They are similar to ICM20608 chip.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device_get_match_data for using of and acpi tables.
In spi support add missing mpu6515 and of match table.
Reorganize Kconfig to display chips grouped by generations.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Modify NPCM ADC reset support from
direct register access to reset controller support.
please make sure to modify NPCM adc device tree
parameters as described at nuvoton,npcm-adc.txt
document for using this change.
Note for anyone noting that this is a breaking change, this is on
a BMC and effectively in a close ecosystem so it is fine to rely
on DT and kernel being updated together.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is modelled after the vcnl4035 driver. For the vcnl40{0,1,2}0
we don't do anything since they use on demand measurement.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will be useful when introducing runtime pm.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These two defines are unused since the driver was introduced in commit
02b829f9e1 ("iio: dac: Add support for ltc2632 DACs").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only difference between LTC2632 and LTC2636 is that the former has
two DAC channels while the latter has eight.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channel data for ltc2632l12 and ltc2632h12 are identical. So there
is no gain in using two different (but identical) channel descriptions.
The only side effect of this change is some memory savings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add suspend and resume operations for being used by optional power
management.
The suspend function is switching off an GPIO which can be used by the
hardware to switch power off. The resume function is switching the GPIO
on and sleeps an adjustable time to give the device a chance to be up
and running.
If activated the driver gets into autosuspend after some time of
inactivity.
Suggested-by: Franz Parzer <rpi-receiver@htl-steyr.ac.at>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A null pointer deference on pdata can occur if the allocation of
pdata fails. Fix this by adding a null pointer check and handle
the -ENOMEM failure in the caller.
Addresses-Coverity: ("Dereference null return value")
Fixes: 3ce85cc4fb ("iio: st_sensors: get platform data from device tree")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the LOW_PASS_FILTER_3DB_FREQUENCY attribute
in iio_chan_spec for each channel. The used filters are sinc3
or sinc4. The filter type with the highest output data rate
is used when setting a low pass frequency in the channel's sysfs.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a spelling mistake and grammar mistake in a dev_err
message. Fix it.
Also include Joe Perches' additional suggestions around:
* Missing newlines
* Excess braces
* Odd indentation
* Some grammar
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Suggested-by: Joe Perches <joe@perches.com> # Additional cleanups etc.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver handles two different Sharp sensors that have been
proposed for merging to the mainline kernel over the years, and
already has a limited proximity-only driver in the input
subsystem.
These components are completely different from the confusingly
similarly named Sharp GP2AP020A00F, for which we have a driver
in drivers/iio/light/gp2ap020a00f.c
The two components GP2AP002A00F and GP2AP002S00F are
distinctively different but similar: they share the same set of
registers but differ slightly in the I2C protocol.
Instead of the approach by the previous input driver, we create
a combined IIO proximity and light sensor driver.
The plan is to merge this driver and delete the input driver.
The pieces for the driver are picked all over the place after
researching and grepping through a few different vendor trees
and driver submissions.
We merge it under the light sensors because:
- It has similarities with the Capella CM3605 light sensor and
proximity driver which is there.
- It is related to the GP2AP020A00F driver which is also there.
This driver was tested with the Samsung GT-S7710 mobile phone
which has the GP2AP002S00F proximity sensor mounted.
The suspend/resume cycle will disable the interrupt from the
sensor. If someone would desire to use this interrupt for
wakeup, the driver will need modifications.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Jonathan Bakker <xc-racer2@live.ca>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
odr to odr_table
gain to fs_table
'gain' is actually in 'st_lsm6dsx_fs' structure of 'fs_table'
Signed-off-by: JieunKim <jieun.kim4758@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use st_sensors_dev_name_probe() instead open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
Use devm_reset_control_get_optional_exclusive() instead of
devm_reset_control_get_exclusive() as reset controller is optional.
