this, brcmfmac itself prints: "no clm_blob available (err=-2),
device may have limited channels available".
This commit switches to firmware_request_nowarn, fixing almost any brcmfmac
device logging the warning (it leaves the brcmfmac info message in place).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a system warning message, warn_slowpath-fmt, during suspend
while using supplicant join AP and enable wowl feature by IW command.
It's caused by brcmf_pno_remove_request path can't find the reqid.
This fix will not go to remove pno request function if there is no
pno scan.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Lo-Hsiang Lo <double.lo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_register() may fail, so let's check its status and issue an error
message if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Point of View TAB-P1006W-232 tablet contains quite generic names in
the sys_vendor and product_name DMI strings, without this patch brcmfmac
will try to load: brcmfmac43340-sdio.Insyde-BayTrail.txt as nvram file
which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file
name is used on the PoV TAB-P1006W-232 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1202:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4625:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4834:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3085:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4215:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since commit 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
the Raspberry Pi 3 A+ (BCM43455) isn't able to operate in AP mode with
hostapd (device_ap_sme=1 use_monitor=0):
brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -52
So add the missing mgmt_stypes for AP mode to fix this.
Fixes: 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/phy_n.c: In function 'b43_nphy_op_recalc_txpower':
drivers/net/wireless/broadcom/b43/phy_n.c:5898:7: warning:
variable 'tx_pwr_state' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/b43/phy_n.c:6047:20: warning:
variable 'tmp2' set but not used [-Wunused-but-set-variable]
'tx_pwr_state' never used since introduction in commit
8615eb2870 ("b43: N-PHY: support setting custom TX power")
'tmp2' not used any more since commit c002831a07 ("b43: N-PHY: use helper
for checking IPA")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_NO_AUTO_INLINE is set, we get a false-postive warning
for the brcmf_fw_request_nvram_done() function, after gcc figures
out that brcmf_fw_nvram_from_efi() might not set the 'data_len'
variable, but fails to notice that it always returns NULL:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c: In function 'brcmf_fw_request_nvram_done':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:560:11: error: 'data_len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Mark it 'inline' to force gcc to understand this.
Fixes: ce2e6db554 ("brcmfmac: Add support for getting nvram contents from EFI variables")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.
Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.
Command decode for below chips are disabled in this commit:
- 4339
- 4345
- 4354
- 4373
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use chipcommon sr_control0 register to check 4373 sr support.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
- Allow GCI to be added to core list even when it doesn't have a wrapper.
- Allow 8K address space size.
- Don't overwrite the address value when an additional size descriptor
is in place.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware inform the driver about tx status by normal tx status signal
or compressed tx status signal. This patch adds support to handle the
compressed tx status signal.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The credit numbers are static and tunable per chip in firmware side.
However the credit number may be changed that is based on packet pool
length and will send BRCMF_E_FIFO_CREDIT_MAP event to notify host driver
updates the credit numbers during interface up.
The purpose of this patch is making host driver has ability of updating
the credit numbers when receiving the BRCMF_E_FIFO_CREDIT_MAP event.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.
In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
classic uboot booting, the devicetree data is always there, so using it
makes sure we ask for the same nvram file independent of how we booted.
This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.
Fixes: bd1e82bb42 ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newest firmwares provide STA info using v7 of the struct. As v7
isn't backward compatible, a union is needed.
Even though brcmfmac does not use any of the new info it's important to
provide the proper struct buffer. Without this change new firmwares will
fallback to the very limited v3 instead of something in between such as
v4.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kernel library has a common cordic algorithm which is identical
to internally implemented one, so use it and drop the duplicate
implementation.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a9f ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.
This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.
Fixes: 9865045403 ("b43: make cordic common (LP-PHY and N-PHY need it)")
Reported-by: Priit Laes <plaes@plaes.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> # 2.6.34
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current driver includes macro that is available from general cordic
library. Use that and drop unused duplicate and unneeded internal
definitions.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can report IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ so it's
important to provide valid & complete info about supported bands for
each channel. By default no support for 160 MHz should be assumed unless
firmware reports it for a given channel later.
This fixes info passed to the userspace. Without that change userspace
could try to use invalid channel and fail to start an interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of direct SKB list pointer accesses.
The loops in this function had to be rewritten to accommodate this
more easily.
The first loop iterates now over the target list in the outer loop,
and triggers an mmc data operation when the per-operation limits are
hit.
Then after the loops, if we have any residue, we trigger the last
and final operation.
For the page aligned workaround, where we have to copy the read data
back into the original list of SKBs, we use a two-tiered loop. The
outer loop stays the same and iterates over pktlist, and then we have
an inner loop which uses skb_peek_next(). The break logic has been
simplified because we know that the aggregate length of the SKBs in
the source and destination lists are the same.
This change also ends up fixing a bug, having to do with the
maintainance of the seg_sz variable and how it drove the outermost
loop. It begins as:
seg_sz = target_list->qlen;
ie. the number of packets in the target_list queue. The loop
structure was then:
while (seq_sz) {
...
while (not at end of target_list) {
...
sg_cnt++
...
}
...
seg_sz -= sg_cnt;
The assumption built into that last statement is that sg_cnt counts
how many packets from target_list have been fully processed by the
inner loop. But this not true.
If we hit one of the limits, such as the max segment size or the max
request size, we will break and copy a partial packet then contine
back up to the top of the outermost loop.
