Allow to modify ethernet headers while decapsulating mpls over UDP
packets. This is implemented using the same reformat object used for
decapsulation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MPLS over UDP is supported in hardware by using a packet reformat object
with reformat type equal L3_TUNNEL_TO_L2 which both decapsulates the
outer L3, L4 and MPLS headers, and allows for setting the L2 headers of
the resulting decapsulated packet. For the hardware to operate
correctly, the configuration of the firmware must have
FLEX_PARSER_PROFILE_ENABLE = 1.
Example tc rule:
tc filter add dev bareudp0 protocol all prio 1 root flower enc_dst_port \
6635 enc_src_ip 8.8.8.23 action mpls pop protocol ip pipe \
action pedit ex munge eth dst set 00:11:22:33:44:21 pipe action \
mirred egress redirect dev enp59s0f0_0
We use pedit to set the correct destination MAC.
For MPLS over UDP decapsulation to take place, the driver logic requires
the following:
1. flower filter added on bareudp device.
2. action mpls pop
3. zero or more pedit munge actions
4. one redirect action
Current implementation supports only IPv4 and no VLAN.
tc filter show output looks like this:
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
enc_src_ip 8.8.8.24
enc_dst_port 6635
in_hw in_hw_count 1
action order 1: mpls pop protocol ip pipe
index 2 ref 1 bind 1
action order 2: pedit action pipe keys 2
index 1 ref 1 bind 1
key #0 at eth+0: val 00112233 mask 00000000
key #1 at eth+4: val 44210000 mask 0000ffff
action order 3: mirred (Egress Redirect to device enp59s0f0_0) stolen
index 2 ref 1 bind 1
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support matching on MPLS over UDP parameters using misc2 section of
match parameters.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MPLS over UDP is supported by adding a rule on a representor net device
which does tunnel_key set, push mpls and forward to a baredup device. At
the hardware level we use a packet_reformat_context object to do the
encapsulation of the packet.
The resulting packet looks as follows (left side transmitted first):
outer L2 | outer IP | UDP | MPLS | inner L3 and data |
Example usage:
tc filter add dev $rep0 protocol ip prio 1 root flower skip_sw \
action tunnel_key set src_ip 8.8.8.21 dst_ip 8.8.8.24 id 555 \
dst_port 6635 tos 4 ttl 6 csum action mpls push protocol 0x8847 \
label 555 tc 3 action mirred egress redirect dev bareudp0
This is how the filter is shown with tc filter show:
tc filter show dev enp59s0f0_0 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
skip_sw
in_hw in_hw_count 1
action order 1: tunnel_key set
src_ip 8.8.8.21
dst_ip 8.8.8.24
key_id 555
dst_port 6635
csum
tos 0x4
ttl 6 pipe
index 1 ref 1 bind 1
action order 2: mpls push protocol mpls_uc label 555 tc 3 ttl 255 pipe
index 1 ref 1 bind 1
action order 3: mirred (Egress Redirect to device bareudp0) stolen
index 1 ref 1 bind 1
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add netif_is_bareudp() so the device can be identified as a bareudp one.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to improve code maintainability and readability, introduce new
CONFIG_MLX5_CLS_ACT kconfig variable to control compilation of TC hardware
offloads implementation. This allows distinguishing between features that
require TC support (MPLSoUDP, etc.) and features that just rely on
representor functionality (rep_bond for live migration, etc.).
Modify rep_tc.h, rep_neigh.h, en_tc.h and chains.h files to provide stubs
for functions that are called from generic code.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract TC-specific code from
en_main.c to en_tc.c. This allows easily compiling out the code by
only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_main.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract neigh-specific code
from en_rep.c to standalone file. This allows easily compiling out the code
by only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_rep.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As a preparation for introducing new kconfig option that controls
compilation of all TC offloads code in mlx5, extract TC-specific code from
en_rep.c to standalone file. This allows easily compiling out the code by
only including new source in make file when corresponding kconfig is
enabled instead of adding multiple ifdef blocks to en_rep.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use IS_ERR() and PTR_ERR() instead of PTR_ERR_OR_ZERO() to
simplify code, avoid redundant judgements.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Upon adapter hotplug, cxgb4 registers ULD devices for all the ULDs that
are already loaded, ensuring that ULD's can enumerate the hotplugged
adapter without reloading the ULD.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make FLOW_ACTION_HW_STATS_DONT_CARE be all bits, rather than none, so that
drivers and __flow_action_hw_stats_check can use simple bitwise checks.
Pre-fill all actions with DONT_CARE in flow_rule_alloc(), rather than
relying on implicit semantics of zero from kzalloc, so that callers which
don't configure action stats themselves (i.e. netfilter) get the correct
behaviour by default.
