The intent was to expose these as part of the means to perform full
context recovery (though not the SINGLE_TIMELINE, that is for later and
just sucked as collateral damage). As that requires a couple more
patches to complete the series, roll back the earlier chunks of ABI for
an intervening PR. We keep all the internals intact and under selftests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327105814.14694-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This is to disable semaphore usage when on vGPU for now. Unfortunately
GVT-g hasn't fully enabled semaphore usage yet, so current guest with
semaphore use would cause vGPU failure.
Although current semaphore failure with vGPU can be simply resolved by
allowing cmd parser to accept MI_SEMAPHORE_WAIT command with address
audit, we're checking general usage of semaphore and how we should
handle it properly for virtualization in consider of function and
security concern. So we decide to request to disable it for now in
guest driver. Once GVT could support it, we would add new compat bit
to turn it on.
Fixes: e886196469 ("drm/i915: Use HW semaphores for inter-engine synchronisation on gen8+") #vgpu
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327090636.3547-1-zhenyuw@linux.intel.com
Update the DP MSA MISC bits for fastsets. This is needed
when we change between limited and full range RGB output.
On HSW+ changing limited_range does not currently result in a
full modeset since we have don't have the readout code for it
(for DP we could, and probably should, readout from TRANS_MSA_MISC
itself, for HDMI we would have to rely on the infoframe). So
the PIPE_CONF_CHECK() is only performed for pre-HSW platforms.
That means any change in the value will result in a fastset
instead. Fortunately there is no prohibition to changing
TRANS_MSA_MISC dynamically, so it looks like we can legally do
fastsets for this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-5-ville.syrjala@linux.intel.com
Allow DP MST to output any color depth. This means deep color as
well as falling back to 6bpc if we would otherwise require too
much bandwidth.
TODO: We should probably extend bw_contstrained scheme to force
all streams on the link to 6bpc if we can't fit the new stream(s)
otherwise.
v2: Use a proper for-loop (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-3-ville.syrjala@linux.intel.com
When building with ARCH=i386, readq and writeq are not defined,
resulting in:
intel_uncore.h: In function ‘__raw_uncore_read64’:
intel_uncore.h:257:9: error: implicit declaration of function ‘readq’;
did you mean ‘readl’? [-Werror=implicit-function-declaration]
return read##s__(uncore->regs + i915_mmio_reg_offset(reg)); \
^
and:
intel_uncore.h: In function ‘__raw_uncore_write64’:
intel_uncore.h:264:2: error: implicit declaration of function ‘writeq’;
did you mean ‘writel’? [-Werror=implicit-function-declaration]
write##s__(val, uncore->regs + i915_mmio_reg_offset(reg)); \
^
Add the io-64-nonatomic-lo-hi include to have readq and writeq available
for all builds. This header internally includes linux/io.h, so the
native readq and writeq definitions will be used when available.
Fixes: 6cc5ca7688 ("drm/i915: rename raw reg access functions")
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326233817.5417-1-daniele.ceraolospurio@intel.com
Tvrtko spotted that I left off the trailing ';'. It went unnoticed by CI
because despite adding the macro, we didn't add a user, so include one as
well (a simple debug print).
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 97ee6e9255 ("drm/i915: stop storing the media fuse")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326180007.11722-1-chris@chris-wilson.co.uk
Since GEM_CREATE is trying to outsmart the user by rounding up unaligned
objects, we used to update the size returned to userspace.
This update seems to have been lost throughout the history.
v2: Use round_up(), reorder locals (Chris)
References: ff72145bad ("drm: dumb scanout create/mmap for intel/radeon (v3)")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Janusz Krzysztofik <janusz.krzysztofik@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326170218.13255-1-michal.winiarski@intel.com
A few advantages:
- Prepares us for the planned split of display uncore from GT uncore
- Improves our engine-centric view of the world in the engine code
and allows us to avoid jumping back to dev_priv.
- Allows us to wrap accesses to engine register in nice macros that
automatically pick the right mmio base.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-10-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of register access, so
subclass the function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-9-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of register access, so
subclass the function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-8-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of FW, so subclass the
function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-7-daniele.ceraolospurio@intel.com
The full read/write ops can now work on the intel_uncore struct.
Introduce intel_uncore_read/write functions working on intel_uncore
and switch the I915_READ/WRITE macro to internally call those.
v2: no change
v3: add intel_uncore_read/write functions (Chris), update commit msg
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-6-daniele.ceraolospurio@intel.com
Save the HW capabilities to avoid having to jump back to dev_priv
every time.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-4-daniele.ceraolospurio@intel.com
We have several cases where we don't have forcewake (older gens, GVT and
planned display-only uncore), so, instead of checking every time against
the various condition, save the info in a flag and use that.
