When CONFIG_MTD_PARTITIONED_MASTER=y, it is fatal to call
mtd_device_parse_register() twice on the same MTD, as we try to register
the same device/kobject multipile times.
When CONFIG_MTD_PARTITIONED_MASTER=n, calling
mtd_device_parse_register() is more of just a nuisance, as we can mostly
navigate around any conflicting actions.
But anyway, doing so is a Bad Thing (TM), and we should complain loudly
for any drivers that try to do this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Since commit 3efe41be22 ("mtd: implement common reboot notifier
boilerplate"), we might try to register a reboot notifier for an MTD
that failed to register. Let's avoid this by making the error path
clearer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Changes the 32-bit time type timeval to the 64-bit time type
ktime_t, since 32-bit systems using struct timeval will break in the
year 2038. Correspondingly change do_gettimeofday() to ktime_get()
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval.Here, ktime_get() is used instead of ktime_get_real()
since ktime_get() uses monotonic clock.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your nand controller
DT node:
nand-ecc-mode = "soft_bch";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If nand_wait_ready() times out, this is silently ignored, and its
caller will then proceed to read from/write to the chip before it is
ready. This can potentially result in corruption with no indication as
to why.
While a 20ms timeout seems like it should be plenty enough, certain
behaviour can cause it to timeout much earlier than expected. The
situation which prompted this change was that CPU 0, which is
responsible for updating jiffies, was holding interrupts disabled
for a fairly long time while writing to the console during a printk,
causing several jiffies updates to be delayed. If CPU 1 happens to
enter the timeout loop in nand_wait_ready() just before CPU 0 re-
enables interrupts and updates jiffies, CPU 1 will immediately time
out when the delayed jiffies updates are made. The result of this is
that nand_wait_ready() actually waits less time than the NAND chip
would normally take to be ready, and then read_page() proceeds to
read out bad data from the chip.
The situation described above may seem unlikely, but in fact it can be
reproduced almost every boot on the MIPS Creator Ci20.
Therefore, this patch increases the timeout to 400ms. This should be
enough to cover cases where jiffies updates get delayed. In nand_wait()
the timeout was previously chosen based on whether erasing or
programming. This is changed to be 400ms unconditionally as well to
avoid similar problems there. nand_wait() is also slightly refactored
to be consistent with nand_wait{,_status}_ready(). These changes should
have no effect during normal operation.
Debugging this was made more difficult by the misleading comment above
nand_wait_ready() stating "The timeout is caught later" - no timeout was
ever reported, leading me away from the real source of the problem.
Therefore, a pr_warn() is added when a timeout does occur so that it is
easier to pinpoint similar problems in future.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Smatch found a bug in the error handling:
drivers/mtd/devices/docg3.c:1634 doc_register_sysfs()
error: buffer overflow 'doc_sys_attrs' 4 <= 4
The problem is that if the very last device_create_file() fails, then we
are beyond the end of the array. Actually, any time i == 3 then there
is a problem. We can fix this an simplify the code at the same time by
moving the !ret conditions out of the for loops and using a goto
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the previous modifications, lots of pxa3xx specific definitions can
be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Rework the pxa3xx_nand driver to allow using functions exported by the
nand framework to detect the flash and the timings. Then setup the
timings using the helpers previously added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helpers to setup the timings in the pxa3xx driver. These helpers
allow to either make use of the nand framework nand_sdr_timings or the
pxa3xx specific pxa3xx_nand_host, for compatibility reasons.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using readsl() result in a build error on i386. Fix this by using
ioread32_rep() instead, to allow compile testing the pxa3xx nand driver
on other architectures later.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #206
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x208/0x248)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #201
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x290/0x568)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We got the syntax wrong here. Compile tested this time!