With the new loops we don't have this problem as we don't guard the
loop exit with a packet count, but instead use the progression of the
pkt_next SKB through the list to the end. The general structure is:
sg_cnt = 0;
skb_queue_walk(target_list, pkt_next) {
pkt_offset = 0;
...
sg_cnt++;
...
while (pkt_offset < pkt_next->len) {
pkt_offset += sg_data_size;
if (queued up max per request)
mmc_submit_one();
}
}
if (sg_cnt)
mmc_submit_one();
The variables that maintain where we are in the MMC command state such
as req_sz, sg_cnt, and sgl are reset when we emit one of these full
sized requests.
Signed-off-by: David S. Miller <davem@davemloft.net>
On one of my devices I got WARNINGs when brcmfmac tried to decode
chanspec. I couldn't tell if it was some unsupported format or just a
malformed value passed by a firmware.
Print chanspec value so it's possible to debug a possible problem.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This message greatly spams the log under heavy Tx of frames with BK access
class which is especially true when operating as AP. It is also not informative
as the "agg'ablity" of TIDs are set once and never change.
Fix this by logging only in debug mode.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in brcmf_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases the EFI-var stored nvram contains "ccode=ALL" or "ccode=XV"
to specify "worldwide" compatible settings, but these 2 ccode-s do not work
properly.
I've tested the different known "worldwide" ccode-s used in various nvram
sources with the latest firmwares from linux-firmware for various brcmfmac
models, here is a simplified (*) table with what each setting results in:
ALL: 12-14 disab, U-NII-1, U-NII-2 no-IR/radar, U-NII-3
XV: 12-14 no-IR, disables all 5G channels
XY: 12-13 enab, 14 disab, U-NII-1 enab, U-NII-2 no-IR/radar, U-NII-3 disab
X2: 12-13 no-IR, 14 dis, U-NII-1 no-IR, U-NII-2 no-IR/radar, U-NII-3 no-IR
Where 12,13,14 are 2.4G channels 12-14 and U-NII-1/2/3 are the 3 different
5G channel groups. no-IR is no-Initiate-Radiation, we will never send on
these channels without first having received valid wifi traffic there.
This immediately shows that both ALL and XV are not as worldwide as we want
them to be. ALL causes channels 12 and 13 to not be available and XV causes
all 5GHz channels to not be available. Also ALL unconditionally enables the
U-NII-1 and U-NII-3 5G groups, while we really should be using no-IR for
these.
This commit replace XV and ALL with X2, which allows usage of chan 12-13
and 5G channels, but only after receiving valid wifi traffic there first.
Note that this configure the firmware's channel limits, the kernels own
regulatory restrictions based on e.g. regulatory info received from the
access-point, will be applied on top of this.
This fixes channels 12+13 not working on the Asus T200TA and the Lenovo
Mixx 2 8 and 5G channels not working on the Asus T100HA.
This has been tested on the following models: Acer Iconia Tab8 w1-810,
Acer One 10, Asus T100CHI, Asus T100HA, Asus T100TA, Asus T200TA and a
Lenovo Mixx 2 8.
*) There are some exceptions to this table:
1) On really old firmware e.g. linux-firmware's 2011 brcmfmac4330-sdio.bin
ALL really means all, unconditionally enabling everything
2) The exact meaning might be influenced by setting the regrev nvram var.
Specifically using ccode=XV + regrev=1 on brcmfmac43241b4 leads to:
12-14 no-ir, U-NII-1 no-ir, U-NII-2 no-ir/radar, U-NII-3 no-ir
But only on the brcmfmac43241b4 and not on e.g. the brcmfmac43340
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various X86 laptops with a SDIO attached brcmfmac wifi chip, store the
nvram contents in a special EFI variable. This commit adds support for
getting nvram directly from this EFI variable, without the user needing
to manually copy it.
This makes Wifi / Bluetooth work out of the box on these devices instead of
requiring manual setup.
This has been tested on the following models: Acer Iconia Tab8 w1-810,
Acer One 10, Asus T100CHI, Asus T100HA, Asus T100TA, Asus T200TA and a
Lenovo Mixx 2 8.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "cur" variable is now only used for a debug print and we already
print the same info from brcmf_fw_complete_request(), so the debug print
does not provide any extra info and we can remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For x86 based machines, set the board_type used for nvram file selection
based on the DMI sys-vendor and product-name strings.
Since on some models these strings are too generic, this commit also adds
a quirk table overriding the strings for models listed in that table.
The board_type setting is used to load the board-specific nvram file with
a board-specific name so that we can ship files for each supported board
in linux-firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For of/devicetree using machines, set the board_type used for nvram file
selection to the first string listed in the top-level's node compatible
string, aka the machine-compatible as used by of_machine_is_compatible().
The board_type setting is used to load the board-specific nvram file with
a board-specific name so that we can ship files for each supported board
in linux-firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nvram files which some brcmfmac chips need are board-specific. To be
able to distribute these as part of linux-firmware, so that devices with
such a wifi chip will work OOTB, multiple (one per board) versions must
co-exist under /lib/firmware.
This commit adds support for callers of the brcmfmac/firmware.c code to
pass in a board_type parameter through the request structure.