Nevertheless if reset controller is expected but reports an
error, propagate the error code to the caller. In such case
a nice error trace is emitted unless we're deferring the probe
operation.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change removes the reset controller reference from the local
DAC instance since it is used only at probe time.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Hardware could be physically mounted in any possible direction and
userpspace needs to be aware of the mounting orientation in order to
process sensor's data correctly. In particular this helps iio-sensor-proxy
to report display's orientation properly on a phone/tablet devices.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow to read the mount-matrix device tree property and provide the
mount_matrix file for userspace to read.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not print an error trace when deferring probe for some resource.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16490 is part of the same family with ADIS16495 and ADIS16497,
the main difference is the temperature, accelerometer and gyroscope
scales.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16490.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This puts an upper bound on "val2" but it also needs to have a lower
bound (BMA400_SCALE_MIN).
Fixes: 465c811f1f ("iio: accel: Add driver for the BMA400")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make mpu6050 usable on platforms which provide only any-edge interrupts.
One example of this kind of platform is AT91SAM9G45
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of temperature data in fifo for all chips.
Enable unification of scan elements for icm20602.
Add macros for generating scan elements.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert to use device_get_match_data() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since IIO framework supports device property API and driver has been moved
already to the use of GPIO descriptors the logical continuation is to
get rid of platform data completely. We are on the safe side here since
there are no users of it in the kernel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7124 data-sheet specifies that the falling edge
of the DOUT line should be used for an interrupt.
The current irq flag (IRQF_TRIGGER_LOW) used will
cause unwanted behaviour. When enabling the interrupt
it will fire once because the DOUT line is already low.
This will make the driver to read an unfinished conversion
from the chip.
This patch sets the irq type to the one specified in
the data-sheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current `delay_usecs`
with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update sampling rate when oversampling ratio is changed
through the IIO ABI.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Apply data formatting to single conversion,
as this is already done in continuous and trigger modes.
Fixes: 102afde629 ("iio: adc: stm32-dfsdm: manage data resolution in trigger mode")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Cc: <Stable@vger.kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we have access to the struct device_driver and thus to the ID table,
there is no need to supply special parameters to st_sensors_of_name_probe().
Besides that we have a common API to get driver match data, there is
no need to do matching separately for OF and ACPI.
Taking into consideration above, simplify the ST sensors code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit 41c128cb25 ("iio: st_gyro: Add lsm9ds0-gyro support")
assumes that gyro in LSM9DS0 is the same as others with 0xd4 WAI ID,
but datasheet tells slight different story, i.e. the first scale factor
for the chip is 245 dps, and not 250 dps.
Correct this by introducing a separate settings for LSM9DS0.
Fixes: 41c128cb25 ("iio: st_gyro: Add lsm9ds0-gyro support")
Depends-on: 45a4e4220b ("iio: gyro: st_gyro: fix L3GD20H support")
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing return value check in st_lsm6dsx_read_oneshot disabling the
sensor. The issue is reported by coverity with the following error:
Unchecked return value:
If the function returns an error value, the error value may be mistaken
for a normal value.
Addresses-Coverity-ID: 1446733 ("Unchecked return value")
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the data sheet the ambient sensor's scale is 0.12 lux/step
(not 0.024 lux/step as used by vcnl4200) when the integration time is
80ms. The integration time is currently hardcoded in the driver to that
value.
See p. 8 in https://www.vishay.com/docs/84307/designingvcnl4040.pdf
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous versions of `iio_compute_scan_bytes` only aligned each element
to its own length (i.e. its own natural alignment). Because multiple
consecutive sets of scan elements are buffered this does not work in
case the computed scan bytes do not align with the natural alignment of
the first scan element in the set.
This commit fixes this by aligning the scan bytes to the natural
alignment of the largest scan element in the set.
Fixes: 959d2952d1 ("staging:iio: make iio_sw_buffer_preenable much more general.")
Signed-off-by: Lars Möllendorf <lars.moellendorf@plating.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO triggered buffer depends on IIO buffer which is missing from Kconfig
file. This should go unnoticed most of the time because there's a
chance something else has already enabled buffers. In some rare cases
though one might experience kbuild warnings about unmet direct
dependencies and build failures due to missing symbols.
