Adding a debug log when the DP_AUX_NATIVE_REPLY_ACK is missing
for aksv write. This helps to locate the possible non responding
DP HDCP sinks.
v2:
Rewritten for readability [Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544010283-20223-4-git-send-email-ramalingam.c@intel.com
According to DP spec (2.9.3.1 of DP 1.4) if
EXTENDED_RECEIVER_CAPABILITY_FIELD_PRESENT is set the addresses in DPCD
02200h through 0220Fh shall contain the DPRX's true capability. These
values will match 00000h through 0000Fh, except for DPCD_REV,
MAX_LINK_RATE, DOWN_STREAM_PORT_PRESENT.
Read from DPCD once for all 3 values as this is an expensive operation.
Spec mentions that all of address space 02200h through 0220Fh should
contain the right information however currently only 3 values can
differ.
There is no address space in the intel_dp->dpcd struct for addresses
02200h through 0220Fh, and since so much of the data is a identical,
simply overwrite the values stored in 00000h through 0000Fh with the
values that can be overwritten from addresses 02200h through 0220Fh.
This patch helps with backward compatibility for devices pre DP1.3.
v2: read only dpcd values which can be affected, remove incorrect check,
split into drm include changes into separate patch, commit message,
verbose debugging statements during overwrite.
v3: white space fixes
v4: make path dependent on DPCD revision > 1.2
v5: split into function, removed DPCD rev check
v6: add debugging prints for early exit conditions
v7 (From Manasi):
* Memcpy, memcmp and debig logging based on sizeof(dpcd_ext) (Jani N)
* Exit early (Jani N)
v8 (From Manasi):
* Get rid of superfluous debug prints (Jani N)
* Print entire base DPCD before memcpy (Jani N)
v9 (From Manasi):
* Add uniform newlines (Rodrigo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129220058.19636-1-manasi.d.navare@intel.com
Always show the FEC capability as it is initialised to 0 before error.
Fixing,
drivers/gpu/drm/i915/intel_dp.c:3846 intel_dp_get_dsc_sink_cap() warn: inconsistent indenting
Fixes: 08cadae8e1 ("i915/dp/fec: Cache the FEC_CAPABLE DPCD register")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120202439.13017-2-chris@chris-wilson.co.uk
Fix the intel_link_compute_m_n in case of display stream
compression. This patch passes the compressed_bpp to
intel_link_compute_m_n if compression is enabled.
Fixes: a4a157777c ("drm/i915/dp: Compute DSC pipe config in atomic check")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201010412.32372-1-manasi.d.navare@intel.com
For DP 1.4 and above, Display Stream compression can be
enabled only if Forward Error Correctin can be performed.
Add a crtc state for FEC. Currently, the state
is determined by platform, DP and DSC being
enabled. Moving forward we can use the state
to have error correction on other scenarios too
if needed.
v2:
- Control compression_enable with the fec_enable
parameter in crtc state and with intel_dp_supports_fec()
(Ville)
- intel_dp_can_fec()/intel_dp_supports_fec()(manasi)
v3: Check for FEC support along with setting crtc state.
v4: add checks to intel_dp_source_supports_dsc.(manasi)
- Move intel_dp_supports_fec() closer to
intel_dp_supports_dsc() (Anusha)
v5: Move fec check to intel_dp_supports_dsc(Ville)
v6: Remove warning. rebase.
v7: change crtc state to include DP sink and fec capability
of source.(Manasi)
v8: Set fec_enable in crtc in intel_dp_compute_config().
v9 (From Manasi):
* Combine the !edp and !fec_support check
* Derive dev_priv from intel_dp directly
v10 (From Manasi):
* Rebase
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.comk>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-14-manasi.d.navare@intel.com
This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.
v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-6-manasi.d.navare@intel.com
This patches does the following:
1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific
This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.
v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks
v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)
v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)
Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers
v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129193827.7914-1-manasi.d.navare@intel.com
DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.
v15:
* Rebase over drm-tip
v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)
v7:
* Fix indentation in compute_m_n (Manasi)
v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)
v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)
v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)
v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)
v2:
* Add if-else for eDP/DP (Gaurav)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128213621.21391-1-manasi.d.navare@intel.com
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
intel_dp_detect() caches the aux_domain in the beginning of the
function as it is used twice, so lets also use it as the aux_domain
don't change in runtime.
v3: returning intel_dp_retrain_link() error insted of
connector_status_disconnected
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107235449.32264-1-jose.souza@intel.com
The MG DP mode needs to be configured for Type C static/fixed/legacy
HDMI ports too, the same way as it's configured for Type C
static/fixed/legacy, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-3-imre.deak@intel.com
The MG PHY clock gating needs to be configured for Type C
static/fixed/legacy HDMI ports the same way it's configured for Type C
static/fixed/legacy and aternate mode DP ports, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-2-imre.deak@intel.com
Similar to DSC DPCD registers, let us cache
FEC_CAPABLE register to avoid using stale
values. With this we can avoid aux reads
everytime and instead read the cached values.
v2: Avoid using memset and array for a single
field. (Manasi,Jani)
v3: Print FEC CAPABILITY value. (Manasi)
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102041455.15818-1-anusha.srivatsa@intel.com
Use the newly added "max bpc" connector property to limit pipe bpp.
