MT2712 SoC can provide the rmii reference clock, and the clock
will output from TXC pin only, which means ref_clk pin of external
PHY should connect to TXC pin in this case.
Add corresponding clock and timing settings.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
improve clause 45 support in phylink
These three patches improve the clause 45 support in phylink, fixing
some corner cases that have been noticed with the addition of SFP+
NBASE-T modules, but are actually a little more wisespread than I
initially realised.
The first issue was spotted with a NBASE-T PHY on a SFP+ module plugged
into a mvneta platform. When these PHYs are not operating in USXGMII
mode, but are in a single-lane Serdes mode, they will switch between
one of several different PHY interface modes.
If we call the MAC validate() function with the current PHY interface
mode, we will restrict the supported and advertising masks to the link
modes that the current PHY interface mode supports. For example, if we
determine that we want to start the PHY with an interface mode of
2500BASE-X, then this setup will restrict the advertisement and
supported masks to 2.5G speed link modes.
What we actually want for these PHYs is to allow them to support any
link modes that the PHY supports _and_ the MAC is also capable of
supporting. Without knowing the details of the PHY interface modes that
may be used, we can do this by using PHY_INTERFACE_MODE_NA to validate
and restrict the link modes to any that the MAC supports.
mvpp2 with the 88X3310 PHY avoids this problem, because the validate()
implementation allows all MAC supported speeds not only for
PHY_INTERFACE_MODE_NA, but also for XAUI and 10GKR modes.
The first patch addresses this; current MAC drivers should continue to
work as-is, but there will be a follow-on patch to fixup at least
mvpp2.
The second issue addresses a very similar problem that occurs when
trying to use ethtool to alter the advertisement mask - we call
the MAC validate() function with the current interface mode, the
current support and requested advertisement masks. This immediately
restricts the advertisement in the same way as the above.
This patch series addresses both issues, although the patches are not
in the above order.
v2: fix patch 3 missing 1G link modes for SGMII and RGMII interface
modes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up the mvpp2 validate implementation to adopt the same behaviour as
mvneta:
- only allow the link modes that the specified PHY interface mode
supports with the exception of 1000base-X and 2500base-X.
- use the basex helper to deal with SFP modules that can be switched
between 1000base-X vs 2500base-X.
This gives consistent behaviour between mvneta and mvpp2.
This commit depends on "net: phylink: extend clause 45 PHY validation
workaround" so is not marked for backporting to stable kernels.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e45d1f5288 ("net: phylink: support Clause 45 PHYs on SFP+
modules") added a workaround to support clause 45 PHYs which
dynamically switch their interface mode on SFP+ modules. This was
implemented by validating the PHYs supported/advertising using
PHY_INTERFACE_MODE_NA, rather than the specific interface mode that
we attached the PHY with.
However, we already have a situation where phylink is used to connect
a Marvell 88X3310 PHY which also behaves in exactly the same way, but
which seemingly doesn't need this. The reason seems to be that the
mvpp2 driver sets a whole bunch of link modes for
PHY_INTERFACE_MODE_10GKR down to 10Mb/s, despite 10GBASE-R not actually
supporting anything but 10Gb/s speeds.
When testing with drivers that (correctly) take the mvneta approach,
where the validate() method only returns what can be supported /
advertised for the specified link mode, we find that Clause 45 PHYs do
not behave as we expect: their advertisement is restricted to what
the current link will support, rather than what the PHY supports
through its dynamic switching.
Extend this workaround to all such cases; if we have a Clause 45 PHY
attaching via any means, except in USXGMII, XAUI and RXAUI which are
all unable to support this dynamic switching or have other solutions
to it, then we need to validate using PHY_INTERFACE_MODE_NA.
This should allow mvpp2 to switch to a more conformant validate()
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing ethtool with the Methode DM7052 module, it was noticed
that attempting to set the advertising mask results in the mask being
truncated to the support offered by the currently chosen PHY interface
mode.
When a PHY dynamically changes the PHY interface mode, limiting the
advertising mask in this way is not correct - if the PHY happened to
negotiate 10GBASE-T, and selected 10GBASE-R as the host interface, we
don't want to restrict the advertisement to just 10GBASE-* modes.
Rework setting the advertisement to take account of this; do not pass
the requested advertisement through phylink_validate(), but rely on
the advertisement restriction (supported mask) set when the PHY was
initially setup.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld says:
====================
WireGuard CI and housekeeping
This is a collection of commits gathered during the last 1.5 weeks since
merging WireGuard. If you'd prefer, I can send tree pull requests
instead, but I figure it might be best for now to just send things as
full patch sets to netdev.