If that parameter is set then the code will first try to load
chipmodel.board_type.txt before falling back to the old chipmodel.txt name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this commit brcmf_fw_request_done would call
brcmf_fw_request_next_item to load the next item, which on an error would
call brcmf_fw_request_done, which if the error is recoverable (*) will
then continue calling brcmf_fw_request_next_item for the next item again
which on an error will call brcmf_fw_request_done again...
This does not blow up because we only have a limited number of items so
we never recurse too deep. But the recursion is still quite ugly and
frankly is giving me a headache, so lets fix this.
This commit fixes this by removing brcmf_fw_request_next_item and by
making brcmf_fw_get_firmwares and brcmf_fw_request_done directly call
firmware_request_nowait resp. firmware_request themselves.
*) brcmf_fw_request_nvram_done fallback path succeeds or
BRCMF_FW_REQF_OPTIONAL is set
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_fw_request_next_item and brcmf_fw_request_done both have identical
code to complete the fw-request depending on the item-type.
This commit adds a new brcmf_fw_complete_request helper removing this code
duplication.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8 ("brcmfmac: fix for proper support of 160MHz bandwidth")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Beacons are not updated to reflect TIM changes. This is not compliant with
power-saving client stations as the beacons do not have valid TIM and can
cause the network to stall at random occasions and to have highly variable
latencies.
Fix it by updating beacon templates on mac80211 set_tim callback.
Addresses an issue described in:
https://marc.info/?i=20180911163534.21312d08%20()%20manjaro
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbua+lAAoJEG4XJFUm622bc74H/3CU3nKceottcybfmdNcxbTj
OHQ6ulu2OJvIrTnKOIe9WWcgoGeoEEKUcEvrV2SjopYUvFR+XPdC0TPKCxmzi020
QQyemogR+EyMx4nDqYkMysACQjTgzym8vKYrYZ5JAf0S12nRkeu4Qhvod6a9bHkO
HJWJekhm2+wIXOb02LoLhsdijhUUlYPcROZCAXlsYf7mpRIgf7PJQURI+yjfiGBW
Z8cGOH7QHU/68b5ExQAgD3OVpI7cTQ3JlE/IM1nM7UozDPRm7ZipW+Q5XJCYwjfU
Yexh1wo8CUSoK2FW5mwJJUaDUfWR5PQMDBjmGXuauFrfIrTIltJpWliEAIFV++c=
=gsaN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
variable 'wl' set but not used [-Wunused-but-set-variable]
After commit 644aa4d620 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 66cffd6daa ("b43: fix transmit failure when VT is switched"),
a condition is noted where the network controller needs to be reset. Note
that this situation happens when running the open-source firmware
(http://netweb.ing.unibs.it/~openfwwf/), plus a number of other special
conditions.
for a different card model, it is reported that this change breaks
operation running the proprietary firmware
(https://marc.info/?l=linux-wireless&m=153504546924558&w=2). Rather
than reverting the previous patch, the code is tweaked to avoid the
reset unless the open-source firmware is being used.
Fixes: 66cffd6daa ("b43: fix transmit failure when VT is switched")
Cc: Stable <stable@vger.kernel.org> # 4.18+
Cc: Taketo Kabe <kabe@sra-tohoku.co.jp>
Reported-and-tested-by: D. Prabhu <d.praabhu@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of direct SKB list pointer accesses.
In these situations, we absolutely know that the SKB queue in question
is non-empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both WARN_ON() and WARN_ON_ONCE() already contain unlikely().
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Linux Wireless Mailing List <linux-wireless@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
strnchr takes arguments in the order of its name: string, max bytes to
read, character to search for. Here we're passing '\n' aka 10 as the
buffer size, and searching for sizeof(buf) aka BRCMF_DCMD_SMLEN aka
256 (aka '\0', since it's implicitly converted to char) within those 10
bytes.
Just interchanging the last two arguments would still leave a bug,
because if we've been successful once, there are not sizeof(buf)
characters left after the new value of p.
Since clmver is immediately afterwards passed as a %s argument, I assume
that it is actually a properly nul-terminated string. For that case, we
have strreplace().
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add 4-way handshake offload detection for FT with EAP authentication.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WLAN_AKM_SUITE_FT_8021X and WLAN_AKM_SUITE_FT_PSK in
brcmf_set_key_mgmt() for FT support.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW89342 is a 2x2 MIMO, 802.11a/b/g/n/ac for WLAN. It is a member of
4355/4359 family.
Signed-off-by: Jia-Shyr Chuang <saint.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the unnecessary parentheses to fix the clang warning of
extraneous parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel BUG happens when wowl is enabled from firmware. In
brcmf_wiphy_wowl_params(), cfg is a NULL pointer because it is
drvr->config returned from wiphy_to_cfg(), and drvr->config is not set
yet. To fix it, set drvr->config before brcmf_setup_wiphy() which
calls brcmf_wiphy_wowl_params().
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NVRAM is designed to work with Broadcom's SDK Linux kernel which fakes
PCI domain 0 for all internal MMIO devices. Since official Linux kernel
uses platform devices for that purpose there is a mismatch in numbering
PCI domains.
There used to be a fix for that problem but it was accidentally dropped
during the last firmware loading rework. That resulted in brcmfmac not
being able to extract device specific NVRAM content and all kind of
calibration problems.