Fix this by selecting IIO_BUFFER explicitly.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, attempting to probe a device with ST_LSM6DS3_ID
(e.g. using the st,lsm6ds3 compatible) fails with:
st_lsm6dsx_i2c 1-006b: unsupported whoami [69]
... even though 0x69 is the whoami listed for ST_LSM6DS3_ID.
This happens because st_lsm6dsx_check_whoami() also attempts
to match unspecified (zero-initialized) entries in the "id" array.
ST_LSM6DS3_ID = 0 will therefore match any entry in
st_lsm6dsx_sensor_settings (here: the first), because none of them
actually have all 12 entries listed in the "id" array.
Avoid this by additionally checking if "name" is set,
which is only set for valid entries in the "id" array.
Note: Although the problem was introduced earlier it did not surface until
commit 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
because ST_LSM6DS3_ID was the first entry in st_lsm6dsx_sensor_settings.
Fixes: d068e4a0f9 ("iio: imu: st_lsm6dsx: add support to multiple devices with the same settings")
Cc: <stable@vger.kernel.org> # 5.4
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes device tree channel configuration.
ad7124 driver reads channels configuration from the device tree.
It expects to find channel specifications as child nodes.
Before this patch ad7124 driver assumed that the child nodes are parsed
by for_each_available_child_of_node in the order 0,1,2,3...
This is wrong and the real order of the children can be seen by running:
dtc -I fs /sys/firmware/devicetree/base on the machine.
For example, running this on an rpi 3B+ yields the real
children order: 4,2,0,7,5,3,1,6
Before this patch the driver assigned the channel configuration
like this:
- 0 <- 4
- 1 <- 2
- 2 <- 0
........
For example, the symptoms can be observed by connecting the 4th channel
to a 1V tension and then reading the in_voltage0-voltage19_raw sysfs
(multiplied of course by the scale) one would see that channel 0
measures 1V and channel 4 measures only noise.
Now the driver uses the reg property of each child in order to
correctly identify to which channel the parsed configuration
belongs to.
Fixes b3af341bbd: ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function to detect the number of channels to output
in trigger handler. This is based on IIO_TIMESTAMP channel being the
delimiter between input and output channels.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DHT11 isn't addressable and will trigger temperature measurement on any
data sent on the bus.
Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All timeouts are now handled by a dedicated timeout struct. This
variable is no longer needed.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis library only allows to define a `startup_delay` which for some
devices is enough. However, other devices define different timeouts with
significantly different timings which could lead to devices to not wait
enough time or to wait a lot more than necessary (which is not
efficient). This patch introduces a new timeout struct that must be
passed into `adis_init()`. There are mainly, for now, three timeouts
used. This is also an introductory patch with the goal of refactoring
`adis_initial_startup()`. New driver's (eg: adis16480, adis16460) are
replicating code for the device initial setup. With some changes (being
this the first one) we can pass this to `adis_initial_startup()`.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
The dma_request_chan() is the standard API to request slave channel,
clients should be moved away from the legacy API to allow us to retire
them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
-----BEGIN PGP SIGNATURE-----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=8FmM
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This adds support for the BMA254 variant of this
accelerometer. The only difference for the simple IIO
driver is that values are 12 bit and the temperature
offset differs by 1 degree.
Whilst wildcards in naming are normally frowned upon:
The cases where I have labeled variables "25x" is where the
models are identical, so as to make things easier for people
that want to add support for BMA253 and BMA255.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to limit the driver use by OF/platform code.
In this case we simple remove redundant OF parts from the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no evidence of officially registered ACPI IDs for these devices.
Thus, revert ACPI support from the driver. All authors of the respective
changes are being informed here:
d5c94568cc ("iio: add bmp280 pressure and temperature driver")
6dba72eca7 ("iio: pressure: bmp280: add support for BMP180")
14beaa8f5a ("iio: pressure: bmp280: add humidity support")
Above seems a cargo cult without paying attention to how ACPI IDs
are being allocated.