The first part of this adds in the CI test harness that we've been using
for quite some time with success. You can type `make` and get the
selftests running in a fresh VM immediately. This has been an
instrumental tool in developing WireGuard, and I think it'd benefit most
from being in-tree alongside the selftests that are already there. Once
this lands, I plan to get build.wireguard.com building wireguard-
linux.git and net-next.git on every single commit pushed, and do so on a
bunch of different architectures. As this migrates into Linus' tree
eventually and then into net.git, I'll get net.git building there too on
every commit. Future work with this involves generalizing it to include
more networking subsystem tests beyond just WireGuard, but one step at a
time. In the process of porting this to the tree, the builder uncovered
a mistake in the config menu file, which the second commit fixes.
The last three commits are small housekeeping things, fixing spelling
mistakes, replacing call_rcu with kfree_rcu, and removing an unused
include.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove <linux/version.h> from the includes for main.c, which is unused.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[Jason: reworded commit message]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two spelling errors in source code comments.
Signed-off-by: Josh Soref <jsoref@gmail.com>
[Jason: rewrote commit message]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the crypto selection submenu depenencies. Otherwise, we'd
wind up issuing warnings in which certain dependencies we also select
couldn't be satisfied. This condition was triggered by the addition of
the test suite autobuilder in the previous commit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WireGuard has been using this on build.wireguard.com for the last
several years with considerable success. It allows for very quick and
iterative development cycles, and supports several platforms.
To run the test suite on your current platform in QEMU:
$ make -C tools/testing/selftests/wireguard/qemu -j$(nproc)
To run it with KASAN and such turned on:
$ DEBUG_KERNEL=yes make -C tools/testing/selftests/wireguard/qemu -j$(nproc)
To run it emulated for another platform in QEMU:
$ ARCH=arm make -C tools/testing/selftests/wireguard/qemu -j$(nproc)
At the moment, we support aarch64_be, aarch64, arm, armeb, i686, m68k,
mips64, mips64el, mips, mipsel, powerpc64le, powerpc, and x86_64.
The system supports incremental rebuilding, so it should be very fast to
change a single file and then test it out and have immediate feedback.
This requires for the right toolchain and qemu to be installed prior.
I've had success with those from musl.cc.
This is tailored for WireGuard at the moment, though later projects
might generalize it for other network testing.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In caif_xmit, there is a crash if the ptr dev is NULL. However, by
returning the error to the callers, the error can be handled. The
patch fixes this issue.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fore200e_send and fore200e_close, the pointers from the arguments
are dereferenced in the variable declaration block and then checked
for NULL. The patch fixes these issues by avoiding NULL pointer
dereferences.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
Simplify IPv4 route offload API
Motivation
==========
The aim of this patch set is to simplify the IPv4 route offload API by
making the stack a bit smarter about the notifications it is generating.
This allows driver authors to focus on programming the underlying device
instead of having to duplicate the IPv4 route insertion logic in their
driver, which is error-prone.
This is the first patch set out of a series of four. Subsequent patch
sets will simplify the IPv6 API, add offload/trap indication to routes
and add tests for all the code paths (including error paths). Available
here [1].
Details
=======
Today, whenever an IPv4 route is added or deleted a notification is sent
in the FIB notification chain and it is up to offload drivers to decide
if the route should be programmed to the hardware or not. This is not an
easy task as in hardware routes are keyed by {prefix, prefix length,
table id}, whereas the kernel can store multiple such routes that only
differ in metric / TOS / nexthop info.
This series makes sure that only routes that are actually used in the
data path are notified to offload drivers. This greatly simplifies the
work these drivers need to do, as they are now only concerned with
programming the hardware and do not need to replicate the IPv4 route
insertion logic and store multiple identical routes.
The route that is notified is the first FIB alias in the FIB node with
the given {prefix, prefix length, table ID}. In case the route is
deleted and there is another route with the same key, a replace
notification is emitted. Otherwise, a delete notification is emitted.
The above means that in the case of multiple routes with the same key,
but different TOS, only the route with the highest TOS is notified.
While the kernel can route a packet based on its TOS, this is not
supported by any hardware devices I am familiar with. Moreover, this is
not supported by IPv6 nor by BIRD/FRR from what I could see. Offload
drivers should therefore use the presence of a non-zero TOS as an
indication to trap packets matching the route and let the kernel route
them instead. mlxsw has been doing it for the past two years.
Testing
=======
To ensure there is no degradation in route insertion rates, I averaged
the insertion rate of 512k routes (/24 and /32) over 50 runs. Did not
observe any degradation.
Functional tests are available here [1]. They rely on route trap
indication, which is only added in the last patch set.