Reported-by: Aditya Xavier <adityaxavier@gmail.com>
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
That struct is used when querying firmware for the STA. It seem is has
been changing during the time. Luckily its format seems to be backward
compatible starting with v2 (the only breakage was v1 -> v2).
The version that was supported by brcmfmac so far was v4. It was what
43602a1 and 4366b1 firmwares (7.35.177.56 and 10.10.69.3309 accordingly)
were using. It also seems to be used by early 4366c0 firmwares
(10.10.69.6908 and 10.10.69.69017).
The problem appears when switching to the 10.10.122.20 firmware. It uses
v5 and instead of falling back to v4 when submitted buffer isn't big
enough it fallbacks to the v3.
To receive all v4 specific info with the newest firmware we have to
submit a struct (buffer) that matches v5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
That struct is passed by a firmware when querying for STA info. Flags
are used to indicate what info could be obtained.
These new defines may allow passing more info to the cfg80211 in the
future. They had been obtained from Broadcom's SDK file wlioctl_defs.h
used by DD-WRT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New Broadcom firmwares mark monitor mode packets using a newly defined
bit in the flags field. Use it to filter them out and pass to the
monitor interface. These defines were found in bcmmsgbuf.h from SDK.
As not every firmware generates radiotap header this commit introduces
BRCMF_FEAT_MONITOR_FMT_RADIOTAP flag. It has to be has based on firmware
capabilities. If not present brcmf_netif_mon_rx() will assume packet is
a raw 802.11 frame and will prepend it with an empty radiotap header.
This new code is limited to the msgbuf protocol at this point. Adding
support for SDIO/USB devices will require some extra work (possibly a
new firmware release).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on used build-time options some firmwares may already include
radiotap header in passed monitor frames. Add a new feature flag to
store info about it. It's needed for proper handling of received frames
before passing them up.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many/most of firmwares support creating monitor interface but only the
most recent ones explicitly /announce/ it using a "monitor" entry in the
list of capabilities.
Check for that entry and store internally info about monitor mode
support using a new feature flag. Once we sort out all details of
handling monitor interface it will be used when reporting available
interfaces to the cfg80211.
Later some fallback detecion method may be added for older firmwares.
For now just stick to the "monitor" capability which should be 100%
reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO1LKAAoJEG4XJFUm622bPEgH/jJ552p5KdOFkwtKWQ9sybKP
53yCEJw0sjaKVaXdPbOLZQP4ioJ0xYiOxKN1LBmBg2AVFKvnSp5LRWwmpzqdpOoE
oYo09wcSE5Q7AFHaWDmV5/6ze/S1Aem9B5iNdS/hScuXqsnqct17RVO1zVWpHnU5
W8+qVFrBcbqrvuTDdGo5GBaUQBeRHpIpGjABBk7D6qXVwOtzr2ibKGRHRITu3yYo
vA+IF+S+IwWEITt4AxaN728sk6Q3S9r5kBmRlyzlfeSmT8S/zS8Hid5P2eQz6Dv4
Ib22ZvBVFyKQd4qeXYG1lWxbTQrNZIY3JUDGkcdhkhdb3TKYL37x3mWP2LoTpK4=
=0sGc
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function wlc_phy_workarounds_nphy_rev1 is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'wlc_phy_workarounds_nphy_rev1' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the clang warning of extraneous parentheses, with the
following coccinelle script.
@@
identifier i;
expression e;
statement s;
@@
if (
-(i == e)
+i == e
)
s
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to dump dongle memory for debug upon receiving firmware halt
message through dongle to host mail box interrupt.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe dongle firmware signals a halt/trap through mailbox interrupt.
Trigger a memory dump upon receiving such signal could help to provide
useful information for issue debug.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In patch "brcmfmac: add support for sysfs initiated coredump", a new
scenario of brcmf_debug_create_memdump was added in which the user of
the function might not necessarily provide prefix data. Hence the
function should not assume the data is always valid and should perform a
check before copying.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver already supports device coredump initiated by firmware
event. Since commit 3c47d19ff4 ("drivers: base: add coredump driver
ops") it is also possible to initiate it from user-space through
sysfs. This patch adds support for SDIO and PCIe devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The only user of ALLFFMAC is the flowring module so no need to
expose it in a header file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows reading all capabilities as reported by a firmware. They are
printed using native (raw) names, just like developers like it the most.
It's how firmware reports support for various features, e.g. supported
modes, supported standards, power saving details, max BSS-es.
Access to all that info is useful for trying new firmwares, comparing
them and debugging features AKA bugs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes a sparse warning "Using plain integer as NULL pointer"
about cfg80211_inform_bss structure initialization.
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup:
Using BCM4306 rev.03 chip based CardBus wireless card.
IRQ is shared with yenta (cardbus bridge) and i915 (display) driver.
For firmware, installed latest but dated openfwwf 5.2
(http://netweb.ing.unibs.it/~openfwwf/)
How-to-reproduce:
Do "ssh <NetBSD-remotehost>", then "ls -lR /" to generate traffic, then
repeatedly switch VTs by Alt-F1<>Alt-F2.
Eventually (within a minute) the card stops working.
You can receive traffic but no transmission.
For unknown reason it doesn't occur when just generating traffic by
"ssh <remotehost> ls -lR /".
With CONFIG_B43_DEBUG=y kernel config, when it stops,
the debug message shows
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 148, but got 180
The slot offset I observed so far was always 32.