Error:
drivers/mtd/maps/rbtx4939-flash.c: In function 'rbtx4939_flash_probe':
>> drivers/mtd/maps/rbtx4939-flash.c:99:11: error: request for member 'dev' in something not a structure or union
info->mtd.dev.parent = &dev->dev;
^
Fixes: 9aa7e50276 ("mtd: maps: rbtx4939-flash: show parent device in sysfs")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Frans Klaver <fransklaver@gmail.com>
We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The old PM model is deprecated. This is equivalent.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mtd_{suspend,resume}() get called from mtdcore in a class suspend/resume
callback. We don't need to call them again here. In practice, this would
actually work OK, as nand_base actually handles nesting OK -- it just
might print warnings.
Untested, but there are few (no?) users of PM for this driver AFAIK.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Building for x86 results in the following build errors:
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
>> drivers/mtd/spi-nor/fsl-quadspi.c:355:21: error: 'SZ_16M' undeclared (first use in this function)
if (q->nor_size <= SZ_16M) {
^
drivers/mtd/spi-nor/fsl-quadspi.c:355:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
>> drivers/mtd/spi-nor/fsl-quadspi.c:208:27: error: 'SZ_4M' undeclared (first use in this function)
#define QUADSPI_MIN_IOMAP SZ_4M
^
>> drivers/mtd/spi-nor/fsl-quadspi.c:845:25: note: in expansion of macro 'QUADSPI_MIN_IOMAP'
q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
Explicitly include <linux/sizes.h> to fix the problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't actually need ARCH_MXC to compile. Relax the
constraints.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Seen when compile-testing on non-32-bit arch:
CC drivers/mtd/spi-nor/fsl-quadspi.o
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
drivers/mtd/spi-nor/fsl-quadspi.c:873:2: warning: format '%d' expects argument of type 'int', but argument 6 has type 'size_t' [-Wformat=]
dev_dbg(q->dev, "cmd [%x],read from 0x%p, len:%d\n",
^
Also drop the '0x' prefixing to the '%p' formatter, since %p already
knows how to format pointers appropriately.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Many other flash share the same features as ST Micro. I've tested some
Winbond flash, so add them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This code was a bit sloppy, would produce a lot of copy-and-paste, and
did not always provide a sensible interface:
* It didn't validate the length for LOCK and the offset for UNLOCK, so
we were essentially discarding half of the user-supplied data and
assuming what they wanted to lock/unlock
* It didn't do very good error checking
* It didn't make use of the fact that this operation works on
power-of-two dimensions
So, rewrite this to do proper bit arithmetic rather than a bunch of
hard-coded condition tables. Now we have:
* More comments on how this was derived
* Notes on what is (and isn't) supported
* A more exendible function, so we could add support for other
protection ranges
* More accurate locking - e.g., suppose the top quadrant is locked (75%
to 100%); then in the following cases, case (a) will succeed but (b)
will not (return -EINVAL):
(a) user requests lock 3rd quadrant (50% to 75%)
(b) user requests lock 3rd quadrant, minus a few blocks (e.g., 50%
to 73%)
Case (b) *should* fail, since we'd have to lock blocks that weren't
requested. But the old implementation didn't know the difference and
would lock the entire second half (50% to 100%)
This refactoring work will also help enable the addition of
mtd_is_locked() support and potentially the support of bottom boot
protection (TB=1).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->read_xxx() methods are all passed the page number the NAND controller
is supposed to read, but ->write_xxx() do not have such a parameter.
This is a problem if we want to properly implement data
scrambling/randomization in order to mitigate MLC sensibility to repeated
pattern: to prevent bitflips in adjacent pages in the same block we need
to avoid repeating the same pattern at the same offset in those pages,
hence the randomizer/scrambler engine need to be passed the page value
in order to adapt its seed accordingly.
Moreover, adding the page parameter to the ->write_xxx() methods add some
consistency to the current API.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Huang Shijie <shijie.huang@arm.com>
CC: Stefan Agner <stefan@agner.ch>
CC: devel@driverdev.osuosl.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner and name are automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Make sure the device structure is properly shown in sysfs by properly
filling in dev.parent.