Cc: Vlad Dogaru <ddvlad@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is implied that 'read' will read the first n bytes and not e.g. bytes
only from offsets within the buffer that are a prime number.
This change is non-functional, mostly just a rename.
A secondary intent with this patch is to make room later to add a write
callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dmaengine buffer has some length alignment requirements that can differ
from platform to platform. If the length alignment requirements are not met
unexpected behavior like dropping of samples can occur.
Currently these requirements are not reported and applications need to know
the requirements of the platform by some out-of-band means.
Add a new buffer attribute that reports the length alignment requirements
called `length_align_bytes`. The reported length alignment is in bytes that
means the buffer length alignment in sample sets depends on the number of
enabled channels and the bytes per channel. Applications using this
attribute to determine the buffer size requirements need to consider this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All Sensors DLH is series of low voltage digital pressure sensors.
Additionally to pressure value sensors deliver a temperature value.
Sensors can be accessed over I2C and SPI, this driver supports
only I2C access.
Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make sure that the industrialio-buffer-dmaengine has proper license
information so it can be build as a module and loaded without tainting the
kernel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This uses the C99 explicit .member assignment for the
variant data in struct bma180_part_info. This makes it
easier to understand and add new variants.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This brings up the VDD and VDDIO regulators using the
regulator framework. Platforms that do not use regulators
will provide stubs or dummy regulators.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Having a shorthand "dev" instead of &client->dev everywhere
makes the code easier to read (more compact).
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enabled i2c master controller support for LSM6DSM sensor. Enable
ext_sensor0 for lsm6dsm. This series has been tested using LIS2MDL as
slave device connected to the i2c controller of the LSM6DSM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename st_lsm6dsx_shub_read_reg routine in st_lsm6dsx_shub_read_output
since it is used to read from sensorhub channel0 output register
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the sensor hub output register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the pull up register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if the master enable register is located in the primary or in the
secondary memory page. This is a preliminary patch to support i2c master
controller on lsm6dsm devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Export max number of slave devices supported by the i2c master
controller in st_lsm6dsx_shub_settings data structure.
This is a preliminary patch to support i2c master controller
on lsm6dsm sensors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the orginal scope of the driver was to only support
the pH product from Atlas it has evolved to other sensors.
Rename the file, driver name, and regmap to atlas-sensor which
reflects this, although keep CONFIG_ATLAS_PH_SENSOR to not cause
regressions with current configurations.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Kernel documentation script complains that some of the function parameters
are not described:
.../common/st_sensors/st_sensors_trigger.c:29: warning: Function parameter or member 'indio_dev' not described in 'st_sensors_new_samples_available'
.../common/st_sensors/st_sensors_trigger.c:29: warning: Function parameter or member 'sdata' not described in 'st_sensors_new_samples_available'
Describe function parameters where it's appropriate.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark default_press_pdata with __maybe_unused to calm a compiler down:
In file included from drivers/iio/pressure/st_pressure_spi.c:18:
drivers/iio/pressure/st_pressure.h:40:46: warning: ‘default_press_pdata’ defined but not used [-Wunused-const-variable=]
40 | static const struct st_sensors_platform_data default_press_pdata = {
| ^~~~~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark default_accel_pdata with __maybe_unused to calm a compiler down:
In file included from drivers/iio/accel/st_accel_i2c.c:19:
drivers/iio/accel/st_accel.h:67:46: warning: ‘default_accel_pdata’ defined but not used [-Wunused-const-variable=]
67 | static const struct st_sensors_platform_data default_accel_pdata = {
| ^~~~~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark gyro_pdata with __maybe_unused to calm a compiler down:
In file included from drivers/iio/gyro/st_gyro_i2c.c:18:
drivers/iio/gyro/st_gyro.h:31:46: warning: ‘gyro_pdata’ defined but not used [-Wunused-const-variable=]
31 | static const struct st_sensors_platform_data gyro_pdata = {
| ^~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI_PTR() takes care of the argument in case of !CONFIG_ACPI.
Remove unnecessary #else branch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI_PTR() takes care of the argument in case of !CONFIG_ACPI.