When err_out2 is not set to make error messages successive,
the debug output will be like this:
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 148
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 150
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 120
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 152
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 122
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 154
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 124
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 156
kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 126
The TX ring alternates between 2 sequences; the ring seems
to be completely confused. Controller restart is needed.
Workaround(1):
This problem doesn't occur when using propriatory firmware
you will extract by b43-fwcutter, so it may be a bug in
openfwwf firmware, as the comment in the b43_dma_handle_txstatus() suggests.
I wasn't able to find a bug in the terse openfwwf code though.
Workaround(2):
Using "pio=1" option to not use DMA makes this problem to
not occur.
Description of the patch:
This patch will forcibly reset the controller to make it
work again. Very kludgy and doesn't look right, but
the traffic will continue to flow.
Signed-off-by: Taketo Kabe <kabe@sra-tohoku.co.jp>
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac is a FullMAC driver and it implements/uses cfg80211 interface
for stations management. At the same time it doesn't receive or pass up
management frames.
This flag indicates that authenticator doesn't have to subscribe to or
handle management frames. Some authenticators (e.g. hostapd) were
working with brcmfmac thanks to some extra assumptions. This commit
clears up the situation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the addition of the TXQ stats to cfg80211, the station_info struct
has grown to be quite large, which results in warnings when allocated on
the stack. Fix the affected places to do dynamic allocations instead.
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Revision 7 of PCIe dongle interface increases the item size of tx and rx
complete rings to accommodate extra payload for new feature. This patch
simply bump up the size of these two rings without adding the support
for utilizing the new space. This makes brcmfmac compatible with rev7
firmware.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A hostready signal is introduced to inform firmware through mailbox
doorbell1 when common ring initialized or D3 exited.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The information in the firmware mapping does not need to be modified
so it can be static const.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum nl80211_band used to retrieve wiphy->bands is the same as
wiphy->bands->band which is checked by wiphy_register(). So it can be used
directly as parameter of ieee80211_channel_to_frequency().
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Provides a timestamp in bss information so user space can see when the
bss info was updated. Since tsf is not available from the dongle events
boottime is reported instead.
Reported-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mac address for p2pdev must be different from the primary interface
due to firmware requirement. Add an explicit check for this requirement
if user-space provides a mac address.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dma_tx_fragment() is never called in atomic context.
dma_tx_fragment() is only called by b43legacy_dma_tx(), which is
only called by b43legacy_tx_work().
b43legacy_tx_work() is only set a parameter of INIT_WORK() in
b43legacy_wireless_init().
Despite never getting called from atomic context,
dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:
Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
between commit:
77e30e10ee ("iwlwifi: mvm: query regdb for wmm rule if needed")
from the wireless-drivers tree and commits:
9c4f7d5127 ("iwlwifi: move all NVM parsing code to the common files")
4c625c564b ("iwlwifi: get rid of fw/nvm.c")
from the wireless-drivers-next tree.
Remove and refactor some code in order to avoid having identical code
for different branches.
Notice that this piece of code hasn't been modified since 2011.
Addresses-Coverity-ID: 1226756 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4366E is a wireless chipset with a BCM43664 ChipCommon. It's
supported by the same firmware as 4366c0.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
[arend: rebase patch and remove unnecessary definition]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When nvram loading fails a double free occurred. Fix this and reorg the
code a little.
Fixes: d09ae51a4b ("brcmfmac: pass struct in brcmf_fw_get_firmwares()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcms_ucode_init_buf() duplicates the ucode chunks via kmemdup()
with GFP_ATOMIC as a precondition of wl->lock acquired. This caused
allocation failures sometimes as reported in the bugzilla below.
When looking at the the real usage, one can find that it's called
solely from brcms_request_fw(), and it's obviously outside the lock.
Hence we can use GFP_KERNEL there safely for avoiding such allocation
errors.
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=1085174
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field did not have kerneldoc description so adding it now.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function was pretty minimal and now it is called only from one
place so just get rid of it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function is no longer used so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This changes the bus layer api by having the caller provide an
extension. With this the callback can use brcmf_fw_alloc_request()
to get the needed firmware name.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_fw_alloc_request() takes a list of required files
and allocated the struct brcmf_fw_request instance accordingly. The
request can be modified by the caller before being passed to the
brcmf_fw_request_firmwares() function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the function brcmf_fw_get_firmwares() a bit more easy to extend
using a structure to pass the request parameters.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of defining individual filenames for firmware and nvram
use a basename and derive the names from that.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver used to create a brcmfmac dir entry at the top level
debugfs mount point. This moves the debugfs entries into the
wiphy debugfs dir entry.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework the driver so the wiphy instance holds the main driver information
in its private buffer. Previously it held struct brcmf_cfg80211_info
instance so a bit of reorg was needed. This was done so that the wiphy
name or its parent device can be shown in debug output.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When logging the chip id/revision information make use of
brcmf_chip_name() so it is always the same.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip id can either be four or five digits. For the chip name either
the hexadecimal value needs to be taken (four digits) or the decimal
value (five digits). The function brcmf_chip_name() does this conversion
so use it to store the name in driver revision info.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of a linux error brcmf_fil_cmd_data() blurts an error message
in which the error code is translated to an error string. However, it
maps it to a firmware error string which should not happen. Simply
print only the numeric error code and be done with it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.
Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.
