[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On dcn21 this is programmed for tracebuffer support but isn't being
programmed on dcn20.
DMCUB execution hits an undefined address 65000000 on tracebuffer
access.
[How]
Program CW5.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not having support for autoload isn't an error. If the DMUB firmware
doesn't support it then don't return DMUB_STATUS_INVALID.
[How]
Return DMUB_STATUS_OK when ->is_auto_load_done is NULL.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait for PHY init won't finish if the firmware doesn't support it.
[How]
Only hook this functionality up on DCN21 and move it out of DCN20.
For ASIC without support then this should return OK so we don't hang
while waiting in DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screen seen after display is disabled then re-enabled.
Caused by difference in link settings when
switching between different resolutions.
[How]
In PnP case, or whenever the display is
still enabled but the driver is unloaded,
disable link before re-enabling with new link settings.
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training failed randomly when plugging USB-C display in/out.
[How]
If link training failed, reset PHY in link re-training.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong guards were causing the debug option not to run.
[How]
Changed the guard to the correct one, matching the rq, ttu, dlg regs struct
members that need to be guarded. Also log a message when validation starts.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Dali is currently being misinterpreted as Renoir,
as a result uses wrong clk mgr constructor
[HOW]
Add check to init Dali as Raven2 before it can be misidentified
Clean up & fix Raven2 & Dali ASIC checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some function pointers in the hwss function pointer table are
meant to be hw sequencer entry points to be called from dc.
However some of those function pointers are not meant to
be entry points, but instead used as a code reuse/inheritance
tool called directly by other hwss functions, not by dc.
Therefore, we want a more clear separation of which functions
we determine to be interface functions vs the functions we
use within hwss.
[How]
DC interface functions will be stored in:
struct hw_sequencer_funcs
Functions used within HWSS will be stored in:
struct hwseq_private_funcs
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First, to make code more consistent
Second, to get rid of those scenario where we create a second
local pointer to dc when it's already passed in.
[How]
Rename core_dc to dc
Remove duplicate local pointers to dc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the print out of uvd instance loop in amdgpu_uvd_suspend
v2: drop unnecessary brackets
v3: grab ras_intr state once for multiple times use
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise next err_event_athub error cannot call gpu reset. And following
resume sequence will not be affected by this flag.
v2: create function to clear amdgpu_ras_in_intr for modularity of ras driver
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This athub fatal error can be recovered by baco without system-level reboot,
so add a mode to use baco for the recovery. Not affect the default psp reset
situations for now.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently each XGMI node reset wq does not run in parrallel if bound to same
cpu. Make change to bound the xgmi_reset_work item to different cpus.
XGMI requires all nodes enter into baco within very close proximity before
any node exit baco. So schedule the xgmi_reset_work wq twice for enter/exit
baco respectively.
To use baco for XGMI, PMFW supported for baco on XGMI needs to be involved.
The case that PSP reset and baco reset coexist within an XGMI hive never exist
and is not in the consideration.
v2: define use_baco flag to simplify the code for xgmi baco sequence
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This operation is needed when baco entry/exit for ras recovery
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be cleared during every nbif uncorrectable error cleanup work.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To fix issue that ras controller interrupt cannot be triggered anymore after
one time nbif uncorrectable error. And error count is stored in nbif ras object
for query.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change it to external interface.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: add notification when ras controller interrupt generates
Signed-off-by: Le Ma <Le.Ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The same workaround is used for gfx7.
Both PAL and Mesa use it for gfx8 too, so port this commit to
gfx_v8_0_ring_emit_fence_gfx.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Up to this point, those functions are all the same for all ASICs, so
no need to call them by functions pointers. Removing the function
pointers will greatly increase the code readablity. If there is ever
need for those function pointers, we can add it back then.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SPI limits total CS waves in flight per SE to no more than 32 * num_cu and
we need to stuff 40 waves on a CU to completely clean the SGPR. This is
accomplished in the WR by cleaning the SE in two steps, half of the CU per
step.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When security violation from new vbios happens, data fabric is
risky to stop working. So prevent the direct access to DF
mmFabricConfigAccessControl from the new vbios and onwards.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shift and mask were reversed. Noticed by chance.
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
NV10/14 has released. Its time to get NV10/14 bounding box
directly from code.
[How]
Retrieve NV10/14 bounding box data directly from code.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the exposed function prototype so that the caller does not need
to know the MMHUB number.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop smu_send_smc_msg function from ASIC specify structure.
Reuse smu_send_smc_msg_with_param function for smu_send_smc_msg.
Set paramer to 0 for smu_send_msg function, otherwise it will send
with previous paramer value (Not a certain value).
Materialize msg type for smu send message function definition.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Platform TAs will independently toggle DF Cstate.
for instance, get/set topology from xgmi ta. do error
injection from ras ta. In such case, PMFW needs to be
loaded before TAs so that all the subsequent Cstate
calls recieved by PSP FW can be routed to PMFW.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
issue unload_ta_cmd to tOS to unload asd driver
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
asd shared memory is not needed since drivers doesn't
invoke any further cmd to asd directly after the asd
loading. trust application is the one who needs
to talk to asd after the initialization
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For boards greater than ARCTURUS, and under sriov platform,
swSMU is not supported because smu ip block is commented at
guest driver.
Generally for sriov, initialization of smu is moved to host driver.
Thus, smu sw_init and hw_init will not be executed at guest driver.
Without sw structure being initialized in guest driver, swSMU cannot
declare to be supported.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable v_total is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