While at it, make use of the default owner and name values set by
mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, take advantage of the default owner and name values set by
mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner and name set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner and name are automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Incidentally, it seems the owner field in the concatenated mtds is not
actually used, so this shouldn't make much of a difference anyway.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a parent device is set, add_mtd_device() has enough knowledge to fill
in some sane default values for the module name and owner. Do so if they
aren't already set.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
add_mtd_device() has a comment suggesting that the caller should have
set dev.parent. This is required to have the parent device symlink show
up in sysfs, but not for proper operation of the mtd device itself.
Currently we have five drivers registering mtd devices during module
initialization, so they don't actually provide a parent device to link
to. That means we cannot WARN_ON() here, as it would trigger false
positives.
Make the comment a bit less firm in its assertion that dev.parent should
be set.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The N25Q032A is identical to the N25Q032 except it has a different
supply voltage range. Therefore, it has a new JEDEC ID.
Signed-off-by: Aurelien Chanot <chanot.a@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The BRCM NAND driver can be re-used for Broadcom ARM64 SoCs hence
this patch updates Kconfig to allow selection of MTD_NAND_BRCMNAND
for ARM64.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should always type-cast pointer to "long" or "unsigned long"
because size of pointer is same as machine word size. This will
avoid pointer type-cast issues on both 32bit and 64bit systems.
This patch fixes pointer type-cast issue in brcmnand_write()
as-per above info.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation for deprecating ioremap_cache() convert its usage in
pxa2xx-flash to memremap.
Cc: David Woodhouse <dwmw2@infradead.org>
[brian: also convert iounmap to memunmap]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The probe of a mtd device can fail when a partition parser returns
error. The failure due to partition parsing can be quite mysterious when
multiple partitioning schemes are compiled in and any of them can fail
the probe.
Add debug prints which show what parsers were tried and what they
returned.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* mxc_nand: a "refactoring only" change in 4.3-rc1 had some bad pointer
(array) arithmetic. Fix that
* sunxi_nand:
- Fix an old list manipulation / memory management bug in the device
release() code path
- Correct a few mistakes in OOB write support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=A7qE
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151006' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"A few MTD fixes:
- mxc_nand: a "refactoring only" change in 4.3-rc1 had some bad
pointer (array) arithmetic. Fix that
- sunxi_nand:
- Fix an old list manipulation / memory management bug in the device
release() code path
- Correct a few mistakes in OOB write support"
* tag 'for-linus-20151006' of git://git.infradead.org/linux-mtd:
mxc_nand: fix copy_spare
mtd: nand: sunxi: fix sunxi_nand_chips_cleanup()
mtd: nand: sunxi: fix OOB handling in ->write_xxx() functions
According to LPC32xx User's Manual all values measured in clock cycles
are programmable from 1 to 16 clocks (4 bits) starting from 0 in
bitfield, the current version of calculated clock cycles is too
conservative.
Correctness of 0 bitfield value (i.e. programmed 1 clock
timing) is proven with actual NAND chip devices.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case if quotient of controller clock rate to device clock rate does
not fit into 4 bit value, choose the maximum acceptable value 0xF, which
stands for 16 clocks.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
No functional change, move bitfield calculations to macro
definitions with added clock rate argument, which are in turn defined
by new common SLCTAC_CLOCKS(c, n, s) macro definition.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If fastmap requests a free PEB for a pool and UBI is busy
with erasing PEBs we need to offer a function to wait for one.
We can reuse produce_free_peb() from the non-fastmap WL code
but with different locking semantics.
Cc: stable@vger.kernel.org # 4.1.x-
Reported-and-tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Richard Weinberger <richard@nod.at>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch trivially updates code comments to reflect the addition of the
UBI_METAONLY flag - as discussed https://lkml.org/lkml/2014/10/29/764
Cc: Richard Weinberger <richard@nod.at>
Cc: trivial@kernel.org
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
We have to use j instead of i. i is the volume id
and not the block.