Remove unnecessary #else branch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no evidence that the driver supports or needs ACPI APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to have OF guard against ID table.
Drop it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark predefined constants with __maybe_unused to calm a compiler down:
In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c:17:
.../st_lsm6dsx/st_lsm6dsx.h:399:28: warning: ‘st_lsm6dsx_available_scan_masks’ defined but not used [-Wunused-const-variable=]
399 | static const unsigned long st_lsm6dsx_available_scan_masks[] = {0x7, 0x0};
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../st_lsm6dsx/st_lsm6dsx.h:392:36: warning: ‘st_lsm6dsx_event’ defined but not used [-Wunused-const-variable=]
392 | static const struct iio_event_spec st_lsm6dsx_event = {
| ^~~~~~~~~~~~~~~~
...
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7928 is software compatible with the ad7923.
The ad7908 and ad7918 are the 8 and 10-bit versions of the ad7928.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Accomplish device tree compatibility to driver AD7923
by adding of_device_id table and making a subsequent call to
MODULE_DEVICE_TABLE.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+static int ad7923_scan_direct(struct ad7923_state *st, unsigned ch)
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Removes the unused define AD7923_CHANNEL_x from the code.
Signed-off-by: Daniel Junho <djunho@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the VDD and VDDIO regulators using the regulator
framework.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a IIO driver for the Bosch BMA400 3-axes ultra-low power accelerometer.
The driver supports reading from the acceleration and temperature
registers. The driver also supports reading and configuring the output data
rate, oversampling ratio, and scale.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This chip is similar to the LTC2497 ADC, it just uses SPI instead of I2C
and so has a slightly different protocol. Only the actual hardware
access is different. The spi protocol is different enough to not be able
to map the differences via a regmap.
Also generalize the entry in MAINTAINER to cover the newly introduced
file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This allows to share most of this driver for the ltc2496 driver added in
the next commit that is an SPI variant of the ltc2497. Initially I named
the generic part ltc249x, but wild card names are frowned upon, so the
generic part is called ltc2497-core even though it's not obvious that
this is then to be reused for the ltc2496 driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Platform data is a legacy interface to supply device properties
to the driver. In this case we even don't have in-kernel users
for it. Just remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move some register definitions to hts221_avg_list, hts221_avg_list and
hts221_channels since they are used only there and simplify driver code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable overrun interrupt on STM32 ADC. In case data register hasn't been
read (by CPU or DMA), overrun condition is detected when there's new
conversion data available. Stop grabbing data and log an error message.
Use a threaded irq to avoid printing the error message from hard irq
context.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These three GPIO lines used by the Samsung sensor hub is pretty
straight-forward to convert to use GPIO descriptors.
Cc: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> yet fails to use symbols
from any the header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7266 have no in-tree users making use of the platform
data mechanism to pass address GPIO lines when not using
a fixed address, so we can easily convert this to use
GPIO descriptors instead of the platform data integers
currently passed.
Lowercase the labels "ad0".."ad2" as this will make a better
fit for platform descriptions like device tree that prefer
lowercase names such as "ad0-gpios" rather than "AD0-gpios".
Board files and other static users of this device can pass
the same GPIO descriptors using machine descriptor
tables if need be.
Cc: Alison Schofield <amsfield22@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses all the modern GPIO APIs from
<linux/gpio/driver.h> and <linux/gpio/consumer.h> so
just drop the unused legacy header <linux/gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock detect GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver is using the GPIO descriptor API but yet includes
the legacy <linux/gpio.h> header for no reason. Drop the
surplus include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warning:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The end-of-conversion (EOC) GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device is always in a low-power state due to the hardware design. It
wakes up upon a conversion request and goes back into the low-power
state. The pm ops are added to disable the device completely and to free
the regulator. Disbaling the device completely should be not that
notable but freeing the regulator is important. Because if it is a shared
power-rail the regulator won't be disabled during suspend-to-ram/disk
and so all devices connected to that rail keeps on.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
commit f7072198f2 ("iio: imu: Fix inv_mpu6050 dependencies")
undid the explicit selection of I2C_MUX previously
done by the driver, because I2C_MUX implicitly depended
on HAS_IOMEM.