Only the kernel's internal API semantics change; the TC uAPI is unaffected.
v4: move DONT_CARE setting to flow_rule_alloc() for robustness and simplicity.
v3: set DONT_CARE in nft and ct offload.
v2: rebased on net-next, removed RFC tags.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko says:
====================
ip6_tunnel: add MPLS support
The support for MPLS-in-IPv4 was added earlier. This patchset adds
support for MPLS-in-IPv6.
Changes in v2:
- Eliminate ifdefs IS_ENABLE(CONFIG_MPLS)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 tunnel devices in AF_MPLS.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is just preparation for MPLS support in ip6_tunnel
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge ip{4,6}ip6_tnl_xmit functions into one universal
ipxip6_tnl_xmit in preparation for adding MPLS support.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski says:
====================
mediatek: add support for MediaTek Ethernet MAC
This series adds support for the STAR Ethernet Controller present on MediaTeK
SoCs from the MT8* family.
First we convert the existing DT bindings for the PERICFG controller to YAML
and add a new compatible string for mt8516 variant of it. Then we add the DT
bindings for the MAC.
Next we do some cleanup of the mediatek ethernet drivers directory.
The largest patch in the series adds the actual new driver.
The rest of the patches add DT fixups for the boards already supported
upstream.
v1 -> v2:
- add a generic helper for retrieving the net_device associated with given
private data
- fix several typos in commit messages
- remove MTK_MAC_VERSION and don't set the driver version
- use NET_IP_ALIGN instead of a magic number (2) but redefine it as it defaults
to 0 on arm64
- don't manually turn the carrier off in mtk_mac_enable()
- process TX cleanup in napi poll callback
- configure pause in the adjust_link callback
- use regmap_read_poll_timeout() instead of handcoding the polling
- use devres_find() to verify that struct net_device is managed by devres in
devm_register_netdev()
- add a patch moving all networking devres helpers into net/devres.c
- tweak the dma barriers: remove where unnecessary and add comments to the
remaining barriers
- don't reset internal counters when enabling the NIC
- set the net_device's mtu size instead of checking the framesize in
ndo_start_xmit() callback
- fix a race condition in waking up the netif queue
- don't emit log messages on OOM errors
- use dma_set_mask_and_coherent()
- use eth_hw_addr_random()
- rework the receive callback so that we reuse the previous skb if unmapping
fails, like we already do if skb allocation fails
- rework hash table operations: add proper timeout handling and clear bits when
appropriate
v2 -> v3:
- drop the patch adding priv_to_netdev() and store the netdev pointer in the
driver private data
- add an additional dma_wmb() after reseting the descriptor in
mtk_mac_ring_pop_tail()
- check the return value of dma_set_mask_and_coherent()
- improve the DT bindings for mtk-eth-mac: make the reg property in the example
use single-cell address and size, extend the description of the PERICFG
phandle and document the mdio sub-node
- add a patch converting the old .txt bindings for PERICFG to yaml
- limit reading the DMA memory by storing the mapped addresses in the driver
private structure
- add a patch documenting the existing networking devres helpers
v3 -> v4:
- drop the devres patches: they will be sent separately
- call netdev_sent_queue() & netdev_completed_queue() where appropriate
- don't redefine NET_IP_ALIGN: define a private constant in the driver
- fix a couple typos
- only disabe/enable the MAC in suspend/resume if netif is running
- drop the count field from the ring structure and instead calculate the number
of used descriptors from the tail and head indicies
- rework the locking used to protect the ring structures from concurrent
access: use cheaper spin_lock_bh() and completely disable the internal
spinlock used by regmap
- rework the interrupt handling to make it more fine-grained: onle re-enable
TX and RX interrupts while they're needed, process the stats updates in a
workqueue, not in napi context
- shrink the code responsible for unmapping and freeing skb memory
- rework the barriers as advised by Arnd
v4 -> v5:
- rename the driver to make it less confusing with the existing mtk_eth_soc
ethernet driver
- unregister the mdiobus at device's detachment
- open-code spin lock calls to avoid calling the _bh variants where unnecessary
- limit read-modify-write operations where possible when accessing descriptor
memory
- use READ_ONCE/WRITE_ONCE when modifying the status and data_ptr descriptor
fields
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add remaining properties to the ethernet node and enable it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the pin control for the Ethernet MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethernet0 alias for ethernet so that u-boot can find this node
and fill in the MAC address.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Ethernet MAC node to mt8516.dtsi. This defines parameters common
to all the boards based on this SoC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PERICFG register range as a syscon. This will
soon be used by the MediaTek Ethernet MAC driver for NIC configuration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the driver for the MediaTek STAR Ethernet MAC currently used
on the MT8* SoC family. For now we only support full-duplex.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Makefile formatting in the kernel tree usually doesn't use tabs,
so remove them before we add a second driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll soon by adding a second MediaTek Ethernet driver so modify the
Kconfig prompt.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds yaml DT bindings for the MediaTek STAR Ethernet MAC present
on the mt8* family of SoCs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PERICFG controller is present on the MT8516 SoC. Add an appropriate
compatible variant.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the DT binding .txt file for MediaTek's peripheral configuration
controller to YAML. There's one special case where the compatible has
three positions. Otherwise, it's a pretty normal syscon.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arthur Kiyanovski says:
====================
ENA features and cosmetic changes
Diff from V1 of this patchset:
Removed error prints patch
This patchset includes:
1. new rx offset feature
2. reduction of the driver load time
3. multiple cosmetic changes to the code
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit reduces the driver load time by using usec resolution
instead of msec when polling for hardware state change.
