An earlier patch was added to reserve space in the ring buffer for the
commands issued during 'add_request()'. The initial version was
pessimistic in the way it handled buffer wrapping and would cause
premature wraps and thus waste ring space.
This patch updates the code to better handle the wrap case. It no
longer enforces that the space being asked for and the reserved space
are a single contiguous block. Instead, it allows the reserve to be on
the far end of a wrap operation. It still guarantees that the space is
available so when the wrap occurs, no wait will happen. Thus the wrap
cannot fail which is the whole point of the exercise.
Also fixed a merge failure with some comments from the original patch.
v2: Incorporated suggestion by David Gordon to move the wrap code
inside the prepare function and thus allow a single combined
wait_for_space() call rather than doing one before the wrap and
another after. This also makes the prepare code much simpler and
easier to follow.
v3: Fix for 'effective_size' vs 'size' during ring buffer remainder
calculations (spotted by Tomas Elf).
For: VIZ-5115
CC: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the purpose of state checking we only care about the DPLL HW flags
that we actually program, so mask off the ones that we don't.
This fixes one set of DPLL state check failures.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.
This fixes the state checker failures I saw on my BXT with HDMI output.
v2:
- rebased on v2 of patch 4/5
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.
This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.
While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the helper next to the PLL helpers of the other platforms for
clarity.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hardware supposedly ignores the WM1 watermarks while the PND
deadline mode is enabled, but clear out the register just in case.
This is what the other OS does, and it does make register dumps look
more consistent when we don't have partial WM1 values lingering in
the registers (some WM1 watermarks already get zeroed when the actually
used DSPFW registers get written).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow tweaking the VLV/CHV memory latencies thorugh sysfs, like we do
for ILK+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabling PM5/DDR DVFS with multiple active pipes isn't a validated
configuration. It does seem to work most of the time at least, but
there is clearly an additional risk of underruns, so let's not play
with fire.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to get decnet memory self refresh residency on VLV, flip it
over to the new CHV way of doing things. VLV doesn't do PM5 or DDR DVFS
so it's a bit simpler.
I'm not sure the currently memory latency used for CHV is really
appropriate for VLV. Some further testing will probably be needed to
figure that out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Consider which planes are active and compute the FIFO split based on the
relative data rates. Since we only consider the pipe src width rather
than the plane width when computing watermarks it seems best to do the
same when computing the FIFO split as well. This means the only thing we
actually have to consider for the FIFO splut is the bpp, and we can
ignore the rest.
I've just stuffed the logic into the watermark code for now. Eventually
it'll need to move into the atomic update for the crtc.
There's also one extra complication I've not yet considered; Some of the
DSPARB registers contain bits related to multiple pipes. The registers
are double buffered but apparently they update on the vblank of any
active pipe. So doing the FIFO reconfiguration properly when multiple
pipes are active is not going to be fun. But let's ignore that mess for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want cxsr exit to happen ASAP, so toss in some POSTING_READ()s to
make sure things are really kicked off.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can't elide the fb tracking invalidate if the buffer is already in
the right domain since that would lead to missed screen updates. I'm
pretty sure I've written this already before but must have gotten lost
unfortunately :(
v2: Chris observed that all internal set_domain users already
correctly do the fb invalidate on their own, hence we can move this
just into the set_domain ioctl instead.
v3: I screwed up setting the invalidate ORIGIN_* correctly (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can't improve a 0 deviation, so when we find such a divider, skip the
remaining ones they won't be better.
This short-circuit the search for 34 of the 373 test frequencies in the
corresponding i-g-t test (tools/skl_compute_wrpll)
v2: Place the short-circuiting code in skl_compute_wrpll() (Paulo)
(I'm sure nobody will notice the spurious removal of a blank line)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broxton is using a different register and different bit ordering
for rps status capabilities.
Also GT perf freqency register is different for Broxton so update
that.
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, if an odd divider improves the deviation (minimizes it), we
take that divider. The recommendation is to prefer even dividers.
v2: Move the check at the right place after having inverted the two for
loops in the previous patch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HW validation team came back from further testing with a slightly
changed constraint on the deviation between the DCO frequency and the
central frequency. Instead of +-4%, it's now +1%/-6%.
Unfortunately, the previous algorithm didn't quite cope with these new
constraints, the reason being that it wasn't thorough enough looking at
the possible divider candidates.
The new algorithm looks at all dividers, which is definitely a hammer
approach (we could reduce further the set of dividers to good ones as a
follow up, at the cost of a bit more complicated code). But, at least,
we can now satisfy the +1%/+6% rule for all the "Well known" HDMI
frequencies of my test set (373 entries).
On that subject, the new code is quite extensively tested in
intel-gpu-tools (tools/skl_compute_wrpll).
v2: Fix cycling between central frequencies and dividers (Paulo)
Properly choose the minimal deviation between postive and negative
candidates (Paulo).
On the 373 test frequencies, v2 computes better dividers than v1 (ie
more even dividers and lower deviation on average):
v1: average deviation: 206.52
v2: average deviation: 194.47
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After Mika's ppgtt cleanup series, all the other free functions have
drm_device as the first parameter, except this one.