This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups
To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
disassociation perfromed by a firmware (possible local DoS attack).
It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.
This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The feature module needs to evaluate the actual firmware error return
upon a control command. This adds a flag to struct brcmf_if that the
caller can set. This flag is checked to determine the error code that
needs to be returned.
Fixes: b69c1df472 ("brcmfmac: separate firmware errors from i/o errors")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bit pattern IEEE80211_CHAN_NO_IR is being bit-wise or'd twice;
remove the redundant 2nd IEEE80211_CHAN_NO_IR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
nl80211 already allows specifying 48 bytes, but brcmfmac
only supports 32. Reject keys that are too long.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_firmware_callback() two pointer variables were used
pointing to the same construct. Get rid of sdiodev variable.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reducing the number of trace level messages in sdio code giving
them sdio log level instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No longer needed to call this in bus layer so make it static and call
it in the last phase of brcmf_attach() instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function in preparation of subsequent patch.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By calling brcmf_usb_up() during brcmf_bus_preinit() it does not need
to be called in brcmf_usb_bus_setup().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now we can move brcmf_attach() until after the firmware has been downloaded
to the device. Make the call just before brcmf_bus_started().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allocate the control rx buffer needed for firmware control interface
during brcmf_sdio_bus_preinit(). This relies on common layer setting
struct brcmf_bus::maxctl during brcmf_attach(). By moving the allocation
we can move brcmf_attach() in subsequent change.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the brcmf_bus_preinit() call allows the bus code to do some
required initialization before handling firmware control messages.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using the firmware api it can fail simply because firmware does
not like the request or it fails due to issues in the host interface.
Currently, there is only a single error code which is confusing. So
adding a parameter to pass the firmware error separately and in case
of a firmware error always return -EBADE to user-space.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The protocol layer api defines callbacks for dongle commands.
Although not really well documented these should only return an
error code in case of an error, or 0 upon success. In the bcdc
protocol it can return value above 0 and we carry a fix in the
caller of the protocol layer api. This patch makes it adhere to
the intent of the api as described above.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy chips without CLM blob files, kernel with user helper function
returns -EAGAIN when we request_firmware(), and then driver got failed
when bringing up legacy chips. We expect the CLM blob file for legacy chip
is not existence in firmware path, but the -ENOENT error is transferred to
-EAGAIN in firmware_class.c with user helper.
Because of that, we continue with CLM data currently present in firmware
if getting error from doing request_firmware().
Cc: stable@vger.kernel.org # v4.15.y
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
b43_radio_2057_init_post is not called in an interrupt handler
nor holding a spinlock.
The function mdelay in it can be replaced with usleep_range,
to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename functions to brcmf_sdio_skbuff_{read,write}() as we pass an
skbuff to this function.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_buscore_read() there is some special handling upon
register access to chipid register of the chipcommon core. Add
comment explaining why it is done here.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace the array of functions with a pair of pointers to the
relevant functions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add 43455 into the save-restore(SR) capable chip list, so
the SR engine will be enabled with 43455 FW which built-in the -sr
function.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make it more obvious that this code acually enables interrupts, and
provide nice definitions for the bits in the register.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for removing the function array, remove all code that
refers to function by index and replace with pointers to the function
itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: replace BUG() with WARN() macro]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Its more efficient to test the register we're interested in first,
potentially avoiding two more comparisons, and therefore always avoiding
one comparison per call on all other chips.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: fix some checkpatch warnings]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
func0 is not provided by the mmc stack as a function when probing.
Instead providing specific access functions to read/write it.
This prepares for a patch to remove the actual array entry itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: rephrased the commit message]
[arend: removed unrelated comment for which separate patch is warranted]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rather than workaround the restrictions on func0 addressing in the
driver, set MMC_QUIRK_LENIENT_FN0
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IO functions operate within the Chipcommon IO window. Explicitly
set this, rather than relying on the last initialisation IO access to
leave it set to the right value by chance.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid confusion with unrelated _buscore labels.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: only do the rename]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove yet another IO function from the code and replace with one
that already exists.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: keep address calculation, ie. (base + offset) in one line]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer size of return of cap iovar is greater than 256 bytes in some
firmwares. For instance, the return size of cap iovar is 271 bytes in 4373
13.10.246.79 firmare. It makes feature capability parsing failed because
caps buffer is default value.
So we enlarge caps buffer size to 512 bytes and add the error print for
cap iovar error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to repeatdly call brcmf_chip_get_core(), which
traverses a list of cores every time its called (including during
register access code!).
Call it once, and store a pointer to the core structure. The existing
code does nto keep track of users of the cores anyway, and even so, this
will allow for easier refcounting in future.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro is used exactly nowhere in the code. Delete it.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Create a macro to make the code a bit more readable, whilst we're stuck
with using struct element offsets as register offsets.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: rename macro to SD_REG]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All functions that might require the window address changing call
brcmf_sdiod_set_backplane_window() prior to access. Thus resetting
the window is not required.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: corrected the driver prefix in the subject]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function has become trivial enough that it may as well be pushed into
its callers, which has the side-benefit of clarifying what's going on.