However commit 93d710a65e ("i2c: mux: fix up dependencies")
cleared up the situation properly and drivers that need
to select I2C_MUX can now do so again.
It makes a lot of sense for a driver to select the driver
infrastructure it needs so restore the natural order of
things.
Cc: Richard Weinberger <richard@nod.at>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channels specification assignment in chip info was simplified.
This patch makes supporting other devices by this driver easier.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
-----BEGIN PGP SIGNATURE-----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=vySY
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
As of commit b9ddd50911 ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each time we need to read a sample (from the sysfs interface, since the
driver supports only it) the driver writes the configuration register
with the proper settings needed to perform the said read, then it runs
another xfer to actually read the resulting value. Most notably the
configuration register is updated to set the ADC internal MUX depending by
which channel the read targets.
Unfortunately this seems not enough to ensure correct operation because
the ADC works in a pipelined-like fashion and the new configuration isn't
applied in time.
The ADC alternates two phases: acquisition and conversion. During the
acquisition phase the ADC samples the analog signal in an internal
capacitor; in the conversion phase the ADC performs the actual analog to
digital conversion of the stored voltage. Note that of course the MUX
needs to be set to the proper channel when the acquisition phase is
performed.
Once the conversion phase has been completed, the device automatically
switches back to a new acquisition; on the other hand the device switches
from acquisition to conversion on the rising edge of SPI cs signal (that
is when the xfer finishes).
Only after both two phases have been completed (with the proper settings
already written in the configuration register since the beginning) it is
possible to read the outcome from SPI bus.
With the current driver implementation, we end up in the following
situation:
_______ 1st xfer ____________ 2nd xfer ___________________
SPI cs.. \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle | val N-1 + idle ...
SPI wr.. idle | cfg N + idle | (X) + idle ...
------------------------ + -------------------- + ------------------
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1
As shown in the diagram above, the value we read in the Nth read belongs
to configuration setting N-1.
In case the configuration is not changed (config[N] == config[N-1]), then
we still get correct data, but in case the configuration changes (i.e.
switching the MUX on another channel), we get wrong data (data from the
previously selected channel).
This patch fixes this by performing one more "dummy" transfer in order to
ending up in reading the data when it's really ready, as per the following
timing diagram.
_______ 1st xfer ____________ 2nd xfer ___________ 3rd xfer ___
SPI cs.. \_________/ \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle |(val N-1)+ idle | val N + ..
SPI wr.. idle | cfg N + idle | (X) + idle | (X) + ..
------------------------ + -------------------- + ------------------- + --
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1 | ..
NOTE: in the latter case (cfg changes), the acquisition phase for the
value to be read begins after the 1st xfer, that is after the read request
has been issued on sysfs. On the other hand, if the cfg doesn't change,
then we can refer to the fist diagram assuming N == (N - 1); the
acquisition phase _begins_ before the 1st xfer (potentially a lot of time
before the read has been issued via sysfs, but it _ends_ after the 1st
xfer, that is _after_ the read has started. This should guarantee a
reasonably fresh data, which value represents the voltage that the sampled
signal has after the read start or maybe just around it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not power-off accel unconditionally if wake-up events are enabled
powering off the hw FIFO. At the same time do not power-off the accel
sensor if it is 'batched' in the hw FIFO disabling sensor events
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Track hw FIFO state introducing fifo_mask since now the accel sensor
can be enabled during suspend/resume in order to trigger the wake-up
enabling the FIFO in st_lsm6dsx_resume even if it was disabled before
the suspend. Hence we must separately track the fifo state.
Fixes: 4c997dfa69 ("iio: imu: st_lsm6dsx: add wakeup-source option")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix decimation factor and sip estimation for LSM6DSM series
(max value for decimation factor is 32).
If gyro and accel sensors are enabled at 12.5Hz and 416Hz
respectively, decimation factor lookup will fail, producing
unaligned data.