In addition, I have been running syzkaller for the past week with all
four patch sets and debug options enabled. Did not observe any problems.
Patch set overview
==================
Patches #1-#8 gradually introduce the new FIB notifications
Patch #9 converts mlxsw to use the new notifications
Patch #10 converts the remaining listeners and removes the old
notifications
v2:
* Extend fib_find_alias() with another argument instead of introducing a
new function (David Ahern)
RFC: https://patchwork.ozlabs.org/cover/1170530/
[1] https://github.com/idosch/linux/tree/fib-notifier
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike mlxsw, the other listeners to the FIB notification chain do not
require any special modifications as they never considered multiple
identical routes.
This patch removes the old route notifications and converts all the
listeners to use the new replace / delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new notifications mlxsw does not need to handle identical
routes itself, as this is taken care of by the core IPv4 code.
Instead, mlxsw only needs to take care of inserting and removing routes
from the device.
Convert mlxsw to use the new IPv4 route notifications and simplify the
code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new listener is registered to the FIB notification chain it
receives a dump of all the available routes in the system. Instead, make
sure to only replay the IPv4 routes that are actually used in the data
path and are of any interest to the new listener.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patch, when a route is deleted as part
of table flushing, promote the next route in the list, if exists.
Otherwise, simply emit a delete notification.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a route is deleted we potentially need to promote the next route in
the FIB alias list (e.g., with an higher metric). In case we find such a
route, a replace notification is emitted. Otherwise, a delete
notification for the deleted route.
v2:
* Convert to use fib_find_alias() instead of fib_find_first_alias()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a route is added, it should only be notified in case it is the
first route in the FIB alias list with the given {prefix, prefix length,
table ID}. Otherwise, it is not used in the data path and should not be
considered by switch drivers.
v2:
* Convert to use fib_find_alias() instead of fib_find_first_alias()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing a route, its replacement should only be notified in case
the replaced route is of any interest to listeners. In other words, if
the replaced route is currently used in the data path, which means it is
the first route in the FIB alias list with the given {prefix, prefix
length, table ID}.
v2:
* Convert to use fib_find_alias() instead of fib_find_first_alias()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function with another argument, 'find_first'. When set, the
function returns the first FIB alias with the matching {prefix, prefix
length, table ID}. The TOS and priority parameters are ignored. Current
callers are converted to pass 'false' in order to maintain existing
behavior.
This will be used by subsequent patches in the series.
v2:
* New patch
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a new route is notified in the FIB notification chain before
it is inserted to the FIB alias list.
Subsequent patches will use the placement of the new route in the
ordered FIB alias list in order to determine if the route should be
notified or not.
As a preparatory step, change the order so that the route is first
inserted into the FIB alias list and only then notified.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to simplify the IPv4 route offload API,
which will only use two events - replace and delete.
Introduce a temporary version of these two events in order to make the
conversion easier to review.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: some optimizaions related to work task
This series refactors the work task of the HNS3 ethernet driver.
[patch 1/5] uses delayed workqueue to replace the timer for
hclgevf_service task, make the code simpler.
[patch 2/5] & [patch 3/5] unifies current mailbox, reset and
service work into one.
[patch 4/5] allocates a private work queue with WQ_MEM_RECLAIM
for the HNS3 driver.
[patch 5/5] adds a new flag to indicate whether reset fails,
and prevent scheduling service task to handle periodic task
when this flag has been set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
service_task will be scheduled per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.
This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns3 driver may be used in memory reclaim path when it
is the low level transport of a network file system, so it
needs to guarantee forward progress even under memory pressure.
This patch allocates a private WQ with WQ_MEM_RECLAIM set for
both hclge_main and hclgevf_main modules.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four work (mbx_service_task, service_task,
rst_service_task and keep_alive_task)in the hclgevf module,
mbx_service_task is for handling mailbox issue, service_task is
for periodic management issue and rst_service_task is for reset
related issue, keep_alive_task is used to keepalive between PF
and VF, which can be done in a single work.
This patch removes the mbx_service_task, rst_service_task and
keep_alive_task, and moves the related handling to the
service_task work in order to remove concurrency between the four
work and to improve efficiency.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.
This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.
BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a timer is defined to schedule hclgevf_service per
second. To simplify the code, this patch uses the delayed work
instead of timer to schedule hclgevf_serive.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).
This triggered a warning in the 64 bit optimized ipv6_addr_is_*() functions
because sparse doesn't know that the buffer already points to some data in
the correct bitwise integer format. But these were correct and can
therefore be marked with __force to signalize sparse an intended cast to a
specific bitwise type.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).