Reported-by: Alexander.Block@continental-corporation.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Use the nand_check_erased_ecc_chunk() function to test if the ECC error
was triggered by an erased page containing a few bitflips.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
sunxi_nfc_user_data_to_buf() is exposed as an inline function, replace the
NFC_BUF_TO_USER_DATA() macro by an inline function to be consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ECC engine is protecting a few OOB bytes. Retrieve them from the
USER_DATA register instead of reading them in raw mode (ie without the ECC
protection).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helper functions to factorize the code dealing extra OOB bytes in the
normal and syndrome ECC implementations.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions have been created to
factorize the code in the normal and syndrome ECC implementation.
Make use of them where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The logic behind normal and syndrome ECC handling is pretty much the same,
the only difference is the ECC bytes placement.
Create two functions to read/write ECC chunks. Those functions will later
be used by the sunxi_nfc_hw_ecc_read/write_page() and
sunxi_nfc_hw_syndrome_ecc_read/write_page() functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The code used to enable/disable the hardware ECC engine is repeated in a
lot of places. Create two functions to avoid code duplication.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->init_size() hook was introduced to let NAND controller drivers
support NAND devices that could not be described in the nand_ids table.
Since then, the core has added support for extended-id parsing and
full-id description, thus allowing to describe pretty much all existing
NANDs.
Moreover, this hook is not used by any mainline driver, and should not be
used by new drivers, because detecting the NAND chip is not something
controller specific.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These really aren't needed, especially now that we embed the soc struct
in our private struct, so we can stash things there if needed.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Suffix mask macros with _MSK and add new helper macros to avoid manually
shifting values.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This must have been implicitly included on the builds I tested. Reported
by numerous test bots:
drivers/mtd/nand/vf610_nfc.c: In function 'vf610_nfc_resume':
drivers/mtd/nand/vf610_nfc.c:660:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This reverts commit 7827e3acad.
There are some 64-bit arithmetic issues on some architectures, so let's
wait until we get a better patch for this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).
Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.
Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.
Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.
Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.
Colibri VF50
eb write % eb read % page write % page read %
rel/opt 5175 11537 4560 11039
opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10
none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58
Colibri VF61
eb write % eb read % page write % page read %
rel/opt 5766 13096 5459 12846
opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34
none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86
rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write
The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After a bit of poking around wondering why my 32-bit user-space can't
seem to send a proper ioctl(BLKPG) to an MTD on my 64-bit kernel
(ARM64), I noticed that struct blkpg_ioctl_arg is actually pretty
unsuitable for use in the ioctl() ABI, due to its use of raw pointers,
and its lack of alignment/packing restrictions (32-bit arch'es tend to
pack the 4 fields into 4 32-bit words, whereas 64-bit arch'es would add
padding after the third int, and make this 6 32-bit words).
Anyway, this means BLKPG deserves some special compat_ioctl handling. Do
the conversion in a small shim for MTD.
block/compat_ioctl.c already has compat support for the block subsystem,
but it does so by a re-marshalling data to/from user-space (see
compat_blkpg_ioctl()). Personally, I think this approach is cleaner.
Tested only on MTD, with an ARM32 user space on an ARM64 kernel.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes timeout issues seen on large NOR flash (e.g., 16MB
w25q128fw) when using ioctl(MEMERASE) with offset=0 and length=16M. The
input parameters matter because spi_nor_erase() uses a different code
path for full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode.
Fix: use a different timeout for full-chip erase than for other
commands.
While most operations can be expected to perform relatively similarly
across a variety of NOR flash types and sizes (and therefore might as
well use a similar timeout to keep things simple), full-chip erase is
unique, because the time it typically takes to complete:
(1) is much larger than most operations and
(2) scales with the size of the flash.
Let's base our timeout on the original comments stuck here -- that a 2MB
flash requires max 40s to erase.
Small survey of a few flash datasheets I have lying around:
Chip Size (MB) Max chip erase (seconds)
---- -------- ------------------------
w25q32fw 4 50
w25q64cv 8 30
w25q64fw 8 100
w25q128fw 16 200
s25fl128s 16 ~256
s25fl256s 32 ~512
From this data, it seems plenty sufficient to say we need to wait for
40 seconds for each 2MB of flash.