V3: Use drm_connector_state to access the "max bpc" property
V4: Initialize the drm property, add suuport to DP(Ville)
V5: Use the property in the connector and fix CI failure(Ville)
V6: Use the core function to attach max_bpc property, remove the redundant
clamping of pipe bpp based on connector info
V7: Fix Checkpatch warnings
V9: Cleanup connected_sink_max_bpp and fix initial value in DP(Ville)
V12: Fix debug message(Ville)
V13: Remove the redundant check and simplify the check logic(Stan)
V14: Fix the check in connected_sink_max_bpp(Stan)
v15 (From Manasi): Add missing break (Stan)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kishore Kadiyala <kishore.kadiyala@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023014400.16055-1-manasi.d.navare@intel.com
From ICL onwards the AUX power domain may change dynamically based on
whether a DDI/TypeC port is in thunderbolt or non-thunderbolt mode, so
use a helper function instead of a static field to get the current
domain.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-5-imre.deak@intel.com
From ICL onwards DDI/TypeC ports - even in HDMI static mode - need to know
which AUX CH belongs to them, so initialize aux_ch for those ports too.
For consistency do this for all HDMI ports, not only for DDI/TypeC ones.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-4-imre.deak@intel.com
From ICL onwards all DDI/TypeC ports - even working in HDMI mode - need
to know their corresponding AUX CH, so move the field to a common
struct.
No functional change.
v3:
- Add code comment about which ports aux_ch is used for. (Jose)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-3-imre.deak@intel.com
From ICL onwards all the DDI/TypeC ports - even working in HDMI mode -
need to know their corresponding AUX channel, so move the corresponding
helper to a common place.
No functional change.
v4:
- Fix 'no space is necessary after a cast' checkpatch warn.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-2-imre.deak@intel.com
Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-3-jose.souza@intel.com
Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.
Also setting it to unknown will earlier return
icl_tc_phy_disconnect() for any future calls to
intel_digital_port_connected(), this way we don't need to check if
port is marked as safe everytime.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-2-jose.souza@intel.com
When DSC is supported we need to validate the modes based on the
maximum supported compressed BPP and maximum supported slice count.
This allows us to allow the modes with pixel clock greater than the
available link BW as long as it meets the compressed BPP
and slice count requirements.
v3:
* Use the macro for dsc sink support (Jani N)
v2:
* Properly comment why we are right shifting the bpp value (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-6-manasi.d.navare@intel.com
This patch adds helpers for calculating the maximum compressed BPP
supported with small joiner.
This also adds a helper for calculating the slice count in case
of small joiner.
These are inside intel_dp since they take into account hardware
limitations.
v6:
* Take mode_clock and mode_hdisplay as input arguments
so that this can be called in intel_dp_mode_valid (Manasi)
v5:
* Get the max slice width from DPCD
* Check against Min_Slice_width of 2560 (Anusha)
v4:
* #defines for PPR in slice count helper (Gaurav)
v3:
* Simply logic for bpp (DK)
* Limit the valid slice count by max supported by Sink (Manasi)
v2:
* Change the small joiner RAM buffer constant as bspec changed (Manasi)
* rename it as SMALL_JOINER since we are not enabling
big joiner yet (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-5-manasi.d.navare@intel.com
DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting
GEN 11.
This patch implements the discovery phase of DSC. On hotplug,
source reads the DSC DPCD register set (0x00060 - 0x0006F) to
read the decompression capabilities of the sink device.
This entire block of registers is cached in intel_dp so that
capability information can be used during DSC configuration
phase during compute_config phase of the modeset.
For eDP, this caching happens during the eDP initialization.
This caching is done only for eDP and DP rev >= 1.4
v5:
* Fix the block comment (Gaurav)
* Fix the commit message DSC DPCD addresses (Gaurav)
* Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha)
v4:
* Cache these only for Gen >= 11
v3:
* Remove the dsc_sink_support field in intel_dp (Jani N)
v2:
* Clear the cached registers on hotplug always (Jani N)
* Combine the eDP and DP caching in same function (Jani N)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-3-manasi.d.navare@intel.com
When a HDCP authentication is in progress, if the display sink is
hot unplugged, all DDC/AUX transaction related to the HDCP
authentication will fail.