No functional changes.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A safer way to update the PDPx registers is sending lri commands, added
in the ring before the batchbuffer start. Otherwise, the ctx must be idle
before trying to change anything (but the ring-tail) in the ctx image. An
example where the ctx won't be idle is lite-restore.
This patch depends on 5b7e4c9ce ("drm/i915/gtt: Mark TLBS dirty for gen8+").
v2: Combine lri writes (and save 8 commands). (Mika)
v3: Rebase after ring/req changes, and removed references to deprecated patches.
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need for atomicity here. Convert all bitmap
operations to nonatomic variants.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Scratch page is part of struct i915_address_space. Move other
scratch entities into the same struct. This is a preparatory patch
for having only one instance of each scratch_pt/pd.
v2: make commit msg more readable
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v1)
[danvet: Bikeshed summary to avoid confusion with vmas.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Write page directory entry without using superfluous
indirect function. Also remove unused device parameter
from the encode function.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dynamic page table allocation might wake the shrinker
when memory is requested for page table structures.
As this happens when we try to allocate the virtual address
during binding, our vma might be among the targets for eviction.
We should do i915_vma_pin() and do pin early in there like Chris
suggests but this is interim solution.
Shield our vma from shrinker by incrementing pin count before
the virtual address is allocated.
The proper place to fix this would be in gem, inside of
i915_vma_pin(). But we don't have that yet so take the short
cut as a intermediate solution.
Testcase: igt/gem_ctx_thrash
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lay out scratch page structure in similar manner than other
paging structures. This allows us to use the same tools for
setup and teardown.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make paging structure type agnostic *_px macros to access
page dma struct, the backing page and the dma address.
This makes the code less cluttered on internals of
i915_page_dma.
v2: Superfluous const -> nonconst removed
v3: Rebased
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As there is flushing involved when we have done the cpu
write, make functions for mapping for cpu space. Make macros
to map any type of paging structure.
v2: Make it clear tha flushing kunmap is only for ppgtt (Ville)
v3: Flushing fixed (Ville, Michel). Removed superfluous semicolon
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we setup page directories and tables, we point the entries
to a to the next level scratch structure. Make this generic
by introducing a fill_page_dma which maps and flushes. We also
need 32 bit variant for legacy gens.
v2: Fix flushes and handle valleyview (Ville)
v3: Now really fix flushes (Michel, Ville)
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has slipped in somewhere but it was harmless
as we check the page pointer before teardown.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the paging structures are now similar and mapped for
dma. The unmapping is taken care of by common accessors, so
don't overload the reader with such details.
v2: Be consistent with goto labels (Michel)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All our paging structures have struct page and dma address
for that page.
Add struct for page/dma address pairs and use it to make
the setup and teardown for different paging structures
identical.
Include the page directory offset also in the struct for legacy
gens. Rename it to clearly point out that it is offset into the
ggtt.
v2: Add comment about ggtt_offset (Michel)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The legacy mode mm switch and the execlist context assignment
needs dma address for the page directories.
Introduce a function that encapsulates the scratch_pd dma
fallback if no pd is found.
v2: Rebase, s/ring/req
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can have exactly 4GB sized ppgtt with 32bit system.
size_t is inadequate for this.
v2: Convert a lot more places (Daniel)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the allocation area against the known end
of address space instead of against fixed value.
v2: Return ENODEV on internal bugs (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we touch gen8+ page maps, mark them dirty like we
do with previous gens.
v2: Update comment (Joonas)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we don't have any real indication when a pipe gets
enabled/disabled. Add some.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The registers and process differ from other platforms. If the hardware
was programmed incorrectly, this will return invalid cdclk values, which
should then cause reprogramming of the hardware.
v2(Matt): Return 19.2 MHz when DE PLL is disabled (Ville)
v3: Make less assumptions about the hardware state (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently object size is returned for the rotated VMA size which can be
bigger than the rotated view itself. Since the binding code pads all
excess size with scratch pages the only minor issue with this is wasting
some GGTT space, but still feels nicer to fix and report the real size.
v2: Rebase for tracking size in bytes instead of pages.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way data is available as soon as the view is passed into the call chain.
v2: Store size in bytes instead of pages under the appropriate name. (Chris Wilson)
v3: Use uint64_t instead of size_t. (Daniel Vetter)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is only used in logging and it doesn't need to exist on its own.
Also it was misleading to log view size as object size.
v2: Improve commit message. (Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[danvet: s/%lu/%zu/ where needed, reported by 0-day.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.
I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This typo lead to the crtc scaler getting enabled incorrectly and an
evantual state checker mismatch about the scaler_id.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Indirect context w/a batch buffer,
WaClearSlmSpaceAtContextSwitch
This WA performs writes to scratch page so it must be valid, this check
is performed before initializing the batch with this WA.
v2: s/PIPE_CONTROL_FLUSH_RO_CACHES/PIPE_CONTROL_FLUSH_L3 (Ville)
v3: GTT bit in scratch address should be mbz (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