After this change, it might make some sense to decrease the timeout for
everything else, as even the most extreme operations (single block
erase?) shouldn't take more than a handful of seconds. But for safety,
let's leave it as-is. It's only an error case, after all, so we don't
exactly need to optimize it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 512KiB flash with 4 KiB erase sectors.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The module pcmciamtd doesn't generate a mtd node for PRETEC 4MB SRAM
cards without the id and hash added to pcmciamtd.c
Tested on 3 different 4MB pretec sram cards.
Signed-off-by: Tom Englund <tomenglund26@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A read id operation followed by 0x00 reads the device ID while
a read id operation followed by 0x20 reads the possible ONFI identifier.
As the READID function did not propagate the second id parameter but had
a hard-coded call for 0x90 0x00, reading the ONFI identifier was not
possible and thus chips werde not detected (tested with
MT29F8G08ABABAWP)
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch trivially updates code comments to reflect the addition of the
UBI_METAONLY flag - as discussed https://lkml.org/lkml/2014/10/29/764
Cc: Richard Weinberger <richard@nod.at>
Cc: trivial@kernel.org
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
This driver uses some custom macros for printing. Let's use the standard
pr_fmt()/pr_{err,warn}().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I'm not sure why we have a PAGE_SIZE restriction on this partition
parser.
If we really wanted the restriction, I would expect it to be a
restriction for *all* parsers, so we'd move it to the MTD core
At any rate, while small partitions may not be useful (they'll often be
smaller than the eraseblock size and therefore can only be used
read-only), they still have use as a read-only partition.
This restriction is especially annoying because it aborts the entire
MTD's cmdline parsing, leaving it unpartitioned.
So, let's kill the restriction and only check for zero-sized partitions,
which I expect we don't want to allow.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s25fl016k can be found on Embedded Artists' LPC4357 Developer's Kit
where is used in quad mode by the LPC4357 SPIFI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After the conversion of pxa architecture to common clock framework, the
NAND clock can be disabled on driver exit.
In this case, it happens that if the driver used the NAND and set the
DFI arbitration bit, the next access to a static memory controller area,
such as an ethernet card, will stall the system bus, and the core will
be stalled forever.
This is especially true on pxa31x SoCs, where the NDCR was augmented
with a new bit to prevent this lockups by giving full ownership of the
DFI arbiter to the SMC, in change SCr#6.
Fix this by clearing the DFI arbritration bit in driver exit. This
effectively prevents a lockup on zylonite when removing pxa3xx-nand
module, and using ethernet afterwards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In drivers/mtd/mtd_blkdevs.c:
406 set_capacity(gd, (new->size * tr->blksize) >> 9);
The type of new->size is unsigned long and the type of tr->blksize is int,
the result of 'new->size * tr->blksize' may exceed ULONG_MAX on 32bit
machines.
I use nand chip MT29F32G08CBADBWP which is 4GB and the parameters passed
to kernel is 'mtdparts=gpmi-nand:-(user)', the whole nand chip will be
treated as a 4GB mtd partition. new->size is 0x800000 and tr->blksize is
0x200, 'new->size * tr->blksize' however is 0. This is what we do not want
to see.
Using type cast u64 to fix the multiplication overflow issue.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now pxa architecture has a dmaengine driver, remove the access to direct
dma registers in favor of the more generic dmaengine code.
This should be also applicable for mmp and orion, provided they work in
device-tree environment.
This patch also removes the previous hack which was necessary to make
the driver work in a devicetree environment.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Brian: fixup use of 'enum dma_transfer_direction']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nand_chips_cleanup() function is missing a call to list_del()
which generates a double free error.
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add two helper functions to help NAND controller drivers test whether a
specific NAND region is erased or not.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The USER_DATA register cannot be accessed using byte accessors on A13
SoCs, thus triggering a bug when using memcpy_toio on this register.
Declare an helper macros to convert an OOB buffer into a suitable
USER_DATA value and vice-versa.
This patch also fixes an error in the oob_required logic (some OOB data
are not written even if the user required it) by removing the
oob_required condition, which is perfectly valid since the core already
fill ->oob_poi with FFs when oob_required is false.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