This patch moves those kind of HDCP DDC/AUX failures into the debug
logs instead of errors.
v2:
Bksv invalid state is provided as debug msg
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540291288-22185-1-git-send-email-ramalingam.c@intel.com
HDCP check link is invoked only on CP_IRQ detection, instead of all
short pulses.
v3:
No Changes.
v4:
Added sean in cc and collected the reviewed-by received.
v5:
No Change.
v6:
No Change.
v7:
No Change.
v8:
Rebased.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540286550-20399-3-git-send-email-ramalingam.c@intel.com
Just sorting this "if" block from newer to older platform.
The main difference here is the addition of a
missing case with return false that should never occur.
And if it occurs it is better than to raise a warn
than use the icl one.
The gen >= 11 was already present in the previous logic,
although hidden.
So, in summary no real functional change.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022171526.15641-3-rodrigo.vivi@intel.com
Since when it was introduced we forgot to add
this case so ICL was using a wrong signal_levels
as reference.
Fixes: fb5c8e9d43 ("drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017215652.26841-1-rodrigo.vivi@intel.com
Another user of crtc->config gone. The functions it calls also
needed crtc->config, so convert those as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Still pass m_n struct to intel_pch_transcoder_set_m_n (Ville)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011100457.8776-3-maarten.lankhorst@linux.intel.com
LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
This patch adds an enum "intel_output_format" to represent
the output format of a particular CRTC. This enum will be
used to produce a RGB/YCBCR4:4:4/YCBCR4:2:0 output format
during the atomic modeset calculations.
V5:
- Created this separate patch to introduce and init output_format.
- Initialize parameters of output_format_str respectively (Jani N).
- Call it intel_output_format than crtc_output_format(Ville).
- Set output format in pipe_config for every encoder (Ville).
- Get rid of extra DRM_DEBUG_KMS during get_pipe_config (Ville)
V6: Rebase
V7: Fixed alignment warnings (checkpatch)
V8: Another check[atch warning for alignment
V9: Rebase
V10: Rebase on top of DSI restructure
V11: Addressed review comment from Ville
- Set CRTC format for pre-HSW get_pipe_config() function too.
Added Ville's R-B
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-1-git-send-email-shashank.sharma@intel.com
This patch fixes the original commit c0cfb10d9e ("drm/i915/edp:
Do not do link training fallback or prune modes on EDP") that causes
a blank screen in case of certain eDP panels (Eg: seen on Dell XPS13 9350)
where first link training fails and a retraining is required by falling
back to lower link rate/lane count.
In case of some panels they advertise higher link rate/lane count
than whats required for supporting the panel's native mode.
But we always link train at highest link rate/lane count for eDP
and if that fails we can still fallback to lower link rate/lane count
as long as the fallback link BW still fits the native mode to avoid
pruning the panel's native mode yet retraining at fallback values
to recover from a blank screen.
v3:
* Add const for fixed_mode (Ville)
v2:
* Send uevent if link failure on eDP unconditionally
Fixes: c0cfb10d9e ("drm/i915/edp: Do not do link training fallback or prune modes on EDP")
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107489
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105338
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Alexander Wilson <alexander.wilson@ncf.edu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009212804.702-1-manasi.d.navare@intel.com
Almost all of the connector destroy functions do the same thing. The
differences are in the edid, detect_edid and panel cleanups, but those
are safely NULL when not initialized. Roll out a common connector
destroy hook.
Inspired by commit bc3213c444 ("drm/i915: Drop the eDP check from
intel_dp_connector_destroy()").
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009141103.20387-1-jani.nikula@intel.com
As long as the connector was zeroed during allocation calling
intel_panel_fini() is safe even if we haven't initialized
the panel struct explicitly. So let's drop the useless eDP
check from dp connector destruction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181008134641.24868-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003184210.1306-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
We've opted to use the maximum link rate and lane count for eDP panels,
because typically the maximum supported configuration reported by the
panel has matched the native resolution requirements of the panel, and
optimizing the link has lead to problems.
With eDP 1.4 rate select method and DSC features, this is decreasingly
the case. There's a need to optimize the link parameters. Moreover,
already eDP 1.3 states fast link with fewer lanes is preferred over the
wide and slow. (Wide and slow should still be more reliable for longer
cable lengths.)
Additionally, there have been reports of panels failing on arbitrary
link configurations, although arguably all configurations they claim to
support should work.
Optimize eDP 1.4+ link config fast and narrow.