Remove it, and rename brcmf_sdiod_set_sbaddr_window() to
brcmf_sdiod_set_backplane_window() as it's easier to understand.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial tidy of register definitions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Primarily this patch removes:
brcmf_sdiod_f0_writeb()
brcmf_sdiod_reg_write()
brcmf_sdiod_reg_read()
Since we no longer use the quirky method of deciding which function to
address via the address being accessed, take the opportunity to rename
some IO functions more in line with common kernel code. We also convert
those that map directly to sdio_{read,write}*() to macros.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whilst this if () statement is technically correct, it lacks clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: mention function in patch subject]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function needs to be split up into separate read / write variants
for clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the ARRAY_SIZE macro on rfseq_updategainu_events to determine
size of the array. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed
Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial cleanup of nasty variable name
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If you need debugging this low level, you're doing something wrong.
Remove these noisy debug statements so the code is more readable.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unlikely to be a problem, but brcmf_sdiod_regrl() is
not symmetric with brcmf_sdiod_regrb() in initializing
the data value on stack. Fix that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: reword the commit message a bit]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is obfuscating how IO works on this chip. Remove it
and push its logic into brcmf_sdiod_reg_{read,write}().
Handling of -ENOMEDIUM is altered, but as that's pretty much broken anyway
we can ignore that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register access code is not the place for band-aid fixes like this.
If this is a genuine problem, it should be fixed further up in the driver
stack.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value passed to brcmf_sdiod_addrprep() is *always* 4
remove this parameter and the unused code to handle it.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function sets the address of the IO window used for
SDIO accesses onto the backplane of the chip.
It currently uses 3 separate masks despite the full mask being
defined in the code already. Remove the separate masks and clean up.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This large function is concealing a LOT of obscure logic about
how the hardware functions. Time to split it up.
This first patch splits the function into two pieces - read and write,
doing away with the rw flag in the process.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 4 IO functions in this patch are incorrect as they use compiler types
to determine how many bytes to send to the hardware.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the other IO functions are the other way round in this
driver. Make this one match.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the function brcmf_sdio_firmware_callback() the driver is
unbound from the sdio function devices in the error path.
However, the order in which it is done resulted in a use-after-free
issue (see brcmf_ops_sdio_remove() in bcmsdh.c). Hence change
the order and first unbind sdio function #2 device and then
unbind sdio function #1 device.
Cc: stable@vger.kernel.org # v4.12.x
Fixes: 7a51461fc2 ("brcmfmac: unbind all devices upon failure in firmware callback")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
The firmware for brcmfmac devices includes information regarding
regulatory constraints. For certain devices this information is kept
separately in a binary form that needs to be downloaded to the device.
This patch adds support to download this so-called CLM blob file. It
uses the same naming scheme as the other firmware files with extension
of .clm_blob.
The CLM blob file is optional. If the file does not exist, the download
process will be bypassed. It will not affect the driver loading.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration of the IEs for probe requests was done in a P2P
related function, which is not very obvious. Moving it to
.scan callback function, ie. brcmf_cfg80211_scan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field struct brcmf_cfg80211_info::active_scan is set to true upon
initializing the driver instance, but it is never changed so simply
get rid of it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() is only called by brcmf_cfg80211_scan()
so there is no reason to split in two function especially since the latter
does not do an awful lot.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor cleanup using provided macro to convert milliseconds interval
to jiffies in brcmf_cfg80211_escan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() was always called with a non-null
request parameter and null pointer for this_ssid parameter. Clean up
the function removing the dead code path.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable arp and nd offload to allow all packets sending to host.
Reported-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware uses a mailbox to communicate to the host what is going
on. In the driver we validate the bit received. Various people seen
the following message:
brcmfmac: brcmf_sdio_hostmail: Unknown mailbox data content: 0x40012
Bit 4 is cause of this message, but this actually indicates the firmware
has halted. Handle this bit by giving a more meaningful error message.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous commit I left the indentation alone to help reviewing
the patch, this one now runs the three new functions through 'indent -kr -8'
with some manual fixups to avoid silliness.
No changes other than whitespace are intended here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The stack consumption in this driver is still relatively high, with one
remaining warning if the warning level is lowered to 1536 bytes:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:17135:1: error: the frame size of 1880 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
The affected function is actually a collection of three separate implementations,
and each of them is fairly large by itself. Splitting them up is done easily
and improves readability at the same time.
I'm leaving the original indentation to make the review easier.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ5x32AAoJEG4XJFUm622b22EIAKmIlD1tAXxK9YAtYE5AnD5A
QpklYuVJA4XFtpN9UKXP/KCGTRnflW6i4RQ3dt6WKNULkL8RMAjwDijxXrFz8YXw
uB1Aw+Rbmx8eSrWKTgBCLlfU4J3j8jj5gSc7rzYeG7DnMFVShRCxRChiR09GhY4n
gXX3p4+migW128EyQ4KYYFGxipS+5/0igsSwqE6UIyxDuhINjCS9MipwXmv2uG+G
eYOSlwPE+LI8rObqlaJKVgam77srQqZLnPnima+bKAYXiQOPxPDBLwGP1qjo38Wa
pHKDG//OPMOjyUccl5axulnvLPTjyng9jYNpzJlLLz9+M29SudtHI7YQQHhBj5M=
=bApF
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
brcmf_fweh_process_event() sets event->datalen to the
endian-swapped value of event_packet->msg.datalen, which is the
same as emsg.datalen. This length is already validated in
brcmf_fweh_process_event(), so there is no need to check it
again upon dequeuing the event.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_p2p_notify_rx_mgmt_p2p_probereq(), chanspec is assigned before
the length of rxframe is validated. This could lead to uninitialized
data being accessed (but not printed). Since we already have a
perfectly good endian-swapped copy of rxframe->chanspec in ch.chspec,
and ch.chspec is not modified by decchspec(), avoid the extra
assignment and use ch.chspec in the debug print.