Note that this patch also change the behavior for gen5 with vpgu
enabled, but this is not an issue since we don't support vgpu on gen5.
v2: split out from previous path, fix check for missing case (Paulo)
v3: Inline helper for clarity in testing flags
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-3-daniele.ceraolospurio@intel.com
They now work on uncore, so use raw_uncore_ prefix. Also move them to
uncore.h
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-2-daniele.ceraolospurio@intel.com
By the time icl_ddi_clock_get() is called we've just got the hw state
from the pll registers. We don't need to read them again: we can rather
reuse what was cached in the dpll_hw_state.
While at it, s/refclk/ref_clock/ just to be consistent with the name
used in code nearby.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-5-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
By the time cnl_ddi_clock_get() is called we've just got the hw state
from the pll registers. We don't need to read them again: we can rather
reuse what was cached in the dpll_hw_state.
This also affects the code for ICL since it partially reuses the CNL
code. However the more intricate part on ICL is left for another patch.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-4-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rename state to pll_state and use it as the argument to
bxt_calc_pll_link(), similar to how it's done in the skl variant.
The WARN_ON(!crtc_state->shared_dpll) is not very useful, so remove it
as well.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-3-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
By the time skl_ddi_clock_get() is called - and thus
skl_calc_wrpll_link() - we've just got the hw state from the pll
registers. We don't need to read them again: we can rather reuse what
was cached in the dpll_hw_state.
v2: rename state variable to pll_state, make argument const in
skl_calc_wrpll_link() and remove not useful warning (from Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-2-lucas.demarchi@intel.com
The live_context() function returns error pointers. It never returns
NULL.
Fixes: 9c1477e83e ("drm/i915/selftests: Exercise adding requests to a full GGTT")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326050843.GA20038@kadam
We're already updating the engine_mask to reflect what's in the HW, so
we can just get the info from there. A couple of macros have been added
to facilitate this.
v2: Appease checkpatch
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322002431.9585-1-daniele.ceraolospurio@intel.com
Iterate over child devices instead of ports in parse_ddi_ports() to
initialize ddi_port_info. We'll eventually need to decide some stuff
based on the child device order, which may be different from the port
order.
As a bonus, this allows better abstractions for e.g. dvo port mapping.
There's a subtle change in the DDC pin and AUX channel sanitization as
we change the order. Otherwise, this should not change behaviour.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322121008.4456-1-jani.nikula@intel.com
Fixup the errno as we adjusted the error path to receive the errno and
not compute it itself from ERR_PTR(ctx) anymore.
drivers/gpu/drm/i915/i915_gem_context.c:793 i915_gem_context_open() warn: passing a valid pointer to 'PTR_ERR'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3aa9945a52 ("drm/i915: Separate GEM context construction and registration to userspace")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325090413.19906-2-chris@chris-wilson.co.uk
The AGPBUSY thing doesn't work on i945gm anymore. This means
the gmch is incapable of waking the CPU from C3 when an interrupt
is generated. The interrupts just get postponed indefinitely until
something wakes up the CPU. This is rather annoying for vblank
interrupts as we are unable to maintain a steady framerate
unless the machine is sufficiently loaded to stay out of C3.
To combat this let's use pm_qos to prevent C3 whenever vblank
interrupts are enabled. To maintain reasonable amount of powersaving
we will attempt to limit this to C3 only while leaving C1 and C2
enabled.
v2: Use READ_ONCE() (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30364
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322180804.3300-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
If I'm reading the spec right AML 0x87CA is a Y SKU, so it
should be marked as ULX in our old style terminology.
Cc: stable@vger.kernel.org
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: c0c46ca461 ("drm/i915/aml: Add new Amber Lake PCI ID")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322204944.23613-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Since commit b7137e0cf1 ("drm/i915: Defer enabling rc6 til after we
submit the first batch/context"), intel_suspend_gt_powersave() has been
a no-op. As we still do not need to do anything explicitly on suspend
(we do everything required on idling), remove the defunct function.