Side note: The implementation has a near duplicate of the link config
function, with just the two inner for loops turned inside out. Perhaps
there'd be a way to make this, say, more table driven to reduce the
duplication, but seems like that would lead to duplication in the table
generation. We'll also have to see how the link config optimization for
DSC turns out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105267
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905095321.13843-1-jani.nikula@intel.com
There are two copies of the same code called from long and short
pulse handlers.
v2: Rebase due to s/int status/enum drm_connector_status in
intel_dp_detect()
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-6-dhinakaran.pandiyan@intel.com
The intel_dp->detect_done flag is no more useful. Pull
intel_dp_long_pulse() into the lone caller,
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-5-dhinakaran.pandiyan@intel.com
A crtc modeset lock was added for link retraining but
intel_dp_retrain_link() knows to take the necessary locks since
commit c85d200e83 ("drm/i915: Move SST DP link retraining into the
->post_hotplug() hook")
v2: Drop AUX power domain reference in the early return path
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-4-dhinakaran.pandiyan@intel.com
We have two cases of intel_dp to intel_encoder conversions, use a
local variable to store the conversion.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-3-dhinakaran.pandiyan@intel.com
Commit '3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check,
unconditionally during long pulse"")' applies a work around for sinks
that don't signal link loss. The work around does not need to have to be
that broad as the issue was seen with only one particular monitor; limit
this only for external displays as eDP features like PSR turn off the link
and the driver ends up retraining the link seeeing that link is not
synchronized.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-2-dhinakaran.pandiyan@intel.com
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
So far we have only been calling
drm_connector_init_panel_orientation_property(), which checks for
panel orientation quirks in the drm_panel_orientation_quirks.c file,
for DSI panels as so far only devices with DSI panels have had panels
which are not mounted up right.
The new GPD win2 device uses a portrait screen in a landscape case,
so now we've a device with an eDP panel which needs the panel-orientation
property to let the fbcon code and userspace know that the image needs to
be fixed-up.
This commit makes intel_edp_init_connector() call
drm_connector_init_panel_orientation_property() so that the property
gets added.
Reported-and-tested-by: russianneuromancer@ya.ru
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180909133457.10636-2-hdegoede@redhat.com
UAPI Changes:
- None
Cross-subsystem Changes:
- None
Core Changes:
- Allow drivers to disable features with per-device granularity (Ville)
- Use EOPNOTSUPP when iface/feature is unsupported instead of
EINVAL/errno soup (Chris)
- Simplify M/N DP quirk by using constant N to limit size of M/N (Shawn)
- add quirk for LG LP140WF6-SPM1 eDP panel (Shawn)
Driver Changes:
- i915/amdgpu: Disable DRIVER_ATOMIC for older/unsupported devices (Ville)
- sun4i: add support for R40 HDMI PHY (Icenowy)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAluiqZAACgkQlvcN/ahK
BwrD7gf+O9hI1+sWAKs9/D2xz5G0Ap/wTUtPZprVx+UMg833T4E3q5esSTvlKd5q
QdijWWFZ3Eu7osQB5QTvCHpJ1F1Q9DScYdD5rd0WRhZBGnBd2guFziFRhleXpQH1
CTo/xjS4Y1l1wEildvZdjPaDfXE0Q+uK8kl11AIVoYQvW6V28/pwCW+mmfMfQG4D
lC9Lj5iPTDGLmbT3DZcH9ZUU8CZreJVPDn+mi8XsAOGt55YlCphl5XsOabNRzpCh
5VYZbauJqrlfa3/cbVuFpTqjqR5XRlMvzgdYH2Wa+9JreiReNCDs3CVL4YnLWe0p
PIfE6ZC2ucX831aZOodV7KtwtLYc/Q==
=oPPq
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-09-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.20:
UAPI Changes:
- None
Cross-subsystem Changes:
- None
Core Changes:
- Allow drivers to disable features with per-device granularity (Ville)
- Use EOPNOTSUPP when iface/feature is unsupported instead of
EINVAL/errno soup (Chris)
- Simplify M/N DP quirk by using constant N to limit size of M/N (Shawn)
- add quirk for LG LP140WF6-SPM1 eDP panel (Shawn)
Driver Changes:
- i915/amdgpu: Disable DRIVER_ATOMIC for older/unsupported devices (Ville)
- sun4i: add support for R40 HDMI PHY (Icenowy)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919200218.GA186644@art_vandelay
Some DP dongles in particular seem to be fussy about too large
link M/N values. Set specific value for N divider can resolve
this issue per dongle vendor's comment. So configure N as
constant value (0x8000) to instead of reduce M/N formula when
specific DP dongle connected.
v2: add more comments for issue description and fix typo.
v3: add lost commit messages back for version 2
v4: send patch to both intel-gfx and dri-devel
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1536733371-25004-3-git-send-email-shawn.c.lee@intel.com