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With KASAN and a couple of other patches applied, this driver is one
of the few remaining ones that actually use more than 2048 bytes of
kernel stack:
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy_gainctrl':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:16065:1: warning: the frame size of 3264 bytes is larger than 2048 bytes [-Wframe-larger-than=]
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:17138:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Here, I'm reducing the stack size by marking as many local variables as
'static const' as I can without changing the actual code.
This is the first of three patches to improve the stack usage in this
driver. It would be good to have this backported to stabl kernels
to get all drivers in 'allmodconfig' below the 2048 byte limit so
we can turn on the frame warning again globally, but I realize that
the patch is larger than the normal limit for stable backports.
The other two patches do not need to be backported.
Cc: <stable@vger.kernel.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of the data in the received skb is currently passed into
brcmf_fweh_process_event() as packet_len, but this value is not checked.
event_packet should be followed by DATALEN bytes of additional event
data. Ensure that the received packet actually contains at least
DATALEN bytes of additional data, to avoid copying uninitialized memory
into event->data.
Cc: <stable@vger.kernel.org> # v3.8
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const arrays on the stack, instead make them static.
Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
14816 1296 0 16112 3ef0 b43/phy_ht.o
After:
text data bss dec hex filename
14551 1496 0 16047 3eaf b43/phy_ht.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const array ucode_ofdm_rates on the stack, instead make it
static. Makes the object code smaller by 100 bytes:
Before:
text data bss dec hex filename
39482 564 0 40046 9c6e phy_cmn.o
After
text data bss dec hex filename
39326 620 0 39946 9c0a phy_cmn.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u8 char array ret is not being initialized and elements outside
the range start to end contain just garbage values from the stack.
This results in a later scan of the array to read potentially
uninitialized values. Fix this by initializing the array to zero.
This seems to have been an issue since the very first commit.
Detected by CoverityScan CID#139653 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The u8 char array ret is not being initialized and elements outside
the range start to end contain just garbage values from the stack.
This results in a later scan of the array to read potentially
uninitialized values. Fix this by initializing the array to zero.
This seems to have been an issue since the very first commit.
Detected by CoverityScan CID#139652 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was not properly configuring firmware with regard to the
type of scan. It always performed an active scan even when user-space
was requesting for passive scan, ie. the scan request was done without
any SSIDs specified.
Cc: stable@vger.kernel.org # v4.0.x
Reported-by: Huang, Jiangyang <Jiangyang.Huang@itron.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon handling the firmware notification for scans the length was
checked properly and may result in corrupting kernel heap memory
due to buffer overruns. This fix addresses CVE-2017-0786.
Cc: stable@vger.kernel.org # v4.0.x
Cc: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware feature check introduced for multi-scheduled scan is also
failing for bcm4345 devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For debugging some problems, it is useful to know the chip revision
add a brcmf_info message logging this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
The firmware feature check introduced for multi-scheduled scan turned out
to be failing for bcm4343{0,1,8} devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After association, ping is not working when sweeping the channel at the
AP side. It is caused by having incorrect carrier state (OFF) for the STA
in successful roaming. This patch sets the carrier state ON for the case.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device/firmware supports multi-channel, it can have P2P
connection and regular connection with AP simultaneous. In this case,
the num_different_channels in wiphy info was not correct when firmware
supports multi-channel (The iw wiphy# info showed "#channels <= 1" in
interface combinations). It caused association failed and error message
"CTRL-EVENT-FREQ-CONFLICT error" in wpa_supplicant when P2P GO interface
was running at the same time.
The root cause is that the num_different_channels was always overridden
to 1 in brcmf_setup_ifmodes even multi-channel was enabled.
We correct the logic by moving num_different_channels setting forward.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When setting wpa_auth to WPA_AUTH_NONE(1) in AP mode with WEP security,
firmware will set privacy bit and add WPA OUI in VENDOR IE in beacon and
probe response. The security type in softAP beacons confuse the
supplicant in client side, and the user client will see [WPA-?] in
supplicant scan result. So we set WPA_AUTH_DISABLED in softAP mode with
OPEN security.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to a bugfix in wireless tree and the commit mentioned below a merge
was needed which went haywire. So the submitted change resulted in the
function brcmf_sdiod_sgtable_alloc() being called twice during the probe
thus leaking the memory of the first call.
Cc: stable@vger.kernel.org # 4.6.x
Fixes: 4d79289598 ("brcmfmac: switch to new platform data")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit to rework the headroom check in start_xmit() now calls
pxskb_expand_head() unconditionally if the header is CoW. Unfortunately,
it does so with the delta between the extant headroom and the header
length, which may be negative if there is already sufficient headroom.
pskb_expand_head() does allow for size being 0, in which case it just
copies, so clamp the header delta to zero.
Opening Chrome (and all my tabs) on a PCIE device was enough to reliably
hit this.
Fixes: 270a6c1f65 ("brcmfmac: rework headroom check in .start_xmit()")
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