Remove unused decimator filed in st_lsm6dsx_sensor structure.
Fixes: f8710f0357 ("iio: imu: st_lsm6dsx: express odr in mHZ")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back
as percent when it should have been milli percent. This is via an
incorrect scale value being returned to userspace.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This probe function is passing the wrong size to devm_iio_device_alloc().
It is supposed to be the size of the private data. Fortunately,
sizeof(*indio_dev) is larger than sizeof(struct mrfld_adc) so it doesn't
cause a runtime problem.
Fixes: a711866273 ("iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the internal reference was selected by a channel it was not enabled.
This patch fixes that and enables it.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the read of temp using of_property_read_u32_index is reading
a u32 value into a unsigned long long. This relies on machine endianness
to work correctly, so fix this by reading a u32 value and setting temp
to this value.
Addresses-Coverity: ("Reliance on integer endianness")
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
drivers/iio/accel/st_accel_core.c:1005:44: warning:
mount_matrix_ext_info defined but not used [-Wunused-const-variable=]
Using stub helper while CONFIG_ACPI is disabled to fix it.
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.
Fixes: 2985a5d884 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* CrOS EC / MFD / IIO
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part of a
series from Gwendal to refactor sensor code between MFD, CrOS EC, iio
and input in order to add a new sensorhub driver and FIFO processing
* Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
* Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXeaqtwAKCRBzbaomhzOw
wilIAQCQ3/dpAwg2skKYYf3RBLDJeDLA1id7rNSgMOXc2aKyTAD/fCQtNhwj+Hal
W//04WWngTCQF5fkE9OCJrDwbm5eRwc=
=uOGe
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Add support for parallax ping and laser ping sensors with just one pin
for trigger and echo signal.
This driver is based on srf04. In contrast to it it's necessary to
change direction of the pin and to request the irq just for the period
when the echo is rising and falling. Because this adds a lot of cases
there is this individual driver for handling this type of sensors.
Add a new configuration variable CONFIG_PING to Kconfig and Makefile.
Julia reported an issue with failing to unlock a mutex in some error
paths.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to explicitly generate update event to update
timer master mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and iio set of patches for the 5.5-rc1 release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6lVQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFnwCgyvZ62uUyQTRey0zvNTe3I4fY9L4AnAnrz3ZC
U6ZA2+Uj3O6qhAr5frRu
=uv8S
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Drivers:
* test_power: add support for current and charge_counter
* cpcap-charger: improve charge calculation and limit default charge voltage
* ab8500: convert to IIO
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=iHhO
-----END PGP SIGNATURE-----
Merge tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
Previously, the code was using the of_read_property_bool() to check if
an external regulator was provided. However, this is redundant, as it's
more simple/direct to just ask the regulator is provided, via a
`devm_regulator_get_optional()` call.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We added a sysfs ABI for getting/setting the type of a thermocouple. This
driver supports chips that support specific fixed thermocouple types; we
cannot set it, but still we can add this sysfs attribute in RO mode to
read-back the thermocouple type.
This driver supports actually several chips:
- max6675
- max31855[k/j/n/s/t/e/r]asa family
Max6675 supports only K-type thermocouples, so we can just report that.
Each chip in max31855 family supports just one specific thermocouple type
(in the obvious way: i.e. max31855jasa supports J-type). This driver did
accept a generic SPI ID and OF compatible "max31855" which does not give
any clue about which chip is really involved (and unfortunately it seems
we have no way to detect it).
This patch introduces a new set of, more specific, SPI IDs and OF
compatible strings to better match the chip type.
The old, generic, "max31855" binding is kept for compatibility reasons, but
this patch aims to deprecate it, so, should we hit it, a warning is spit.
In such case the reported thermocouple type in sysfs is '?', because we
have no way to know.
Regarding the implementation: the thermocouple type information is stored
in the driver private data and I've kept only two maxim_thermocouple_chip
types in order to avoid a lot of duplications (seven chip types with just
a different thermocouple type).