References: b7137e0cf1 ("drm/i915: Defer enabling rc6 til after we submit the first batch/context")
Suggested-by: "Hiatt, Don" <don.hiatt@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190323214009.23294-1-chris@chris-wilson.co.uk
GuC may send notification messages with payload larger than
single u32. Prepare driver to accept longer messages.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321120004.53012-1-michal.wajdeczko@intel.com
Initially found issue with closed context debug check when pin
hw_id for GVT context, looks we should always pin hw_id for that
as GVT context is fixed for each vGPU life cycle, and we'd also
like to get pinned hw_id e.g for perf reason, etc.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190311023747.1426-1-zhenyuw@linux.intel.com
EHL uses the same firmware as ICL.
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-6-rodrigo.vivi@intel.com
EHL has a different number of subslices.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-5-rodrigo.vivi@intel.com
Configure the correct set of outputs for EHL. EHL has three DDI's
plus DSI.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-4-rodrigo.vivi@intel.com
Elkhart Lake has a different set of PLLs as compared to Ice Lake,
although programming them is very similar.
v2: Rebase on top of s/icl_pll_funcs/combo_pll_funcs
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-3-rodrigo.vivi@intel.com
Add ElkhartLake as a unique platform as there are some differences
between it and Icelake.
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-2-rodrigo.vivi@intel.com
Add known EHL PCI IDs.
v2 (Rodrigo): Removed x86 early quirk. To be sent in a separated
patch cc'ing the appropriated list and maintainers for
proper ack.
v3: (Rodrigo): - Removed .num_pipes = 3 that is coming since GEN&_FEATURES.
- Added ppgtt type and size after rework from Bob and Chris
v4: (Rodrigo): - remove ppgtt type added on v3. Jose pointed it is not
needed.
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-1-rodrigo.vivi@intel.com
Rename intel_find_panel_downclock() to intel_panel_edid_downclock_mode()
to make it clear it's looking for the downclock mode in the EDID.
And while at it polish the implementation a bit as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Some monitors apparently forget to mark any mode as preferred in the
EDID. In this particular case we have a very generic looking ID
"PNP Model 0 Serial Number 4" / "LVDS 800x600" so a specific quirk
doesn't seem particularly wise. Also the quirk we have
(EDID_QUIRK_FIRST_DETAILED_PREFERRED) is actually defunct so we'd
have to fix it first.
When there is no preferred mode we currently fall back to the VBT.
That approach fails us here as the VBT mode is 1024x768 whereas
the panel resolution is 800x600. So instead of falling back to the
VBT when there is no preferred mode let's just pick the first
probed mode. Only if the EDID provided no modes we fall back to
the VBT.
For this machine the VBIOS would appear to select the 800x600
60Hz EST mode rather than the first detailed mode (which is
the new fallback will pick). The two modes differ only by
having opposite sync polarities, which does not seem to matter
to the panel in question.
v2: Make sure the probed_modes list is not empty
Cc: Adam Jackson <ajax@redhat.com>
Cc: Roberto Viola <cagnulein@gmail.com>
Tested-by: Roberto Viola <cagnulein@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109780
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-2-ville.syrjala@linux.intel.com
Reviewed-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Both LVDS and eDP have the same code to look up the preferred mode
from the connector probed_modes list. Move the code to a common
location.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
I added the loop but neglected to actually pass the level to the
function. So we were just looping 8 times calculating the exact
same thing every time.
Fixes: df331de3f8 ("drm/i915: Allocate enough DDB for the cursor")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321175128.32178-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Previously, our view has been always to run the engines independently
within a context. (Multiple engines happened before we had contexts and
timelines, so they always operated independently and that behaviour
persisted into contexts.) However, at the user level the context often
represents a single timeline (e.g. GL contexts) and userspace must
ensure that the individual engines are serialised to present that
ordering to the client (or forgot about this detail entirely and hope no
one notices - a fair ploy if the client can only directly control one
engine themselves ;)
In the next patch, we will want to construct a set of engines that
operate as one, that have a single timeline interwoven between them, to
present a single virtual engine to the user. (They submit to the virtual
engine, then we decide which engine to execute on based.)
To that end, we want to be able to create contexts which have a single
timeline (fence context) shared between all engines, rather than multiple
timelines.
v2: Move the specialised timeline ordering to its own function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-4-chris@chris-wilson.co.uk
It can be useful to have a single ioctl to create a context with all
the initial parameters instead of a series of create + setparam + setparam
ioctls. This extension to create context allows any of the parameters
to be passed in as a linked list to be applied to the newly constructed
context.
v2: Make a local copy of user setparam (Tvrtko)
v3: Use flags to detect availability of extension interface
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-3-chris@chris-wilson.co.uk