This triggered a warning in ipv6_get_dsfield() because sparse doesn't know
that the buffer already points to some data in the correct bitwise integer
format. This was already fixed in ipv6_change_dsfield() by the __force
attribute and can be fixed here the same way.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu says:
====================
dpaa2-ptp: support external trigger event
This patch-set is to add external trigger event support for
dpaa2-ptp driver since MC firmware has supported external
trigger interrupt with a new v2 dprtc_set_irq_mask() API.
And extts_clean_up() function in ptp_qoriq driver needs to be
exported with minor fixes for dpaa2-ptp reusing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export extts_clean_up() function so that dpaa2-ptp
driver is able to reuse it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PTP timer supporting external trigger timestamp FIFO,
there is a valid bit in TMR_STAT register indicating the
timestamp is available. For PTP timer without FIFO, there
is not TMR_STAT register.
This patch is to check the valid bit for the FIFO before
reading timestamp, and to avoid operating TMR_STAT register
for PTP timer without the FIFO.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, if the last frag of paged data in a skb has < PAGE_SIZE
data, we compute the recv_skip_hint as being equal to the size of that
frag and the entire next skb.
Instead, just return the runt frag size as the hint.
recv_skip_hint is used by the application to skip over
bytes that can not be mmaped, so returning a too big
chunk is pessimistic and forces more bytes to be copied.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Save a line of code by making use of ATOMIC_INIT() for lgr_cnt.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
of_phy_attach() hides the return value of phy_attach_direct(), forcing
us to return a "generic" ENODEV error code that is indistinguishable
from the lack-of-phy-property case.
Switch to using of_phy_find_device() to find the PHY device, and then
propagating any phy_attach_direct() error back to the caller.
Link: https://lore.kernel.org/lkml/20191210113829.GT25745@shell.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This adds rx_bpdu, tx_bpdu, rx_tcn, tx_tcn, transition_blk,
transition_fwd xstats counters to the bridge ports copied over via
netlink, providing useful information for STP.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The SO_TXTIME test depends on accurate timers. In some virtualized
environments the test has been reported to be flaky. This is easily
reproduced by disabling kvm acceleration in Qemu.
Allow greater variance in a run and retry to further reduce flakiness.
Observed errors are one of two kinds: either the packet arrives too
early or late at recv(), or it was dropped in the qdisc itself and the
recv() call times out.
In the latter case, the qdisc queues a notification to the error
queue of the send socket. Also explicitly report this cause.
Link: https://lore.kernel.org/netdev/CA+FuTSdYOnJCsGuj43xwV1jxvYsaoa_LzHQF9qMyhrkLrivxKw@mail.gmail.com
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The bond slave actor/partner operating state is exported as
bitfield to userspace, which lacks a way to interpret it, e.g.,
iproute2 only prints the state as a number:
ad_actor_oper_port_state 15
For userspace to interpret the bitfield, the bitfield definitions
should be part of the uapi. The bitfield itself is defined in the
802.3ad standard.
This commit moves the 802.3ad bitfield definitions to uapi.
Related iproute2 patches, soon to be posted upstream, use the new uapi
headers to pretty-print bond slave state, e.g., with ip -d link show
ad_actor_oper_port_state_str <active,short_timeout,aggregating,in_sync>
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This reverts commit 78beef629f ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").
The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.
If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Michael S. Tsirkin says:
====================
netdev: ndo_tx_timeout cleanup
Yet another forward declaration I missed. Hopfully the last one ...
A bunch of drivers want to know which tx queue triggered a timeout,
and virtio wants to do the same.
We actually have the info to hand, let's just pass it on to drivers.
Note: tested with an experimental virtio patch by Julio.
That patch itself isn't ready yet though, so not included.
Other drivers compiled only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameeh Jubran says:
====================
Introduce XDP to ena
This patchset includes 3 patches:
* XDP_DROP implementation
* XDP_TX implementation
* A fix for an issue which might occur due to the XDP_TX patch. I see fit
to place it as a standalone patch for clarity.
Difference from v2:
* Fixed the usage of rx headroom (XDP_PACKET_HEADROOM)
* Aligned the page_offset of the packet when passing it to the stack
* Switched to using xdp_frame in xdp xmit queue
* Dropped the print for unsupported commands
* Cosmetic changes
Difference from RFC v1 (XDP_DROP patch):
* Initialized xdp.rxq pointer
* Updated max_mtu on attachment of xdp and removed the check from
ena_change_mtu()
* Moved the xdp execution from ena_rx_skb() to ena_clean_rx_irq()
* Moved xdp buff (struct xdp_buff) from rx_ring to the local stack
* Started using netlink's extack mechanism to deliver error messages to
the user
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