RFT because I have no real HW to test this.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sensor support various thermocouple types (e.g. J, K, N, ...). The
driver allows to configure this parameter using a DT property.
This is useful when i.e. the thermocouple is physically tied to the sensor
and it is usually not removed, or when it is at least known in advance
which sensor will be connected to the circuit.
However, if the user can randomly connect any kind of thermocouples (i.e.
the device exposes a connector, and the user is free to connect its own
sensors), it would be more appropriate to provide a mechanism to
dynamically switch from one thermocouple type to another. This can be i.e.
handled in userspace by a GUI, a configuration file or a program that
detects the thermocouple type by reading a GPIO, or a eeprom on the probe,
or whatever.
This patch adds a IIO attribute that can be used to override, at run-time,
the DT-provided setting (which serves as default).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We have a couple of thermocouple IIO drivers, supporting several chips.
Some of them support only one specific thermocouple type (e.g. "K", "J"),
one of them can be configured to work with several different thermocouple
types.
In certain applications thermocouples could be externally connected to the
chip by the user.
This patch introduces a new IIO standard attribute to report the supported
thermocouple type and, where applicable, to allow it to be dynamically set
using sysfs.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch introduces IIO_VAL_CHAR type for standard IIO attributes to
allow for attributes that needs to be represented by character rather
than a number. This is preparatory for introducing a new attribute whose
purpose is to describe thermocouple type, that can be i.e. "J", "K", etc..
The char-type value is stored in the first "value" integer that is passed
to the .[read/write]_raw() callbacks.
Note that in order to make it possible for the IIO core to correctly parse
this type (actually, to avoid integer parsing), it became mandatory for
any driver that wish to use IIO_VAL_CHAR on a writable attribute to
implement .write_raw_get_fmt().
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can perform samples averaging in hardware, but currently the
driver leaves this setting alone (default is no averaging).
This patch binds this HW setting to the "oversampling_ratio" IIO attribute
and allows the user to set the averaging as desired (the HW supports
averaging of 2, 5, 8 or 16 samples; in-between values are rounded up).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor has an embedded notch filter for reducing interferences caused
by the power mains. This filter can be tuned to reject either 50Hz or 60Hz
(and harmonics).
Currently the said setting is left alone (the sensor defaults to 60Hz).
This patch introduces a IIO attribute that allows the user to set the said
filter to the desired frequency.
NOTE: this has been intentionally not tied to any DT property to allow
the configuration of this setting from userspace, e.g. with a GUI or by
reading a configuration file, or maybe reading a GPIO tied to a physical
switch or accessing some device that can autodetect the line frequency.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change uses the ADIS library's state_lock to protect the state of the
`max_speed_hz` change that is done during the set of the sampling
frequency.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's the only operation that does 2 operations (a read & a write), so the
unlocked functions can be used under a single state lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This replaces indio_dev's mlock with the state lock/mutex from the ADIS
library.
The __adis16136_get_freq() function has been prefixed to mark it as
unlocked. The adis16136_{set,get}_filter() functions now hold the state
lock for all the ops that they do.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change removes the use of indio_dev's mlock in favor using the state
lock from the ADIS library.
The set_freq() & get_freq() hooks are unlocked, so they require specific
locking. That is because in some cases the get_freq() hook is used in
combination with adis16400_set_filter().
In cases where only one read/write is done, the functions that hold the
state lock are used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The single conversion function does a series of reads + writes. This change
extends the use of the state_lock for the entire set of operations.
Previously, indio_dev's mlock was used. This change also removes the use of
this lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The initial startup routine is called by some ADIS drivers during probe,
and before registering with IIO. Normally, userspace should not be able to
do any access to the device (as there shouldn't be any available).
This change extends the state lock to the entire initial-startup routine.
Behaviourally nothing should change, but this should make the library
function a bit more robust.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis_enable_irq() does a read & a write. This change keeps a lock for
the duration of both operations vs for each op.
The change is also needed in adis16480, since that has it's own
implementation for adis_enable_irq().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).
The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.
What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