Also add back-off mechanism to handle cases where minimal sleep
time is not enough.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use BIT macro instead of shift operator for code clarity
2. Replace multiple flag assignments to a single assignment of multiple
flags in ena_com_add_single_rx_desc()
3. Move ENA_HASH_KEY_SIZE from ena_netdev.h to ena_com.h
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add leading and trailing spaces to several comments for better
readability
2. Make tabs and spaces uniform in enum defines in ena_admin_defs.h
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Reorder sanity checks in get_comp_ctxt() to make more sense
2. Reorder variables in ena_com_fill_hash_function() and
ena_calc_io_queue_size() in reverse christmas tree.
3. Move around member initializations.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove unused definition of DRV_MODULE_VERSION
2. Remove {} from single line-of-code ifs
3. Remove unnecessary comments from ena_get/set_coalesce()
4. Remove unnecessary extra spaces and newlines
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Join unnecessarily broken short lines in ena_com.c ena_netdev.c
2. Fix Indentations of broken lines
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix spelling and grammar mistakes in comments in ena_com.h,
ena_com.c and ena_netdev.c
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all types of variables that convey the number and sizeof queues to
be u32, for consistency with the API between the driver and device via
ena_admin_defs.h:ena_admin_get_feat_resp.max_queue_ext fields. Current
code sometimes uses int and there are multiple assignments between these
variables with different types.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ena_update_tx/rx_rings_intr_moderation() to
ena_update_tx/rx_rings_nonadaptive_intr_moderation()
to distinguish between adaptive and non adaptive interrupt moderaion.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize prev_intr_delay_resolution with ena_dev->intr_delay_resolution
unconditionally, since it is initialized with
ENA_DEFAULT_INTR_DELAY_RESOLUTION in ena_probe(). This approach makes much
more sense than handling errors of not initializing it.
Also added unlikely to if condition.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default return value should be -EINVAL since the input
in this case was unexpected.
Also remove the now redundant check in the beginning
of the function.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use u64 instead of unsigned long long for clarity
Signed-off-by: Shai Brandes <shaibran@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ena_com_free_desc to ena_com_free_q_entries to match
the LLQ mode.
In non-LLQ mode, an entry in an IO ring corresponds to a
a descriptor. In LLQ mode an entry may correspond to several
descriptors (per LLQ definition).
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer ENA devices can write data to rx buffers with an offset
from the beginning of the buffer.
This commit adds support for this feature in the driver.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: atlantic: QoS implementation
This patch series adds support for mqprio rate limiters and multi-TC:
* max_rate is supported on both A1 and A2;
* min_rate is supported on A2 only;
This is a joint work of Mark and Dmitry.
To implement this feature, a couple of rearrangements and code
improvements were done, in areas of TC/ring management, allocation
control, etc.
One of the problems we faced is conflicting ptp functionality, which
consumes a whole traffic class due to hardware limitations.
Patches below have a more detailed description on how PTP and multi-TC
co-exist right now.
v2:
* accommodated review comments (-Wmissing-prototypes and
-Wunused-but-set-variable findings);
* added user notification in case of conflicting multi-TC<->PTP
configuration;
* added automatic PTP disabling, if a conflicting configuration is
detected;
* removed module param, which was used for PTP disabling in v1;
v1: https://patchwork.ozlabs.org/cover/1294380/
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an inconsistency between code and spec, which
was found while working on the QoS implementation.
When 8TCs are used, 2 is the maximum supported number of index bits.
In a 4TC mode, we do support 3, but we shouldn't really use the bytes,
which are intended for the 8TC mode.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mqprio min_rate limiters.
A2 HW supports Weighted Strict Priority (WSP) arbitration for Tx Descriptor
Queue scheduling among TCs, which can be used for min_rate shaping.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the order of arguments for TC weight/credit setter
functions.
Having the "value to be set" on the right is slightly more robust in
a sense that it's more natural for the humans, so it's a bit more
error-proof this way.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
